Scribd
Upload
11 views4 pages

IOT-5 Batra

Cn lab

Uploaded by

The Trading Freak
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
11 views4 pages

IOT-5 Batra

Cn lab

Uploaded by

The Trading Freak
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

DEPARTMENT OF

COMPUTER SCIENCE & ENGINEERING

Experiment 2.1
Student Name: Ankit UID: 22BCS13530
Branch: BE-CSE Section/Group: IOT_615/B
Semester: 05 Date of Performance: 22/08/24
Subject Name: IOT Subject Code: 22CSP-329

1. Aim:
To Design a weather station by checking Air quality of an environment with the
help of IoT.

2. Objective:
1. Learn about interfacing.
2. Learn about IoT programming.

3. Hardware Required:
1. Arduino Uno R3
2. MQ 135 Air Quality Sensor Module
3. Male to Female Jumper Wire
4. Software: Arduino IDE

4. Procedure:

1. Set Up the Breadboard and Arduino:

• Place the Arduino Uno on your workspace.


• Connect the GND (Ground) pin from the Arduino to the GND rail
on the breadboard using a jumper wire.
• Connect the 5V pin from the Arduino to the power rail on the
breadboard using another jumper wire.
2. Connect the MQ2 Gas Sensor:

• Insert the MQ2 gas sensor onto the breadboard.

1|22BCS13530
DEPARTMENT OF
COMPUTER SCIENCE & ENGINEERING

• Connect the VCC (Power) pin of the MQ2 sensor to the 5V power
rail on the breadboard.
• Connect the GND (Ground) pin of the MQ2 sensor to the GND rail
on the breadboard.
• Connect the AO (Analog Output) pin of the MQ2 sensor to the A0
pin on the Arduino using a jumper wire.
3. Connect the LED:

• Insert the LED onto the breadboard, with the anode (longer leg)
connected to one row and the cathode (shorter leg) to another.
• Place a 220Ω resistor between the anode of the LED and digital
pin 13 on the Arduino using a jumper wire.
• Connect the cathode of the LED to the GND rail on the
breadboard.
4. Connect the Buzzer:

• Place the buzzer on the breadboard.


• Connect the positive (longer leg) of the buzzer to digital pin 12 on
the Arduino.
• Connect the negative (shorter leg) of the buzzer to the GND rail on
the breadboard.
5. Power and Test the Circuit:

• Once all connections are made, connect the Arduino to your


computer using a USB cable.
• Upload the provided code to the Arduino using the Arduino IDE.
• Observe the LED and buzzer operation based on the gas sensor
readings. If the sensor value exceeds the threshold, the LED will
light up and the buzzer will sound.

2|22BCS13530
DEPARTMENT OF
COMPUTER SCIENCE & ENGINEERING

6. Code:
int LED = 6;
int MQ2pin = A0;
int buzzerPin = 7;

void setup() {
Serial.begin(9600);
pinMode(LED, OUTPUT);
pinMode(buzzerPin, OUTPUT);
digitalWrite(LED, LOW);
digitalWrite(buzzerPin, LOW);
}
void loop() {
float sensorValue = analogRead(MQ2pin);
if (sensorValue >= 100) {
digitalWrite(LED, HIGH);
digitalWrite(buzzerPin, HIGH);
} else {
digitalWrite(LED, LOW);
digitalWrite(buzzerPin, LOW);
}
Serial.print("Sensor Value: ");
Serial.println(sensorValue);
delay(100);
}
7. Result and Output:

3|22BCS13530
DEPARTMENT OF
COMPUTER SCIENCE & ENGINEERING

8. Learning Outcomes:

1. Sensor Calibration and Detection


2. Buzzer and LED Interfacing
3. Analog Signal Reading
4. Threshold Value Setting
5. Serial Communication Debugging

4|22BCS13530

You might also like