CERTC REE-RTE-02

COMPLETE ENGINEERING REVIEW AND TRAINING CENTER

Rm 501, G .K. Ch ua Bld g., M. J. Cue nc o Ave. Ce bu Cit y
C o n ta c t N o. 0 91 7 -3 0 2- 8 82 4

REGISTERED ELECTRCAL ENGINEERS LICENSURE EXAMINATION

PROFESSIONALSUBJECTS www.certcreviewhub.com

MULTIPLE CHOICE 11. A length of a copper telephone line has a

resistance of 24 ohms at 20 degrees C. What
1. If the certain conductor has an area of is the resistance on a hot summer day when
336,400 cmils, what is the radius of this its temperature raised to 36 degrees C?
conductor in cm? A. 26.5 ohms C. 25.5 ohms✓
A. 0.663 C. 0.737✓ B. 24.5 ohms D. 27.5 ohms
B. 0.810 D. 0.921
12. A certain copper wire has a resistance of 25
2. A 110 V dc motor draws current of 30 A and is ohms at 10°C . Take the temperature
located 500 ft from the power source. What is
coefficient at 10°C to be 0.00409 deg/C. What
the supply voltage if the diameter of the
must be the maximum operating temperature of
copper wire is 0.25 inch? Resistivity is 10.4
the wire if its resistance is to increase by
ohm-cmil per ft.
at most 20%?
A. 119 V C. 121 V
A. 58.89✓ C. 59.24
B. 117 V D. 115 V✓
B. 60.13 D. 59.25
3. A series loop contains the following circuit
13. The power factor of a load on a 120 volt,
elements in order: a 8-volt source, a 2 kΩ
60Hz source is raised from 0.7070 to 0.866
resistor, a 3 kΩ resistor, a 16-V source and
lagging by connecting a 53 micro-farad
a 7 kΩ resistor. What is the power absorbed
capacitor across the load. What is the tue
by the 3 kΩ resistor/
power of the load in watts?
A. 12 mW✓ C. 0.12 W A. 286 C. 862
B. 1.2 mW D. 1.2 W
B. 682✓ D. 268
4. Three resistors 3, 4, and z ohms respectively
14. Find the force in a conductor of length 50 cm
are connected in parallel across a constant
moving perpendicular at a velocity 590 m/s to
current source of 10 A. Find the value of z
a region of flux density 1 tesla.
if this resistor draws 3 A current.
A. 15 Volts C. 150 Volts
A. 6 ohms C. 4 ohms✓
B. 30 Volts D. 300 Volts✓
B. 2 ohms D. 8 ohms
15. A 120 cm long conductor i carrying a current
5. The voltage applied across the resistor was
of 1.2 A and is situated at right angles to
reduced by 50%. The power consumed by
field of flux density of 0.65T. Calculate the
resistor will reduced by
force on the conductor.
A. 75✓ C. 25 A. 3.264 N C. 1.348 N
B. 50 D. 100
B. 0.936 N✓ D. 1.587 N
6. A 6 V car draws a current of 6.5 A. What
16. Calculate the force in pounds upo each side
resistance in ohms must be connected in
of a coil of 50 turns carrying a current of
series with it to operate it in car with a 12
20 A if the axial length of the coil is 12
V battery?
inch and the flux density is 25,000 lines per
A. 0.947 C. 0.923✓ square inch. There are 4.448 x 105 dynes in a
B. 0.969 D. 0.981 pound. The conductors are at right angles to
7. Three resistors R1 = 9 kΩ, R2 = 9 kΩ, R3 = 9 the flux.
kΩ are connected in parallel across a 12-V A. 29.4 C. 27.9
power supply whose internal resistance is 1 B. 25.3 D. 26.6✓
kΩ. How much current is drawn from the
17. A 10 ohms resistor is connected in parallel
source?
to the impedance of Z = 3+j4. What is the
A. 6 mA C. 2.4 mA
power factor?
B. 3 mA✓ D. 1.2 mA A. 0.6 C. 0.609
8. A 20-ohm resistor is connected in parallel
B. 0.8 D. 0.809✓
with a variable resistor R. The parallel
combination is then connected in series with 18. A coil inductance 10.5 H is connected to a
a 4-ohm resistor and connected across a 240 V source voltage of V = (3t+25.4)1/2. What is
source. Determine the minimum value of R if the current in the inductor after 5.25 sec?
the power of R is equal to the power taken by A. 5.5 A C. 2.88 A✓
the 4-ohm resistor. B. 6.15 A D. 3.22 A
A. 7.95 ohms C. 7.64 ohms✓ 19. A 120 volts dc motor draws 200 ampere is
B. 8.40 ohms D. 6.87 ohms located 1000 ft from the supply line. The
diameter of wire is 0.45 inch, the specific
9. Two batteries are connected in parallel to
resistance is 10.4 ohm cmil per foot. What is
feed a 12-ohm load. Battery A has open
the supply voltage?
circuit emf of 6.3 V and internal resistance
A. 136 C. 129
of 1.5 ohms. Battery B has an open circuit
emf of 6 V and an internal resistance of 2.1 B. 134 D. 140✓
ohms. What is the load current? 20. What is the complex expression for a given
A. 0.48 A✓ C. 0.44 A alternating current, i = 250 sin (wt + 25
B. 0.52 A D. 0.56 A degrees)?
A. 227 + j106 C. 227 – j106
10. The resistance of the length of copper wire
B. 160 – j 75 D. 160 + j75✓
is 2.6 ohms at 20°C . The temperature
21. What is the complex expression for a given
coefficient of resistance at 20°C for copper alternating current i = 250 sin (wt – 25
is 0.0393. what is its resistance at 75°C ? degrees)?
A. 3.670 ohms C. 11.38 ohms A. 227 + j106 C. 160 + j75
B. 3.162 ohms✓ D. 4.378 ohms B. 227 - j106 D. 160 – j75✓

PAGE 1
 CERTC REE-RTE-02
COMPLETE ENGINEERING REVIEW AND TRAINING CENTER
Rm 501, G .K. Ch ua Bld g., M. J. Cue nc o Ave. Ce bu Cit y
C o n ta c t N o. 0 91 7 -3 0 2- 8 82 4

REGISTERED ELECTRCAL ENGINEERS LICENSURE EXAMINATION

PROFESSIONALSUBJECTS www.certcreviewhub.com

22. Find the value of impedance which requires - the line is 2400 V, 60 Hz. What is the
1540 VAR at 230 V rms and 10 A rms. capacitance per phase?
A. 17.40 – j15 ohms A. 21 mF C. 205 mF
B. 17.09 – j 15.39 ohms✓ B. 21 µF D. 205 µF✓
C. 16.82 – j15.69 ohms
D. 17.62 – j14.78 ohms 33. A balanced delta connected load of 4 – j3
ohms per phase is fed by a 380 V, three-phase
23. For a series RLC circuit with elements R = 50 system. Find the reactive power.
Ω, L = 8 mH and C = 2.22 µF. What is the A. 52 kVARS✓ C. 69 kVARS
equivalent impedance of the circuit if its B. 29 kVARS D. 87 kVARS
frequency is 792 Hz?
A. 50 – j50 ohms✓ C. 50 + j50 ohms 34. The phase current in a wye-connected
B. 50 + j130 ohms D. 50 – j130 ohms unbalanced load are la = 44 – j33, lb = -32 –
j24, and lc = -40 + j25 A. What is the
24. Find the current that will flow in series positive sequence current for phase A?
circuit containing a 50 kohm resistor, a 470 A. -28 – j21 A C. 28 – j31 A
picoF capacitor, a 150-mH inductor, and a B. 40.8 + j8.9 A D. 40.8 – j8.9 A✓
0.001 microfarad capacitor if the exciting
voltage is 65 V at 25 kHz. 35. A 240 V (line to neutral) three-phase source
A. 6.32 + j8.46 mA C. 8.46 + j6.22 mA is connected to three 10 ohm resistance loads
B. 6.22 – j8.46 mA D. 8.46 – j6.22 mA✓ with both source and load in the Y-
configuration. Determine the current in each
25. Two impedances, Z1 = 0.8 + j5.6 and Z2 = 8 – phase
j16 and a single-phase motor are connected in A. 22 A C. 24 A✓
parallel across 200 Vrms, 60 Hz supply. The B. 20 A D. 28 A
motor draws 5kVA at 80% power factor lagging.
Find the complex power of impedance Z2? 36. A balanced three phase wye connected source
A. -1 – j2 kVA C. 2 + j1 kVA has using positive hase sequence, Van = 220 V
B. 1 – j2 kVA✓ D. -2 – j1 kVA rms with 30 degrees angle. Determine Vbc.
A. 190.5 + j330 V C. -190.5 – j330 V
26. What are the two elements in a series circuit B. 190.5 – j330 V✓ D. –j381 V
connection having a current and voltage of i
= 13.42 sin (500t – 53.4 degrees) A and n =150 37. In a balanced three-phase system, the wye-
sin (500t + 10 degrees) V? connected impedances connected are 10 ohms
A. R = 8.8 ohms and L = 35 mH with 30 degrees angle. If Vbc is equal to 416
B. R = 6.3 ohms and L = 25 mH V with 240 degrees angle, determine icn.
C. R = 7.5 ohms and L = 30 mH Assume the phase sequence is abc.
D. R = 5.0 ohms and L = 20 mH✓ A. 12 + j20.8 A✓ C. 12 – j20.8 A
B. 20.8 – j12 A D. 20.8 + j12 A
27. The impedance Z3 in series to the two
impedances Z1= 10 + j10 ohms and Z2 = 20 – 38. Given the following phase currents, la = 3.5
j30 ohms that are connected in parallel. What + j 3.5, lb = 0 – j3 and lc = -2.6 + j1.6.
is the value of the impedance Z3 in ohms that Determine the negative sequence current for
will produce resonant circuit? phase A.
A. –j13.1 C. j13.1 A. 0.33 + j0.678✓ C. 0.424 + j0.571
B. j 5.4 D. –j5.4✓ B. -0.333 – j0.678 D.-0.333 + j0.678

28. A 100 picofarad capacitor is connected in 39. What is the maximum flux in a transformer
series with a coil having inductance of 100 µ with 200 turns at the primary when supplied
H and a resistance of 100 ohm. At what by 60 hertz, 240 volts source?
frequency will this network have unity pf. A. 4.5mWb✓ C. 4.13mWb
A. 1.4 MHz C. 1.2 MHz B. 4.04mWb D. 4.32mWb
B. 1.8 MHz D. 1.6 MHz✓ 40. Given the following sets of symmetrical
29. A 125-F capacitor that has an initial voltage components currents, determine the phase B
of 25-V is charge with a current that varies current.
with time according to the equation i = t (t2 Current Magnitude Angle, degrees
+ 6.83)1/2. Find the voltage across the lao 1.0
capacitor at 1 s. 75
A. 26 V C. 20 V la1 1.0
15
B. 25 V✓ D. 20.0 V
la2 1.0
30. Find the current through a 0.1 microfarad -45
capacitor at t = 0, if the voltage across it A. 0.259 + j0.966✓ C. 1.932 + j0.518
is -2 e-10^7t V. B. 0.516 + j1.931 D. 1.414 + j1.414
A. 200 mA C. 20 A 41. A transformer having a 360 turn primary
B. 20 mA D. 2 A✓ winding takes 150 W in power and 1.4 A in
31. In a three phase balanced delta connected current at an input voltage of 230 volts.
load with one line open, line A has 20 A. Determine the no-load power factor.
Assume line A is the reference and the line c A. 0.606 C. 0.466✓
is open. What should be the negative sequence B. 0.866 D. 0.528
of line a?
A. 0 C. 10-j5.77 A 42. Find the work in kWhr to lift 1 ton at a
height of 55 ft for 10 sec. The motor gear
B. 30+j17.32 A D. 10+j5.77 A✓
efficiency is 50%.
32. A balanced three-phase wye-connected load of A. 0.091✓ C. 0.91
150 kW takes a leading current of 100 A, when B. 91 D. 910

PAGE 2
 CERTC REE-RTE-02
COMPLETE ENGINEERING REVIEW AND TRAINING CENTER
Rm 501, G .K. Ch ua Bld g., M. J. Cue nc o Ave. Ce bu Cit y
C o n ta c t N o. 0 91 7 -3 0 2- 8 82 4

REGISTERED ELECTRCAL ENGINEERS LICENSURE EXAMINATION

PROFESSIONALSUBJECTS www.certcreviewhub.com

43. A transformer when it is operated as a 51. A three-phase transposed distribution line is

conventional two winding transformer is rated designed with equilateral spacing of 12 ft.
10 MVA, 12/1.2 kV, 60 Hz. Under these It is decided to build the line with
conditions, its series resistance and horizontal spacing D31 = 2D12 = 2D23. What
reactance are given as 2% and 7% pu should be the spacing between adjacent
respectively. this transformer is to be used conductors in order to obtain the same
as 13.2/12 kV step-down autotransformer in a inductance as the original design?
power distribution system. What is the A. 9.5246 ft✓ C. 9.5066 ft
transformer’s series impedance in pu in the B. 9.6437 ft D. 9.6198 ft
autotransformer connection?
A. 0.0017 + j0.0058 C. 0.0020 + j0.0070 52. A 69-kV three phase transposed line is
B. 0.0022 + j0.0078 D. 0.0018 + j0.0064✓ composed of one ACSR 336,400 cmil, 36/7
Linnet conductor per phase with a horizontal
44. A transformer is rated 500 kVA, 4800/480 V, configuration of D12 = 5 ft, D23 = 5 ft and D13
60 Hz when operated as a conventional two = 10 ft. The conductors have a diameter of
winding transformer. This transformer is to 0.721 inch, resistance of 0.306 ohm per mile
be used as a 5.28/4.8 kV step down and gmr of 0.0244 ft. What is the reactance
autotransformer in power distribution system. for 12 miles line.
In the autotransformer connection, what is A. 6 ohms C. 4 ohms
the transformer’s rating when used in this B. 2 ohms D. 8 ohms✓
manner?
A. 5 MVA C. 5.5 MVA✓ 53. A single circuit transposed overhead
B. 6 MVA D. 6.5 MVA transmission line is composed of tow-
45. The open circuit and short circuit tests were conductors per phase. The diameter of each
performed on the primary side of the 25 kVA, conductor is 5 cm. The distance between the
7620/240, 60 hz transformer and the following center of the bundle is 5 m. What is the
data were obtained, open circuit test; Eoc = inductance per km per phase of the line.
7620 V, Ioc = 0.30 A and Poc = 500 W. Short A. 0.4412 mH C. 0.9325 mH
circuit test Esc = 450 V, Isc = 3.5 A and Psc B. 0.9163 mH D. 0.8825 mH✓
= 220 W. Determine the shunt and series 54. A three-phase circuit, 60 Hz, 230 kV
impedances refer to the primary of the transposed transmission line is composed of
transformer. two 1272 MCM, 54/19 conductors per phase with
A. 116 + j26 kohm and 17.97 + j130 ohm✓ horizontal configuration. The bundle spacing
B. 124 + j14 kohm and 21.85 + j134 ohm is 50 cm while phase spacing between the
C. 112 + j22 kohm and 15.95 + j128 ohm centers of the bundle is 10 m. If the GMR of
D. 120 + j10 kohm and 19.95 + j132 ohm the ACSR conductors is 0.0466 ft, find the
46. A capacitor of 2 microfarad is supplied from inductive reactance in ohm/km/phase of the
a source voltage 2 sin 2pi106 t volts transmission line?
instantaneous value. What is the maximum A. 0.3775✓ C. 0.3628
value of current? B. 0.3398 D. 0.3964
A. 251.3 C. 0.2513 55. A 115-kV three-phase transposed transmission
B. 2.513 D. 25.13✓ line is composed of two ACSR 336,400 cmil,
47. The resistance 100 ohm, inductance 50 mH and 36/7 Oricle conductors per phase with
capacitance 50 Micro-farad are connected in horizontal configuration: D12 = 7 ft; D23 = 7
series and across 240 volts source. What is ft and D13 = 14 ft. The line spacing as
the resonant frequency? measured from the center of the bundled
A. 60 Hz C. 70 Hz conductors is 6 inches. The conductors have a
diameter of 0.741 inches a GMR of 0.02265 ft.
B. 100 Hz✓ D. 1 KHz Find the capacitance per phase for 20 km of
48. An induction motor is rated 240 V, 150 A and the line microfarads.
0.707 power factor. What is the size of the A. 0.2889 C. 0.2300
capacitor in kVAR which must be place in B. 0.2609✓ D. 0.2719
parallel with the circuit to improve the
power factor to 95% lagging? 56. A 75 kVA, 13.2 kV/240 V delta-wye
A. 17.1✓ C. 41.9 distribution transformer has a resistance of
B. 24.3 D. 26.9 1% pu and reactance of 8% pu. What is the
49. A transmission line cable consists of 226 transformer’s phase impedance referred to the
strands of identical copper conductor, each high voltage side?
1.255 mm in diameter. The length of the cable A. 69.70 + j557.57 ohms✓
is 10 km but because of the twist of the B. 71.09 + j558.72 ohms
strands, the actual length of each conductor C. 67.95 + j543.63 ohms
is increased by 5%. If the resistivity of the D. 70.58 + j564.54 ohms
copper is 1.72 x 10-8 ohm-meter, what is the
resistance of the cable in ohms? 57. The per phase parameters for a 60 Hz, 200 km
A. 1.08 C. 1.13 long transmission line are R = 2.07 Ω and L =
310.8 mH and C = 1.4774 µF. The transmission
B. 5.39 D. 5.66✓ line supplies a 100 MW, wye connected load at
50. A single-phase transmission line 90 km is 215 kV (line to line) and 0.9 power factor
made up of hard drawn copper 500 mils in lagging. Using nominal π model, determine the
diameter. If the resistivity of the hard sending end voltage line to line.
drawn copper at 20˚C is 1.77x10-8 ohm-meter. A. 229 kV C. 236 kV
Determine the loop resistance at 20°C . B. 243 kV✓ D. 233 kV
A. 0.1394 ohm/km✓ C. 0.546 ohm/km
B. 1.348 ohm/km D. 0.434 ohm/km 58. A short three phase transmission line with an
impedance of 2+j4 has equal sending and

PAGE 3
 CERTC REE-RTE-02
COMPLETE ENGINEERING REVIEW AND TRAINING CENTER
Rm 501, G .K. Ch ua Bld g., M. J. Cue nc o Ave. Ce bu Cit y
C o n ta c t N o. 0 91 7 -3 0 2- 8 82 4

REGISTERED ELECTRCAL ENGINEERS LICENSURE EXAMINATION

PROFESSIONALSUBJECTS www.certcreviewhub.com

receiving end voltage of 115 V. What should A. 424.4sin ( wt+90° ) ✓

be the power supplied to the load in MW if
receiving end power factor of 0.8. B. 424.4cos ( wt+90°)
A. 839.2✓ C. 622
B. 760 D. 712 C. 300sin ( wt+90°)
59. A generator of 50 MVA, 4 kV, X”d = 25% and a D. 300cos ( wt+90° )
transformer of 50 MVA, 4 kV delta/115 kV wye-
grounded operating on a 3.8 kV tap where Xt” 70. Power system has receiving current of 1.2 pu
= 10% to be connected into a single or current at the receiving end, 0.6 pu
equivalent reactance. What is the single voltage at the receiving end and 0.5 pu
equivalent reactance on a 100 MVA, 110-kV receiving power. When the base current is 160
base? amp and base voltage is 20 kV, what is the
A. j 0.7667 pu✓ C. j 0.8663 pu power factor at the receiving end?
B. j 0.6039 pu D. j 0.8241 pu A. 0.5 C. 0.8
B. 0.7 D. 0.69✓
60. A 230 volts, 3-phase system has a load of
7.07 + j 7.07 ohms both are wye connected. 71. A circuit has 125 A base current and 25 ohms
What is the current? base impedance, find the kVA base?
A. 9.39 – j 9.39✓ A. 3.125 C. 3125
B. 16.206 + j 16.206 B. 390.625✓ D. 39.063
C. 9.39 + j 9.39 72. A current is given by this equation i = 2t3 +
D. 16.206 – j 16.206 t2 + 3, a capacitor has an initial charge of
61. A circuit has impedance of 3.464 + j2.0 is 6.83 coulomb. What should be the charge in
supplied from a sourc voltage of 240 volts, coulomb of the capacitor after 5 sec?
60 Hz. What is the current when resistance is A. 362 C. 375.8✓
reduced by 50%. B. 385 D. 369
A. 91 A✓ C. 72 A 73. A single band transmitter has a voltage
B. 60 A D. 54 A supply of 230 volts. Voice peak produces a
62. A 240 volts dc shunt has an armature current current of 1.5 ampere. What is the peak
of 50 ampere, armature resistance of 0.25 envelope power?
running at 1200 rpm. If it is run at 220 A. 300 C. 460
volts, what value of armature current if the B. 322 D. 345✓
speed remains at 1200 rpm but the field is 74. An 80 cm long conductor carrying a current of
change. 3.6 ampere and seen right angle to the flux
A. 55 C. 60 density of 0.95 tesla. What is th force in
B. 50 D. 46✓ the conductor?
A. 0.2736 C. 273.6
63. An induction motor 8 poles, 60 Hz, 3% slip.
B. 27.36 D. 2.736✓
What is the rotor speed in rpm?
A. 900 C. 873✓ 75. A three phase wye connected balanced load of
B. 927 D. 847 10 ohms each resistor connected to a 220
volts source. Determine the power.
64. Two transformers each rated 100 kVA, A. 19.36 C. 9.6
13200/240 volts are connected open delta.
B. 4.84✓ D. 14.52
Determine the maximum kVA of the load.
A. 173.2✓ C. 100 76. What type of motor is used for food mixer?
B. 141.2 D. 200 A. Split phase
B. Universal
65. The illumination at a certain distance is 800 C. Shaded
lux, what is the illumination in lux when the D. Compound shunt
distance to the point is doubled?
A. 300 C. 400 77. Receptacle outlet shall be located ot more
B. 100 D. 200✓ than _____ mm above the countertop.
A. 300 C. 250
66. The net energy required of a certain country B. 450✓ D. 600
in year 2000 was approximately 3x106 GWH. What
is the equivalent value in quad? 78. A Diesel Power plant is best suited as
A. 12.42 C. 124.2 A. Base load Plant
B. 10.24✓ D. 102.4 B. Peak load Plant
C. Standby Plant✓
67. What is the required Volt-Amp for lighting of D. General purpose Plant
an ofice building with 500 sq. m area? 79. What is the minimum distance between the
A. 16,500 C. 23,500
receptacle outlets in meters of a show window
B. 14,000✓ D. 50,000 A. 3✓ C. 2
68. An ideal transformer has a voltage rating of B. 4 D. 5
240/240 volts, a motor is connected to the 80. In Philippine Distribution Code Purposes,
secondary draws 50 A at 200 volts, what which of the following is not belong?
resistance must be connected to maintain this A. To ensure quality of electric Power
voltage?
B. To specify Customers services for the
A. 0.6 C. 0.5
protection of end users
B. 0.3 D. 0.8✓ C. To specify standards for the protection of
69. The complex expression of voltage is 300 cis personnel in the work environment
90 deg. What is its instantaneous equation?
PAGE 4
 CERTC REE-RTE-02
COMPLETE ENGINEERING REVIEW AND TRAINING CENTER
Rm 501, G .K. Ch ua Bld g., M. J. Cue nc o Ave. Ce bu Cit y
C o n ta c t N o. 0 91 7 -3 0 2- 8 82 4

REGISTERED ELECTRCAL ENGINEERS LICENSURE EXAMINATION

PROFESSIONALSUBJECTS www.certcreviewhub.com

D. To ensure that distribution system will be D. Material, area and length

operated by only one distribution company✓
91. What is the spacing between receptacle
81. The resistance of conductor increases out;ets in dwelling unit
A. When length of conductor increased✓ A. 1,800 mm✓ C. 1,700 mm
B. When the resistivity of the wire remains B. 3,700 mm D. 4,000 mm
constant 92. Which of the following is not belong on
C. When the are of the wire is increased finding/searching the lightning arraters
D. When length and area of conductor are both A. Voltage rating
increased B. Current rating
C. Insulator coordination
82. In Philippine Distribution Code Power Quality D. Power rating✓
Standards, which of the following does not 93. What is the minimum ampacity of feeders w/
belong? motor and other load connected.
A. Frequency shall be constant at 60 Hz✓ A. 250% motor FL current plus other current
B. THD of the voltage shall not exceed to 5% B. 125% motor FL current plus other current✓
during normal operating condition C. 125% total current
C. The maximum voltage unbalance at the D. 250% total current
connection point of any user shall not 94. In Philippine Distribution Code Reliability
exceed to 2.5% during normal operating Standards, the following are reliability
condition indices shall be imposed except one
D. The flicker severity at the connection A. System Average Interruption Frequency
point of any user shall not exceed to 1.0 index
unit for short term or 0.8 unit for long B. System Average Interruption Duration index
term. C. Momentary Average Interruption Frequency
83. In Philippine Distribution Code System D. Momentary Average Interruption Duration✓
efficiency Standards, power Factor at the 95. Insulation of wire is based on__
connection point shall be_____? A. RMS C. Average
A. Not less than 80% B. Peak✓ D. 1.723 peak
B. Not less than 85%✓ 96. Outdoor outlets of one-family dwelling shall
C. Not less than 90% be installed not more than_____ mm above
D. Always unity grade level at the front or back of the
family dwelling
84. Which type of DC motors is not directly A. 3000 C. 2000✓
connected to the load? B. 4000 D. 1500
A. Shunt✓ C. Universal
B. Series D. Compound 97. In Philippine Distribution Code Safety
Standards for Distributions Utilities and
85. In a dc motor which one is not considered in Suppliers, the following are adopted
determining the speed? except______
A. Thickness of armature lamination✓ A. PEC Part I
B. Strength of the magnetic field B. PEC Part II
C. Strength in the armature C. OSHS
D. Load on the motor D. Building Code✓
98. In Philippine Distribution Code Performance
86. What is the device used and connected to a
Standards, which of the following is not
generator to prevent motorizing?
belong?
A. Reverse power relay✓
A. Collection Standards✓
B. Overvoltage relay
B. Reliability standards
C. Overcurrent relay
C. Safety standards
D. Directional relay
D. System efficiency standards
87. In dwelling units, at least one receptacle
outlet for hallways more than _____m. 99. What is the best conductor of electricity?
A. 3✓ C. 2 A. Polyethylene
B. 4 D. 5 B. China Clay
C. Ceramic
88. A device used for switching, carrying and D. Graphite✓
interrupting a system for both fault and full
load condition. 100. The effect of the dielectric is to
A. Sectionalizer A. Increase the capacitance
B. Fuse B. decrease the capacitance
C. Circuit breaker✓ C. Increase the working voltage
D. Air break switch D. reduce the working voltage✓
89. Which of the following is not a cause of
noise in communication system? 101. What will happen to an insulating medium if
subjected to a voltage more than its basic
A. Heat agitation of electrical component✓
impulse insulation level? It will ____
B. Manufactured electrical equipment
A. Change its molecular structure
C. Atmosphere
B. become magnetic
D. Other communication signal
90. Factor in determining specific resistance C. Punctured✓
D. melt
A. Nature of material✓
B. Material and length
C. Area

PAGE 5