ULR -TC582524000004736F TEST REPORT

Report No. : PN:EE:1556004744 ISSUE DATE : 03/10/2024

*1556004744*
CABTECH INTERNATIONAL
PHASE -3,SHED NO 3027,G I D C, DARED,
JAMNAGAR-GUJARAT-361004
INDIA

CONTACT PERSON : MR.BIRJU JOTWANI

THE FOLLOWING SAMPLE(S) WAS/WERE SUBMITTED AND IDENTIFIED BY/ON BEHALF OF THE CUSTOMER AS :
DISCIPLINE Chemical
GROUP Hazardous & Restricted Chemicals
SAMPLE DESCRIPTION PLASTIC RING ( NYLON 66 )
OEM OTHERS
COUNTRY OF ORIGIN INDIA
DATE OF SAMPLE REGISTRATION 23/09/2024 TESTING PERIOD : 23/09/2024 – 26/09/2024
TEST(S) REQUESTED ROHS 10E

Test requested: Selected test (s) as requested by the client.

Test method(s): Please refer to next page(s).
Test results(s): Please refer to next page(s).
Test Request Conclusion
EU RoHS Directive (EU) 2015/863 amending Annex II to Directive 2011/65/EU - Lead, Mercury,
Cadmium, Hexavalent chromium, Polybrominated biphenyls (PBB), Polybrominated diphenyl ethers
PASS
(PBDE), Bis(2-ethylhexyl) phthalate (DEHP), Butyl benzyl phthalate (BBP), Dibutyl phthalate (DBP)
and Diisobutyl phthalate (DIBP)

Conclusion:Based on the performed tests on selected part of submitted sample(s), the results of Cadmium, Lead, Mercury,
Hexavalent chromium, Polybrominated biphenyls (PBBs), Polybrominated diphenyl ethers (PBDEs) and
Phthalates such as Bis(2-ethylhexyl) phthalate (DEHP), Butyl benzyl phthalate (BBP), Dibutyl phthalate (DBP)
and Di isobutyl phthalate (DIBP) comply with the limits as set by RoHS Directive (EU) 2015/863 amending
Annex II to Directive 2011/65/EU.

Per Pro SGS India Private Ltd

SACHIN M. VIBHUTE
Sr.Executive
Authorized Signatory
Email your Test Report Related Enquiries at [email protected]

JOE No. : 2456801130 Page -1 of 8 Control No.:1556504200

“This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at
http://www.sgsgroup.in/Service-Terms and, for electronic format documents, subject to Terms and Conditions for Electronic Documents a www.sgs.com/terms_e-
document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that
information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole
responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents.
This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or
appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. The laboratory shall be responsible for all the information provided
in the report, except when information and instruction for specific scope of testing is provided by the customer.”
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days from the date of issue of report
The samples from the regulatory bodies are to be retained as specified. This document cannot be reproduced, except in full, without prior written approval of the company.
Statement of conformity is based on comparison of measurement result(s) with the applicable limit(s) according to the specification in the respective standard or as shared by the
customer. Measurement Uncertainty is not taken into account unless otherwise requested in writing.

Transportation Laboratory, Gat No. : 239/1/3, Village Khalumbre, Tal. Khed, Dist- Pune, Chakan – 410501, Maharashtra, India,
SGS India Private Ltd Phone: +91 2135 615300, Fax: +91 2135 615333 www.sgs.com
Member of the SGS Group (SGS SA)
 ULR -TC582524000004736F TEST REPORT
Report No. : PN:EE:1556004744 ISSUE DATE : 03/10/2024
*1556004744*
Test results:

Test Part Description:

Specimen No. SGS Sample ID DESCRIPTION

1 - PLASTIC RING ( NYLON 66 )

Notes:
(1) The maximum permissible limit is quoted from RoHS Directive (EU) 2015/863.
(2) IEC 62321 series is equivalent to EN 62321 series.
(3) The restriction of DEHP, BBP, DBP and DIBP shall apply to medical devices, including in vitro medical devices, and
monitoring and control instruments, including industrial monitoring and control instruments, from 22 July 2021

JOE No. : 2456801130 Page -2 of 8 Control No.:1556504200

“This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at
http://www.sgsgroup.in/Service-Terms and, for electronic format documents, subject to Terms and Conditions for Electronic Documents a www.sgs.com/terms_e-
document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that
information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole
responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents.
This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or
appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. The laboratory shall be responsible for all the information provided
in the report, except when information and instruction for specific scope of testing is provided by the customer.”
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days from the date of issue of report
The samples from the regulatory bodies are to be retained as specified. This document cannot be reproduced, except in full, without prior written approval of the company.
Statement of conformity is based on comparison of measurement result(s) with the applicable limit(s) according to the specification in the respective standard or as shared by the
customer. Measurement Uncertainty is not taken into account unless otherwise requested in writing.

Transportation Laboratory, Gat No. : 239/1/3, Village Khalumbre, Tal. Khed, Dist- Pune, Chakan – 410501, Maharashtra, India,
SGS India Private Ltd Phone: +91 2135 615300, Fax: +91 2135 615333 www.sgs.com
Member of the SGS Group (SGS SA)
 ULR -TC582524000004736F TEST REPORT
Report No. : PN:EE:1556004744 ISSUE DATE : 03/10/2024
*1556004744*
EU RoHS Directive (EU) 2015/863 amending Annex II to Directive 2011/65/EU - Lead, Mercury, Cadmium, Hexavalent
chromium, Polybrominated biphenyls (PBB), Polybrominated diphenyl ethers (PBDE), Bis(2-ethylhexyl) phthalate
(DEHP), Butyl benzyl phthalate (BBP), Dibutyl phthalate (DBP) and Diisobutyl phthalate (DIBP)
Test Method: With reference to IEC 62321-4:2013+AMD1:2017, IEC 62321-5:2013, IEC 62321-7-2:2017,
IEC 62321-6:2015 and IEC 62321-8:2017, analysis was performed by ICP-OES, UV-Vis and GC-MS.

Test Item(s) Limit Unit(s) MDL Result

Lead (Pb) 1000 mg/kg 5 n.d.
Mercury (Hg) 1000 mg/kg 5 n.d.
Cadmium (Cd) 100 mg/kg 5 n.d.
Hexavalent Chromium (Cr(VI)) 1000 mg/kg 8 n.d.
Polybrominated biphenyls (PBB) 1000 mg/kg - n.d.
Monobrominated biphenyl (MonoBB) - mg/kg 50 n.d.
Dibrominated biphenyl (DiBB) - mg/kg 50 n.d.
Tribrominated biphenyl (TriBB) - mg/kg 50 n.d.
Tetrabrominated biphenyl (TetraBB) - mg/kg 50 n.d.
Pentabrominated biphenyl (PentaBB) - mg/kg 50 n.d.
Hexabrominated biphenyl (HexaBB) - mg/kg 50 n.d.
Heptabrominated biphenyl (HeptaBB) - mg/kg 50 n.d.
Octabrominated biphenyl (OctaBB) - mg/kg 50 n.d.
Nonabrominated biphenyl (NonaBB) - mg/kg 50 n.d.
Decabrominated biphenyl (DecaBB) - mg/kg 50 n.d.
Polybrominated diphenyl ethers (PBDE) 1000 mg/kg - n.d.
Monobrominated diphenyl ether (MonoBDE) - mg/kg 50 n.d.
Dibrominated diphenyl ether (DiBDE) - mg/kg 50 n.d.
Tribrominated diphenyl ether (TriBDE) - mg/kg 50 n.d.
Tetrabrominated diphenyl ether (TetraBDE) - mg/kg 50 n.d.
Pentabrominated diphenyl ether (PentaBDE) - mg/kg 50 n.d.
Hexabrominated diphenyl ether (HexaBDE) - mg/kg 50 n.d.
Heptabrominated diphenyl ether (HeptaBDE) - mg/kg 50 n.d.
Octabrominated diphenyl ether (OctaBDE) - mg/kg 50 n.d.
Nonabrominated diphenyl ether (NonaBDE) - mg/kg 50 n.d.
Decabrominated diphenyl ether (DecaBDE) - mg/kg 50 n.d.
Bis(2-ethylhexyl) phthalate (DEHP) 1000 mg/kg 100 n.d.
Butyl benzyl phthalate (BBP) 1000 mg/kg 100 n.d.
Dibutyl phthalate (DBP) 1000 mg/kg 100 n.d.
Diisobutyl phthalate (DIBP) 1000 mg/kg 100 n.d.

Remarks:
(1) 1mg/kg=0.0001%
(2) MDL = Method Detection Limit
(3) ND = Not Detected (<MDL)
(4) “-” = Not Regulated
JOE No. : 2456801130 Page -3 of 8 Control No.:1556504200
“This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at
http://www.sgsgroup.in/Service-Terms and, for electronic format documents, subject to Terms and Conditions for Electronic Documents a www.sgs.com/terms_e-
document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that
information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole
responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents.
This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or
appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. The laboratory shall be responsible for all the information provided
in the report, except when information and instruction for specific scope of testing is provided by the customer.”
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days from the date of issue of report
The samples from the regulatory bodies are to be retained as specified. This document cannot be reproduced, except in full, without prior written approval of the company.
Statement of conformity is based on comparison of measurement result(s) with the applicable limit(s) according to the specification in the respective standard or as shared by the
customer. Measurement Uncertainty is not taken into account unless otherwise requested in writing.

Transportation Laboratory, Gat No. : 239/1/3, Village Khalumbre, Tal. Khed, Dist- Pune, Chakan – 410501, Maharashtra, India,
SGS India Private Ltd Phone: +91 2135 615300, Fax: +91 2135 615333 www.sgs.com
Member of the SGS Group (SGS SA)
 ULR -TC582524000004736F TEST REPORT
Report No. : PN:EE:1556004744 ISSUE DATE : 03/10/2024
*1556004744*
Process Flow for analysis of metal contents in plastics, metals, and electronic components sample

Sample preparation,
0.10 – 0.3 g

Microwave Digestion NO YES Microwave Digestion

System Si- based System
10 ml conc. HNO3 sample 10 ml HNO3 + 0.5 ml HF

Cool down
Cool down
Add 0.25 g
orthoboric acid

Filtration

Final volume makeup

ICP-OES

Tested By: Tanvi Tasedar Checked By: Sachin Vibhute

Chemist Sr. Executive

JOE No. : 2456801130 Page -4 of 8 Control No.:1556504200

“This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at
http://www.sgsgroup.in/Service-Terms and, for electronic format documents, subject to Terms and Conditions for Electronic Documents a www.sgs.com/terms_e-
document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that
information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole
responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents.
This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or
appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. The laboratory shall be responsible for all the information provided
in the report, except when information and instruction for specific scope of testing is provided by the customer.”
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days from the date of issue of report
The samples from the regulatory bodies are to be retained as specified. This document cannot be reproduced, except in full, without prior written approval of the company.
Statement of conformity is based on comparison of measurement result(s) with the applicable limit(s) according to the specification in the respective standard or as shared by the
customer. Measurement Uncertainty is not taken into account unless otherwise requested in writing.

Transportation Laboratory, Gat No. : 239/1/3, Village Khalumbre, Tal. Khed, Dist- Pune, Chakan – 410501, Maharashtra, India,
SGS India Private Ltd Phone: +91 2135 615300, Fax: +91 2135 615333 www.sgs.com
Member of the SGS Group (SGS SA)
 ULR -TC582524000004736F TEST REPORT
Report No. : PN:EE:1556004744 ISSUE DATE : 03/10/2024
*1556004744*
Process Flow for analysis of Flame Retardants in plastics, metals and electronic components sample

Sample

Sample Pretreatment

Soxhlet extraction
USEPA 3540C/3550/IEC
62321-6:2015

Concentrate/Dilute
Extracted solution.

Filter if necessary

On High Mass Range GCMS-

Sample Analyzed

Tested By: Ashwini Sagar Checked By: Sachin Vibhute

Executive Sr. Executive

JOE No. : 2456801130 Page -5 of 8 Control No.:1556504200

“This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at
http://www.sgsgroup.in/Service-Terms and, for electronic format documents, subject to Terms and Conditions for Electronic Documents a www.sgs.com/terms_e-
document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that
information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole
responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents.
This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or
appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. The laboratory shall be responsible for all the information provided
in the report, except when information and instruction for specific scope of testing is provided by the customer.”
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days from the date of issue of report
The samples from the regulatory bodies are to be retained as specified. This document cannot be reproduced, except in full, without prior written approval of the company.
Statement of conformity is based on comparison of measurement result(s) with the applicable limit(s) according to the specification in the respective standard or as shared by the
customer. Measurement Uncertainty is not taken into account unless otherwise requested in writing.

Transportation Laboratory, Gat No. : 239/1/3, Village Khalumbre, Tal. Khed, Dist- Pune, Chakan – 410501, Maharashtra, India,
SGS India Private Ltd Phone: +91 2135 615300, Fax: +91 2135 615333 www.sgs.com
Member of the SGS Group (SGS SA)
 ULR -TC582524000004736F TEST REPORT
Report No. : PN:EE:1556004744 ISSUE DATE : 03/10/2024
*1556004744*
Process Flow for analysis of Hexavalent Chromium contents in Plastics and electronic components sample

Sample

Non-Metallic Sample
retreatment

For solvent soluble polymers For insoluble/unknown polymer

(ABS, PC & PVC) & electronics without Sb

Add NMP solvent for dissolution Added mixture of Toluene and

followed by addition of digestion digestion solution
solution.

Dissolve polymer by Microwave digestion at 150°C

Ultrasonication at 60°C for 1hr for 1.5hr

Adjust the pH using Nitric acid. Add 1,5-

diphenylcarbazide for color development.

Analysis on UV-Vis
Spectrophotometer

Data

Tested By: Mangal Tambe Checked By: Sachin Vibhute

Chemist Sr. Executive

JOE No. : 2456801130 Page -6 of 8 Control No.:1556504200

“This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at
http://www.sgsgroup.in/Service-Terms and, for electronic format documents, subject to Terms and Conditions for Electronic Documents a www.sgs.com/terms_e-
document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that
information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole
responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents.
This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or
appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. The laboratory shall be responsible for all the information provided
in the report, except when information and instruction for specific scope of testing is provided by the customer.”
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days from the date of issue of report
The samples from the regulatory bodies are to be retained as specified. This document cannot be reproduced, except in full, without prior written approval of the company.
Statement of conformity is based on comparison of measurement result(s) with the applicable limit(s) according to the specification in the respective standard or as shared by the
customer. Measurement Uncertainty is not taken into account unless otherwise requested in writing.

Transportation Laboratory, Gat No. : 239/1/3, Village Khalumbre, Tal. Khed, Dist- Pune, Chakan – 410501, Maharashtra, India,
SGS India Private Ltd Phone: +91 2135 615300, Fax: +91 2135 615333 www.sgs.com
Member of the SGS Group (SGS SA)
 ULR -TC582524000004736F TEST REPORT
Report No. : PN:EE:1556004744 ISSUE DATE : 03/10/2024
*1556004744*
Process Flow for analysis of Phthalates in Electrotechnical Product As per Soxhlet Extraction or THF
Extraction

Sample

Non soluble Soluble sample

sample Pretreatment

Sample Pretreatment
Sample Pretreatment

Addition THF

Soxhlet extraction with n-

hexane IEC 62321-8:2017
Sonication at ultrasonic bath for
IEC 62321-8:2017 30 to 60 min

Concentrate/Dilute
Extracted solution Addition of Acetonitrile

Filter if necessary
Filter if necessary

On GCMS-Sample Analyzed
On GCMS-Sample Analyzed

Data

Tested By: Shubhangi Bhote Checked By: Sachin Vibhute

Chemist Sr. Executive
JOE No. : 2456801130 Page -7 of 8 Control No.:1556504200
“This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at
http://www.sgsgroup.in/Service-Terms and, for electronic format documents, subject to Terms and Conditions for Electronic Documents a www.sgs.com/terms_e-
document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that
information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole
responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents.
This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or
appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. The laboratory shall be responsible for all the information provided
in the report, except when information and instruction for specific scope of testing is provided by the customer.”
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days from the date of issue of report
The samples from the regulatory bodies are to be retained as specified. This document cannot be reproduced, except in full, without prior written approval of the company.
Statement of conformity is based on comparison of measurement result(s) with the applicable limit(s) according to the specification in the respective standard or as shared by the
customer. Measurement Uncertainty is not taken into account unless otherwise requested in writing.

Transportation Laboratory, Gat No. : 239/1/3, Village Khalumbre, Tal. Khed, Dist- Pune, Chakan – 410501, Maharashtra, India,
SGS India Private Ltd Phone: +91 2135 615300, Fax: +91 2135 615333 www.sgs.com
Member of the SGS Group (SGS SA)
 ULR -TC582524000004736F TEST REPORT
Report No. : PN:EE:1556004744 ISSUE DATE : 03/10/2024
*1556004744*

Sample Photo:

Report No.:1556004744

SGS authenticate the photo on original report only

*** End of Report ***

JOE No. : 2456801130 Page -8 of 8 Control No.:1556504200

“This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at
http://www.sgsgroup.in/Service-Terms and, for electronic format documents, subject to Terms and Conditions for Electronic Documents a www.sgs.com/terms_e-
document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that
information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole
responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents.
This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or
appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. The laboratory shall be responsible for all the information provided
in the report, except when information and instruction for specific scope of testing is provided by the customer.”
Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days from the date of issue of report
The samples from the regulatory bodies are to be retained as specified. This document cannot be reproduced, except in full, without prior written approval of the company.
Statement of conformity is based on comparison of measurement result(s) with the applicable limit(s) according to the specification in the respective standard or as shared by the
customer. Measurement Uncertainty is not taken into account unless otherwise requested in writing.

Transportation Laboratory, Gat No. : 239/1/3, Village Khalumbre, Tal. Khed, Dist- Pune, Chakan – 410501, Maharashtra, India,
SGS India Private Ltd Phone: +91 2135 615300, Fax: +91 2135 615333 www.sgs.com
Member of the SGS Group (SGS SA)