AHSU10 / AMSU10

30,000 LB First Layer Line Pull

DIMENSIONAL INFORMATION
DIMENSIONS SHOWN Mechanical Drive Single Speed Motor
INCHES 23.98
29.25 (mm) -10 SAE ORB
(743) (609) PORT A
(7/8-14 THD)
4.25 12.31 15.98
(108) (312) (405) 4.00
.53
5.50 (101) (13)
(139)
.47
14.00 (12)
(3.55) 3.00 5.30
(76) (135) -10 SAE ORB
PORT B
1.04
17.72 (26)
(7/8-14 THD)
(450) 13.79
(350)
6.30
4.30 2-Speed Motor
(160)
6.00 (109)
(152) 4.19
(106) PORT A

9 in. Drum is also available. 10.75 .71 (18)

1.63 TYP
(273)
12.40
Consult Factory for Specifications. (41) 12V DC
SHIFT
(315) 8.40 SOLENOID
47.50
(213) 1.49 2X -10 ORB PORT
(1206) (38) (7/8 -14 THD)
LEFT HAND ASSEMBLY SHOWN. 5.11
27.85 (130)
(707)
29.09
(739)

• Tested in compliance with SAE Specification J706.

• High-strength aluminum bronze worm gear for long gear life.
• Rugged and compact design.
• Oil-cooled, fully adjustable automatic worm brake.
• Tapered roller bearings provide extra capacity in carrying worm thrust and radial OPTIONAL EXTENSION SHAFT MODELS
loads. SEE LIT2030 FOR SPECIFICATIONS

• Heat treated alloy steel drum shaft for extra load capacity. PACR WINCH DIVISION
P.O. Box 547 Broken Arrow, Oklahoma 74013
• Free spool clutch with negative draft jaws for positive engagement under load. PHONE: (918) 251-8511 FAX: (918) 259-1575
www.paccarwinch.com
COPYRIGHT 2002 PRINTED IN U.S.A. LIT2010 REV1
PACCAR WINCH DIVISION AHSU10 / AMSU10 APRIL 2002
 AHSU10 / AMSU10
PERFORMANCE INFORMATION PERFORMANCE FORMULAS
Single Speed Performance LINE PULL AT LOWER PRESSURE
YOUR SYSTEM PRESSURE LINE PULL LINE PULL
24.0 cu in. (393 cc)
2,800 ∆ psi (193 ∆ bar) @ 35 gpm (132 lpm) MAXIMUM PRESSURE
x FROM CHART = ESTIMATE
(FROM CHART)
WIRE ROPE !
CAUTION

WARNING !
LAYER

LINE PULL LINE SPEED ROPE CAPACITY The products described herein are LINE SPEED AT LOWER FLOW
neither designed nor intended for
use or application to equipment YOUR SYSTEM FLOW LINE SPEED LINE SPEED
(lbs) (kg) (fpm) (mpm) (ft) (m) used in lifting or moving of persons.
MAXIMUM FLOW
x FROM CHART = ESTIMATE
1 30,000 13,635 17 5.2 37 11.3 CAUTION

! WARNING ! (FROM CHART)

2 25,240 11,472 20 6.1 83 25.3
A minimun of 5 wraps of wire rope
3 21,780 9,899 23 7.0 140 42.7 must be left on the drum to prevent
ENGINEERING DATA
the load from being supported by
4 19,160 8,708 27 8.2 200 61.0 the wire rope anchor alone. Since
the wire rope anchor is not
5 17,100 7,772 30 9.2 270 82.4 designed to hold the rated load,
Worm Gear Ratio………… ……...33:1
failure to leave 5 wraps of wire rope
6 15,440 7,017 33 10.1 350 106.8 on the drum could cause the load
Drum Barrel Diameter………………6" (150 mm)
to drop, which could result in
property damage, personal injury or
death.
Oil Capacity………………..4.5 pints
2-Speed Performance Input Shaft Diameter………
….1.25 in. (31.75 mm)
25.8/12.9 cu in. (423/211 cc) Weight - (Winch Only)……
….450 lbs. (204 kg)
2,300 ∆ psi (159 ∆ bar) @ 30 gpm (114 lpm)
Low Speed High Speed MECHANICAL REQUIREMENTS:
Layer

LINE PULL LINE SPEED LINE PULL LINE SPEED Static Input Torque Dynamic Input Torque M ax Input*
(lbs) (kg) (fpm) (mpm) (lbs) (kg) (fpm) (mpm) lb-in N-m lb-in N-m RPM

1 30,000 13,500 12 3.6 13,500 6,100 25 7.5 8,070 912 6,140 694 330
* AT RATED LOAD
2 25,200 11,300 15 4.5 11,400 5,100 30 9.0
3 21,800 9,800 17 5.1 9,800 4,400 34 10.2 NOTES
4 19,200 8,600 20 6.0 8,600 3,900 39 11.7
5 17,100 7,700 22 6.6 7,700 3,500 44 13.2 Specifications are subject to change without notification
6 15,400 6,900 24 7.2 6,900 3,100 49 14.7 and without incurring obligation.

WIRE ROPE CAPACITY Pressure and flow shown are the maximum allowable for
the particular combination of winch, ratio, motor and drum.
ROPE LAYER
Specifications in this publication are theoritical and may
SIZE 1 2 3 4 5 6 7 8
in. ft (m ) ft (m ) ft (m ) ft (m ) ft (m ) ft (m ) ft (m ) ft (m ) vary depending on hydraulic system, environment, etc.
3/4 26 7.9 57 17.4 94 28.7 137 41.8 186 56.7 0.0 0.0 0.0 Line pulls are maximum ratings for the winch only.
5/8 30 9.1 66 20.1 108 32.9 156 47.5 209 63.7 268 81.7 0.0 0.0 Wire rope ratings may be lower than the the winch rating.
9/16 33 10.1 72 21.9 117 35.7 168 51.2 225 68.6 287 87.5 355 108.2 429 130.8 Consult the wire rope manufacturer for ratings.
WIRE ROPE CAPACITY IS 90% OF THEORITICAL.

www.paccarwinch.com AHSU10 / AMSU10