INSTALLATION INSTRUCTIONS

mpower® LED EXTERIOR LIGHT BAR

mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar

IMPORTANT NOTICE TO INSTALLER:

• Make sure to read and understand all instructions and warnings before proceeding with the installation of this product.
Ensure that the manual and any warning cards are delivered to the end user of this equipment. Proper installation of the
lightbar requires the installer to have a thorough knowledge of automotive electronics, systems, and procedures.
• Lightbars provide an essential function of an effective visual warning system. The use of the lightbar does not insure
that all drivers can or will abide by or react to an emergency warning signal, especially at high rates of speeds or long
distances. The operator of the vehicle must never take the right of way for granted and it is the operator’s responsibility
to proceed safely.
• The effectiveness of the lightbar is highly dependent on the correct mounting and wiring. The installer must read and
follow the manufacturer’s installation instructions and warnings in the manual. The vehicle operator should verify daily that
the lightbar is securely fastened to the vehicle and properly functioning before operating vehicle.
• The lightbar is intended for use by authorized personnel only. It is the user’s responsibility to ensure they understand and
operate the emergency warning devices in compliance with the applicable city, state and federal laws and regulations.
SoundOff Signal assumes no liability for any loss resulting from the use of this warning device.

! WARNING
• This product contains high intensity LED devices to prevent eye damage, DO NOT stare into the light beam at close range.

IMPORTANT INFORMATION:
• To view the full Software Revision History click the in the lower left hand corner of the SoundOff Central Lightbar
application.
• Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be
used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance.
• DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to your vehicle Owner’s Manual for
the location of any air bag deployment zones.
• DO NOT connect this device to a strobe power supply. This product is self-contained and does not require an external
power supply.

! WARNING
• Route wires only in locations that are not subject to potential wear. Make sure to avoid routing wires in the deployment
area of your airbag. Refer to your vehicle's owner's manual for airbag deployment zone.
• All customer supplied power wires connecting to the positive (+) or negative (-) battery terminal or local chassis ground (-)
must be sized to supply at least 125% of the maximum current and properly fused at the power source with appropriately
rated fuse.

NOTICE:
• Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning
devices.
• Improper use or installation may void warranty coverage.
• To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at
www.soundoffsignal.com/tech-services/returns/.
• If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at
1.800.338.7337 (press #4).
• Questions or comments that do not require immediate attention may be emailed to [email protected].

2 1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar

Table of Contents
Components/Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Module, Technical & Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Light Bar Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Fixed Height Brackets and Hook Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 7

Wind Deflector Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Function Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Electrical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 17

Wire Function Defaults / Break out Box (BOB) . . . . . . . . . . . . . . . . . . . . . . . . . 18

Connection of Breakout Box to SoundOff Signal Sirens . . . . . . . . . . . . . . . . . . . . 19

Siren Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Photo Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

LED Module Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Module Location ID's . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Replacement Parts & Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

mPower Lightbar Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Warranty & Return Goods Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3 1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar
CONTENTS
QTY COMPONENT

1 mpower Exterior Light Bar built to your specifications

OPTIONAL MOUNTING HARDWARE* OPTIONAL CONTROL EQUIPMENT

1 Vehicle Specific Hook Kit / Hardware Breakout Box Breakout Box
COMPONENTS LIN (Standard) CAN System
2 Fixed Height Mounting Brackets w/ Hardware Qty. Qty.
3 Flat Mount Hardware Kit Universal BOB (LIN) 1 0
4 Headache Brackets w/ Hardware Universal BOB (CAN) 0 1
*Components and Mounting Hardware will vary with each 24 Pin Harness 1 1
Lightbar depending on vehicle specified on order form. 4 Pin Harness 1 1
5 Pin Harness 0 1

TECHNICAL SPECIFICATIONS
INPUT VOLTAGE RANGE 10-32 Vdc
OPERATING TEMPERATURE -40˚C to +65˚C (-40˚F to +149˚F)
Reverse Polarity, Transient Voltage, Over-Voltage,
ELECTRICAL PROTECTION High-Temperature Thermal Fold-back
MATERIAL Top Cover: Aluminum Alloy / LED Modules: Dow Corning Silicone Lens

Power Cable: 15ft, 10AWG Wires, (+) RED, (-) BLACK, Data Line: 22AWG GREEN
WIRING Power Cable: 25ft, 8AWG Wires, (+) RED, (-) BLACK, Data Line: 22AWG GREEN

STANDBY CURRENT (Per Module) IGNITION ON: 0.20 Amps, IGNITION OFF: <8.5 mA
STANDBY POWER (Per Module) IGNITION ON: 2.560 Watts, IGNITION OFF: 0.108 Watts

CURRENT / POWER(Per Module) CURRENT DRAW POWER CONSUMPTION

Flashing 1.14 Amps 14.6 Watts

@12Vdc
Peak 1.9 Amps 24.3 Watts
OVERALL DIMENSIONS DEPTH HEIGHT # OF INBOARDS

48" (48.2”/ 122.4 cm) 10.6" (26.9 cm) 1.1" (2.8 cm) 12
55" (54.5” / 138.4 cm) 10.6" (26.9 cm) 1.1" (2.8 cm) 14

6": 6 & 8 LED Single Color, 12 LED Dual & 18 LED Tri Color Inboard Module
INPUT VOLTAGE RANGE: 10-16Vdc
CURRENT DRAW: 0.69 Amps @ 12.8 Vdc (Flashing Red)
1.16 Amps @ 12.8 Vdc (Peak Red)
0.87 Amps @ 12.8 Vdc (Flashing Amber, Blue, Green, White)
1.45 Amps @ 12.8 Vdc (Peak Amber, Blue, Green, White)
WATTAGE: 4.6W (Red)
7.7W (Amber, Blue, Green, White)

3": 4 LED Single Color, 8 LED Single Color, 8 LED Dual Color, 12 LED Tri Color
INPUT VOLTAGE RANGE: 10-16Vdc
CURRENT DRAW: 0.26 Amps @ 12.8 Vdc (Flashing Red)
0.62 Amps @ 12.8 Vdc (Peak Red)
0.38 Amps @ 12.8 Vdc (Flashing Amber, Blue, Green, White)
0.90 Amps @ 12.8 Vdc (Peak Amber, Blue, Green, White)
WATTAGE: 3.3W (Red)
4.9W (Amber, Blue, Green, White)

CERTIFICATION APPLICABLE COLORS

SAE J595 / J845 Class 1 RED, AMBER, BLUE, WHITE
CALIFORNIA TITLE 13, Class B RED, AMBER, BLUE
FLASHING = AVERAGE

4
STEADY ON (100%) = PEAK

1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar
Unpack Lightbar Tools Required for Installation
1. Remove light bar from box and packaging. • 7/16“ Socket with ratchet
2. Save packaging for later shipping. • Phillips Head Screwdriver
3. Check components/contents. • Drill bit #30
4. Please reference these instructions for proper wiring and installation. • 5/32 Hex Drive or Allen Wrench

TOP VIEW WITH COVER ON AUTO DIM LENS

INBOARD MODULES CORNER MODULES

TOP VIEW WITH COVER OFF*

FRONT OF LIGHTBAR

BACK OF LIGHTBAR
BOTTOM VIEW WIRE EXIT

5
*48" lightbar pictured

1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar

FIXED HEIGHT BRACKETS AND HOOK MOUNTING (PURSUIT)

1. Attach the supplied screws to the mounting foot to 7. Tighten the hook bracket bolts, torque details below:
secure the rubber pad as shown in Figure 2. Be sure
the torque does not exceed 10 IN-LBS. Due to different vehicle construction and mounting
2. Insert the 2 plastic washers inside holes of the provided locations, the torque levels for connecting hooks to the
hook brackets. lightbar foot may be different based on the vehicle.
A. Minimum requirement for torque should be
3. Keeping the lightbar level with the road, attach
10 IN/LB, with a maximum level of 45 IN/LB.*
Mounting Feet to the roof of the vehicle using the 4
B. When installing the bolts connecting the
supplied bolts. If the lightbar needs to be leveled, a
1.5° wedge can be used (PNFLBWGKT1). hook to the lightbar foot, monitor both the
lightbar and roof of the vehicle.
4. Place lightbar centered on the roof, and hold brackets C. Tighten to ensure there is no movement of
up to the lightbar. A 1/4" to 1/2" gap should be the lightbar or foot by ensuring there is no
between the hook bracket and front wall of the movement either side to side, or front to rear
mounting foot prior to putting any tension on the hook after the torque has been done.
bracket bolt (See Figure 3). Adjust the mounting foot The lightbar must be securely mounted to the vehicle for
position to accommodate for this gap. safe operation.
5. Tighten 4 ¼-20 bolts with lock washers to secure the
*Deflection of the lightbar and/or the roof of the vehicle
mounting foot to light bar with a max torque between may occur when torquing the bolts connecting the hook
30-45 inch/lbs with 5/32 hex driver or allen wrench. to the lightbar foot. Any deflection should be kept at a
DO NOT OVER-TIGHTEN! minimum to avoid damage to the lightbar or vehicle.
6. Using the holes in the hook bracket as a template,
drill 4 holes in the roof using the appropriate size drill.
Secure hook bracket to roof with 4 screws on each side. NOTE: As always, it is recommended to check the
integrity of mounted lightbars on a daily basis
to ensure secure attachment to the vehicle for
continued safe operation.
8. Insert the retainer plates over the 2 bolts on each of
! W ARNING the hook kit brackets. Screw in the retainer plate to the
hook kit bracket using the 8-32 bolts.
Route wires only in locations that are not subjected to
potential wear. Ma ke sure to avoid routing wires in the 9. Install the cover door over the hook bracket bolt to
deployment area of your air ba g. Refer to your vehicle’s finish the assembly. Place tab of one side into place
owner’s manual for airbag deployment zone. and then push the second tab into place with a flathead
screw driver.

Metal Nut
Bracket Hook Bracket
Cover Door
Plastic Washer x2

Figure 1.
Mounting
Foot
1/2" Gap Required
Flat Washer
Washer
Hook Bracket Bolt
Rubber Pad Hook Bracket

Screws 4x
Figure 3. Lock Washer

1/4-20 Bolt

6 1.800.338.7337 / www.soundoffsignal.com
Figure 2.
mPower® Exterior Light Bar English
00KPJL 0924 REV F
mpower® Exterior Light Bar

FIXED HEIGHT BRACKETS AND HOOK MOUNTING (NON-PURSUIT)

7. Due to different vehicle construction and mounting
1. Attach the supplied screws to the mounting foot to locations, the torque levels for connecting hooks to
secure the rubber pad as shown in Figure 3. Be sure the lightbar foot may be different based on the vehicle.
the torque does not exceed 10 IN-LB. Minimum requirement for torque should be 10 IN/ LB,
2. Insert the 1 plastic washer inside holes of the provided with a maximum level of 45 IN/LB. Deflection of the
hook brackets. lightbar and/or the roof of the vehicle may occur when
torquing the bolts connecting the hook to the lightbar
3. Keeping the lightbar level to the road, attach mounting
foot. When installing the bolts connecting the hook
feet to the roof of the vehicle using the 4 supplied
to the lightbar foot, monitor both the lightbar and
bolts.
roof of the vehicle. Any deflection should be kept at a
4. Place lightbar centered on the roof, and hold brackets minimum to avoid damage to the lightbar or vehicle.
up to the lightbar. A 1/4" to 1/2" gap should be Tighten to ensure there is no movement of the light-
between the hook bracket and front wall of the bar or foot by ensuring there is no movement either
mounting foot prior to putting any tension on the hook side to side, or front to rear after the torque has been
bracket bolt (See Figure 3). Adjust the mounting foot done. The lightbar must be securely mounted to the
position to accommodate for this gap. vehicle for safe operation. As always, it is recommended
5. Tighten 4 ¼-20 bolts with lock washers to secure the to check the integrity of mounted lightbars on a daily
mounting foot to light bar with a max torque between basis to ensure secure attachment to the vehicle for
30-45 inch/lbs with 5/32 hex driver or allen wrench. continued safe operation.
DO NOT OVER-TIGHTEN! 8. Install the cover door over the hook bracket bolt to
6. Using the holes in the hook bracket as a template, finish the assembly. Place tab of one side into place
drill 4 holes in the roof using the appropriate size drill. and then push the second tab into place with a flathead
Secure hook bracket to roof with 4 screws on each side. screw driver.

! W ARNING
Route wires only in locations that are not subjected to
potential wear. Ma ke sure to avoid routing wires in the
deployment area of your air ba g. Refer to your vehicle’s
owner’s manual for airbag deployment zone.

Hook Bracket
Metal Nut Cover Door
Bracket

Mounting Plastic
Foot Washer Flat
Washer
Figure 1. Hook Bracket Bolt

1/2" Gap Required

Rubber Pad

Washer x4
Figure 3. Hook Bracket
Lock Washer
x4 Screws 4x

Bolt x4

7
Figure 2.
1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English
00KPJL 0924 REV F
mpower® Exterior Light Bar

WIND DEFLECTOR INSTALLATION

1. Cut the “T” gasket (Item #3) to an overall length of 20.5” (shown in CONTAINS
Figure 3).
2. Cut the "T" gasket in half so each part is 10.25” (shown in Figure 4). ITEM # COMPONENT QTY
3. Measure 1/4” from the top of the gasket and 1/2” in from the side 1 WIND DEFLECTOR BRACKET 1
(Shown in Figure 5). Cut away the small piece of gasket. 2 ADHESIVE TAPE 2
PRO TIP: For best fit to the bottom of the lightbar, the bracket 3 “T” GASKET 1
should be slightly bent so the outside corners are approximately
4 #10-32 SOCKET HEAD BOLT 2
½” lower than the center of the bracket (shown in Figure 6).
This allows for best adhesion of the VHB so the corners of the 5 #10 SPLIT LOCK WASHER 2
bracket stay tight to the lightbar. The bracket must be adjusted for 6 SURFACE PREP WIPE 1
optimal fit by the installer due to packaging limitations.
7 INSTALLATION INSTRUCTIONS 1
4. Install the “T” gasket into the slots on the lower shelf of the wind
deflector bracket (Item #1) (shown in Figure 1). Figure 1.
5. Using the provided surface prep wipe (Item #6), clean the entire
surface of the wind deflector bracket and the surface of the lightbar
where the adhesive tape (Item #2) will contact. See "BOTTOM VIEW"
on page 5 to show front of bar and where to use prep wipe.
6. Cut one piece of adhesive tape in half. Remove one side of the
release liner from each half of the adhesive tape and place on the
outside edge of the wind deflector bracket. Remove one side of the
release liner from the full length adhesive tape center between the
outer edge of the bracket and bolt hole and the rear of the upper
step (shown in Figure 7).
7. The “T” gasket will go towards the front of the lightbar with the
adhesive tape towards the bottom of the light bar. Remove the
release liner on the tape. Holding the wind deflector bracket above
the lightbar, align the bolt holes in the wind deflector bracket with
the mounting holes in the mpower lightbar. Stick the bracket to the
bottom of the lightbar.
8. Install the provided bolts (Item #4) and split lock washer (Item #5) to
the wind deflector bracket. Tighten bolts until the split lock washer
flattens out (shown in Figure 2). Figure 2.

20.5"
Figure 3.

10.25" 10.25"
Figure 4.

0.5"

1/4"
Figure 5.

Figure 6. 0.5"

Figure 7.

8 1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar

FUNCTION DEFINITIONS
Mode Select: The mpower Exterior Lightbar is equipped with 8 selectable pattern configuration modes. The default
input wire configuration allows for 6 modes and an additional 2 modes may be configured with the PC Application using
any available input wires. Default is Mode 1 where the Mode select input is floating. Mode 2 is in use when the input is
activated. This feature allows up to 8 completely different sets of patterns to be programmed into the Light-bar's non-
volatile memory. Once programming configuration is complete, the Mode can be changed “on-the-fly” by an activation
switch which applies voltage to the Mode input wire(s).
Cruise Mode: Allows the user to program any light group(s) to “Glow” when this feature is activated. The LED intensity is
selectable between 1 and 10% duty cycle. For dual / tri color bars, the color for each light group is selectable.
Takedown Mode: Allows the user to program any Light Head Group(s) to turn on steady when this feature is activated to
provide steady ON takedown lighting.
Directional Arrow Built-in: The directional controller is built-in with 11 arrow patterns for each of the 3 modes (left
arrow, right arrow, and center out arrow) and the color is selectable for dual / tri color bars
Steady On Mode: Accessible with PC App only and allows the user to program any light module to turn on steady at
100% duty cycle.
Stop / Tail / Turn Mode: Allows the user to program any Light Head Group(s) to operate in 2 levels of intensity for tail
and stop/turn functions.
Low Power Mode: Operates lighting at reduced intensity. Selectable between 20 and 90% duty cycle.
Scene Lighting Mode: Allows the user to program any Light Head Group(s) to turn on steady when this feature is
activated to provide additional scene lighting. The activation of this input also activates the Takedown function
Speed Sense Input: The breakout box has a speed sense input that is capable of sensing vehicle speed when connected
to the Vehicle Speed Sens e (VSS) trigger wire which is supplied in the police upfitter wire harness for some vehicles. This
feature is configured using the PC configuration software utility.
Auto Dimming: Operates lightbar at reduced intensity when ambient light is low.
Matrix Input: Matrix inputs are virtual inputs which can be triggered based on combinations of up to four physical wires
or siren input signals. This feature also allows the installer to invert the state of inputs, latch momentary inputs and adjust
trigger timing through on and off delay timer settings. This feature is configured using the PC configuration software
utility.

9 1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar

ELECTRICAL INSTALLATION
Power Cable:
1. Route lightbar power cables as close to vehicles power source (battery) as possible.
2. Install a maximum of 35Amp Fuse (customer supplied) to the end of the RED wire of the Lightbar Power Cable.
a. Remove the fuse before connecting any wires to the battery.
b. DO NOT USE CIRCUIT BREAKER OR FUSIBLE LINK.
3. Connect the other end of the Fuse to the POSITIVE (+) terminal of the battery.
a. Do NOT use any more than 2ft of wire between the battery terminal and the fuse and ensure the wire is protected and
secured from being cut into; this is non-fused wire.
4. Connect the BLACK wire to the factory chassis ground right next to the battery.

Control (Data) Cable:

1. Route Lightbar Control Cable to the location where all controlling equipment will be, i.e. switch box, center console
area.
2. Locate the Breakout Box in the same area to connect jumpers from the switching equipment to the breakout box.
3. Refer to breakout box hookup table on page 9.
NOTE: Breakout Box must be mounted inside vehicle where it will not get wet.

Initial Power up Test:

1. Connect the red and the black wire from lightbar to red and black wire of the 4-pin Breakout Box Harness as shown on
page 16
2. Connect Green wire from lightbar to green LIN 1 of the 4-pin Breakout Box Harness as shown on page 16.
3. Apply power to pink/white ignition wire on breakout box. See table 1 on page 16.
4. Observe the GREEN Data Link indicator LED on the Breakout Box; the Green LED will be ON showing power is
connected.
5. The Red indicator LED on the breakout box will be steady ON whenever any of the input wires are active or data is
received from a siren.

Low Power (Standby) Mode (reduced standby current)

If there is no input to the breakout box the lightbar will go into a “standby” mode. The standby mode is a low power
mode that is used to extend the life of your battery. The lightbar will awaken from the standby mode if any input is
activated on the breakout box.

IMPORTANT ! WARNING
WHEN PASSING CABLES THROUGH FIREWALL OR OTHER Route wires only in locations that are not subjected to
SHEETMETAL, INSERT GROMMET TO PROTECT THE CABLE! potential wear. Ma ke sure to avoid routing wires in the
deployment area of your air ba g. Refer to your vehicle’s
owner’s manual for airbag deployment zone.

! WARNING
ALL CUSTOMER SUPPLIED POWER WIRES CONNECTING TO THE POSITIVE (+) OR NEGATIVE (-) BA TTERY
TERMINAL OR LOCAL CHASIS GROUND (-) MUST BE SIZED TO SUPP LY AT LEAST 125% OF THE MAXIMUM
CURRENT AND PROPERLY FUSED AT THE POWER SOURCE WITH APPROPI ATELY RATED FUSE.

10 1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar

ELECTRICAL INSTALLATION (CONT.)

FLASH PATTERNS *fpm=Flashes per Minute

**fps=Flashes per Second

SAE Com- ECE California Title

# Name pliant Compliant 13 Compliant Color Sequence fpm fps
Timing Timing Timing
SC1 Random 1 Yes No No #1 Variable - -
SN2 Random 2 No No No #1 Variable - -
SC3 Quint Yes No No #1 Alternating 70 1.2
SC4 Quad 2 Yes No No #1 Variable - -
SC5 Q-Switch Yes No No #1 Variable - -
SC6 Double Yes No No #1 Alternating 115 1.9
SC7 Power Pulse Yes No No #1 Alternating 180 3
SC8 Road Runner Yes No Yes #1 Alternating 115 1.9
SC9 Slow Runner Yes No Yes #1 Alternating 70 1.2
SN10 Warp No No No #1 Alternating 350 5.8
SN11 Inter-Cycle No No No #1 Alternating - -
SN12 Warp 1-2-3 No No No #1 Alternating - -
SC13 E-Single Yes Yes No #1 Alternating 125 2.1
SC14 E-Double Yes Yes No #1 Alternating 125 2.1
SC15 E-Triple Yes Yes No #1 Alternating 125 2.1
SC16 E-Single Sim Yes Yes No #1 Simultaneous 125 2.1
SC17 E-Double Sim Yes Yes No #1 Simultaneous 125 2.1
SN18 Super Slow Runner No No No #1 Alternating 55 0.9
SC19 Quint Simultaneous Yes No No #1 Simultaneous 70 1.2
SC20 Road Runner Simultaneous Yes No No #1 Simultaneous 114 1.9
SC21 Quint Pass/Steady Driver Yes No No #1 - 70 1.2
SC22 Road Runner Pass/Steady Driver Yes No No #1 - 114 1.9
SC23 Quint 2 Yes No No #1 - 70 1.2
SN24 Warp 2 No No No #1 - 350 5.8
SN25 Inter-Cycle 2 No No No #1 - - -
SN26 Flicker Brake No No No #1 - - -
SN27 Flicker Cruise No No No #1 - - -
SN28 Steady No No No #1 - - -
SN29 Manifesto No No No #1 - - -
SN30 Power Evert No No No #1 - - -
SN31 Dazzle No No No #1 - - -
SN32 Quiver No No No #1 - - -
NOTE: Takedown light patterns are limited to pattern #1 – 25

11 1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar

ELECTRICAL INSTALLATION (CONT.)

FLASH PATTERNS CONT. *fpm=Flashes per Minute

**fps=Flashes per Second

SAE
ECE Compli- California Title 13
# Name Compliant Color Sequence fpm fps
ant Timing Compliant Timing
Timing
SN33 Power Sway No No No #1 - - -
SN34 Evert No No No #1 - - -
SN35 Alternating Rapid Flash No No No #1 - - -
SN36 Swift Impact No No No #1 - - -
SN37 Tango No No No #1 - - -
SN38 Tremble No No No #1 - - -
SN39 Shake No No No #1 - - -
SN40 Evolver No No No #1 Simultaneous - -
SN41 Corner Sweep No No No #1 - - -
SN42 Corner Sweep Slow No No No #1 - - -
SN43 Full/Sweep No No No #1 - - -
SN44 Full/Sweep Slow No No No #1 - - -
SN45 Center Sweep No No No #1 - - -
SN46 Center Sweep Slow No No No #1 - - -
SN47 Orbit No No No #1 - - -
SN48 Orbit Slow No No No #1 - - -
SN49 Double Orbit No No No #1 - - -
SN50 Slow Double Orbit No No No #1 - - -
SN51 Retrograde Orbit No No No #1 - - -
SN52 Slow Retrograde Orbit No No No #1 - - -
SN53 Progressive Alternate No No No #1 - - -
SN54 Recurrent No No No #1 Simultaneous - -
SN55 E-Scroll No Yes No #1 Alternating - -
SN56 ECE-Single - Aura No No No #1 Alternating - -
SN57 ECE-Single - Aura II No No No #1 Alternating - -
DC1 Random Dual #1 Yes No No #1/2 Variable - -
DN2 Random Dual #2 No No No #1/2 Variable - -
DC3 Quint Dual Yes No No #1/2 Alternating 70 1.2
DC4 Quad 2 Dual Yes No No #1/2 Variable - -
DC5 Q-Switch Dual Yes No No #1/2 Variable - -
DC6 Double Dual Yes No No #1/2 Alternating 115 1.9
DC7 Power Pulse Dual Yes No No #1/2 Alternating 180 3
DC8 Road Runner Dual Yes No Yes #1/2 Alternating 115 1.9
DC9 Slow Runner Dual Yes No Yes #1/2 Alternating 70 1.2
DN10 Warp Dual No No No #1/2 Alternating 350 5.8
DN11 Inter-Cycle Dual No No No #1/2 Alternating - -
DN12 Warp 1-2-3 Dual No No No #1/2 Alternating - -
DN13 Pattern #1 Dual No No No #1/2 Variable - -
DN14 Pattern #2 Dual No No No #1/2 Variable - -

12 1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar

ELECTRICAL INSTALLATION (CONT.)

FLASH PATTERNS CONT. *fpm=Flashes per Minute

**fps=Flashes per Second

ECE California Title

SAE Compli-
# Name Compliant 13 Compliant Color Sequence fpm fps
ant Timing
Timing Timing
DN15 Impact Dual No No No #1/2 Variable - -
DN16 Explosion Dual No No No #1/2 Variable - -
DC17 Quint Simultaneous Dual Yes No No #1/2 Simultaneous 70 1.2
DC18 Road Runner Sim. Dual Yes No No #1/2 Simultaneous 114 1.9
DC19 Quint 2 Dual Yes No No #1/2 - 70 1.2
DN20 Warp 2 Dual No No No #1/2 - 350 5.8
DN21 Inter-Cycle 2 Dual No No No #1/2 - - -
DN22 Super Slow Runner Dual No No No #1/2 - - -
DN23 Flicker Cruise Dual No No No #1/2 - - -
DN24 Manifesto Dual No No No #1/2 - - -
DN25 Power Evert Dual No No No #1/2 - - -
DN26 Dazzle Dual No No No #1/2 - - -
DN27 Quiver Dual No No No #1/2 - - -
DN28 Power Sway Dual No No No #1/2 - - -
DN29 Evert Dual No No No #1/2 - - -
DN30 Alternating Rapid Flash Dual No No No #1/2 - - -
DN31 Swift Impact Dual No No No #1/2 - - -
DN32 Tango Dual No No No #1/2 - - -
DN33 Tremble Dual No No No #1/2 - - -
DN34 Shake Dual No No No #1/2 - - -
DN35 Evolver Dual No No No #1/2 Simultaneous - -
DN36 Corner Sweep Dual No No No #1/2 - - -
DN37 Corner Sweep Slow Dual No No No #1/2 - - -
DN38 Full/Sweep Dual No No No #1/2 - - -
DN39 Full/Sweep Slow Dual No No No #1/2 - - -
DN40 Center Sweep Dual No No No #1/2 - - -
DN41 Center Sweep Slow Dual No No No #1/2 - - -
DN42 Orbit Dual No No No #1/2 - - -
DN43 Orbit Slow Dual No No No #1/2 - - -
DN44 Double Orbit Dual No No No #1/2 - - -
DN45 Slow Double Orbit Dual No No No #1/2 - - -
DN46 Retrograde Orbit Dual No No No #1/2 - - -
DN47 Slow Retrograde Orbit Dual No No No #1/2 - - -
DN48 Progressive Alternate Dual No No No #1/2 - - -
DN49 Recurrent Dual No No #1/2 Simultaneous - -
DN50 E-Scroll Dual No Yes No #1/2 Alternating - -
DN51 Road Runner Dual - Aura No No No #1/2 Alternating - -
DN52 Road Runner Dual - Aura II No No No #1/2 Alternating - -
DN53 Slow Runner Dual - Aura No No No #1/2 Alternating - -

13 1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar

ELECTRICAL INSTALLATION (CONT.)

FLASH PATTERNS CONT. *fpm=Flashes per Minute

**fps=Flashes per Second

SAE ECE
California Title 13
# Name Compliant Compliant Color Sequence fpm fps
Compliant Timing
Timing Timing
DN54 Slow Runner Dual - Aura II No No No #1/2 Alternating - -
DN55 Super Slow Runner Dual - Aura No No No #1/2 Alternating - -
DN56 Super Slow Runner Dual - Aura II No No No #1/2 Alternating - -
DN57 Corner Sweep Slow Dual - Aura No No No #1/2 - - -
DN58 Full Sweep Slow Dual - Aura No No No #1/2 - - -
DN59 Center Sweep Slow Dual - Aura No No No #1/2 - - -
DN60 Orbit Slow Dual - Aura No No No #1/2 - - -
DN61 Double Orbit Slow Dual - Aura No No No #1/2 - - -
DN62 Retrograde Orbit Slow Dual - Aura No No No #1/2 - - -
DN63 Flicker Cruise alternate Dual - Aura No No No #1/2 - - -
TN1 Pattern 1 Tri No No No #1/2/3 Alternating - -
TN2 Random Tri No No No #1/2/3 Alternating - -
TC3 Quint Tri Yes No No #1/2/3 Alternating 70 1.2
TC4 Quad 2 Tri Yes No No #1/2/3 Alternating - -
TN5 Pattern 2 Tri No No No #1/2/3 - - -
TC6 Double Tri Yes No No #1/2/3 Alternating 115 1.9
TC7 Power Pulse Tri Yes No No #1/2/3 Alternating 180 3
TC8 Road Runner Tri Yes No Yes #1/2/3 Alternating 115 1.9
TC9 Slow Runner Tri Yes No Yes #1/2/3 Alternating 70 1.2
TN10 Warp Tri No No No #1/2/3 Alternating 350 5.8
TN11 Inter-Cycle Tri No No No #1/2/3 Alternating - -
TN12 Warp 1-2-3 Tri No No No #1/2/3 Alternating - -
TN13 Super Slow Runner Tri No No No #1/2/3 Alternating 55 0.9
TC14 Quint Simultaneous Tri Yes No No #1/2/3 Simultaneous 70 1.2
TC15 Road Runner Sim. Tri Yes No No #1/2/3 Simultaneous 114 1.9
TC16 Quint 2 Tri Yes No No #1/2/3 Alternating 70 1.2
TN17 Warp 2 Tri No No No #1/2/3 Alternating 350 5.8
TN18 Inter-Cycle 2 Tri No No No #1/2/3 Alternating - -
TN19 Pattern 3 Tri No No No #1/2/3 - - -
TN20 Flicker Cruise Tri No No No #1/2/3 - - -
TN21 Manifesto Tri No No No #1/2/3 - - -
TN22 Power Evert Tri No No No #1/2/3 - - -
TN23 Dazzle Tri No No No #1/2/3 - - -
TN24 Quiver Tri No No No #1/2/3 - - -
TN25 Power Sway Tri No No No #1/2/3 - - -
TN26 Evert Tri No No No #1/2/3 - - -
TN27 Alternating Rapid Flash Tri No No No #1/2/3 - - -
TN28 Swift Impact Tri No No No #1/2/3 - - -
TN29 Tango Tri No No No #1/2/3 - - -

14 1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar

ELECTRICAL INSTALLATION (CONT.)

FLASH PATTERNS CONT. *fpm=Flashes per Minute

**fps=Flashes per Second

SAE ECE
California Title 13
# Name Compliant Compliant Color Sequence fpm fps
Compliant Timing
Timing Timing
TN30 Tremble Tri No No No #1/2/3 - - -
TN31 Shake Tri No No No #1/2/3 - - -
TN32 Evolver Tri No No No #1/2/3 Simultaneous - -
TN33 Corner Sweep Tri No No No #1/2/3 - - -
TN34 Corner Sweep Slow Tri No No No #1/2/3 - - -
TN35 Full/Sweep Tri No No No #1/2/3 - - -
TN36 Full/Sweep Slow Tri No No No #1/2/3 - - -
TN37 Center Sweep Tri No No No #1/2/3 - - -
TN38 Center Sweep Slow Tri No No No #1/2/3 - - -
TN39 Orbit Tri No No No #1/2/3 - - -
TN40 Orbit Slow Tri No No No #1/2/3 - - -
TN41 Double Orbit Tri No No No #1/2/3 - - -
TN42 Double Orbit Slow Tri No No No #1/2/3 - - -
TN43 Retrograde Orbit Tri No No No #1/2/3 - - -
TN44 Retrograde Orbit Slow Tri No No No #1/2/3 - - -
TN45 Progressive Alternate Tri No No No #1/2/3 - - -
TN46 Recurrent Tri No No No #1/2/3 Simultaneous - -
TN47 E-Scroll Tri No Yes No #1/2/3 Alternating - -
TN48 Road Runner Tri - Aura No No No #1/2/3 Alternating - -
TN49 Road Runner Tri - Aura II No No No #1/2/3 Alternating - -
TN50 Slow Runner Tri - Aura No No No #1/2/3 Alternating - -
TN51 Slow Runner Tri - Aura II No No No #1/2/3 Alternating - -
TN52 Super Slow Runner Tri - Aura No No No #1/2/3 Alternating - -
TN53 Super Slow Runner Tri - Aura II No No No #1/2/3 Alternating - -
TN54 Corner Sweep Slow Tri - Aura No No No #1/2/3 - - -
TN55 Full Sweep Slow Tri - Aura No No No #1/2/3 - - -
TN56 Center Sweep Slow Tri - Aura No No No #1/2/3 - - -
TN57 Orbit Slow Tri - Aura No No No #1/2/3 - - -
TN58 Double Orbit Slow Tri - Aura No No No #1/2/3 - - -
TN59 Retrograde Orbit Slow Tri - Aura No No No #1/2/3 - - -

15 1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar

ELECTRICAL INSTALLATION (CONT.)

ARROW PATTERNS

SAE ECE California Title

# Name Compliant Compliant 13 Compliant Color Sequence fpm fps
Timing Timing Timing
1 Single Fast No No No #1 - - -
2 Single Slow No No No #1 - - -
3 Chaser Fast No No No #1 - - -
4 Chaser Slow No No No #1 - - -
5 Fill Fast No No No #1 - - -
6 Fill Slow No No No #1 - - -
7 Grow/Shrink No No No #1 - - -
8 Warning w/Arrow No No No #1 - - -
9 Warning w/Arrow Fill No No No #1 - - -
10 Arrow Random 1 No No No #1 - - -
11 Arrow Random 2 No No No #1 - - -
12 Grow/Shrink 2 No No No #1 - - -
13 Single Slow - Aura III No No No #1 - - -
14 Fill Slow - Aura III No No No #1 - - -

16 1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar

ELECTRICAL INSTALLATION (CONT.)

* Switch #1 and #2 on the Breakout Box can be used when 35 Amp Fuse
configuring the bar with the bluePrint Control system Red

Black
Green
-
Switch #1*
Switch #2*
Universal B.O.B. - Connectivity Side Red LED + 3 Amp
Fuse
Green LED
(Ground)
(Ground)

Red
Green

Black Green/White (Not used)

(Ground)
USB Programming Connector
Universal B.O.B. - Activation Side

3 Amp Fuse
Pink/White +10-32 VDC
Switched Ignition Source

Universal Breakout Box

Setting I.D.
*Only used with bluePRINT
applications with more than
1 Universal Brealout Box.
PIN#24 - Light Green/ White
PIN#22 - Orange/ White
PIN#21 - Yellow/ White

1 - Up/Off 1 - Down/On
ID 1 ID 3
PIN#19 - Red/ White

2 - Up/Off 2 - Up/Off
PIN#23 - Red Black

PIN#16 - Orange
PIN#15 - Yellow
PIN#20 - Brown

PIN#14 - Green
PIN#13 - Blue
PIN#18 - Pink
PIN#17 - Red

1 - Up/Off 1 - Down/On
ID 2 2 - Down/On ID 4 2 - Down/On

Functional Inputs
Functional Inputs connect to your control
head or switching unit. Applying +10-32Vdc
to any functional Input will activate it’s
function (default-active high).
Light Green - PIN#5

Green White - PIN#2

Purple/ White - PIN#11

Brown/ White - PIN#6

Gray/ White - PIN#10

Blue/ White - PIN#1

Black/ White - PIN#9
Pink/ White - PIN#12

Purple - PIN#7
White - PIN#8

Gray - PIN#3
Black - PIN#4

USB Type Mini B Connector

For Software Programming
.

17 1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar

WIRE FUNCTION DEFAULTS

Table 1
Color CERT chosen
Wire (→: If the color is not SAE/None ECE
Wire Color Wire Func�on Mods affected Flash
Pin # populated, it would be the
Pa�ern
next color listed)
1 BLU/WHT Cruise 1 Inboard 1, Corners & Alleys (Front and Rear) Color 1, not White - - -
2 GRN/WHT Warning En�re Bar (Rear) Color 1 Mode 2 Slow Runner ECE Single
3 GRY STT - Rear Turn - Le� Inboard 2 (pair) Amber→Red→nothing - - -
4 BLK STT - Rear Turn - Right Inboard 2 (pair) Amber→Red→nothing - - -
5 LTGRN STT - Tail Inboard 2 (pair) Red→nothing - - -
6 BRN/WHT Disable Le� Side Endcap - - - -
7 PUR Disable Right Side Endcap - - - -
8 WHT Unassigned - - - - -
9 BLK/WHT Low Power 1 all - - - -
10 GRY/WHT Le� Arrow Inboards (Rear) Amber→Color 1 - - -
11 PUR/WHT Right Arrow Inboards (Rear) Amber→Color 1 - - -
12 PNK/WHT IGNITION - - - - -
13 BLU Warning En�re Bar (Front and Rear) Color 1 Mode 1 Flicker Cruise ECE Single
14 GRN Warning En�re Bar (Front) Color 1 Mode 2 Slow Runner ECE Single
15 YEL Warning En�re Bar (Front and Rear) Color 1 Mode 3 Quint ECE Single
16 ORG Warning En�re Bar (Front and Rear) Color 1 Mode 4 Intercycle ECE Single
17 RED Warning En�re Bar (Front and Rear) Color 1 Mode 5 Warp ECE Single
18 PNK Warning with Cruise 1 behind En�re Bar (Front and Rear) Color 1 Mode 6 Super Slow Runner ECE Single
19 RED/WHT Flashing Takedown White→nothing - - -
20 BRN Scene Le� Alley and Le� Alley Scene White→nothing - - -
21 YEL/WHT Scene Right Alley and Right Alley Scene White→nothing - - -
22 ORG/WHT Takedown Selected at Bar Crea�on White - - -
23 RED/BLK Scene 1 Selected at Bar Crea�on White - - -
24 LTGRN/WHT VSS Input for Speed 1 and 2 - - - - -
BREAKOUT BOX INSTRUCTIONS: CAN BREAKOUT BOX INSTRUCTIONS:
(LIN COMMUNICATION) (CAN COMMUNICATION)
a) Securely snap in the 4-pin, 5-pin and 24-pin connectors
a) Securely snap in the 4-pin and 24-pin connectors b) Refer to Table 1 for the input wire default functions and to
b) Install a 53Amp Fuse (customer supplied) 4to the end of the Red 3
Table 3 for the CAN wire functions
2 1
wire of the 4-pin connector harness. c) Install a 3Amp Fuse (customer supplied) to the end of the
c) Hook up power, ground, and LIN to the corresponding wire Red wire of the 4-pin connector harness. (Table REVISION LOG
2)
E on the 4-pin connector harness. (Table 2)
d) Hook up power, ground, and REV LIN to the corresponding
DESCRIPTION wire ECN D
INITIALS
d) Refer to Table 1 for the input wire’s default function on the 4-pin connector harness. (Table 2)
1 01/
e) Follow the label for the wire color to connect to a +10-32Vdc e) Follow the label for the wire color to connect to a 10-32 Vdc
source, which turns on that given light or lights source, which turns on that given light or lights
f) Make sure your wire5 connections are secured and4isolated f) Make sure3 your wire connections are secured
2 and isolated 1
from any other wire from any other wire
4-PIN CONNECTOR HARNESS g) If extending the 5-pin connector harness, a shielding wire
REVISION LOG

E running the length of the entire REV

harness may be necessary
DESCRIPTION INITIALS ECN
INSULATION: HDPE
4 CONNECTOR PRESENT WITH
A CANRELEASE
BOB FOR GRP 5710
D PRODUCTION
50 mm 5mm
Table 2 CHANGED OVERALL
B LENGTH FROM 300mm GRP xxxx
Wire Pin Color Function TO 400mm
1 Black Ground
2 Green/White LIN 2 - not 8mm 2mm HALF STRIP
used with this lightbar
3 30mm 1
3 Green LIN 1 - mpower Lightbar Operation 3 5
D 400 mm 5mm Table 3
4 Red Power 2 Wire Pin Color Function
3 Green CAN Low
C
5 Yellow CAN High
NOTES: CAN CONNECTOR
MECHANICAL CHARACTERISTICS(@ 1MHz)
CONDUCTORS 20-22 AWG STRANDED BARE COPPER
5 CHARACTERISTIC
TEMPURATURE NUMBERS
RANGE -30 TO 65C
INSULATION: HDPE
LAST USED
CONSTRUCTION: DELETED
SHIELDED TWISTED PAIR K
C INDUSTRY APPROVAL: SAE J1128
TO CHANGE WIRE FUNCTIONS FOR CUSTOM APPLICATIONS PLEASE SCAN QR CODE FOR LINK

18
ELECTRICAL CHARACTERISTICS(@1MHz)
FOR SOUNDOFF CENTRAL
HOUSING LIGHTBAR SOFTWARE GUIDES.
CONNECTOR: CHARACTERISTIC INDEPENDANCE 108-132 Ohms
NOTES: CAPACITENCE CONNNECTOR PROPRIETARY
TO CONDUCTOR <75
JST P/N: PAP-05V-S CAPACITANCE CONDUCTOR TO THESHIELD:
AND CONFID
<110pF/
INFORMATION m
CONTAI
1. CAD DATA IS MASTER
B 1.800.338.7337 / www.soundoffsignal.com 2. VOLUME = $PRPSHEET:{VOLUME MM} mm³ 2. TESTING: mPower® Exterior Light BarTHIS DRAWING IS THE SOLE
English
PROPERTY OF SOUNDOFF S
- VERIFY END TO END CONTINUITY AND NO SHORT
3. BREAK ALL SHARP EDGES, NO BURRS ALLOWED CIRCUITS BETWEEN00KPJL
PINS 0924
® ANYREV
REPRODUCTION
F IN PA
4. GATE & EJECTOR LOCATIONS TO BE APPROVED AS A WHOLE WITHOUT THE
-TOLERANCES
PULL STRENGTH ON CONNECTOR TO BE MIN 30N(6
WRITTEN PERMISSION OF
BY SOUNDOFF SIGNAL PRIOR TO TOOL BUILD -INDUSTRY
EXCEPT AS NOTEDAPPROVAL: SAE J1128
SOUNDOFF SIGNAL IS PROH
5. NO SUBSTITUTION OF MATERIAL ALLOWED WITHOUT - .X
EACH SHIPMENTTHIRD
± .020 OR LOT OF HARNESSES SHIPPED TO
ANGLE
SOUNDOFF SIGNAL APPROVAL .XX ± .012 CAD DIMENSIONS
HAVE A CERTIFICATE OF COMPLIANCE ARE BAS
INCLUDED
mpower® Exterior Light Bar

CONNECTION OF LIGHTBAR BREAKOUT BOX TO SOUNDOFF SIGNAL SIREN:

Note: Requires PC configuration app to map siren control switches to lightbar functions. Plug 1 end of RJ-45 cable to available jack on siren amplifier.

ETSA481CSR or ETSA482CSR

CN6
Breakout Box
CN2

Lightbar

ETSA5100/5200

UNIVERSAL BREAKOUT BOX

- BACK

Lightbar

SoundOff Central® Software Universal Breakout Box ID Settings

When using more than one lightbar universal breakout box (UBOB) with SoundOff Central Software, set the ID number for
each UBOB using the dip switches and then configure the light bars accordingly in the Software.

1. Select Lightbars Tab on

the main SETUP Page.

2. Under Lightbars tab, select the EXTERNAL tab 3. Hover cursor over the to open up
to see UBOB list. The number after the UBOB is Universal Breakout Box ID Information.
the ID needed.

19 1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar

SIREN FUNCTIONS

"Color CERT chosen

(if the color is not SAE/NONE ECE
# Button Function Mods affected populated, it would Flash
be the next color Pattern
listed)"
S1 Pushbutton 1 Left Arrow Inboards Amber→Color 1 - - -
S2 Pushbutton 2 Scene Left Alley and Left Alley Scene White→nothing - - -
S3 Pushbutton 3 Scene Right Alley and Right Alley Scene White→nothing - - -
S4 Pushbutton 4 Takedown Selected at Bar Creation White - - -
S5 Pushbutton 5 Cruise 1 Inboard 1, Corners & Alleys (Front and Rear) Color 1 - - -
S6 Pushbutton 6 Low Power 1 Entire Bar - - - -
S7 Pushbutton 7 Scene 1 Selected at Bar Creation White - - -
S8 Pushbutton 8 - No - - -
S9 SingleButtonArrow Right Arrow Inboards Amber→Color 1 - - -
S10 Slide Switch 1 Warning Entire bar (Rear) Color 1 Mode 2 Slow Runner ECE Single
S11 Slide Switch 2 Warning Entire Bar (Front and Rear) Color 1 Mode 3 Quint ECE Single
S12 Slide Switch 3 Warning Entire Bar (Front and Rear) Color 1 Mode 4 Intercycle ECE Single

PHOTO SENSOR
The photo sensor continuously monitors ambient light conditions and will control functions configured for operation with
the photo sensor input. By default, the photo sensor will set all light modules into low power mode when dark ambient
light levels below 50 lux are detected for more than 5 seconds. When ambient light levels exceed 300 lux for 5 seconds,
the low power mode will clear/turn off and the lightbar will revert back to full intensity.

The photo sensor is subject to ambient light conditions of the specific environment for the vehicle and needs to be thor-
oughly tested by the installer to ensure proper light levels and delay are selected to provide the most effective operation
in different lighting conditions.

The photo sensor detects ambient light levels, so parking the vehicle under a bright street light during night-time use may
(CLEAR) turn off the photo sensor input. Likewise, driving though a dark tunnel during daytime use may (SET) the photo
sensor input. Ensure the operator of the vehicle is aware of such possible conditions and provide additional controls to the
breakout box to allow the operator the ability to manually over-ride the functions when required.

The photo sensor is located in the middle of the AutoDim / Mod ID module.

Changing the ambient light SET/CLEAR levels may be modified by updating the setting in the 'Photo Sensor' tab in the PC
Application.

The photo sensor controls may be updated by using the PC App. Refer to the PC App instructions for more detail.

20 1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar

LED MODULE REPLACEMENT

LED Module Replacement:
1. Remove top cover by removing screws.
2. Disconnect the harness of the module in question from the driver board.
3. Remove the entire light module being replaced.
4. Replacement modules should be connected to the mpower Connector port
on the AutoDim / Mod ID module.
5. Once the module is connected, the LED’s under the 10’s and 1’s labels on
the AutoDim / Mod ID module will flash Green to indicate to the module’s
ID number.
nFuse nForce
EXAMPLE: An ID of 20 will flash only the 10’s LED twice. Similarly an
ID of 2 will flash only the 1’s LED twice. An ID of 15 would flash the AUTODIM / MOD ID MODULE
10’s LED once then the 1’s LED 5 times.
6. To configure a new ID, quick press the 10’s button to add 10 to the current ID and/or press the 1’s button to add 1 to the current ID.
Pressing and holding the 10’s or 1’s button until the corresponding red LED goes off will subtract 10 or 1 respectively. Pressing and
holding both the 10’s and 1’s buttons at the same time and releasing once the red LED’s turn off will change the ID to 1.
7. Once the 10’s or 1’s buttons have been pressed the LED’s on the AutoDim / Mod ID module will change from green to red and flash
the potential new ID. If the ID flashes correctly press the SET button and it will configure the module to that ID. The LED’s on the
AutoDim / Mod ID module will now flash the module’s new ID in green. If the new module ID flashes in green correctly then the
module is ready to be connected to the bar.
EXAMPLE: If your module started out with ID 15 and the desired ID was 30 you would press the 10’s button once and the
1’s button 5 times(15 + 15 = 30.) Verify the 10’s LED flashes red 3 times(indicating ID 30) then press the SET button. After
the SET button is pressed the 10’s LED should flash green 3 times.
NOTE: The highest available ID is 60. Going past 60 will start back at 1 and going backwards from 1 will go to 60.
8. Replace the top cover and use the replacement screws that are included with the replacement module.

MODULE LOCATION ID'S

48" LIGHTBAR
FCNR FINB1 FINB2 FINB3 FINB3 FINB2 FINB1 FCNR
ID3 ID4 ID5 ID10 ID11 ID12
ID2 ID13

ID1 ID14
ALS: ID60
ALLEY ALLEY
ALS ID:60
ID30 ID15

ID29 ID16

ID28 ID17
ID27 ID26 ID25 ID20 ID19 ID18
RCNR RINB1 RINB2 RINB3 RINB3 RINB2 RINB1 RCNR

55" LIGHTBAR
FCNR FINB1 FINB2 FINB3 FINB4 FINB3 FINB2 FINB1 FCNR
ID3 ID4 ID5 ID6 ID10 ID11 ID12
ID2 ID13

ID1 ID14
ALS: ID60
ALLEY ALLEY
ID30 ALS ID:60 ID15

ID29 ID16
ID28 ID17
ID27 ID26 ID25 ID24 ID20 ID19 ID18
RCNR RINB1 RINB2 RINB3 RINB4 RINB3 RINB2 RINB1 RCNR

21 1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar
REPLACEMENT PARTS & ACCESSORIES

6 5
1 2

ITEM # PART# STEALTH PART # DESCRIPTION

2 PMPLBCSS204(x)C PMPLBCSS204(x)S 4 LED SINGLE COLOR 3" CORNER MODULE (SAE)
2 PMPLBCSS208(x)C PMPLBCSS208(x)S 8 LED SINGLE COLOR 3" CORNER MODULE (SAE)
2 PMPLBCES208(x)C 8 LED SINGLE COLOR 3” CORNER MODULE (ECE)
2 PMPLBCSD208(x)C PMPLBCSD208(x)S 8 LED DUAL COLOR 3" CORNER MODULE (SAE)
2 PMPLBCST212(xxx)C PMPLBCST212(xxx)S 12 LED TRI COLOR 3" CORNER MODULE (SAE)
1 PMPLBLLS206(x)C PMPLBLLS206(x)S 6 LED SINGLE COLOR 6" INBOARD MODULE
1 PMPLBLLS208(x)C PMPLBLLS208(x)S 8 LED SINGLE COLOR 6" INBOARD MODULE
1 PMPLBLLD212(x)C PMPLBLLD212(x)S 12 LED DUAL COLOR 6" INBOARD MODULE
1 PMPLBLLT218(xxx)C PMPLBLLT218(xxx)S 18 LED TRI COLOR 6" INBOARD MODULE
3 PMPLBDRV3 MPOWER LB DISTRIBUTION BOARD
5 PMPLBDAD1 MPOWER LB ALS/MOD BOARD
PMPLBHNPW2 POWER HARNESS (15FT)
PMPLBHNPW3 POWER HARNESS (25FT)
PUVBBJ00 UNIVERSAL BREAKOUT BOX - STANDARD LIN COMMUNICATION
PUVBBJC1 UNIVERSAL BREAKOUT BOB - CAN COMMUNICATION
PUVBBHNCN1 CAN BREAKOUT BOX 5-PIN HARNESS
PUVBBHNPW1 BREAKOUT BOX 4-PIN HARNESS
PEPL9BBHN(x) BREAKOUT BOX 24-PIN HARNESS
4 PMPLBTSL48 PMPLBTBL48 MPOWER LB 48" TOP COVER 6"
4 PMPLBTSL55 PMPLBTBL55 MPOWER LB 55" TOP COVER 6"
PMPLBK00 STANDARD FIXED HEIGHT MOUNT w/THICK & THIN PADS
PMPLBK01 STANDARD FIXED HEIGHT MOUNT w/THICK PADS
PMPLBK02 STANDARD FIXED HEIGHT MOUNT w/THIN PADS
PMPLBK03 CLASSIC FIXED HEIGHT MOUNT
PMPLBK04 EXTRA LOW FIXED HEIGHT MOUNT
PMPLBK05 XtraFit UNIVERSAL MOUNT
PMPLBK06 HEADACHE RACK MOUNT
6 PMPLBK09 SLIDING FIXED MOUNT
PMPLBDFL2S PMPLBDFL2B WIND NOISE DEFLECTOR KIT

22 1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F
mpower® Exterior Light Bar
MPOWER LIGHT BAR TROUBLESHOOTING
Normal Operation
Under Normal operation with ignition input powered, the breakout box will have the Green LED ON and the Red LED light
will be ON whenever an input is active and both switches are in the UP (off) position.
GENERAL TROUBLESHOOTING
Before further troubleshooting steps, • Check power source to the lightbar and breakout box (10AWG red and
start here: 22AWG red wires).
• Check the ground source to the lightbar and breakout box (10AWG black and
22AWG black wires).
• Check ignition source to the lightbar and breakout box (pink/white wire).
• Check any splice and butt connections for proper crimp integrity.
• Check connectors for positive engagement.
NO OPERATION
The green LED is not illuminated • Check Power (Pin #4) and Ground (Pin #1) on the 4-pin connector.
• If not connected to a 400 Series Siren or bluePRINT Controller, check Ignition
(pin #12) on the 24-pin connector.
The red LED is not illuminated while • Verify there is proper voltage on the input wire. Many inputs are positive or
inputs are active negative selectable (through SoundOff Central Lightbar).
• Check lightbar program configuration using SoundOff Central Lightbar. Verify
any active inputs are mapped to activate lightbar functions.
• Verify the DIP switches on the BOB are both in the up (off) position.
Green and red LEDs are illuminated • Verify the lightbar data wires on the 4-pin connector (pin #3) is correctly
properly connected to the light bar data wire.
• Verify the data wire circuit (from the breakout box into the lightbar) is not
damaged or shorted to power or ground.
NO LIGHT OPERATION IN ONE
LIGHTBAR QUADRANT
Breakout box LED’s operating correctly Remove top cover and follow the non-working modules wires to fuse location.
If fuse is blown, check for shorts in cabling and LED module. Replace any dam-
aged cables or modules and replace fuse. If fuse blows again, replace defective
power distribution assembly.
No Steady Red LED on breakout box Check 24-pin connector at breakout box (ensure it is snapped in correctly),
check appropriate input to breakout box for output lights which should be on.
NO TAKEDOWNS LIGHTS
Breakout box LED’s operating correctly; Verify configuration and make sure light modules are configured for takedown
function.
No steady Red LED on breakout box; Check 24-pin connector at breakout box (insure it is snapped in correctly),
check appropriate input to breakout box for output lights which should be on.
NO OR INCORRECT WARNING LIGHTS
• Verify the configuration for proper lightbar operation.
• Verify the lightbar data wires on the 4-pin connector (pin #3) is correctly
connected to the Lightbar data wire.
• Verify light module ID/positions.
INCORRECT OR NO ARROW OPERATION
Breakout box LED's operating correctly • Verify configuration and make sure light modules are configured for arrow
function.

No steady Red LED on breakout box • Check 24-pin connector at breakout box (ensure it is snapped into position
correctly), check appropriate input to breakout box for output lights which
should be on.

FOR MORE HELP WITH SOFTWARE PROGRAMMING, MODULE

23
ID SETTING AND REPLACEMENT PLEASE SCAN QR CODE FOR
SOUNDOFF CENTRAL LIGHTBAR GUIDES.
1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English
00KPJL 0924 REV F
mpower® Exterior Light Bar

WARRANTY & RETURN GOODS PROCEDURE

CLEANING & CARE OF YOUR LIGHTBAR: WARRANTY RETURN PROCESS:
Keeping the lenses clean and scratch free will optimize the Please scan QR code or visit
performance of the lightbar. The exterior of the lightbar https://soundoffsignal.com/support-page/returns/.
including lenses should be cleaned with mild soapy water and
a soft cotton cloth to remove dirt, grime and insects. Never Alternatively contact your SoundOff Signal Sales Representative,
use window cleaners or harsh chemicals on the lenses; this Customer Services staff or our Technical Department (800.338.7337)
may cause failure of the lenses or reduce clarity resulting in the for a RMA #, Return Merchandise Authorization Number.
reduction of light output.
The following information is required for issuance of the RMA #:
MOUNTING INTEGRITY:
A review of bolt/hardware/mounting bracket integrity should be • Reason for returning the product*
performed at the beginning and end of each shift. • Address where replacement product is to be shipped*
• Telephone number where you may be reached*
• SoundOff Signal invoice number on which product was
purchased**
• SoundOff Signal part number and serial number**
WARNING MESSAGES - PLEASE READ: • E-mail address where RMA # should be e-mailed**
• Fax number where RMA # should be faxed**

WARNING - DRILLING ANY HOLES INTO THE LIGHTBAR IS * RMA # will not be given without this information.
NOT RECOMMENDED! THE RISK OF DAMAGING INTERNAL ** If available, please provide this information.
COMPONENTS AND THE RESULTING FAILURE OF THE LIGHTBAR
WILL VOID ANY WARRANTY OF THIS PRODUCT. SoundOff Signal will NOT accept returns without an RMA #. Each
RMA # is good for only one (1) return and will expire (30) days after
the date it was issued. Products must be shipped back to SoundOff
WARNING - CARE MUST BE TAKEN WHEN DRILLING THROUGH Signal and the RMA # clearly marked on the outside of the package
THE ROOF OF THE VEHICLE NOT TO DRILL INTO ANY EXISTING near the shipping label. Please use the following address on your
WIRING AND NOT TO DRILL THROUGH THE HEADLINER OR shipping label:
SUPPORT MEMBERS OF THE VEHICLE. CHECK BOTH SIDES
OF THE MOUNTING SERVICE PRIOR TO DRILLING. DE-BURR SoundOff Signal
ANY HOLES AND REMOVE ANY METAL SHARDS OR REMNANTS. ATTN: RMA # / Technical Services
INSTALL GROMMETS INTO ALL WIRE PASSAGE HOLES. 3900 Central Parkway
Hudsonville, MI 49426
WARNING - ROUTE WIRES ONLY IN LOCATIONS THAT ARE WARRANTY EXCLUSIONS:
NOT SUBJECTED TO POTENTIAL WEAR. MAKE SURE TO AVOID Shipping & Handling, labor and service fees are non-refundable.
ROUTING WIRES IN THE DEPLOYMENT AREA OF YOUR AIR BAG. SoundOff Signal is not liable for any damage due to installation or
REFER TO YOUR VEHICLE OWNER’S MANUAL FOR AIR BAG personal injury as a result of using SoundOff Signal product.
DEPLOYMENT ZONES.
WARRANTY FORFEITURE:
WARNING - ALL CUSTOMER SUPPLIED POWER WIRES Warranty will not be granted if the Warranty Return Policy &
CONNECTING TO THE POSITIVE (+) OR NEGATIVE (-) BATTERY Procedure rules are not strictly followed. Physical damage resulting
TERMINAL OR LOCAL CHASSIS GROUND (-) MUST BE SIZED from customer abuse will void warranty. Warranty will also be
voided if any SoundOff Signal and/or manufacturer serial tags,
TO SUPPLY AT LEAST 125% OF THE MAXIMUM CURRENT AND product stickers, seals, or the like, are removed, altered or tampered
PROPERLY FUSED AT THE POWER SOURCE WITH APPROPRIATELY with. Returned product that is damaged by shipping via the RMA #
RATED FUSE. procedure is not the responsibility of SoundOff Signal.

IMPORTANT: When passing cables through fire wall or other Document effective date on cover and below supersedes previously
sheet metal, insert grommet to protect the cable! dated policies and statements.

There are no other warranties, expressed or implied, including, but

not limited to, any implied merchantability or fitness for a particular
use. SoundOff Signal reserves the right to modify this warranty
statement at any time; or to discontinue, modify, or upgrade any
products of its manufacture with design improvements without
prior notice.

24 1.800.338.7337 / www.soundoffsignal.com mPower® Exterior Light Bar English

00KPJL 0924 REV F