ES8388

Low Power Stereo Audio CODEC

With Headphone Amplifier

GENERAL DESCRIPTION FEATURES

ES8388 is a high performance, low ADC

power and low cost audio CODEC. • 24-bit, 8 kHz to 96 kHz sampling frequency
It consists of 2-ch ADC, 2-ch DAC, • 95 dB dynamic range, 95 dB signal to noise ratio,
microphone amplifier, headphone -85 dB THD+N
amplifier, digital sound effects, and • Stereo or mono microphone interface with
analog mixing and gain functions. microphone amplifier
• Auto level control and noise gate
The device uses advanced multi-bit • 2-to-1 analog input selection
delta-sigma modulation technique • Various analog input mixing and gains
to convert data between digital and DAC
analog. The multi-bit delta-sigma • 24-bit, 8 kHz to 96 kHz sampling frequency
modulators make the device with • 96 dB dynamic range, 96 dB signal to noise ratio,
low sensitivity to clock jitter and low -83 dB THD+N
out of band noise. • 40 mW headphone amplifier, pop noise free
• Headphone capless mode
• Stereo enhancement
• Bass and Treble
• Various analog output mixing and gains
Low Power
• 1.8V to 3.3V operation
• 7 mW playback; 16 mW playback and record
System
• I2C or SPI uC interface
• 256Fs, 384Fs, USB 12 MHz or 24 MHz
• Master or slave serial port
•
2
I S, Left Justified, DSP/PCM Mode

APPLICATIONS ORDERING INFORMATION

• MID ES8388 -40°C ~ +85°C

• MP3, MP4, PMP QFN-28
• Wireless audio
• Digital camera, camcorder
• GPS
• Bluetooth
• Portable audio devices
Revision 11.0 1 January 2023
Latest datasheet: www.everest-semi.com or [email protected]
Everest Semiconductor ES8388

1 BLOCK DIAGRAM ............................................................................................................. 4

2 28-PIN QFN AND PIN DESCRIPTIONS ............................................................................ 5
3 TYPICAL APPLICATION CIRCUIT .................................................................................... 7
4 CLOCK MODES AND SAMPLING FREQUENCIES ......................................................... 7
5 MICRO-CONTROLLER CONFIGURATION INTERFACE ................................................. 9
5.1 SPI ..................................................................................................................................... 9
5.2 2-wire .............................................................................................................................. 10
6 CONFIGURATION REGISTER DEFINITION ................................................................... 11
6.1 Chip Control and Power Management ............................................................................ 13
6.1.1 Register 0 – Chip Control 1, Default 0000 0110 .............................................. 13
6.1.2 Register 1 – Chip Control 2, Default 0101 1100 .............................................. 13
6.1.3 Register 2 – Chip Power Management, Default 1100 0011 ........................... 14
6.1.4 Register 3 – ADC Power Management, Default 1111 1100............................ 14
6.1.5 Register 4 – DAC Power Management, Default 1100 0000 .......................... 15
6.1.6 Register 5 – Chip Low Power 1, Default 0000 0000 ....................................... 15
6.1.7 Register 6 – Chip Low Power 2, Default 0000 0000 ....................................... 15
6.1.8 Register 7 – Analog Voltage Management, Default 0111 1100 ..................... 15
6.1.9 Register 8 – Master Mode Control, Default 1000 0000 .................................. 16
6.2 ADC Control ................................................................................................................... 16
6.2.1 Register 9 – ADC Control 1, Default 0000 0000 .............................................. 16
6.2.2 Register 10 – ADC Control 2, Default 0000 0000............................................ 17
6.2.3 Register 11 – ADC Control 3, Default 0000 0010 ............................................ 17
6.2.4 Register 12 – ADC Control 4, Default 0000 0000............................................ 18
6.2.5 Register 13 – ADC Control 5, Default 0000 0110 ............................................ 18
6.2.6 Register 14 – ADC Control 6, Default 0011 0000 ............................................ 19
6.2.7 Register 15 – ADC Control 7, Default 0010 0000............................................ 19
6.2.8 Register 16 – ADC Control 8, Default 1100 0000 ............................................ 19
6.2.9 Register 17 – ADC Control 9, Default 1100 0000 ............................................ 20
6.2.10 Register 18 – ADC Control 10, Default 0011 1000 .......................................... 20
6.2.11 Register 19 – ADC Control 11, Default 1011 0000 .......................................... 20
6.2.12 Register 20 – ADC Control 12, Default 0011 0010 .......................................... 21
6.2.13 Register 21 – ADC Control 13, Default 0000 0110 .......................................... 22
6.2.14 Register 22 – ADC Control 14, Default 0000 0000 ......................................... 22
6.3 DAC Control ................................................................................................................... 22
6.3.1 Register 23 – DAC Control 1, Default 0000 0000 ........................................... 22
6.3.2 Register 24 – DAC Control 2, Default 0000 0110 ............................................ 23
6.3.3 Register 25 – DAC Control 3, Default 0010 0010 ........................................... 23
6.3.4 Register 26 – DAC Control 4, Default 1100 0000 ............................................ 24
6.3.5 Register 27 – DAC Control 5, Default 1100 0000 ............................................ 24
6.3.6 Register 28 – DAC Control 6, Default 0000 1000 ........................................... 24
6.3.7 Register 29 – DAC Control 7, Default 0000 0000 ........................................... 24
6.3.8 Register 30 – DAC Control 8, Default 0001 1111 ............................................ 25
6.3.9 Register 31 – DAC Control 9, Default 1111 0111 ............................................. 25
Revision 11.0 2 January 2023
Latest datasheet: www.everest-semi.com or [email protected]
Everest Semiconductor ES8388

6.3.10 Register 32 – DAC Control 10, Default 1111 1101 .......................................... 25

6.3.11 Register 33 – DAC Control 11, Default 1111 1111 ........................................... 25
6.3.12 Register 34 – DAC Control 12, Default 0001 1111 .......................................... 25
6.3.13 Register 35 – DAC Control 13, Default 1111 0111 ........................................... 25
6.3.14 Register 36 – DAC Control 14, Default 1111 1101 .......................................... 25
6.3.15 Register 37 – DAC Control 15, Default 1111 1111 ........................................... 26
6.3.16 Register 38 – DAC Control 16, Default 0000 0000 ......................................... 26
6.3.17 Register 39 – DAC Control 17, Default 0011 1000.......................................... 26
6.3.18 Register 40 – DAC Control 18, Default 0010 1000 ......................................... 26
6.3.19 Register 41 – DAC Control 19, Default 0010 1000 ......................................... 26
6.3.20 Register 42 – DAC Control 20, Default 0011 1000.......................................... 27
6.3.21 Register 43 – DAC Control 21, Default 0000 0000 ......................................... 27
6.3.22 Register 44 – DAC Control 22, Default 0000 0000 ......................................... 27
6.3.23 Register 45 – DAC Control 23, Default 0000 0000 ......................................... 27
6.3.24 Register 46 – DAC Control 24, Default 0000 0000 ......................................... 27
6.3.25 Register 47 – DAC Control 25, Default 0000 0000 ......................................... 28
6.3.26 Register 48 – DAC Control 26, Default 0000 0000 ......................................... 28
6.3.27 Register 49 – DAC Control 27, Default 0000 0000 ......................................... 28
6.3.28 Register 50 – DAC Control 28, Default 0000 0000 ......................................... 29
6.3.29 Register 51 – DAC Control 29, Default 1010 1010 ......................................... 29
6.3.30 Register 52 – DAC Control 30, Default 1010 1010 ......................................... 29
7 Digital Audio Interface ...................................................................................................... 29
8 ELECTRICAL CHARACTERISTICS ................................................................................ 30
8.1 Absolute Maximum Ratings ........................................................................................... 30
8.2 Recommended Operating Conditions ............................................................................. 31
8.3 ADC Analog and Filter Characteristics and Specifications ............................................ 31
8.4 DAC Analog and Filter Characteristics and Specifications ............................................ 32
8.5 Power Consumption Characteristics ............................................................................... 32
8.6 Serial Audio Port Switching Specifications .................................................................... 33
8.7 Serial Control Port Switching Specifications .................................................................. 34
9 PACKAGE INFORMATION (UNIT: MM) .......................................................................... 35
10 CORPOARATION INFORMATION .............................................................................. 36
11 IMPORTANT NOTICE AND DISCLAIMER .................................................................. 36

Revision 11.0 3 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
Everest Semiconductor ES8388

1 BLOCK DIAGRAM

DVDD PVDD DGND AVDD AGND HPVDD HPGND ADCVREF VREF VMID

mux
LIN1
LIN2 LIN
mux LIN + mixL
micL DACL
LIN1 mux mixL LOUT1
LIN2 mic amp mixR ROUT1
ADC ALC
micL+micR
LIN1-RIN1 SE DAC DACL
LIN2-RIN2 mixL LOUT2
mux mixR ROUT2
RIN1
RIN2 RIN
mux RIN + mixR
micR DACR
RIN1 mux
RIN2 mic amp
ADC ALC
micL+micR
LIN1-RIN1 SE DAC DACR
LIN2-RIN2

Clock Manager uC Interface Serial Audio Data

MCLK CE CCLK CDATA LRCK ASDOUT DSDIN SCLK

Revision 11.0 4 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
Everest Semiconductor ES8388

2 28-PIN QFN AND PIN DESCRIPTIONS

CDATA
CCLK

RIN1
LIN1

LIN2
NC
CE
28
27
26
25
24
23
22
MCLK 1 21 RIN2
DVDD 2 20 VMID
PVDD 3 19 ADCVREF
DGND 4 18 AGND
SCLK 5 17 AVDD
DSDIN 6 16 HPVDD
LRCK 7 10 15 LOUT2

12
13
14
11
8
9
ASDOUT

HPGND
ROUT1

ROUT2
LOUT1
VREF
NC

Revision 11.0 5 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

ES8388 is pin and size compatible to WM8988.

PIN NAME I/O DESCRIPTION

1 MCLK I Master clock
2 DVDD Supply Digital core supply
3 PVDD Supply Digital IO supply
4 DGND Supply Digital ground (return path for both DVDD and PVDD)
5 SCLK I/O Audio data bit clock
6 DSDIN I DAC audio data
7 LRCK I/O Audio data left and right clock
8 ASDOUT O ADC audio data
9 NC No connect
10 VREF O Decoupling capacitor
11 ROUT1 O Right output 1 (line or headphone)
12 LOUT1 O Left output 1 (line or headphone)
13 HPGND Supply Ground for analog output drivers (LOUT1/2, ROUT1/2)
14 ROUT2 O Right output 2 (line or headphone)
15 LOUT2 O Left output 2 (line or headphone)
16 HPVDD Supply Supply for analog output drivers (LOUT1/2, ROUT1/2)
17 AVDD Supply Analog supply
18 AGND Supply Analog ground
19 ADCVREF O Decoupling capacitor
20 VMID O Decoupling capacitor
21 RIN2 I Right channel input 2
22 LIN2 I Left channel input 2
23 RIN1 I Right channel input 1
24 LIN1 I Left channel input 1
25 NC No connect
26 CE I Control select or device address selection
27 CDATA I/O Control data input or output
28 CCLK I Control clock input

Revision 11.0 6 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
Everest Semiconductor ES8388

3 TYPICAL APPLICATION CIRCUIT

4 CLOCK MODES AND SAMPLING FREQUENCIES

According to the input serial audio data sampling frequency, the device can
work in two speed modes: single speed or double speed. The ranges of the
sampling frequency in these two modes are listed in Table 1. The device can
work either in master clock mode or slave clock mode.

In slave mode, LRCK and SCLK are supplied externally. LRCK and SCLK
must be synchronously derived from the system clock with specific rates. The
device can auto detect MCLK/LRCK ratio according to Table 1. The device
only supports the MCLK/LRCK ratios listed in Table 1. The LRCK/SCLK ratio is
normally 64.

Table 1 Slave Mode Sampling Frequencies and MCLK/LRCK Ratio

Speed Mode Sampling Frequency MCLK/LRCK Ratio
Single Speed 8kHz – 50kHz 256, 384, 512, 768, 1024
Double Speed 50kHz – 100kHz 128, 192, 256, 384, 512

In master mode, LRCK and SCLK are derived internally from MCLK. The
available MCLK/LRCK ratios and SCLK/LRCK ratios are listed in Table 2.

Revision 11.0 7 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
Everest Semiconductor ES8388

Table 2 Master Mode Sampling Frequencies and MCLK/LRCK Ratio

MCLK MCLK ADC Sample Rate ADCFsRatio DAC Sample Rate DACFsRatio SCLK
CLKDIV2=0 CLKDIV2=1 (ALRCK) [4:0] (DLRCK) [4:0] Ratio

Normal Mode
12.288 MHz 24.576MHz 8 kHz (MCLK/1536) 01010 8 kHz (MCLK/1536) 01010 MCLK/6

8 kHz (MCLK/1536) 01010 48 kHz (MCLK/256) 00010 MCLK/4

12 kHz (MCLK/1024) 00111 12 kHz (MCLK/1024) 00111 MCLK/4

16 kHz (MCLK/768) 00110 16 kHz (MCLK/768) 00110 MCLK/6

24 kHz (MCLK/512) 00100 24 kHz (MCLK/512) 00100 MCLK/4

32 kHz (MCLK/384) 00011 32 kHz (MCLK/384) 00011 MCLK/6

48 kHz (MCLK/256) 00010 8 kHz (MCLK/1536) 01010 MCLK/4

48 kHz (MCLK/256) 00010 48 kHz (MCLK/256) 00010 MCLK/4

96 kHz (MCLK/128) 00000 96 kHz (MCLK/128) 00000 MCLK/2

11.2896 MHz 22.5792MHz 8.0182 kHz (MCLK/1408) 01001 8.0182 kHz (MCLK/1408) 01001 MCLK/4

8.0182 kHz (MCLK/1408) 01001 44.1 kHz (MCLK/256) 00010 MCLK/4

11.025 kHz (MCLK/1024) 00111 11.025 kHz (MCLK/1024) 00111 MCLK/4

22.05 kHz (MCLK/512) 00100 22.05 kHz (MCLK/512) 00100 MCLK/4
44.1 kHz (MCLK/256) 00010 8.0182 kHz (MCLK/1408) 01001 MCLK/4
44.1 kHz (MCLK/256) 00010 44.1 kHz (MCLK/256) 00010 MCLK/4

88.2 kHz (MCLK/128) 00000 88.2 kHz (MCLK/128) 00000 MCLK/2

18.432 MHz 36.864MHz 8 kHz (MCLK/2304) 01100 8 kHz (MCLK/2304) 01100 MCLK/6

8 kHz (MCLK/2304) 01100 48 kHz (MCLK/384) 00011 MCLK/6

12 kHz (MCLK/1536) 01010 12 kHz (MCLK/1536) 01010 MCLK/6
16 kHz (MCLK/1152) 01000 16 kHz (MCLK/1152) 01000 MCLK/6

24 kHz (MCLK/768) 00110 24 kHz (MCLK/768) 00110 MCLK/6

32 kHz (MCLK/576) 00101 32 kHz (MCLK/576) 00101 MCLK/6

48 kHz (MCLK/384) 00011 8 kHz (MCLK/2304) 01100 MCLK/6

48 kHz (MCLK/384) 00011 48 kHz (MCLK/384) 00011 MCLK/6

96 kHz (MCLK/192) 00001 96 kHz (MCLK/192) 00001 MCLK/3

16.9344 MHz 33.8688MHz 8.0182 kHz (MCLK/2112) 01011 8.0182 kHz (MCLK/2112) 01011 MCLK/6

8.0182 kHz (MCLK/2112) 01011 44.1 kHz (MCLK/384) 00011 MCLK/6

11.025 kHz (MCLK/1536) 01010 11.025 kHz (MCLK/1536) 01010 MCLK/6

22.05 kHz (MCLK/768) 00110 22.05 kHz (MCLK/768) 00110 MCLK/6
44.1 kHz (MCLK/384) 00011 8.0182 kHz (MCLK/2112) 01011 MCLK/6

44.1 kHz (MCLK/384) 00011 44.1 kHz (MCLK/384) 00011 MCLK/6

88.2 kHz (MCLK/192) 00001 88.2 kHz (MCLK/192) 00001 MCLK/3

USB Mode
12 MHz 24MHz 8 kHz (MCLK/1500) 11011 8 kHz (MCLK/1500) 11011 MCLK

8 kHz (MCLK/1500) 11011 48 kHz (MCLK/250) 10010 MCLK

8.0214 kHz (MCLK/1496) 11010 8.0214 kHz (MCLK/1496) 11010 MCLK

8.0214 kHz (MCLK/1496) 11010 44.118 kHz (MCLK/272) 10011 MCLK

Revision 11.0 8 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
Everest Semiconductor ES8388

11.0259 kHz 11001 11.0259 kHz 11001 MCLK

(MCLK/1088) (MCLK/1088)

12 kHz (MCLK/1000) 11000 12 kHz (MCLK/1000) 11000 MCLK

16 kHz (MCLK/750) 10111 16 kHz (MCLK/750) 10111 MCLK

22.0588 kHz (MCLK/544) 10110 22.0588 kHz (MCLK/544) 10110 MCLK

24 kHz (MCLK/500) 10101 24 kHz (MCLK/500) 10101 MCLK

32 kHz (MCLK/375) 10100* 32 kHz (MCLK/375) 10100* MCLK

44.118 kHz (MCLK/272) 10011 8.0214 kHz (MCLK/1496) 11010 MCLK

44.118 kHz (MCLK/272) 10011 44.118 kHz (MCLK/272) 10011 MCLK

48 kHz (MCLK/250) 10010 8 kHz (MCLK/1500) 11011 MCLK

48 kHz (MCLK/250) 10010 48 kHz (MCLK/250) 10010 MCLK

88.235 kHz (MCLK/136) 10001 88.235 kHz (MCLK/136) 10001 MCLK

96 kHz (MCLK/125) 10000 96 kHz (MCLK/125) 10000 MCLK

5 MICRO-CONTROLLER CONFIGURATION INTERFACE

The device supports standard SPI and 2-wire micro-controller configuration
interface. External micro-controller can completely configure the device
through writing to internal configuration registers. Please see section 8 for the
details of configuration register definition.

The identical device pins are used to configure either SPI or 2-wire interface. In
SPI mode, pin CE, CCLK and CDATA function as SPI_CSn, SPI_CLK and
SPI_DIN. In 2-wire mode, pin CE, CCLK and CDATA function as AD0, SCL and
SDA. To select SPI mode, apply high to low transition signal to CE pin.
Otherwise the device will operate in 2-wire interface mode.

5.1 SPI
ES8388 has a SPI (Serial Peripheral Interface) compliant synchronous serial
slave controller inside the chip. It provides the ability to allow the external
master SPI controller to access the internal registers, and thus control the
operations of chip.

All lines on the SPI bus are unidirectional: The SPI_CLK is generated by the
master controller and is primarily used to synchronize data transfer, the
SPI_DIN line carries data from the master to the slave; SPI_CSn is generated
by the master to select ES8388.

The timing diagram of this interface is given in Figure 1. The high to low
transition at SPI_CSn pin indicates the SPI interface selected. Each write
procedure contains 3 words, i.e. Chip Address plus R/W bit, internal register
address and internal register data. Every word length is fixed at 8 bits. The
input SPI_DIN data are sampled at the rising edge of SPI_CLK clock. The
Revision 11.0 9 January 2023
Latest datasheet: www.everest-semi.com or [email protected]
Everest Semiconductor ES8388

MSB bit in each word is transferred firstly. The transfer rate can be up to 10M
bps.

Chip Address R/ RAM Register Data

SPI_DIN 7 bits - 0010000 Wb 8 bits 8 bits
0 1 5 6 7 8 9 14 15 16 17 22 23
SPI_CLK

SPI_CSn

RAM = Register Address Mapping

Figure 1 SPI Configuration Interface Timing Diagram

5.2 2-wire
The device supports standard 2-wire micro-controller configuration interface.
External micro-controller can completely configure the device through writing
to internal configuration registers.

2-wire interface is a bi-directional serial bus that uses a serial data line (SDA)
and a serial clock line (SCL) for data transfer. The timing diagram for data
transfer of this interface is given in Figure 2a and Figure 2b. Data are
transmitted synchronously to SCL clock on the SDA line on a byte-by-byte
basis. Each bit in a byte is sampled during SCL high with MSB bit being
transmitted firstly. Each transferred byte is followed by an acknowledge bit
from receiver to pull the SDA low. The transfer rate of this interface can be up
to 400 kbps.

A master controller initiates the transmission by sending a “start” signal, which

is defined as a high-to-low transition at SDA while SCL is high. The first byte
transferred is the slave address. It is a seven-bit chip address followed by a
RW bit. The chip address must be 001000x, where x equals AD0. The RW bit
indicates the slave data transfer direction. Once an acknowledge bit is
received, the data transfer starts to proceed on a byte-by-byte basis in the
direction specified by the RW bit. The master can terminate the communication
by generating a “stop” signal, which is defined as a low-to-high transition at
SDA while SCL is high.

In 2-wire interface mode, the registers can be written and read. The formats of
“write” and “read” instructions are shown in Table 1 and Table 2. Please note
that, to read data from a register, you must set R/W bit to 0 to access the
register address and then set R/W to 1 to read data from the register.

Revision 11.0 10 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

Table 3 Write Data to Register in 2-wire Interface Mode

Chip Address R/W Register Address Data to be written
start 001000 AD0 0 ACK RAM ACK DATA ACK Stop

Figure 2a 2-wire Write Timing

Table 4 Read Data from Register in 2-wire Interface Mode

Chip Address R/W Register Address
Start 001000 AD0 0 ACK RAM ACK
Chip Address R/W Data to be read
Start 001000 AD0 1 ACK Data NACK Stop

Figure 2b 2-wire Read Timing

6 CONFIGURATION REGISTER DEFINITION

SPI and 2-wire configuration interface share the same registers because there
is only one interface active at any time. There are total of 53 user
programmable 8-bit registers in this device. These registers control the
operations of ADC and DAC. External master controller can access these
registers by using the slave address specified in RAM (Register Address Map)
register as shown in the Table 5.

Table 5 Bit Content of Register Address Map

B7 B6 B5 B4 B3 B2 B1 B0

Reg. 00 SCPReset LRCM DACMCLK SameFs SeqEn EnRef VMIDSEL

Reg. 01 LPVcmMod LPVrefBuf PdnAna PdnIbiasgen VrefrLo PdnVrefbuf

Revision 11.0 11 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

Reg. 02 adc_DigPDN dac_DigPDN adc_stm_rst dac_stm_rst ADCDLL_PDN DACDLL_PDN adcVref_PDN dacVref_PDN

Reg. 03 PdnAINL PdnAINR PdnADCL PdnADCR PdnMICB PdnADCBiasgen flashLP int1LP

Reg. 04 PdnDACL PdnDACR LOUT1 ROUT1 LOUT2 ROUT2

Reg. 05 LPDACL LPDACR LPLOUT1 LPLOUT2

Reg. 06 LPPGA LPLMIX LPADCvrp LPDACvrp

Reg. 07 VSEL

Reg. 08 MSC MCLKDIV2 BCLK_INV BCLKDIV

Reg. 09 MicAmpL MicAmpR

Reg. 10 LINSEL RINSEL DSSEL DSR

Reg. 11 DS MONOMIX TRI

Reg. 12 DATSEL ADCLRP ADCWL ADCFORMAT

Reg. 13 ADCFsMode ADCFsRatio

Reg. 14 ADC_invL ADC_invR ADC_HPF_L ADC_HPF_R

Reg. 15 ADCRampRate ADCSoftRamp ADCLeR ADCMute

Reg. 16 LADCVOL

Reg. 17 RADCVOL

Reg. 18 ALCSEL MAXGAIN MINGAIN

Reg. 19 ALCLVL ALCHLD

Reg. 20 ALCDCY ALCATK

Reg. 21 ALCMODE ALCZC TIME_OUT WIN_SIZE

Reg. 22 NGTH NGG NGAT

Reg. 23 DACLRSWAP DACLRP DACWL DACFORMAT

Reg. 24 DACFsMode DACFsRatio

Reg. 25 DACRampRate DACSoftRamp DACLeR DACMute

Reg. 26 DACVolumeL (LDACVOL)

Reg. 27 DACVolumeR (RDACVOL)

Reg. 28 DeemphasisMode DAC_invL DAC_invR ClickFree

Reg. 29 ZeroL ZeroR Mono SE Vpp_scale

Reg. 30 Shelving_a[29:24]

Reg. 31 Shelving_a[23:16]

Reg. 32 Shelving_a[15:8]

Reg. 33 Shelving_a[7:0]

Reg. 34 Shelving_b[29:24]

Reg. 35 Shelving_b[23:16]

Reg. 36 Shelving_b[15:8]

Reg. 37 Shelving_b[7:0]

Reg. 38 LMIXSEL RMIXSEL

Reg. 39 LD2LO LI2LO LI2LOVOL

Reg. 40

Reg. 41

Reg. 42 RD2RO RI2RO RI2ROVOL

Revision 11.0 12 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

Reg. 43 slrck Lrck_sel offset_dis, mclk_dis Adc_dll_pwd Dac_dll_pwd

Reg. 44 offset

Reg. 45 VROI

Reg. 46 LOUT1VOL

Reg. 47 ROUT1VOL

Reg. 48 LOUT2VOL

Reg. 49 ROUT2VOL

Reg. 50

Reg. 51 hpLout1_ref1 hpLout1_ref2

Reg. 52 spkLout2_ref1 spkLout2_ref2 mixer_ref1 mixer_ref2 MREF1 MREF2

6.1 Chip Control and Power Management

6.1.1 Register 0 – Chip Control 1, Default 0000 0110

Bit Name Bit Description
SCPReset 7 0 – normal (default)
1 – reset control port register to default
LRCM 6 0 – ALRCK disabled when both ADC disabled; DLRCK disabled when both DAC disabled (default)
1 – ALRCK and DLRCK disabled when all ADC and DAC disabled
DACMCLK 5 0 – when SameFs=1, ADCMCLK is the chip master clock source (default)
1 – when SameFs=1, DACMCLK is the chip master clock source
SameFs 4 0 – ADC Fs differs from DAC Fs (default)
1 – ADC Fs is the same as DAC Fs
SeqEn 3 0 – internal power up/down sequence disable (default)
1 – internal power up/down sequence enable
EnRef 2 0 – disable reference
1 – enable reference (default)
VMIDSEL 1:0 00 – Vmid disabled
01 – 50 kΩ divider enabled
10 – 500 kΩ divider enabled (default)
11 – 5 kΩ divider enabled

6.1.2 Register 1 – Chip Control 2, Default 0101 1100

Bit Name Bit Description
LPVcmMod 5 0 – normal (default)
1 – low power
LPVrefBuf 4 0 – normal
1 – low power (default)
PdnAna 3 0 – normal
1 – entire analog power down (default)
PdnIbiasgen 2 0 – normal

Revision 11.0 13 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

1 – ibiasgen power down (default)

VrefLo 1 0 – normal (default)
1 – low power
PdnVrefbuf 0 0 – normal (default)
1 – power down

6.1.3 Register 2 – Chip Power Management, Default 1100 0011

Bit Name Bit Description
adc_DigPDN 7 0 – normal
1 – resets ADC DEM, filter and serial data port (default)
dac_DigPDN 6 0 – normal
1 – resets DAC DSM, DEM, filter and serial data port (default)
adc_stm_rst 5 0 – normal (default)
1 – reset ADC state machine to power down state
dac_stm_rst 4 0 – normal (default)
1 – reset DAC state machine to power down state
ADCDLL_PDN 3 0 – normal (default)
1 – ADC_DLL power down, stop ADC clock
DACDLL_PDN 2 0 – normal (default)
1 – DAC DLL power down, stop DAC clock
adcVref_PDN 1 0 – ADC analog reference power up
1 – ADC analog reference power down (default)
dacVref_PDN 0 0 – DAC analog reference power up
1 – DAC analog reference power down (default)

6.1.4 Register 3 – ADC Power Management, Default 1111 1100

Bit Name Bit Description
PdnAINL 7 0 – normal
1 – left analog input power down (default)
PdnAINR 6 0 – normal
1 – right analog input power down (default)
PdnADCL 5 0 – left ADC power up
1 – left ADC power down (default)
PdnADCR 4 0 – right ADC power up
1 – right ADC power down (default)
PdnMICB 3 0 – microphone bias power on
1 – microphone bias power down (high impedance output, default)
PdnADCBiasgen 2 0 – normal
1 – power down (default)
flashLP 1 0 – normal (default)
1 – flash ADC low power
int1LP 0 0 – normal (default)
1 – int1 low power
Revision 11.0 14 January 2023
Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

6.1.5 Register 4 – DAC Power Management, Default 1100 0000

Bit Name Bit Description
PdnDACL 7 0 – left DAC power up
1 – left DAC power down (default)
PdnDACR 6 0 – right DAC power up
1 – right DAC power down (default)
LOUT1 5 0 – LOUT1 disabled (default)
1 – LOUT1 enabled
ROUT1 4 0 – ROUT1 disabled (default)
1 – ROUT1 enabled
LOUT2 3 0 – LOUT2 disabled (default)
1 – LOUT2 enabled
ROUT2 2 0 – ROUT2 disabled (default)
1 – ROUT2 enabled

6.1.6 Register 5 – Chip Low Power 1, Default 0000 0000

Bit Name Bit Description
LPDACL 7 0 – normal (default)
1 – low power
LPDACR 6 0 – normal (default)
1 – low power
LPLOUT1 5 0 – normal (default)
1 – low power
LPLOUT2 3 0 – normal (default)
1 – low power

6.1.7 Register 6 – Chip Low Power 2, Default 0000 0000

Bit Name Bit Description
LPPGA 7 0 – normal (default)
1 – low power
LPLMIX 6 0 – normal (default)
1 – low power
LPADCvrp 1 0 – normal (default)
1 – low power
LPDACvrp 0 0 – normal (default)
1 – low power

6.1.8 Register 7 – Analog Voltage Management, Default 0111 1100

Bit Name Bit Description
VSEL 6:0 1111100 – normal (default)

Revision 11.0 15 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

6.1.9 Register 8 – Master Mode Control, Default 1000 0000

Bit Name Bit Description
MSC 7 0 – slave serial port mode
1 – master serial port mode (default)
MCLKDIV2 6 0 – MCLK not divide (default)
1 – MCLK divide by 2
BCLK_INV 5 0 – normal (default)
1 – BCLK inverted
BCLKDIV 4:0 00000 – master mode BCLK generated automatically based on the clock table (default)
00001 – MCLK/1
00010 – MCLK/2
00011 – MCLK/3
00100 – MCLK/4
00101 – MCLK/6
00110 – MCLK/8
00111 – MCLK/9
01000 – MCLK/11
01001 – MCLK/12
01010 – MCLK/16
01011 – MCLK/18
01100 – MCLK/22
01101 – MCLK/24
01110 – MCLK/33
01111 – MCLK/36
10000 – MCLK/44
10001 – MCLK/48
10010 – MCLK/66
10011 – MCLK/72
10100 – MCLK/5
10101 – MCLK/10
10110 – MCLK/15
10111 – MCLK/17
11000 – MCLK/20
11001 – MCLK/25
11010 – MCLK/30
11011 – MCLK/32
11100 – MCLK/34
Others – MCLK/4

6.2 ADC Control

6.2.1 Register 9 – ADC Control 1, Default 0000 0000

Bit Name Bit Description

Revision 11.0 16 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

MicAmpL 7:4 Left channel PGA gain

0000 – 0 dB (default)
0001 – +3 dB
0010 – +6 dB
0011 – +9 dB
0100 – +12 dB
0101 – +15 dB
0110 – +18 dB
0111 – +21 dB
1000 – +24 dB
MicAmpR 3:0 Right channel PGA gain
0000 – 0dB (default)
0001 – +3 dB
0010 – +6 dB
0011 – +9 dB
0100 – +12 dB
0101 – +15 dB
0110 – +18 dB
0111 – +21 dB
1000 – +24 dB

6.2.2 Register 10 – ADC Control 2, Default 0000 0000

Bit Name Bit Description
LINSEL 7:6 Left channel input select
00 – LINPUT1 (default)
01 – LINPUT2
10 – reserved
11 – L-R differential (either LINPUT1-RINPUT1 or LINPUT2-RINPUT2, selected by DS)
RINSEL 5:4 Right channel input select
00 – RINPUT1 (default)
01 – RINPUT2
10 – reserved
11 – L-R differential (either LINPUT1-RINPUT1 or LINPUT2-RINPUT2, selected by DS)
DSSEL 3 0 – use one DS Reg11[7] (default)
1 – DSL=Reg11[7], DSR=Reg10[2]
DSR 2 Differential input select
0 – LINPUT1-RINPUT1 (default)
1 – LINPUT2-RINPUT2

6.2.3 Register 11 – ADC Control 3, Default 0000 0010

Bit Name Bit Description
DS 7 Differential input select
0 – LINPUT1-RINPUT1 (default)

Revision 11.0 17 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

1 – LINPUT2-RINPUT2
MONOMIX 4:3 00 – stereo (default)
01 – analog mono mix to left ADC
10 – analog mono mix to right ADC
11 – reserved
TRI 2 0 – ASDOUT is ADC normal output (default)
1 – ASDOUT tri-stated, ALRCK, DLRCK and SCLK are inputs

6.2.4 Register 12 – ADC Control 4, Default 0000 0000

Bit Name Bit Description
DATSEL 7:6 00 – left data = left ADC, right data = right ADC
01 – left data = left ADC, right data = left ADC
10 – left data = right ADC, right data = right ADC
11 – left data = right ADC, right data = left ADC
ADCLRP 5 I2S, left justified or right justified mode:
0 – left and right normal polarity
1 – left and right inverted polarity
DSP/PCM mode:
0 – MSB is available on 2nd BCLK rising edge after ALRCK rising edge
1 – MSB is available on 1st BCLK rising edge after ALRCK rising edge
ADCWL 4:2 000 – 24-bit serial audio data word length
001 – 20-bit serial audio data word length
010 – 18-bit serial audio data word length
011 – 16-bit serial audio data word length
100 – 32-bit serial audio data word length
ADCFORMAT 1:0 00 – I2S serial audio data format
01 – left justify serial audio data format
10 – right justify serial audio data format
11 – DSP/PCM mode serial audio data format

6.2.5 Register 13 – ADC Control 5, Default 0000 0110

Bit Name Bit Description
ADCFsMode 5 0 – single speed mode (default)
1 – double speed mode
ADCFsRatio 4:0 Master mode ADC MCLK to sampling frequency ratio

Revision 11.0 18 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

00000 – 128 10000 – 125

00001 – 192 10001 – 136
00010 – 256 10010 – 250
00011 – 384 10011 – 272
00100 – 512 10100 – 375
00101 – 576 10101 – 500
00110 – 768 (default) 10110 – 544
00111 – 1024 10111 – 750
01000 – 1152 11000 – 1000
01001 – 1408 11001 – 1088
01010 – 1536 11010 – 1496
01011 – 2112 11011 – 1500
01100 – 2304
Other – reserved

6.2.6 Register 14 – ADC Control 6, Default 0011 0000

Bit Name Bit Description
ADC_invL 7 0 – normal (default)
1 – left channel polarity inverted
ADC_invR 6 0 – normal (default)
1 – right channel polarity inverted
ADC_HPF_L 5 0 – disable ADC left channel high pass filter
1 – enable ADC left channel high pass filter (default)
ADC_HPF_R 4 0 – disable ADC right channel high pass filter
1 – enable ADC right channel high pass filter (default)

6.2.7 Register 15 – ADC Control 7, Default 0010 0000

Bit Name Bit Description
ADCRampRate 7:6 00 – 0.5 dB per 4 LRCK digital volume control ramp rate (default)
01 – 0.5 dB per 8 LRCK digital volume control ramp rate
10 – 0.5 dB per 16 LRCK digital volume control ramp rate
11 – 0.5 dB per 32 LRCK digital volume control ramp rate
ADCSoftRamp 5 0 – disabled digital volume control soft ramp
1 – enabled digital volume control soft ramp (default)
ADCLeR 3 0 – normal (default)
1 – both channel gain control is set by ADC left gain control register
ADCMute 2 0 – normal (default)
1 – mute ADC digital output

6.2.8 Register 16 – ADC Control 8, Default 1100 0000

Bit Name Bit Description
LADCVOL 7:0 Digital volume control attenuates the signal in 0.5 dB incremental from 0 to –96 dB.
00000000 – 0 dB
Revision 11.0 19 January 2023
Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

00000001 – -0.5 dB
00000010 – -1 dB
…
11000000 – -96 dB (default)

6.2.9 Register 17 – ADC Control 9, Default 1100 0000

Bit Name Bit Description
RADCVOL 7:0 Digital volume control attenuates the signal in 0.5 dB incremental from 0 to –96 dB.
00000000 – 0 dB
00000001 – -0.5 dB
00000010 – -1 dB
…
11000000 – -96 dB (default)

6.2.10 Register 18 – ADC Control 10, Default 0011 1000

Bit Name Bit Description
ALCSEL 7:6 00 – ALC off
01 – ALC right channel only
10 – ALC left channel only
11 – ALC stereo
MAXGAIN 5:3 Set maximum gain of PGA
000 – -6.5 dB
001 – -0.5 dB
010 – 5.5 dB
011 – 11.5 dB
100 – 17.5 dB
101 – 23.5 dB
110 – 29.5 dB
111 – 35.5 dB
MINGAIN 2:0 Set minimum gain of PGA
000 – -12 dB
001 – -6 dB
010 – 0 dB
011 – +6 dB
100 – +12 dB
101 – +18 dB
110 – +24 dB
111 – +30 dB

6.2.11 Register 19 – ADC Control 11, Default 1011 0000

Bit Name Bit Description
ALCLVL 7:4 ALC target
0000 – -16.5 dB

Revision 11.0 20 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

0001 – -15 dB
0010 – -13.5 dB
……
0111 – -6 dB
1000 – -4.5 dB
1001 – -3 dB
1010-1111 – -1.5 dB
ALCHLD 3:0 ALC hold time before gain is increased
0000 – 0ms
0001 – 2.67ms
0010 – 5.33ms
…… (time doubles with every step)
1001 – 0.68s
1010 or higher – 1.36s

6.2.12 Register 20 – ADC Control 12, Default 0011 0010

Bit Name Bit Description
ALCDCY 7:4 ALC decay (gain ramp up) time, ALC mode/limiter mode:
0000 – 410 us/90.8 us
0001 – 820 us/182us
0010 – 1.64 ms/363us
…… (time doubles with every step)
1001 – 210 ms/46.5 ms
1010 or higher – 420 ms/93 ms
ALCATK 3:0 ALC attack (gain ramp down) time, ALC mode/limiter mode:
0000 – 104 us/22.7 us
0001 – 208 us/45.4 us
0010 – 416 us/90.8 us
…… (time doubles with very step)
1001 – 53.2 ms/11.6 ms
1010 or higher – 106 ms/23.2 ms

Revision 11.0 21 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

6.2.13 Register 21 – ADC Control 13, Default 0000 0110

Bit Name Bit Description
ALCMODE 7 Determines the ALC mode of operation:
0 – ALC mode (Normal Operation)
1 – Limiter mode.
ALCZC 6 ALC uses zero cross detection circuit.
0 – disable (recommended)
1 – enable
TIME_OUT 5 Zero Cross time out
0 – disable (default)
1 – enable
WIN_SIZE 4:0 Windows size for peak detector，set the window size to N*16 samples
00110 – 96 samples (default)
00111 – 102 samples
…..
11111 – 496 samples

6.2.14 Register 22 – ADC Control 14, Default 0000 0000

Bit Name Bit Description
NGTH 7:3 Noise gate threshold
00000 – -76.5 dBFS
00001 – -75 dBFS
……
11110 – -31.5 dBFS
11111 – -30 dBFS
NGG 2:1 Noise gate type
x0 – PGA gain held constant
01 – mute ADC output
11 – reserved
NGAT 0 Noise gate function enable
0 – disable
1 – enable

6.3 DAC Control

6.3.1 Register 23 – DAC Control 1, Default 0000 0000

Bit Name Bit Description
DACLRSWAP 7 0 – normal
1 – left and right channel data swap
DACLRP 6 I2S, left justified or right justified mode:
0 – left and right normal polarity
1 – left and right inverted polarity
Revision 11.0 22 January 2023
Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

DSP/PCM mode:
0 – MSB is available on 2nd BCLK rising edge after ALRCK rising edge
1 – MSB is available on 1st BCLK rising edge after ALRCK rising edgeLRCK Polarity
DACWL 5:3 000 – 24-bit serial audio data word length
001 – 20-bit serial audio data word length
010 – 18-bit serial audio data word length
011 – 16-bit serial audio data word length
100 – 32-bit serial audio data word length
DACFORMAT 2:1 00 – I2S serial audio data format
01 – left justify serial audio data format
10 – right justify serial audio data format
11 – DSP/PCM mode serial audio data format

6.3.2 Register 24 – DAC Control 2, Default 0000 0110

Bit Name Bit Description
DACFsMode 5 0 – single speed mode (default)
1 – double speed mode
DACFsRatio 4:0 Master mode DAC MCLK to sampling frequency ratio
00000 — 128; 10000 — 125;
00001 — 192; 10001 — 136;
00010 — 256; 10010 — 250;
00011 — 384; 10011 — 272;
00100 — 512; 10100 — 375;
00101 — 576; 10101 — 500;
00110 — 768; (default) 10110 — 544;
00111 — 1024; 10111 — 750;
01000 — 1152; 11000 — 1000;
01001 — 1408; 11001 — 1088;
01010 — 1536; 11010 — 1496;
01011 — 2112; 11011 — 1500;
01100 — 2304;
Other — Reserved.

6.3.3 Register 25 – DAC Control 3, Default 0010 0010

Bit Name Bit Description
DACRampRate 7:6 00 – 0.5 dB per 4 LRCK digital volume control ramp rate (default)
01 – 0.5 dB per 32 LRCK digital volume control ramp rate
10 – 0.5 dB per 64 LRCK digital volume control ramp rate
11 – 0.5 dB per 128 LRCK digital volume control ramp rate
DACSoftRamp 5 0 – disabled digital volume control soft ramp
1 – enabled digital volume control soft ramp (default)
DACLeR 3 0 – normal (default)
1 – both channel gain control is set by DAC left gain control register
Revision 11.0 23 January 2023
Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

DACMute 2 0 – normal (default)

1 – mute analog outputs for both channels

6.3.4 Register 26 – DAC Control 4, Default 1100 0000

Bit Name Bit Description
LDACVOL 7:0 Digital volume control attenuates the signal in 0.5 dB incremental from 0 to –96 dB.
00000000 – 0 dB
00000001 – -0.5 dB
00000010 – -1 dB
…
11000000 – -96 dB (default)

6.3.5 Register 27 – DAC Control 5, Default 1100 0000

Bit Name Bit Description
RDACVOL 7:0 Digital volume control attenuates the signal in 0.5 dB incremental from 0 to –96 dB.
00000000 – 0 dB
00000001 – -0.5 dB
00000010 – -1 dB
…
11000000 – -96 dB (default)

6.3.6 Register 28 – DAC Control 6, Default 0000 1000

Bit Name Bit Description
DeemphasisMode 7:6 00 – de-emphasis frequency disabled (default)
(DEEMP) 01 – 32 KHz de-emphasis frequency in single speed mode
10 – 44.1 KHz de-emphasis frequency in single speed mode
11 – 48 KHz de-emphasis frequency in single speed mode
DAC_invL 5 0 – normal DAC left channel analog output no phase inversion (default)
1 – normal DAC left channel analog output 180 degree phase inversion
DAC_invR 4 0 – normal DAC right channel analog output no phase inversion (default)
1 – normal DAC right analog output 180 degree phase inversion
ClickFree 3 0 – disable digital click free power up and down
1 – enable digital click free power up and down (default)

6.3.7 Register 29 – DAC Control 7, Default 0000 0000

Bit Name Bit Description
ZeroL 7 0 – normal (default)
1 – set Left Channel DAC output all zero
ZeroR 6 0 – normal (default)
1 – set Right Channel DAC output all zero
Mono 5 0 – stereo (default)
1– mono (L+R)/2 into DACL and DACR
SE 4:2 SE strength
Revision 11.0 24 January 2023
Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

000 – 0 (default)
……
111 – 7
Vpp_scale 1:0 00 – Vpp set at 3.5V (0.7 modulation index) (default)
01 – Vpp set at 4.0V
10 – Vpp set at 3.0V
11 – Vpp set at 2.5V

6.3.8 Register 30 – DAC Control 8, Default 0001 1111

Bit Name Bit Description
Shelving_a[29:24] 5:0 30-bit a coefficient for shelving filter
Default value is {5'h0f, 5'h1f, 5'h0f, 5'h1f, 5'h0f, 5'h1f}

6.3.9 Register 31 – DAC Control 9, Default 1111 0111

Bit Name Bit Description
Shelving_a[23:16] 7:0 30-bit a coefficient for shelving filter
Default value is {5'h0f, 5'h1f, 5'h0f, 5'h1f, 5'h0f, 5'h1f}

6.3.10 Register 32 – DAC Control 10, Default 1111 1101

Bit Name Bit Description
Shelving_a[15:8] 7:0 30-bit a coefficient for shelving filter
Default value is {5'h0f, 5'h1f, 5'h0f, 5'h1f, 5'h0f, 5'h1f}

6.3.11 Register 33 – DAC Control 11, Default 1111 1111

Bit Name Bit Description
Shelving_a[7:0] 7:0 30-bit a coefficient for shelving filter
Default value is {5'h0f, 5'h1f, 5'h0f, 5'h1f, 5'h0f, 5'h1f}

6.3.12 Register 34 – DAC Control 12, Default 0001 1111

Bit Name Bit Description
Shelving_b[29:24] 5:0 30-bit a coefficient for shelving filter
Default value is {5'h0f, 5'h1f, 5'h0f, 5'h1f, 5'h0f, 5'h1f}

6.3.13 Register 35 – DAC Control 13, Default 1111 0111

Bit Name Bit Description
Shelving_b[23:16] 7:0 30-bit a coefficient for shelving filter
Default value is {5'h0f, 5'h1f, 5'h0f, 5'h1f, 5'h0f, 5'h1f}

6.3.14 Register 36 – DAC Control 14, Default 1111 1101

Bit Name Bit Description
Shelving_b[15:8] 7:0 30-bit a coefficient for shelving filter
Default value is {5'h0f, 5'h1f, 5'h0f, 5'h1f, 5'h0f, 5'h1f}

Revision 11.0 25 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

6.3.15 Register 37 – DAC Control 15, Default 1111 1111

Bit Name Bit Description
Shelving_b[7:0] 7:0 30-bit a coefficient for shelving filter
Default value is {5'h0f, 5'h1f, 5'h0f, 5'h1f, 5'h0f, 5'h1f}

6.3.16 Register 38 – DAC Control 16, Default 0000 0000

Bit Name Bit Description
LMIXSEL 5:3 Left input select for output mix
000 – LIN1 (default)
001 – LIN2
010 – reserved
011 – left ADC P input (after mic amplifier)
100 – left ADC N input (after mic amplifier)
RMIXSEL 2:0 Right input select for output mix
000 – RIN1 (default)
001 – RIN2
010 – reserved
011 – right ADC P input (after mic amplifier)
100 – right ADC N input (after mic amplifier)

6.3.17 Register 39 – DAC Control 17, Default 0011 1000

Bit Name Bit Description
LD2LO 7 0 – left DAC to left mixer disable (default)
1 – left DAC to left mixer enable
LI2LO 6 0 – LIN signal to left mixer disable (default)
1 – LIN signal to left mixer enable
LI2LOVOL 5:3 LIN signal to left mixer gain
000 – 6 dB
001 – 3 dB
010 – 0 dB
011 – -3 dB
100 – -6 dB
101 – -9 dB
110 – -12 dB
111 – -15 dB (default)

6.3.18 Register 40 – DAC Control 18, Default 0010 1000

Bit Name Bit Description

6.3.19 Register 41 – DAC Control 19, Default 0010 1000

Bit Name Bit Description

Revision 11.0 26 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

6.3.20 Register 42 – DAC Control 20, Default 0011 1000

Bit Name Bit Description
RD2RO 7 0 – right DAC to right mixer disable (default)
1 – right DAC to right mixer enable
RI2RO 6 0 – RIN signal to right mixer disable (default)
1 – RIN signal to right mixer enable
RI2ROVOL 5:3 RIN signal to right mixer gain
000 – 6 dB
001 – 3 dB
010 – 0 dB
011 – -3 dB
100 – -6 dB
101 – -9 dB
110 – -12 dB
111 – -15 dB (default)

6.3.21 Register 43 – DAC Control 21, Default 0000 0000

Bit Name Bit Description
slrck 7 0 – DACLRC and ADCLRC separate (default)
1 – DACLRC and ADCLRC same
lrck_sel 6 Master mode, if slrck = 1 then
0 – use DAC LRCK (default)
1 – use ADC LRCK
offset_dis 5 0 – disable offset (default)
1 – enable offset
mclk_dis 4 0 – normal (default)
1 – disable MCLK input from PAD
adc_dll_pwd 3 0 – normal (default)
1 – ADC DLL power down
dac_dll_pwd 2 0 – normal (default)
1 – DAC DLL power down

6.3.22 Register 44 – DAC Control 22, Default 0000 0000

Bit Name Bit Description
offset 7:0 DC offset

6.3.23 Register 45 – DAC Control 23, Default 0000 0000

Bit Name Bit Description
VROI 4 0 – 1.5k VREF to analog output resistance (default)
1 – 40k VREF to analog output resistance

6.3.24 Register 46 – DAC Control 24, Default 0000 0000

Bit Name Bit Description
Revision 11.0 27 January 2023
Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

LOUT1VOL 5:0 LOUT1 volume

000000 – -45dB (default)
000001 – -43.5dB
000010 – -42dB
…
011110 – 0dB
011111 – 1.5dB
…
100001 – 4.5dB

6.3.25 Register 47 – DAC Control 25, Default 0000 0000

Bit Name Bit Description
ROUT1VOL 5:0 ROUT1 volume
000000 – -45dB (default)
000001 – -43.5dB
000010 – -42dB
…
011110 – 0dB
011111 – 1.5dB
…
100001 – 4.5dB

6.3.26 Register 48 – DAC Control 26, Default 0000 0000

Bit Name Bit Description
LOUT2VOL 5:0 LOUT2 volume
000000 – -45dB (default)
000001 – -43.5dB
000010 – -42dB
…
011110 – 0dB
011111 – 1.5dB
…
100001 – 4.5dB

6.3.27 Register 49 – DAC Control 27, Default 0000 0000

Bit Name Bit Description
ROUT2VOL 5:0 ROUT2 volume
000000 – -45dB (default)
000001 – -43.5dB
000010 – -42dB
…
011110 – 0dB
011111 – 1.5dB

Revision 11.0 28 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
 Everest Semiconductor ES8388

…
100001 – 4.5dB

6.3.28 Register 50 – DAC Control 28, Default 0000 0000

Bit Name Bit Description

6.3.29 Register 51 – DAC Control 29, Default 1010 1010

Bit Name Bit Description
hpLout1_ref1 7 Reserved
hpLout1_ref2 6 Reserved

6.3.30 Register 52 – DAC Control 30, Default 1010 1010

Bit Name Bit Description
spkLout2_ref1 7 Reserved
spkLout2_ref2 6 Reserved
mixer_ref1 3 Reserved
mixer_ref2 2 Reserved
MREF1 1 Reserved
MREF2 0 Reserved

7 Digital Audio Interface

The device provides four formats of serial audio data interface to the input of
the DAC or output from the ADC through LRCK, SCLK and SDIN/SDOUT pins.
The four formats are I2S, left justified, right justified and DSP/PCM mode. DAC
input DSDIN is sampled by ES8388 on the rising edge of DSCLK. ADC data is
out on ASDOUT and changes on the falling edge of ASCLK. The relationship
of SDATA (SDIN/SDOUT), SCLK and LRCK with the three formats is shown
through Figure 3 to Figure 7.

1 SCLK 1 SCLK
SDATA 1 2 3 n-2 n-1 n 1 2 3 n-2 n-1 n
MSB LSB MSB LSB

SCLK

LEFT CHANNEL
LRCK RIGHT CHANNEL

Figure 3 I2S Serial Audio Data Format Up To 24-bit

SDATA 1 2 3 n-2 n-1 n 1 2 3 n-2 n-1 n

MSB LSB MSB LSB

SCLK

LRCK LEFT CHANNEL RIGHT CHANNEL

Revision 11.0 29 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
Everest Semiconductor ES8388

Figure 4 Left Justified Serial Audio Data Format Up To 24-bit

SDATA 1 2 3 n-2 n-1 n 1 2 3 n-2 n-1 n

MSB LSB MSB LSB

SCLK

LRCK LEFT CHANNEL RIGHT CHANNEL

Figure 5 Right Justified Serial Audio Data Format Up To 24-bit

Figure 6 DSP/PCM Mode A

Figure 7 DSP/PCM Mode B

8 ELECTRICAL CHARACTERISTICS

8.1 Absolute Maximum Ratings

Continuous operation at or beyond these conditions may permanently damage
the device.
PARAMETER MIN MAX
Analog Supply Voltage Level -0.3V +3.6V
Digital Supply Voltage Level -0.3V +3.6V

Revision 11.0 30 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
Everest Semiconductor ES8388

Analog Input Voltage range AGND-0.3V AVDD+0.3V

Digital Input Voltage range DGND-0.3V PVDD+0.3V
Operating Temperature Range -40°C +85°C
Storage Temperature -65°C +150°C

8.2 Recommended Operating Conditions

PARAMETER MIN TYP MAX UNIT
Analog Supply Voltage Level 1.7 1.8/3.3 3.6 V
Digital Supply Voltage Level 1.5 1.8/3.3 3.6 V
Note 1: When LRCK is 8 kHz, 1.8V (±10%) DVDD is recommended. When LRCK is 8 kHz and
3.3V (±10%) DVDD is used, then MCLK/LRCK ratio must be 256, and set reg0x35=0xA0,
reg0x37=0x10 and reg0x39=0x10

8.3 ADC Analog and Filter Characteristics and Specifications

Test conditions are as the following unless otherwise specify:
AVDD=+3.3V, DVDD=+1.8V, AGND=0V, DGND=0V, Ambient
temperature=+25°C, Fs=48 KHz, 96 KHz or 192 KHz, MCLK/LRCK=256.
PARAMETER MIN TYP MAX UNIT
ADC Performance
Dynamic Range (Note 2) 85 95 98 dB
THD+N -88 -85 -75 dB
Channel Separation (1KHz) 80 85 90 dB
Signal to Noise ratio (Note 2) 85 95 98 dB
Interchannel Gain Mismatch 0.1 dB
Gain Error ±5 %
Filter Frequency Response – Single Speed
Passband 0 0.4535 Fs
Stopband 0.5465 Fs
Passband Ripple ±0.05 dB
Stopband Attenuation 50 dB
Filter Frequency Response – Double Speed
Passband 0 0.2268 Fs
Stopband 0.4535 Fs
Passband Ripple ±0.005 dB
Stopband Attenuation 50 dB
Analog Input
Full Scale Input Level AVDD/3.3 Vrms
Input Impedance 20 KΩ
Note 2: The value is measured used A-weighted filter.

Revision 11.0 31 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
Everest Semiconductor ES8388

8.4 DAC Analog and Filter Characteristics and Specifications

Test conditions are as the following unless otherwise specify:
AVDD=+3.3V, DVDD=+1.8V, AGND=0V, DGND=0V, Ambient
temperature=+25°C, Fs=48 KHz, 96 KHz or 192 KHz, MCLK/LRCK=256.
PARAMETER MIN TYP MAX UNIT
DAC Performance
Dynamic Range (Note 3) 83 96 98 dB
THD+N -85 -83 -75 dB
Channel Separation (1KHz) 80 85 90 dB
Signal to Noise ratio (Note 2) 83 96 98 dB
Interchannel Gain Mismatch 0.05 dB
Filter Frequency Response – Single Speed
Passband 0 0.4535 Fs
Stopband 0.5465 Fs
Passband Ripple ±0.05 dB
Stopband Attenuation 40 dB
Filter Frequency Response – Double Speed
Passband 0 0.2268 Fs
Stopband 0.4535 Fs
Passband Ripple ±0.005 dB
Stopband Attenuation 40 dB
De-emphasis Error at 1 KHz (Single Speed Mode Only)
Fs = 32KHz 0.002 dB
Fs = 44.1KHz 0.013
Fs = 48KHz 0.0009
Analog Output
Full Scale Output Level AVDD/3.3 Vrms
Note 3: The value is measured used A-weighted filter.

8.5 Power Consumption Characteristics

PARAMETER MIN TYP MAX UNIT
Normal Operation Mode
DVDD=1.8V, PVDD=1.8V, AVDD=1.8V: mW
Play back 7
Play back and record 16
DVDD=3.3V, PVDD=3.3V, AVDD=3.3V:
Play back 31
Play back and record 59
Power Down Mode
DVDD=1.8V, PVDD=1.8V, AVDD=1.8V 0.3 mW
DVDD=3.3V, PVDD=3.3V, AVDD=3.3V 1.9

Revision 11.0 32 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
Everest Semiconductor ES8388

8.6 Serial Audio Port Switching Specifications

PARAMETER Symbol MIN MAX UNIT
MCLK frequency 51.2 MHz
MCLK duty cycle 40 60 %
LRCK frequency 200 KHz
LRCK duty cycle 40 60 %
SCLK frequency 26 MHz
SCLK pulse width low TSCLKL 15 ns
SCLK Pulse width high TSCLKH 15 ns
SCLK falling to LRCK edge TSLR –10 10 ns
SCLK falling to SDOUT valid TSDO 0 ns
SDIN valid to SCLK rising setup time TSDIS 10 ns
SCLK rising to SDIN hold time TSDIH 10 ns

Figure 8 Serial Audio Port Timing

Revision 11.0 33 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
Everest Semiconductor ES8388

8.7 Serial Control Port Switching Specifications

PARAMETER Symbol MIN MAX UNIT
SPI Mode
SPI_CLK clock frequency 10 MHz
SPI_CLK edge to SPI_CSn falling TSPICS 5 ns
SPI_CSn High Time Between transmissions TSPISH 500 ns
SPI_CSn falling to SPI_CLK edge TSPISC 10 ns
SPI_CLK low time TSPICL 45 ns
SPI_CLK high time TSPICH 45 ns
SPI_DIN to SPI_CLK rising setup time TSPIDS 10 ns
SPI_CLK rising to DATA hold time TSPIDH 15 ns
2-wire Mode
SCL Clock Frequency FSCL 400 KHz
Bus Free Time Between Transmissions TTWID 1.3 us
Start Condition Hold Time TTWSTH 0.6 us
Clock Low time TTWCL 1.3 us
Clock High Time TTWCH 0.4 us
Setup Time for Repeated Start Condition TTWSTS 0.6 us
SDA Hold Time from SCL Falling TTWDH 900 ns
SDA Setup time to SCL Rising TTWDS 100 ns
Rise Time of SCL TTWR 300 ns
Fall Time SCL TTWF 300 ns

TSPIDS TSPIDH

SPI_DIN

TSPICL
SPI_CLK TSPICH

SPI_CSn
TSPISH
TSPICS TSPISC

Figure 9 Serial Control Port SPI Timing

SDA

TTWSTS TTWSTH TTWDH TTWDS TTWID

TTWCL

SCL
TTWCH
S P S
TTWF TTWR

Revision 11.0 Figure 10 Serial Control

34 Port 2-wire Timing January 2023
Latest datasheet: www.everest-semi.com or [email protected]
Everest Semiconductor ES8388

9 PACKAGE INFORMATION (UNIT: MM)

Revision 11.0 35 January 2023

Latest datasheet: www.everest-semi.com or [email protected]
Everest Semiconductor ES8388

10 CORPOARATION INFORMATION
Everest Semiconductor Co., Ltd.
苏州工业园区机场路 328 号，国际科技园区科技广场 6A，邮编 215028
Email: [email protected]

11 IMPORTANT NOTICE AND DISCLAIMER

Everest Semiconductor publishes reliable technical information about its

products. Information contained herein is subject to change without notice. It
may be used by a party at their own discretion and risk. Everest
Semiconductor disclaims responsibility for any claims, damages, costs, losses,
and liabilities arising out of your use of the information. This publication is not
to be taken as a license to operate under any existing patents and intellectual
properties.

Revision 11.0 36 January 2023

Latest datasheet: www.everest-semi.com or [email protected]