Ultra excellent

Torantrieb Garage Door Electric Operator

Elektrisk Portåbner
Motorisation de porte de garage
Elektrisk mekanisme for garasjedører
Elektrische garagedeuropener
Elektrisk garageöppnare
Operatore elettrico apriporta per garage
Autotallin ovikoneisto
Napęd do bram garażowych
Kapumeghajtás

Einbau- und Bedienungsanleitung D

Instructions de montage et d’utilisation F

Handleiding voor montage en bediening NL

Istruzioni per l’installazione e l’uso I

Instrukcja montażu i obsługi PL

Szerelési és kezelési útmutató H

GB
Installation and operating instructions
DK
Installations- og betjeningsvejledning
N
Monterings- og bruksveiledning
Monterings- och bruksanvisning S

Kokoamis- ja käyttöohje FIN

 English

Table of contents EC conformity Intended application

declaration
Introduction ......................................... 57 Application according to intended
EC conformity declaration ................... 57 According to the EC machine guideline purpose
98/37/EC, we hereby declare, that the The door drive is intended for opening
Intended application ............................ 57
subsequently designated product com- and closing of single or double garage
Storage ............................................... 57 plies with the relevant basic EC guide- doors in the private sector only.
Directions, remarks ............................. 57 lines because of its design and construc- This door drive has to be equipped with
tion and in its configuration, as we put it additional safety equipment (safety strip,
Cross-references: ............................... 58 in circulation. This declaration loses its etc.) if the manufacturers basic setting
Safety .................................................. 58 validity in case of changes to the prod- for obstruction safeguard (F1 = force
uct, which are not agreed by us. down, F2 = force up) is changed or the
Installation requirements ..................... 58
Door drives are components for installa- closing automatic is activated (see page
Preparations for installation ................ 58
tion to garage doors, and are considered 61).
Tools .................................................... 58 as machines in the sense of EC machine Any use that exceeds the aforemen-
Delivery ............................................... 58 guideline 98/37/EC because of that. tioned is considered as not in accord-
Drive assembly ................................... 58 The putting into operation is prohibit- ance with the intended application. The
ed until the compliance of the final manufacturer should not be held liable
Adjusting tension of drive belt ............. 58 product with this guideline has been for damages resulting from such use.
Installation ........................................... 58 certified.
Door connection .................................. 59 Improper application
Product description It is prohibited to use the door drive for:
Putting door drive into operation ......... 59
Electromechanical garage door drive - Commercial or industrial use
Basic settings (learning of end
positions and forces) ........................... 59 - Atmospheres at risk of explosion
Manufacturer
Checking obstruction safeguard ......... 60 ABON - Garage doors with more than 3.5 m
Antriebe und Sicherheitssysteme GmbH door height
Operation ............................................ 60
Thalbach - Automatic operation
Hand-held transmitter operation ......... 60 D-85368 Wang
- Use for more than one household.
Additional settings ............................... 60 Germany
Additional safety connections ............. 62
Model Storage
Additional illumination ......................... 62 Ultra excellent
Terminal configuration ......................... 62 The door drive, whether in packaged or
Installing light disc ............................... 62 Applied relevant EC guidelines loose state, has to be stored in a closed,
EC Machine Guideline 98/37/EC dry room. The storage temperature must
Technical data ..................................... 62
EC Low Voltage Guideline (72/23/EEC) not fall below -20°C and must not ex-
Noise emission level ........................... 62 EC Guideline Electromagnetic Compati- ceed 80°C.
Indications of LED bar display ............ 63 bility (EMC) (89/336/EEC)
EC Construction Product Guideline
Self-test ............................................... 63 (89/106/EEC) Directions, remarks
Search/elimination of malfunctions ..... 64
Maintenance ....................................... 64 Applied harmonised standards Important directions and remarks are
EN 12 453, EN 12 445, EN 12 978, highlighted by:
Repair ................................................. 64 EN 55 014-1, EN 55 014-2,
Customer Service ............................... 64 EN 60 335-1:2001, CAUTION
EN 60 335-2-95:2001, EN 60 335-2-103 To be found in connection with working
Accessories ......................................... 64
or operating procedures that have to be
Spare parts ......................................... 64 observed accurately, in order to exclude
Approval
This door drive is approved according to danger to persons.
EN 60335-2-95.
Introduction This approval is valid only in case of ATTENTION
use according to its intended purpose Includes information that has to be ob-
This instruction (text part) is to be used served in order to prevent damage on
and for the drive of doors that are in-
together with the installation scheme the device.
spected according to EN 12453/ EN
(image part). Read and observe text and
12445 and listed in the annex of this
image part carefully before installation NOTE
installation and instruction manual as
and putting into operation. Stands for technical requirements that
well (01.05.2005 →)→).
Depending on which accessories have have to be particularly observed.
additionally been ordered, further in-
structions are to be observed. These are Wang, 30th June 2004
enclosed in the regarding accessory
sets.

(Hermann Leppert, Managing Director)

57
 English

Take mechanical door locking out of use.

Cross-references: Installation requirements Unpack door drive and accessories;
check completeness of delivery. Keep
In the text part cross-references to the
Only authorized electricians are packaging for returning in case of repair.
installation scheme are represented as
follows: allowed to carry out work on the elec-
trical equipment. Store packaging material (e.g.
[12] = Image number, e.g. 12. plastic) out of reach of children.
Technical knowledge and craftsmanship
[21-]= Image number, e.g. 21 and sub- are required for installation of this drive.
sequent images. For the packaging of door drive,
The installation of door drive must be only reusable materials have been used.
(21) = Position number, e.g. 21 performed in dry rooms only. Please dispose of accumulated packag-
The clearance between the garage ceil- ing material according to the country-
ing and the highest point of the opened specific regulations.
Safety
door must be at least 50 mm.
The door must be activated by horizontal
For the safety of individuals it is pulling force or pressure force. The re-
Tools
essential to observe any instruction quired pulling/pushing force must not ex-
of this instruction manual. Preserve [1] Keep displayed tool ready.
ceed 150 N.
both instructions (text part and image
part) as well as the instructions for The mounting points on ceiling, wall or
accessories close at hand for future lintel and door have to ensure a safe Delivery
use. mounting of door drive. If required, addi-
tional constructive measures (suspend- [2-3] See installation scheme (image
The door drive is designed and built ac- ed ceiling, staying, cross supports, rein- part).
cording to state of the art technology and forcements) have to be carried out.
approved safety rules. However, during
its use, hazards to persons or impair- Have an earthed socket 230 V, 50 Hz in-
ment to properties might occur. stalled about 10-50 cm beside the later Drive assembly
mounting position of the drive head. For
Unplug mains plug before beginning any constructive security see technical data. [4-14] See installation scheme (image
works at the door drive. part).
The mechanical components of the drive
Rebuilding and changes of the door should comply with standards EN 12 604
drive are not permitted for safety and and EN 12 605.
warranty reasons. Adjusting tension of drive
During installation of door drive to the
Before activating control equipment (e.g. door, compliance with standards
belt
transmitter, buttons) make sure that no EN 12 453, EN 12 445 and EN 12 635,
persons, animals or objects are in the [15-] Tighten safety nut (23) until drive
during installation of additional safety
range of movement of the door. Make belt (5) does not lie tight inside
equipment (light barrier, optical sensor,
sure that unintentional or inattentive op- the guide rail (10) and is slightly
safety strip) with the standard EN 12 978
eration, e.g. by playing children, is ex- tightened.
have to be ensured.
cluded.
In case of garages with no second ac-
If a slip-door is built-in in the garage
door, a safety device has to be installed,
cess, an external emergency button is Installation
required. It is, if required, to be ordered
which blocks operation of the door drive separately. [17-29] See installation scheme (image
as long as the slip-door is open.
ABON should not be held liable for tech- part).
Before door drive installation it has to be nical inadequacies of the door con-
checked that the door is easily moveable cerned, nor for structural deformation Support drive with suitable aids
by hand and that the door mechanics during use, as well as in case of inade- after lifting towards the ceiling and
are in working order. quate repairing of the door. secure against falling down. Inspect
The drive must not be used for unadjust- mountings at ceiling and lintel again
ed doors, because the drive construction after installation [23,24,29].
is not designed for this application. Preparations for installation
In the case of the door being equipped
with weight balancing in form of steel Wrong installation might cause
springs, their correct functioning has to serious injuries. Observe all installa-
be ensured. tion instructions of this instruction
Adjustments and repairs must be per- manual.
formed by the responsible customer
service of the doors manufacturer only – Check and adjust function and
never try this yourself (danger of injury easy operation of door before door
by springs under tension). drive installation. The spring tension
In connection with installing the door has to be adjusted in a way, that the
drive to the door, the instructions of the door can easily be opened and closed
door manufacturer have to be observed by hand and runs continuously and
too. smoothly.

58
 English

End position „DOWN“

Door connection Basic settings (learning of [38] There are two possibilities for con-
end positions and forces) firming end position „DOWN“:
Depending on the door type, there • 10 seconds after reaching the
are different installation sets available. closed position automatically or
For performing basic settings
Connect door and drive according to the • by pushing of button 3 or 4.
the door drive must be coupled with
instruction, enclosed in the installation the door. During learning there is still Once the end position „DOWN“ is
set. no protection by the safety switch-off learned, the drive lamp flashes
due to excess force. twice, subsequently the door is run
If the door cannot be coupled with automatically into opened position
the drive, the sled (4) has to be run in There are two learning again.
closing direction by means of button 2 of possibilities: Force in „UP“-direction
the transmitter or the sled has to be un- • With transmitter [38]
locked. Couple door for performing of [38] During run into end position „UP“
• Without transmitter [39-42]
learning runs [38]. If the end position the control learns the force auto-
has been activated unintentionally, the [37] Check with screwdriver by turning matically. The drive stops automati-
mains plug has to be unplugged for 2 anti-clockwise, if both potentiome- cally, once the end position „UP“ is
seconds (=reset). ters (F1 and F2) are in minimal end reached. For confirming the
position. learned force, there are two possi-
bilities:
Putting door drive into Learning with transmitter • 10 seconds after reaching the
opened position automatically or
operation • by pushing button 3 or 4.
Disassembling light disc Once the force values in „UP“-di-
[30-] Snap off light disc (1.2). rection have been saved, the drive
lamp flashes once, subsequently
[32] Remove box with transmitter (2) the door is run into closed position
and antenna (8). Snap light disc automatically.
back in after putting into operation
only [67-]. Force in „DOWN“-direction
[38] During run into end position
Control and display elements [33] „DOWN“, the control is learning the
F1 Rotary potentiometer „Force DOWN“ force automatically. The drive stops
F2 Rotary potentiometer „Force UP“ automatically, once the end posi-
1 LED (red) tion „DOWN“ is reached. At the
2 „Program“ button same time the force values in
3 „Impulse“ button Button 1: Dead man operation and fine- „DOWN“-direction are saved. 2
4 LED „Power“ (green) tuning up seconds after reaching the end po-
5 LED row display Button 2: Dead man operation and fine- sition „DOWN“, the door is auto-
P DIP switch tuning down matically run into opened position
in order to avoid locking out the fit-
Button 3: Confirmation (save) ter from the garage.
External connections [34]
Button 4: Confirmation (save)
1 Impulse
2 Partial opening End position „UP“ After finishing the above-described
3 Safety strip/light barrier learning runs, only the learned button is
[38] Activate button 1 and keep it active, see paragraph „Hand-held trans-
4 Emergency stop pushed, the door moves to open.
5 Antenna A = Antenna mitter operation“.
At the moment, where the desired
E = Earthing end position „UP“ is reached, re-
lease button 1.
Connect antenna
[35] Connect antenna (8) to the exter- A correction of end position „UP“ is
nal connection (5, left screw termi- possible by pushing button 2.
nal A).
Confirm reached end position
„UP“ by short pushing of button
Connect to mains power 3 or 4, the drive lamp flashes
[36] Plug in mains plug. The green LED 3 times. After learning end position
„Ready“ (4) must light, the drive „UP“, the door is run automatically
lamp flashes 4 times. in closing direction. The drive stops
automatically, once the right closed
Make sure that no persons, ani- position is reached.
mals or objects are in the range of
movement of the door before activat-
ing the drive.

59
 English

Learning without transmitter Force in „DOWN“-direction Learn transmitter

End position „UP“ During run into end position The topmost button of the hand-held
[39] Unlock western plug with yellow „DOWN“, the control is learning the transmitter is learned for the radio re-
bridge (3) and pull out. force automatically. The drive stops mote control by the manufacturer al-
automatically, once the end posi- ready. If you want to learn a further but-
[40] Activate „Impulse“ button (3) and ton of the transmitter or a second trans-
tion „DOWN“ is reached. At the
keep it pushed. The door moves to mitter, proceed as follows (for learning,
same time the force values in
open. Release the „Impulse“ button hold transmitter as close as possible to
„DOWN“-direction are saved. 2
as soon as the desired end posi- the drive head):
seconds after reaching the end po-
tion „UP“ is reached.
sition „DOWN“, the door is auto- [44] Push „Program“ button (2) briefly –
[41] Plug western plug (3) back in. matically run into opened position the red LED (1) flashes once: Acti-
in order to avoid locking out the fit- vate within 20 seconds a not-
A correction of end position „UP“ in ter from the garage. learned transmitter button – the red
closing direction is possible now by LED lights continuously (learning is
means of the „Impulse“ button. finished).
[42] Confirm reached end position „UP“ Checking obstruction
by pushing the „Program“ button safeguard In case of wrong learning, the radio
(2), the drive lamp flashes 3 times. commands can be reset again, see [49].
Once the end position „UP“ is The obstruction safeguard is safety For putting further hand-held transmit-
learned, the door is run automati- equipment that protects against crush- ters into operation, repeat the entire
cally in closing direction. The door ing, and should prevent injuries caused learning procedure and proceed as
drive stops automatically, if the by the closing door (static switching-off aforesaid.
right closed position is reached. force: 150 N).
End position „DOWN“ [43] Perform test run: 1-channel operation
Stop door from outside with both [45] First button is learned.
There are two possibilities for con-
firming end position „DOWN“: hands in hip height. During closing
• 10 seconds after reaching the procedure, the door has to stop au- Multi-channel operation
opened position automatically or tomatically and run back about 30 [46] 2-channel operation: learn first,
cm, if it meets resistance. During second or arbitrary button.
[42] • by pushing the „Program“ button opening procedure it has to stop
(2). [47] 3-channel operation: learn first,
automatically, if it is held back.
Once the end position „DOWN“ second, third or arbitrary button.
is learned, the drive lamp flash- After a switching off due to excess [48] 4-channel operation: learn first,
es twice, subsequently the door in force, the drive lamp flashes until the second, third and fourth button.
is run automatically back into next impulse or radio command arrives.
opened position. Reset of all learned radio com-
Force in „UP“-direction mands (if needed only)
During run into end position „UP“ Operation [49] Activate „Program“ button (2) at
the control learns the force auto- least 5 seconds long. The red LED
matically. The drive stops automat- (1) flashes then for 2 seconds
Instruct all persons, who are in- quickly and goes out – now the re-
ically, once the end position „UP“ is volved in using the door equipment,
reached. For confirming the set procedure (duration about 5
with respect to safe and proper opera- seconds) is finished. Any learned
learned force, there are two possi- tion of it.
bilities: hand-held transmitters are reset.
There is a risk of injury due to crush-
• 10 seconds after reaching the ing or cutting at the closing edges
opened position automatically or and with the mechanical device. Open Additional settings
[42] • by pushing the „Program“ button and close the door only when you can
(2). see the area of movement of the door The door drive is delivered with a manu-
Once the force values in „UP“- and when no people are in the imme- facturer basic setting, where all switches
direction have been saved, the diate vicinity! of the DIP-switch block (P) are in OFF-
drive lamp flashes once, subse- position.
quently the door is run into
closed position automatically. Hand-held transmitter
operation

Keep transmitters away from

children. Activate the hand-held trans-
mitter only, if you can see the door
area well. Watch the moving door and
keep persons away, until the door is
completely closed or opened.

60
 English

If needed, the following additional set- Adjusting pre-warning time [55] Setting automatic closure by switch
tings can be performed by means of the 5:
rotary potentiometers (F1, F2) and of the With switched on pre-warning time Run door in opened position and
DIP-switch (P): first only the drive lamp is lighting with wait as long as the door should re-
each control-device impulse, only four main open. After reaching the de-
[50] Obstruction safeguard (F1, F2)
seconds later the motor run is started sired open time, put switch 5 into
Pre-warning time (P, switch 3) (manufacturers setting: 0 seconds). ON-position, the drive lamp starts
Partial opening time (P, switch 4) [53] Adjusting pre-warning time by flashing. After 4 seconds the door
switch 3: runs into closed position. The set
Automatic closure (P, switch 5)
ON-position: 4 s time remains saved.
Lighting time (P, switch 6) OFF-position: 0 s.
Soft run in closing direction (P, In order to change a set open time,
switch 7 and 8) Adjusting partial opening switch 5 has to be put into OFF-position
The partial opening is the stretch of run, first, and then, as described before, set
Function of input safety strip/light back to ON-position. This is also re-
barrier/optical sensor (P, switch 1 after which the door stops after starting
from closed position in a partially open quired after a reset switching. The auto-
and 2). matic closure does not react in connec-
position.
tion with a partial opening.
Adjusting obstruction safeguard
The force for opening and closing the The partial opening does not work
in connection with automatic closure. Set lighting time
door can be adjusted by means of the The lighting time is the length of time
rotary potentiometers „Force down“ (F1) In order to carry out a partial opening of during that the drive light is illuminated
and „Force up“ (F2). In the manufactur- the door, either a control element (e.g. after the motor has been running. The
ers setting the force is set to minimal val- wall-fitted button) has to be connected to lighting time is freely adjustable by
ue and has normally not to be changed. the external terminal „Partial opening“ switch 6 (from 2 s to maximal 8 minutes).
With this setting a normal, smoothly (2) or the second channel of the hand- The lighting time is 2 minutes in default
moving door should run accurately; un- held transmitter has to be learned. In or- setting; switch 6 is in OFF-position.
less there is an obstacle it should not der to do that, press „Program“ button
stop or change its running direction. (2), then the „Impulse“ button (3) – LED [56] Set lighting time by switch 6: Start
2 of the LED row display flashes: Acti- motor run and move door into an
Before a setting is changed, the door end position („DOWN“ or „UP“). Af-
has to be checked for smooth run and vate a non-used button of the transmitter
(2,3, or 4) – the LED row display lights ter reaching the desired lighting
function and to be better adjusted. time, put switch 6 in ON-position
(depending on reception level up to 7
If required, the obstruction safeguard LED’s). Now the hand-held transmitter is and the set time remains saved.
can subsequently be adjusted higher, as learned correctly.
follows: In order to change a set lighting
[54] Adjusting partial opening time by
[51] Check with screwdriver in anti- time, switch 6 has to be in OFF-position
switch 4:
clockwise direction, if both rotary first, and then, as described before, has
Open door starting from closed po-
potentiometers (F1 and F2) are in to be put back into ON-position. This is
sition and with OFF-position of
minimal end position. also required after a reset switching.
switch 4 by impulse (hand-held
[52] Increase the adjustment values transmitter/control element).
with rotary potentiometers F1 and Stop the door drive with reaching Set the soft run
F2, until the door runs accurately of desired partial opening level and The soft run is a control function, by
into both end positions. The maxi- set switch into ON-position. means of which the door is run into
mal permissible values have to be closed position with reduced motor RPM.
In order to change an adjusted The duration of soft run is adjustable by
measured according to standards partial opening time, run door into closed
EN 12 453 and EN 12 445 by switches 7 and 8. The default setting is 3
position and set switch 4 into OFF-posi- seconds; both switches are in OFF-posi-
means of a suitable measuring de- tion. Readjust the partial opening time as
vice and must not be exceeded. tion.
aforesaid.
[57] Set Soft run duration by switch 7
If the manufacturers basic set- and 8:
Setting automatic closure
ting of rotary potentiometers F1 and The automatic closure is a control func- Switch 7 Switch 8 Time
F2 is changed, occurring forces of the tion, which runs the door automatically
doors closing edge have to be meas- OFF OFF Ca. 3 s
from opened position back into closed OFF ON Ca. 6 s
ured, see working step [52]. If the per- position. The closing time is freely ad-
missible values of the norm are ex- ON OFF Ca. 1.5 s
justable by switch 5 (from 2 s to maximal ON ON 0s
ceeded, additional safety equipment 8 minutes). The automatic closure is
(e.g. light barrier, optical sensor, safe- switched off in the default setting; switch After setting the soft run duration
ty strip) has to be installed and used. 5 is in OFF-position. reset the control, see [76]. Carry
out basic setting (learning runs)
subsequently; see [38].
The operation with automatic
closure is permitted only if additional
safety equipment (light barrier/optical
sensor/safety strip) is installed [58-].

61
 English

Change drive direction

Additional safety Technical data
connections Changing the drive direction is re-
quired for double-doors and, if neces- Mains supply .................... 230 V~, 50 Hz
[58] In delivery state, there are bridged sary, for lateral-sliding doors.
Device fuse, internal ........ 1,6 A, T (slow)
western plugs (4=green, 3=yellow) [63] Unlock western plug with green
Operational force .......................... 800 N
plugged into the external terminals bridge and pull off.
„Emergency stop“ (4) and „Safety Nominal load ................................. 240 N
[64] Activate the „Program“ button (2)
strip/optical sensor/light barrier“ once. Push „Impulse“ button (3) six Power consumption with
(3). times; the red LED 7 of the LED nominal load ................................ 170 W
row display flashes. Activate „Pro- Idle current (Stand-by) ..................... 4 W
Terminal „Safety strip/optical sen- gram“ button (2) once again, the
sor/light barrier“ (3) drive direction is changed and the Protection class ........ For dry rooms only
A safety device (safety strip, optical sen- control is reset. Speed with nominal load ...... > 100 mm/s
sor or light barrier) can be connected to [65] Plug western plug with green Run time limit ................................... 80 s
this input terminal: bridge (4) back in again. Max. stroke ............................... 2540 mm
[59] Unlock western plug with yellow Carry out basic settings (perform
bridge (3), pull out and store. In- Flush height ................................. 35 mm
learning runs); see [38].
stall safety device and connect by Radio control ............................. 433 MHz
means of western plug.
The set change in drive direction Permissible ambient
[60] Select function of safety device by remains active after a control reset too. temperature ................ -20 °C bis + 50 °C
switch 1 and 2:
Hand-held transmitter range* ... 15 - 50 m
Safety Switch 1 Switch 2
device Additional illumination Illumination ............................ max. 40 W

Light barrier input OFF OFF Transmitter battery ........... 12 V, Typ 23 A

Safety strip with ON OFF Only a qualified electrician may Obstruction safety device setting .. 150 N
8.2 kOhm-resistor perform the connection of an addi- Max. number of cycles per hour
tional illumination. (with nom. load) .................................. 20
Optical safety strip ON ON
(optical sensor) In addition to the drive light (40 W) an Max. number of cycles per hour
additional illumination of max. 60 W (no without interrupt (with nom. load) .......... 8
(Not permissible (OFF) (ON) fluorescent tube or energy saving lamp)
setting) might be connected. * The hand-held transmitter range might
be significantly reduced by external dis-
[66] Connect additional lamp parallel to turbances under certain circumstances.
Check the function: If the installed drive light at terminals 1 and 2
safety device is activated during (light).
door closure, the door has to stop
and run back completely. Noise emission level
[66] Terminal configuration Topmost noise pressure level: <70db (A)
Terminal „Emergency stop“ (4)
An emergency stop device (slip-door Terminals 1-6 and 10-18 of the controls
safety device or emergency pushbutton) terminal strip are connected by default
can be connected to this input: (=standard connection).
[61] Unlock western plug with green Terminal Add. Connection
bridge (4), pull off and store.
8 Warning light 230V,
[62] Install emergency device and con- AC, L-switched, fused
nect by means of western plug.
9 Warning light 230V, AC, N
Checking function: If the emergen-
cy-stop device is activated during 19 Zero potential
door run, the motor has to stop im- 20 Antenna
mediately.

Installing light disc

[67-] Snap in light disc (1.2) [67-70].

62
 English

Indications of LED bar dis-

play
[71] On the control a LED row display is Press Press Flashing Function Press
arranged that consists of the light „Program“ „Impulse“ of LED transmitter
emitting diodes 1 to 8. The LED button button nr. button
row display is used for indication of 1x - 1 Learning transmitter 1x
- The radio signal level
- Interfering frequencies 1x 1x 2 Partial opening 1x
- Motor current measurement 1x 2x 3 Only upwards run 1x
- Programming and
1x 3x 4 Only downwards run 1x
- Error analysis.
1x 4x 5 Light ON/OFF 1x
Radio signal level indication, inter- 1x 6x 7 Change of drive direction -
fering frequencies
In idle state the LED row display shows
the radio signal level. Interfering fre- The function „Change of drive direction“ is possible only with disconnected
quencies, which can affect the radio re- western plug (4, green) [72] and has to be confirmed by pressing the „Program“ but-
ception and reduce the range of the ton once more. If during the programming phase no button is pressed within 15 sec-
hand-held transmitter, are displayed by onds, the menu is left automatically. The hand-held transmitter buttons, which have
lighting up of one or more (maximal 7) to be learned, are freely selectable.
LED’s, beginning each time with LED 1.

Motor current measurement

The force that is required during motor
run is displayed by the LED row display.
If all light emitting diodes light, the motor
current and the used force are at its
maximum.

Programming
By pushing the „Program“ button, the
programming mode is initiated. Depend-
ing on whether and how often the „Im-
pulse“ button is pressed subsequently,
different functions are achievable. The
light emitting diodes of the LED row dis-
play indicate in this case, which func-
tions are executed:

Self-test
A control self-test is performed Drive-monitoring and indication of malfunctions by LED row display
- After switching on (switching-on test)
- After each motor run
Indication Cause of malfunction
- Every 2.25 hours in idle state.
LED 2 OFF Malfunction in main memory
If all 8 LED’s of the LED row display light
LED 3 OFF Motor current exceeded permissible values
during self-test, then there is no malfunc-
tion. LED 4 OFF Safety output of control defective
Malfunctions, which have been detected LED 5 OFF Thyristor measurement values not permissible
during self-test, are indicated by going LED 6 OFF Motor-relays measurement values impermissible.
out of individual light emitting diodes or
the entire LED row display or in case of LED 7 OFF Failure in program run
switching off due to excess force by LED 8 OFF Malfunction in memory for learned values
flashing of the drive lamp; see the follow-
ing tables.
Troubleshooting
A control blocking (no command ac-
Reset electronic control and subsequently perform basic settings again. If the mal-
knowledgment) is initiated only, if 2 sub-
function reoccurs, call customer service.
sequent tests have detected the same
malfunction.
In case of a blockage the entire self -test
is performed again after about 1 minute.
If then no malfunction is detected, the
blocking is released automatically.

63
 English

• Snap off light disc (1.2) and remove

Search/elimination of Maintenance [30-32].
malfunctions • Unscrew screw (4) and pull out inser-
Monthly: tion module (5).
Only qualified electricians may • Check obstruction safeguard: The • Snap off lid (7) sideways and remove
carry out work on the electrical equip- drive direction must change if the it.
ment. Disconnect mains plug before door closing edge meets a 50mm • Pull defective fuse (1) out of fuse
removing drive cover. high obstacle that stands on the holder (2) and replace it. Observe the
ground. fuse value!
Drive does not run at all:
• Check mountings of the door drive at • Snap lid back in.
1. Check fuses of the building
ceiling and wall.
2. Check fuse of motor control • Fix insertion module.
• Check emergency stop for function.
3. Are the bridged western plugs cor- • Snap in light disc [67-70].
• Check functioning of escape door
rectly plugged in at the external termi-
safeguard (if present).
nals [73] (4=green, 3=yellow)?
4. Have mains supply checked by quali-
Customer Service
Yearly:
fied electrician. • Maintain door according to manufac- If you ask for help at any of the company
Drive runs faulty: turer data. addresses on the back, please indicate
1. Is the sled snapped in [74]? • Grease or oil joints of pushing bar. manufacturing number and model desig-
nation. You will find these data on the
2. Is the drive belt properly adjusted [75]? • Check tension of drive belt, if required type plate on the drive head.
tighten it [75].
3. Is the door step/way frozen?
4. Does the drive switch or switch off
Accessories
during run? Obstruction safeguard is Repair
activated. Check and adjust door.
Carry out basic setting [38]. [76] Reset electronic control Western plugs are required for ex-
5. Does the program run not work? Re- If the electronic control has to be reset, ternal connections on the drive head.
set electronic control into default set- proceed as follows: Accessories that can separately be or-
ting [76] and learn newly [38]. • Snap off light disc (1.2) and remove it dered are listed as follows:
Drive cannot be operated by hand- [30-32]. [80] 4-command hand-held transmitter
held transmitter: • First press „Program“ button (2), then for multiple uses
1. Does the LED on the hand-held trans- „Impulse“ button (1) simultaneously [81] 1-command hand-held transmitter
mitter flash? Renew battery [77]. for longer than 5 seconds. The red [82] Wall mounting for hand-held trans-
LED (3) flashes first and goes out af- mitter
2. Does the red LED (1) on the drive
terwards – the reset is finished.
head not light during activation of [83] Wall-fit button
hand-held transmitter? Reset learned
radio commands [49] and newly learn The learnt stretches for the soft run [84] Key turn button
hand-held transmitter [44] once more. and the current value that initiates the
[85] Code button
switch-off due to excess in force are de-
3. Reception level too low: Check anten- leted by reset. The learned radio com- [86] External antenna
na connection, if necessary, install ex- mands remain saved. [87] Light barrier
ternal antenna [86].
• Carry out basic settings (learning [88] Optical sensor
Drive cannot be operated by the wall- runs).
fitted button: [89] External emergency unlocking
• Snap in light disc [67-70]. device
Check wall-fitted button and control lead.
[90] Internal emergency unlocking
Obstruction safeguard does not work: [77] Replace battery of hand-held device
Reset electronic control and subse- transmitter
• Take off case lid (2). [91] Safety strip
quently carry out basic settings (learning
runs) [38]. • Remove battery (1) and replace it.
Spare parts
Malfunction during self-test: Use leak proof batteries only. Make
If a malfunction occurs during self-test, sure that the polarity is correct while in- [92] See list of spare parts in installa-
the control blocks and after 60 seconds serting. Dispose of old battery environ- tion scheme (image part).
another self-test is performed. If a mal- mental-friendly.
function is also detected during repeated Spare parts have to comply with techni-
• Push case lid back in place. cal requirements, which are defined by
test, the control is reset and remains
blocked. the manufacturer. Only with original
[78] Replace light bulb spare parts this is always ensured.
If the control is blocked during self-test
due to a detected malfunction, the elec- In case of purchase orders the item
Disconnect mains plug.
tronic control has to be reset and the ba- number has to be indicated.
sic settings have to be performed once [79] Replace fuse
again. If the malfunction occurs again, Spare parts, which are marked
the control has to be exchanged by qual- Disconnect mains plug. with „*“, may be replaced by author-
ified specialists. ized specialists only.

64