Dr.

Fixit All Seal

BUILDING REPAIRS
H I G H S T R E N G T H S i B O N D P O LY M E R F O R B E S T
I N C L A S S WAT E R P R O O F I N G

Description
Dr. Fixit All Seal is based on modified co-polymer enriched with special additive designed for cementitious
composition. When added as a polymer, It offers excellent workability, uniform coating, stable slurry dispersion,
easier and faster application resulting best waterproofing properties..

307 Dr. Fixit All Seal

Typical Application
} Waterproofing – Sunken portion of bathrooms and toilets, balconies, exposed roof before finished screed.
} Concrete Repair – Spalled concrete, repairing of beam and pre-cast slab, chajjas etc.
} Plaster Repair – Repairing plaster or making waterproof screed which is better than normal plaster.
} Bond Coat – For bonding old concrete to new concrete, plaster, brick masonry.

Feature & Benefits

} High strength Si Bond polymer – Bonds strongly to concrete, masonry, stonework, plasters, cementitious surfaces.
} Shrinkage/crack control – High flexural / tensile strength to control cracking.
} Enhanced Rheology : Enables roller application , leading to time saving with easy and faster application
} Mortar modifier – Homogeneous fresh mix, easy to apply and place.
} Cracking / Shrinkage – Reduced shrinkage and cracking tendency.
} Repairs - Overall very high strength and durability.
} Easy to identify: Inherent characteristic of polymer, no spot can be left untreated
} Excellent dispersion of cement particles : It covers the surface evenly and forms uniform polymer rich coating.

Method of Application
1 S U R FAC E P R E PA R AT I O N
} Clean the surface with wire brush or scrubber to remove hidden dirt, loose particles, laitance & dust. Degrease
the surface by using suitable solvents.
} Repair the spalled concrete portion by saw, cutting the extreme edges of the repair location to a depth of at
least 10 mm to avoid featheredging & to provide strong bond.
} Clean the concrete surface to remove any contamination, where breaking is not possible, roughen the surface
by light scrabbling or grit blasting.
} For priming of concrete substrate, the surface should be thoroughly saturated with potable water. Remove any
excess of water prior to application.
2 WAT E R P R O O F I N G COAT I N G
} For a waterproofing coating Mix Dr. Fixit All Seal: Cement in the ratio 1:1 by volume.
} Mix for 2-3 minutes to avoid air entrapment. Keep on slowly adding cement to Dr. Fixit All Seal until lump free
required consistency is achieved.
} Apply 2 coats of the slurry by roller or brush on the prepared concrete substrate in the interval of 4-6 hours
between the coats and allow it to cure.
} Overlay the coating with a protective screed to the desired slope & thickness.
3 B O N D COAT
} To prepare the bond coat, mix Dr. Fixit All Seal : Cement in the ratio 1:0.5 by volume.
} Mix for 2-3 minutes to avoid air entrapment. Keep on slowly adding cement to Dr. Fixit All Seal until lump free
required consistency is achieved.
} Apply 1 coats of the slurry by roller or brush on the prepared concrete substrate.
} Ensure to overlay the repair mortar when the bond coat is still tacky.
307-09/09/22
125
 BUILDING REPAIRS

4 R E PA I R M O R TA R S & R E N D E R S
} A suitable mix ratio for patching repair mortar or render is as follows:
} Mix design - Portland Cement: 50 kg, graded quartz sand: 150 kg, Dr. Fixit All Seal : 3-4 Kg & Water: 12 - 15 litres
} Adequate moist curing shall be carried out for a week.
307 Dr. Fixit All Seal

5 F LO O R S C R E E D S & P CC
} Mix design - Portland Cement: 50 kg, Washed sand: 75 kg, 6 mm downsize aggregates: 75 kg, Dr. Fixit All Seal :
4-5 Kg & Water: 10 - 12 litres.
M I X I N G & A P P L I C AT I O N
} A forced action mixer is essential (PAN Mixer) & recommended to ensure that Dr. Fixit All Seal is thoroughly
mixed. Use a suitable sized drum with heavy-duty electrical drill machine fitted with spiral paddle mixer at slow
speed of 400-500 rpm.
} Charge the mixer with required quantity of clean & dry sand (or coarse aggregates as needed), cement & mix for
1-2 minutes, then add the recommended dosage of Dr. Fixit All Seal dispensed in water which is pre-batched. Mix
for 2-3 minutes to avoid air entrapment. Keep on slowly adding water until the required consistency is achieved.
CURING
As soon as the Dr. Fixit All Seal modified mortar and screed achieves its final set, adequate moist curing shall be
carried out for a week. Water sprinkling, ponding or the use of a non-degradable type of curing compound may be
used.

Precautions & Limitations

} Recommended dosage to be followed to achieve desired results.
} When working in hot temperature conditions, extra water may be added to the repair mortar to compensate for
the evaporation loss & make the mortar workable.
} All surfaces including edges must be primed.
} All applications should be wet on wet; the primer must not be allowed to dry. The level of added water in the mix
designs may need adjusting to achieve the required consistency.
} In general water content should be kept to the minimum necessary.
} For consistent performance the use of clean, dry sand is recommended. Where wet sand is used, reduce the
added water level as appropriate.
} Protect uncured mortar from frost. Do not retemper mortar or primer after initial set.
} Application to be carried out from 10 degC to max 40 degC.

Technical Information
PROPERTIES RESULTS
Nature type Bluish, Polymer
Total solids % by mass @ 1050C 45.0 - 48.0
Relative density ~1.01
pH 7.0 - 10.0
Coverage 2.0-2.4 m2/Kg
(All Seal: Cement in 1:1 ratio) in 2 coats, as a
waterproofing slurry coat
126
 BUILDING REPAIRS
Theoretical Coverage & Dosage
} For Waterproofing – Dr. Fixit Allseal : Cement in the ratio of 1:1 by Volume in two coats to give a coverage of
2.0 to 2.4 m2/Kg based on the surface condition.
} For Bond Coat - Dr. Fixit Allseal : Cement in the ratio of 1:0.5 by Volume
For Repair Mortars & Renders – 3 to 4 kg of Dr. Fixit Allseal per bag of cement

307 Dr. Fixit All Seal

}

Packing
1 kg, 5 kg, 10 kg, 20 kg

Shelf Life
} Best before 2 years from the date manufacture when in sealed pack and stored under proper condition.
} Store in a cool & dry place in unopened condition away from direct sunlight.

Health and Safety

} Cementitious mortars & slurries modified with Dr. Fixit All Seal when mixed or when become damp, may release
alkali which can be harmful to skin & eye.
} Wear suitable protective clothing, gloves, eye protection and respiratory protective equipment during
application.
} In case of contact with skin, rinse with plenty of clean water and then cleanse with soap water.
} In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice.

Other Products Categories available

Dr. Fixit brings you the widest range of Construction Chemicals

Pidilite Industries Limited DISCLAIMER The product information & application details given by the company
Construction Chemicals Division & its agents has been provided in good faith & meant to serve only as a general
guideline during usage. Users are advised to carry out tests & take trials to ensure on
Ramkrishna Mandir Road, Post Box No. 17411
the suitability of products meeting their requirement prior to full scale usage of our
Andheri (E) Mumbai 400059 INDIA
products. Since the correct identification of the problems, quality of other materials
Tel +91-22-2835 7000 • Fax +91-22-2835 7008 used and the on-site workmanship are factors beyond our control, there are no
www.drfixit.co.in • [email protected] expressed or implied guarantee / warranty as to the results obtained. The company
Dr. Fixit Advice Centre (Toll Free No.) 1800 209 5504 does not assume any liability or consequential damage for unsatisfactory results,
127

arising from the use of our products.