CDX 30 MSDS
CDX 30 MSDS
1.2 Relevant identified uses of the substance or mixture and uses advised against
Use of the substance/ Marine engine oil.
mixture For specific application advice see appropriate Technical Data Sheet or consult our company
representative.
4.2 Most important symptoms and effects, both acute and delayed
See Section 11 for more detailed information on health effects and symptoms.
4.3 Indication of any immediate medical attention and special treatment needed
Notes to physician Treatment should in general be symptomatic and directed to relieving any effects.
6.2 Environmental Avoid dispersal of spilt material and runoff and contact with soil, waterways, drains and sewers.
precautions Inform the relevant authorities if the product has caused environmental pollution (sewers,
waterways, soil or air).
7.2 Conditions for safe Store in accordance with local regulations. Store in a dry, cool and well-ventilated area, away
storage, including any from incompatible materials (see Section 10). Keep away from heat and direct sunlight. Keep
incompatibilities container tightly closed and sealed until ready for use. Containers that have been opened must
be carefully resealed and kept upright to prevent leakage. Store and use only in equipment/
containers designed for use with this product. Do not store in unlabelled containers.
Not suitable Prolonged exposure to elevated temperature
Because specific work environments and material handling practices vary, safety procedures
should be developed for each intended application. The correct choice of protective gloves
depends upon the chemicals being handled, and the conditions of work and use. Most gloves
provide protection for only a limited time before they must be discarded and replaced (even the
best chemically resistant gloves will break down after repeated chemical exposures).
Gloves should be chosen in consultation with the supplier / manufacturer and taking account of
a full assessment of the working conditions.
Breakthrough time data are generated by glove manufacturers under laboratory test conditions
and represent how long a glove can be expected to provide effective permeation resistance. It
is important when following breakthrough time recommendations that actual workplace
conditions are taken into account. Always consult with your glove supplier for up-to-date
technical information on breakthrough times for the recommended glove type.
Our recommendations on the selection of gloves are as follows:
Continuous contact:
Gloves with a minimum breakthrough time of 240 minutes, or >480 minutes if suitable gloves
can be obtained.
If suitable gloves are not available to offer that level of protection, gloves with shorter
breakthrough times may be acceptable as long as appropriate glove maintenance and
replacement regimes are determined and adhered to.
Glove Thickness:
For general applications, we recommend gloves with a thickness typically greater than 0.35 mm.
It should be emphasised that glove thickness is not necessarily a good predictor of glove
resistance to a specific chemical, as the permeation efficiency of the glove will be dependent
on the exact composition of the glove material. Therefore, glove selection should also be based
on consideration of the task requirements and knowledge of breakthrough times.
Glove thickness may also vary depending on the glove manufacturer, the glove type and the
glove model. Therefore, the manufacturers’ technical data should always be taken into account
to ensure selection of the most appropriate glove for the task.
Note: Depending on the activity being conducted, gloves of varying thickness may be required
for specific tasks. For example:
• Thinner gloves (down to 0.1 mm or less) may be required where a high degree of manual
dexterity is needed. However, these gloves are only likely to give short duration protection and
would normally be just for single use applications, then disposed of.
Particle characteristics
Median particle size Not applicable.
9.2 Other information
No additional information.
10.3 Possibility of Under normal conditions of storage and use, hazardous reactions will not occur.
hazardous reactions Under normal conditions of storage and use, hazardous polymerisation will not occur.
10.4 Conditions to avoid Avoid all possible sources of ignition (spark or flame).
10.5 Incompatible materials Reactive or incompatible with the following materials: oxidising materials.
10.6 Hazardous Under normal conditions of storage and use, hazardous decomposition products should not be
decomposition products produced.
14.4 Packing - - - -
group
14.5 No. No. No. No.
Environmental
hazards
Additional - - - -
information
15.2 Chemical safety A Chemical Safety Assessment has been carried out for one or more of the substances within
assessment this mixture. A Chemical Safety Assessment has not been carried out for the mixture itself.
The data and advice given apply when the product is sold for the stated application or applications. You should not use the
product other than for the stated application or applications without seeking advice from BP Group.
It is the user’s obligation to evaluate and use this product safely and to comply with all applicable laws and regulations. The BP
Group shall not be responsible for any damage or injury resulting from use, other than the stated product use of the material,
from any failure to adhere to recommendations, or from any hazards inherent in the nature of the material. Purchasers of the
product for supply to a third party for use at work, have a duty to take all necessary steps to ensure that any person handling or
using the product is provided with the information in this sheet. Employers have a duty to tell employees and others who may be
affected of any hazards described in this sheet and of any precautions that should be taken. You can contact the BP Group to
ensure that this document is the most current available. Alteration of this document is strictly prohibited.