Ethernet HOWTO
Ethernet HOWTO
Linux Ethernet−Howto
Table of Contents
Linux Ethernet−Howto.......................................................................................................................................1
by Paul Gortmaker...................................................................................................................................1
1. Introduction..........................................................................................................................................1
2. Frequently Asked Questions................................................................................................................1
3. Performance Tips.................................................................................................................................1
4. Vendor/Manufacturer/Model Specific Information.............................................................................1
5. Cables, Coax, Twisted Pair..................................................................................................................3
6. Software Configuration and Card Diagnostics....................................................................................3
7. Technical Information..........................................................................................................................3
8. Miscellaneous......................................................................................................................................3
1. Introduction.........................................................................................................................................3
1.1 New Versions of this Document.......................................................................................................4
1.2 Using the Ethernet−Howto...............................................................................................................4
1.3 What do I need to to get ethernet working?.......................................................................................5
1.4 HELP − It doesn't work!...................................................................................................................5
1.5 Type of cable that your card should support.....................................................................................7
2. Frequently Asked Questions...............................................................................................................7
2.1 How do I tell Linux what driver to use?...........................................................................................7
2.2 What card should I buy for Linux?...................................................................................................8
2.3 Alpha Drivers −− Getting and Using them.......................................................................................8
2.4 Using More than one Ethernet Card per Machine............................................................................9
With the Driver as a Module.............................................................................................................9
With the Driver Compiled into the Kernel......................................................................................10
2.5 The ether= thing didn't do anything for me. Why?..........................................................................11
2.6 Problems with NE1000 / NE2000 cards (and clones)....................................................................11
2.7 Problems with SMC Ultra/EtherEZ and WD80*3 cards................................................................15
2.8 Problems with 3Com cards.............................................................................................................16
2.9 FAQs Not Specific to Any Card......................................................................................................17
Linux and ISA Plug and Play Ethernet Cards.................................................................................17
PCI machine detects card but driver fails probe (PnP OS).............................................................18
All cards detected but two fail to work in PCI machine.................................................................18
I have /etc/conf.modules and not /etc/modules.conf.......................................................................18
Ethercard is Not Detected at Boot...................................................................................................18
Driver reports unresolved symbol ei_open and won't load.............................................................19
ifconfig reports the wrong I/O address for the card........................................................................19
Shared Memory ISA cards in PCI Machine do not work (0xffff)...................................................19
Card seems to send data but never receives anything.....................................................................19
Asynchronous Transfer Mode (ATM) Support...............................................................................19
Gigabit Ethernet Support.................................................................................................................20
FDDI Support..................................................................................................................................20
Full Duplex Support........................................................................................................................20
Ethernet Cards for Linux on SMP Machines..................................................................................20
Ethernet Cards for Linux on Alpha/AXP PCI Boards....................................................................22
Ethernet for Linux on SUN/Sparc Hardware..................................................................................22
Ethernet for Linux on Other Hardware...........................................................................................22
Linking 10 or 100 BaseT without a Hub.........................................................................................23
SIOCSIFxxx: No such device.........................................................................................................23
SIOCSFFLAGS: Try again.............................................................................................................23
i
Linux Ethernet−Howto
Table of Contents
Linux Ethernet−Howto
Using `ifconfig' and Link UNSPEC with HW−addr of 00:00:00:00:00:00....................................23
Huge Number of RX and TX Errors...............................................................................................23
Entries in /dev/ for Ethercards.........................................................................................................24
Access to the raw Ethernet Device..................................................................................................24
3. Performance Tips..............................................................................................................................24
3.1 General Concepts.............................................................................................................................24
3.2 ISA Cards and ISA Bus Speed.........................................................................................................25
3.3 Setting the TCP Rx Window...........................................................................................................25
3.4 Increasing NFS performance...........................................................................................................26
4. Vendor/Manufacturer/Model Specific Information..........................................................................26
4.1 3Com...............................................................................................................................................27
3c501..............................................................................................................................................27
EtherLink II, 3c503, 3c503/16.......................................................................................................27
Etherlink Plus 3c505......................................................................................................................28
Etherlink−16 3c507........................................................................................................................28
Etherlink III, 3c509 / 3c509B.........................................................................................................28
3c515..............................................................................................................................................29
3c523..............................................................................................................................................29
3c527 Etherlink MC/32..................................................................................................................29
3c529..............................................................................................................................................29
3c339 Token Ring PCI Velocity XL...............................................................................................30
3c556...............................................................................................................................................30
3c562...............................................................................................................................................30
3c575...............................................................................................................................................30
3c579..............................................................................................................................................30
3c589 / 3c589B...............................................................................................................................30
3c590 / 3c595.................................................................................................................................30
3c592 / 3c597..................................................................................................................................31
3c900 / 3c905 / 3c905B / 3c905C / 3c905CX.................................................................................31
3c985 (Gigabit acenic, aka Tigon2)................................................................................................31
3c996 (Gigabit broadcom, aka Tigon3)..........................................................................................31
4.2 Accton.............................................................................................................................................31
Accton MPX....................................................................................................................................31
Accton EN1203, EN1207, EtherDuo−PCI......................................................................................32
Accton EN2209 Parallel Port Adaptor (EtherPocket).....................................................................32
Accton EN2212 PCMCIA Card......................................................................................................32
4.3 Adaptec............................................................................................................................................32
Adaptec DuraLAN/Starfire, 64bit ANA−6922...............................................................................32
4.4 Allied Telesyn/Telesis....................................................................................................................32
AT1500...........................................................................................................................................32
AT1700...........................................................................................................................................32
AT2400...........................................................................................................................................33
AT2450...........................................................................................................................................33
AT2500............................................................................................................................................33
AT2540FX......................................................................................................................................33
4.5 AMD / Advanced Micro Devices...................................................................................................33
AMD LANCE (7990, 79C960/961/961A, PCnet−ISA)................................................................33
ii
Linux Ethernet−Howto
Table of Contents
Linux Ethernet−Howto
AMD 79C901 (Home PNA PHY)...................................................................................................34
AMD 79C965 (PCnet−32).............................................................................................................34
AMD 79C970/970A (PCnet−PCI).................................................................................................35
AMD 79C971 (PCnet−FAST)........................................................................................................35
AMD 79C972 (PCnet−FAST+)......................................................................................................35
AMD 79C974 (PCnet−SCSI)..........................................................................................................35
4.6 Ansel Communications...................................................................................................................35
AC3200 EISA..................................................................................................................................35
4.7 Apricot.............................................................................................................................................35
Apricot Xen−II On Board Ethernet.................................................................................................36
4.8 Arcnet..............................................................................................................................................36
4.9 Boca Research.................................................................................................................................36
Boca BEN400..................................................................................................................................36
Boca BEN (ISA, VLB, PCI)..........................................................................................................36
4.10 Broadcom.......................................................................................................................................37
Broadcom Tigon2............................................................................................................................37
Broadcom Tigon3............................................................................................................................37
4.11 Cabletron.......................................................................................................................................37
E10**, E10**−x, E20**, E20**−x................................................................................................37
E2100..............................................................................................................................................37
E22**..............................................................................................................................................38
4.12 Cogent............................................................................................................................................38
EM100−ISA/EISA..........................................................................................................................38
Cogent eMASTER+, EM100−PCI, EM400, EM960, EM964........................................................38
4.13 Compaq..........................................................................................................................................38
Compaq Deskpro / Compaq XL (Embedded AMD Chip)..............................................................38
Compaq Nettelligent/NetFlex (Embedded ThunderLAN Chip).....................................................39
Compaq PCI card............................................................................................................................39
4.14 Danpex...........................................................................................................................................39
Danpex EN9400..............................................................................................................................39
4.15 Davicom.........................................................................................................................................39
Davicom DM9102...........................................................................................................................39
4.16 D−Link..........................................................................................................................................39
DE−100, DE−200, DE−220−T, DE−250.......................................................................................39
DE−520..........................................................................................................................................40
DE−528...........................................................................................................................................40
DE−530..........................................................................................................................................40
DE−600..........................................................................................................................................40
DE−620..........................................................................................................................................40
DE−650..........................................................................................................................................40
DFE−530TX....................................................................................................................................40
DFE−530TX+, DFE−538TX..........................................................................................................41
DFE−550TX....................................................................................................................................41
DFE−570TX....................................................................................................................................41
DFE−580TX....................................................................................................................................41
DGE−500T......................................................................................................................................41
DGE−550T......................................................................................................................................41
iii
Linux Ethernet−Howto
Table of Contents
Linux Ethernet−Howto
4.17 DFI................................................................................................................................................41
DFINET−300 and DFINET−400...................................................................................................41
4.18 Digital / DEC................................................................................................................................41
DEPCA, DE100/1, DE200/1/2, DE210, DE422............................................................................41
Digital EtherWorks 3 (DE203, DE204, DE205)............................................................................42
DE425 EISA, DE434, DE435, DE500...........................................................................................42
DEC 21040, 21041, 2114x, Tulip..................................................................................................42
4.19 Farallon..........................................................................................................................................43
Farallon Etherwave..........................................................................................................................43
Farallon PCI 593.............................................................................................................................43
4.20 Fujitsu............................................................................................................................................44
Fujitsu FMV−181/182/183/184.......................................................................................................44
4.21 Hewlett Packard............................................................................................................................44
HP Night Director+ 10/100.............................................................................................................44
27245A...........................................................................................................................................44
HP EtherTwist, PC Lan+ (27247, 27248, 27252A, 27269B).........................................................44
HP−J2405A.....................................................................................................................................44
HP−Vectra On Board Ethernet........................................................................................................45
HP 10/100 VG Any Lan Cards (27248B, J2573, J2577, J2585, J970, J973).................................45
HP NetServer 10/100TX PCI (D5013A).........................................................................................45
4.22 IBM / International Business Machines........................................................................................45
IBM Thinkpad 300.........................................................................................................................45
IBM Credit Card Adaptor for Ethernet...........................................................................................45
IBM 10/100 EtherJet PCI................................................................................................................45
IBM Token Ring.............................................................................................................................45
4.23 ICL Ethernet Cards........................................................................................................................46
ICL EtherTeam 16i/32.....................................................................................................................46
4.24 Intel Ethernet Cards......................................................................................................................46
Ether Express...................................................................................................................................46
Ether Express PRO/10 (PRO/10+)..................................................................................................46
Ether Express PRO/10 PCI (EISA).................................................................................................46
Ether Express PRO 10/100B..........................................................................................................47
E1000 Gigabit..................................................................................................................................47
4.25 Kingston.........................................................................................................................................47
4.26 LinkSys..........................................................................................................................................47
LinkSys Etherfast 10/100 Cards......................................................................................................47
LinkSys Pocket Ethernet Adapter Plus (PEAEPP).........................................................................47
LinkSys PCMCIA Adaptor.............................................................................................................48
4.27 Microdyne (Eagle).........................................................................................................................48
Microdyne Exos 205T.....................................................................................................................48
4.28 Mylex.............................................................................................................................................48
Mylex LNE390A, LNE390B..........................................................................................................48
Mylex LNP101................................................................................................................................48
Mylex LNP104................................................................................................................................49
4.29 Myson............................................................................................................................................49
Myson MTD−8xx 10/100 PCI........................................................................................................49
4.30 National Semiconductor.................................................................................................................49
iv
Linux Ethernet−Howto
Table of Contents
Linux Ethernet−Howto
NS8390, DP8390, DP83905 etc......................................................................................................49
DP83800 with DP83840..................................................................................................................49
DP83815/83816...............................................................................................................................49
NS83820, DP83820.........................................................................................................................49
4.31 Novell Ethernet, NExxxx and associated clones..........................................................................50
NE1000, NE2000...........................................................................................................................50
NE2000−PCI (RealTek/Winbond/Compex)..................................................................................50
NE−10/100......................................................................................................................................51
NE1500, NE2100...........................................................................................................................51
NE/2 MCA......................................................................................................................................51
NE3200...........................................................................................................................................52
NE3210...........................................................................................................................................52
NE4100............................................................................................................................................52
NE5500............................................................................................................................................52
4.32 Netgear...........................................................................................................................................52
Netgear FA−311..............................................................................................................................52
Netgear GA−620.............................................................................................................................52
Netgear GA−621.............................................................................................................................52
4.33 Proteon...........................................................................................................................................52
Proteon P1370−EA..........................................................................................................................52
Proteon P1670−EA..........................................................................................................................53
4.34 Pure Data........................................................................................................................................53
PDUC8028, PDI8023......................................................................................................................53
4.35 Racal−Interlan................................................................................................................................53
ES3210............................................................................................................................................53
NI5010.............................................................................................................................................53
NI5210.............................................................................................................................................53
NI6510 (not EB).............................................................................................................................54
EtherBlaster (aka NI6510EB).........................................................................................................54
4.36 RealTek..........................................................................................................................................54
RealTek RTL8002/8012 (AT−Lan−Tec) Pocket adaptor..............................................................54
RealTek 8008..................................................................................................................................54
RealTek 8009..................................................................................................................................54
RealTek 8019..................................................................................................................................55
RealTek 8029..................................................................................................................................55
RealTek 8129/8139........................................................................................................................55
4.37 Sager..............................................................................................................................................55
Sager NP943....................................................................................................................................55
4.38 Schneider & Koch..........................................................................................................................55
SK G16............................................................................................................................................55
4.39 SEEQ.............................................................................................................................................56
SEEQ 8005......................................................................................................................................56
4.40 SiS (Silicon Integrated Systems)...................................................................................................56
SiS 900 (7016, 630E, 962)..............................................................................................................56
4.41 SMC (Standard Microsystems Corp.)...........................................................................................56
WD8003, SMC Elite.......................................................................................................................56
WD8013, SMC Elite16..................................................................................................................57
v
Linux Ethernet−Howto
Table of Contents
Linux Ethernet−Howto
SMC Elite Ultra..............................................................................................................................57
SMC Elite Ultra32 EISA................................................................................................................58
SMC EtherEZ (8416)......................................................................................................................58
SMC EtherPower PCI (8432).........................................................................................................58
SMC EtherPower II PCI (9432).....................................................................................................59
SMC 1211TX 10/100......................................................................................................................59
SMC 3008........................................................................................................................................59
SMC 3016........................................................................................................................................59
SMC−9000 / SMC 91c92/4.............................................................................................................59
SMC 91c100....................................................................................................................................60
SMC 9452TX/9462TX....................................................................................................................60
4.42 Sundance........................................................................................................................................60
Sundance ST201, Alta.....................................................................................................................60
4.43 SysKonnect....................................................................................................................................60
SysKonnect sk−98xx Gigabit Ethernet...........................................................................................60
4.44 Texas Instruments..........................................................................................................................60
ThunderLAN..................................................................................................................................60
4.45 Thomas Conrad..............................................................................................................................60
Thomas Conrad TC−5048...............................................................................................................60
4.46 VIA................................................................................................................................................61
VIA 86C926 Amazon......................................................................................................................61
VIA 86C100A Rhine II (and 3043 Rhine I)...................................................................................61
4.47 Western Digital..............................................................................................................................61
4.48 Winbond.........................................................................................................................................61
Winbond 89c840.............................................................................................................................61
Winbond 89c904, 89c905, 89c906..................................................................................................61
Winbond 89c940.............................................................................................................................62
4.49 Xircom..........................................................................................................................................62
Xircom PE1, PE2, PE3−10B*.........................................................................................................62
Xircom CE, CEM, CE2, CE3..........................................................................................................62
Xircom CBE−100............................................................................................................................62
4.50 Zenith............................................................................................................................................62
Z−Note...........................................................................................................................................62
4.51 Znyx..............................................................................................................................................63
Znyx ZX342 (DEC 21040 based)...................................................................................................63
4.52 Identifying an Unknown Card......................................................................................................63
Identifying the Network Interface Controller..................................................................................63
Identifying the Ethernet Address.....................................................................................................64
Identifying the Card by the FCC ID Number..................................................................................64
Tips on Trying to Use an Unknown Card.......................................................................................64
4.53 Drivers for Non−Ethernet Devices................................................................................................65
5. Cables, Coax, Twisted Pair...............................................................................................................65
5.1 Thin Ethernet (thinnet)....................................................................................................................66
5.2 Twisted Pair....................................................................................................................................66
6. Software Configuration and Card Diagnostics.................................................................................66
6.1 Configuration Programs for Ethernet Cards...................................................................................67
WD80x3 Cards................................................................................................................................67
vi
Linux Ethernet−Howto
Table of Contents
Linux Ethernet−Howto
Digital / DEC Cards........................................................................................................................67
NE2000+ or AT/LANTIC Cards.....................................................................................................67
3Com Cards.....................................................................................................................................68
6.2 Diagnostic Programs for Ethernet Cards........................................................................................68
7. Technical Information.......................................................................................................................68
7.1 Programmed I/O vs. Shared Memory vs. DMA.............................................................................68
Programmed I/O (e.g. NE2000, 3c509)..........................................................................................69
Shared memory (e.g. WD80x3, SMC−Ultra, 3c503)......................................................................69
Bus Master Direct Memory Access (e.g. LANCE, DEC 21040)....................................................69
7.2 Performance Implications of Bus Width..........................................................................................69
ISA Eight bit and ISA 16 bit Cards.................................................................................................69
32 Bit PCI (VLB/EISA) Ethernet Cards.........................................................................................70
7.3 Performance Implications of Zero Copy..........................................................................................70
7.4 Performance Implications of Hardware Checksums........................................................................70
7.5 Performance Implications of NAPI (Rx interrupt mitigation).........................................................70
8. Miscellaneous...................................................................................................................................71
8.1 Transmit FIFO Buffers and Underrun Errors..................................................................................71
8.2 Passing Ethernet Arguments to the Kernel.....................................................................................71
The ether command........................................................................................................................72
The reserve command....................................................................................................................72
8.3 Using the Ethernet Drivers as Modules..........................................................................................73
8.4 Related Documentation....................................................................................................................74
8.5 Disclaimer and Copyright...............................................................................................................75
8.6 Closing.............................................................................................................................................75
vii
Linux Ethernet−Howto
by Paul Gortmaker
v2.9, Aug 25, 2003
This is the Ethernet−Howto, which is a compilation of information about which ethernet devices can be used
for Linux, and how to set them up. Note that this Howto is focused on the hardware and low level driver
aspect of the ethernet cards, and does not cover the software end of things like ifconfig and route. That
information is found in various other Linux documentation.
1. Introduction
• 1.1 New Versions of this Document
• 1.2 Using the Ethernet−Howto
• 1.3 What do I need to to get ethernet working?
• 1.4 HELP − It doesn't work!
• 1.5 Type of cable that your card should support
3. Performance Tips
• 3.1 General Concepts
• 3.2 ISA Cards and ISA Bus Speed
• 3.3 Setting the TCP Rx Window
• 3.4 Increasing NFS performance
Linux Ethernet−Howto 1
Linux Ethernet−Howto
• 4.7 Apricot
• 4.8 Arcnet
• 4.9 Boca Research
• 4.10 Broadcom
• 4.11 Cabletron
• 4.12 Cogent
• 4.13 Compaq
• 4.14 Danpex
• 4.15 Davicom
• 4.16 D−Link
• 4.17 DFI
• 4.18 Digital / DEC
• 4.19 Farallon
• 4.20 Fujitsu
• 4.21 Hewlett Packard
• 4.22 IBM / International Business Machines
• 4.23 ICL Ethernet Cards
• 4.24 Intel Ethernet Cards
• 4.25 Kingston
• 4.26 LinkSys
• 4.27 Microdyne (Eagle)
• 4.28 Mylex
• 4.29 Myson
• 4.30 National Semiconductor
• 4.31 Novell Ethernet, NExxxx and associated clones.
• 4.32 Netgear
• 4.33 Proteon
• 4.34 Pure Data
• 4.35 Racal−Interlan
• 4.36 RealTek
• 4.37 Sager
• 4.38 Schneider & Koch
• 4.39 SEEQ
• 4.40 SiS (Silicon Integrated Systems)
• 4.41 SMC (Standard Microsystems Corp.)
• 4.42 Sundance
• 4.43 SysKonnect
• 4.44 Texas Instruments
• 4.45 Thomas Conrad
• 4.46 VIA
• 4.47 Western Digital
• 4.48 Winbond
• 4.49 Xircom
• 4.50 Zenith
• 4.51 Znyx
• 4.52 Identifying an Unknown Card
• 4.53 Drivers for Non−Ethernet Devices
Linux Ethernet−Howto 2
Linux Ethernet−Howto
7. Technical Information
• 7.1 Programmed I/O vs. Shared Memory vs. DMA
• 7.2 Performance Implications of Bus Width
• 7.3 Performance Implications of Zero Copy
• 7.4 Performance Implications of Hardware Checksums
• 7.5 Performance Implications of NAPI (Rx interrupt mitigation)
8. Miscellaneous.
• 8.1 Transmit FIFO Buffers and Underrun Errors
• 8.2 Passing Ethernet Arguments to the Kernel
• 8.3 Using the Ethernet Drivers as Modules
• 8.4 Related Documentation
• 8.5 Disclaimer and Copyright
• 8.6 Closing
1. Introduction
The Ethernet−Howto contains detailed information on the current level of support for most of the common
ethernet cards available. It covers common hardware configuration problems, and problems associated with
choosing the right driver, and then getting that driver loaded and functional. It does not cover the next stages
of setup (choosing an internet address, routing, etc). That information can be found in various other Linux
documentation.
In the early days of linux, the old ISA type ethernet cards were the norm. The ISA bus had no sane or safe
way for linux to determine what cards were installed, or what settings each card was to use. This meant that
the end user was more involved in supplying this information to linux, and they turned to this guide for help
on doing this.
Fortunately, the newer PCI bus can be found in nearly every computer that is out there today, and the ISA bus
is left to collect dust with the 386 and 486 computers of yesteryear. The designers of the PCI bus recognized
the problem with card detection on the old ISA bus, and so added support for each card to be able to
communicate to the host computer their manufacturer and model, and what settings are to be used.
This slow demise of the ISA bus has reduced the involvement of the end user drastically. As such, most of
today's linux users would not need to turn to this guide for help. However there are always some corner cases
where things don't work as expected, or some problems that need troubleshooting. And of course there are still
some old ISA computers out there doing thankless dedicated tasks in the bottom of dark closets too.
This present revision covers ethernet drivers found in kernels up to and including version 2.4.21. Some
features pertaining to the upcoming 2.6 release are also mentioned.
The primary source of information for the initial ASCII−only version of the Ethernet−Howto was:
who we should thank for writing a lot of the ethernet card drivers that are presently available for Linux.
This document is Copyright (c) 1993−2003 by Paul Gortmaker. Yes, I have been maintaing this thing for 10
years now! Please see the Disclaimer and Copying information at the end of this document ( copyright) for
information about redistribution of this document and the usual `we are not responsible for what you manage
to break...' type legal stuff.
Ethernet−HOWTO
This is the `official' location − it can also be found on various Linux WWW/ftp mirror sites. Updates will be
made as new information and/or drivers becomes available. If this copy that you are reading is more than 6
months old, then you should check to see if an updated copy is available.
This document is available in various formats (postscript, dvi, ASCII, HTML, etc.). I would recommend
viewing it in HTML (via a WWW browser) or the Postscript/dvi format. Both of these contain
cross−references that are not included in the plain text ASCII format.
Chances are you are reading this document beacuse you can't get things to work and you don't know what to
do or check. The next section ( HELP − It doesn't work!) is aimed at newcomers to linux and will point you in
the right direction.
Typically the same problems and questions are asked over and over again by different people. Chances are
your specific problem or question is one of these Frequently Asked Questions, and is answered in the FAQ
portion of this document . ( The FAQ section). Everybody should have a look through this section before
posting for help.
If you haven't got an ethernet card, then you will want to start with deciding on a card. ( What card should I
buy...)
If you have already got an ethernet card, but are not sure if you can use it with Linux, then you will want to
read the section which contains specific information on each manufacturer, and their cards. ( Vendor
Specific...)
If you are interested in some of the technical aspects of the Linux device drivers, then you can have a browse
of the section with this type of information. ( Technical Information)
First thing you need to do is figure out what model your card is so you can determine if Linux has a driver for
that particular card. Different cards typically have different ways of being controlled by the host computer,
and the linux driver (if there is one) contains this control information in a format that allows linux to use the
card.
If you don't have any manuals or anything of the sort that tell you anything about the card model, then you can
try using the lspci utility for obtaining information on the PCI devices in your computer. Doing a cat
/proc/pci gives similar (but less) information. For ISA cards, see the section on helping with mystery
cards (reference section: Identifying an Unknown Card).
Now that you know what type of card you have, read through the details of your particular card in the card
specific section (reference section: Vendor Specific...) which lists in alphabetical order, card manufacturers,
individual model numbers and whether it has a linux driver or not. If it lists it as `Not Supported' you can
pretty much give up here. If you can't find your card in that list, then check to see if your card manual lists it
as being `compatible' with another known card type. For example there are hundreds, if not thousands of
different cards made to be compatible with the original Novell NE2000 design.
Assuming you have found out that a linux driver exists for your card, you now have to find it and make use of
it. Just because linux has a driver for your card does not mean that it is built into every kernel. (The kernel is
the core operating system that is first loaded at boot, and contains drivers for various pieces of hardware,
among other things.) Depending on who made the particular linux distribution you are using, there may be
only a few pre−built kernels, and a whole bunch of drivers as smaller separate modules, or there may be a
whole lot of kernels, covering a vast combination of built−in driver combinations.
If you didn't find either a pre−built kernel with your driver, or a module form of the driver, chances are you
have a typically uncommon card, and you will have to build your own kernel with that driver included. Once
you have linux installed, building a custom kernel is not difficult at all. You essentially answer yes or no to
what you want the kernel to contain, and then tell it to build it. There is a Kernel−HowTo that will help you
along.
At this point you should have somehow managed to be booting a kernel with your driver built in, or be
loading it as a module. About half of the problems people have are related to not having driver loaded one
way or another, so you may find things work now.
If it still doesn't work, then you need to verify that the kernel is indeed detecting the card. To do this, you need
to type dmesg | more when logged in after the system has booted and all modules have been loaded. This
will allow you to review the boot messages that the kernel scrolled up the screen during the boot process. If
the card has been detected, you should see somewhere in that list a message from your card's driver that starts
with eth0, mentions the driver name and the hardware parameters (interrupt setting, input/output port
address, etc) that the card is set for. (Note: At boot, linux lists all the PCI cards installed in the system,
regardless of what drivers are available − do not mistake this for the driver detection which comes later!)
If you don't see a driver indentification message like this, then the driver didn't detect your card, and that is
why things aren't working. See the FAQ ( The FAQ Section) for what to do if your card is not detected. If you
have a NE2000 compatible, there is also some NE2000 specific tips on getting a card detected in the FAQ
section as well.
If the card is detected, but the detection message reports some sort of error, like a resource conflict, then the
driver probably won't have initialized properly and the card still wont be useable. Most common error
messages of this sort are also listed in the FAQ section, along with a solution.
If the detection message seems okay, then double check the card resources reported by the driver against those
that the card is physically set for (either by little black jumpers on the card, or by a software utility supplied by
the card manufacturer.) These must match exactly. For example, if you have the card jumpered or configured
to IRQ 15 and the driver reports IRQ 10 in the boot messages, things will not work. The FAQ section
discusses the most common cases of drivers incorrectly detecting the configuration information of various
cards.
At this point, you have managed to get you card detected with all the correct parameters, and hopefully
everything is working. If not, then you either have a software configuration error, or a hardware configuration
error. A software configuration error is not setting up the right network addresses for the ifconfig and
route commands, and details of how to do that are fully described in the Network HowTo and the `Network
Administrator's Guide' which both probably came on the CD−ROM you installed from.
A hardware configuration error is when some sort of resource conflict or mis−configuration (that the driver
didn't detect at boot) stops the card from working properly. This typically can be observed in several different
ways. (1) You get an error message when ifconfig tries to open the device for use, such as
``SIOCSFFLAGS: Try again''. (2) The driver reports eth0 error messages (viewed by dmesg | more) or
strange inconsistencies for each time it tries to send or receive data. (3) Typing cat /proc/net/dev
Well, if you have got to this point and things still aren't working, read the FAQ section of this document, read
the vendor specific section detailing your particular card, and if it still doesn't work then you may have to
resort to posting to an appropriate newsgroup for help. If you do post, please detail all relevant information in
that post, such as the card brand, the kernel version, the driver boot messages, the output from cat
/proc/net/dev, a clear description of the problem, and of course what you have already tried to do in an
effort to get things to work.
You would be surprised at how many people post useless things like ``Can someone help me? My ethernet
doesn't work.'' and nothing else. Readers of the newsgroups tend to ignore such silly posts, whereas a detailed
and informational problem description may allow a `linux−guru' to spot your problem right away. Of course
the same holds true when e−mailing a problem report − always provide as much information as possible.
The thinnet, or thin ethernet cabling, (RG−58 coaxial cable) with the BNC (metal push and turn−to−lock)
connectors is technically called 10Base2.
The older thick ethernet (10mm coaxial cable) which is only found in older installations is called 10Base5.
The 15 pin D−shaped plug found on some ethernet cards (the AUI connector) is used to connect to thick
ethernet and external transcievers.
Most ethercards also come in a `Combo' version for only $10−$20 more. These have both twisted pair and
thinnet transceiver built−in, allowing you to change your mind later.
Most installations will use 10BaseT/100BaseT 10Base2 does not offer any upgrade path to
100Base−whatever. 10Base2 is fine for hobbyists setting up a home network when purchasing a hub is not
desireable for some reason or another.
See Cables, Coax... for other concerns with different types of ethernet cable.
for each card in this document. Once you know the name of the module, you have to add it to the file
/etc/modules.conf so Linux will know what module to load for your card. The syntax is typically as
follows.
The options line is typically only needed for older ISA hardware. For multiple card systems, additional lines
with eth1, eth2 and so on are usually required.
The module files typically live in the directory /lib/modules/ which is further subdivided by kernel
version (use uname −r) and subsystem (in this case net). These are put there by the distribution builder, or
by the individual user when they run make modules_install after building their own kernel and
modules (see the kernel howto for more details on building your own stuff).
If you build your own kernel, you have the option of having all the drivers merged with the kernel right then
and there, rather than existing as separate files. When this is done, the drivers will detect the hardware at boot
up. Options to the drivers are supplied by the kernel command line prior to boot (see BootPrompt Howto for
more details). The user chooses what drivers are used during the make config step of building the kernel
(again see the kernel howto).
If you only expect a single user to be doing the occasional ftp session or WWW connection, then even an old
ISA card will probably keep you happy (assuming 10Mbps, not 100).
If you intend to set up a server, and you require the CPU overhead of moving data over the network to be kept
to a minimum, you probably want to look at one of the PCI cards that uses a chip with bus−mastering
capapbility. In addition, some cards now can actually do some of the processing overhead of data checksums
right on the card, giving the CPU even more of a break. For more details please see:
If you fall somewhere in the middle of the above, then any one of the low cost PCI cards with a stable driver
will do the job for you.
The newest of the `new' drivers can be found on Donald's WWW site: www.scyld.com − things change
here quite frequently, so just look around for it. Alternatively, it may be easier to use a WWW browser on:
to locate the driver that you are looking for. (Watch out for WWW browsers that silently munge the source by
replacing TABs with spaces and so on − use ftp, or at least an FTP URL for downloading if unsure.)
Note that some of the `useable' experimental/alpha drivers have been included in the standard kernel source
tree. When running make config one of the first things you will be asked is whether to ``Prompt for
development and/or incomplete code/drivers''. You will have to answer `Y' here to get asked about including
any alpha/experiemntal drivers.
The answer to this question depends on whether the driver(s) is/are being used as a loadable module or are
compiled directly into the kernel. Most linux distributions use modular drivers now. This saves distributing
lots of kernels, each with a different driver set built in. Instead a single basic kernel is used and the individual
drivers that are need for a particular user's system are loaded once the system has booted far enough to access
the driver module files (usually stored in /lib/modules/).
In the case of PCI cards, the PCI drivers/modules should detect all of the installed cards that it supports
automatically. The user should not supply any I/O base or IRQ information, unless specifically instructed to
do so by the individual driver documentation in order to support some non−standard machine.
Some earlier kernels had a limit of 16 ethercards that could be detected at boot, and some ISA modules have a
limit of four cards per loaded module. You can always load another copy of the same module under a different
name to support another four cards if this is a limitation, or recompile the module with support for as many as
you require.
As an example, consider a user that has two ISA NE2000 cards, one at 0x300 and one at 0x240 and what
lines they would have in their /etc/modules.conf file:
alias eth0 ne
alias eth1 ne
options ne io=0x240,0x300
What this does: This says that if the administrator (or the kernel) does a modprobe eth0 or a modprobe
eth1 then the ne.o driver should be loaded for either eth0 or eth1. Furthermore, when the ne.o module
is loaded, it should be loaded with the options io=0x240,0x300 so that the driver knows where to look for
the cards. Note that the 0x is important − things like 300h as commonly used in the DOS world won't work.
Switching the order of the 0x240 and the 0x300 will switch which physical card ends up as eth0 and
eth1.
Most of the ISA module drivers can take multiple comma separated I/O values like this example to handle
multiple cards. However, some (older?) drivers, such as the 3c501.o module are currently only able to handle
one card per module load. In this case you can load the module twice to get both cards detected. The
/etc/modules.conf file in this case would look like:
In this example the −o option has been used to give each instance of the module a unique name, since you
can't have two modules loaded with the same name. The irq= option has also been used to to specify the
hardware IRQ setting of the card. (This method can also be used with modules that accept comma separated
I/O values, but it is less efficient since the module ends up being loaded twice when it doesn't really need to
be.)
As a final example, consider a user with one 3c503 card at 0x350 and one SMC Elite16 (wd8013) card at
0x280. They would have:
alias eth0 wd
alias eth1 3c503
options wd io=0x280
options 3c503 io=0x350
For PCI cards, you typically only need the alias lines to correlate the ethN interfaces with the appropriate
driver name, since the I/O base of a PCI card can be safely detected.
The available modules are typically stored in /lib/modules/`uname −r`/net where the uname −r
command gives the kernel version (e.g. 2.0.34). You can look in there to see which one matches your card.
Once you have the correct settings in your modules.conf file, you can test things out with:
modprobe eth0
modprobe eth1
...
modprobe ethN−1
where `N' is the number of ethernet interfaces you have. Note that the interface name (ethX) assigned to the
driver by the kernel is independent of the name used on the alias line. For further details on this, see: Using
the Ethernet Drivers as Modules
As of 2.2 and newer kernels, the boot probes have been sorted into safe and unsafe, so that all safe (e.g. PCI
and EISA) probes will find all related cards automatically. Systems with more than one ethernet card with at
least one of them being an ISA card will still need to do one of the following.)
There are two ways that you can enable auto−probing for the second (and third, and...) card. The easiest
method is to pass boot−time arguments to the kernel, which is usually done by LILO. Probing for the second
card can be achieved by using a boot−time argument as simple as ether=0,0,eth1. In this case eth0 and
eth1 will be assigned in the order that the cards are found at boot. Say if you want the card at 0x300 to be
eth0 and the card at 0x280 to be eth1 then you could use
The ether= command accepts more than the IRQ + I/O + name shown above. Please have a look at Passing
Ethernet Arguments... for the full syntax, card specific parameters, and LILO tips.
The second way (not recommended) is to edit the file Space.c and replace the 0xffe0 entry for the I/O
address with a zero. The 0xffe0 entry tells it not to probe for that device −− replacing it with a zero will
enable autoprobing for that device.
If you are using a compiled in driver, and have added an ether= to your LILO configuration file, note that it
won't take effect until you re−run lilo to process the updated configuration file.
Reason: The ne.c driver up to v2.0.30 only knows about the PCI ID number of RealTek 8029 based clone
cards. Since then, several others have also released PCI NE2000 clone cards, with different PCI ID numbers,
and hence the driver doesn't detect them.
Solution: The easiest solution is to upgrade to a v2.0.31 (or newer) version of the linux kernel. It knows the
ID numbers of about five different NE2000−PCI chips, and will detect them automatically at boot or at
module loading time. If you upgrade to 2.0.34 (or newer) there is a PCI−only specific NE2000 driver that is
slightly smaller and more efficient than the original ISA/PCI driver.
Problem: PCI NE2000 clone card is reported as an ne1000 (8 bit card!) at boot or when I load the ne.o
module for v2.0.x, and hence doesn't work.
Reason: Some PCI clones don't implement byte wide access (and hence are not truly 100% NE2000
compatible). This causes the probe to think they are NE1000 cards.
Solution: You need to upgrade to v2.0.31 (or newer) as described above. The driver(s) now check for this
hardware bug.
Problem: PCI NE2000 card gets terrible performance, even when reducing the window size as described in
the Performance Tips section.
Reason: The spec sheets for the original 8390 chip, desgined and sold over ten years ago, noted that a dummy
read from the chip was required before each write operation for maximum reliablity. The driver has the
facility to do this but it has been disabled by default since the v1.2 kernel days. One user has reported that
re−enabling this `mis−feature' helped their performance with a cheap PCI NE2000 clone card.
Solution: Since it has only been reported as a solution by one person, don't get your hopes up. Re−enabling
the read before write fix is done by simply editing the driver file in linux/drivers/net/,
uncommenting the line containing NE_RW_BUGFIX and then rebuilding the kernel or module as appropriate.
Please send an e−mail describing the performance difference and type of card/chip you have if this helps you.
(The same can be done for the ne2k−pci.c driver as well).
Problem: The ne2k−pci.c driver reports error messages like timeout waiting for Tx RDC with a
PCI NE2000 card and doesn't work right.
Reason: Your card and/or the card to PCI bus link can't handle the long word I/O optimization used in this
driver.
Solution: Firstly, check the settings available in the BIOS/CMOS setup to see if any related to PCI bus timing
are too aggressive for reliable operation. Otherwise using the ISA/PCI ne.c driver (or removing the
#define USE_LONGIO from ne2k−pci.c) should let you use the card.
Probem: ISA Plug and Play NE2000 (such as RealTek 8019) is not detected.
Reason: The original NE2000 specification (and hence the linux NE2000 driver in older kernels) did not have
support for Plug and Play.
Solution: Either use a 2.4 or newer kernel that has a NE2000 driver with PnP, or use the DOS configuration
disk that came with the card to disable PnP, and to set the card to a specified I/O address and IRQ. Add a line
to /etc/modules.conf like options ne io=0xNNN where 0xNNN is the hex I/O address you set the
card to. (This assumes you are using a modular driver; if not then use an ether=0,0xNNN,eth0 argument
at boot). You may also have to enter the BIOS/CMOS setup and mark the IRQ as Legacy−ISA instead of PnP.
Problem: NE*000 driver reports `not found (no reset ack)' during boot probe.
Reason: This is related to the above change. After the initial verification that an 8390 is at the probed I/O
address, the reset is performed. When the card has completed the reset, it is supposed to acknowedge that the
reset has completed. Your card doesn't, and so the driver assumes that no NE card is present.
Solution: You can tell the driver that you have a bad card by using an otherwise unused mem_end
hexidecimal value of 0xbad at boot time. You have to also supply a non−zero I/O base for the card when
using the 0xbad override. For example, a card that is at 0x340 that doesn't ack the reset would use
something like:
This will allow the card detection to continue, even if your card doesn't ACK the reset. If you are using the
driver as a module, then you can supply the option bad=0xbad just like you supply the I/O address.
Reason: This problem has been reported for kernels as old as 1.1.57 to the present. It appears confined to a
few software configurable clone cards. It appears that they expect to be initialized in some special way.
Solution: Several people have reported that running the supplied DOS software config program and/or the
supplied DOS driver prior to warm booting (i.e. loadlin or the `three−finger−salute') into linux allowed the
card to work. This would indicate that these cards need to be initialized in a particular fashion, slightly
Reason: Your NE2000 card is 0x20 wide in I/O space, which makes it hit the parallel port at 0x378. Other
devices that could be there are the second floppy controller (if equipped) at 0x370 and the secondary IDE
controller at 0x376−−0x377. If the port(s) are already registered by another driver, the kernel will not let
the probe happen.
Solution: Either move your card to an address like 0x280, 0x340, 0x320 or compile without parallel
printer support.
Reason: Same problem as above, but you have an older kernel that doesn't check for overlapping I/O regions.
Use the same fix as above, and get a new kernel while you are at it.
Problem: NE*000 ethercard probe at 0xNNN: 00 00 C5 ... not found. (invalid signature yy zz)
Reason: First off, do you have a NE1000 or NE2000 card at the addr. 0xNNN? And if so, does the hardware
address reported look like a valid one? If so, then you have a poor NE*000 clone. All NE*000 clones are
supposed to have the value 0x57 in bytes 14 and 15 of the SA PROM on the card. Yours doesn't −− it has `yy
zz' instead.
Solution: There are two ways to get around this. The easiest is to use an 0xbad mem_end value as described
above for the `no reset ack' problem. This will bypass the signature check, as long as a non−zero I/O base is
also given. This way no recompilation of the kernel is required.
The second method (for hackers) involves changing the driver itself, and then recompiling your kernel (or
module). The driver (/usr/src/linux/drivers/net/ne.c) has a "Hall of Shame" list at about line 42. This list is
used to detect poor clones. For example, the DFI cards use `DFI' in the first 3 bytes of the PROM, instead of
using 0x57 in bytes 14 and 15, like they are supposed to.
Problem: The machine hangs during boot right after the `8390...' or `WD....' message. Removing the NE2000
fixes the problem.
Solution: Change your NE2000 base address to something like 0x340. Alternatively, you can use the
``reserve='' boot argument in conjunction with the ``ether='' argument to protect the card from other device
driver probes.
Reason: Your NE2000 clone isn't a good enough clone. An active NE2000 is a bottomless pit that will trap
any driver autoprobing in its space. Changing the NE2000 to a less−popular address will move it out of the
way of other autoprobes, allowing your machine to boot.
Reason: It's the same problem as above, change the ethercard's address, or use the reserve/ether boot
arguments.
Reason: No, that's really during the silent SCSI probe, and it's the same problem as above.
Solution: There is no `magic solution' as there can be a number of reasons why it wasn't detected. The
following list should help you walk through the possible problems.
1) Build a new kernel with only the device drivers that you need. Verify that you are indeed booting the fresh
kernel. Forgetting to run lilo, etc. can result in booting the old one. (Look closely at the build time/date
reported at boot.) Sounds obvious, but we have all done it before. Make sure the driver is in fact included in
the new kernel, by checking the System.map file for names like ne_probe.
2) Look at the boot messages carefully. Does it ever even mention doing a ne2k probe such as `NE*000 probe
at 0xNNN: not found (blah blah)' or does it just fail silently. There is a big difference. Use dmesg|more to
review the boot messages after logging in, or hit Shift−PgUp to scroll the screen up after the boot has
completed and the login prompt appears.
3) After booting, do a cat /proc/ioports and verify that the full iospace that the card will require is
vacant. If you are at 0x300 then the ne2k driver will ask for 0x300−0x31f. If any other device driver has
registered even one port anywhere in that range, the probe will not take place at that address and will silently
continue to the next of the probed addresses. A common case is having the lp driver reserve 0x378 or the
second IDE channel reserve 0x376 which stops the ne driver from probing 0x360−0x380.
4) Same as above for cat /proc/interrupts. Make sure no other device has registered the interrupt
that you set the ethercard for. In this case, the probe will happen, and the ether driver will complain loudly at
boot about not being able to get the desired IRQ line.
5) If you are still stumped by the silent failure of the driver, then edit it and add some printk() to the probe.
For example, with the ne2k you could add/remove lines (marked with a `+' or `−') in
linux/drivers/net/ne.c like:
Then it will output messages for each port address that it checks, and you will see if your card's address is
being probed or not.
6) You can also get the ne2k diagnostic from Don's ftp site (mentioned in the howto as well) and see if it is
able to detect your card after you have booted into linux. Use the `−p 0xNNN' option to tell it where to look
for the card. (The default is 0x300 and it doesn't go looking elsewhere, unlike the boot−time probe.) The
output from when it finds a card will look something like:
NE2000 found at 0x300, using start page 0x40 and end page 0x80.
Your register values and PROM values will probably be different. Note that all the PROM values are doubled
for a 16 bit card, and that the ethernet address (00:00:c0:b0:05:65) appears in the first row, and the double
0x57 signature appears at the end of the PROM.
The output from when there is no card installed at 0x300 will look something like this:
The 0xff values arise because that is the value that is returned when one reads a vacant I/O port. If you
happen to have some other hardware in the region that is probed, you may see some non 0xff values as well.
7) Try warm booting into linux from a DOS boot floppy (via loadlin) after running the supplied DOS driver or
config program. It may be doing some extra (i.e. non−standard) "magic" to initialize the card.
8) Try Russ Nelson's ne2000.com packet driver to see if even it can see your card −− if not, then things do not
look good. Example:
The arguments are software interrupt vector, hardware IRQ, and I/O base. You can get it from any msdos
archive in pktdrv11.zip −− The current version may be newer than 11.
Solution: The most common reason for this is PCI machines that are not configured to map in ISA memory
devices. Hence you end up reading the PC's RAM (all 0xff values) instead of the RAM on the card that
contains the data from the received packet.
Other typical problems that are easy to fix are board conflicts, having cache or `shadow ROM' enabled for that
region, or running your ISA bus faster than 8Mhz. There are also a surprising number of memory failures on
ethernet cards, so run a diagnostic program if you have one for your ethercard.
Reason: Older versions of the Ultra driver only supported the card in the shared memory mode of operation.
Solution: The driver in kernel version 2.0 and above also supports the programmed I/O mode of operation.
Upgrade to v2.0 or newer.
Problem: Old wd8003 and/or jumper−settable wd8013 always get the IRQ wrong.
Reason: The old wd8003 cards and jumper−settable wd8013 clones don't have the EEPROM that the driver
can read the IRQ setting from. If the driver can't read the IRQ, then it tries to auto−IRQ to find out what it is.
And if auto−IRQ returns zero, then the driver just assigns IRQ 5 for an 8 bit card or IRQ 10 for a 16 bit card.
Solution: Avoid the auto−IRQ code, and tell the kernel what the IRQ that you have jumpered the card to in
your module configuration file (or via a boot time argument for in−kernel drivers).
Problem: SMC Ultra card is detected as wd8013, but the IRQ and shared memory base is wrong.
Reason: The Ultra card looks a lot like a wd8013, and if the Ultra driver is not present in the kernel, the wd
driver may mistake the ultra as a wd8013. The ultra probe comes before the wd probe, so this usually
shouldn't happen. The ultra stores the IRQ and mem base in the EEPROM differently than a wd8013, hence
the bogus values reported.
Solution: Recompile with only the drivers you need in the kernel. If you have a mix of wd and ultra cards in
one machine, and are using modules, then load the ultra module first.
Solution: The 3c503 driver probes for a free IRQ line in the order {5, 9/2, 3, 4}, and it should pick a line
which isn't being used. The driver chooses when the card is ifconfig'ed into operation.
If you are using a modular driver, you can use module parameters to set various things, including the IRQ
value.
The following selects IRQ9, base location 0x300, <ignored value>, and if_port #1 (the external transceiver).
Alternately, if the driver is compiled into the kernel, you can set the same values at boot by passing
parameters via LILO.
The following selects IRQ3, probes for the base location, <ignored value>, and the default if_port #0 (the
internal transceiver)
Reason: The 3c503 card can only use one of IRQ{5, 2/9, 3, 4} (These are the only lines that are connected to
the card.) If you pass in an IRQ value that is not in the above set, you will get the above message. Usually,
specifying an interrupt value for the 3c503 is not necessary. The 3c503 will autoIRQ when it gets ifconfig'ed,
and pick one of IRQ{5, 2/9, 3, 4}.
Solution: Use one of the valid IRQs listed above, or enable autoIRQ by not specifying the IRQ line at all.
Problem: The supplied 3c503 drivers don't use the AUI (thicknet) port. How does one choose it over the
default thinnet port?
Solution: The 3c503 AUI port can be selected at boot−time for in−kernel drivers, and at module insertion for
modular drivers. The selection is overloaded onto the low bit of the currently−unused dev−>rmem_start
variable, so a boot−time parameter of:
To specify the AUI port when loading as a module, just append xcvr=1 to the module options line along
with your I/O and IRQ values.
Note that you typically don't need DOS installed to run a DOS based configuration program. You can usually
just boot a DOS floppy disk and run them from the supplied floppy disk. You can also download OpenDOS
and FreeDOS for free.
If you require ISA−PnP enabled for compatibility with some other operating system then what you will have
to do depends on what kernel version you are using. For 2.2.x and older kernels, you will have to use the
isapnptools package with linux to configure the card(s) each time at boot. You will still have to make sure the
I/O address chosen for the card is probed by the driver or supplied as an io= option. For 2.4.x and newer
kernels, there is ISA−PnP support available built right into the kernel (if selected at build time) and if your
particular driver makes use of this support, then your card will be configured to an available I/O address and
IRQ all without any user supplied option values. You do not want to be trying to use the user−space
isapnptools and the in kernel ISA−PnP support at the same time.
Some systems have an `enable PnP OS' (or similar named) option in the BIOS/CMOS setup menu which does
not really have anything to do with ISA−PnP hardware. See below for more details on this option.
PCI machine detects card but driver fails probe (PnP OS).
Some PCI BIOSes may not enable all PCI cards at power−up, especially if the BIOS option `PnP OS' is
enabled. This mis−feature is to support the current release of Windows which still uses some real−mode
drivers. Either disable this option, or try and upgrade to a newer driver which has the code to enable a disabled
card.
Note that kernel version 2.4.x has better support to deal with this option − in particular you should be able to
enable this option, and the kernel/drivers should be able to set up and/or enable the cards on its own.
If you are using a modular based kernel, such as those installed by most of the linux distributions, then try and
use the configuration utility for the distribution to select the module for your card. For ISA cards, it is a good
idea to determine the I/O address of the card and add it as an option (e.g. io=0x340) if the configuration
utility asks for any options. If there is no configuration utility, then you will have to add the correct module
name (and options) to /etc/modules.conf −− see man modprobe for more details.
The next main cause is having another device using part of the I/O space that your card needs. Most cards are
16 or 32 bytes wide in I/O space. If your card is set at 0x300 and 32 bytes wide, then the driver will ask for
0x300−0x31f. If any other device driver has registered even one port anywhere in that range, the probe will
not take place at that address and the driver will silently continue to the next of the probed addresses. So, after
booting, do a cat /proc/ioports and verify that the full I/O space that the card will require is vacant.
Another problem is having your card jumpered to an I/O address that isn't probed by default. The list of
probed addresses for each driver is easily found just after the text comments in the driver source. Even if the
I/O setting of your card is not in the list of probed addresses, you can supply it at boot (for in−kernel drivers)
with the ether= command as described in Passing Ethernet Arguments... Modular drivers can make use of
the io= option in /etc/modules.conf to specify an address that isn't probed by default.
PCI machine detects card but driver fails probe (PnP OS). 18
Linux Ethernet−Howto
You have to make sure that the 8390.o module gets loaded before loading the second half of the driver so
that the second half of the driver can find the functions in 8390.o that it needs.
Possible causes: (1)Forgetting to run depmod after installing a new kernel and modules, so that module
dependencies like this are handled automatically. (2)Using insmod instead of modprobe, as insmod doesn't
check for any module ordering constraints. (3)The module 8390.o is not in the directory beside the other
half of the driver where it should be.
Werner says that the driver for the ENI155p is rather stable, while the driver for the ZN1221 is presently
unfinished.
Yes, there are currently several. One of the prominent Linux network developers rated the performance of the
cards with linux drivers as follows: 1) Intel E1000, 2) Tigon2/Acenic, 3) SysKonnect sk−98xx, 4)
Tigon3/bcm57xx. This was as of March 2002 and subject to change of course.
FDDI Support
Is there FDDI support for Linux?
Yes. Larry Stefani has written a driver for v2.0 with Digital's DEFEA (FDDI EISA) and DEFPA (FDDI PCI)
cards. This was included into the v2.0.24 kernel. Currently no other cards are supported though.
Cameron Spitzer writes the following about full duplex 10Base−T cards: ``If you connect it to a full duplex
switched hub, and your system is fast enough and not doing much else, it can keep the link busy in both
directions. There is no such thing as full duplex 10BASE−2 or 10BASE−5 (thin and thick coax). Full Duplex
works by disabling collision detection in the adapter. That's why you can't do it with coax; the LAN won't run
that way. 10BASE−T (RJ45 interface) uses separate wires for send and receive, so it's possible to run both
ways at the same time. The switching hub takes care of the collision problem. The signalling rate is 10 Mbps.''
So as you can see, you still will only be able to receive or transmit at 10Mbps, and hence don't expect a 2x
performance increase. As to whether it is supported or not, that depends on the card and possibly the driver.
Some cards may do auto−negotiation, some may need driver support, and some may need the user to select an
option in a card's EEPROM configuration. Only the serious/heavy user would notice the difference between
the two modes anyway.
In v2.0 kernels, only one processor was allowed `in kernel' (i.e. changing kernel data and/or running device
drivers) at any given time. So from the point of view of the card (and the associated driver) nothing was
different from uni processor (UP) operation and things just continued to work. (This was the easiest way to
get a working MP version of Linux − one big lock around the whole kernel only allows one processor in at a
time. This way you know that you won't have two processors trying to change the same thing at the same
time!)
The downside to only allowing one processor in the kernel at a time was that you only got MP performance if
the running programs were self contained and calculation intensive. If the programs did a lot of input/output
(I/O) such as reading or writing data to disk or over a network, then all but one of the processors would be
stalled waiting on their I/O requests to be completed while the one processor running in kernel frantically tries
to run all the device drivers to fill the I/O requests. The kernel becomes the bottleneck and since there is only
one processor running in the kernel, the performance of a MP machine in the heavy I/O, single−lock case
quickly degrades close to that of a single processor machine.
Since this is clearly less than ideal (esp. for file/WWW servers, routers, etc.) the v2.2 kernels have finer
grained locking − meaning that more than one processor can be in the kernel at a time. Instead of one big lock
around the whole kernel, there are a lot of smaller locks protecting critical data from being manipulated by
more than one processor at a time − e.g. one processor can be running the driver for the network card, while
another processor is running the driver for the disk drive at the same time.
Okay, with that all in mind here are the snags: The finer locking means that you can have one processor trying
to send data out through an ethernet driver while another processor tries to access the same driver/card to do
something else (such as get the card statistics for cat /proc/net/dev). Oops − your card stats just got
sent out over the wire, while you got data for your stats instead. Yes, the card got confused by being asked to
do two (or more!) things at once, and chances are it crashed your machine in the process.
So, the driver that worked for UP is no longer good enough − it needs to be updated with locks that control
access to the underlying card so that the three tasks of receive, transmit and manipulation of configuration
data are serialized to the degree required by the card for stable operation. The scary part here is that a driver
not yet updated with locks for stable MP operation will probably appear to be working in a MP machine under
light network load, but will crash the machine or at least exhibit strange behaviour when two (or more!)
processors try to do more than one of these three tasks at the same time.
The updated MP aware ethernet driver will (at a minimum) require a lock around the driver that limits access
at the entry points from the kernel into the driver to `one at a time please'. With this in place, things will be
serialized so that the underlying hardware should be treated just as if it was being used in a UP machine, and
so it should be stable. The downside is that the one lock around the whole ethernet driver has the same
negative performance implications that having one big lock around the whole kernel had (but on a smaller
scale) − i.e. you can only have one processor dealing with the card at a time. [Technical Note: The
performance impact may also include increased interrupt latencies if the locks that need to be added are of the
irqsave type and they are held for a long time.]
Possible improvements on this situation can be made in two ways. You can try to minimize the time between
when the lock is taken and when it is released, and/or you can implement finer grained locking within the
driver (e.g. a lock around the whole driver would be overkill if a lock or two protecting against simultaneous
access to a couple of sensitive registers/settings on the card would suffice).
However, for older non−intelligent cards that were never designed with MP use in mind, neither of these
improvements may be feasible. Worse yet is that the non−intelligent cards typically require the processor to
move the data between the card and the computer memory, so in a worst case scenario the lock will be held
the whole time that it takes to move each 1.5kB data packet over an ISA bus.
Note that the changes that are required to make a driver architecture independent aren't that complicated. You
only need to do the following:
−multiply all jiffies related values by HZ/100 to account for the different HZ value that the Alpha uses.
(i.e timeout=2; becomes timeout=2*HZ/100;)
−replace any I/O memory (640k to 1MB) pointer dereferences with the appropriate readb() writeb() readl()
writel() calls, as shown in this example.
−replace all memcpy() calls that have I/O memory as source or target destinations with the appropriate one of
memcpy_fromio() or memcpy_toio().
Details on handling memory accesses in an architecture independent fashion are documented in the file
linux/Documentation/IO−mapping.txt that comes with recent kernels.
Linux Sparc
Note that some Sparc ethernet hardware gets its MAC address from the host computer, and hence you can end
up with multiple interfaces all with the same MAC address. If you need to put more than one interface on the
same net then use the hw option to ifconfig to assign unique MAC address.
Issues regarding porting PCI drivers to the Sparc platform are similar to those mentioned above for the AXP
platform. In addition there may be some endian issues, as the Sparc is big endian, and the AXP and ix86 are
little endian.
supported. (Links to such sites are welcome here − send them in!)
You can link 2 machines, but no more than that, without extra devices/gizmos, by using a crossover cable.
Some newer fancy autonegotiaton cards may not work on a crossover cable though. And no, you can't hack
together a hub just by crossing a few wires and stuff. It's pretty much impossible to do the collision signal
right without duplicating a hub.
Your ethernet device was not detected at boot/module insertion time, and when ifconfig and route are
run, they have no device to work with. Use dmesg | more to review the boot messages and see if there are
any messages about detecting an ethernet card.
Some other device has taken the IRQ that your ethercard is trying to use, and so the ethercard can't use the
IRQ. You don't necessairly need to reboot to resolve this, as some devices only grab the IRQs when they need
them and then release them when they are done. Examples are some sound cards, serial ports, floppy disk
driver, etc. You can type cat /proc/interrupts to see which interrupts are presently in use. Most of
the Linux ethercard drivers only grab the IRQ when they are opened for use via `ifconfig'. If you can get the
other device to `let go' of the required IRQ line, then you should be able to `Try again' with ifconfig.
This is because people are running a newer version of the `ifconfig' program than their kernel version. This
new version of ifconfig is not able to report these properties when used in conjunction with an older kernel.
You can either upgrade your kernel, `downgrade' ifconfig, or simply ignore it. The kernel knows your
hardware address, so it really doesn't matter if ifconfig can't read it.
You may also get strange information if the ifconfig program you are using is a lot older than the kernel
you are using.
Look again. It says RX packets big number PAUSE errors 0 PAUSE dropped 0 PAUSE
overrun 0. And the same for the TX column. Hence the big numbers you are seeing are the total number of
packets that your machine has rec'd and transmitted. If you still find it confusing, try typing cat
/proc/net/dev instead.
Contrary to what you have heard, the files in /dev/* are not used. You can delete any /dev/wd0,
/dev/ne0 and similar entries.
int s=socket(AF_INET,SOCK_PACKET,htons(ETH_P_ALL));
This gives you a socket receiving every protocol type. Do recvfrom() calls to it and it will fill the
sockaddr with device type in sa_family and the device name in the sa_data array. I don't know who originally
invented SOCK_PACKET for Linux (its been in for ages) but its superb stuff. You can use it to send stuff raw
too via sendto() calls. You have to have root access to do either of course.
3. Performance Tips
Here are some tips that you can use if you are suffering from low ethernet throughput, or to gain a bit more
speed on those ftp transfers.
The ttcp.c program is a good test for measuring raw throughput speed. Another common trick is to do a
ftp> get large_file /dev/null where large_file is > 1MB and residing in the buffer cache
on the Tx'ing machine. (Do the `get' at least twice, as the first time will be priming the buffer cache on the
Tx'ing machine.) You want the file in the buffer cache because you are not interested in combining the file
access speed from the disk into your measurement. Which is also why you send the incoming data to
/dev/null instead of onto the disk.
In this case the card either drops the new packet, or writes over top of a previously received packet. Either one
seriously interrupts the smooth flow of traffic by causing/requesting re−transmissions and can seriously
degrade performance by up to a factor of 5!
Cards with more onboard memory are able to ``buffer'' more packets, and thus can handle larger bursts of
back−to−back packets without dropping packets. This in turn means that the card does not require as low a
latency from the the host computer with respect to pulling the packets out of the buffer to avoid dropping
Most 8 bit cards have an 8kB buffer, and most 16 bit cards have a 16kB buffer. Most Linux drivers will
reserve 3kB of that buffer (for two Tx buffers), leaving only 5kB of receive space for an 8 bit card. This is
room enough for only three full sized (1500 bytes) ethernet packets.
The recommended ISA bus clock is about 8MHz, but many motherboards and peripheral devices can be run at
higher frequencies. The clock frequency for the ISA bus can usually be set in the CMOS setup, by selecting a
divisor of the mainboard/CPU clock frequency. Some ISA and PCI/ISA mainboards may not have this option,
and so you are stuck with the factory default.
For example, here are some receive speeds as measured by the TTCP program on a 40MHz 486, with an 8 bit
WD8003EP card, for different ISA bus speeds.
You would be hard pressed to do better than 1075kB/s with any 10Mb/s ethernet card, using TCP/IP.
However, don't expect every system to work at fast ISA bus speeds. Most systems will not function properly
at speeds above 13MHz. (Also, some PCI systems have the ISA bus speed fixed at 8MHz, so that the end user
does not have the option of increasing it.)
In addition to faster transfer speeds, one will usually also benefit from a reduction in CPU usage due to the
shorter duration memory and I/O cycles. (Note that hard disks and video cards located on the ISA bus will
also usually experience a performance increase from an increased ISA bus speed.)
Be sure to back up your data prior to experimenting with ISA bus speeds in excess of 8MHz, and thouroughly
test that all ISA peripherals are operating properly after making any speed increases.
Recent versions of the route command have the ability to set the size of this window on the fly. Usually it is
only for the local net that this window must be reduced, as computers that are behind a couple of routers or
gateways are `buffered' enough to not pose a problem. An example usage would be:
where win_size is the size of the window you wish to use (in bytes). An 8 bit 3c503 card on an ISA bus
operating at a speed of 8MHz or less would work well with a window size of about 4kB. Too large a window
will cause overruns and dropped packets, and a drastic reduction in ethernet throughput. You can check the
operating status by doing a cat /proc/net/dev which will display any dropped or overrun conditions
that occurred.
The possible reason for this could be due to the difference in on board buffer size between the 8 bit and the 16
bit cards. The maximum ethernet packet size is about 1500 bytes. Now that 8kB NFS packet will arrive as
about 6 back to back maximum size ethernet packets. Both the 8 and 16 bit cards have no problem Rx'ing
back to back packets. The problem arises when the machine doesn't remove the packets from the cards buffer
in time, and the buffer overflows. The fact that 8 bit cards take an extra ISA bus cycle per transfer doesn't help
either. What you can do if you have an 8 bit card is either set the NFS transfer size to 2kB (or even 1kB), or
try increasing the ISA bus speed in order to get the card's buffer cleared out faster. I have found that an old
WD8003E card at 8MHz (with no other system load) can keep up with a large receive at 2kB NFS size, but
not at 4kB, where performance was degraded by a factor of three.
On the other hand, if the default mount option is to use 1kB size and you have at least a 16 bit ISA card, you
may find a significant increase in going to 4kB (or even 8kB).
Supported means that a driver for that card exists, and many people are happily using it and it seems quite
reliable.
Semi−Supported means that a driver exists, but at least one of the following descriptions is true: (1) The
driver and/or hardware are buggy, which may cause poor performance, failing connections or even crashes.
(2) The driver is new or the card is fairly uncommon, and hence the driver has seen very little use/testing and
the driver author has had very little feedback. Obviously (2) is preferable to (1), and the individual description
of the card/driver should make it clear which one holds true. In either case, you will probably have to answer
`Y' when asked ``Prompt for development and/or incomplete code/drivers?'' when running make config.
Obsolete means that a driver exists, and was probably at one time considered Semi−Supported. However, due
to lack of interest, users, and support, it is known to not work anymore. The driver is still in the kernel, but
disabled in the configuration option menu. The general plan is that if it does not get updated by the next kernel
development cycle, it will be dropped entirely. Usually a driver marked obsolete simply needs an update to
match changes in the kernel to driver interface, or other similar kernel API changes.
Dropped means that the driver was once obsolete (see above) and since there was not enough interest in fixing
it, it has been removed from the current kernel tree. There is nothing stopping anyone from copying the driver
from an older kernel, making the required updates and using it.
Not Supported means there is not a driver currently available for that card. This could be due to a lack of
interest in hardware that is rare/uncommon, or because the vendors won't release the hardware documentation
required to write a driver.
Note that the difference between `Supported' and `Semi−Supported' is rather subjective, and is based on user
feedback. So be warned that you may find a card listed as semi−supported works perfectly for you (which is
great), or that a card listed as supported gives you no end of troubles and problems (which is not so great).
After the status, the name of the driver given in the linux kernel is listed. This will also be the name of the
driver module that would be used in the alias eth0 driver_name line that is found in the
/etc/modules.conf module configuration file.
4.1 3Com
If you are not sure what your card is, but you think it is a 3Com card, you can probably figure it out from the
assembly number. 3Com has a document `Identifying 3Com Adapters By Assembly Number' (ref 24500002)
that would most likely clear things up. Also check out their WWW/FTP site with various goodies:
www.3Com.com that you may find useful (including PDFs with technical info for their cards).
3c501
Status: Semi−Supported, Driver Name: 3c501
This obsolete stone−age 8 bit card is really too brain−damaged to use. Avoid it like the plague. Do not
purchase this card, even as a joke. It's performance is horrible, and it breaks in many ways.
For those not yet convinced, the 3c501 can only do one thing at a time −− while you are removing one packet
from the single−packet buffer it cannot receive another packet, nor can it receive a packet while loading a
transmit packet. This was fine for a network between two 8088−based computers where processing each
packet and replying took 10's of msecs, but modern networks send back−to−back packets for almost every
transaction.
AutoIRQ works, DMA isn't used, the autoprobe only looks at 0x280 and 0x300, and the debug level is set
with the third boot−time argument.
Once again, the use of a 3c501 is strongly discouraged! Even more so with a IP multicast kernel, as you will
grind to a halt while listening to all multicast packets. See the comments at the top of the source code for
more details.
The 3c503 does not have ``EEPROM setup'', so a diagnostic/setup program isn't needed before running the
card with Linux. The shared memory address of the 3c503 is set using jumpers that are shared with the boot
PROM address. This is confusing to people familiar with other ISA cards, where you always leave the jumper
set to ``disable'' unless you have a boot PROM.
4.1 3Com 27
Linux Ethernet−Howto
These cards should be about the same speed as the same bus width WD80x3, but turn out to be actually a bit
slower. These shared−memory ethercards also have a programmed I/O mode that doesn't use the 8390
facilities (their engineers found too many bugs!) The Linux 3c503 driver can also work with the 3c503 in
programmed−I/O mode, but this is slower and less reliable than shared memory mode. Also, programmed−I/O
mode is not as well tested when updating the drivers. You shouldn't use the programmed−I/O mode unless
you need it for compatibility with another operating system that is used on the same computer.
The 3c503's IRQ line is set in software, with no hints from an EEPROM. Unlike the MS−DOS drivers, the
Linux driver has capability to autoIRQ: it uses the first available IRQ line in {5,2/9,3,4}, selected each time
the card is ifconfig'ed. Note that `ifconfig' will return EAGAIN if no IRQ line is available at that time.
Some common problems that people have with the 503 are discussed in Problems with....
If you intend on using this driver as a loadable module you should probably see Using the Ethernet Drivers as
Modules for module specific information.
These cards use the i82586 chip but are not that many of them about. It is included in the standard kernel, but
it is classed as an alpha driver. See Alpha Drivers for important information on using alpha−test ethernet
drivers with Linux.
There is also the file /usr/src/linux/drivers/net/README.3c505 that you should read if you
are going to use one of these cards. It contains various options that you can enable/disable.
Etherlink−16 3c507
Status: Semi−Supported, Driver Name: 3c507
This card uses one of the Intel chips, and the development of the driver is closely related to the development
of the Intel Ether Express driver. The driver is included in the standard kernel release, but as an alpha driver.
See Alpha Drivers for important information on using alpha−test ethernet drivers with Linux.
This card was fairly inexpensive and had good performance for an ISA non−bus−master design. The
drawbacks were that the original 3c509 required very low interrupt latency. The 3c509B shouldn't suffer from
the same problem, due to having a larger buffer. (See below.) These cards use PIO transfers, similar to a
ne2000 card, and so a shared memory card such as a wd8013 will be more efficient in comparison.
The original 3c509 had a small packet buffer (4kB total, 2kB Rx, 2kB Tx), causing the driver to occasionally
drop a packet if interrupts were masked for too long. To minimize this problem, you can try unmasking
interrupts during IDE disk transfers (see man hdparm) and/or increasing your ISA bus speed so IDE
transfers finish sooner.
3c509B users should use either the supplied DOS utility to disable the plug and play support, and to set the
output media to what they require. The linux driver currently does not support the Autodetect media setting,
so you have to select 10Base−T or 10Base−2 or AUI. Note that if you turn off PnP entirely, you should exit
the utility and and then follow that with a hard reset to ensure that the new settings take effect.
Some people ask about the ``Server or Workstation'' and ``Highest Modem Speed'' settings presented in the
DOS configuration utility. These settings don't actually change any hardware settings, rather they are only
tuning hints to the DOS driver. The linux driver does not need or use these hints. Also, DON'T enable EISA
mode on this ISA card unless you really have an EISA machine, or you may end up needing to find an EISA
machine just to get your ISA card back into ISA mode!
The card with the lowest hardware ethernet address will always end up being eth0 in a multiple ISA 3c509
configuration. This shouldn't matter to anyone, except for those people who want to assign a 6 byte hardware
address to a particular interface. If this really bothers you, have a look at Donald's latest driver, as you may be
able to use a 0x3c509 value in the unused mem address fields to order the detection to suit your needs.
3c515
Status: Supported, Driver Name: 3c515
This is 3Com's ISA 100Mbps offering, codenamed ``CorkScrew''. Note that you will never achieve full
100Mbps on an ISA bus.
3c523
Status: Semi−Supported, Driver Name: 3c523
This MCA bus card uses the i82586, and Chris Beauregard has modified the ni52 driver to work with these
cards.
Yes, another i82586 MCA card. No, not too much interest in it. Better chances with the 3c529 if you are stuck
with MCA, since it uses the tried and true 3c509 core.
3c529
Status: Supported, Driver Name: 3c509
This card actually uses the same chipset as the 3c509. People have actually been using this card in MCA
machines.
3c515 29
Linux Ethernet−Howto
http://www.linuxtr.net/download.html
3c556
Status: Supported, Driver Name: 3c59x
A mini PCI NIC found on various IBM and HP notebooks. Also knownas a `laptop tornado'.
3c562
Status: Supported, Driver Name: 3c589_cs
This PCMCIA card is the combination of a 3c589B ethernet card with a modem. The modem appears as a
standard modem to the end user. The only difficulty is getting the two separate linux drivers to share one
interrupt. There are a couple of new registers and some hardware interrupt sharing support. Thanks again to
Cameron for getting a sample unit and documentation sent off to David Hinds.
3c575
Status: Supported, Driver Name: 3c59x
Note that to support this Cardbus device in old 2.2 kernels, you had to use 3c575_cb.c from the pcmcia_cs
package.
3c579
Status: Supported, Driver Name: 3c509
The EISA version of the 509. The current EISA version uses the same 16 bit wide chip rather than a 32 bit
interface, so the performance increase isn't stunning. Make sure the card is configured for EISA addressing
mode. Read the above 3c509 section for info on the driver.
3c589 / 3c589B
Status: Semi−Supported, Driver Name: 3c589_cs
Many people have been using this PCMCIA card for quite some time now. The "B" in the name means the
same here as it does for the 3c509 case.
3c590 / 3c595
Status: Supported, Driver Name: 3c59x
These ``Vortex'' cards are for PCI bus machines, with the '590 being 10Mbps and the '595 being 3Com's
100Mbs offering. Also note that you can run the '595 as a '590 (i.e. in a 10Mbps mode). The 3c59x line was
replaced by the 3c9xx line quite some time ago, and so these cards are considered rather old.
Note that there are two different 3c590 cards out there, early models that had 32kB of on−board memory, and
later models that only have 8kB of memory. The 3c595 cards have 64kB, as you can't get away with only 8kB
RAM at 100Mbps!
3c592 / 3c597
Status: Supported, Driver Name: 3c59x
These are the EISA versions of the 3c59x series of cards. The 3c592/3c597 (aka Demon) should work with
the vortex driver discussed above.
These cards (aka `Boomerang', aka EtherLink III XL) have been released to take over the place of the
3c590/3c595 cards, with some additional support added to the vortex/3c59x driver. The driver found in older
kernels may not support the latest revision(s) of these cards, so you may need a driver update.
Note that the 3c905C has support for TCP/UDP/IP checksumming in hardware support − meaning less work
for the computer CPU to do!
This driver supports several other Gigabit cards in addition to the 3Com model.
This driver supports several other Gigabit cards in addition to the 3Com model. The tg3 driver is a complete
rewrite by several linux developers in an effort to improve on the vendor supplied bcm5700 driver.
4.2 Accton
Accton MPX
Status: Supported, Driver Name: ne (+8390)
Don't let the name fool you. This is still supposed to be a NE2000 compatible card, and should work with the
ne2000 driver.
3c592 / 3c597 31
Linux Ethernet−Howto
Apparently there have been several revisions of the EN1207 (A through D) with A, B, and C being tulip based
and the D revision being RealTek 8139 based (different driver). So as with all purchases, you should try and
make sure you can return it if it doesn't work for you.
A driver for these parallel port adapters was available around the time of the 2.0 or 2.1 kernel. It's last known
location was:
http://www.unix−ag.uni−siegen.de/~nils/accton_linux.html
4.3 Adaptec
Note that some of the older Adaptec 32 bit boards used a tulip clone.
These are a series of low−cost ethercards using the 79C960 version of the AMD LANCE. These are
bus−master cards, and hence one of the faster ISA bus ethercards available.
DMA selection and chip numbering information can be found in AMD LANCE.
AT1700
Status: Supported, Driver Name: at1700
Note that to access this driver during make config you still have to answer `Y' when asked ``Prompt for
development and/or incomplete code/drivers?'' at the first. This is simply due to lack of feedback on the driver
stability due to it being a relatively rare card. If you have problems with the driver that ships with the kernel
then you may be interested in the alternative driver available at:
http://www.cc.hit−u.ac.jp/nagoya/at1700/
The Allied Telesis AT1700 series ethercards are based on the Fujitsu MB86965. This chip uses a programmed
I/O interface, and a pair of fixed−size transmit buffers. This allows small groups of packets to be sent
back−to−back, with a short pause while switching buffers.
The Fujitsu chip used on the AT1700 has a design flaw: it can only be fully reset by doing a power cycle of
the machine. Pressing the reset button doesn't reset the bus interface. This wouldn't be so bad, except that it
can only be reliably detected when it has been freshly reset. The solution/work−around is to power−cycle the
machine if the kernel has a problem detecting the AT1700.
AT2400
Status: Supported, Driver Name: ne, ne2k−pci (+8390)
Yet another PCI NE2000 clone card. This one is based on the RealTek 8029 chip.
AT2450
Status: Supported, Driver Name: pcnet32
This is the PCI version of the AT1500, and it doesn't suffer from the problems that the Boca 79c970 PCI card
does. DMA selection and chip numbering information can be found in AMD LANCE.
AT2500
Status: Supported, Driver Name: 8139too, rtl8139(old)
This card uses the RealTek 8139 chip − see the section RealTek 8139.
AT2540FX
Status: Semi−Supported, Driver Name: eepro100
This card uses the i82557 chip, and hence may/should work with the eepro100 driver. If you try this please
send in a report so this information can be updated.
There really is no AMD ethernet card. You are probably reading this because the only markings you could
find on your card said AMD and the above number. The 7990 is the original `LANCE' chip, but most stuff
(including this document) refer to all these similar chips as `LANCE' chips. (...incorrectly, I might add.)
AT2400 33
Linux Ethernet−Howto
These above numbers refer to chips from AMD that are the heart of many ethernet cards. For example, the
Allied Telesis AT1500 (see AT1500) and the NE1500/2100 (see NE1500) use these chips.
The 7990/79c90 have long been replaced by newer versions. The 79C960 (a.k.a. PCnet−ISA) essentially
contains the 79c90 core, along with all the other hardware support required, which allows a single−chip
ethernet solution. The 79c961 (PCnet−ISA+) is a jumperless Plug and Play version of the '960. The final chip
in the ISA series is the 79c961A (PCnet−ISA II), which adds full duplex capabilities. All cards with one of
these chips should work with the lance.c driver, with the exception of very old cards that used the original
7990 in a shared memory configuration. These old cards can be spotted by the lack of jumpers for a DMA
channel.
One common problem people have is the `busmaster arbitration failure' message. This is printed out when the
LANCE driver can't get access to the bus after a reasonable amount of time has elapsed (50us). This usually
indicates that the motherboard implementation of bus−mastering DMA is broken, or some other device is
hogging the bus, or there is a DMA channel conflict. If your BIOS setup has the `GAT option' (for Guaranteed
Access Time) then try toggling/altering that setting to see if it helps.
Also note that the driver only looks at the addresses: 0x300, 0x320, 0x340, 0x360 for a valid card,
and any address supplied by an ether= boot argument is silently ignored (this will be fixed) so make sure
your card is configured for one of the above I/O addresses for now.
The driver will still work fine, even if more than 16MB of memory is installed, since low−memory
`bounce−buffers' are used when needed (i.e. any data from above 16MB is copied into a buffer below 16MB
before being given to the card to transmit.)
The DMA channel can be set with the low bits of the otherwise−unused dev−>mem_start value (a.k.a.
PARAM_1). (see PARAM_1) If unset it is probed for by enabling each free DMA channel in turn and
checking if initialization succeeds.
The HP−J2405A board is an exception: with this board it's easy to read the EEPROM−set values for the IRQ,
and DMA.
The sis900.txt file in 2.4 kernels states that "AM79C901 HomePNA PHY is not thoroughly tested, there
may be some bugs in the "on the fly" change of transceiver." so you may want to check that if using a newer
kernel.
This is the PCnet−32 −− a 32 bit bus−master version of the original LANCE chip for VL−bus and local bus
systems. chip. While these chips can be operated with the standard lance.c driver, a 32 bit version
(pcnet32.c) is also available that does not have to concern itself with any 16MB limitations associated
with the ISA bus.
This is the PCnet−PCI −− similar to the PCnet−32, but designed for PCI bus based systems. Please see the
above PCnet−32 information. This means that you need to build a kernel with PCI BIOS support enabled. The
'970A adds full duplex support along with some other features to the original '970 design.
Note that the Boca implementation of the 79C970 fails on fast Pentium machines. This is a hardware problem,
as it affects DOS users as well. See the Boca section for more details.
This is AMD's 100Mbit chip for PCI systems, which also supports full duplex operation. It was introduced in
June 1996.
This is the PCnet−SCSI −− which is basically treated like a '970 from an Ethernet point of view. Also see the
above information. Don't ask how well the SCSI half of the chip is supported −− this is the Ethernet−HowTo,
not the SCSI−HowTo.
This EISA bus card is based on the common 8390 chip used in the ne2000 and wd80x3 cards. Note that to
access this driver during make config you still have to answer `Y' when asked ``Prompt for development
and/or incomplete code/drivers?'' at the first. This is simply due to lack of feedback on the driver stability due
to it being a relatively rare card. Feedback has been low even though the driver has been in the kernel since
v1.1.25.
4.7 Apricot
This on board ethernet uses an i82596 bus−master chip. It can only be at I/O address 0x300. By looking at
the driver source, it appears that the IRQ is also hardwired to 10.
Earlier versions of the driver had a tendency to think that anything living at 0x300 was an apricot NIC. Since
then the hardware address is checked to avoid these false detections.
4.8 Arcnet
Status: Supported, Driver Name: arcnet (arc−rimi, com90xx, com20020)
With the very low cost and better performance of ethernet, chances are that most places will be giving away
their Arcnet hardware for free, resulting in a lot of home systems with Arcnet.
An advantage of Arcnet is that all of the cards have identical interfaces, so one driver will work for everyone.
It also has built in error handling so that it supposedly never loses a packet. (Great for UDP traffic!) Note that
the arcnet driver uses `arc0' as its name instead of the usual `eth0' for ethernet devices.
There are information files contained in the standard kernel for setting jumpers, general hints and where to
mail bug reports.
Supposedly the driver also works with the 100Mbs ARCnet cards as well!
Boca BEN400
Status: Supported, Driver Name: ne (+8390)
These cards are based on AMD's PCnet chips. Many people reported endless problems with these VLB/PCI
cards. The problem was supposedly due to Boca not installing some capacitors that AMD recommended. (The
older ISA cards don't appear to suffer the same problems.) Boca was offering a `warranty repair' for affected
owners, which involved adding one of the missing capacitors, but it appears that this fix didn't work 100
percent for most people, although it helped some. The cards are so old now that it wouldn't be worth pursuing.
More general information on the AMD chips can be found in AMD LANCE.
4.10 Broadcom
Broadcom Tigon2
Status: Supported, Driver Name: acenic
Broadcom Tigon3
Status: Supported, Driver Name: tg3
4.11 Cabletron
Lack of programming information from Cabletron at the time drivers were being developed for these cards
meant that the drivers were not supported as well as they could have been.
Apparently Cabletron has since changed their policy with respect to programming information (like Xircom).
However, at this point in time, there is little demand for modified/updated drivers for the old E20xx and
E21xx cards.
These are NEx000 almost−clones that are reported to work with the standard NEx000 drivers, thanks to a
ctron−specific check during the probe.
E2100
Status: Semi−Supported, Driver Name: e2100 (+8390)
The E2100 is a poor design. Whenever it maps its shared memory in during a packet transfer, it maps it into
the whole 128K region! That means you can't safely use another interrupt−driven shared memory device in
that region, including another E2100. It will work most of the time, but every once in a while it will bite you.
(Yes, this problem can be avoided by turning off interrupts while transferring packets, but that will almost
certainly lose clock ticks.) Also, if you mis−program the board, or halt the machine at just the wrong moment,
even the reset button won't bring it back. You will have to turn it off and leave it off for about 30 seconds.
Media selection is automatic, but you can override this with the low bits of the dev−>mem_end parameter.
See PARAM_2. Module users can specify an xcvr=N value as an option in the /etc/modules.conf
file.
Also, don't confuse the E2100 for a NE2100 clone. The E2100 is a shared memory NatSemi DP8390 design,
roughly similar to a brain−damaged WD8013, whereas the NE2100 (and NE1500) use a bus−mastering AMD
LANCE design.
If you intend on using this driver as a loadable module you should probably see Using the Ethernet Drivers as
Modules for module specific information.
4.10 Broadcom 37
Linux Ethernet−Howto
E22**
Status: Semi−Supported, Driver Name: lance
According to information in a Cabletron Tech Bulletin, these cards use the standard AMD PC−Net chipset
(see AMD PC−Net) and should work with the generic lance driver.
4.12 Cogent
EM100−ISA/EISA
Status: Semi−Supported, Driver Name: smc9194
These cards use the SMC 91c100 chip and may work with the SMC 91c92 driver, but this has yet to be
verified.
These are yet another DEC 21040 implementation that should hopefully work fine with the standard 21040
driver.
The EM400 and the EM964 are four port cards using a DEC 21050 bridge and 4 21040 chips.
See DEC 21040 for more information on these cards, and the present driver situation.
4.13 Compaq
Compaq aren't really in the business of making ethernet cards, but a lot of their systems have embedded
ethernet controllers on the motherboard.
Machines such as the XL series have an AMD 79c97x PCI chip on the mainboard that can be used with the
standard LANCE driver. But before you can use it, you have to do some trickery to get the PCI BIOS to a
place where Linux can see it. Frank Maas was kind enough to provide the details:
`` The problem with this Compaq machine however is that the PCI directory is loaded in high memory, at a
spot where the Linux kernel can't (won't) reach. Result: the card is never detected nor is it usable (sideline: the
mouse won't work either) The workaround (as described thoroughly in http://www−c724.uibk.ac.at/XL/) is to
load MS−DOS, launch a little driver Compaq wrote and then load the Linux kernel using LOADLIN. Ok, I'll
give you time to say `yuck, yuck', but for now this is the only working solution I know of. The little driver
simply moves the PCI directory to a place where it is normally stored (and where Linux can find it).''
The DOS utility movepci.exe is apparently in Compaq's support package SP1599.EXE if you still need
it.
E22** 38
Linux Ethernet−Howto
More general information on the AMD chips can be found in AMD LANCE.
These systems use a Texas Instruments ThunderLAN chip Information on the ThunderLAN driver can be
found in ThunderLAN.
Check your card − if it has part number 323551−821 and/or an intel 82558 chip on it then it is another Intel
EEPro100 based card.
4.14 Danpex
Danpex EN9400
Status: Supported, Driver Name: de4x5, tulip
Yet another card based on the DEC 21040 chip, reported to work fine, and at a relatively cheap price.
See DEC 21040 for more information on these cards, and the present driver situation.
4.15 Davicom
Davicom DM9102
Status: Supported, Driver Name: tulip, dmfe
This is an almost clone of the tulip chip and so you can use the tulip driver or the vendor supplied dmfe driver.
Usual advice is to try tulip first, and then try dmfe. Apparently dmfe is only better for very very old cards.
4.16 D−Link
DE−100, DE−200, DE−220−T, DE−250
Status: Supported, Driver Name: ne (+8390)
Some of the early D−Link cards didn't have the 0x57 PROM signature, but the ne2000 driver knows about
them. For the software configurable cards, you can get the config program from www.dlink.com. Note that
there are also cards from Digital (DEC) that are also named DE100 and DE200, but the similarity stops there.
DE−520
Status: Supported, Driver Name: pcnet32
This is a PCI card using the PCI version of AMD's LANCE chip. DMA selection and chip numbering
information can be found in AMD LANCE.
DE−528
Status: Supported, Driver Name: ne, ne2k−pci (+8390)
DE−530
Status: Supported, Driver Name: de4x5, tulip
This is a generic DEC 21040 PCI chip implementation, and is reported to work with the generic 21040 tulip
driver. Note that this is NOT the DFE−530.
See DEC 21040 for more information on these cards, and the present driver situation.
DE−600
Status: Supported, Driver Name: de600
The DE600 is an old parallel port ethernet adaptor made for laptop users etc. Expect about 180kb/s transfer
speed from this device. You should read the README.DLINK file in the kernel source tree. Note that the
device name that you pass to ifconfig is now eth0 and not the previously used dl0.
DE−620
Status: Supported, Driver Name: de620
Similar to the the DE−600, only with two output formats. See the above information on the DE−600.
DE−650
Status: Supported, Driver Name: pcnet_cs
Some people have been using this PCMCIA card for some time now with their notebooks. It is a basic 8390
design, much like a NE2000. The LinkSys PCMCIA card and the IC−Card Ethernet are supposedly DE−650
clones as well.
DFE−530TX
Status Supported, Driver Name: via−rhine
DE−520 40
Linux Ethernet−Howto
Another card using the VIA Rhine chipset. Newer cards use the Rhine−II. (see VIA Rhine) Don't confuse this
with the DE−530 which is a tulip based card, or the DFE−530+ which is an 8139.
DFE−530TX+, DFE−538TX
Status Supported, Driver Name: 8139too, rtl8139(old)
This card uses the RealTek 8139 chip − see the section RealTek 8139.
DFE−550TX
Status Supported, Driver Name: sundance
DFE−570TX
Status Supported, Driver Name: tulip
DFE−580TX
Status Supported, Driver Name: sundance
DGE−500T
Status: Supported, Driver Name: ns83820
DGE−550T
Status Supported, Driver Name: dl2k
4.17 DFI
DFINET−300 and DFINET−400
Status: Supported, Driver Name: ne (+8390)
Yet another poor NE clone card − these use `DFI' in the first 3 bytes of the prom, instead of using 0x57 in
bytes 14 and 15, which is what all the NE1000 and NE2000 cards should use. (The 300 is an 8 bit pseudo
NE1000 clone, and the 400 is a pseudo NE2000 clone.)
DFE−530TX+, DFE−538TX 41
Linux Ethernet−Howto
There is documentation included in the source file `depca.c', which includes info on how to use more than one
of these cards in a machine. Note that the DE422 is an EISA card. These cards are all based on the AMD
LANCE chip. See AMD LANCE for more info. A maximum of two of the ISA cards can be used, because
they can only be set for 0x300 and 0x200 base I/O address. If you are intending to do this, please read the
notes in the driver source file depca.c in the standard kernel source tree.
This driver will also work on Alpha CPU based machines, and there are various ioctl()s that the user can play
with.
These cards use a proprietary chip from DEC, as opposed to the LANCE chip used in the earlier cards like the
DE200. These cards support both shared memory or programmed I/O, although you take about a
50%performance hit if you use PIO mode. The shared memory size can be set to 2kB, 32kB or 64kB, but only
2 and 32 have been tested with this driver. David says that the performance is virtually identical between the
2kB and 32kB mode. There is more information (including using the driver as a loadable module) at the top of
the driver file ewrk3.c and also in README.ewrk3. Both of these files come with the standard kernel
distribution. This driver has Alpha CPU support like depca.c does.
The standard driver has a number of interesting ioctl() calls that can be used to get or clear packet statistics,
read/write the EEPROM, change the hardware address, and the like. Hackers can see the source code for more
info on that one.
David has also written a configuration utility for this card (along the lines of the DOS program
NICSETUP.EXE) along with other tools. These can be found on most Linux FTP sites in the directory
/pub/Linux/system/Network/management −− look for the file ewrk3tools−X.XX.tar.gz.
These cards are based on the 21040 chip mentioned below. The DE500 uses the 21140 chip to provide
10/100Mbs ethernet connections. Have a read of the 21040 section below for extra info. There are also some
compile−time options available for non−DEC cards using this driver. Have a look at README.de4x5 for
details.
All the Digital cards will autoprobe for their media (except, temporarily, the DE500 due to a patent issue).
This driver is also Alpha CPU ready and supports being loaded as a module. Users can access the driver
internals through ioctl() calls − see the 'ewrk3' tools and the de4x5.c sources for information about how to do
this.
The DEC 21040 is a bus−mastering single chip ethernet solution from Digital, similar to AMD's PCnet chip.
The 21040 is specifically designed for the PCI bus architecture. Apparently these chips are no longer being
You have a choice of two drivers for cards based on this chip. There is the DE425 driver discussed above, and
the generic 21040 `tulip' driver.
Warning: Even though your card may be based upon this chip, the drivers may not work for you. David C.
Davies writes:
``There are no guarantees that either `tulip.c' OR `de4x5.c' will run any DC2114x based card other than those
they've been written to support. WHY?? You ask. Because there is a register, the General Purpose Register
(CSR12) that (1) in the DC21140A is programmable by each vendor and they all do it differently (2) in the
DC21142/3 this is now an SIA control register (a la DC21041). The only small ray of hope is that we can
decode the SROM to help set up the driver. However, this is not a guaranteed solution since some vendors
(e.g. SMC 9332 card) don't follow the Digital Semiconductor recommended SROM programming format."
In non−technical terms, this means that if you aren't sure that an unknown card with a DC2114x chip will
work with the linux driver(s), then make sure you can return the card to the place of purchase before you pay
for it.
The 21041 chip is also found in place of the 21040 on most of the later SMC EtherPower cards. The 21140 is
for supporting 100Base−T and works with the Linux drivers for the 21040 chip. To use David's de4x5 driver
with non−DEC cards, have a look at README.de4x5 for details.
If you are having trouble with the tulip driver, you can try the newest version from Donald's ftp/WWW site.
Tulip Driver
There is also a (non−exhaustive) list of various cards/vendors that use the 21040 chip.
4.19 Farallon
Farallon sells EtherWave adaptors and transceivers. This device allows multiple 10baseT devices to be
daisy−chained.
Farallon Etherwave
Status: Supported, Driver Name: 3c509
This is reported to be a 3c509 clone that includes the EtherWave transceiver. People have used these
successfully with Linux and the present 3c509 driver. They are too expensive for general use, but are a great
option for special cases. Hublet prices start at $125, and Etherwave adds $75−$100 to the price of the board
−− worth it if you have pulled one wire too few, but not if you are two network drops short.
It has been reported that this card was detected with the de4x5 driver.
4.19 Farallon 43
Linux Ethernet−Howto
4.20 Fujitsu
Unlike many network chip manufacturers, Fujitsu have also made and sold some network cards based upon
their chip.
Fujitsu FMV−181/182/183/184
Status: Supported, Driver Name: at1700, fmv18x(old)
According to the driver, these cards are a straight forward Fujitsu MB86965 implementation, which would
make them very similar to the Allied Telesis AT1700 cards.
Older kernels used the driver fmv18x but support for these cards was added to the at1700 driver and so the
former has been phased out.
27245A
Status: Supported, Driver Name: hp (+8390)
8 bit 8390 based 10BaseT, not recommended for all the 8 bit reasons.
The HP PC Lan+ is different to the standard HP PC Lan card. It can be operated in either a PIO mode like a
ne2000, or a shared memory mode like a wd8013.
HP−J2405A
Status: Supported, Driver Name: lance
These are lower priced, and slightly faster than the 27247/27252A, but are missing some features, such as
AUI, ThinLAN connectivity, and boot PROM socket. This is a fairly generic LANCE design, but a minor
design decision makes it incompatible with a generic `NE2100' driver. Special support for it (including
reading the DMA channel from the board) is included thanks to information provided by HP's Glenn Talbott.
4.20 Fujitsu 44
Linux Ethernet−Howto
The HP−Vectra has an AMD PCnet chip on the motherboard. DMA selection and chip numbering
information can be found in AMD LANCE.
HP 10/100 VG Any Lan Cards (27248B, J2573, J2577, J2585, J970, J973)
Status: Supported, Driver Name: hp100
This driver also supports some of the Compex VG products. Since the driver supports ISA, EISA and PCI
cards, it is found under ISA cards when running make config on a kernel source.
Apparently these are just a rebadged Intel EtherExpress Pro 10/100B card. See the Intel section for more
information.
This is intel i82593 based. It has been declared obsolete in the 2.4 series kernels.
This card is reported to be compatible with the Intel EtherExpress Pro 100 driver.
To support token ring requires more than only writing a device driver, it also requires writing the source
routing routines for token ring. It is the source routing that would be the most time comsuming to write.
Initial driver development was done with IBM ISA and MCA token ring cards, and tested on an MCA 16/4
Megabit Token Ring board, but it should work with other Tropic based boards.
This driver supports both the ISA (16i) and EISA (32) versions of the card. It uses the Fujitsu MB86965 chip
that is also used on the at1700 cards.
Ether Express
Status: Supported, Driver Name: eexpress
This card uses the intel i82586. Earlier versions of this driver (in v1.2 kernels) were classed as alpha−test, as it
didn't work well for most people. The driver in the v2.0 kernel seems to work much better for those who have
tried it, although the driver source still lists it as experimental and more problematic on faster machines.
The comments at the top of the driver source list some of the problems (and fixes!) associated with these
cards. The slowdown hack of replacing all the outb with outb_p in the driver has been reported to avoid
lockups for at least one user. Also check that the size of the RAM buffer reported by the driver matches what
the Intel configuration utility reports.
Bao Chau Ha has written a driver for these cards that has been included into early 1.3.x kernels. It may also
work with some of the Compaq built−in ethernet systems that are based on the i82595 chip. You may have to
use the configuration utility that came with the card to disable PnP support where applicable.
There is a driver for the PCI version that is distributed separately from the default kernel. These cards use the
PLX9036 PCI interface chip with the Intel i82596 LAN controller chip. If your card has the i82557 chip, then
you don't have this card, but rather the version discussed next, and hence want the EEPro100 driver instead.
You can get the alpha driver for the PRO/10 PCI card, along with instructions on how to use it at:
EEPro10 Driver
If you have the EISA card, you will probably have to hack the driver a bit to account for the different (PCI vs.
EISA) detection mechanisms that are used in each case.
The e100 driver was supplied by intel, and the eepro100 driver is the original driver by Donald. Note that the
eepro100 driver will not work with the older 100A cards. The chip numbers listed in the driver are i82557,
i82558, i82559, i82801, and about 25 other PCI IDs. For driver updates and/or driver support, have a look at:
EEPro−100B Page
E1000 Gigabit
Status: Supported, Driver Name: e1000
4.25 Kingston
Kingston make various cards, including NE2000+, AMD PCnet based cards, and DEC tulip based cards. Most
of these cards should work fine with their respective driver. See Kingston Web Page
4.26 LinkSys
LinkSys make a handful of different NE2000 clones, some straight ISA cards, some ISA plug and play and
some even ne2000−PCI clones based on one of the supported ne2000−PCI chipsets. There are just too many
models to list here. Their site is at http://www.linksys.com/
Note that with these cards there have been several `revisions' (i.e. different chipset used) all with the same
card name. The 1st used the DEC chipset. The 2nd revision used the Lite−On PNIC 82c168 PCI Network
Interface Controller, the 3rd revision of the card uses a LinkSys 82c169 NIC chip, and the 4th revision uses
the ADMtek Comet. Support for the latter three has been merged into the standard tulip driver −− you may
need a driver upgrade to get support for them depending on how old your current driver version is.
http://www.scyld.com/network
More information on the various versions of these cards can be found at the LinkSys WWW site mentioned
above.
This is supposedly a DE−620 clone, and is reported to work well with that driver. See DE−620 for more
information.
Another i82586 based card. Dirk Niggemann dirk−[email protected] has written a driver that he classes
as ``pre−alpha'' that he would like people to test. Mail him for more details.
4.28 Mylex
Mylex can be reached at the following numbers, in case anyone wants to ask them anything.
These are fairly old EISA cards that make use of a shared memory implementation similar to the wd80x3. A
driver for these cards is available in the current 2.1.x series of kernels. Ensure you set the shared memory
address below 1MB or above the highest address of the physical RAM installed in the machine.
Mylex LNP101
Status: Supported, Driver Name: de4x5, tulip
This is a PCI card that is based on DEC's 21040 chip. It is selectable between 10BaseT, 10Base2 and 10Base5
output. The LNP101 card has been verified to work with the generic 21040 driver.
See the section on the 21040 chip ( DEC 21040) for more information.
Mylex LNP104
Status: Semi−Supported, Driver Name: de4x5, tulip
The LNP104 uses the DEC 21050 chip to deliver four independent 10BaseT ports. It should work with recent
21040 drivers that know how to share IRQs, but nobody has reported trying it yet (that I am aware of).
4.29 Myson
Myson MTD−8xx 10/100 PCI
Status: Supported, Driver Name: fealnx
Apparently cards sold under the name Surecom EP−320X−S also use this Myson chip.
The infamous 8390 chip. Found on a zillion ISA cards, and cloned by various other chip manufacturers. Note
that the file 8390.o is not a complete driver in itself. It has to be used in conjunction with another driver that
knows how the 8390 is interfaced to the computer bus. Examples of the 2nd half of the driver are wd.o,
3c503.o, smc−ultra.o, ne2k−pci.o and so on.
DP83815/83816
Status: Supported, Driver Name: natsemi
http://www.scyld.com/network/natsemi.html
NS83820, DP83820
Status: Supported, Driver Name: ns83820
Mylex LNP104 49
Linux Ethernet−Howto
The 83820 is a 10/100/1000 Mbps 64 bit PCI ethernet NIC, and the 83821 is a 32 bit PCI part (but it appears
that the parts are identical and the EEPROM is supposed to set the data path width). Just like the 8390, you
won't usually see this number unless you look at the chip on the card.
NE1000, NE2000
Status: Supported, Driver Name: ne (+8390)
The ne2000 is now a generic name for a bare−bones design around the NatSemi 8390 chip. They use
programmed I/O rather than shared memory, leading to easier installation but slightly lower performance and
a few problems. Some of the more common problems that arise with NE2000 cards are listed in Problems
with...
Some NE2000 clones use the National Semiconductor `AT/LANTic' 83905 chip, which offers a shared
memory mode similar to the wd8013 and EEPROM software configuration. The shared memory mode will
offer less CPU usage (i.e. more efficient) than the programmed I/O mode.
In general it is not a good idea to put a NE2000 clone at I/O address 0x300 because nearly every device
driver probes there at boot. Some poor NE2000 clones don't take kindly to being prodded in the wrong areas,
and will respond by locking your machine. Also 0x320 is bad because SCSI drivers probe into 0x330.
Donald has written a NE2000 diagnostic program (ne2k.c) for all ne2000 cards. See Diagnostic Programs for
more information.
If you intend on using this driver as a loadable module you should probably see Using the Ethernet Drivers as
Modules for module specific information.
NE2000−PCI (RealTek/Winbond/Compex)
Status: Supported, Driver Name: ne, ne2k−pci (+8390)
Yes, believe it or not, people are making PCI cards based on the more than ten year old interface design of the
ne2000. At the moment nearly all of these cards are based on the RealTek 8029 chip, or the Winbond 89c940
chip. The Compex, KTI, VIA and Netvin cards apparently also use these chips, but have a different PCI ID.
The latest v2.0 kernel has support to automatically detect all these cards and use them. (If you are using a
kernel v2.0.34 or older, you should upgrade to ensure your card will be detected.) There are now two drivers
to choose from; the original ISA/PCI ne.c driver, and a relatively new PCI−only ne2k−pci.c driver.
To use the original ISA/PCI driver you have to say `Y' to the `Other ISA cards' option when running make
config as you are actually using the same NE2000 driver as the ISA cards use. (That should also give you a
hint that these cards aren't anywhere as intelligent as say a PCNet−PCI or DEC 21040 card...)
http://www.scyld.com/network
If you have a NE2000 PCI card that is not detected by the most current version of the driver, please contact
the maintainer of the NE2000 driver as listed in /usr/src/linux/MAINTAINERS along with the output
from a cat /proc/pci and dmesg so that support for your card can also be added to the driver.
Also note that various card makers have been known to put `NE2000 Compatible' stickers on their product
boxes even when it is completely different (e.g. PCNet−PCI or RealTek 8139). If in doubt check the main
chip number against this document.
NE−10/100
Status: Not Supported.
These are ISA 100Mbps cards based on the National Semiconductor DP83800 and DP83840 chips. There is
currently no driver support, nor has anyone reported that they are working on a driver. Apparently
documentation on the chip is unavailable with the exception of a single PDF file that doesn't give enough
details for a driver.
NE1500, NE2100
Status: Supported, Driver Name: lance
These cards use the original 7990 LANCE chip from AMD and are supported using the Linux lance driver.
Newer NE2100 clones use the updated PCnet/ISA chip from AMD.
Some earlier versions of the lance driver had problems with getting the IRQ line via autoIRQ from the
original Novell/Eagle 7990 cards. Hopefully this is now fixed. If not, then specify the IRQ via LILO, and let
us know that it still has problems.
DMA selection and chip numbering information can be found in AMD LANCE.
NE/2 MCA
Status: Semi−Supported, Driver Name: ne2
There were a few NE2000 microchannel cards made by various companies. This driver, available in v2.2
kernels, will detect the following MCA cards: Novell Ethernet Adapter NE/2, Compex ENET−16 MC/P, and
the Arco Ethernet Adapter AE/2.
NE−10/100 51
Linux Ethernet−Howto
NE3200
Status: Not Supported.
While there is no driver support in the current 2.4 kernel, Rask Ingemann Lambertsen has been playing
around with an old EISA machine and had an experimental driver at:
http://vip.cybercity.dk/~ccc94453/linux/ne3200/
NE3210
Status: Supported, Driver Name: ne3210 (+8390)
This EISA card is completely different from the NE3200, as it uses a Nat Semi 8390 chip. The driver can be
found in the v2.2 kernel source tree. Ensure you set the shared memory address below 1MB or above the
highest address of the physical RAM installed in the machine.
NE4100
Status: Supported, Driver Name: pcnet_cs
NE5500
Status: Supported, Driver Name: pcnet32
These are just AMD PCnet−PCI cards ('970A) chips. More information on LANCE/PCnet based cards can be
found in AMD LANCE.
4.32 Netgear
Netgear FA−311
Status: Supported, Driver Name: natsemi
Netgear GA−620
Status: Supported, Driver Name: acenic
Netgear GA−621
Status: Supported, Driver Name: ns83820
4.33 Proteon
Proteon P1370−EA
Status: Supported, Driver Name: ne (+8390)
NE3200 52
Linux Ethernet−Howto
Proteon P1670−EA
Status: Supported, Driver Name: de4x5, tulip
This is yet another PCI card that is based on DEC's Tulip chip. It has been reported to work fine with Linux.
See the section on the 21040 chip ( DEC 21040) for more driver information.
The PureData PDUC8028 and PDI8023 series of cards are `almost clones' of the wd80x3 cards − there is
special code in the wd.c driver to probe for these cards.
4.35 Racal−Interlan
Racal Interlan can be reached via WWW at www.interlan.com. I believe they were also known as
MiCom−Interlan at one point in the past.
ES3210
Status: Semi−Supported, Driver Name: es3210
This is an EISA 8390 based shared memory card. An experimetal driver is shipped with v2.2 kernels and it is
reported to work fine, but the EISA IRQ and shared memory address detection appears not to work with (at
least) the early revision cards. (This problem is not unique to the Linux world either...) In that case, you have
to supply them to the driver. For example, card at IRQ 5 and shared memory 0xd0000, with a modular
driver, add options es3210 irq=5 mem=0xd0000 to /etc/modules.conf. Or with the driver
compiled into the kernel, supply at boot ether=5,0,0xd0000,eth0 The I/O base is automatically
detected and hence a value of zero should be used.
NI5010
Status: Semi−Supported, Driver Name: ni5010
You used to have to go get the driver for these old 8 bit MiCom−Interlan cards separately, but now it is
shipped with the v2.2 kernels as an experimental driver.
NI5210
Status: Semi−Supported, Driver Name: ni52
This card also uses one of the Intel chips. Michael Hipp has written a driver for this card. It is included in the
Proteon P1670−EA 53
Linux Ethernet−Howto
standard kernel as an `alpha' driver. Michael would like to hear feedback from users that have this card. See
Alpha Drivers for important information on using alpha−test ethernet drivers with Linux.
There is also a driver for the LANCE based NI6510, and it is also written by Michael Hipp. Again, it is also
an `alpha' driver. For some reason, this card is not compatible with the generic LANCE driver. See Alpha
Drivers for important information on using alpha−test ethernet drivers with Linux.
As of kernel 1.3.23, the generic LANCE driver had a check added to it for the 0x52, 0x44 NI6510EB
specific signature. Others have reported that this signature is not the same for all NI6510EB cards however,
which will cause the lance driver to not detect your card. If this happens to you, you can change the probe (at
about line 322 in lance.c) to printk() out what the values are for your card and then use them instead of the
0x52, 0x44 defaults.
The cards should probably be run in `high−performance' mode and not in the NI6510 compatible mode when
using the lance driver.
4.36 RealTek
RealTek RTL8002/8012 (AT−Lan−Tec) Pocket adaptor
Status: Supported, Driver Name: atp
This is a generic, low−cost OEM pocket adaptor being sold by AT−Lan−Tec, and (likely) a number of other
suppliers. A driver for it is included in the standard kernel. Note that there is substantial information contained
in the driver source file `atp.c'.
Note that the device name that you pass to ifconfig was not eth0 but atp0 for earlier versions of this
driver.
RealTek 8008
Status: Supported, Driver Name: ne, wd (+8390)
This chip has been reported to behave similar to the AT/LANTIC in that it can be set for ne/PIO or wd/MMIO
modes of operation via the vendor supplied software (SET8008R).
RealTek 8009
Status: Supported, Driver Name: ne (+8390)
This is an ISA NE2000 clone, and is reported to work fine with the linux NE2000 driver. The
rset8009.exe program can be obtained from RealTek's WWW site at
http://www.realtek.com.tw − or via ftp from the same site.
RealTek 8019
Status: Supported, Driver Name: ne (+8390)
This is a Plug and Pray version of the above. Use the DOS software to disable PnP and enable jumperless
configuration; set the card to a sensible I/O address and IRQ and you should be ready to go. (If using the
driver as a module, don't forget to add an io=0xNNN option to /etc/modules.conf). The
rset8019.exe program can be obtained from RealTek's WWW site at
http://www.realtek.com.tw − or via ftp from the same site.
RealTek 8029
Status: Supported, Driver Name: ne, ne2k−pci (+8390)
This is a PCI single chip implementation of a NE2000 clone. Various vendors are now selling cards with this
chip. See NE2000−PCI for information on using any of these cards. Note that this is still a 10+ year old
design just glued onto a PCI bus. Performance won't be staggeringly better than the equivalent ISA model.
RealTek 8129/8139
Status: Supported, Driver Name: 8139too, rtl8139(old)
Another PCI single chip ethernet solution from RealTek. A driver for cards based upon this chip was included
in the v2.0.34 release of linux. The driver is called 8139too in recent kernels.
In older kernels, the driver was called rtl8139 and you generally had to to answer `Y' when asked if you
want experimental drivers to get access to this driver.
4.37 Sager
Sager NP943
Status: Semi−Supported, Driver Name: 3c501
This is just a 3c501 clone, with a different S.A. PROM prefix. I assume it is equally as brain dead as the
original 3c501 as well. The driver checks for the NP943 I.D. and then just treats it as a 3c501 after that. See
3Com 3c501 for all the reasons as to why you really don't want to use one of these cards.
RealTek 8019 55
Linux Ethernet−Howto
This driver was included into the v1.1 kernels, and it was written by PJD Weichmann and SWS Bern. It
appears that the SK G16 is similar to the NI6510, in that it is based on the first edition LANCE chip (the
7990). Once again, it appears as though this card won't work with the generic LANCE driver.
4.39 SEEQ
SEEQ 8005
Status: Obsolete, Driver Name: seeq8005
There is little information about the card included in the driver, and hence little information to be put here. If
you have a question, you are probably best trying to e−mail the driver author as listed in the source.
This device can be found as a standalone PCI card, or as built−in on the motherboard. The driver has been
present since late 2.2 kernels.
SMC / Standard Microsystems Corp., 80 Arkay Drive, Hauppage, New York, 11788, USA. Technical Support
via phone: 800−992−4762 (USA) or 800−433−5345 (Canada) or 516−435−6250 (Other Countries). Literature
requests: 800−SMC−4−YOU (USA) or 800−833−4−SMC (Canada) or 516−435−6255 (Other Countries).
Technical Support via E−mail: [email protected]. FTP Site: ftp.smc.com. WWW
Site: SMC.
These are the 8−bit versions of the card. The 8 bit 8003 is slightly less expensive, but only worth the savings
4.39 SEEQ 56
Linux Ethernet−Howto
for light use. Note that some of the non−EEPROM cards (clones with jumpers, or old old old wd8003 cards)
have no way of reporting the IRQ line used. In this case, auto−irq is used, and if that fails, the driver silently
assings IRQ 5. You can get the SMC setup/driver disks from SMC's ftp site. Note that some of the newer
SMC `SuperDisk' programs will fail to detect the real old EEPROM−less cards. The file SMCDSK46.EXE
seems to be a good all−round choice. Also the jumper settings for all their cards are in an ASCII text file in
the aforementioned archive. The latest (greatest?) version can be obtained from ftp.smc.com.
As these are basically the same as their 16 bit counterparts (WD8013 / SMC Elite16), you should see the next
section for more information.
Over the years the design has added more registers and an EEPROM. (The first wd8003 cards appeared about
ten years ago!) Clones usually go by the `8013' name, and usually use a non−EEPROM (jumpered) design.
Late model SMC cards will have the SMC 83c690 chip instead of the original Nat Semi DP8390 found on
earlier cards. The shared memory design makes the cards a bit faster than PIO cards, especially with larger
packets. More importantly, from the driver's point of view, it avoids a few bugs in the programmed−I/O mode
of the 8390, allows safe multi−threaded access to the packet buffer, and it doesn't have a programmed−I/O
data register that hangs your machine during warm−boot probes.
Non−EEPROM cards that can't just read the selected IRQ will attempt auto−irq, and if that fails, they will
silently assign IRQ 10. (8 bit versions will assign IRQ 5)
Cards with a non standard amount of memory on board can have the memory size specified at boot (or as an
option in /etc/modules.conf if using modules). The standard memory size is 8kB for an 8bit card and
16kB for a 16bit card. For example, the older WD8003EBT cards could be jumpered for 32kB memory. To
make full use of that RAM, you would use something like (for I/O=0x280 and IRQ 9):
Also see 8013 problems for some of the more common problems and frequently asked questions that pop up
often.
If you intend on using this driver as a loadable module you should probably see Using the Ethernet Drivers as
Modules for module specific information.
This ethercard is based on the 83c790 chip from SMC, which has a few new features over the 83c690. While
it has a mode that is similar to the older SMC ethercards, it's not entirely compatible with the old WD80*3
drivers. However, in this mode it shares most of its code with the other 8390 drivers, while operating slightly
faster than a WD8013 clone.
Since part of the Ultra looks like an 8013, the Ultra probe is supposed to find an Ultra before the wd8013
probe has a chance to mistakenly identify it.
Bus−Master SCSI host adaptor users take note: In the manual that ships with Interactive UNIX, it mentions
that a bug in the SMC Ultra will cause data corruption with SCSI disks being run from an aha−154X host
adaptor. This will probably bite aha−154X compatible cards, such as the BusLogic boards, and the
AMI−FastDisk SCSI host adaptors as well.
SMC has acknowledged the problem occurs with Interactive, and older Windows NT drivers. It is a hardware
conflict with early revisions of the card that can be worked around in the driver design. The current Ultra
driver protects against this by only enabling the shared memory during data transfers with the card. Make sure
your kernel version is at least 1.1.84, or that the driver version reported at boot is at least
smc−ultra.c:v1.12 otherwise you are vulnerable.
If you intend on using this driver as a loadable module you should probably see Using the Ethernet Drivers as
Modules for module specific information.
This EISA card shares a lot in common with its ISA counterpart. A working (and stable) driver is included in
both v2.0 and v2.2 kernels. Thanks go to Leonard Zubkoff for purchasing some of these cards so that linux
support could be added for them.
This card uses SMC's 83c795 chip and supports the Plug 'n Play specification. It also has an SMC Ultra
compatible mode, which allows it to be used with the Linux Ultra driver. For best results, use the SMC
supplied program (avail. from their www/ftp site) to disable PnP and configure it for shared memory mode.
See the above information for notes on the Ultra driver.
For v1.2 kernels, the card had to be configured for shared memory operation. However v2.0 kernels can use
the card in shared memory or programmed I/O mode. Shared memory mode will be slightly faster, and use
less CPU resources as well.
NB: The EtherPower II is an entirely different card. See below! These cards are a basic DEC 21040
implementation, i.e. one big chip and a couple of transceivers. Donald has used one of these cards for his
development of the generic 21040 driver (aka tulip.c). Thanks to Duke Kamstra, once again, for supplying
a card to do development on.
Some of the later revisons of this card use the newer DEC 21041 chip, which may cause problems with older
versions of the tulip driver. If you have problems, make sure you are using the latest driver release, which may
not yet be included in the current kernel source tree.
See DEC 21040 for more details on using one of these cards, and the current status of the driver.
Apparently, the latest revision of the card, the EtherPower−II uses the 9432 chip. It is unclear at the moment if
this one will work with the present driver. As always, if unsure, check that you can return the card if it doesn't
work with the linux driver before paying for the card.
These cards, based upon the SMC 83c170 chip, are entirely different than the Tulip based cards. A new driver
has been included in kernels v2.0 and v2.2 to support these cards. For more details, see:
http://www.scyld.com/network
Apparently SMC is no longer the same company that brought you cards like the Ultra and the EPIC. The chip
design part is now called SMSC and you will see the SMC name stuck on low end OEM boards like this one
− a RealTek 8139 with a modified EEPROM.
SMC 3008
Status: Not Supported.
These 8 bit cards are based on the Fujitsu MB86950, which is an ancient version of the MB86965 used in the
Linux at1700 driver. Russ says that you could probably hack up a driver by looking at the at1700.c code and
his DOS packet driver for the Tiara card (tiara.asm). They are not very common.
SMC 3016
Status: Not Supported.
These are 16bit I/O mapped 8390 cards, much similar to a generic NE2000 card. If you can get the
specifications from SMC, then porting the NE2000 driver would probably be quite easy. They are not very
common.
The SMC9000 is a VLB card based on the 91c92 chip. The 91c92 appears on a few other brand cards as well,
but is fairly uncommon.
SMC 91c100
Status: Semi−Supported, Driver Name: smc9194
The SMC 91c92 driver is supposed to work for cards based on this 100Base−T chip, but at the moment this is
unverified.
SMC 9452TX/9462TX
Status: Supported, Driver Name: ns83820
4.42 Sundance
Sundance ST201, Alta
Status: Supported, Driver Name: sundance
The Sundance Alta chip is used on OEM boards. It uses bus−master transfers, can transmit from and receive
into arbitrarily aligned buffers, and has a 64 element multicast hash. All chip versions have flow control and
ACPI power states.
4.43 SysKonnect
SysKonnect sk−98xx Gigabit Ethernet
Status: Supported, Driver Name: sk98
Early reports indicated that this chipset had a problem with Tx checksums, which hurts performance a little.
This driver covers many Compaq built−in ethernet devices, including the NetFlex and Netelligent groups. It
also supports the Olicom 2183, 2185, 2325 and 2326 products.
See the section on the 21040 chip ( DEC 21040) for more information.
SMC 91c100 60
Linux Ethernet−Howto
4.46 VIA
You probably won't see a VIA networking card, as VIA make several networking chips that are then used by
others in the construction of an ethernet card. They have a WWW site at:
http://www.via.com.tw/
This controller chip is VIA's PCI−NE2000 offering. You can choose between the ISA/PCI ne.c driver or the
PCI−only ne2k−pci.c driver. See the PCI−NE2000 section for more details.
This relatively new driver can be found in current 2.0 and 2.1 kernels. It is an improvement over the 86C926
NE2000 chip in that it supports bus master transfers, but strict 32 bit buffer alignment requirements limit the
benefit gained from this. For more details and driver updates, see:
http://www.scyld.com/network
4.48 Winbond
Winbond don't really make and sell complete cards to the general public −− instead they make single chip
ethernet solutions that other companies buy, stick onto a PCI board with their own name and then sell through
retail stores. Some setup programs and tech support is available at:
http://www.winbond.com.tw
Winbond 89c840
Status: Supported, Driver Name: winbond−840
This chip has been described as `the mutant spawn of a NE2000 and a Tulip clone' −− see the driver notes for
more details. This driver also supports the TX9882 chip found on the Compex RL100−ATX.
4.46 VIA 61
Linux Ethernet−Howto
These are Winbond's ISA 10Mbps ne2000 compatible ethernet chips. Setup programs are available at the
Winbond site.
Winbond 89c940
Status: Supported, Driver Name: ne, ne2k−pci (+8390)
This chip is one of the two commonly found on the low price PCI ne2000 cards sold by lots of manufacturers.
Note that this is still a 10+ year old design just glued onto a PCI bus. Performance won't be staggeringly better
than the equivalent ISA model.
4.49 Xircom
For the longest time, Xircom wouldn't release the programming information required to write a driver, unless
you signed your life away. Apparently enough linux users have pestered them for driver support (they claim to
support all popular networking operating systems...) so that they have changed their policy to allow
documentation to be released without having to sign a non−disclosure agreement. Some people have said they
they will release the source code to the SCO driver, while others have been told that they are no longer
providing information on `obsolete' products like the earlier PE models. If you are interested and want to
check into this yourself, you can reach Xircom at 1−800−874−7875, 1−800−438−4526 or +1−818−878−7600.
Not to get your hopes up, but if you have one of these parallel port adaptors, you may be able to use it in the
DOS emulator with the Xircom−supplied DOS drivers. You will have to allow DOSEMU access to your
parallel port, and will probably have to play with SIG (DOSEMU's Silly Interrupt Generator).
According to the driver, this supports the CE2, CE IIps, RE−10, CEM28, CEM33, CE33, CEM56, CE3−100,
CE3B, RE−100, REM10BT, and the REM56G−100.
Xircom CBE−100
Status: Supported, Driver Name: xircom_tulip_cb
4.50 Zenith
Z−Note
Status: Obsolete, Driver Name: znet
Winbond 89c940 62
Linux Ethernet−Howto
The built−in Z−Note network adaptor is based on the Intel i82593 using two DMA channels. Also note that
the IBM ThinkPad 300 is compatible with the Z−Note.
4.51 Znyx
Znyx ZX342 (DEC 21040 based)
Status: Supported, Driver Name: de4x5, tulip
You have a choice of two drivers for cards based on this chip. There is the DE425 driver written by David,
and the generic 21040 driver that Donald has written.
Note that as of 1.1.91, David has added a compile time option that may allow non−DEC cards (such as the
Znyx cards) to work with this driver. Have a look at README.de4x5 for details.
See DEC 21040 for more information on these cards, and the present driver situation.
First of all, look for any obvious model numbers that might give a clue. Any model number that contains 2000
will most likely be a NE2000 clone. Any cards with 8003 or 8013 on them somewhere will be
Western/Digital WD80x3 cards or SMC Elite cards or clones of them.
Probably the most common ISA NIC is the National Semiconductor DP8390 aka NS32490 aka DP83901 aka
DP83902 aka DP83905 aka DP83907. And those are just the ones made by National! Other companies such
as Winbond and UMC make DP8390 and DP83905 clone parts, such as the Winbond 89c904 (DP83905
clone) and the UMC 9090. If the card has some form of 8390 on it, then chances are it is a ne1000 or ne2000
clone card. The second most common 8390 based card are wd80x3 cards and clones. Cards with a DP83905
can be configured to be an ne2000 or a wd8013. Never versions of the genuine wd80x3 and SMC Elite cards
have an 83c690 in place of the original DP8390. The SMC Ultra cards have an 83c790, and use a slightly
different driver than the wd80x3 cards. The SMC EtherEZ cards have an 83c795, and use the same driver as
the SMC Ultra. All BNC cards based on some sort of 8390 or 8390 clone will usually have an 8392 (or
83c692, or ???392) 16 pin DIP chip very close to the BNC connector.
Another common NIC found on older cards is the Intel i82586. Cards having this NIC include the 3c505,
3c507, 3c523, Intel EtherExpress−ISA, Microdyne Exos−205T, and the Racal−Interlan NI5210.
The original AMD LANCE NIC was numbered AM7990, and newer revisions include the 79c960, 79c961,
79c965, 79c970, and 79c974. Most cards with one of the above will work with the Linux LANCE driver, with
4.51 Znyx 63
Linux Ethernet−Howto
the exception of the old Racal−Interlan NI6510 cards that have their own driver.
Newer PCI cards having a DEC 21040, 21041, 21140, or similar number on the NIC should be able to use the
linux tulip or de4x5 driver.
Other PCI cards having a big chip marked RTL8029 or 89C940 or 86C926 are ne2000 clone cards, and the
ne2k−pci driver should automatically detect these cards.
If your card has a sticker on it giving all six bits of its address, you can look up the vendor from the first three.
However it is more common to see only the last three bytes printed onto a sticker attached to a socketed
PROM, which tells you nothing.
You can determine which vendors have which assigned addresses from RFC−1340. Apparently there is a
more up to date listing available in various places as well. Try a WWW or FTP search for
EtherNet−codes or Ethernet−codes and you will find something.
FCC IDs
If the kernel doesn't detect the card, it may be that the card is not configured to one of the addresses that the
driver probes when looking for a card. In this case, you might want to try getting scanport.tar.gz from
your local linux ftp site, and see if that can locate where your card is jumpered for. It scans ISA I/O space
from 0x100 to 0x3ff looking for devices that aren't registered in /proc/ioports. If it finds an
unknown device starting at some particular address, you can then explicity point the ethernet probes at that
address with an ether= boot argument.
If you manage to get the card detected, you can then usually figure out the unknown jumpers by changing
them one at a time and seeing at what I/O base and IRQ that the card is detected at. The IRQ settings can also
usually be determined by following the traces on the back of the card to where the jumpers are soldered
through. Counting the `gold fingers' on the backside, from the end of the card with the metal bracket, you
have IRQ 9, 7, 6, 5, 4, 3, 10, 11, 12, 15, 14 at fingers 4, 21, 22, 23, 24, 25, 34, 35, 36, 37, 38 respectively.
Jumpers that appear to do nothing usually are for selecting the memory address of an optional boot ROM.
Other jumpers that are located near the BNC or RJ−45 or AUI connectors are usually to select the output
media. These are also typically near the `black box' voltage converters marked YCL, Valor, or Fil−Mag.
A nice collection of jumper settings for various cards can be found at the following URL:
Ethercard Settings
dummy.c − The purpose of this driver is to provide a device to point a route through, but not to actually
transmit packets.
eql.c − Load Equalizer, enslaves multiple devices (usually modems) and balances the Tx load across them
while presenting a single device to the network programs.
ibmtr.c − IBM Token Ring, which is not really ethernet. Broken−Ring requires source routing and other
uglies.
loopback.c − Loopback device, for which all packets from your machine and destined for your own
machine go. It essentially just moves the packet off the Tx queue and onto the Rx queue.
plip.c − Parallel Line Internet Protocol, allows two computers to send packets to each other over two
joined parallel ports in a point−to−point fashion.
ppp.c − Point−to−Point Protocol (RFC1331, 1548. 1661), for the Transmission of Multi−protocol
Datagrams over a Point−to−Point Link (again usually modems).
slip.c − Serial Line Internet Protocol, allows two computers to send packets to each other over two joined
serial ports (usually via modems) in a point−to−point fashion.
tunnel.c − Provides an IP tunnel through which you can tunnel network traffic transparently across
subnets
wavelan.c − An Ethernet−like radio transceiver controlled by the Intel 82586 coprocessor which is used on
other ethercards such as the Intel EtherExpress.
together in a home ethernet. The old−fashioned thick ethernet, RG5 or RG8 cable with N connectors is really
obsolete and rarely seen anymore.
See Type of cable... for an introductory look at cables. Also note that the FAQ from comp.dcom.lans.ethernet
has a lot of useful information on cables and such. FTP to rtfm.mit.edu and look in
/pub/usenet−by−hierarchy/ for the FAQ for that newsgroup.
On the other hand, all 100Mb/sec ethernet proposals use twisted pair, and most new business installations use
twisted pair. The wiring should be listed as Category 5. Anything less than Cat 5 is useless.
If you are only connecting two machines, it is possible to avoid using a hub by purchasing or making a special
cross−over or null cable. But note that some cards that try to sense autonegotiation and so on expect to be
talking to a hub and not another card, and thus may not work in this configuration.
In most cases, if the configuration is done by software, and stored in an EEPROM, you will usually have to
boot DOS, and use the vendor supplied DOS program to set the cards IRQ, I/O, mem_addr and whatnot.
Besides, hopefully it is something you will only be setting once. If you don't have the DOS software for your
card, try looking on the WWW site of your card manufacturer. If you don't know the site name, take a guess at
it, i.e. `www.my_vendor.com' where `my_vendor' is the name of your card manufacturer. This works for
SMC, 3Com, and many many other manufacturers.
There are some cards for which Linux versions of the config utils exist, and they are listed here. Donald has
written a few small card diagnostic programs that run under Linux. Most of these are a result of debugging
tools that he has created while writing the various drivers. Don't expect fancy menu−driven interfaces. You
will have to read the source code to use most of these. Even if your particular card doesn't have a
corresponding diagnostic, you can still get some information just by typing cat /proc/net/dev −−
assuming that your card was at least detected at boot.
In either case, you will have to run most of these programs as root (to allow I/O to the ports) and you probably
want to shut down the ethercard before doing so by typing ifconfig eth0 down first.
Be careful when configuring NE2000+ cards, as you can give them bad setting values which can cause
problems. A typical example is accidentally enabling the boot ROM in the EEPROM (even if no ROM is
installed) to a setting that conflicts with the VGA card. The result is a computer that just beeps at you when
you turn it on and nothing appears on the screen.
You can typically recover from this by doing the following: Remove the card from the machine, and then boot
and enter the CMOS setup. Change the `Display Adapter' to `Not Installed' and change the default boot drive
to `A:' (your floppy drive). Also change the `Wait for F1 if any Error' to `Disabled'. This way, the computer
should boot without user intervention. Now create a bootable DOS floppy (`format a: /s /u') and copy the
program default.exe from the 20XX12.EXE archive above onto that floppy. Then type echo
default > a:autoexec.bat so that the program to set the card back to sane defaults will be run
automatically when you boot from this floppy. Shut the machine off, re−install the ne2000+ card, insert your
new boot floppy, and power it back up. It will still probably beep at you, but eventually you should see the
floppy light come on as it boots from the floppy. Wait a minute or two for the floppy to stop, indicating that it
has finished running the default.exe program, and then power down your computer. When you then turn
Note that if you don't have DOS handy, you can do the whole method above with a linux boot disk that
automatically runs Donald's atlantic program (with the right command line switches) instead of a DOS
boot disk that automatically runs the default.exe program.
3Com Cards
The 3Com Etherlink III family of cards (i.e. 3c5x9) can be configured by using another config utility from
Donald. You can get the file 3c5x9setup.c from Donald's ftp server, www.scyld.com to configure
these cards. (Note that the DOS 3c5x9B config utility may have more options pertaining to the new ``B'' series
of the Etherlink III family.)
Ethercard Diagnostics
HP PCLAN+ −− hp+.c
All Other Cards −− try typing cat /proc/net/dev and dmesg to see what useful info the kernel has on
the card in question.
7. Technical Information
For those who want to understand a bit more about how the card works, or play with the present drivers, this
information should be useful. If you do not fall into this category, then perhaps you will want to skip this
section.
3Com Cards 68
Linux Ethernet−Howto
packets.
Con: Usually the slowest transfer rate, the CPU is waiting the whole time, and interleaved packet access is
usually difficult to impossible.
Con: Uses up memory space (a big one for DOS users, essentially a non−issue under Linux), and it still ties
up the CPU.
Con: (Only applicable to ISA bus cards) Requires low−memory buffers and a DMA channel for cards. Any
bus−master will have problems with other bus−masters that are bus−hogs, such as some primitive SCSI
adaptors. A few badly−designed motherboard chipsets have problems with ISA bus−masters.
Some 8 bit cards that will provide adequate performance for light to average use are the wd8003, the 3c503
and the ne1000. The 3c501 provides poor performance, and these poor 15 year old relics of the XT days
should be avoided. (Send them to Alan, he collects them...)
The 8 bit data path doesn't hurt performance that much, as you can still expect to get about 500 to 800kB/s ftp
download speed to an 8 bit wd8003 card (on a fast ISA bus) from a fast host. And if most of your net−traffic
is going to remote sites, then the bottleneck in the path will be elsewhere, and the only speed difference you
will notice is during net activity on your local subnet.
But an older 10Mbs network doesn't really require a 32 bit interface. See Programmed I/O vs. ... as to why
having a 10Mbps ethercard on an 8MHz ISA bus is really not a bottleneck. Even though having a slow
ethercard on a fast bus won't necessarily mean faster transfers, it will usually mean reduced CPU overhead,
which is good for multi−user systems.
Computing these sums takes time and extra load on the main computer. Some of the more fancy cards have
the ability to do these Rx and/or Tx sums in hardware, which allows the main CPU to offload this task to the
card.
Cards that require a data copy don't benefit as much from hardware checksums, since the sum operation can
be combined into the copy for only a minimal additional overhead. Hence hardware Tx checksums are only
used in zero copy (i.e. applications using sendfile()) situations, and so hardware Rx checksums are
currently more useful.
Note that a reasonable computer can saturate a 100BaseT link even when doing the copy and checksum itself,
so zerocopy/hw−checksum will only show up as decreased CPU use. You would have to go to GigE to see a
speed increase.
As of 2.6 kernels, some drivers have a config option to enable NAPI. There is also some documentation in the
Documentation/networking directory that comes with the kernel.
8. Miscellaneous.
Any other associated stuff that didn't fit in anywhere else gets dumped here. It may not be relevant, and it may
not be of general interest but it is here anyway.
Where the hardware supports it, my drivers have dynamic Tx FIFO tuning code. A typical Ethernet chip has a
Tx FIFO that holds data from the bus before it is transmitted on the wire. The way this FIFO is controlled is
important for performance.
Ideally you would like to start transmitting as soon as the first Tx packet data arrives at the chip. The "Tx
FIFO threshold" is a parameter that specifies "start transmitting when N bytes have arrived at the NIC chip".
This parameter is initially set for a typical configuration. But if a video card or SCSI controller is doing long
PCI bursts, the NIC chip will run out of buffered data before it can get access to the bus again. This causes a
FIFO underrun.
The driver responds to the FIFO underrun by changing the Tx FIFO threshold to a higher value. If this
happens enough eventually the chip will end up in store−and−forward mode, where it doesn't start
transmitting until the whole packet has been transferred.
Some designs, such as the Adaptec Starfire, go one step further and provide an indication that the FIFO almost
ran out of data. This allows the driver to tune the setting without risking a Tx error.
It should be rare to see more than one or two Tx FIFO underruns. Either the chip has very coarse Tx threshold
settings, or the driver increases the setting in large chunks to keep the PCI bursts on natural boundaries.
For example, if the command was `blah' and it expected 3 arguments (say 123, 456, and 789) then, with
LILO, you would use:
8. Miscellaneous. 71
Linux Ethernet−Howto
These boot time arguments can be made permanent so that you don't have to re−enter them every time.
Usually this is as simple as adding append="blah=123,456,789" to the top of your
/etc/lilo.conf file. See the LILO documentation for more details.
For more information on (and a complete list of) boot time arguments, please see the BootPrompt−HOWTO
ether=IRQ,BASE_ADDR,PARAM_1,PARAM_2,NAME
All arguments are optional. The first non−numeric argument is taken as the NAME.
IRQ: Obvious. An IRQ value of `0' (usually the default) means to autoIRQ. It's a historical accident that the
IRQ setting is first rather than the base_addr −− this will be fixed whenever something else changes.
BASE_ADDR: Also obvious. A value of `0' (usually the default) means to probe a card−type−specific
address list for an ethercard.
PARAM_1: It was orginally used as an override value for the memory start for a shared−memory ethercard,
like the WD80*3. Some drivers use the low four bits of this value to set the debug message level. 0 −−
default, 1−7 −− level 1..7, (7 is maximum verbosity) 8 −− level 0 (no messages). Also, the LANCE driver
uses the low four bits of this value to select the DMA channel. Otherwise it uses auto−DMA.
PARAM_2: The 3c503 driver uses this to select between the internal and external transceivers. 0 −−
default/internal, 1 −− AUI external. The Cabletron E21XX card also uses the low 4 bits of PARAM_2 to
select the output media. Otherwise it detects automatically.
NAME: Selects the network device the values refer to. The standard kernel uses the names `eth0', `eth1',
`eth2' and `eth3' for bus−attached ethercards, and `atp0' for the parallel port `pocket' ethernet adaptor. The
arcnet driver uses `arc0' as its name. The default setting is for a single ethercard to be probed for as `eth0'.
Multiple cards can only be enabled by explicitly setting up their base address using these LILO parameters.
The 1.0 kernel has LANCE−based ethercards as a special case. LILO arguments are ignored, and LANCE
cards are always assigned `eth<n>' names starting at `eth0'. Additional non−LANCE ethercards must be
explicitly assigned to `eth<n+1>', and the usual `eth0' probe disabled with something like `ether=0,−1,eth0'. (
Yes, this is bug. )
reserve=IO−base,extent{,IO−base,extent...}
In some machines it may be necessary to prevent device drivers from checking for devices (auto−probing) in a
specific region. This may be because of poorly designed hardware that causes the boot to freeze (such as some
ethercards), hardware that is mistakenly identified, hardware whose state is changed by an earlier probe, or
The reserve boot−time argument addresses this problem by specifying an I/O port region that shouldn't be
probed. That region is reserved in the kernel's port registration table as if a device has already been found in
that region. Note that this mechanism shouldn't be necessary on most machines. Only when there is a problem
or special case would it be necessary to use this.
The I/O ports in the specified region are protected against device probes. This was put in to be used when
some driver was hanging on a NE2000, or misidentifying some other device as its own. A correct device
driver shouldn't probe a reserved region, unless another boot argument explicitly specifies that it do so. This
implies that reserve will most often be used with some other boot argument. Hence if you specify a
reserve region to protect a specific device, you must generally specify an explicit probe for that device.
Most drivers ignore the port registration table if they are given an explicit address.
keeps all device drivers except the ethercard drivers from probing 0x300−0x31f.
As usual with boot−time specifiers there is an 11 parameter limit, thus you can only specify 5 reserved regions
per reserve keyword. Multiple reserve specifiers will work if you have an unusually complicated
request.
Your particular distribution may offer nice graphical configuration tools for setting up ethernet modules. If
possible you should try and use them first. The description that follows here gives information on what
underlies any fancy configuration program, and what these programs change.
The information that controls what modules are to be used and what options are supplied to each module is
usually stored in the file /etc/modules.conf. The two main options of interest (for ethernet cards) that
will be used in this file are alias and options. The modprobe command consults this file for module
information.
The actual modules themselves are typically stored in a directory named /lib/modules/`uname
−r`/net where the uname −r command gives the kernel version (e.g. 2.0.34). You can look in there to see
which module matches your card.
The first thing you need in your modules.conf file is something to tell modprobe what driver to use for
the eth0 (and eth1 and...) network interface. You use the alias command for this. For example, if you
have an ISA SMC EtherEZ card which uses the smc−ultra.o driver module, you need to alias this
driver to eth0 by adding the line:
The other thing you may need is an options line indicating what options are to be used with a particular
module (or module alias). Continuing with the above example, if you only used the single alias line with no
options line, the kernel would warn you (see dmesg) that autoprobing for ISA cards is not a good idea. To
get rid of this warning, you would add another line telling the module what I/O base the card is configured to,
in this case say the hexidecimal address 0x280 for example.
Most ISA modules accept parameters like io=0x340 and irq=12 on the insmod command line. It is
REQUIRED or at least STRONGLY ADVISED that you supply these parameters to avoid probing for the card.
Unlike PCI and EISA devices, there is no real safe way to do auto−probing for most ISA devices, and so it
should be avoided when using drivers as modules.
A list of all the options that each module accepts can be found in the file:
/usr/src/linux/Documentation/networking/net−modules.txt
It is recommended that you read that to find out what options you can use for your particular card. Note that
some modules support comma separated value lists for modules that have the capability to handle multiple
devices from a single module, such as all the 8390 based drivers, and the PLIP driver. For exmple:
The above would have the one module controlling four 3c503 cards, with card 2 and 4 using external
transcievers. Don't put spaces around the `=' or commas.
Also note that a busy module can't be removed. That means that you will have to ifconfig eth0 down
(shut down the ethernet card) before you can remove the module(s).
The command lsmod will show you what modules are loaded, whether they are in use, and rmmod will
remove them.
For those looking for information that is not specific in any way to Linux (i.e. what is 10BaseT, what is AUI,
what does a hub do, etc.) I strongly recommend making use of the newsgroup comp.dcom.lans.ethernet and/or
comp.sys.ibm.pc.hardware.networking. Newsgroup archives such as those at dejanews.com can also be an
invaluable source of information. You can grab the newsgroup FAQ from RTFM (which holds all the
newsgroup FAQs) at the following URL:
Usenet FAQs
You can also have a look at the `Ethernet−HomePage' so to speak, which is at the following URL:
Ethernet−HomePage
This document is Copyright (c) 1993−2000 by Paul Gortmaker. Permission is granted to make and distribute
verbatim copies of this manual provided the copyright notice and this permission notice are preserved on all
copies.
Permission is granted to copy and distribute modified versions of this document under the conditions for
verbatim copying, provided that this copyright notice is included exactly as in the original, and that the entire
resulting derived work is distributed under the terms of a permission notice identical to this one.
Permission is granted to copy and distribute translations of this document into another language, under the
above conditions for modified versions.
A hint to people considering doing a translation. First, translate the SGML source (available via FTP from the
HowTo main site) so that you can then generate other output formats. Be sure to keep a copy of the original
English SGML source that you translated from! When an updated HowTo is released, get the new SGML
source for that version, and then a simple diff −u old.sgml new.sgml will show you exactly what
has changed so that you can easily incorporate those changes into your translated SMGL source without
having to re−read or re−translate everything.
If you are intending to incorporate this document into a published work, please make contact (via e−mail) so
that you can be supplied with the most up to date information available. In the past, out of date versions of the
Linux HowTo documents have been published, which caused the developers undue grief from being plagued
with questions that were already answered in the up to date versions.
8.6 Closing
In the early days of linux, some ten(!) years ago, there were not a lot of drivers and not a lot of users. I had the
time to follow individual driver developments, read about common problems in newsgroups, and answer
posted and e−mailed questions. Things are a lot different now. There are a huge number of drivers, and a huge
number of users too, and there is no way I can keep up with each new development! This is where I need your
help. If you have found a new driver that isn't mentioned here, or any glaring typos, or outdated info in this
document, please send an e−mail. It is big, and it is easy to overlook stuff. If you have e−mailed about a
change, and it hasn't been included in the next version, please don't hesitate to send it again, as it might have
got lost amongst the usual sea of SPAM and junk mail I get.
Thanks!