St. Michael TVET Training and Assessment Center Inc.
(SMTTAC)
“Committed to Excellence and Quality Occupational Training as Foundation for Greater
Opportunities across the Globe”
TESDA-UTPRAS Registered and Accredited Assessment Center, PRC CPD Provider, and DepEd
Registered 3/F Pagkatipunan Building, Profugo Corner, Merchan St., Lucena City, Quezon
Province, 4301. Contact Number: 09106311644
JOINT DEVELOPMENT VOUCHER PROGRAM (JDVP)
(ELECTRONIC PRODUCTS ASSEMBLY AND SERVICING NCII)
Name of Trainee: ________________ Date:
Trainer: Kier Morales_
I. MUTIPLE CHOICES: Direction: Read the statement carefully. Encircle the letter of the correct
answer.
1. This is used to loosen or tighten screws with slotted heads?
A. Philip Screw Driver B. Stubby Screw Driver
C. Flat Screw Driver D. Allen Wrench
2. Its function is to drive screw with hexagonal slot head?
A. Philip Screw Driver B. Stubby Screw Driver
C. Flat Screw Driver D. Allen Wrench
3. Device used for joining metals permanently by applying heat to melt the solder. 4. This tool is used
to cut metal conduit and armored cable?
A. Soldering Iron B. Soldering Lead
C. De-Soldering Tools D. Soldering Pump
5. Used in removing soldered wires and components on the PCB?
A. Soldering Iron B. Soldering Lead
C. De-Soldering Tools D. Soldering Pump
6. This is the “filler metal” that are used in soldering?
A. Soldering Iron B. Soldering Lead
C. De-Soldering Tools D. Soldering Pump
7. Tool where the soldering iron is placed during usage?
A. Soldering Iron B. Soldering Lead
C. Soldering Stand D. Soldering Pump
8. Used in determining the size of wires/conductors?
A. Ruler B. Pull-Push Rule
C. Compass D. Wire Gauge
9. What are you going to use if you want to bore hole in the printed circuit board?
A. Mini drill B. Pliers
C. Claw Hammer D. Screw driver
10. What are you going to use in cleaning the circuit?
A. Cleaning Brush B. Towel
C. Ferric Chloride D. Running Water
11. A thin board made of fiberglass, composite epoxy or other laminate material with conductive
pathways or tracks that are used to connect different components?
A. Sand Paper B. Ferric Chloride
C. Printed Circuit Board D. Diagram
12. What are you going to is used to drive screws with cross slot heads?
A. Philip Screw Driver B. Stubby Screw Driver
C. Flat Screw Driver D. Allen Wrench
13. How can you maintain the tools and equipment in in good condition after you use it?
A. Clean the tools and equipment after use
B. Store the tools and equipment in storage after use.
C. Place it in the table without cleaning them.
D. What it with water
14. Electronic device that allows only one direction. Convert AC to pulsating DC?
A. Capacitor B. Transformer
C. Diode D. Resistor
15. Electronic device designed to limit the electrical current?
A. Capacitor B. Transformer
C. Diode D. Resistor
16. Capacitor is an Electronics devices used to store electrical charges, what is the symbol of Capacitor?
A. B.
C. D.
17. Small drawings or pictograms used to represent various electrical devices in a diagram or plan of
an electrical circuit?
A. Picture B. Symbols
C. Line D. Drawing
18. What are the first thing you that are going to do when you have to use a new Multi tester?
A. Read manual of instructions on how to operate the multi-tester.
B. Use the Multi tester already
C. Store the Multi tester to its proper storage
D. Place the Multi tester to table that are easily to reach by children
19. How can you identify if there is a Current in a Circuit?
A. Touch the wire using your bare hands.
B. Used a pliers to know if there is a current.
C. Call a Professional Technician.
D. Used a Multi tester.
20. What kind of equipment that you are going to use when you want to fastened and pulling out nails?
A. Claw Hammer B. Ballpeen Hammer
C. Mallet Hammer D. Boring Tool
II. IDENTIFICATION: Direction: Identify the following pictures that are given below. Write your
answer on the space before each number.
21. 26.
22. 27.
23. 28.
24. 29.
25. 30.
III. Direction: Answer the following question in English and Metric measurement.
31. 10 foot - inches 34. 16 galloon- Cups
32. 9 yards- foot 35. 10 tons - Pounds
33. 24 Hours - Seconds
Direction: Answer the following using OHMS LAW.
36. V= 15 V 37. V= 20 V
R= 10 ohms I= 5 A
I= R=
38. R= 54 V 39. V= 220 V
I= 2 A R= 55 ohms
V= I=
40. R= 120 V
I= 15 A
V=
Direction: Answer the following in Reading Voltage Scale.
43
41 44
42 45
41. Voltage scale 44. Voltage scale
Range -10V Range -10V
Reading= Reading=
42. Voltage scale
45. Voltage scale
Range -250V
Range -250V
Reading= Reading=
43. Voltage scale
Range -50V
Reading=
DIRECTION: Give the following Parts of a Multi-tester.
46.
48.
49.
47.
50.
GOOD LUCK 😊
