BOOM TRUCK

TM-20110
MAXIMUM LIFTING CAPACITY : 18TON

Courtesy of Crane.Market
TM-20110 (18 ton) crane specifications

MAXIMUM LIFTING CAPACITY

18,000 kg @ 1.5m (6-part lines)
BOOM
5-sectioned, fully powered synchronized telescoing boom of pentagonal box construction
Retracted length 8.3 m
Extended length 33.5 m
Extended speed 25.2 m / 73s @ 2,430rpm pump or 89s @ 2,000rpm pump
Elevation Elevated by double-acting hydraulic cylinder
Elevation speed -5˚ to 80˚ / 23s @ 2,430rpm pump or 28s @ 2,000rpm pump
NOTE: Extended speed and elevation speed are calculated under the condition that the flow is 95 L/min
Boom point 2 sheaves
WINCH
Hydraulic motor driven, Planetary gear speed reduction, provided with automatic break
Single line pull 3,265 kg
4,400 kg (Winch capacity of permissible line pull at 1st layer)
Single line speed 85 m/min (@ 3rd layer) @ 2,430rpm pump or 70m/min @ 2,000rpm pump
NOTE: Single line speed is calculated under the condition that the flow is 216 L/min
Wire rope
diameter x length 14 mm x 96 m
breaking strength 134 kN
SWING
Hydraulic motor driven, Planetary gear speed reduction
Continuous 360˚ full circle swing (Standard)
Swing speed 360˚ / 37s @ 2,430rpm pump or 45s @ 2,000rpm pump
Non-Continuous 375˚ rotation on ball bearing slew ring (Option)
Swing speed 375˚ / 38s @ 2,430rpm pump or 47s @ 2,000rpm pump
OUTRIGGERS
<CAB BACK MOUNTED>
Outriggers (Out & Down type)
Hydraulically extended sliders and hydraulically extended jacks, integral with crane frame
Extend width Min. 2,180mm
Mid. 4,000mm
Max.5,700mm
Rear stabilizers (Out & Down type)
Hydraulically extended sliders and hydraulically extended jacks, integral with chassis frame
Extend width Min. 2,250mm
Max.3,500mm
Single front stabilizer
Hydraulic extended jack in front of bumper for 360˚ lifting operations

<REAR MOUNTED>
Rear outriggers (Out & Down type)
Hydraulically extended sliders and hydraulically extended jacks, integral with crane frame
Extend width Min. 2,180mm
Mid. 4,000mm
Max.5,700mm
Front outriggers (Out & Down type)
Hydraulically extended sliders and hydraulically extended jacks, integral with chassis frame
Extend width Min. 2,180mm
Mid. 4,000mm
Max.5,700mm

Courtesy of Crane.Market
HYDRAULIC
Hydraulic motor For winch and swing
Control valves Multiple control valves with integral safety valve
Hydraulic pump 3-section gear pump
Winch system : (20.6Mpa)
121L/min@ 2,430rpm pump
99.6L/min@ 2,000rpm pump
Boom and outriggers system : (21.1 MPa)
95 L/min@ 2,430rpm pump
78.2L/min@ 2,000rpm pump
Swing system : (12.1 MPa)
25 L/min@ 2,430rpm pump
20.6L/min@ 2,000rpm pump
Reserve tank 295 L capacity
*PTO/Mounting note included
ELECTRICAL SYSTEM
Power supply DC12V with a converter (Step down converter from 24V)
SAFETY DEVICES
Pendant type over-winding cut out
Hook safety latch
Level gauge
Hydraulic safety valves, check valves and holding valves
Over load shutoff with load indicator (TADANO’s exlusive “AMA” system)
Load / Boom angle indication
Audible warning
External warning lamps
BOOM REST
Removable
TORSION BOX
<CAB BACK MOUNTED>
The weight of 22ft (6.7m) standard torsion box is approx. 1,800kg.

<REAR MOUNTED>
The weight of 14ft (3.6m) torsion box is approx. 1,400kg.
CRANE WEIGHT
Approx. 6,900 kg (bare), approx. 8,400kg (include all items; crane, tank, oil, rear stabilizer, boom rest, etc.)
OPTION
Hook block
Swivel hook with safety latch
1) 3,200kg capacity ( for single line use, 60kg)
2) 6,000kg capacity ( for two part lines use, 100kg)
3) 12,000kg capacity ( for four part lines line use, 160kg)
4) 18,000kg capacity ( for six part lines use, 220.5kg)
*Note
A crane does not come with a hook block as a standard item
and shall be ordered out from the above.

Courtesy of Crane.Market
TM-20110 (18 ton) crane capacity

WORKING RANGE
(m)
NOTE:
1) Rated lifting capacities on this chart show maximum allowable loads with outriggers
80˚ properly extended on a firm surface and the crane leveled and mounted on a factory
33.5
70˚ recommended truck. The rated lifting capacities in shaded areas are based on crane
35
strength and others, on its stability.
60˚ 2) The weight of handling devices such as hook block, slings, etc., must be considered part of
28.6
the load and must be deducted form the rated lifting capacities.
30 3) Weights of any accessories attached to the boom or loadline must be deducted from the
50˚
rated lifting capacities.
23.8 4) The operator must reduce loads to allow for such factors as wind, ground conditions, operating
40˚
speed and the effects of freely suspended loads such as boom deflection.

Lifting height (m)

25
5) For full capacity 360°around the truck, the chassis requires the front stabilizer (ex rear
18.9 mounted) and additional counterweight in the underside of the bed.
6) For boom length or radius not shown use the rated lifting capacity of next longer boom
20
30˚ lengths or radius.
14.0 7) For boom length longer than 14 m, extend outriggers to the Max. or Mid. Extended.
8) For boom length longer than 23.8 m, extend outriggers to the Max. Extended.
15
9) Keep at least 3 wraps of load line on winch drum.
20˚ 10) 14 m boom means 1st mark on 2nd boom section side plate is half visible.
8.3
11) 18.9 m boom means 2nd mark on 2nd boom section side plate is half visible.
10 12) 23.8 m boom means 3rd mark on 2nd boom section side plate is half visible.
13) 28.6 m boom means 4th mark on 2nd boom section side plate is half visible.
10˚

0˚

0
0 5 10 15 20 25
Working Radius (m)

The above lifting heights and boom angles are based on a straight (unladen)boom, No. of part lines 1 2 4 6
and allowance should be made for boom deflection obtained under laden condition.
Max. of load 3,200kg 6,000kg 12,000kg 18,000kg

RATED LIFTING CAPACITY (IN KILOGRAMS) SAE85% / ISO4305

8.3m Boom 14m Boom 18.9m Boom 23.8m Boom 28.6m Boom 33.5m Boom

Load Load
radius radius
(m) Loaded Outriggers Loaded Outriggers Loaded Outriggers Loaded Outriggers Loaded Outriggers Loaded Outriggers (m)
Boom Extended Boom Extended Boom Extended Boom Extended Boom Extended Boom Extended
Angle Max. Mid. Min. Angle Max. Mid. Min. Angle Max. Mid. Angle Max. Mid. Angle Max. Angle Max.
1.5 79˚ 18,000 12,700 9,000 1.5
2.5 73˚ 11,300 11,300 6,500 2.5
3.0 68˚ 9,900 9,900 4,700 78˚ 7,200 7,200 4,300 3.0
3.5 64˚ 8,800 8,800 3,500 76˚ 7,200 7,200 3,400 3.5
4.0 60˚ 7,900 7,800 2,750 73˚ 7,200 7,200 2,700 4.0
5.0 51˚ 6,400 5,400 1,800 69˚ 6,200 5,400 1,850 75˚ 5,700 5,200 5.0
6.0 41˚ 5,200 3,750 1,200 65˚ 5,100 3,800 1,300 73˚ 4,700 3,600 77˚ 4,300 3,800 6.0
8.0 55˚ 3,700 2,200 650 66˚ 3,300 2,250 72˚ 3,200 2,250 77˚ 2,400 8.0
10.0 44˚ 2,600 1,450 300 59˚ 2,500 1,500 67˚ 2,400 1,500 72˚ 2,300 75˚ 1,700 10.0
12.0 29˚ 1,800 900 51˚ 2,000 1,000 61˚ 2,000 1,050 67˚ 1,900 71˚ 1,500 12.0
14.0 44˚ 1,500 650 56˚ 1,600 700 64˚ 1,600 69˚ 1,300 14.0
16.0 32˚ 1,100 400 50˚ 1,250 450 58˚ 1,300 65˚ 1,100 16.0
18.0 10˚ 750 41˚ 950 250 52˚ 1,000 60˚ 900 18.0
20.0 35˚ 700 48˚ 750 56˚ 750 20.0
22.0 21˚ 500 42˚ 550 52˚ 600 22.0
24.0 35˚ 400 47˚ 400 24.0
26.0 42˚ 250 26.0
2,900 2,100 550 1,000 650 250
0˚ 0˚ 0˚
(7.88m) (13.57m) (18.44m)
Notice : The chart is only for reference and should not be used for operation.
Maintain a clearances at least 3m between any part of the crane, load line or load and any electrical line carrying up to 50,000 volts.
0.3m additional clearance is required for every additional 30,000 volts or less.

< CAB BACK MOUNTED > < REAR MOUNTED >

Extension Mark Extension Mark for Rear Mout
Rear Stabilizers
Outriggers Max. Outriggers Min. Outriggers Max. Outriggers Min.
Front Outriggers Front Outriggers Rear Outriggers
Yellow: Extended Mid.
White: Extended Max. White: Extended Max.
Yellow: Extended Mid. Yellow: Extended Mid.
White: Extended Max. White: Extended Max.

Outriggers Mid.
Outriggers Mid.
Extended Min. Extended Min.
Extended Mid. Extended Max.
Extended Min. Extended Min.
Extended Max.
Extended Mid. Extended Mid.
Extended Max. Extended Max.

Courtesy of Crane.Market
TM-20110 (18 ton) crane configuration

<CAB BACK MOUNTED> (mm) Gross Axle Weight Rating(GAWR),front approx. 7,200 kg
Gross Axle Weight Rating(GAWR),rear approx. 15,400 kg
Gross Vehicle Weight Rating approx. 22,600 kg
Wheelbase(WB) 5,900 to 6,600 mm
Cab to axle 4,000 to 4,800 mm
Stability weight, front 3,900 kg Min (*)
Stability weight, rear 4,300 kg Min (*)
Frame Section Modulus(SM) 328 cm3 Min. per rail
under crane, front spring hunger of front
spring to rear spring hunger of rear spring
758 MPa steel
Frame Section Modulus(SM) 35 cm3 Min. per rail
5,900 to 6,600
at the front stabilizer attachment point,
3,900kg MIN 4,300kg MIN
758 MPa steel
Frame Section Modulus(SM) 213 cm3 Min. per rail
over rear stabilizers, 758 MPa steel
This mount requires front stabilizer, rear stabilizers, torsion
PTO torque Approx. 390 N-m Min.
resisting box and additional counterweight in the underside of
PTO revolution Approx. 550 to 2,400 min-1
the bed for full capacity 360˚ around the truck. Width for crane mounting Approx. 1,400 mm Min.
You must select a torsion box according to the length of the Frame width (outside) Approx. 915 mm Max.
flatbed and have it installed. The weight of standard torsion box Frame height (ground to frame top) Approx. 1,060 mm Max.
for 22' flat bed: approx. 1,814kg.The complete unit must be (Height of crane mounting base can be
istalled in accordance with factory requirements and a test changed by combination of jack floats
performed to determine actual stability and counterweight and crane bases)
requirements for variety of trucks. * Estimated axle scale weights prior to installation of crane, stabilizers and torsion resisting
CAB BACK MOUNTED product can not convert to REAR box for 78% stability. Include counterweight.
MOUNTED configuration.

<REAR MOUNTED> (mm) Gross Axle Weight Rating(GAWR), front approx. 6,350kg
Gross Axle Weight Rating(GAWR), rear approx. 15,400kg
Gross Vehicle Weight Rating approx. 21,750kg
Wheelbase(WB) 5,590 to 6,350mm
Cab to axle(CA) 3,810 to 4,570mm
Stability weight, front * 3,600kg Min.
Stability weight, rear * 3,600kg Min.
Frame Section Module(SM) under crane, 328 cm3 Min. per rail
110,000PSI steel
Frame Section Module(SM) 328 cm3 Min. per rail
over rear outriggers, 110,000PSI steel
PTO torque approx. 390 N-m Min.
5,590 to 6,350 PTO revolution approx. 550 to 2,400 rpm
*3,600kg MIN *3,600kg MIN Width for crane mounting approx. 1,400mm Min.
Frame width(outside) approx. 915mm Max.
Frame height(ground to frame top) approx. 1,060mm Max.
This mount requires front outriggers, torsion resisting box and
additional counterweight in the underside of the bed for full * Estimated axle scale weights prior to installation of crane, stabilisers and torsion box for 78%
capacity 360˚ around the truck. stabilitiy. Include counterweight.
You must select a torsion box according to the length of the flatbed and
have it installed. The weight of standard torsion box for 14' flat bed:
approx. 1,406kg.
The complete unit must be istalled in accordance with factory
requirements and a test performed to determine actual stability and
counterweight
requirements for variety of trucks.
REAR MOUNTED configulation can not convert to CAB BACK
MOUNTED configuration.

TM-20110 (18 ton) crane dimension specifications

(mm)

Min 8,330 Max33,530 2,428

450
2,809
stroke

Min 2,180
680

Mid 4,000
Max 5,700

Courtesy of Crane.Market
 Introducing the TADANO TM-20110, the TADANO Straight Truck Mount is available in behind
the cab as well as rear mounts. TADANO has over 50 years of experience in manufacturing high
quality cranes featuring innovative ideas and leading edge technology. The TM-20110 answers
a real need for a true Boom Truck for all over the world. This is the crane that everyone has been
looking for and we have delivered a crane packed with great features and superior performance.

With its long reach and high lift, we believe the TM-20110 is one of our most desirable cranes.
TADANO builds a vast range of cranes from 0.5 ton to 600 tons. No matter what your reach or lift
requirements are, TADANO can provide you with a great solution. Put one to work for you now.
Call today or visit our web site for more information.

Features:
Exceptional Reach without a Jib: 33.5 m. Full Power Boom
Self-Aligning Pentagonal Shaped Boom: reducing maintenance cost
Light Weight: increases payload
Out & Down Mainframe Outriggers: complete level ability
Multiple Outrigger Span: easy to set up in various job sites
Faster Function Speeds: increase productivity
Superior Winch Performance: up to 85 m/min increase productivity
Shear Plate Mounting: more secure “no creep mount”
Large Hydraulic Reservoir: superior cooling capabilities
Operator Friendly: dual control stations with exceptional job site viewing
Complete Load Monitoring: TADANO’s exclusive “AMA” system

Highest Quality Boom Trucks on the Planet

Continuing technical development requires Tadano to retain the right to

make specifications, equipment and price changes without notice. *Some specifications are subject to change

TADANO LTD. (International Division)

4-12, Kamezawa 2-chome, Sumida-ku Tokyo 130-0014, Japan
Phone: +81-3-3621-7750 Fax: +81-3-3621-7785
http://www.tadano.com E-mail: [email protected]
2014-05
Printed in Japan
Courtesy of Crane.Market
Powered by TCPDF (www.tcpdf.org)