0% found this document useful (0 votes)
45 views2 pages

Nuvico NCT-5ML-E2 Quick Start Guide

Uploaded by

Ariam
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
45 views2 pages

Nuvico NCT-5ML-E2 Quick Start Guide

Uploaded by

Ariam
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

► Connecting Network Cable

NCT-5ML-E2 Eyeball Camera


Camera Quick start guide Tapping screw × 3
Quick Start Guide

CD Plastic plug ×3
■ Please read these instructions carefully before operating the unit Drill template

and keep it for further reference. 1 2 3


■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without notice.
Screwdriver
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through both
elements. Then crimp the cable with RJ 45 connector.

1 Warning and Caution


3 Overview ③ Connect the cable to the hermetic connector. Then tighten the nut
and the main cover.

■ If the product does not work properly, please contact your dealer or 1
the nearest service center. Never attempt to disassemble the camera
yourself. (We shall not be responsible for any problems caused by 2 4 Installation
unauthorized repair or maintenance.) 5
■ Do not allow water or liquid intrusion into the camera. 3 Please make sure that the wall or ceiling is strong enough to
■ In the use of the product, you must be in strict compliance with the 4 6 withstand 3 times the weight of the camera.
electrical safety regulations of the nation and region. When the product is ① Loosen the fixed screw to disassemble the camera.
mounted on wall or ceiling, the device shall be firmly fixed. ② Remove the cover from the dome to insert the SD card. Then,
■ Do not use camera beyond specified voltage range. install the cover back to the dome and fix it firmly with the screws.
1 Network connector 4 Fixed screw
■ Do not drop the camera or subject it to physical shock.
Note that the cover should not be installed unevenly. (Please skip this
2 Power connector Micro SD card slot*
■ Avoid touching the camera lens. 5
step if your camera has no micro SD card slot).
■ If cleaning is necessary, please use clean cloth to wipe it gently. 3 Mounting base 6 Reset*
■ Do not aim the camera at the sun or extra bright place. Cover
Note: Micro SD card slot and reset are optional. If no such interfaces, please Fixed Screw
■ Do not place the camera in extremely hot, cold (the operating Mounting Base
skip the above-mentioned(5, 6) instructions.
temperature shall be -22˚F~140˚F), dusty or damp locations, and do not Enclosure
C ap
expose it to high electromagnetic radiation. Se cu ri ty

■ To avoid heat accumulation, good ventilation is required for Dome


operating environment.

DC12V
③ Attach the drill template to the place where you want to fix the camera
and then drill the screw holes and the cable hole on the wall according to
the drill template.
2 Package * 1 It is recommended to install the security cap for outdoor installation.

* 2 If the PoE switch is used to power the camera that supports PoE power supply,
DC12V power supply is not required.
(mm)
Switch The default username is admin; the default password is 123456.
44.2

• Direct Access Through Web Browser


Ø91.6
Network Cable Network Cable MENU

IPC Router Computer

38.2
① Make sure that the camera and the PC are connected to the local
Ø51.0
network. Network Cable
MENU

IPC Computer
Ø4.5 ② Install Xcel IP Utility from the CD and run it after installation.

Device Network Search The default network settings are as shown below:
Immediate Refresh About
④ Route and connect the cables. Then secure the mounting base to the IP address: 192.168.226.201 HTTP:80
Device Name Device Type Product Model IP Address Http Port Data Port Subnet Modify Network Parameter
name IPC unknown 192.168.226.201 80 9008 255.255. Mac Address CE :98 :23 :75 :35 :22 Subnet Mask: 255.255.255.0 Data Port:9008
ceiling or wall with the screws provided. name IPC unknown 192.168.1.2 80 9008 255.255. IP Address 192 .168 . 226 . 201
name IPC unknown 192.168.1.3 80 9008 255.255. Subnet Mask 255 . 255 . 255 . 0 Gateway: 192.168.226.1
You may use the above default settings when you log in the camera for
Gateway 192 .168 . 226 . 1

Modify

i Tip: Enter the administrator password, and the first time.


then modify the network parameters.

Restore IPC Default Configuration


① Set the IP address of the PC and make sure the network segment is
the same as the default settings of IP Camera. Open the network and share
Total Device: 3 Local IP Address:192.168.1.4 Subnet Mask:255.255.255.0 Gateway: 192.168.1.1 DNS:210.21.196.6
center. Click “Local Area Connection” to pop up the following window.
Select “Properties” and then select Internet protocol according to the
③ Modify the IP address. The default IP address of this camera is actual situation (for example: IPv4). Next, click “Properties” button to set
⑤ Install the dome and enclosure to the mounting base and then adjust 192.168.226.201. Click the information of the camera listed in the above the network of the PC.
table to show the network information on the right hand. Modify the IP
the dome to obtain an optimum view angle. Finally, fix the camera with
address and gateway of the camera and make sure the network address is
the fixed screw.
in the same local network segment as the computer. Please modify the
IP address of your device according to the practical situation.

Modify Network Parameter

Mac Address CE :98 :23 :75 :35 :22


IP Address 192 .168 . 1 . 201
Subnet Mask 255 . 255 . 255 . 0
Gateway 192 .168 . 1 . 1

Modify

For example, the IP address of your computer is 192.168.1.4. So the


IP address of the camera shall be changed to 192.168.1.X. After ② Open a browser and enter the default address of IP Camera and
5 Network Connection modification, please enter the password of the administrator and click confirm.
“Modify” button to modify the setting. ③ Download and run the plugin in the computer.
In LAN, there are two ways to access the camera. 1. Access Through
The default password of the administrator is “123456”. ④ Enter the default username and password in the login interface to
Xcel IP Utility; 2. Direct Access Through Web Browser log in.
④ Double-click the IP address and then the system will pop up the web
browser to connect the IP camera. Follow directions to download and run the
• Access Through Xcel IP Utility plugin in the computer. Then enter the user name and password in the login
interface.
NCT-5ML-E2450043001057 A2

You might also like