SPEC SHEET
FLS-240 pocket pal
VISUAL FAULT LOCATOR (VFL)
The FLS-240 is the easiest way to identify fibers from
end to end and locate polished connector endfaces.
CW and
pulse button
GP-1008 adapter (2.5 mm to 1.25 mm)
KEY FEATURES
Bright red laser at 635 nm
Pulsed and CW operation
50 hours of operation (typical)
Standard AAA alkaline batteries
Rugged and weatherproof
2.5 mm universal connector
FLS-240 pocket pal
The FLS-240 is the easiest way to identify fibers from end to end and locate polished connector endfaces. Its red laser shines
through most yellow-jacketed fibers to help you pinpoint breaks, bends, faulty connectors, splices and other causes of signal loss.
It has a reach of up to 5 km *. The convenient FLS-240 locates faults visually by creating a bright red glow at the exact location of
the fault on singlemode or multimode fibers.
Due to its small size, lightweight and simple but proven design, the FLS-240 can accompany you anywhere. In your pocket or belt
pouch, carry your FLS-240 to the most demanding environments. To ensure ruggedness, it features rubber seals, a fully enclosed
laser head and a long-lasting On/Off switch. It has been tested to provide reliable operation under intensive use and harsh conditions.
* Typical length of continuous fiber at which end-to-end identification is possible. VFL depends on ambient light conditions at test site.
SPECIFICATIONS a GENERAL SPECIFICATIONS
Operation (Hz) 2 to 4 Power supply 2 AAA alkaline batteries
Wavelength (nm) 630 to 645 Laser class 2M
Battery life d (h) CW 35
Emitter type Laser
Pulsed 50
Power output b (typical) (mW) 0.8 Length 17.5 cm (6 7/8 in)
Distance range c (typical) (km) 5 Maximum diameter 2.5 cm (1 in)
Operation mode Pulsed and CW Weight Without batteries 80 g (4.8 oz)
With batteries 120 g (6.3 oz)
Temperature Operating —10 °C to 50 °C (14 °F to 122 °F)
SIX WAYS TO USE A VFL Storage —30 °C to 60 °C (—22 °F to 140 °F)
STANDARD ACCESSORIES
User guide, two AAA alkaline batteries, belt clip and certificate
of compliance
Detects breaks in Highlights sharp bends Optimizes mechanical/
OTDR dead zone. where losses occur. fusion splices.
LASER SAFETY
IEC 60825-1:2007 21 CFR 1040.10
VISIBLE LASER RADIATION DO NOT Complies with 21 CFR 1040.10
STARE INTO THE BEAM OR VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS except for deviations pursuant to
Detects defective
Ensures end-to-end CLASS 2M LASER PRODUCT
λ:635 ± 10 nm Ppk <1 mW
Laser Notice No.50 dated 2007.
fiber identification in
connectors.
multifiber cables.
a. Specifications are valid at 23 °C ± 1 °C.
b. Only valid with 50/125 µm fiber.
c. Depends on fiber attenuation.
d. Typical battery life using AAA alkaline batteries. Battery life may fluctuate significantly, depending on specific unit’s laser current.
ORDERING INFORMATION
FLS-241-UNIV
Universal 2.5 mm ferrule (CW and pulse)
EXFO headquarters T +1 418 683-0211 Toll-free +1 800 663-3936 (USA and Canada)
EXFO serves over 2000 customers in more than 100 countries. To find your local office contact details, please go to www.EXFO.com/contact.
For the most recent patent marking information, please visit www.EXFO.com/patent. EXFO is certified ISO 9001 and attests to the quality of these products. EXFO has made every effort to ensure that
the information contained in this specification sheet is accurate. However, we accept no responsibility for any errors or omissions, and we reserve the right to modify design, characteristics and products
at any time without obligation. Units of measurement in this document conform to SI standards and practices. In addition, all of EXFO’s manufactured products are compliant with the European Union’s
WEEE directive. For more information, please visit www.EXFO.com/recycle. Contact EXFO for prices and availability or to obtain the phone number of your local EXFO distributor.
For the most recent version of this spec sheet, please go to www.EXFO.com/specs.
In case of discrepancy, the web version takes precedence over any printed literature.
FLS240.6EN © 2021 EXFO Inc. All rights reserved. Printed in Canada 21/06
