Scribd
Upload
4 views4 pages

QE (7th) Dec2014

QE-2014

Uploaded by

mohit.tskei
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
4 views4 pages

QE (7th) Dec2014

QE-2014

Uploaded by

mohit.tskei
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
You are on page 1/ 4
24481 B. Tech. 7th Semester (ME) Examination — December, 2014 QUALITY ENGINEERING Paper : ME-417-F Time : Three Hours ] [ Maximum Marks : 100 Before answering the questions, candidates should ensure that they have been supplied the correct and complete question paper. No complaint in this regard, will be entertained after examination. Note: Attempt five questions in all, selecting one question. from each Sections. Question No. 1 is compulsory. All questions carry equal marks, 1. Attempt all the 10 questions : 2x 10=20 (i) -Define the concept of Quality. (ii) What are the benefits of quality control ? (iii) Average outgoing quality. (iv) Define the inspection. 24481-3,650-(P-4)(Q-9)(14) P.T.O. (v) Explain the difference between binomial and passion distribution. (vi) What do you mean by TQM ? (vii) Define quality circles. (viii)What are the 7QC tools ? (ix) Explain briefly TQC. (x). What are the Objectives of the control charts ? ” SECTION-A 2. What do you mean by quality ? Explain its importance and different factors affected quality of a product. 20 3. Write short notes on : (a) Explain the terms ‘quality’ and ‘quality control’. How does . quality control differ from conventional inspection ? 10 (b) Explain the difference between quality control and quality improvement. 10 SECTION -B 4. (a) Explain the difference in interpretation: between an observation falling below the lower control limit on.an X-bar chart and one falling below the lower control limit on an R-chart. Discuss the impact of each on the revision of control charts. 10 24481-3,650-(P-4)(Q-9)(14) (2) (b) Explain some causes that would make the control chart pattern follow a gradually increasing trend. 10 5. Determine the control limit for X and R chart if EX = 357.50, ER = 9.90, number of subgroups = 20. It is given that A2 = 0.18, D3 = 0.41 and D4 = 1.59. The following are the X-bar and R-values of 4 subgroups of readings : X-bar = 10.2, 12.1, 10.8 and 10.9, R= 1.1, 1.3, 0.9 and 0.8. The specification limits for the components are 10.7 + 0.2. Establish the control limits for X-bar and R-charts. Will the product able to meet it specification ? Given : 20 (a) A2 (factor for X-bar chart) = 0.58 (b) D4 (factor for R chart) = 2.11 (c) D3 (factor for R chart) = 0.00 SECTION —C 6. A manufacturer of pins knows that on an average 5% of his product is defective. He sells pins in a packet of 100 and grantees that not more than 5 pins will be defective. What is the probability that a packet will meet the guaranteed quality ? Given e~ = 0.0067. Use passions distribution,” 20 7. Write short notes on : 20 (i) Explain the terms AOQ and: AOQL. for single sampling and double sampling plans. 24481-3,650-(P-4)(Q-9)(14) (3) P.T.O. (ii) What are the advantages and disadvantages: of variable sampling plans over those for attributes ? SECTION -D 8. What do you mean TQM and explain its element and scope of manufacturing industries ? 20 9. Explain any four: © 4x5 (i) Quality Manual. (ii) Zero defect. © (iii) Lean manufacturing system. (iv) Kaizen. (v) Kanban system. 24481-3,650-(P-4)(Q-9)(14) (4)

You might also like