@A318/A319/A320/A321

SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
Tel : (33) 5 61 93 33 33
Telex : AIRBU 530526F
Fax : (33) 5 61 93 42 51

ATA SYSTEM: 52

TITLE: DOORS - MAIN GEAR DOORS - INTRODUCE NEW FAIRING

ATTACHMENT STUD ASSEMBLIES
MODIFICATION No.: 155648J3676
This page transmits Revision No.03 of Service Bulletin No.A320-52-1165

ADDITIONAL WORK

**CONF ALL

Additional Work 1 is required by this revision for aircraft concerned by Configurations 001, 002, 004,
005, 007 to 015, 017 and 018 of this revision and modified by the original issue of this Service Bulletin.

Additional Work 2 is required by this revision for aircraft concerned by Configuration 016 of this revision
and modified by the original issue or the Revision No. 01 of this Service Bulletin, or reidentified by the
Additional Work from Revision No. 01.

Additional Work 3 is required by this revision for aircraft concerned by Configurations 003 and 006 of
this revision and modified by the Revision No. 02 or any previous issue of this Service Bulletin, or
reidentified by the Additional Work from Revision No. 01 or Revision No. 02.

Unless otherwise stated by an Airworthiness Directive, AIRBUS recommends the additional work to be
accomplished within one year after the issue of this revision.

Additional Works 1, 2 and 3 are necessary to correct the re-identification of the Main Landing Gear
(MLG) fixed fairings assemblies.

REASON

Revision No. 03 issued to correct the re-identification of the fairings for aircraft concerned by
Configurations 003 and 006. Also this Revision adds corrections in the Accomplishment Instructions.
Re-identification in accordance with Additional Works 1, 2 and 3 is required in order to consider the
mandatory repetitive inspections as per Service Bulletin No. A320-52-1163 as terminated.

CHANGES

The main changes of this revision are:

- ’GENERAL EVALUATION TABLE’ updated: ’JACKING’ updated to ’NORMAL JACKING’

- Aircraft operators updated

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 1

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

- Effectivity updated, scrapped MSNs removed

- Accomplishment Timescale added for Additional Works 1, 2 and 3

- Procurement address updated

- Reidentified parts matset REIDB04 updated and REIDB11 deleted

- New sentences added in ’ACCOMPLISHMENT INSTRUCTIONS’ paragraph

- ’PROCEDURE’ paragraph updated for Configurations 003 and 006 to correct the re-identification of
the fairing

- ’PROCEDURE’ paragraph updated to delete the removal/installation of Items (37) and (38) from the
MLG leg

- ’PROCEDURE’ paragraph updated for Configurations 009, 010 and 019 to replace ’stud, Item (6)’
by ’stud, Item (5)’

- Views A, B and C clarified and other views moved in Figures A-UBBAA, A-UBBAB, A-UBBAC and
A-UBBAD

- Configurations 003, 006 and 016 deleted from Additional Work 1

- Additional Work 2 created for Configuration 016

- Additional Work 3 created for Configurations 003 and 006

- Layout of Appendix 01 and Appendix 02 updated.

FRONT MATTER
DOORS - MAIN GEAR DOORS - CONFIGURATION UPDATED R
INTRODUCE NEW FAIRING
ATTACHMENT STUD ASSEMBLIES
SUMMARY
GENERAL EVALUATION GENERAL EVALUATION TABLE UPDATED R
EFFECTIVITY OPERATOR LIST UPDATED R
MANPOWER MANPOWER UPDATED R
MANPOWER UPDATED R
MANPOWER UPDATED R
MANPOWER UPDATED R
MANPOWER UPDATED R
MANPOWER UPDATED R
MANPOWER UPDATED R
MANPOWER UPDATED R
MANPOWER UPDATED R
MANPOWER UPDATED R
MANPOWER UPDATED R
MANPOWER UPDATED R
MANPOWER UPDATED R

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 2

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

MANPOWER UPDATED R
MANPOWER UPDATED R
MANPOWER UPDATED R
MANPOWER UPDATED R
MANPOWER UPDATED R
APPENDICES APPENDICES UPDATED R
PLANNING INFORMATION
EFFECTIVITY EFFECTIVITY RELATED INFORMATION R
UPDATED
Configuration definition
CONF 001 CONFIGURATION DEFINITION UPDATED R
CONF 002 CONFIGURATION DEFINITION UPDATED R
CONF 003 CONFIGURATION DEFINITION UPDATED R
CONF 004 CONFIGURATION DEFINITION UPDATED R
CONF 006 CONFIGURATION DEFINITION UPDATED R
CONF 011 CONFIGURATION DEFINITION UPDATED R
CONF 013 CONFIGURATION DEFINITION UPDATED R
CONF 014 CONFIGURATION DEFINITION UPDATED R
CONF 015 CONFIGURATION DEFINITION UPDATED R
CONF 016 CONFIGURATION DEFINITION UPDATED R
CONF 017 CONFIGURATION DEFINITION UPDATED R
CONF 018 CONFIGURATION DEFINITION UPDATED R
CONF 020 CONFIGURATION DEFINITION UPDATED R
Material Effectivity MATERIAL EFFECTIVITY UPDATED R
MATERIAL SET UPDATED
COMPLIANCE
Accomplishment Timescale ACCOMPLISHMENT TIMESCALE UPDATED R
MANPOWER MANPOWER UPDATED R
MANPOWER UPDATED R
MANPOWER UPDATED R
MANPOWER UPDATED R
MANPOWER UPDATED R
CONFIGURATION UPDATED
MANPOWER UPDATED R
CONFIGURATION UPDATED
MANPOWER UPDATED R
CONFIGURATION UPDATED
MANPOWER UPDATED R
CONFIGURATION UPDATED
MANPOWER UPDATED R
CONFIGURATION UPDATED
MANPOWER UPDATED R
CONFIGURATION UPDATED
MANPOWER UPDATED R
CONFIGURATION UPDATED
MANPOWER UPDATED R
CONFIGURATION UPDATED

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 3

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

MANPOWER UPDATED R
CONFIGURATION UPDATED
MANPOWER UPDATED R
CONFIGURATION UPDATED
MANPOWER UPDATED R
CONFIGURATION UPDATED
MANPOWER UPDATED R
CONFIGURATION UPDATED
MANPOWER UPDATED R
CONFIGURATION UPDATED
MANPOWER UPDATED R
CONFIGURATION UPDATED
MANPOWER UPDATED R
CONFIGURATION UPDATED
MANPOWER UPDATED R
CONFIGURATION UPDATED
REFERENCES REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
REFERENCED DOCUMENTATION UPDATED R
INTERCHANGEABILITY/MIXABILITY INTERCHANGEABILITY/MIXABILITY UPDATED R
INTERCHANGEABILITY/MIXABILITY UPDATED R
INTERCHANGEABILITY/MIXABILITY UPDATED R
INTERCHANGEABILITY/MIXABILITY UPDATED R
INTERCHANGEABILITY/MIXABILITY UPDATED R
INTERCHANGEABILITY/MIXABILITY UPDATED R
INTERCHANGEABILITY/MIXABILITY UPDATED R
INTERCHANGEABILITY/MIXABILITY UPDATED R
INTERCHANGEABILITY/MIXABILITY UPDATED R
INTERCHANGEABILITY/MIXABILITY UPDATED R
INTERCHANGEABILITY/MIXABILITY UPDATED R

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 4

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

INTERCHANGEABILITY/MIXABILITY UPDATED R
INTERCHANGEABILITY/MIXABILITY UPDATED R
INTERCHANGEABILITY/MIXABILITY UPDATED R
INTERCHANGEABILITY/MIXABILITY UPDATED R
INTERCHANGEABILITY/MIXABILITY UPDATED R
INTERCHANGEABILITY/MIXABILITY UPDATED R
INTERCHANGEABILITY/MIXABILITY UPDATED R
INTERCHANGEABILITY/MIXABILITY UPDATED R
INTERCHANGEABILITY/MIXABILITY UPDATED R
MATERIAL INFORMATION
MATERIAL - PRICE AND AVAILABILITY
Procurement Addresses PROCUREMENT ADDRESSES UPDATED R
INDUSTRY SUPPORT INFORMATION INDUSTRY SUPPORT INFORMATION UPDATED R
LIST OF COMPONENTS
Kit 521165B03R00 PART MATERIAL SET UPDATED R
LIST OF MATERIALS - OPERATOR
SUPPLIED
Consumable Materials
Consumable CMLB02 CONSUMABLE MATERIAL SET UPDATED R
PARTS TO BE RE-IDENTIFIED BY PARTS TO BE RE-IDENTIFIED BY OPERATOR R
OPERATOR UPDATED
Reidentified part set REIDB04 PART MATERIAL SET UPDATED R
KEYWORD UPDATED
ITEM NUMBER UPDATED
PART NUMBER UPDATED
QUANTITY UPDATED
Reidentified part set REIDB11 PART MATERIAL SET DELETED D
ACCOMPLISHMENT INSTRUCTIONS
TASK 521165- 831-895-001-Modification TASK SOLUTION UPDATED R
NOTE UPDATED
CAUTION UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
REFERENCED DOCUMENTATION UPDATED
FIGURE REFERENCE UPDATED
NOTE UPDATED
Subtask 521165-020-403-001 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
REFERENCED DOCUMENTATION UPDATED
FIGURE REFERENCE UPDATED
NOTE UPDATED
Subtask 521165-960-401-001 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-001 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 5

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

Subtask 521165-420-401-001 SUBTASK SOLUTION UPDATED R

REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-420-402-001 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-403-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-402-002 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-020-403-002 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-960-401-002 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-002 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-002 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-420-402-002 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-403-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-402-003 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-020-403-003 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-960-401-004 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-003 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-003 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 6

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

Subtask 521165-420-402-003 SUBTASK SOLUTION UPDATED R

REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-930-401-003 SUBTASK SOLUTION UPDATED R
KEYWORD UPDATED
ITEM NUMBER UPDATED
PART NUMBER UPDATED
PART NUMBER DESCRIPTION UPDATED
QUANTITY UPDATED
MATERIAL LIST UPDATED
Subtask 521165-930-402-003 SUBTASK SOLUTION UPDATED R
KEYWORD UPDATED
ITEM NUMBER UPDATED
PART NUMBER UPDATED
PART NUMBER DESCRIPTION UPDATED
QUANTITY UPDATED
MATERIAL LIST UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
REFERENCED DOCUMENTATION UPDATED
FIGURE REFERENCE UPDATED
NOTE UPDATED
Subtask 521165-020-403-001 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
REFERENCED DOCUMENTATION UPDATED
FIGURE REFERENCE UPDATED
NOTE UPDATED
Subtask 521165-960-401-001 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-001 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-001 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-420-402-001 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
REFERENCED DOCUMENTATION UPDATED
FIGURE REFERENCE UPDATED
NOTE UPDATED

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 7

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

Subtask 521165-020-403-001 SUBTASK SOLUTION UPDATED R

CONFIGURATION UPDATED
REFERENCED DOCUMENTATION UPDATED
FIGURE REFERENCE UPDATED
NOTE UPDATED
Subtask 521165-960-401-001 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-001 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-001 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-420-402-001 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-403-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-402-004 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-020-403-004 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-960-401-005 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-004 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-004 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-420-402-004 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-930-401-004 SUBTASK SOLUTION UPDATED R
KEYWORD UPDATED
ITEM NUMBER UPDATED
PART NUMBER UPDATED
PART NUMBER DESCRIPTION UPDATED
QUANTITY UPDATED
MATERIAL LIST UPDATED

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 8

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

Subtask 521165-930-402-004 SUBTASK SOLUTION UPDATED R

KEYWORD UPDATED
ITEM NUMBER UPDATED
PART NUMBER UPDATED
PART NUMBER DESCRIPTION UPDATED
QUANTITY UPDATED
MATERIAL LIST UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-403-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-402-003 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-020-403-003 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-960-401-004 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-003 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-003 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-420-402-003 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-403-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-402-002 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-020-403-002 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-960-401-002 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-002 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-002 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 9

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

Subtask 521165-420-402-002 SUBTASK SOLUTION UPDATED R

REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-403-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-402-004 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-020-403-004 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-960-401-005 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-004 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-004 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-420-402-004 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-403-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-402-004 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-020-403-004 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-960-401-005 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-004 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-004 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-420-402-004 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION ADDED N

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 10

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

Subtask 521165-020-403-001 SUBTASK SOLUTION ADDED N

Subtask 521165-020-402-004 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-020-403-004 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-960-401-005 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-004 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-004 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-420-402-004 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-403-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-402-002 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-020-403-002 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-960-401-002 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-002 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-002 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-420-402-002 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-403-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-402-002 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-020-403-002 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 11

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

Subtask 521165-960-401-002 SUBTASK SOLUTION UPDATED R

CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-002 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-002 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-420-402-002 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
REFERENCED DOCUMENTATION UPDATED
FIGURE REFERENCE UPDATED
NOTE UPDATED
Subtask 521165-020-403-001 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
REFERENCED DOCUMENTATION UPDATED
FIGURE REFERENCE UPDATED
NOTE UPDATED
Subtask 521165-960-401-001 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-001 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-001 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-420-402-001 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
REFERENCED DOCUMENTATION UPDATED
FIGURE REFERENCE UPDATED
NOTE UPDATED

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 12

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

Subtask 521165-020-403-001 SUBTASK SOLUTION UPDATED R

CONFIGURATION UPDATED
REFERENCED DOCUMENTATION UPDATED
FIGURE REFERENCE UPDATED
NOTE UPDATED
Subtask 521165-960-401-001 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-001 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-001 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-420-402-001 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-403-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-402-002 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-020-403-002 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-960-401-002 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-002 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-002 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-420-402-002 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-930-401-022 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-930-402-022 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-403-001 SUBTASK SOLUTION ADDED N

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 13

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

Subtask 521165-020-402-002 SUBTASK SOLUTION DELETED FOR D

APPLICABLE MSN
Subtask 521165-020-403-002 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-960-401-002 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-002 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-002 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-420-402-002 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-403-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-402-002 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-020-403-002 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-960-401-002 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-002 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-002 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-420-402-002 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-403-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-402-004 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-020-403-004 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 14

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

Subtask 521165-960-401-005 SUBTASK SOLUTION UPDATED R

CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-004 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-004 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-420-402-004 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-020-402-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-403-001 SUBTASK SOLUTION ADDED N
Subtask 521165-020-402-002 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-020-403-002 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-960-401-002 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-960-402-002 SUBTASK SOLUTION UPDATED R
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
Subtask 521165-420-401-002 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
Subtask 521165-420-402-002 SUBTASK SOLUTION UPDATED R
REFERENCED DOCUMENTATION UPDATED
CONFIGURATION UPDATED
FIGURE REFERENCE UPDATED
ITEM NUMBER UPDATED
TASK 521165- 831-896-001-Modification - TASK SOLUTION UPDATED R
Additional Work 1 for Aircraft Concerned TASK TITLE UPDATED
by Configurations 001, 002, 004, 005, 007 NOTE UPDATED
to 015, 017 and 018 of this Revision and CAUTION UPDATED
Modified by Revision No. 00
Task associated data - 003 ELAPSED TIME UPDATED R
MAN HOURS UPDATED
ZONE UPDATED
Task associated data - 006 ELAPSED TIME UPDATED R
MAN HOURS UPDATED
ZONE UPDATED

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 15

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

Task associated data - 016 ELAPSED TIME UPDATED R

MAN HOURS UPDATED
ZONE UPDATED
Subtask 521165-910-402-001 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-839-402-001 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-910-402-001 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-839-402-001 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-910-402-001 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-839-402-001 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-941-402-001 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-941-402-001 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-941-402-001 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-831-401-001 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-402-006 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-401-002 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-402-007 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-401-003 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-831-402-008 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-831-401-004 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-402-009 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-401-014 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-402-014 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-401-006 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-831-402-011 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-831-401-007 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-402-012 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 16

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

Subtask 521165-831-401-015 SUBTASK SOLUTION UPDATED R

MATERIAL LIST UPDATED
Subtask 521165-831-402-015 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-401-010 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-402-002 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-401-012 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-402-004 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-401-016 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-402-016 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-401-017 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-402-017 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-401-018 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-402-018 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-401-019 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-402-019 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-401-020 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-402-020 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-401-021 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-831-402-021 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-831-401-022 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-402-022 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-401-023 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-831-402-023 SUBTASK SOLUTION UPDATED R
MATERIAL LIST UPDATED
Subtask 521165-942-402-001 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN
Subtask 521165-942-402-001 SUBTASK SOLUTION DELETED FOR D
APPLICABLE MSN

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 17

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

Subtask 521165-942-402-001 SUBTASK SOLUTION DELETED FOR D

APPLICABLE MSN
TASK 521165- 831-897-001-Modification - TASK SOLUTION ADDED N
Additional Work 2 for Aircraft Concerned
by Configuration 016 of this Revision and
Modified by the Original Issue or Revision
No. 01, or Reidentified by the Additional
Work from Revision No. 01
Task associated data - 001 TASK ASSOCIATED DATA ADDED N
Task associated data - 002 TASK ASSOCIATED DATA ADDED N
Task associated data - 003 TASK ASSOCIATED DATA ADDED N
Task associated data - 004 TASK ASSOCIATED DATA ADDED N
Task associated data - 005 TASK ASSOCIATED DATA ADDED N
Task associated data - 006 TASK ASSOCIATED DATA ADDED N
Task associated data - 007 TASK ASSOCIATED DATA ADDED N
Task associated data - 008 TASK ASSOCIATED DATA ADDED N
Task associated data - 009 TASK ASSOCIATED DATA ADDED N
Task associated data - 010 TASK ASSOCIATED DATA ADDED N
Task associated data - 011 TASK ASSOCIATED DATA ADDED N
Task associated data - 012 TASK ASSOCIATED DATA ADDED N
Task associated data - 013 TASK ASSOCIATED DATA ADDED N
Task associated data - 014 TASK ASSOCIATED DATA ADDED N
Task associated data - 015 TASK ASSOCIATED DATA ADDED N
Task associated data - 016 TASK ASSOCIATED DATA ADDED N
Task associated data - 017 TASK ASSOCIATED DATA ADDED N
Task associated data - 018 TASK ASSOCIATED DATA ADDED N
Task associated data - 019 TASK ASSOCIATED DATA ADDED N
Task associated data - 020 TASK ASSOCIATED DATA ADDED N
Subtask 521165-910-403-001 SUBTASK SOLUTION ADDED N
Subtask 521165-839-403-001 SUBTASK SOLUTION ADDED N
Subtask 521165-941-403-001 SUBTASK SOLUTION ADDED N
Subtask 521165-930-403-003 SUBTASK SOLUTION ADDED N
Subtask 521165-930-406-001 SUBTASK SOLUTION ADDED N
Subtask 521165-942-403-001 SUBTASK SOLUTION ADDED N
TASK 521165- 831-898-001-Modification - TASK SOLUTION ADDED N
Additional Work 3 for Aircraft Concerned
by Configurations 003 and 006 of this
Revision and Modified by Revision No. 02
or any Previous Issue, or Reidentified by
the Additional Work from Revision No. 01
or Revision No. 02
Task associated data - 001 TASK ASSOCIATED DATA ADDED N
Task associated data - 002 TASK ASSOCIATED DATA ADDED N
Task associated data - 003 TASK ASSOCIATED DATA ADDED N
Task associated data - 004 TASK ASSOCIATED DATA ADDED N
Task associated data - 005 TASK ASSOCIATED DATA ADDED N
Task associated data - 006 TASK ASSOCIATED DATA ADDED N
Task associated data - 007 TASK ASSOCIATED DATA ADDED N

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 18

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

Task associated data - 008 TASK ASSOCIATED DATA ADDED N

Task associated data - 009 TASK ASSOCIATED DATA ADDED N
Task associated data - 010 TASK ASSOCIATED DATA ADDED N
Task associated data - 011 TASK ASSOCIATED DATA ADDED N
Task associated data - 012 TASK ASSOCIATED DATA ADDED N
Task associated data - 013 TASK ASSOCIATED DATA ADDED N
Task associated data - 014 TASK ASSOCIATED DATA ADDED N
Task associated data - 015 TASK ASSOCIATED DATA ADDED N
Task associated data - 016 TASK ASSOCIATED DATA ADDED N
Task associated data - 017 TASK ASSOCIATED DATA ADDED N
Task associated data - 018 TASK ASSOCIATED DATA ADDED N
Task associated data - 019 TASK ASSOCIATED DATA ADDED N
Task associated data - 020 TASK ASSOCIATED DATA ADDED N
Subtask 521165-910-404-001 SUBTASK SOLUTION ADDED N
Subtask 521165-839-404-001 SUBTASK SOLUTION ADDED N
Subtask 521165-910-404-001 SUBTASK SOLUTION ADDED N
Subtask 521165-839-404-001 SUBTASK SOLUTION ADDED N
Subtask 521165-941-404-001 SUBTASK SOLUTION ADDED N
Subtask 521165-941-404-001 SUBTASK SOLUTION ADDED N
Subtask 521165-930-405-001 SUBTASK SOLUTION ADDED N
Subtask 521165-930-407-001 SUBTASK SOLUTION ADDED N
Subtask 521165-930-405-002 SUBTASK SOLUTION ADDED N
Subtask 521165-930-407-002 SUBTASK SOLUTION ADDED N
Subtask 521165-942-404-001 SUBTASK SOLUTION ADDED N
Subtask 521165-942-404-001 SUBTASK SOLUTION ADDED N
Fig. A-UBBAA FIGURE SOLUTION UPDATED R
Fig. A-UBBAA Sheet 01 SHEET UPDATED R
Fig. A-UBBAA Sheet 02 SHEET UPDATED R
Fig. A-UBBAA Sheet 03 SHEET UPDATED R
Fig. A-UBBAA Sheet 04 SHEET ADDED N
Fig. A-UBBAB FIGURE SOLUTION UPDATED R
Fig. A-UBBAB Sheet 01 SHEET UPDATED R
Fig. A-UBBAB Sheet 02 SHEET UPDATED R
Fig. A-UBBAB Sheet 03 SHEET UPDATED R
Fig. A-UBBAB Sheet 04 SHEET ADDED N
Fig. A-UBBAC FIGURE SOLUTION UPDATED R
Fig. A-UBBAC Sheet 01 SHEET UPDATED R
Fig. A-UBBAC Sheet 02 SHEET UPDATED R
Fig. A-UBBAC Sheet 03 SHEET UPDATED R
Fig. A-UBBAC Sheet 04 SHEET ADDED N
Fig. A-UBBAD FIGURE SOLUTION UPDATED R
Fig. A-UBBAD Sheet 01 SHEET UPDATED R
Fig. A-UBBAD Sheet 02 SHEET UPDATED R
Fig. A-UBBAD Sheet 03 SHEET UPDATED R

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 19

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET

Fig. A-UBBAD Sheet 04 SHEET ADDED N

Appendix 01: Manpower Gantt Chart
APPENDIX CONTENT APPENDIX CONTENT ADDED N
Fig. A-UAAAA FIGURE SOLUTION UPDATED R
Appendix 02: Configuration Definition Table
APPENDIX CONTENT APPENDIX CONTENT ADDED N

FILING INSTRUCTIONS

This Service Bulletin has been generated electronically and is reissued as a complete document.
Replace the complete document.

Put this Revision Transmittal Sheet in front of the Service Bulletin.

HISTORY OF PREVIOUS REVISIONS

Revision No 01 issued to correct reidentification of the fairings, add sentences for monitored retrofit in
paragraph Industry Support Information and include minor corrections. Also, this revision issued to
update the manpower and the procedure following the validation report of this Service Bulletin on MSN
0069.

Revision No. 02 issued to correct the Configurations in this Service Bulletin and the reidentification of
the fairings. Also this Revision adds minor corrections in the Accomplishment Instructions.

REVISION SEQUENCE

ORIGINAL: Nov 03/14

REVISION No. : 01 - Oct 23/15

REVISION No. : 02 - Feb 12/16

REVISION No. : 03 - Nov 09/17

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 20

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
Tel : (33) 5 61 93 33 33
Telex : AIRBU 530526F
Fax : (33) 5 61 93 42 51

This summary is for information only and is not approved for modification of the aircraft.

ATA SYSTEM: 52

TITLE: DOORS - MAIN GEAR DOORS - INTRODUCE NEW FAIRING

ATTACHMENT STUD ASSEMBLIES
**CONF ALL

MODIFICATIONS

MODIFICATION CLASSIFICATION
MAJOR None
MINOR 155648J3676

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting the
airworthiness of the product. All other changes are major changes.

REASON/DESCRIPTION/OPERATIONAL CONSEQUENCES

AIRBUS have received reports of wear and corroded forward upper and lower Post Modification
No. 27716J1969 attachment/adjustment studs on the Main Landing Gear (MLG) Door Assembly.
Modification No. 27716J1969 previously introduced attachment/adjustment studs with increased
strength. These subsequent findings of wear and corrosion have led to the issue of Inspection Service
Bulletin (ISB) No. A320-52-1163. This gives instructions for a repetitive inspection until a terminating
modification is available.

This Service Bulletin introduces a rod and adjuster with improved corrosion resistance and locking
feature. These will reduce the possibility of wear and corrosion.

This Service Bulletin cancels Inspection Service Bulletin A320-52-1163.

This Service Bulletin supersedes Service Bulletin A320-52-1100.

The Operational/Maintenance Consequences of this Service Bulletin are covered by the update of the
affected publications detailed in PLANNING INFORMATION

GENERAL EVALUATION

EVALUATION TABLE
COMPLIANCE RECOMMENDED (1) CANCELS INSPECTION SB YES
POTENTIAL AD NO A/C OPERATION AFFECTED NO
RELIABILITY AFFECTED NO PAX COMFORT AFFECTED NO

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 1

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

EVALUATION TABLE
COST SAVING NO ETOPS AFFECTED NO
STRUCTURAL LIFE EXTN NO VENDOR SB INVOLVED NO
NORMAL JACKING YES VALIDATION ON AIRCRAFT YES
BOOKLET AVAILABLE YES

NOTE (1): Service Bulletin recommended to be accomplished to prevent significant operational

disruptions.

NOTE: This Service Bulletin has been validated at original issue on A320 aircraft with
Manufacturer Serial Number (MSN) 0069.

MATERIAL PRICE INFORMATION

**CONF 001

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B01R01 1 3,020.00 Nut, Locking Device, Stud Adjust, Plate
Support, Rod End-Assy, Plate-Ident
Kit 521165B03R00 1 130.00 Plate-Ident
TOTAL 3,150.00
Standard tool TOOLB01 1 See SB Spacer-Rigging
Component COMPB01 1 See SB Cotter Pins

**CONF 002

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B02R01 1 2,620.00 Nut, Locking Device, Stud Adjust, Rod
End-Assy, Plate-Ident
Kit 521165B03R00 1 130.00 Plate-Ident
TOTAL 2,750.00
Standard tool TOOLB01 1 See SB Spacer-Rigging
Component COMPB02 1 See SB Cotter Pins

**CONF 003

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B01R01 1 3,020.00 Nut, Locking Device, Stud Adjust, Plate
Support, Rod End-Assy, Plate-Ident
Kit 521165B03R00 1 130.00 Plate-Ident
TOTAL 3,150.00
Standard tool TOOLB01 1 See SB Spacer-Rigging

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 2

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Component COMPB01 1 See SB Cotter Pins

**CONF 004

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B01R01 1 3,020.00 Nut, Locking Device, Stud Adjust, Plate
Support, Rod End-Assy, Plate-Ident
Kit 521165B03R00 1 130.00 Plate-Ident
TOTAL 3,150.00
Standard tool TOOLB01 1 See SB Spacer-Rigging
Component COMPB01 1 See SB Cotter Pins

**CONF 005

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B01R01 1 3,020.00 Nut, Locking Device, Stud Adjust, Plate
Support, Rod End-Assy, Plate-Ident
Kit 521165B03R00 1 130.00 Plate-Ident
TOTAL 3,150.00
Standard tool TOOLB01 1 See SB Spacer-Rigging
Component COMPB01 1 See SB Cotter Pins

**CONF 006

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B02R01 1 2,620.00 Nut, Locking Device, Stud Adjust, Rod
End-Assy, Plate-Ident
Kit 521165B03R00 1 130.00 Plate-Ident
TOTAL 2,750.00
Standard tool TOOLB01 1 See SB Spacer-Rigging
Component COMPB02 1 See SB Cotter Pins

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 3

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

**CONF 007

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B01R01 1 3,020.00 Nut, Locking Device, Stud Adjust, Plate
Support, Rod End-Assy, Plate-Ident
Kit 521165B03R00 1 130.00 Plate-Ident
TOTAL 3,150.00
Standard tool TOOLB01 1 See SB Spacer-Rigging
Component COMPB01 1 See SB Cotter Pins

**CONF 008

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B02R01 1 2,620.00 Nut, Locking Device, Stud Adjust, Rod
End-Assy, Plate-Ident
Kit 521165B03R00 1 130.00 Plate-Ident
TOTAL 2,750.00
Standard tool TOOLB01 1 See SB Spacer-Rigging
Component COMPB02 1 See SB Cotter Pins

**CONF 009

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B02R01 1 2,620.00 Nut, Locking Device, Stud Adjust, Rod
End-Assy, Plate-Ident
Kit 521165B03R00 1 130.00 Plate-Ident
TOTAL 2,750.00
Standard tool TOOLB01 1 See SB Spacer-Rigging
Component COMPB02 1 See SB Cotter Pins

**CONF 010

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B02R01 1 2,620.00 Nut, Locking Device, Stud Adjust, Rod
End-Assy, Plate-Ident
Kit 521165B03R00 1 130.00 Plate-Ident
TOTAL 2,750.00
Standard tool TOOLB01 1 See SB Spacer-Rigging

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 4

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Component COMPB02 1 See SB Cotter Pins

**CONF 011

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B02R01 1 2,620.00 Nut, Locking Device, Stud Adjust, Rod
End-Assy, Plate-Ident
Kit 521165B03R00 1 130.00 Plate-Ident
TOTAL 2,750.00
Standard tool TOOLB01 1 See SB Spacer-Rigging
Component COMPB02 1 See SB Cotter Pins

**CONF 012

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B02R01 1 2,620.00 Nut, Locking Device, Stud Adjust, Rod
End-Assy, Plate-Ident
Kit 521165B03R00 1 130.00 Plate-Ident
TOTAL 2,750.00
Standard tool TOOLB01 1 See SB Spacer-Rigging
Component COMPB02 1 See SB Cotter Pins

**CONF 013

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B02R01 1 2,620.00 Nut, Locking Device, Stud Adjust, Rod
End-Assy, Plate-Ident
Kit 521165B03R00 1 130.00 Plate-Ident
TOTAL 2,750.00
Standard tool TOOLB01 1 See SB Spacer-Rigging
Component COMPB02 1 See SB Cotter Pins

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 5

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

**CONF 014

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B01R01 1 3,020.00 Nut, Locking Device, Stud Adjust, Plate
Support, Rod End-Assy, Plate-Ident
Kit 521165B03R00 1 130.00 Plate-Ident
TOTAL 3,150.00
Standard tool TOOLB01 1 See SB Spacer-Rigging
Component COMPB01 1 See SB Cotter Pins

**CONF 015

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B01R01 1 3,020.00 Nut, Locking Device, Stud Adjust, Plate
Support, Rod End-Assy, Plate-Ident
Kit 521165B03R00 1 130.00 Plate-Ident
TOTAL 3,150.00
Standard tool TOOLB01 1 See SB Spacer-Rigging
Component COMPB01 1 See SB Cotter Pins

**CONF 016

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B02R01 1 2,620.00 Nut, Locking Device, Stud Adjust, Rod
End-Assy, Plate-Ident
Kit 521165B03R00 1 130.00 Plate-Ident
TOTAL 2,750.00
Standard tool TOOLB01 1 See SB Spacer-Rigging
Component COMPB02 1 See SB Cotter Pins

**CONF 017

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B02R01 1 2,620.00 Nut, Locking Device, Stud Adjust, Rod
End-Assy, Plate-Ident
Kit 521165B03R00 1 130.00 Plate-Ident
TOTAL 2,750.00
Standard tool TOOLB01 1 See SB Spacer-Rigging

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 6

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Component COMPB02 1 See SB Cotter Pins

**CONF 018

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B02R01 1 2,620.00 Nut, Locking Device, Stud Adjust, Rod
End-Assy, Plate-Ident
Kit 521165B03R00 1 130.00 Plate-Ident
TOTAL 2,750.00
Standard tool TOOLB01 1 See SB Spacer-Rigging
Component COMPB02 1 See SB Cotter Pins

**CONF 019

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B02R01 1 2,620.00 Nut, Locking Device, Stud Adjust, Rod
End-Assy, Plate-Ident
Standard tool TOOLB01 1 See SB Spacer-Rigging
Component COMPB02 1 See SB Cotter Pins

**CONF 020

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTY PER PRICE PER MAIN PARTS
A/C A/C (USD)
Kit 521165B02R01 1 2,620.00 Nut, Locking Device, Stud Adjust, Rod
End-Assy, Plate-Ident
Standard tool TOOLB01 1 See SB Spacer-Rigging
Component COMPB02 1 See SB Cotter Pins

EFFECTIVITY

**CONF ALL

This Service Bulletin is applicable to this (these) operator(s) :

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 7

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

03Q 06R 10N 11S 11X 13Y 15T 16T 17M 17R 17S 19R 20Q
23R 27V 28M 29S 31V 31X 32Q 36R 38W 39N 40N 40S 41N
41S 43S 45O 46U 47P 48O 48P 52T 53Z 56O 59Z 60U 61W
66X 69X 73W 74T 76W 78X 79W 80X 82U 83O 83Q 83V 84M
85T 86P 86Z 87Q 89Q 89T 91X 95V 95W 96Q 98W 98X AAF
AAL AAR AAV AAW AAY ABL ABQ ABY ACA ACI ADR AEE AFL
AFR AHY AIC AIJ ALK AMC AMU ANA ANR ANZ AOJ APJ ART
ARU ASL ASV ATR AUA AUH AVA AVJ AWC AWW AXM AZA B2V
BAW BEC BEG BEL BER BGF BGH BJN BKP BRS BSX BTK BTN
BUC C2C C9G CBG CBJ CCA CCM CDC CEB CEF CES CFG CGH
CHB CQH CQN CRK CSA CSC CSN CSZ CTN CTV CYP DAL DAT
DCS DKH DLH DNU DQA DRK DTR EAF EDW EIN ELB ERN ESW
ETD ETJ EVA EVE EWE EWG EZY F2I FCB FFT FHY FIA FIN
FJW FLI FRN FTZ G4I G8E GAF GAP GBB GCA GCR GFA GLG
GMI GOW GSW GWI GWR GZQ HDA HFY HKE HKJ HTU HVN HYP
I2L I2T IAW IBE IBS IGO IND IRA IRC IRM ISR ISS IYE
IZG JAD JAS JAV JBU JBW JJP JSA JST JZR KAC KAY KFR
KHO KHV KKK KNE KZR LAA LAN LAO LBT LFO LJB LKE LKH
LLC LLM LLP LLX LMJ LMU LUR LWA LZB MAC MAU MEA MGF
MJF MJN MLD MLM MMA MON MOV MRJ MSC MSR MXA MYX NIA
NKS NLY NMA NMB NSS NVD NVR NWS OBS OHY OLY OMS ONE
ORF OTF OZW PAL PGT PIA PIC PKZ PTI QAF QDA QQE QSM
QTR R1T RBA RBG RCT RIH RJA RJD ROT RWZ RYW RZO SAA
SAI SAS SBI SDM SDR SEK SEY SFJ SFW SHJ SHU SKU SLK
SND SNG SNX SOL SSG SUD SVA SVR SVW SWM SWR SYR TAE
TAI TAM TAP TAR TBA TBZ TCW TCX TDR TGW THA THD THY
TJS TNA TTW U6A UAE UAL UEA UJX UKN UNA USA UZB VAW
VIP VIV VJC VKG VLG VNL VOE VOI VRD VRE VVC WAN WHT
WOW WRC WZZ

CONCURRENT REQUIREMENTS

None

REFERENCES / REPERCUSSIONS

TFU 52.81.00.014
OEB None
AOT None
SIL None
ISI None
LINE MAINTENANCE AFFECTED No
LIFE LIMIT None
OTHER None

NATURE OF THE WORK

AIRCRAFT YES
EQUIPMENT NO
HARD NO
SOFT NO
OBRM NO

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 8

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

MANPOWER

**CONF 001

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 002

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 003

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

Task 521165-831-898-001: Modification - Additional Work 3 for Aircraft Concerned by

Configurations 003 and 006 of this Revision and Modified by Revision No. 02 or any Previous
Issue, or Reidentified by the Additional Work from Revision No. 01 or Revision No. 02
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 004

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 9

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

**CONF 005

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 006

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

Task 521165-831-898-001: Modification - Additional Work 3 for Aircraft Concerned by

Configurations 003 and 006 of this Revision and Modified by Revision No. 02 or any Previous
Issue, or Reidentified by the Additional Work from Revision No. 01 or Revision No. 02
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 007

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 008

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 10

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

**CONF 009

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 010

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 011

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 012

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 11

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

**CONF 013

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 014

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 015

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 016

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

Task 521165-831-897-001: Modification - Additional Work 2 for Aircraft Concerned by

Configuration 016 of this Revision and Modified by the Original Issue or Revision No. 01, or
Reidentified by the Additional Work from Revision No. 01
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 12

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

**CONF 017

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 018

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 019

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

**CONF 020

Task 521165-831-895-001: Modification

TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

APPENDICES

**CONF ALL

Appendix 01: Manpower Gantt Chart

Appendix 02: Configuration Definition Table

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 13

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

**CONF 001, 004 thru 005, 014 thru 015

LH SHOWN
RH SIMILAR

B
FORWARD STUDS

NOTE:
AREA OF MODIFICATION
N_SB_521165_7_SAAA_01_00

Figure A-USAAA - Sheet 01

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 14

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

**CONF 002, 008, 012 thru 013, 016 thru 018, 020

LH SHOWN
RH SIMILAR

B
FORWARD STUDS

NOTE:
AREA OF MODIFICATION
N_SB_521165_7_SAAB_01_00

Figure A-USAAB - Sheet 01

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 15

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

**CONF 003, 007

LH SHOWN
RH SIMILAR

B
FORWARD STUDS

NOTE:
AREA OF MODIFICATION
N_SB_521165_7_SAAC_01_00

Figure A-USAAC - Sheet 01

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 16

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

**CONF 006, 009 thru 011, 019

LH SHOWN
RH SIMILAR

B
FORWARD STUDS

NOTE:
AREA OF MODIFICATION
N_SB_521165_7_SAAD_01_00

Figure A-USAAD - Sheet 01

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 17

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY

This Page Intentionally Left Blank

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 18

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
Tel : (33) 5 61 93 33 33
Telex : AIRBU 530526F
Fax : (33) 5 61 93 42 51

ATA SYSTEM: 52

TITLE: DOORS - MAIN GEAR DOORS - INTRODUCE NEW FAIRING

ATTACHMENT STUD ASSEMBLIES
MODIFICATION No.: 155648J3676
This document contains AIRBUS PROPRIETARY INFORMATION and shall at all times remain the
property of AIRBUS; no intellectual property right or licence is granted by AIRBUS in connection with
any information contained in it. It is delivered on the express condition that said document and the
information contained in it shall be treated as confidential, shall not be used for any purpose other than
that for which it is hereby delivered. It shall not be disclosed in whole or in part to third parties and shall
not be duplicated in any manner (except for the purposes of performing the tasks described hereunder
and provided that any recipient of such document shall comply with the conditions herein), without
AIRBUS prior written consent.

1. PLANNING INFORMATION

**CONF ALL

A. EFFECTIVITY

NOTE: This modification is embodied before delivery on aircraft with Manufacturer

Serial Number (MSN) 6160, 6167 and subsequent.

(1) Models

318-111 318-112 318-121 318-122 319-111 319-112 319-113 319-114

319-115 319-131 319-132 319-133 320-211 320-212 320-214 320-216
320-231 320-232 320-233 321-111 321-112 321-131 321-211 321-212
321-213 321-231 321-232

(2) Effectivity by MSN

0029 0045-0046 0049-0057 0059 0064-0073 0076-0078 0081-0087 0093-0094 0099

0104 0110-0113 0115-0118 0121-0127 0135 0137-0138 0140-0142 0148-0150
0152-0154 0157 0159-0162 0164-0166 0168-0169 0171-0172 0174-0175 0178
0181-0183 0185 0192 0194-0195 0197-0198 0200-0203 0205-0206 0208-0211 0213
0216-0220 0229-0232 0234 0237 0239 0242-0243 0248-0249 0251-0256 0259-0260
0262-0263 0265 0267-0269 0272-0273 0275-0277 0279 0281-0282 0284-0285 0287
0289-0294 0296-0298 0300-0303 0306-0309 0311-0312 0314 0316-0322 0324-0325
0328-0332 0339-0343 0345-0347 0350-0351 0353-0355 0357-0358 0360-0362 0364
0366-0368 0370-0373 0376 0378 0380-0382 0385-0388 0390 0393 0395 0398-0410
0412 0414-0418 0420-0424 0426-0432 0434-0436 0438-0439 0441-0442 0444-0445
0447-0450 0452 0454 0456-0458 0460 0462-0466 0468 0470 0472-0477 0479-0480

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 1

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

0482-0491 0493 0495-0514 0516-0535 0537-0546 0548-0556 0558-0587 0589

0591-0593 0595-0600 0603-0604 0607-0614 0616-0623 0625 0627 0629-0631
0633-0662 0664-0673 0675-0706 0709 0711-0746 0748-0752 0754-0771 0773-0788
0790-0798 0800-0898 0900-0953 0955 0957-0968 0970-0977 0979-1043 1045-1067
1069-1073 1075-1097 1099-1112 1114-1144 1146-1185 1187-1217 1219-1277
1279-1304 1306-1332 1334-1373 1375-1463 1465-1607 1609-1659 1661-1675
1677-1697 1699-1726 1728 1730-1767 1769-1812 1814-1821 1823-1829 1831-1918
1920-1929 1931-1938 1940-1984 1986-1990 1993-2016 2018-2024 2026-2050
2052-2057 2059-2087 2089-2110 2112-2127 2129-2217 2219-2275 2277-2423
2425-2499 2501-2721 2723-2890 2892-2940 2942-3037 3039-3091 3093-3109
3111-3162 3164-3243 3245-3647 3649-3820 3822-4329 4331-4449 4451-6100
6102-6159 6161-6166

(3) Effectivity by Operator

The Operator/MSN relationship is provided for information only and is correct at the time
of issue in accordance with the information available to AIRBUS. Any future changes
resulting from transfer of an aircraft from one operator to another will not be reflected in
this list unless the Service Bulletin is revised for another reason.

OPERATOR MSN
03Q 0584 0620 0631 0770
06R 0527
10N 0517 0734
11S 4211
11X 0115
13Y 0371
15T 0764 1494 2910 3261
16T 4024 4679
17M 3856 5445
17R 5768
17S 3333
19R 0781
20Q 4842
23R 1730
27V 3826
28M 0055
29S 0291 0292
31V 0164 0293 0332 0420 0436 0565 0579 0591 0760 0816 0855 0932
0943 0992 1048
31X 4319
32Q 1228 1283
36R 1747 1818
38W 1194
39N 1893
40N 0065
40S 1973
41N 3164
41S 0630

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 2

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

OPERATOR MSN
43S 4650
45O 5040
46U 2906 2952 2982 3275 3296 3332 3674 3734 3986 4053 5218 5900
6032
47P 0619
48O 3362 3412
48P 2192
52T 1599
53Z 1468
56O 1285
59Z 1556
60U 0325
61W 0112
66X 1276
69X 0219 0300 0328
73W 0087
74T 2165 4768
76W 0140 0157
78X 1081
79W 3751
80X 2748
82U 0279
83O 0316
83Q 0477 0495
83V 0908 2236
84M 3216 3635
85T 0234
86P 0913
86Z 1706 1750
87Q 0052
89Q 0142 0645 0677 0891
89T 3356
91X 2837
95V 3379
95W 2949 4199
96Q 5182
98W 0434 0441 0516 0524 1093 1108 1943
98X 0551
AAF 0639 2180 2870 3136 3242 3289 4589 4675 4758 4767 6012
AAL 5327 5678 5698 5704 5745 5753 5761 5781 5786 5788 5789 5798
5810 5827 5834 5842 5860 5884 5895 5904 5932 5938 5946 5955
5975 5983 5991 6020 6040 6046 6063 6070 6085 6094 6150 6154
6162
AAR 1174 1356 1511 2397 2459 3437 3483 3496 3641 3873 4112 5169
5173 5287 5350 5382 5462 5500 5636
AAV 1422 2331 2340

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 3

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

OPERATOR MSN
AAW 3224 3236 3615 3657 4004 4521 5414 5448
AAY 0706 0714 0716 0730 0745 1171 1210 1229 1255 1262 1288 1292
1318 1347 1372 1467 1530 1540 1694 2001 2176 2224 2265 2271
2319 2387 2398 2420 2427 2450 2556 2586 2625 2638 2702 2709
2729 2786 2821 2876 3084 4015
ABL 1227 1636 1670 1734 1970 2041 2045 2110 2226 2247 2290 2422
2430 2732 2808 2840 2927 2933 2943 3297
ABQ 3974 5891 5943 5966 6016 6067 6119
ABY 4468 4524 4890 4958 5017 5276 5307 5423 5452 5502 5576 5718
5772 5889 5903 5984 6000 6054
ACA 0059 0068 0073 0084 0122 0126 0127 0141 0149 0150 0154 0159
0174 0175 0183 0210 0231 0232 0242 0248 0253 0254 0255 0265
0277 0284 0290 0309 0324 0330 0341 0378 0403 0404 0546 0572
0634 0656 0670 0672 0682 0688 0691 0693 0695 0697 0711 0719
0721 0728 0732 0736 0740 0742 0752 0757 0769 0773 0779 0785
0800 0813 0817 0829 0831 0840 0845 1299 1562 1577 1602 1611
1623 1632 1638 1673 1691 1719 1726 1742 1748 1772 1783 1787
1811 1853 1864 1874 1940 1975 2018 2145 3051 3401 3884
ACI 2152 3547
ADR 1000 4282 4301
AEE 1428 1433 1856 1996 2468 2828 3033 3066 3074 3162 3302 3316
3322 3365 3392 3423 3439 3462 3478 3484 3519 3526 3527 3709
3714 3745 3748 3753 3773 3785 3812 3820 3829 3850 3878 3990
4065 4094 4165
AFL 2106 2116 2133 2144 3157 3267 3334 3373 3410 3511 3545 3574
3627 3631 3640 3644 3699 3711 3778 3786 3835 3923 3954 4058
4074 4099 4103 4116 4133 4148 4160 4453 4461 4498 4500 4579
4625 4649 4656 4684 4692 4712 4835 5044 5059 5271 5421 5536
5565 5572 5578 5580 5585 5614 5720 5755 5790 5873 5881 5913
5921 5967 5970 5974 5982 5989 6017 6022 6043 6044 6060 6071
6090
AFR 0237 0287 0498 0509 0521 0529 0544 0598 0600 0608 0618 0625
0637 0777 0796 0985 1020 1025 1036 1133 1151 1169 1176 1190
1201 1216 1267 1271 1344 1404 1415 1444 1449 1471 1476 1502
1505 1524 1616 1622 1640 1645 1658 1677 1699 1733 1859 1879
1894 1900 1924 1938 1949 2035 2059 2071 2081 2100 2109 2140
2317 2344 2350 2456 2582 2601 2686 2705 2716 2721 2750 2918
2938 2951 2961 2967 2972 3008 3009 3098 3372 3399 3419 3420
3441 3470 3777 3795 3814 3825 3859 3930 4063 4084 4105 4137
4139 4241 4251 4267 4295 4298 4335 4402 4601 4604 4664 4714
4747 4800 4820 4901 4908 5084 5129 5719 5802 5869
AHY 0331 2487 2516 2588 2685 2788 2846 2853 2865 2991 3006
AIC 0045 0046 0049 0050 0051 0056 0057 0398 0416 0423 0431 0432
0486 0490 0499 2593 2624 2629 2907 3130 3146 3212 3271 3288
3300 3305 3326 3340 3344 3367 3498 3551 3557 3573 3619 3620
3687 3752 3792 3822 3874 3918 3955 3970 4002 4009 4020 4029
4052 4078 4089 4096 4121 4138 4155 4164 4201 4212 4236 4237
4280

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 4

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

OPERATOR MSN
AIJ 0169 1132 1162 1179 1244 1259 1308 1322 1780 2048 2227 2539
2930 2964 3021 3044 3123 3149 3160 3286 3304 3312 3374 3508
3514 3667 3690 4235 4304 4411 4730 4733 4924 4933 5163 5221
5358 5372 5653 5665 5867 5878 5933
ALK 1946 2345 2731 3397 3636 4694 4869 4915 5086
AMC 1979 2186 2189 2291 2665 2768 3056 3068
AMU 1758 1790 1850 1912 1926 1962 4197 5352 5459 5523
ANA 0482 0501 0507 0531 0534 0549 0554 0658 0669 0685
ANR 0671 0765
ANZ 2085 2090 2112 2130 2148 2153 2173 2257 2297 2445 2533 2594
2663 4553 4584 4884 4926 5629 5682 5847 5962 5993
AOJ 4503
APJ 4887 4936 5015 5166 5304 5384 5440 5540 5640 5724 5874 6004
6107
ART 0533 0566 0662 1762 1823 1873 2211 2233
ARU 0582 0805 1583
ASL 1140 1159 2277 2296 2335 2587 2621 2645 3252 3317
ASV 4142 5035 5767 5774
ATR 0314 0373 0393
AUA 0552 0570 0581 0768 0776 0797 0920 0935 1137 1150 1189 1385
1387 1458 1478 1504 1553 1678 1735 1931 1937 2009 2131 2174
2262 2416 2494 2547 2652 5122 5181
AUH 2403
AVA 1634 2328 2333 2358 2367 2377 2394 2523 2544 2552 2575 3647
3664 3691 3961 3980 3988 3992 4001 4011 4026 4046 4051 4167
4200 4281 4284 4345 4381 4567 4599 4763 4789 4821 4862 4939
5057 5119 5195 5360 5398 5454 5477 5622 5632 5840 5944 6138
6153
AVJ 0368 0406
AWC 2564 2791 3830 4039 4701
AWW 0597
AXM 0667 0743 0872 0874 1286 2147 2162 2183 2425 2612 2633 2656
2683 2699 2760 2816 2826 2842 2881 2885 2956 2989 3000 3018
3052 3064 3117 3140 3154 3173 3182 3194 3201 3223 3232 3277
3291 3299 3327 3338 3353 3370 3394 3404 3427 3448 3477 3486
3489 3505 3521 3536 3549 3568 3576 3582 3610 3628 3679 3701
3715 3729 3765 3776 3813 3875 3963 3997 4019 4035 4070 4079
4088 4098 4126 4147 4263 4278 4293 4302 4333 4346 4361 4367
4386 4390 4404 4426 4458 4462 4477 4486 4557 4562 4571 4582
4641 4727 4793 4797 4807 4815 4882 4889 4917 4964 4969 4979
4980 4989 5098 5109 5137 5149 5153 5165 5200 5215 5272 5283
5325 5344 5347 5353 5359 5397 5420 5428 5430 5431 5468 5505
5547 5593 5619 5627 5657 5703 5706 5762 5812 5824 5839 5846
5851 5863 5866 5888 5897 5905 5908 5914 5918 5959 6015 6034
6048 6064 6075 6084 6088 6145 6158

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 5

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

OPERATOR MSN
AZA 0513 0514 0526 0576 0583 0586 0593 0599 0819 0848 0940 0951
0959 1138 1168 1217 1220 1226 1448 1457 1473 1480 1489 1722
1740 1745 1770 1779 2033 2057 2074 2083 2086 2101 2127 2869
2932 2995 3076 3079 3115 3138 3161 3343 3563 3598 3609 3643
3666 3695 3732 3815 3846 3885 3906 3921 3956 3976 3978 4075
4108 4119 4143 4152 4195 4249 4520 4523 4536 4759 4764 4859
4875 4910 5018 5130 5294 5383 5424
B2V 0185
BAW 1014 1082 1115 1118 1142 1177 1193 1197 1222 1225 1232 1236
1239 1258 1261 1279 1295 1329 1338 1380 1384 1418 1423 1424
1440 1445 1466 1482 1509 1510 1513 1529 1537 1558 1574 1590
1594 1604 1606 1613 1661 1665 1672 1687 1689 1690 1696 1708
1711 1754 1760 1771 1782 1804 1814 1829 1834 1871 1883 1892
1899 1902 1907 1910 1958 1987 2038 2040 2098 2188 2190 2194
2305 2320 2323 2324 2351 2363 2389 2429 2441 2466 2536 2653
2694 2697 2720 2799 2981 3049 3081 3089 3235 3254 3290 3301
3314 3351 3468 3499 3512 3550 3607 3649 3697 3703 3721 3726
3912 3926 4007 4185 4238 4265 4306 4464 4551 4725 4791 4975
5634 5784 5856 5948 5985 6028 6091 6129 6155
BEC 3199 5538
BEG 3139
BEL 1086 1102 1160 1336 1388 1441 1493 1759 1797 1803 1838 1885
1929 1963 1968 1983 2030 2114 2196 2207 2230 2260 2287 2392
2400 2700 2763 2810 2925 3255 3790 3895 4243 4275
BER 1717 1769 1775 1852 1889 1961 2003 2562 2591 2606 2627 2668
2749 2867 2902 2968 3055 3080 3093 3121 3178 3202 3213 3245
3295 3328 3415 3422 3447 3464 3482 3502 3515 3516 3532 3540
3594 3604 3661 3689 3700 3704 3728 3865 3908 3945 3995 4013
4033 4101 4128 4161 4187 4269 4291 4294 4316 4329 4368 4433
4510 4565 4581 4594 4606 4631 5522 5648
BGF 3188
BGH 1087 1554 2844 2863 3125
BJN 3617 4956
BKP 2254 2273 2310 2362 2366 2383 2417 2467 2509 2531 2600 2634
2648 2660 2664 2783 3421 3424 3454 3672 3694 3759 3911
BRS 2263
BSX 0648 0650 3577
BTK 6164
BTN 1541 1551
BUC 0256 0259 0276 0296 0320 0321 0353
C2C 5023 5088 5907
C9G 2023
CBG 4970 5260 5266 6096
CBJ 2557 2561 2611 2644 2733 2985 3285 3520 3548 3561 3578 3580
3638 3842 3851 3914 3958 3982 4388 4410 4412 4428 4440 4471
4483 4505 4513 4529 4540 4580 4602 4677 5008 5072 5114 5185
5216 5331 5471 5630 5656 5722 5848 5997 6041

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 6

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

OPERATOR MSN
CCA 0876 0921 2000 2007 2015 2172 2202 2205 2237 2269 2285 2293
2298 2454 2499 2508 2525 2532 2545 2551 2559 2614 2643 2805
2819 2839 2847 2890 3195 3200 3215 3221 3226 3250 3307 3329
3337 3461 3506 3523 3601 3623 3653 3655 3665 3678 3722 3725
3766 3806 3940 3973 4022 4031 4062 4091 4131 4180 4221 4283
4317 4318 4348 4377 4472 4473 4494 4538 4566 4593 4617 4719
4771 4775 4803 4829 4834 4873 4895 4900 4949 4963 4985 4997
5014 5032 5054 5091 5124 5174 5199 5265 5346 5386 5419 5432
5435 5568 5573 5600 5664 5690 5743 5771 6013 6159
CCM 3325 3882 3952 5887 5906
CDC 6026 6055 6065 6157
CEB 2790 2831 2852 2994 3048 3272 3762 3767 4447 4508 4537 4574
4852 4861 4870 4927 4993 5045 5067 5250 5320 5381 5442 5498
5669 5687 5917 5934 6021 6051
CEF 2801 3085
CES 0665 0754 0838 0854 0897 0909 0925 0939 1028 1030 1070 1072
1303 1312 1316 1330 1345 1357 1361 1377 1386 1532 1542 1601
1639 1906 1911 1964 1981 2022 2034 2036 2049 2056 2068 2219
2221 2235 2239 2244 2309 2315 2437 2451 2478 2493 2498 2543
2549 2693 2757 2825 2882 2895 3168 3170 3186 3197 3233 3247
3249 3262 3471 3481 3559 3593 3611 3612 3613 3639 3650 3677
3682 3692 3716 3775 3793 3797 3870 3904 3929 3937 3965 3969
4027 4037 4043 4045 4111 4144 4186 4198 4209 4220 4239 4240
4252 4297 4309 4340 4342 4355 4374 4423 4627 4638 4659 4685
4702 4709 4711 4718 4722 4723 4729 4746 4748 4765 4769 4776
4799 4831 4844 4857 4877 4886 4903 4938 4946 4967 4987 5047
5048 5053 5063 5135 5136 5144 5156 5192 5210 5227 5242 5267
5273 5309 5326 5330 5338 5363 5376 5380 5402 5412 5439 5461
5481 5508 5516 5519 5524 5527 5558 5575 5623 5628 5668 5691
5700 5705 5710 5711 5726 5735 5759 5770 5823 5826 5852 5864
5886 5920 5942 5973 5998 6052 6062 6089 6111 6116 6127 6137
6144 6151
CFG 0774 0809 0884 0894 0905 0957 0971 1416 1437 1607 5969 6053
CGH 3768 3849 4522
CHB 4231 4262 4452 4482 4569 4644 4686 4687 4995 5105 5246 5626
5679 5740 5912 6023 6076 6120
CQH 2939 3014 3023 3747 3819 4072 4093 4168 4244 4331 4366 4373
4375 4499 4586 4738 4750 4760 4809 4816 4909 4978 4983 5022
5051 5108 5378 5403 5434 5446 5466 5562 5778 5816 5911 6073
6117
CQN 0696 0698 0704 0705 3828 3836 3876 3901 3903 3941 4140 4696
5645 5713 5875 5930
CRK 5147 5189 5416 5514 5544 6003
CSA 3043 3094 3406 3436 3452 3660 3892 4258 4713

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 7

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

OPERATOR MSN
CSC 0878 0915 0919 1013 2313 2348 2431 2510 2534 2597 2639 3114
3116 3124 3158 3167 3196 3210 3386 3449 3583 3591 3680 3730
3893 3962 3996 4018 4068 4288 4326 4378 4420 4424 4525 4575
4619 4642 4660 4707 4731 4824 4830 4856 4905 4911 4923 5041
5121 5141 5160 5197 5208 5233 5286 5303 5389 5470 5543 5609
5646 5647 5650 5670 5765 5868 5896 5910 5937 5953 5964 5977
6008 6030 6148
CSN 0712 0718 0720 0722 0849 0859 0881 0895 0900 0950 0966 1035
1039 1057 1596 1614 1776 1788 1971 1974 1986 1995 2004 2008
2067 2080 2200 2203 2232 2354 2361 2371 2408 2426 2435 2484
2505 2506 2511 2519 2521 2530 2541 2546 2554 2555 2558 2574
2579 2637 2689 2701 2708 2713 2741 2743 2759 2767 2770 2772
2796 2809 2824 2834 2855 2861 2877 2899 2915 2936 2950 2960
2971 2986 3067 3075 3112 3217 3241 3251 3269 3311 3342 3459
3493 3507 3552 3566 3587 3645 3681 3764 3784 3847 3860 3867
3890 3910 3920 3934 3938 3951 3959 3981 3983 3999 4003 4017
4036 4038 4071 4172 4184 4189 4194 4205 4217 4224 4225 4230
4232 4248 4260 4266 4271 4274 4279 4290 4292 4299 4322 4325
4338 4341 4350 4362 4365 4369 4370 4387 4396 4416 4430 4456
4507 4550 4613 4671 4751 4782 4794 4808 4836 4854 4864 4880
4883 4912 4919 4928 4982 5061 5151 5168 5170 5183 5202 5214
5225 5237 5268 5279 5288 5410 5480 5484 5503 5506 5534 5561
5564 5579 5602 5611 5655 5671 5693 5730 5736 5750 5756 5797
5817 5832 5837 5890 5945 5949 5976 6018 6049 6078 6104 6106
6146
CSZ 2672 2684 2841 2905 2909 2935 2973 2980 3131 3132 3153 3206
3366 3383 3435 3440 3456 3528 3599 3696 3698 3756 3848 3855
3887 3898 3935 3971 4010 4028 4159 4176 4208 4214 4226 4300
4359 4407 4409 4435 4474 4514 4531 4620 4633 4666 4726 4845
4866 4876 4897 4920 4929 4977 4986 5002 5082 5110 5176 5369
5521 5550 5589 5639 5731 5766 5986 6019
CTN 0767 0833 1009 1029 1237 1252
CTV 0839 0892 1635 2598 2692 3147 3148 3861 4961 5351 5379 5394
5399 5415 5511 5541 5551 5556 5560 5571 5574 5597 5777 5830
6118
CYP 1129
DAL 0118 0121 0125 0152 0153 0160 0171 0192 0197 0206 0208 0213
0262 0263 0272 0273 0281 0282 0297 0298 0306 0307 0318 0319
0329 0339 0340 0355 0358 0360 0367 0372 0380 0381 0387 0388
0399 0408 0410 0417 0418 0766 0778 0786 0801 0807 0818 0830
0832 0846 0903 0907 0911 0923 0962 0964 0981 0988 0996 1011
1037 1058 1062 1191 1230 1249 1324 1325 1346 1392 1414 1434
1453 1456 1483 1498 1501 1520 1535 1543 1549 1567 1570 1582
1633 1641 1646 1659 1662 1683 1685 1693 1709 1714 1738 1746
1752 1766 1774 1789 1796 1800 1810 1812 1815 1820 1824 1828
1833 1839 1875 1897 1923 1959 1976 1982 1990 2002 2013 2026
2039 2047 2082 2087 2092 2095
DAT 0322 0409 0466 1916 2330
DCS 1053 3243

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 8

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

OPERATOR MSN
DKH 2975 3027 3234 3268 3368 3485 3596 3605 3967 3984 4064 4102
4154 4276 4401 4429 4573 4587 4652 4833 4840 4981 5013 5070
5071 5131 5226 5329 5339 5455 5491 5674 5737 5876
DLH 0069 0070 0071 0072 0078 0083 0086 0093 0094 0104 0110 0111
0116 0161 0162 0172 0202 0216 0412 0458 0468 0473 0474 0484
0493 0502 0505 0518 0560 0563 0564 0567 0595 0609 0610 0616
0623 0627 0636 0641 0651 0652 0679 0689 0692 0694 0699 0700
0717 0723 0729 0738 0744 0853 0860 0875 0887 0901 1080 1161
1188 1260 1273 1337 1365 1367 3265 3339 3360 3387 3434 3592
3625 3864 3936 3987 4005 4016 4047 4054 4073 4085 4097 4120
4141 4153 4182 4191 4261 4289 4324 4332 4360 4363 4398 4449
4455 4511 4545 4560 4585 4607 4626 4672 4710 4753 4792 4796
4819 4841 4881 4916 4976 4994 5028 5049 5087 5186 5203 5239
5284 5293 5413 5425 5441 5487 5694 5741 5769 5831 5935 5972
6006 6033 6092 6141
DNU 0113
DQA 2347 2599
DRK 2306 2346
DTR 0444 0447 2102
EAF 0424
EDW 0942 0947 1026 1951 2024 2134
EIN 0926 1023 1094 1242 1394 1443 2191 2206 2217 2250 2256 2272
2294 2364 2374 2399 2409 2411 2432 2486 2542 2583 2635 3129
3174 3318 3345 3501 3755 3781 3789 3823 3857 4572 4634 4678
4715
ELB 1703 3705
ERN 1362 2044
ESW 3513
ETD 0350 1947 1955 2167 3004 3050 3676 3693 3713 3902 4066 4077
4124 4934 5095 5348 5407 5714 5791 5821 5836 5882 5924 6108
6134 6143
ETJ 0428
EVA 3363 3886 5261 5328 5354 5377 5485 5792 5808 5849 6024 6042
6087
EVE 5642
EWE 4227 4256
EWG 5497 5525 5557 5601 5635 5658

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 9

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

OPERATOR MSN
EZY 2037 2043 2050 2053 2062 2120 2170 2181 2184 2245 2289 2300
2353 2360 2370 2385 2402 2412 2463 2471 2477 2481 2492 2495
2503 2512 2514 2527 2528 2538 2565 2578 2605 2636 2646 2677
2681 2691 2715 2727 2735 2742 2744 2754 2765 2769 2777 2779
2782 2795 2803 2812 2818 2827 2829 2854 2860 2866 2873 2884
2923 2946 2959 3003 3036 3041 3053 3059 3061 3082 3088 3090
3118 3122 3134 3137 3176 3184 3411 3413 3426 3432 3442 3466
3537 3544 3555 3569 3571 3608 3634 3675 3683 3702 3720 3735
3742 3746 3754 3763 3774 3788 3799 3805 3808 3810 3824 3843
3844 3845 3854 3871 3888 3909 3913 3922 3946 3953 3975 3979
3991 4006 4012 4014 4034 4040 4048 4056 4069 4076 4080 4087
4125 4129 4132 4157 4179 4196 4219 4233 4234 4250 4286 4313
4327 4380 4385 4418 4425 4427 4437 4444 4451 4554 4556 4588
4591 4624 4635 4636 4640 4646 4667 4676 4680 4693 4705 4708
4717 4721 4740 4744 4749 4778 4781 4785 4787 4837 5019 5020
5046 5052 5056 5064 5104 5111 5113 5116 5138 5146 5150 5187
5201 5224 5236 5249 5289 5318 5319 5542 5592 5638 5688 5702
5739 5757 5785 5927 5981 6011 6047 6095
F2I 0082 0085 0099 0138 0148 0168 0203 0220 0230 0239 0243 0249
0251 0285 0294 0301 0317 0342 0347 0386 0422 0449 0460 0488
0496 0497 0525 0532 0538 0540 0555 0573 0642 0653 0657 0724
0758 0787 0793 0814 0976 1010 1018 1256 1846 2103 2137 2308
3853 3872
FCB 0928 2032 2662 2875 2920 3259
FFT 1515 1615 1781 1806 1860 1980 1997 2010 2012 2019 2198 2209
2406 2448 2483 2518 2695 2806 2836 2857 3205 3389 3431 4127
4204 4253 4254 4272 4307 4668 4688 4704 4745 5526 5581 5661
FHY 2524 2804 3025 3852 3891 4207 4658 5096
FIA 1618 3581
FIN 0941 0961 1073 1107 1184 1185 1241 1309 1352 1364 1405 1470
1544 1588 1712 1913 1978 1989 2065 2124 2146 2154 2208 2266
5758 5803 5922 5961 6083
FJW 2281
FLI 3905 5079
FRN 0647 0660
FTZ 2268
G4I 1157 1795 2507
G8E 2141
GAF 1212 1214 3897 4060
GAP 3087 3187 3273 3310 3455 3731 4777 4984 5007 5012 5103 5310
GBB 0053 0054 0064 0067 0076 0077 0081
GCA 0415
GCR 2338 2475 4600 4739 4825 5006 5117 5264 5341 5760 5799 5835
5850 5853 5894 5928 5971
GFA 4030 4059 4083 4146 4158 4188 4218 4255 4502 4541 4780 4827
4860 4865 5025 5074 5171 5175 5180 5257 5321 5336
GLG 1882 2078 3408 3467 3518 4100 4379 4487 4547
GMI 0970 0995 1886 1925 3019 3407 3533 3560 3950 4268 4663 4691
5085 6005

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 10

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

OPERATOR MSN
GOW 3063 3306 3597 3616 3798 3827 3900 3915 3972 5016 5112 5232
5463 5552 5675 5809 5811 5990 6072
GSW 0684 3589 3818 5843
GWI 0117 0135 0137 0200 0201 0209 0217 0218 0267 0268 0269 0346
0382 0401 0646 0654 0794 1016 1077 1084 1089 1136 1147 1155
1170 1172 1209 1277 2607 2628 2632 2813 2833 2976 3011 3128
3172 3193 3352 3358 3375 3500 3534 3839 3841 4166 4285 4998
5043 5457 5467 5535 5569 5941 5978
GWR 1296
GZQ 1878
HDA 0633 0756 0784 0812 0930 0993 1024 1253 1695 1721 1984 2021
2229 2238 2428 3369 3669 4023 4247 5024 5030 5362 5429
HFY 1004
HKE 2299 2322 2717 4181 4445 5685 5725 5738 6142
HKJ 2706 3073 4878
HTU 5209 5240 6156
HVN 2255 2261 2267 2303 2480 2974 3005 3013 3022 3198 3315 3355
3600 3737 3862 3964 3966 4136 4213 4277 4311 4315 4669 4703
4737 4783 4826 4863 4945 4971 5164 5241 5247 5251 5275 5297
5306 5340 5385 5392 5418 5427 5438 5456 5469 5495 5555 5699
5709 5916 5958 5994
HYP 1654 1679 1753
I2L 0491 0519 0556 0668
I2T 1631 1682
IAW 4044 4067
IBE 0938 0998 1021 1027 1154 1516 1572 1655 1674 1681 1716 1793
1809 1836 2220 2225 2242 2248 2264 2311 2365 2391 2472 2488
2736 2756 2843 2889 2897 2996 3078 3209 3320 3380 3443 3651
3744 5486 5570 5692
IBS 1047 1059 1067 1099 1101 1119 1125 1198 1439 1450 1736 2104
2143 2357 2381 2563 2807 5501 5590 5729 5815
IGO 1767 1920 2108 2204 2275 2334 2359 2405 2457 2482 2584 2649
2712 2914 3264 3308 3330 3357 3414 3453 3457 3497 3541 3618
3750 3782 3863 3943 4008 4113 4156 4216 4312 4328 4384 4399
4438 4481 4488 4506 4518 4535 4552 4603 4609 4614 4630 4637
4752 4757 4762 4812 4813 4818 4868 4888 4918 4947 4954 4965
4973 5027 5036 5073 5076 5080 5090 5092 5094 5120 5155 5158
5188 5190 5194 5228 5230 5231 5259 5262 5291 5298 5313 5335
5365 5375 5411 5426 5437 5449 5460 5473 5476 5507 5537 5577
5641 5676 5683 5712 5727 5744 5807 5829 5893 5898 5923 5952
5992 6010 6036
IND 0343
IRA 0303 0312 0345 0575 0857 2054
IRC 0354 0376 0414 0430 0476 0480
IRM 0550
ISR 4354 4413
ISS 0737 0749
IYE 4653 4690

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 11

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

OPERATOR MSN
IZG 0311 0395 0400 0407 0426 0644 0999 1977 2055
JAD 2764 3246
JAS 5478
JAV 0029 0537 2061 2718
JBU 1123 1156 1173 1235 1240 1257 1270 1280 1302 1327 1398 1446
1452 1506 1528 1546 1557 1610 1650 1705 1739 1784 1785 1849
1861 1898 1904 1915 1917 1927 1948 2006 2020 2031 2042 2063
2075 2099 2125 2132 2136 2149 2150 2159 2160 2177 2201 2215
2231 2246 2259 2280 2284 2286 2307 2314 2336 2352 2368 2384
2386 2415 2447 2449 2461 2489 2491 2504 2520 2535 2577 2580
2640 2647 2671 2710 2725 2755 2781 2802 2814 2832 2848 2871
2880 2900 2945 2970 2977 2992 3029 3039 3072 3091 3119 3150
3190 3228 3263 3287 3348 3381 3416 3451 3479 3488 3517 3554
3572 3622 3659 3707 3724 3760 3800 3811 4578 4612 4647 4904
5060 5142 5148 5302 5312 5349 5417 5677 5723 5782 5783 5854
5865 5909 5960 6031 6130
JBW 0445 0535
JJP 5093 5145 5161 5245 5274 5281 5355 5492 5499 5520 5598 5618
5649 5695 5701 5717 5732 5796 5885
JSA 2316 2356 2423 2453 2604 4443 4515 4772 4786 4872 4914 5305
5323 5390 5433 5472 5708 5813
JST 1195 1408 2169 2185 2197 2292 2329 2455 2515 2526 2537 2573
2608 2642 2651 2703 2766 2787 3474 3495 3668 3717 3783 3899
3916 3917 3948 4177 4178 4229 4245 4257 4303 4343 4356 4434
4460 4466 4495 4497 4527 4899 4922 5039 5211 5270 5311 5334
5482 5489 5532 5566 5631 5775 5780 5814 5858 5871
JZR 3919 3939 4162 5033 5625 5833 6124
KAC 0181 0182 0195 2046 3957
KAY 3046 4470 5963
KFR 2650
KHO 0937 2957 2965
KHV 5343
KKK 0604 0614 0675 0761 0806 0808 0823 0963 0968 0974 1008 1124
1390 1438 1451 1503 1624 1950 1953 2029 2077 2747 2753 5115
5290 5464
KNE 1866 1872 1942 1965 2171 2182 2199 2569 2776 3218 3238 3256
3361 3396 3425 3475 3530 3787 3802 3809 3817 3868 3889 3894
3933 4055 4061 4699 4735 5716
KZR 1042 1204 3141 3614 5357 5401 5404 5613 5734 5870 5968 6029
6037
LAA 4405 4490 4526 5373 5405 5494
LAN 1304 1332 1351 1355 1491 1512 1526 1548 1568 1854 1858 1877
1903 2089 2096 2295 2304 2321 2572 2585 2845 2858 2864 2872
2886 2892 2894 3280 3319 3535 3556 3663 3671 3770 3772 3779
4383 4400 4439 4476 4509 4516 4543 4546 4549 4576 4597 4598
4605 4657 4697 4839 4871 4892 4896 4921 4943 4972 5005 5097
5125 5178 5213 5229 5234 5263 5316 5324 5364 5408 5443 5453
5483 5493 5548 5554 5583 5586 5654 5666 5686 5707 5748 5764
5801 5818 5859 5929 5965 6135

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 12

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

OPERATOR MSN
LAO 4596 4639 5356 5396
LBT 1121 1175 1597 1744 2158 3480 3487 4623
LFO 0659
LJB 3985
LKE 2581 2617 2746 3240 5100 5172 5220 6105 6149
LKH 0883
LLC 0914 0967 0990 1041 1715 2987 4203 4489
LLM 1918 1956 1967 1969 1993 2337 2413 2419 2439 2571 2688
LLP 0739 1007 1411 1723 2016 2118 2342 2903 2912 3191
LLX 1054 2529 2619
LMJ 1868
LMU 0852 0977 1561
LUR 0229 0726
LWA 2878 2954
LZB 2540 2596 3309 3564 3780
MAC 4539 4568 4806 4848 5143 5206
MAU 1592 1936
MEA 3736 3804 3837 4296 4339 4632 5000 5152 5162 5253 5746
MGF 0308
MJF 3402 4353
MJN 3723 4117 4795
MLD 0622 0741 1786 2849
MLM 4622
MMA 0973 1180 1247 1791
MON 0864 0983 1015 1045 1153 1207 1320 1413 1421 1571 1605 1637
1707 1763 1794 1941 2105 2142 2234 2553 2610 2730 2793 3278
3293 3458 3522 3546 3575 5582 5606 6059 6126
MOV 2442 2446 3364 3403
MRJ 0530 1202 1300 1353
MSC 2094 2937 2966 3282 3323 3626 3840
MSR 0165 0166 0178 0194 0198 0351 0366 0680 0687 0715 0725 2070
2073 2079
MXA 0252 0260 0275
MYX 0888 0936 0984 1183 1896
NIA 2410 2476 2874 3183 3219 3925 4310
NKS 2433 2470 2473 2485 2490 2560 2567 2590 2603 2622 2673 2679
2698 2704 2711 2723 2797 2893 2898 2929 2942 2963 2978 2983
3007 3017 3026 3165 3393 3395 4206 4264 4321 4403 4422 4431
4548 4592 4595 4902 4951 4996 5029 5042 5132 5159 5370 5387
5458 5517 5624 5672 5804 5861 5880 5954 5999 6082
NLY 1629 1966 1988 1994 2005 3504 3708 3749 4334 4728 5038 5126
5133
NMA 1697 1732 1952 2676
NMB 3346 3586 5366 5400
NSS 1589
NVD 0211 0528 0558 0561 0709 0827 0828 0902 1005 1366 1626 1778
1998 2115

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 13

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

OPERATOR MSN
NVR 2216
NWS 1219 1233 3034 3106 3120
OBS 3758
OHY 0364 0385 0543 0580 0640 0661 0676 0771 0792 0810 0811 0835
0912 0916
OLY 0427 0666 1060 1612 2396
OMS 3035 3047 3111
ONE 3001 3030 3062 3214 3371 3390 3438 3469 3509 3585 3602 3606
3642 4222 4287 4336 4891 4913 4941 4942 5193 5278 5299 5754
5841 6050 6057 6103 6110 6125 6139
ORF 2566 4992
OTF 1407 2479
OZW 0429 1922
PAL 3553 3579 3652 5081 5140 5315 5371 5715 5747 5787 5820 5825
5838 6074
PGT 3831 4175 5879 5902 5950 5995
PIA 2155 2212 2274 2719 2758 2789 2926 2944 3031 3060 3097
PIC 2517 2670 2922 3012 3621 4459 4533 6136
PKZ 6069
PTI 1263 1598 1625
QAF 0927
QDA 6061 6102
QQE 1335 3994 4114 4170 5255
QSM 0607 0611 0617 2091
QTR 1487 1566 1648 1656 1773 1895 1928 1957 2097 2107 2121 2138
2161 2288 2341 3274 4110 4130 4173 4183 4382 4406 4436 4479
4496 4530 4615 4700 4754 4784 4802 4810 4858 4930 4968 5010
5078 5127 5217 5361 5395
R1T 1908 6112
RBA 2135 2139 2195 3071
RBG 3152
RCT 1017
RIH 0438
RJA 2953 3428 3685 3803 3832 4670 4817 4853 5099 5128 5177
RJD 5277
ROT 2931 2955 3220 3225
RWZ 0802 1843 2084 2193 2372 2393
RYW 0569 5367
RZO 2011 2325 2390
SAA 2326 2355 2375 2379 2418 2438 2469 2501 4990 5011 5637 5680
5956 6007 6147
SAI 0542 0877 1497 2027 2404 2414 2452 2496 2502 2631 2655 2738
2739 3105 3270
SAS 1383 1587 1619 1642 1675 1798 1807 1817 1848 2817 2850 2856
2883 2888 2911 2958 2990 3086 3159 3192 3227 3231 3292 3335

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 14

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

OPERATOR MSN
SBI 1071 1078 1090 1091 1126 1131 1149 1164 1167 1819 1870 2028
2064 2076 2279 2369 2373 2464 2474 2618 2641 2726 3070 3446
3473 3490 3494 3866 3880 4032 4150 5001 5026 5031 5106 5134
5167 5559 5607 5779 5919 6066
SDM 0649 1130 1200 1379 1488 1560 1630 1743 1761 1805 1808 1841
1851 1863 1876 1890 2093 2151 2163 2179 2241 2465 2497 2751
2879 2913 3065 3179 3794 3942 3998
SDR 4953 4974
SEK 0357
SEY 1944 1945
SFJ 4555 4720 5102 5393 5512 5652 5773 5862 5931
SFW 0994
SHJ 0910
SHU 2052 2069 2072 2222 2243 3108 3281 3298 3336 3838
SKU 1400 1523 2119 2129 2214 2249 2251 2283 2378 2380 2436 2460
2548 3171 3331
SLK 2252 2568 2775 3104 3570 4118 4215 4259 4457 5050 5089 5296
5531 5794
SND 1880 1999
SNG 4611 4648
SNX 0289
SOL 0302
SSG 1485 2550
SUD 3040
SVA 3932 4057 4081 4090 4092 4104 4115 4122 4135 4273 4314 4337
4349 4357 4364 4376 4391 4392 4393 4394 4397 4408 4414 4419
4432 4442 4454 4467 4484 4501 4517 4519 4542 4564 4577 4590
4811 4823 4838 4925 4955 4962 5009 5065 5223 5285 5314 5447
5509 5549
SVR 0735 0775 0815 0841 0991 1012 1063 1152 1199 1484 1579 1603
1720 1751 1777 1884 1901 1905 2117 2166 2175 2187 2278 2327
2343 2349 2376 2623 2707 2862 2947 2998 3099 3107 3189 3385
3388 3433 3472 3834 5055
SVW 2592 3100 3133 3542 4169
SWM 0421 0986 1293 1909
SWR 0520 0522 0541 0545 0553 0559 0562 0574 0577 0578 0585 0596
0603 0612 0621 0635 0643 0664 0673 0681 0701 0703 0713 0727
0782 0987 1144 4534 4618 4673 5037 5069 5518 5567
SYR 0886 0918 1032 1076 1085 1117
TAE 0934 0946 0949 1339 1368 1500 1934 2659
TAI 1066 1334 2282 2301 2339 2434 2444 2687 2917 3042 3057 3103
3113 3248 3276 3378 3418 3510 3538 3869 4906 4944 5068 5219
5238 5243 5280 5333 5406 5936 6002 6068 6099 6132

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 15

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

OPERATOR MSN
TAM 1092 1096 1103 1139 1143 1158 1215 1246 1251 1376 1459 1486
1518 1575 1580 1591 1593 1595 1628 1652 1692 1801 1802 1825
1826 1827 1831 1832 1835 1837 1855 1857 1888 1891 2014 2513
2734 2737 2784 2838 2859 2887 2896 2904 2924 3002 3032 3058
3156 3180 3211 3222 3229 3266 3284 3294 3313 3391 3565 3588
3595 3630 3658 3662 3710 3727 3733 3761 3816 4000 4163 4171
4192 4320 4352 4358 4389 4441 4446 4465 4544 4563 4570 4662
4734 4756 4773 5066 5101 5107 5184 5222 5342 5345 5528 5591
5621 5643 5749 5752 5845 5883 5947 5987 6097 6121 6163 6165
TAP 0629 0750 0755 0763 0790 0821 0837 0870 0906 0917 0933 0945
0960 0979 0982 1034 1100 1106 1120 1127 1165 1181 1206 1231
1307 1399 1667 1668 1713 1718 1756 1765 1799 1816 2178 2270
2792 2822 3769 3883 4021 4095 4106 4145 4742
TAR 0123 0124 0205 0370 0390 0402 0511 0869 0880 0958 0975 1187
1479 1700 3096 4344 4689 5204 5474 5610
TBA 4766 4801 4846 5157 5256 5451 5529 5563 5855
TBZ 0361 0362 0405
TCW 1381 1402 1954
TCX 1006 1238 1250 1881 1887 1921 1972 2060 5603 5872 6038 6056
6114 6122
TDR 0795
TGW 2724 2728 3757 3801 4210 4421 4469 4491 4493 4532 4561 4608
4645 4879 4931 5496 5596 5605 5662 5697 5721 5805 5915
THA 5553
THD 5198 5248 5258 5301 5436 5806 5828 5857 5892 5951 5979 6113
6140
THY 1002 2156 2164 2395 2401 2522 2602 2609 2626 2823 2868 2916
2919 2928 2934 2984 2999 3010 3015 3126 3142 3185 3207 3208
3239 3257 3283 3303 3341 3350 3382 3405 3429 3525 3539 3558
3567 3603 3637 3654 3673 3688 3718 3719 3738 4042 4629 4643
4654 4665 4682 4695 4698 4706 4755 4761 4774 4779 4788 4790
5077 5083 5118 5154 5205 5254 5388 5450 5465 5490 5546 5584
5633 5663 5667 5689
TJS 3632
TNA 0731 0746 0791 0822 6009
TTW 4804 4874
U6A 0733
UAE 4822

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 16

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

OPERATOR MSN
UAL 0435 0439 0442 0450 0452 0454 0456 0457 0462 0463 0464 0465
0470 0472 0475 0479 0483 0485 0487 0489 0500 0503 0504 0506
0508 0510 0512 0523 0539 0568 0571 0587 0589 0592 0613 0638
0655 0678 0683 0686 0690 0702 0748 0751 0759 0780 0783 0788
0798 0804 0820 0824 0825 0826 0834 0836 0842 0843 0847 0850
0851 0858 0862 0865 0867 0871 0873 0882 0893 0898 0944 0948
0952 0955 0965 0980 0989 1001 1022 1031 1104 1105 1128 1146
1163 1192 1211 1243 1248 1266 1272 1282 1290 1291 1321 1341
1343 1359 1363 1401 1409 1420 1426 1427 1432 1435 1460 1469
1474 1475 1477 1495 1507 1508 1514 1522 1533 1538 1545 1555
1559 1569 1573 1581 1584 1585 1586 1600 1609 1617 1620 1627
1647 1649 1653 1664 1669 1671 1680 1688 1702 1728 1731 1737
1741 1755 1821 1840 1842 1845 1847 1865 2667 2680 2714 2815
2901 2940 2948 2969 3020 3144 3258
UEA 2654 2696 2762 2774 2820 2835 3024 3706 4347 4743 4988 5003
5191 5252 5957
UJX 1213 1663
UKN 3260
UNA 2921 4228 4583 4732 5545
USA 0066 0448 0762 0803 0844 0856 0861 0863 0866 0868 0885 0889
0890 0896 0904 0922 0924 0929 0931 0953 0972 0997 1003 1019
1033 1038 1040 1043 1046 1049 1050 1051 1052 1055 1056 1061
1064 1065 1069 1075 1079 1083 1088 1095 1097 1109 1110 1111
1112 1114 1116 1122 1134 1135 1141 1148 1166 1178 1182 1196
1203 1205 1223 1224 1234 1245 1254 1264 1265 1268 1269 1274
1275 1281 1284 1287 1289 1294 1297 1298 1301 1310 1311 1313
1314 1315 1317 1319 1323 1326 1328 1331 1340 1342 1348 1350
1354 1358 1360 1369 1371 1373 1375 1378 1382 1389 1391 1393
1395 1397 1403 1406 1410 1412 1417 1419 1425 1431 1436 1442
1447 1455 1462 1463 1465 1472 1481 1490 1492 1496 1499 1517
1519 1521 1525 1527 1531 1534 1536 1539 1547 1552 1563 1565
1576 1621 1643 1644 1651 1666 1701 1704 1710 1724 1764 1792
1844 1935 2302 2312 2458 2570 2595 2613 2615 2630 2669 2690
3584 3629 3633 3712 3740 3796 3858 3879 3881 3924 3928 3944
3960 3977 3989 3993 4025 4041 4050 4082 4086 4107 4123 4134
4149 4202 4242 4843 4847 4850 4885 4893 4898 4932 4935 4940
4957 4960 4966 5235 5244 5269 5282 5292 5300 5317 5332 5368
5374 5409 5422 5444 5475 5504 5513 5588 5594 5644 5659 5684
5696 5728 5751 5763 5795 5800 5899 5939 5980 6027 6035 6100
6133 6152
UZB 4371 4395 4417 4485 4492 4528 4651 4724 4770 4952
VAW 0879
VIP 2421 4151
VIV 2157 2210 2443 2576 2661 2752 2908 3743
VJC 2745 3646 3739 3791 4049 4190 4193 4415 4475 4504 4512 4907
5295 5742 5822 6025
VKG 1932 1960

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 17

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

OPERATOR MSN
VLG 1208 1221 1349 1396 1430 1461 1550 1749 1862 1914 1933 2168
2223 2388 2407 2589 2620 2658 2678 2761 2785 2794 2798 2962
2988 3028 3054 3083 3095 3102 3109 3145 3151 3169 3203 3237
3321 3376 3377 3400 3444 3476 3492 3529 3833 3907 4463 4478
4661 4674 4681 4849 4855 4937 5479 5530 5533 5587 5599 5612
5616 5620 5673 5877 5925 5940 6039 6045 6079 6081 6123 6128
VNL 5844 5901 5926
VOE 1684 2113 2122 2240 2253 2258 2318 2332 2382
VOI 2657 2666 2771 2780 2979 2997 3045 3069 3077 3175 3253 3279
3450 3463 3491 3524 3543 3590 3624 4741 4798 4828 4832 4950
5062 5207 5212 5308 5322 5337 5391 5488 5510 5595 5651 5776
5793 5819 5988 5996 6014 6109 6161
VRD 2616 2674 2740 2773 2778 2800 2811 2830 2851 2993 3016 3037
3101 3135 3155 3181 3204 3230 3324 3347 3349 3359 3398 3417
3445 3460 3465 3503 3656 3670 3684 3686 4448 4480 4558 4559
4610 4616 4655 4805 4814 4851 4867 4894 4948 4959 4991 4999
5004 5034 5058 5179 5515
VRE 1429 2066 2126 2213 2228
VVC 1306 1370 1454 1564 1578 1657 1686 1725 1757 1867 2123 3896
3931 3949
WAN 6080 6166
WHT 0548 2440 2675
WOW 4270 4305 5681 5733
WRC 1869 2462 2682
WZZ 3127 3143 3166 3177 3354 3384 3409 3430 3531 3562 3741 3771
3807 3877 3927 3947 3968 4109 4174 4223 4246 4308 4323 4351
4372 4621 4628 4683 4716 4736 5021 5075 5123 5139 5196 5539
5604 5608 5615 5617 5660 6001 6058 6077 6086 6093 6098 6115
6131

(4) Configuration by MSN

MSN CONFIGURATION
0029 0052 0067 0076 0081 0087 0123 0124 0142 0181 0182 001 002
0195 0203 0205 0211 0220 0229 0249 0252 0253 0259 0260
0275 0276 0279 0289 0290 0294 0296 0301 0302 0303 0308
0311 0312 0314 0320 0321 0322 0332 0342 0347 0353 0354
0357 0361 0362 0368 0370 0373 0376 0386 0390 0400 0402
0405 0406 0407 0414 0415 0422 0426 0428 0430 0447 0460
0480 0511 0527
0045 0046 0049 0050 0051 0056 0057 0398 0416 0423 0431 008
0432 0486 0490 0499

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 18

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

MSN CONFIGURATION
0053 0054 0055 0059 0064 0065 0066 0068 0069 0070 0071 002
0072 0073 0077 0078 0082 0083 0084 0085 0086 0093 0094
0099 0104 0110 0111 0112 0113 0115 0116 0117 0118 0121
0122 0125 0126 0127 0135 0137 0138 0140 0141 0148 0149
0150 0152 0153 0154 0157 0159 0160 0161 0162 0165 0166
0171 0172 0174 0175 0178 0183 0185 0192 0194 0197 0198
0200 0201 0202 0206 0208 0209 0210 0213 0216 0217 0218
0219 0230 0231 0232 0234 0237 0239 0242 0243 0248 0251
0254 0255 0256 0262 0263 0265 0267 0268 0269 0272 0273
0277 0281 0282 0284 0285 0287 0291 0292 0293 0297 0298
0300 0306 0307 0309 0316 0317 0318 0319 0324 0325 0328
0329 0330 0331 0339 0340 0341 0343 0345 0346 0350 0351
0355 0358 0360 0366 0367 0371 0372 0378 0380 0381 0382
0387 0388 0393 0395 0399 0401 0403 0404 0408 0409 0410
0417 0418 0420 0421 0424 0427 0429 0435 0436 0438 0439
0441 0442 0444 0445 0448 0449 0450 0452 0454 0456 0457
0462 0463 0464 0465 0466 0470 0472 0475 0476 0479 0482
0483 0485 0487 0489 0491 0496 0497 0500 0501 0503 0504
0506 0507 0508 0510 0512 0523 0525
0164 0168 0169 005 008
0364 0385 0597 0633 0666 0668 003 006
0412 0434 0458 0468 0473 0474 0477 0484 0488 0493 0495 006
0502 0505 0509 0513 0514 0516 0517 0518 0519 0520 0522
0524 0526 0532 0535 0538 0541 0544 0550 0552 0555 0560
0563 0564 0567 0570 0576 0581 0583 0586 0591 0593 0595
0599 0604 0614 0620 0631 0642 0652 0664 0675 0677 0680
0498 002 006
0521 0529 006 016
0528 0530 004 012
0531 0533 0534 0537 0539 0540 0542 0543 0545 0546 012
0548 0549 0551 0553 0554 0556 0559 0562 0565 0566 0568 016
0569 0571 0572 0574 0575 0577 0578 0579 0580 0582 0584
0585 0587 0589 0592 0596 0598 0600 0603 0608 0609 0610
0612 0613 0616 0618 0621 0623 0625 0627 0629 0634 0635
0636 0637 0638 0641 0643 0645 0646 0649 0651 0654 0655
0656 0658 0659 0661 0665 0667 0669 0670 0671 0673 0676
0678 0679 0681 0682 0683 0685
0558 0561 0573 0607 0611 0617 0619 0622 0630 0639 0640 014 016
0644 0647 0648 0650 0653 0657 0660 0662

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 19

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

MSN CONFIGURATION
0672 0686 0688 0689 0690 0691 0693 0694 0695 0696 0697 017
0698 0700 0701 0702 0703 0704 0705 0706 0709 0711 0712
0713 0714 0716 0717 0718 0719 0720 0721 0722 0723 0727
0728 0729 0730 0732 0734 0735 0736 0737 0738 0739 0740
0742 0743 0744 0745 0748 0750 0751 0752 0754 0755 0757
0759 0762 0763 0764 0766 0767 0768 0769 0770 0773 0774
0776 0778 0779 0780 0782 0783 0785 0786 0788 0790 0791
0793 0794 0795 0797 0798 0800 0801 0803 0804 0807 0809
0813 0814 0817 0818 0820 0821 0822 0824 0825 0826 0828
0829 0830 0831 0832 0833 0834 0836 0837 0839 0840 0842
0843 0844 0845 0846 0847 0849 0850 0851 0853 0856 0858
0859 0860 0861 0862 0863 0865 0866 0867 0868 0870 0871
0872 0873 0874 0875 0876 0879 0881 0882 0883 0884 0885
0889 0890 0892 0893 0894 0895 0896 0898 0900 0902 0903
0904 0905 0906 0907 0910 0911 0912 0914 0916 0917 0919
0921 0922 0923 0924 0925 0927 0928 0929 0931 0933 0934
0936 0937 0938 0942 0944 0945 0946 0947 0948 0949 0950
0951 0952 0953 0955 0957 0960 0962 0964 0965 0966 0971
0972 0976 0979 0980 0981 0982 0985 0988 0989 0990 0992
0994 0996 0997 0998 0999 1000 1001 1002 1003 1005 1007
1009 1010 1011 1013 1014 1016 1018 1019 1020 1022 1025
1026 1028 1029 1030 1031 1032 1033 1034 1035 1036 1037
1038 1039 1040 1041 1043 1046 1047 1048 1049 1050 1051
1052 1053 1054 1055 1056 1057 1058 1059 1061 1062 1063
1064 1065 1066 1067 1069 1070 1071 1072 1073 1075 1076
1077 1078 1079 1081 1082 1083 1084 1085 1086 1087 1088
1089 1090 1091 1092 1093 1095 1096 1097 1099 1100 1101
1102 1103 1104 1105 1106 1107 1108 1109 1110 1111 1112
1114 1115 1116 1117 1118 1119 1120 1121 1122 1123 1124
1125 1126 1127 1128 1129 1130 1131 1132 1134 1135 1136
1137 1138 1139 1140 1141 1142 1143 1146 1147 1148 1149
1150 1151 1152 1154 1155 1156 1157 1158 1159 1160 1162
1163 1164 1165 1166 1167 1168 1169 1170 1171 1172 1173
1175 1176 1177 1178 1179 1180 1181 1182 1183 1184 1187
1189 1190 1191 1192 1193 1194 1196 1197 1198 1200 1201
1203 1205 1206 1208 1209 1211 1212
0684 0687 0692 0699 0715 0725 0731 0746 0765 0771 0775 011
0777 0781 0787 0792 0796 0802 0806 0810 0811 0815 0819
0827 0835 0841 0848 0852 0855 0864 0878 0887 0891 0901
0915 0920 0926 0935 0940 0941 0959 0961 0963 0968 0974
0983 0987 0991 0993 0995 1004 1006 1008 1012 1015 1017
1021 1023 1024 1027 1042 1045 1060 1080 1094 1133 1144
1153 1161 1174 1185 1188 1195 1199 1202 1204 1207
0724 0726 0733 0741 0749 0756 0758 0760 0784 0805 0812 015 017
0816 0838 0854 0857 0869 0877 0880 0886 0888 0897 0909
0913 0918 0930 0932 0939 0943 0958 0967 0973 0975 0977
0984 0986
0761 0808 0823 0908 0970 007 011

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 20

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

MSN CONFIGURATION
1210 1213 1215 1216 1217 1221 1222 1223 1224 1225 1226 018
1228 1229 1230 1231 1232 1234 1235 1236 1237 1239 1240
1242 1243 1244 1245 1246 1247 1248 1249 1251 1252 1253
1254 1255 1256 1257 1258 1259 1261 1262 1263 1264 1265
1266 1267 1268 1269 1270 1271 1272 1274 1275 1277 1279
1280 1281 1282 1283 1284 1285 1286 1287 1288 1289 1290
1291 1292 1294 1295 1296 1297 1298 1300 1301 1302 1303
1304 1306 1308 1309 1310 1311 1312 1313 1314 1315 1316
1317 1318 1319 1320 1321 1322 1323 1324 1325 1326 1327
1328 1329 1330 1331 1332 1334 1335 1336 1337 1338 1339
1340 1341 1342 1343 1344 1345 1346 1347 1348 1349 1350
1351 1352 1353 1354 1355 1357 1358 1359 1360 1361 1362
1363 1364 1365 1367 1368 1369 1370 1371 1372 1373 1375
1376 1377 1378 1379 1380 1381 1382 1383 1384 1385 1386
1387 1388 1389 1390 1391 1392 1393 1394 1395 1396 1397
1398 1400 1401 1402 1404 1405 1406 1407 1409 1410 1411
1413 1414 1415 1416 1418 1419 1420 1422 1423 1424 1426
1427 1429 1430 1432 1434 1435 1437 1439 1440 1441 1443
1444 1445 1446 1448 1449 1450 1452 1453 1454 1456 1457
1459 1460 1461 1463 1466 1467 1468 1469 1470 1471 1473
1474 1475 1477 1478 1479 1480 1482 1483 1484 1485 1486
1488 1489 1490 1491 1493 1494 1495 1497 1498 1500 1501
1502 1504 1505 1506 1507 1508 1509 1510 1512 1513 1514
1515 1516 1518 1520 1522 1523 1524 1526 1527 1528 1529
1530 1532 1533 1534 1535 1537 1538 1540 1541 1542 1543
1544 1545 1546 1547 1548 1549 1550 1551 1552 1553 1555
1556 1557 1558 1559 1560 1561 1562 1563 1564 1565 1566
1567 1568 1569 1570 1571 1573 1574 1575 1576 1577 1578
1579 1580 1581 1582 1583 1584 1585 1586 1588 1589 1590
1591 1592 1593 1594 1595 1597 1598 1599 1600 1601 1603
1604 1605 1606 1609 1610 1612 1613 1615 1616 1617 1618
1620 1621 1622 1624 1625 1626 1627 1628 1630 1631 1633
1634 1635 1637 1639 1640 1641 1643 1644 1645 1646 1647
1648 1649 1650 1652 1653 1654 1655 1656 1657 1659 1661
1662 1663 1664 1665 1667 1668 1669 1671 1672 1673 1674
1677 1678 1679 1680 1682 1683 1684 1685 1686 1687 1688
1689 1692 1693 1694 1696 1697 1699 1700 1702 1703 1705
1706 1708 1709 1710 1712 1714 1715 1717 1718 1719 1721
1722 1723 1725 1728 1730 1731 1732 1733 1735 1736 1737
1738 1739 1740 1741 1742 1743 1744 1745 1746 1747 1749
1750 1751 1752 1753 1754 1755 1756 1757 1758 1759 1760
1761 1762 1764 1765 1766 1767 1769 1770 1771 1773 1774
1775 1777 1778 1779 1780 1781 1782 1784 1785 1786 1787
1789 1790 1791 1792 1793 1795 1796 1797 1799 1800 1801
1802 1803 1804 1805 1806 1808 1809 1810 1812 1814 1815
1816 1818 1819 1820 1821 1823 1824 1825 1826 1827 1828
1829 1831 1832 1833 1834 1835 1837 1838 1839 1840 1841
1842 1844 1845 1846 1847 1849 1851 1852 1853 1854 1855
1856 1857 1858 1860 1861 1862 1863 1864 1865 1866 1867

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 21

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

MSN CONFIGURATION
1868 1870 1871 1872 1873 1874 1875 1876 1877 1879 1880 018
1882 1883 1884 1885 1886 1888 1889 1890 1891 1892 1893
1894 1895 1896 1897 1898 1899 1900 1901 1902 1903 1904
1906 1907 1908 1909 1910 1911 1912 1913 1914 1915 1916
1917 1918 1920 1922 1923 1924 1925 1927 1929 1931 1933
1934 1935 1936 1937 1938 1940 1942 1943 1944 1945 1947
1948 1949 1951 1952 1954 1955 1957 1958 1959 1961 1962
1963 1964 1965 1968 1969 1971 1973 1975 1976 1979 1980
1981 1982 1983 1986 1987 1989 1990 1993 1996 1997 1998
1999 2000 2001 2002 2003 2004 2006 2007 2008 2009 2010
2011 2012 2013 2014 2015 2016 2018 2019 2020 2022 2023
2024 2026 2027 2028 2029 2030 2031 2032 2033 2034 2035
2036 2037 2038 2039 2040 2042 2043 2044 2046 2047 2048
2049 2050 2052 2053 2054 2056 2057 2059 2061 2062 2063
2065 2066 2068 2069 2070 2071 2072 2073 2074 2075 2077
2078 2079 2081 2082 2083 2084 2085 2086 2087 2089 2090
2091 2092 2093 2094 2095 2096 2097 2098 2099 2100 2101
2102 2103 2104 2106 2108 2109 2112 2113 2114 2116 2118
2119 2120 2121 2122 2123 2124 2125 2126 2127 2129 2130
2131 2132 2133 2134 2135 2136 2137 2138 2139 2140 2141
2142 2143 2144 2145 2146 2147 2148 2149 2150 2151 2152
2153 2154 2155 2156 2157 2158 2159 2160 2161 2162 2163
2164 2165 2166 2167 2168 2169 2170 2171 2172 2173 2174
2175 2176 2177 2178 2179 2180 2181 2182 2183 2184 2185
2186 2187 2188 2189 2191 2192 2193 2194 2195 2196 2197
2198 2199 2200 2201 2202 2203 2204 2205 2206 2207 2209
2210 2212 2213 2214 2215 2217 2219 2221 2222 2223 2224
2225 2227 2228 2229 2230 2231 2232 2233 2235 2236 2237
2238 2239 2240 2241 2242 2243 2244 2245 2246 2248 2249
2250 2251 2252 2253 2254 2256 2257 2258 2259 2260 2262
2263 2264 2265 2266 2268 2269 2271 2272 2273 2274 2275
2277 2278 2279 2280 2281 2282 2283 2284 2285 2286 2287
2288 2289 2291 2292 2293 2294 2295 2296 2297 2298 2299
2300 2301 2302 2304 2306 2307 2308 2310 2311 2312 2313
2314 2316 2317 2318 2319 2321 2322 2325 2326 2327 2328
2329 2331 2332 2333 2334 2335 2336 2338 2339 2340 2341
2343 2344 2345 2346 2347 2348 2349 2350 2352 2353 2354
2355 2356 2358 2359 2360 2361 2362 2364 2365 2366 2367
2368 2369 2370 2371 2372 2373 2374 2375 2376 2377 2378
2379 2380 2382 2383 2384 2385 2386 2387 2388 2389 2390
2391 2392 2393 2394 2395 2396 2397 2398 2399 2400 2401
2402 2403 2404 2405 2406 2407 2408 2409 2411 2412 2413
2414 2415 2416 2417 2418 2419 2420 2421 2422 2423 2425
2426 2427 2428 2429 2430 2431 2432 2433 2434 2435 2436
2437 2438 2439 2440 2441 2442 2443 2444 2445 2446 2447
2448 2449 2450 2451 2452 2453 2454 2455 2456 2457 2458
2459 2460 2461 2463 2464 2465 2466 2467 2468 2469 2470
2471 2473 2474 2475 2477 2478 2479 2481 2482 2483 2484
2485 2486 2487 2489 2490 2491 2492 2493 2494 2495 2496
2497 2498 2499 2501 2502 2503 2504 2505 2506 2507 2508
2509 2510 2511 2512 2513 2514 2515 2516 2517 2518 2519

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 22

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

MSN CONFIGURATION
2520 2522 2523 2524 2525 2526 2527 2528 2529 2531 2532 018
2533 2534 2535 2537 2538 2539 2540 2541 2542 2544 2545
2546 2547 2548 2550 2551 2552 2554 2555 2556 2557 2558
2559 2560 2561 2562 2564 2565 2566 2567 2568 2569 2570
2571 2572 2573 2574 2575 2576 2577 2578 2579 2580 2581
2582 2583 2584 2585 2586 2587 2588 2589 2591 2592 2593
2594 2595 2596 2597 2598 2600 2601 2602 2603 2604 2605
2606 2607 2608 2609 2611 2612 2613 2614 2615 2616 2617
2618 2619 2620 2621 2622 2623 2624 2625 2626 2627 2628
2629 2630 2631 2632 2633 2634 2635 2636 2637 2638 2639
2640 2641 2642 2643 2644 2645 2646 2647 2648 2649 2650
2651 2652 2654 2655 2656 2657 2658 2659 2660 2661 2662
2663 2664 2665 2666 2667 2668 2669 2670 2671 2672 2673
2674 2675 2676 2677 2678 2679 2680 2681 2683 2684 2685
2686 2688 2689 2690 2691 2692 2693 2694 2695 2696 2697
2698 2699 2700 2701 2702 2703 2704 2705 2706 2708 2709
2710 2711 2712 2714 2715 2716 2717 2718 2719 2720 2721
2723 2724 2725 2727 2728 2729 2731 2732 2733 2734 2735
2737 2738 2739 2740 2742 2743 2744 2745 2746 2747 2748
2749 2750 2751 2752 2753 2754 2755 2757 2758 2760 2761
2762 2763 2764 2765 2766 2768 2769 2770 2771 2772 2773
2774 2775 2776 2777 2778 2779 2780 2781 2782 2783 2784
2785 2786 2787 2788 2789 2790 2791 2792 2794 2795 2796
2797 2798 2800 2801 2802 2803 2804 2805 2806 2807 2808
2810 2811 2812 2813 2814 2815 2816 2817 2818 2819 2820
2821 2822 2824 2825 2826 2827 2828 2829 2830 2831 2832
2833 2834 2835 2836 2837 2838 2839 2840 2841 2842 2843
2844 2845 2846 2847 2848 2849 2850 2851 2852 2853 2854
2855 2856 2857 2858 2859 2860 2861 2863 2864 2865 2866
2867 2869 2870 2871 2872 2873 2874 2875 2876 2877 2878
2879 2880 2881 2883 2884 2885 2886 2887 2888 2889 2890
2892 2893 2894 2896 2897 2898 2899 2900 2901 2902 2904
2905 2906 2907 2908 2909 2910 2911 2913 2914 2915 2917
2918 2920 2921 2922 2923 2924 2925 2926 2928 2929 2930
2931 2932 2934 2935 2937 2938 2939 2940 2942 2943 2944
2945 2946 2947 2948 2949 2950 2951 2952 2953 2954 2955
2956 2958 2959 2960 2961 2962 2963 2964 2966 2967 2968
2969 2970 2972 2973 2975 2976 2977 2978 2979 2980 2981
2982 2983 2984 2985 2986 2987 2988 2989 2990 2991 2992
2993 2994 2995 2997 2998 3000 3001 3002 3003 3004 3006
3007 3008 3009 3011 3017 3019

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 23

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

MSN CONFIGURATION
1214 1219 1220 1227 1233 1238 1241 1250 1260 1273 1276 009
1293 1299 1307 1356 1366 1399 1403 1408 1412 1417 1421
1425 1428 1431 1433 1436 1438 1442 1447 1451 1455 1458
1462 1465 1472 1476 1481 1487 1492 1496 1499 1503 1511
1517 1519 1521 1525 1531 1536 1539 1554 1572 1587 1596
1602 1607 1611 1614 1619 1623 1629 1632 1636 1638 1642
1651 1658 1666 1670 1675 1681 1690 1691 1695 1701 1704
1707 1711 1713 1716 1720 1724 1726 1734 1748 1763 1772
1776 1783 1788 1794 1798 1807 1811 1817 1836 1843 1848
1850 1859 1869 1878 1881 1887 1905 1921 1926 1928 1932
1941 1946 1950 1953 1956 1960 1966 1967 1970 1972 1974
1977 1978 1984 1988 1994 1995 2005 2021 2041 2045 2055
2060 2064 2067 2076 2080 2105 2107 2110 2115 2117 2190
2208 2211 2216 2220 2226 2234 2247 2255 2261 2267 2270
2290 2303 2305 2309 2315 2320 2323 2324 2330 2337 2342
2351 2357 2363 2381 2410 2462 2472 2476 2480 2488 2521
2530 2536 2543 2549 2553 2563 2590 2599 2610 2653 2682
2687 2707 2713 2726 2730 2736 2741 2756 2759 2767 2793
2799 2809 2823 2862 2868 2882 2895 2903 2912 2916 2919
2927 2933 2936 2957 2965 2971 2974 2996 2999 3005 3013
3015

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 24

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

MSN CONFIGURATION
3010 3012 3014 3016 3018 3020 3021 3023 3024 3025 3026 013
3027 3028 3029 3030 3031 3032 3033 3035 3036 3037 3039
3040 3041 3042 3043 3044 3045 3046 3047 3048 3049 3050
3052 3053 3054 3055 3056 3057 3058 3059 3060 3061 3062
3063 3064 3065 3066 3068 3069 3071 3072 3073 3074 3076
3077 3078 3079 3080 3082 3083 3084 3085 3086 3087 3088
3089 3090 3091 3093 3094 3095 3096 3097 3099 3100 3101
3102 3103 3104 3105 3107 3108 3109 3111 3113 3114 3115
3116 3117 3118 3119 3121 3122 3123 3124 3125 3127 3128
3129 3131 3132 3133 3134 3135 3136 3137 3138 3139 3140
3141 3142 3143 3144 3145 3147 3148 3149 3150 3151 3152
3153 3154 3155 3156 3157 3158 3159 3160 3161 3162 3164
3165 3166 3167 3168 3169 3170 3171 3172 3173 3174 3175
3176 3177 3178 3179 3180 3181 3182 3183 3184 3185 3186
3187 3188 3189 3190 3192 3193 3194 3195 3196 3197 3199
3200 3201 3202 3203 3204 3205 3206 3208 3209 3210 3211
3213 3214 3215 3216 3218 3219 3220 3221 3223 3224 3225
3226 3227 3228 3230 3231 3232 3234 3236 3237 3238 3239
3240 3242 3243 3245 3246 3248 3250 3252 3253 3255 3256
3257 3258 3259 3260 3261 3263 3264 3266 3268 3269 3270
3271 3272 3273 3275 3276 3277 3278 3279 3280 3281 3282
3284 3285 3286 3287 3288 3289 3291 3292 3293 3295 3296
3298 3299 3300 3301 3303 3304 3305 3306 3308 3309 3310
3311 3312 3313 3314 3316 3317 3318 3319 3320 3321 3323
3324 3325 3327 3328 3330 3331 3332 3333 3335 3336 3337
3338 3341 3342 3343 3344 3345 3346 3347 3348 3349 3351
3352 3353 3354 3356 3357 3358 3359 3361 3362 3363 3364
3365 3366 3368 3370 3371 3373 3374 3375 3376 3377 3378
3379 3380 3381 3383 3384 3385 3386 3388 3389 3390 3391
3392 3393 3394 3395 3396 3398 3400 3402 3403 3404 3406
3407 3408 3409 3410 3411 3412 3413 3414 3415 3416 3417
3418 3420 3421 3422 3423 3424 3425 3426 3427 3428 3430
3431 3432 3433 3435 3436 3437 3438 3439 3440 3442 3443
3444 3445 3446 3447 3448 3449 3450 3451 3452 3453 3454
3455 3456 3457 3460 3461 3463 3464 3465 3466 3467 3468
3469 3470 3472 3473 3474 3475 3476 3477 3478 3479 3480
3481 3482 3483 3484 3485 3486 3487 3488 3489 3490 3491
3492 3494 3495 3496 3497 3499 3500 3501 3502 3503 3505
3506 3508 3509 3510 3511 3513 3514 3515 3516 3517 3518
3519 3520 3521 3524 3526 3528 3529 3530 3531 3532 3533
3534 3535 3536 3537 3538 3540 3541 3542 3543 3544 3545
3547 3548 3549 3550 3551 3553 3554 3555 3556 3558 3559
3560 3561 3562 3563 3564 3565 3567 3568 3569 3570 3571
3572 3574 3576 3577 3578 3579 3580 3581 3582 3585 3586
3588 3589 3590 3591 3594 3595 3596 3597 3598 3599 3601
3602 3603 3604 3605 3606 3607 3608 3609 3610 3611 3613
3614 3615 3616 3617 3618 3620 3621 3622 3624 3626 3627
3628 3630 3631 3632 3634 3635 3638 3640 3641 3642 3643
3644 3646 3647 3649 3650 3651 3652 3654 3656 3657 3658
3659 3660 3661 3662 3663 3664 3666 3667 3668 3670 3671
3672 3674 3675 3676 3677 3679 3680 3683 3684 3685 3686

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 25

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

MSN CONFIGURATION
3687 3689 3690 3691 3692 3693 3694 3695 3696 3697 3698 013
3699 3700 3701 3702 3703 3704 3705 3706 3707 3709 3710
3711 3713 3714 3715 3716 3718 3719 3720 3721 3723 3724
3726 3727 3728 3729 3731 3732 3733 3734 3735 3736 3739
3741 3742 3744 3745 3746 3747 3748 3750 3751 3753 3754
3755 3756 3757 3758 3759 3763 3768 3770 3772 3774 3779
3788 3790
3022 3034 3051 3067 3070 3075 3081 3098 3106 3112 3120 010
3126 3130 3146 3191 3198 3207 3212 3217 3222 3229 3233
3235 3241 3247 3249 3251 3254 3262 3265 3267 3274 3283
3290 3294 3297 3302 3307 3315 3322 3326 3329 3334 3339
3340 3350 3355 3360 3367 3369 3372 3382 3387 3397 3399
3401 3405 3419 3429 3434 3441 3458 3459 3462 3471 3493
3498 3504 3507 3512 3522 3523 3525 3527 3539 3546 3552
3557 3566 3573 3575 3583 3584 3587 3592 3593 3600 3612
3619 3623 3625 3629 3633 3636 3637 3639 3645 3653 3655
3665 3669 3673 3678 3681 3682 3688 3708 3712 3717 3722
3725 3730 3737 3738 3740 3749 3752 3761 3764 3766 3784
3792

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 26

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

MSN CONFIGURATION
3743 3760 3762 3765 3767 3769 3771 3773 3775 3776 3777 020
3778 3780 3781 3782 3783 3785 3786 3787 3789 3791 3793
3794 3795 3797 3798 3799 3800 3801 3802 3803 3804 3805
3807 3808 3809 3810 3811 3812 3813 3815 3817 3818 3819
3822 3823 3824 3825 3826 3827 3828 3829 3831 3832 3833
3834 3835 3836 3837 3838 3839 3840 3841 3842 3843 3844
3845 3846 3848 3849 3850 3851 3852 3853 3854 3855 3856
3857 3859 3860 3861 3863 3865 3866 3868 3870 3871 3872
3873 3874 3875 3876 3877 3880 3882 3883 3885 3886 3887
3888 3889 3890 3891 3892 3894 3895 3896 3897 3898 3900
3901 3902 3903 3904 3905 3906 3907 3908 3909 3910 3911
3912 3913 3914 3915 3917 3918 3919 3921 3922 3923 3925
3927 3929 3931 3932 3933 3935 3937 3939 3941 3942 3943
3945 3946 3947 3949 3950 3952 3953 3954 3956 3957 3958
3959 3961 3962 3963 3965 3967 3968 3970 3971 3972 3974
3975 3976 3978 3979 3980 3982 3983 3984 3985 3986 3988
3990 3991 3992 3994 3995 3997 3998 3999 4000 4001 4003
4004 4006 4007 4008 4010 4011 4012 4013 4014 4015 4017
4018 4019 4020 4021 4023 4024 4026 4027 4028 4029 4030
4032 4033 4034 4035 4036 4037 4038 4039 4040 4042 4043
4046 4048 4049 4051 4052 4053 4055 4056 4057 4059 4060
4061 4063 4064 4065 4066 4068 4069 4070 4071 4072 4075
4076 4077 4079 4080 4081 4083 4084 4086 4087 4088 4089
4090 4092 4093 4094 4095 4097 4098 4100 4101 4102 4104
4105 4106 4108 4109 4110 4111 4113 4114 4115 4117 4118
4119 4120 4121 4122 4124 4125 4126 4127 4128 4129 4130
4132 4133 4135 4137 4139 4140 4141 4143 4144 4145 4146
4147 4149 4150 4151 4152 4153 4154 4156 4157 4158 4159
4160 4161 4162 4163 4164 4165 4166 4167 4168 4169 4170
4171 4172 4174 4175 4176 4177 4178 4179 4181 4182 4183
4185 4186 4187 4188 4190 4191 4192 4193 4195 4196 4197
4199 4200 4201 4202 4203 4204 4205 4206 4207 4208 4210
4211 4212 4214 4215 4216 4218 4219 4220 4222 4223 4225
4226 4227 4228 4229 4231 4232 4233 4234 4235 4236 4237
4238 4239 4240 4241 4242 4243 4244 4245 4246 4247 4248
4249 4250 4252 4253 4254 4255 4256 4257 4258 4259 4260
4261 4262 4263 4264 4265 4267 4268 4269 4270 4272 4273
4275 4276 4278 4279 4281 4282 4284 4285 4286 4287 4288
4289 4290 4291 4293 4294 4295 4296 4297 4298 4300 4301
4302 4303 4304 4305 4306 4307 4308 4309 4310 4312 4313
4314 4316 4317 4319 4320 4321 4322 4323 4324 4325 4326
4327 4328 4329 4331 4332 4333 4335 4336 4337 4339 4340
4342 4343 4344 4345 4346 4347 4348 4349 4350 4351 4353
4354 4355 4356 4357 4359 4361 4362 4363 4364 4365 4366
4367 4368 4370 4371 4372 4373 4375 4376 4378 4379 4380
4381 4383 4384 4385 4386 4388 4389 4390 4391 4392 4393
4394 4395 4396 4397 4398 4399 4400 4401 4402 4403 4404
4405 4407 4408 4409 4410 4411 4412 4413 4414 4415 4417
4418 4419 4421 4422 4423 4424 4425 4426 4427 4428 4429
4431 4432 4433 4434 4435 4436 4437 4438 4439 4440 4441
4442 4443 4444 4445 4446 4447 4448 4449 4451 4452 4453

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 27

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

MSN CONFIGURATION
4454 4455 4456 4457 4458 4459 4460 4462 4463 4464 4465 020
4466 4468 4469 4470 4471 4473 4474 4475 4476 4477 4478
4479 4480 4481 4482 4483 4484 4485 4486 4487 4488 4489
4490 4491 4492 4493 4495 4496 4497 4498 4499 4501 4502
4503 4504 4505 4506 4507 4508 4509 4510 4511 4512 4513
4514 4515 4516 4517 4518 4519 4520 4521 4522 4523 4524
4525 4526 4527 4528 4529 4531 4532 4533 4535 4536 4537
4539 4540 4541 4543 4544 4546 4547 4548 4549 4550 4551
4552 4553 4554 4555 4556 4557 4558 4559 4561 4562 4563
4564 4565 4566 4567 4568 4569 4571 4572 4573 4574 4575
4576 4578 4579 4580 4581 4582 4583 4584 4586 4587 4588
4589 4591 4592 4593 4594 4595 4596 4597 4598 4599 4600
4601 4602 4603 4604 4605 4606 4608 4609 4610 4612 4613
4614 4615 4616 4618 4619 4620 4621 4622 4623 4624 4625
4627 4628 4629 4630 4631 4632 4633 4634 4635 4636 4637
4639 4640 4641 4642 4644 4645 4646 4647 4649 4650 4651
4652 4653 4655 4656 4657 4658 4659 4660 4661 4663 4664
4665 4666 4667 4668 4670 4671 4673 4674 4675 4676 4677
4678 4679 4680 4681 4683 4684 4685 4686 4687 4688 4689
4690 4691 4692 4693 4694 4695 4696 4697 4699 4700 4701
4702 4704 4705 4707 4708 4709 4711 4712 4713 4714 4715
4716 4717 4718 4720 4721 4722 4723 4724 4725 4726 4727
4729 4730 4732 4733 4734 4735 4736 4738 4739 4740 4741
4742 4743 4744 4745 4747 4748 4749 4750 4751 4752 4754
4755 4756 4757 4758 4759 4760 4762 4763 4764 4765 4766
4767 4768 4769 4770 4772 4773 4774 4775 4776 4777 4778
4780 4781 4782 4784 4785 4786 4787 4789 4790 4791 4793
4794 4795 4796 4797 4798 4799 4800 4801 4802 4803 4804
4805 4806 4807 4808 4809 4810 4812 4813 4814 4815 4816
4817 4818 4820 4821 4822 4823 4825 4827 4828 4829 4831
4832 4833 4835 4836 4837 4839 4840 4841 4842 4844 4845
4846 4848 4849 4851 4852 4853 4854 4855 4857 4858 4859
4860 4861 4862 4864 4865 4866 4867 4868 4869 4870 4871
4872 4874 4875 4876 4877 4878 4879 4880 4882 4883 4884
4886 4887 4888 4889 4890 4891 4892 4894 4895 4896 4897
4899 4900 4902 4903 4904 4905 4906 4907 4908 4909 4910
4911 4912 4913 4914 4915 4917 4918 4919 4920 4921 4922
4924 4926 4927 4928 4929 4930 4931 4933 4934 4936 4937
4938 4939 4941 4942 4943 4944 4946 4947 4948 4950 4951
4952 4953 4954 4955 4956 4958 4959 4961 4963 4964 4965
4967 4968 4969 4970 4972 4973 4974 4975 4977 4978 4979
4980 4981 4982 4983 4984 4985 4986 4987 4988 4989 4990
4991 4992 4993 4995 4996 4997 4998 4999 5000 5001 5002
5003 5004 5005 5006 5007 5008 5010 5011 5012 5013 5014
5015 5016 5017 5018 5019 5020 5021 5022 5023 5024 5026
5027 5029 5030 5031 5032 5033 5034 5036 5037 5039 5040
5041 5042 5043 5045 5046 5047 5048 5050 5051 5052 5053
5055 5056 5057 5058 5060 5061 5062 5063 5064 5066 5067
5068 5069 5070 5071 5072 5073 5075 5076 5078 5079 5080
5081 5082 5084 5085 5086 5088 5089 5090 5091 5092 5093
5094 5095 5096 5097 5098 5100 5101 5102 5103 5104 5105

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 28

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

MSN CONFIGURATION
5106 5107 5108 5109 5110 5111 5112 5113 5114 5115 5116 020
5117 5119 5120 5121 5122 5123 5125 5127 5128 5129 5130
5131 5132 5134 5135 5136 5137 5138 5139 5140 5141 5142
5143 5144 5145 5146 5147 5148 5149 5150 5151 5152 5153
5155 5156 5157 5158 5159 5161 5162 5163 5165 5166 5167
5168 5170 5171 5172 5174 5175 5176 5178 5179 5181 5182
5183 5184 5185 5187 5188 5189 5190 5191 5193 5194 5195
5196 5198 5200 5201 5202 5203 5204 5206 5207 5208 5209
5211 5212 5213 5214 5215 5216 5217 5218 5219 5220 5221
5222 5223 5224 5225 5226 5228 5229 5230 5231 5232 5234
5236 5238 5239 5240 5242 5243 5245 5246 5248 5249 5250
5252 5253 5255 5256 5258 5259 5260 5261 5262 5263 5264
5266 5267 5268 5270 5272 5273 5274 5276 5277 5278 5280
5281 5283 5284 5286 5288 5289 5290 5291 5293 5294 5296
5298 5299 5301 5302 5304 5305 5307 5308 5310 5311 5312
5313 5315 5316 5318 5319 5320 5322 5323 5324 5325 5326
5327 5329 5330 5331 5333 5334 5335 5337 5338 5339 5341
5342 5344 5345 5347 5348 5349 5351 5352 5353 5355 5356
5358 5359 5360 5361 5362 5363 5364 5365 5366 5367 5369
5370 5371 5372 5373 5375 5376 5378 5379 5380 5381 5383
5384 5386 5387 5389 5390 5391 5393 5394 5395 5396 5397
5398 5399 5400 5401 5403 5405 5406 5407 5408 5410 5411
5412 5414 5415 5416 5417 5419 5420 5421 5423 5424 5425
5426 5428 5429 5430 5431 5433 5434 5436 5437 5439 5440
5441 5442 5443 5445 5446 5448 5449 5451 5452 5453 5454
5455 5457 5458 5460 5461 5463 5464 5466 5467 5468 5471
5472 5473 5474 5476 5477 5478 5479 5480 5482 5483 5484
5486 5487 5488 5489 5491 5492 5493 5494 5496 5497 5498
5499 5501 5502 5503 5505 5506 5507 5508 5510 5511 5512
5514 5515 5516 5517 5518 5520 5521 5522 5524 5525 5526
5527 5529 5530 5531 5532 5533 5535 5536 5537 5539 5540
5541 5542 5544 5545 5547 5548 5550 5551 5552 5553 5554
5556 5557 5559 5560 5561 5562 5563 5564 5565 5566 5568
5569 5570 5571 5572 5574 5576 5577 5578 5579 5580 5581
5583 5585 5586 5587 5589 5590 5591 5592 5593 5595 5596
5597 5598 5599 5600 5601 5602 5604 5605 5607 5608 5609
5610 5611 5612 5613 5614 5615 5616 5617 5618 5619 5620
5621 5622 5623 5624 5625 5626 5627 5628 5629 5630 5631
5632 5634 5635 5637 5638 5639 5640 5641 5642 5643 5645
5646 5648 5649 5650 5651 5652 5653 5654 5656 5657 5658
5660 5661 5662 5664 5665 5666 5668 5669 5671 5672 5673
5675 5676 5677 5678 5679 5680 5682 5683 5685 5686 5687
5688 5690 5691 5692 5693 5694 5695 5697 5698 5700 5701
5702 5703 5704 5706 5707 5708 5710 5711 5712 5713 5714
5716 5717 5718 5719 5721 5722 5723 5724 5725 5726 5727
5729 5730 5731 5732 5734 5735 5737 5738 5739 5740 5741
5742 5744 5745 5746 5748 5749 5750 5752 5753 5754 5756
5757 5759 5760 5761 5762 5764 5765 5766 5768 5769 5771
5772 5773 5775 5776 5777 5778 5780 5781 5782 5784 5785
5786 5788 5789 5791 5792 5793 5794 5796 5797 5798 5799
5801 5802 5804 5805 5806 5807 5809 5810 5811 5812 5813

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 29

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

MSN CONFIGURATION
5814 5815 5816 5817 5818 5819 5821 5822 5823 5824 5826 020
5827 5828 5829 5830 5831 5832 5833 5835 5837 5839 5840
5841 5842 5844 5845 5846 5847 5848 5850 5851 5852 5853
5855 5856 5857 5858 5859 5861 5862 5863 5864 5866 5867
5868 5869 5870 5871 5873 5874 5875 5877 5878 5879 5880
5882 5883 5885 5886 5887 5888 5889 5891 5892 5893 5894
5896 5897 5898 5900 5901 5902 5903 5905 5906 5907 5908
5910 5911 5912 5914 5915 5917 5918 5920 5921 5923 5924
5925 5926 5927 5928 5929 5930 5931 5933 5934 5935 5937
5940 5941 5942 5943 5944 5945 5948 5950 5951 5952 5953
5954 5956 5957 5959 5962 5963 5964 5965 5967 5968 5970
5971 5972 5973 5974 5976 5977 5978 5979 5981 5982 5984
5985 5986 5988 5989 5990 5992 5993 5995 5996 5997 5999
6000 6001 6003 6004 6006 6007 6008 6010 6011 6012 6014
6015 6017 6018 6019 6021 6022 6023 6025 6026 6028 6029
6030 6032 6033 6034 6036 6037 6039 6040 6041 6043 6044
6045 6047 6048 6050 6051 6052 6054 6055 6057 6058 6060
6061 6062 6064 6065 6066 6068 6069 6071 6072 6073 6075
6076 6077 6078 6079 6080 6081 6082 6084 6085 6086 6088
6090 6091 6092 6093 6095 6096 6098 6099 6102 6103 6105
6106 6107 6109 6110 6111 6112 6113 6115 6116 6117 6118
6120 6123 6124 6125 6127 6128 6129 6131 6132 6134 6135
6136 6137 6139 6140 6141 6142 6144 6145 6147 6149 6150
6151 6153 6154 6155 6157 6158 6161 6164 6166

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 30

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

MSN CONFIGURATION
3796 3806 3814 3816 3820 3830 3847 3858 3862 3864 3867 019
3869 3878 3879 3881 3884 3893 3899 3916 3920 3924 3926
3928 3930 3934 3936 3938 3940 3944 3948 3951 3955 3960
3964 3966 3969 3973 3977 3981 3987 3989 3993 3996 4002
4005 4009 4016 4022 4025 4031 4041 4044 4045 4047 4050
4054 4058 4062 4067 4073 4074 4078 4082 4085 4091 4096
4099 4103 4107 4112 4116 4123 4131 4134 4136 4138 4142
4148 4155 4173 4180 4184 4189 4194 4198 4209 4213 4217
4221 4224 4230 4251 4266 4271 4274 4277 4280 4283 4292
4299 4311 4315 4318 4334 4338 4341 4352 4358 4360 4369
4374 4377 4382 4387 4406 4416 4420 4430 4461 4467 4472
4494 4500 4530 4534 4538 4542 4545 4560 4570 4577 4585
4590 4607 4611 4617 4626 4638 4643 4648 4654 4662 4669
4672 4682 4698 4703 4706 4710 4719 4728 4731 4737 4746
4753 4761 4771 4779 4783 4788 4792 4811 4819 4824 4826
4830 4834 4838 4843 4847 4850 4856 4863 4873 4881 4885
4893 4898 4901 4916 4923 4925 4932 4935 4940 4945 4949
4957 4960 4962 4966 4971 4976 4994 5009 5025 5028 5035
5038 5044 5049 5054 5059 5065 5074 5077 5083 5087 5099
5118 5124 5126 5133 5154 5160 5164 5169 5173 5177 5180
5186 5192 5197 5199 5205 5210 5227 5233 5235 5237 5241
5244 5247 5251 5254 5257 5265 5269 5271 5275 5279 5282
5285 5287 5292 5295 5297 5300 5303 5306 5309 5314 5317
5321 5328 5332 5336 5340 5343 5346 5350 5354 5357 5368
5374 5377 5382 5385 5388 5392 5402 5404 5409 5413 5418
5422 5427 5432 5435 5438 5444 5447 5450 5456 5459 5462
5465 5469 5470 5475 5481 5485 5490 5495 5500 5504 5509
5513 5519 5523 5528 5534 5538 5543 5546 5549 5555 5558
5567 5573 5575 5582 5584 5588 5594 5603 5606 5633 5636
5644 5647 5655 5659 5663 5667 5670 5674 5681 5684 5689
5696 5699 5705 5709 5715 5720 5728 5733 5736 5743 5747
5751 5755 5758 5763 5767 5770 5774 5779 5783 5787 5790
5795 5800 5803 5808 5820 5825 5834 5836 5838 5843 5849
5854 5860 5865 5872 5876 5881 5884 5890 5895 5899 5904
5909 5913 5916 5919 5922 5932 5936 5938 5939 5946 5947
5949 5955 5958 5960 5961 5966 5969 5975 5980 5983 5987
5991 5994 5998 6002 6005 6009 6013 6016 6020 6024 6027
6031 6035 6038 6042 6046 6049 6053 6056 6059 6063 6067
6070 6074 6083 6087 6089 6094 6097 6100 6104 6108 6114
6119 6121 6122 6126 6130 6133 6138 6143 6146 6148 6152
6156 6159 6162 6163 6165

(5) Configuration definition

**CONF 001
Config. 001 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

**CONF 002
Config. 002 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 31

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 003
Config. 003 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

**CONF 004
Config. 004 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

**CONF 005
Config. 005 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

**CONF 006
Config. 006 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

**CONF 007
Config. 007 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

**CONF 008
Config. 008 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

**CONF 009
Config. 009 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

**CONF 010
Config. 010 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

**CONF 011
Config. 011 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

**CONF 012
Config. 012 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

**CONF 013
Config. 013 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

**CONF 014
Config. 014 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

**CONF 015
Config. 015 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 32

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 016
Config. 016 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

**CONF 017
Config. 017 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

**CONF 018
Config. 018 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

**CONF 019
Config. 019 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

**CONF 020
Config. 020 regards the specific MOD status of the related aircraft, refer to Configuration
Definition Table Fig. A-UABAA given in Appendix 02: Configuration Definition Table .

(6) Material Effectivity

**CONF 001

MATERIAL QTY PER A/C SEE NOTES

Kit 521165B01R01 1
Kit 521165B03R00 1
Consumable CMLB01 As required
Consumable CMLB02 As required
Standard tool TOOLB01 1
Component COMPB01 1
Reidentified part set REIDB02 1

**CONF 002

MATERIAL QTY PER A/C SEE NOTES

Kit 521165B02R01 1
Kit 521165B03R00 1
Consumable CMLB01 As required
Consumable CMLB02 As required
Standard tool TOOLB01 1
Component COMPB02 1
Reidentified part set REIDB02 1

**CONF 003

MATERIAL QTY PER A/C SEE NOTES

Kit 521165B01R01 1
Kit 521165B03R00 1

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 33

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

MATERIAL QTY PER A/C SEE NOTES

Consumable CMLB01 As required
Consumable CMLB02 As required
Standard tool TOOLB01 1
Component COMPB01 1
Reidentified part set REIDB04 1

**CONF 014

MATERIAL QTY PER A/C SEE NOTES

Kit 521165B01R01 1
Kit 521165B03R00 1
Consumable CMLB01 As required
Consumable CMLB02 As required
Standard tool TOOLB01 1
Component COMPB01 1
Reidentified part set REIDB09 1

**CONF 004

MATERIAL QTY PER A/C SEE NOTES

Kit 521165B01R01 1
Kit 521165B03R00 1
Consumable CMLB01 As required
Consumable CMLB02 As required
Standard tool TOOLB01 1
Component COMPB01 1
Reidentified part set REIDB05 1

**CONF 005

MATERIAL QTY PER A/C SEE NOTES

Kit 521165B01R01 1
Kit 521165B03R00 1
Consumable CMLB01 As required
Consumable CMLB02 As required
Standard tool TOOLB01 1
Component COMPB01 1
Reidentified part set REIDB03 1

**CONF 006

MATERIAL QTY PER A/C SEE NOTES

Kit 521165B02R01 1
Kit 521165B03R00 1
Consumable CMLB01 As required

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 34

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

MATERIAL QTY PER A/C SEE NOTES

Consumable CMLB02 As required
Standard tool TOOLB01 1
Component COMPB02 1
Reidentified part set REIDB04 1

**CONF 016

MATERIAL QTY PER A/C SEE NOTES

Kit 521165B02R01 1
Kit 521165B03R00 1
Consumable CMLB01 As required
Consumable CMLB02 As required
Standard tool TOOLB01 1
Component COMPB02 1
Reidentified part set REIDB04 1

**CONF 007

MATERIAL QTY PER A/C SEE NOTES

Kit 521165B01R01 1
Kit 521165B03R00 1
Consumable CMLB01 As required
Consumable CMLB02 As required
Standard tool TOOLB01 1
Component COMPB01 1
Reidentified part set REIDB06 1

**CONF 015

MATERIAL QTY PER A/C SEE NOTES

Kit 521165B01R01 1
Kit 521165B03R00 1
Consumable CMLB01 As required
Consumable CMLB02 As required
Standard tool TOOLB01 1
Component COMPB01 1
Reidentified part set REIDB10 1

**CONF 008

MATERIAL QTY PER A/C SEE NOTES

Kit 521165B02R01 1
Kit 521165B03R00 1
Consumable CMLB01 As required
Consumable CMLB02 As required

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 35

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

MATERIAL QTY PER A/C SEE NOTES

Standard tool TOOLB01 1
Component COMPB02 1
Reidentified part set REIDB03 1

**CONF 009, 018

MATERIAL QTY PER A/C SEE NOTES

Kit 521165B02R01 1
Kit 521165B03R00 1
Consumable CMLB01 As required
Consumable CMLB02 As required
Standard tool TOOLB01 1
Component COMPB02 1
Reidentified part set REIDB07 1

**CONF 010, 013

MATERIAL QTY PER A/C SEE NOTES

Kit 521165B02R01 1
Kit 521165B03R00 1
Consumable CMLB01 As required
Consumable CMLB02 As required
Standard tool TOOLB01 1
Component COMPB02 1
Reidentified part set REIDB08 1

**CONF 011, 017

MATERIAL QTY PER A/C SEE NOTES

Kit 521165B02R01 1
Kit 521165B03R00 1
Consumable CMLB01 As required
Consumable CMLB02 As required
Standard tool TOOLB01 1
Component COMPB02 1
Reidentified part set REIDB06 1

**CONF 012

MATERIAL QTY PER A/C SEE NOTES

Kit 521165B02R01 1
Kit 521165B03R00 1
Consumable CMLB01 As required
Consumable CMLB02 As required
Standard tool TOOLB01 1

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 36

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

MATERIAL QTY PER A/C SEE NOTES

Component COMPB02 1
Reidentified part set REIDB05 1

**CONF 019 thru 020

MATERIAL QTY PER A/C SEE NOTES

Kit 521165B02R01 1
Consumable CMLB01 As required
Standard tool TOOLB01 1
Component COMPB02 1
Reidentified part set REIDB01 1

**CONF ALL

B. CONCURRENT REQUIREMENTS

None

C. REASON

(1) History

AIRBUS have received reports of wear and corroded forward upper and lower
Post Modification No. 27716J1969 attachment/adjustment studs on the Main Landing
Gear (MLG) Door Assembly. Modification No. 27716J1969 previously introduced
attachment/adjustment studs with increased strength. These subsequent findings of
wear and corrosion have led to the issue of Inspection Service Bulletin (ISB) No.
A320-52-1163. This gives instructions for a repetitive inspection until a terminating
modification is available.

(2) Objective/Action

This Service Bulletin introduces a rod and adjuster with improved corrosion resistance
and locking feature. These will reduce the possibility of wear and corrosion.

(3) Advantages

This Service Bulletin cancels Inspection Service Bulletin A320-52-1163.

This Service Bulletin supersedes Service Bulletin A320-52-1100.

(4) Operational/Maintenance Consequences

The Operational/Maintenance Consequences of this Service Bulletin are covered by the

update of the affected publications detailed in PLANNING INFORMATION

D. DESCRIPTION

To accomplish this Service Bulletin it is necessary to :

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 37

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 001

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00

(1) Reidentify the LH MLG Fixed Fairing Assembly

(2) Reidentify the RH MLG Fixed Fairing Assembly

**CONF 002

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 38

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Revision No. 00

(1) Reidentify the LH MLG Fixed Fairing Assembly

(2) Reidentify the RH MLG Fixed Fairing Assembly

**CONF 003

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

Task 521165-831-898-001: Modification - Additional Work 3 for Aircraft Concerned by

Configurations 003 and 006 of this Revision and Modified by Revision No. 02 or any Previous
Issue, or Reidentified by the Additional Work from Revision No. 01 or Revision No. 02

(1) Reidentify the LH MLG Fixed Fairing Assembly

(2) Reidentify the RH MLG Fixed Fairing Assembly

**CONF 004

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 39

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00

(1) Reidentify the LH MLG Fixed Fairing Assembly

(2) Reidentify the RH MLG Fixed Fairing Assembly

**CONF 005

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00

(1) Reidentify the LH MLG Fixed Fairing Assembly

(2) Reidentify the RH MLG Fixed Fairing Assembly

**CONF 006

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 40

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

Task 521165-831-898-001: Modification - Additional Work 3 for Aircraft Concerned by

Configurations 003 and 006 of this Revision and Modified by Revision No. 02 or any Previous
Issue, or Reidentified by the Additional Work from Revision No. 01 or Revision No. 02

(1) Reidentify the LH MLG Fixed Fairing Assembly

(2) Reidentify the RH MLG Fixed Fairing Assembly

**CONF 007

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00

(1) Reidentify the LH MLG Fixed Fairing Assembly

(2) Reidentify the RH MLG Fixed Fairing Assembly

**CONF 008

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 41

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00

(1) Reidentify the LH MLG Fixed Fairing Assembly

(2) Reidentify the RH MLG Fixed Fairing Assembly

**CONF 009

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00

(1) Reidentify the LH MLG Fixed Fairing Assembly

(2) Reidentify the RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 42

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 010

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00

(1) Reidentify the LH MLG Fixed Fairing Assembly

(2) Reidentify the RH MLG Fixed Fairing Assembly

**CONF 011

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 43

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Revision No. 00

(1) Reidentify the LH MLG Fixed Fairing Assembly

(2) Reidentify the RH MLG Fixed Fairing Assembly

**CONF 012

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00

(1) Reidentify the LH MLG Fixed Fairing Assembly

(2) Reidentify the RH MLG Fixed Fairing Assembly

**CONF 013

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 44

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00

(1) Reidentify the LH MLG Fixed Fairing Assembly

(2) Reidentify the RH MLG Fixed Fairing Assembly

**CONF 014

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00

(1) Reidentify the LH MLG Fixed Fairing Assembly

(2) Reidentify the RH MLG Fixed Fairing Assembly

**CONF 015

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 45

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00

(1) Reidentify the LH MLG Fixed Fairing Assembly

(2) Reidentify the RH MLG Fixed Fairing Assembly

**CONF 016

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

Task 521165-831-897-001: Modification - Additional Work 2 for Aircraft Concerned by

Configuration 016 of this Revision and Modified by the Original Issue or Revision No. 01, or
Reidentified by the Additional Work from Revision No. 01

(1) Reidentify the LH MLG Fixed Fairing Assembly

(2) Reidentify the RH MLG Fixed Fairing Assembly

**CONF 017

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 46

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00

(1) Reidentify the LH MLG Fixed Fairing Assembly

(2) Reidentify the RH MLG Fixed Fairing Assembly

**CONF 018

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00

(1) Reidentify the LH MLG Fixed Fairing Assembly

(2) Reidentify the RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 47

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 019

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

**CONF 020

Task 521165-831-895-001: Modification

(1) Remove the LH MLG Fixed Fairing Assembly

(2) Remove the RH MLG Fixed Fairing Assembly

(3) Replace the LH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(4) Replace the RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment
Studs

(5) Install the LH MLG Fixed Fairing Assembly

(6) Install the RH MLG Fixed Fairing Assembly

(7) Reidentify the LH MLG Fixed Fairing Assembly

(8) Reidentify the RH MLG Fixed Fairing Assembly

**CONF ALL

E. COMPLIANCE

(1) Classification

RECOMMENDED: Service Bulletin recommended to be accomplished to prevent

significant operational disruptions.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 48

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(2) Accomplishment Timescale

Accomplishment of this Service Bulletin is recommended at the earliest opportunity

where manpower and facilities are available.

Additional Works 1, 2 and 3 of this Service Bulletin is required in order to consider

the mandatory repetitive inspections as per Service Bulletin No. A320-52-1163 as
terminated.

F. APPROVAL

The technical content of this document is approved under the authority of Design
Organisation Approval No. EASA.21J.031.

If an aircraft listed in the effectivity has a modification or repair embodied that is not of
AIRBUS origin, and which affects the content of this Service Bulletin, the operator is
responsible for obtaining approval by its airworthiness authority for any adaptation necessary
before incorporation of the Service Bulletin.

G. MANPOWER

The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also not
included.

**CONF 001

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 49

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
Get Access 0.25
On Aircraft
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
Close-Up 0.25
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 002

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
Get Access 0.25
On Aircraft
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
Close-Up 0.25
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 50

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 003

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

Task 521165-831-898-001: Modification - Additional Work 3 for Aircraft Concerned by

Configurations 003 and 006 of this Revision and Modified by Revision No. 02 or any Previous
Issue, or Reidentified by the Additional Work from Revision No. 01 or Revision No. 02
Get Access 0.25
On Aircraft
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
Close-Up 0.25
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 004

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 51

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Task 521165-831-895-001: Modification

On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
Get Access 0.25
On Aircraft
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
Close-Up 0.25
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 005

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 52

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
Get Access 0.25
On Aircraft
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
Close-Up 0.25
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 006

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

Task 521165-831-898-001: Modification - Additional Work 3 for Aircraft Concerned by

Configurations 003 and 006 of this Revision and Modified by Revision No. 02 or any Previous
Issue, or Reidentified by the Additional Work from Revision No. 01 or Revision No. 02
Get Access 0.25
On Aircraft
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
Close-Up 0.25
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 53

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 007

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
Get Access 0.25
On Aircraft
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
Close-Up 0.25
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 008

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 54

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Task 521165-831-895-001: Modification

On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
Get Access 0.25
On Aircraft
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
Close-Up 0.25
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 009

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 55

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
Get Access 0.25
On Aircraft
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
Close-Up 0.25
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 010

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
Get Access 0.25
On Aircraft
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
Close-Up 0.25
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 56

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 011

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
Get Access 0.25
On Aircraft
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
Close-Up 0.25
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 012

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 57

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Task 521165-831-895-001: Modification

On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
Get Access 0.25
On Aircraft
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
Close-Up 0.25
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 013

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 58

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
Get Access 0.25
On Aircraft
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
Close-Up 0.25
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 014

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
Get Access 0.25
On Aircraft
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
Close-Up 0.25
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 59

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 015

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
Get Access 0.25
On Aircraft
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
Close-Up 0.25
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 016

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 60

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Task 521165-831-895-001: Modification

On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

Task 521165-831-897-001: Modification - Additional Work 2 for Aircraft Concerned by

Configuration 016 of this Revision and Modified by the Original Issue or Revision No. 01, or
Reidentified by the Additional Work from Revision No. 01
Get Access 0.25
On Aircraft
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
Close-Up 0.25
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 017

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 61

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
Get Access 0.25
On Aircraft
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
Close-Up 0.25
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 018

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

Task 521165-831-896-001: Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00
Get Access 0.25
On Aircraft
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
Close-Up 0.25
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 62

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 019

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

**CONF 020

Task 521165-831-895-001: Modification

Get Access 4.00
On Aircraft
Remove the LH MLG Fixed Fairing Assembly 1.00
Remove the RH MLG Fixed Fairing Assembly 1.00
Install the LH MLG Fixed Fairing Assembly 4.00
Install the RH MLG Fixed Fairing Assembly 4.00
Reidentify the LH MLG Fixed Fairing Assembly 0.50
Reidentify the RH MLG Fixed Fairing Assembly 0.50
On Bench
Replace the LH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Replace the RH MLG Fixed Fairing Assembly Upper 1.00
and Lower Forward Attachment Studs
Tests 1.00
Close-Up 4.00
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

NOTE: For an explanation of the manhours and elapsed time, refer to the Gantt
Chart, Fig. A-UAAAA given in Appendix 01: Manpower Gantt Chart .

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 63

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF ALL

H. WEIGHT AND BALANCE

Not Changed

I. ELECTRICAL LOAD DATA

Not Changed

J. REFERENCES

**CONF 001

Aircraft Maintenance Manual (AMM) 06-20-00 12-32-24 20-11-11

20-21-11 20-28-00 32-00-00
32-12-14 32-30-00
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

**CONF 002

Aircraft Maintenance Manual (AMM) 06-20-00 12-32-24 20-11-11

20-21-11 20-28-00 32-00-00
32-12-14 32-30-00
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

**CONF 003

Aircraft Maintenance Manual (AMM) 06-20-00 11-00-00 12-32-24

20-11-11 20-21-11 20-28-00
32-00-00 32-12-14 32-30-00
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 64

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Process and Material Specification (PMS) Process and Material Specification

(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

**CONF 004

Aircraft Maintenance Manual (AMM) 06-20-00 12-32-24 20-11-11

20-21-11 20-28-00 32-00-00
32-12-14 32-30-00
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

**CONF 005

Aircraft Maintenance Manual (AMM) 06-20-00 12-32-24 20-11-11

20-21-11 20-28-00 32-00-00
32-12-14 32-30-00
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

**CONF 006

Aircraft Maintenance Manual (AMM) 06-20-00 11-00-00 12-32-24

20-11-11 20-21-11 20-28-00
32-00-00 32-12-14 32-30-00
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 65

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 007

Aircraft Maintenance Manual (AMM) 06-20-00 12-32-24 20-11-11

20-21-11 20-28-00 32-00-00
32-12-14 32-30-00
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

**CONF 008

Aircraft Maintenance Manual (AMM) 06-20-00 12-32-24 20-11-11

20-21-11 20-28-00 32-00-00
32-12-14 32-30-00
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

**CONF 009

Aircraft Maintenance Manual (AMM) 06-20-00 12-32-24 20-11-11

20-21-11 20-28-00 32-00-00
32-12-14 32-30-00
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

**CONF 010

Aircraft Maintenance Manual (AMM) 06-20-00 12-32-24 20-11-11

20-21-11 20-28-00 32-00-00
32-12-14 32-30-00
Consumable Material List (CML)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 66

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ATA Common Support Data Dictionary (CSDD),

Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

**CONF 011

Aircraft Maintenance Manual (AMM) 06-20-00 12-32-24 20-11-11

20-21-11 20-28-00 32-00-00
32-12-14 32-30-00
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

**CONF 012

Aircraft Maintenance Manual (AMM) 06-20-00 12-32-24 20-11-11

20-21-11 20-28-00 32-00-00
32-12-14 32-30-00
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

**CONF 013

Aircraft Maintenance Manual (AMM) 06-20-00 12-32-24 20-11-11

20-21-11 20-28-00 32-00-00
32-12-14 32-30-00
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 67

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00

51-75-12

**CONF 014

Aircraft Maintenance Manual (AMM) 06-20-00 12-32-24 20-11-11

20-21-11 20-28-00 32-00-00
32-12-14 32-30-00
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

**CONF 015

Aircraft Maintenance Manual (AMM) 06-20-00 12-32-24 20-11-11

20-21-11 20-28-00 32-00-00
32-12-14 32-30-00
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

**CONF 016

Aircraft Maintenance Manual (AMM) 06-20-00 11-00-00 12-32-24

20-11-11 20-21-11 20-28-00
32-00-00 32-12-14 32-30-00
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 68

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 017

Aircraft Maintenance Manual (AMM) 06-20-00 12-32-24 20-11-11

20-21-11 20-28-00 32-00-00
32-12-14 32-30-00
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

**CONF 018

Aircraft Maintenance Manual (AMM) 06-20-00 12-32-24 20-11-11

20-21-11 20-28-00 32-00-00
32-12-14 32-30-00
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

**CONF 019

Aircraft Maintenance Manual (AMM) 06-20-00 12-32-24 20-11-11

20-21-11 20-28-00 32-00-00
32-12-14 32-30-00
Consumable Material List (CML)
ATA Common Support Data Dictionary (CSDD),
Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

**CONF 020

Aircraft Maintenance Manual (AMM) 06-20-00 12-32-24 20-11-11

20-21-11 20-28-00 32-00-00
32-12-14 32-30-00
Consumable Material List (CML)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 69

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ATA Common Support Data Dictionary (CSDD),

Chapter 2
Elec. Std. Practices Manual (ESPM) 20-51-20 20-55-00
Process and Material Specification (PMS) Process and Material Specification
(PMS) 01-06-13
Standards Manual (SM)
Structural Repair Manual (SRM) 51-24-00 51-42-00 51-43-00
51-75-12

**CONF ALL

K. PUBLICATION AFFECTED

Aircraft Maintenance Manual (AMM) 32-12-14

Illustrated Parts Catalog (IPC) 52-81-13
Maintenance Planning Document (MPD) 32-12-14
528113-02-1

L. INTERCHANGEABILITY/MIXABILITY

**CONF 001

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5284024420000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 002

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 70

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5285600720000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 003

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5284024420000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 004

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 71

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5284024420000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 005

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5284024420000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 006

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 72

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5285600720000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 007

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5284024420000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 008

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 73

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5285600720000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 009

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5285600720000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 010

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 74

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5285600720000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 011

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5285600720000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 012

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 75

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5285600720000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 013

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5285600720000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 014

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 76

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5284024420000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 015

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5284024420000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 016

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 77

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5285600720000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 017

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5285600720000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 018

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 78

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5285600720000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 019

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5285600720000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF 020

The interchangeability/mixability possibilities are for new or modified parts introduced by the
accomplishment of this Service Bulletin.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 79

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

DESCRIPTION OLD PART N˚ NEW PART N˚ INT MIXABILITY SEE

NOTES
Stud-Adjustment D5285600720000 D5285610020000 03 Not (1)
Applicable

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE (1): ICY Code 03 not interchangeable but One Way Interchangeable with
conditions. These conditions are:

- When old part number is removed, it may be replaced with the same old
part number

- With new part number only if the complete set of old part numbers is
replaced by a complete set of new part numbers. Set comprises of 4
attachment studs (2LH and 2RH)

- When a new part number is removed, it must be replaced only by a New

Part Number.

**CONF ALL

M. SPARES

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 80

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2. MATERIAL INFORMATION

**CONF ALL

A. MATERIAL - PRICE AND AVAILABILITY

(1) Procurement Addresses

Customers with aircraft shown in the effectivity of this Service Bulletin should send a
purchase order to AIRBUS. Quote the number of this Service Bulletin. The address is:

Kit 521165B01R01 AIRBUS Material, Logistics and Suppliers

Kit 521165B02R01 ATP II B,
Kit 521165B03R00 Hein-Sass-Weg 24
21129 HAMBURG
GERMANY
For ordering by internet:
http://spares.airbus.com
For ordering by E-mail: [email protected]
Telephone Hotline:
A318/319/320/321: +49 40 743 51660

(2) Price and Availability

Kit 521165B01R01
Cost 3,020.00 USD
Availability 120 calendar days from receipt of order

The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning schedule
with your order so that we can try to comply with your requirements.

The sales terms (costs and availability) are estimated in relation to economic conditions.
The latest valid price and lead time for ordering purposes shall be obtained through the
Airbus Spares portal or through a request for quotation to [email protected].

Kit 521165B02R01
Cost 2,620.00 USD
Availability 120 calendar days from receipt of order

The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning schedule
with your order so that we can try to comply with your requirements.

The sales terms (costs and availability) are estimated in relation to economic conditions.
The latest valid price and lead time for ordering purposes shall be obtained through the
Airbus Spares portal or through a request for quotation to [email protected].

Kit 521165B03R00
Cost 130.00 USD
Availability 120 calendar days from receipt of order

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 81

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning schedule
with your order so that we can try to comply with your requirements.

The sales terms (costs and availability) are estimated in relation to economic conditions.
The latest valid price and lead time for ordering purposes shall be obtained through the
Airbus Spares portal or through a request for quotation to [email protected].

B. INDUSTRY SUPPORT INFORMATION

AIRBUS will not provide industry support for accomplishment of this Service Bulletin.

This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign.

For the organization of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department.

AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
France
E-mail: [email protected]

C. LIST OF COMPONENTS

Kit 521165B01R01

ITEM NEW PART N˚ QTY (UM) KEYWORD ITEM OLD PART N˚ INT SEE
NOTES
1 NAS1193K8CP 4 LOCKDVC
3 NAS509-8 4 NUT
5 D5285610020000 4 STUD ADJ (5) D5284024420000 03
6 D5285600400200 2 ROD END (6) D5284000500000
7 D5285600500200 2 ROD END (7) D5284000600000
8 D5285600620000 4 PLATE (8) D5284024820000
(8) D5284024820200
9 NAS509-9 4 NUT (3) NAS509-8
36 NSA9117-20 2 PLATE (36) NSA9117-20

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE: If you find part numbers of hardware components in the related kit(s) which
you cannot identify in the LIST OF COMPONENTS of this Service Bulletin,
refer to Standards Manual (SM). The SM will give you the correct part number
to part number relationship.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 82

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Kit 521165B02R01

ITEM NEW PART N˚ QTY (UM) KEYWORD ITEM OLD PART N˚ INT SEE
NOTES
1 NAS1193K8CP 4 LOCKDVC
3 NAS509-8 4 NUT
5 D5285610020000 4 STUD ADJ (5) D5285600720000 03
6 D5285600400200 2 ROD END (6) D5285600400000
7 D5285600500200 2 ROD END (7) D5285600500000
9 NAS509-9 4 NUT (9) NAS1423-9
36 NSA9117-20 2 PLATE (36) NSA9117-20

NOTE: For definitions of interchangeability codes in column INT., refer to ATA

Common Support Data Dictionary (CSDD), Chapter 2.

NOTE: If you find part numbers of hardware components in the related kit(s) which
you cannot identify in the LIST OF COMPONENTS of this Service Bulletin,
refer to Standards Manual (SM). The SM will give you the correct part number
to part number relationship.

Kit 521165B03R00

ITEM NEW PART N˚ QTY (UM) KEYWORD ITEM OLD PART N˚ INT SEE
NOTES
36 NSA9117-20 2 PLATE (36) NSA9117-20

NOTE: If you find part numbers of hardware components in the related kit(s) which
you cannot identify in the LIST OF COMPONENTS of this Service Bulletin,
refer to Standards Manual (SM). The SM will give you the correct part number
to part number relationship.

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts shall
be ordered as necessary through the given channel.

D. LIST OF MATERIALS - OPERATOR SUPPLIED

(1) Consumable Materials

To accomplish this Service Bulletin it is necessary to use the consumable materials

listed in the subsequent referenced AMM tasks: AMM 20-28-00, Page Block 201.

Consumable CMLB01

ITEM DESCRIPTION REFERENCE TO CML QTY PER A/C SEE

MAT. No. NOTES
Synthetic Oil Base Grease-General 03GBC1 As required
Purpose Lithium
Top Coat Polyurethane-Decorative 04JMD3 As required
External Struc

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 83

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM DESCRIPTION REFERENCE TO CML QTY PER A/C SEE

MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Polysulfide Sealant-Low Adhesion 06AEA1 As required
Brushable
Polysulfide Sealant-Low Adhesion 06AEB2 As required
Fillet Structure
Non Aqueous Cleaner-General 08BAA9 As required
Wire-Locking Dia: 0.8 Mm Cres 14QFB1 As required
Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Consumable CMLB02

ITEM DESCRIPTION REFERENCE TO CML QTY PER A/C SEE

MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner-General 08BAA9 As required
Textile-Lint Free Cotton 14SBA1 As required

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

(2) Components

Component COMPB01

ITEM NEW PART N˚ QTY (UM) KEYWORD ITEM OLD PART N˚ INT SEE
NOTES
26 MS24665-155 8 PIN
27 MS24665-300 2 PIN

NOTE: If you find part numbers of hardware components in the related kit(s)
which you cannot identify in the LIST OF COMPONENTS of this Service
Bulletin, refer to Standards Manual (SM). The SM will give you the
correct part number to part number relationship.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Component COMPB02

ITEM NEW PART N˚ QTY (UM) KEYWORD ITEM OLD PART N˚ INT SEE
NOTES
26 MS24665-155 8 PIN
27 MS24665-300 2 PIN

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 84

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

NOTE: If you find part numbers of hardware components in the related kit(s)
which you cannot identify in the LIST OF COMPONENTS of this Service
Bulletin, refer to Standards Manual (SM). The SM will give you the
correct part number to part number relationship.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

(3) Equipment

None

E. PARTS TO BE RE-IDENTIFIED BY OPERATOR

Reidentified part set REIDB01

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE

NOTES
15 D5285601001000 FAIRING (15) D5285601000600
15 D5285601001100 FAIRING (15) D5285601000700

Reidentified part set REIDB02

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE

NOTES
15 D5284000000495 FAIRING (15) D5284000000200
(15) D5284000000400
15 D5284000000595 FAIRING (15) D5284000000300
(15) D5284000000500

Reidentified part set REIDB03

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE

NOTES
15 D5285300300095 FAIRING (15) D5285300300000
15 D5285300300195 FAIRING (15) D5285300300100

Reidentified part set REIDB04

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE

NOTES
15 D5285600000095 FAIRING (15) D5285600000000
15 D5285600000195 FAIRING (15) D5285600000100
15 D5285875100095 FAIRING (15) D5285875100000
15 D5285875100195 FAIRING (15) D5285875100100

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 85

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Reidentified part set REIDB05

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE

NOTES
15 D5284000000695 FAIRING (15) D5284000000600
15 D5284000000795 FAIRING (15) D5284000000700

Reidentified part set REIDB06

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE

NOTES
15 D5285600000295 FAIRING (15) D5285600000200
(15) D5285601000000
15 D5285600000395 FAIRING (15) D5285600000300
(15) D5285601000100

Reidentified part set REIDB07

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE

NOTES
15 D5285601000295 FAIRING (15) D5285601000200
15 D5285601000395 FAIRING (15) D5285601000300

Reidentified part set REIDB08

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE

NOTES
15 D5285601000495 FAIRING (15) D5285601000400
15 D5285601000595 FAIRING (15) D5285601000500

Reidentified part set REIDB09

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE

NOTES
15 D5285600000095 FAIRING (15) D5285600000000
15 D5285600000195 FAIRING (15) D5285600000100

Reidentified part set REIDB10

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE

NOTES
15 D5285600000295 FAIRING (15) D5285600000200
15 D5285600000395 FAIRING (15) D5285600000300

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 86

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

F. TOOLING

(1) Tooling - Price and Availability

(a) Procurement Addresses

Customers with aircraft shown in the effectivity of this Service Bulletin should send
a purchase order to AIRBUS. Quote the number of this Service Bulletin. The
address is:

Standard tool TOOLB01 AIRBUS Material, Logistics and Suppliers

IFD - In Flight Desk
Weg beim Jaeger 150
D-22335 HAMBURG
GERMANY
For ordering by internet:
http://[email protected]
For ordering by fax: +49 40 50 76 4012
For ordering by E-mail:
[email protected]

(b) Price and Availability

Standard tool TOOLB01

Procurement to be negotiated directly with AIRBUS Material, Logistics and

Suppliers.

(2) Tools

To accomplish this Service Bulletin it is necessary to use the standard tools listed in the
subsequent referenced AMM tasks:

- AMM Task 32-12-14-000-001

- AMM Task 32-12-14-400-002

- AMM Task 20-28-00-912-004

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE

NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

(3) Special Tools

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 87

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

This Page Intentionally Left Blank

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 88

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

3. ACCOMPLISHMENT INSTRUCTIONS

Task 521165-831-895-001 - Modification

WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION
BEFORE YOU START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE
FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED
DOORS - COMPONENTS THAT MOVE.

CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP

ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE). WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:

- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS

NECESSARY ON WIRING AND COMPONENTS.

- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND

OTHER CONTAMINATION.

THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION

AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.

IF THERE IS CONTAMINATION, REFER TO ESPM 20-55-00.

NOTE: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
’refer to’ are used and the operator has a procedure accepted by the local authority
he belongs to, the accepted alternative procedure can be used. When the words ’in
accordance with’ are used then the given procedure must be followed.

NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.

NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.

NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance
necessary to ensure the continued airworthiness of the aircraft.

For any deviations to the instructions contained herein, contact Airbus for further
instructions and approval.

NOTE: Discarded parts must be managed at the operator’s discretion.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 89

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Task Associated Data

**CONF 001

Zone
732 742
Manpower
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

**CONF 002

Zone
732 742
Manpower
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

**CONF 003

Zone
732 742
Manpower
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

**CONF 004

Zone
732 742
Manpower
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

**CONF 005

Zone
732 742
Manpower
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

**CONF 006

Zone
732 742
Manpower
TOTAL MANHOURS 22.00

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 90

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ELAPSED TIME (HOURS) 6.00

**CONF 007

Zone
732 742
Manpower
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

**CONF 008

Zone
732 742
Manpower
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

**CONF 009

Zone
732 742
Manpower
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

**CONF 010

Zone
732 742
Manpower
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

**CONF 011

Zone
732 742
Manpower
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

**CONF 012

Zone
732 742
Manpower
TOTAL MANHOURS 22.00

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 91

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ELAPSED TIME (HOURS) 6.00

**CONF 013

Zone
732 742
Manpower
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

**CONF 014

Zone
732 742
Manpower
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

**CONF 015

Zone
732 742
Manpower
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

**CONF 016

Zone
732 742
Manpower
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

**CONF 017

Zone
732 742
Manpower
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

**CONF 018

Zone
732 742
Manpower
TOTAL MANHOURS 22.00

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 92

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ELAPSED TIME (HOURS) 6.00

**CONF 019

Zone
732 742
Manpower
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

**CONF 020

Zone
732 742
Manpower
TOTAL MANHOURS 22.00
ELAPSED TIME (HOURS) 6.00

**CONF ALL

A. GENERAL

**CONF 001

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 93

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 002

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 94

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 95

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 003

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 96

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 004

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 97

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 005

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 98

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 006

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 99

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 100

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 007

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 101

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 008

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 102

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 009

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 103

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 104

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 010

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 105

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 011

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 106

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 012

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 107

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 013

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 108

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 109

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 014

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 110

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 015

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 111

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 016

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 112

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 113

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 017

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 114

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 018

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 115

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 019

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 116

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 020

(1) Subtask 521165-910-401-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 117

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
Task 20-11-11-991-001
Task 20-11-11-991-008
Task 20-21-11-911-001
Task 20-28-00-912-004
Consumable Material List (CML)
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-24-00
51-42-00
51-43-00
51-75-12

(a) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.

(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(c) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(d) Tag all the parts you must remove and retain to make the subsequent installation
easier.

(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.

(f) Apply sealant in accordance with SRM 51-24-00.

(g) To safety fasteners with locking wire, refer to AMM Task 20-11-11-991-001.

(h) To safety fasteners with cotter pins, refer to AMM Task 20-11-11-991-008.

(i) If the length of any fastener specified in this Service Bulletin does not meet
installation standards given in SRM Chapter 51, then a fastener of the same
specification, or an approved substitute, with a length which meets the installation
standards given in SRM Chapter 51 may be used. In addition, washers may be
installed for fastener grip length in accordance with SRM Chapter 51.

(j) If alternative and substitute fasteners have to be used, you must make sure that the
associated nut/collar are compatible in accordance with SRM 51-40-00 ’Mating Part’
column.

(k) Remove and install fasteners in accordance with SRM 51-42-00.

(l) Renew the protective finish in accordance with SRM 51-75-12.

(m) Obtain alternative and substitute fastener data in accordance with SRM 51-43-00.

(n) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 118

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(2) Subtask 521165-839-401-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF ALL

B. PREPARATION

**CONF 001

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 119

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

**CONF 002

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 120

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 003

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

**CONF 004

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 121

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

**CONF 005

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 122

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

**CONF 006

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 123

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

**CONF 007

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 124

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

**CONF 008

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 125

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

**CONF 009

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 126

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

**CONF 010

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 127

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

**CONF 011

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 128

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 012

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

**CONF 013

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 129

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

**CONF 014

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 130

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

**CONF 015

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 131

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

**CONF 016

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 132

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

**CONF 017

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 133

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

**CONF 018

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 134

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

**CONF 019

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 135

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

**CONF 020

(1) Subtask 521165-941-401-001 - Job Set-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 12-32-24-869-002
Task 32-12-14-000-001
Task 32-30-00-867-001
Task 32-30-00-867-002

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-32-24-869-002.

(b) Do the Job Set-Up procedure as specified in the removal of the MLG Fixed Fairing
assembly, refer to AMM Task 32-12-14-000-001.

(c) Do the Job Set-up procedure as specified in the retraction of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Set-up procedure as specified in the extension of the landing gear for
maintenance, refer to AMM Task 32-30-00-867-002.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 136

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF ALL

C. PROCEDURE

**CONF 001

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(3) Subtask 521165-960-401-001 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 137

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
8 D5285600620000 2 PLATE
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAA Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAA Sheet 01.

4 Nut NAS509-8 Item (3) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 138

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5284000500000 Item (6) Discard

1 Rod Assy-End Upper D5284000600000 Item (7) Discard

2 Stud-Adjustment D5284024420000 Item (5) Discard

2 Plate-Support D5284024820200 Item (8) Discard

or

2 Plate-Support D5284024820000 Item (8) Discard

(b) Install on the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

2 Plate-Support D5285600620000 Item 8

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 139

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item 3 and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-001 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
8 D5285600620000 2 PLATE
9 NAS509-9 2 NUT

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 140

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAA Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAA Sheet 01.

4 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5284000500000 Item (6) Discard

1 Rod Assy-End Upper D5284000600000 Item (7) Discard

2 Stud-Adjustment D5284024420000 Item (5) Discard

2 Plate-Support D5284024820200 Item (8) Discard

or

2 Plate-Support D5284024820000 Item (8) Discard

(b) Install on the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 141

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Plate-Support D5285600620000 Item 8

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 142

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

They will be torque tightened during the installation of the MLG

fixed fairing assembly procedure.

(5) Subtask 521165-420-401-001 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 143

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-UBBAA
Sheet 03 View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 144

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAA Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBBAA Sheet 02, Fig. A-UBBAA Sheet 03 and Fig. A-UBBAA Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAA Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAA Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 145

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

6 Install, refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficient enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 146

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAA Sheet 01, Fig. A-UBBAA Sheet 03, View C and Fig. A-UBCAA Sheet
01

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00mm (+ 0.00 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.00 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7), until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAA Sheet 01
and Fig. A-UBBAA Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 147

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

15 If it is necessary, adjust each stud Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAA Sheet 01, View
A and Fig. A-UBBAA Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAA Sheet 01 and Fig.
A-UBBAA Sheet 03, View C.

20 Install, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAA Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 148

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet
02, View B and Fig. A-UBDAA Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B
and Fig. A-UBBAA Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6), and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

30 Make sure that the rod-ends, Item (6), and (7), are parallel to the MLG bracket
lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 149

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAA Sheet 01,
View A and Fig. A-UBBAA Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24), and screws, Item (25), refer to
Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-
UBDAA Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAA
Sheet 01 and Fig. A-UBBAA Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAA Sheet 01 andFig. A-UBBAA Sheet 03, View C and
View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAA Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 150

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAA Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAA Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAA Sheet 01, View
A, Fig. A-UBBAA Sheet 02, View B, Fig. A-UBBAA Sheet 03, View C and Fig.
A-UBDAA Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of adjuster (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 151

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(6) Subtask 521165-420-402-001 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 152

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-UBBAA
Sheet 03, View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 153

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAA Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBBAA Sheet 02, Fig. A-UBBAA Sheet 03 and Fig. A-UBBAA Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAA Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAA Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 154

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

6 Install, refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficient enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAA Sheet 01, Fig. A-UBBAA Sheet 03, View C and Fig. A-UBCAA Sheet
01

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 155

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- at position H, dimension T between + 0.000 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.00 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7), until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAA Sheet 01
and Fig. A-UBBAA Sheet 03, View C.

15 If it is necessary, adjust each stud Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAA Sheet 01, View
A and Fig. A-UBBAA Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 156

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAA Sheet 01 and Fig.
A-UBBAA Sheet 03, View C.

20 Install, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAA Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 157

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

25 Torque the nuts, Item (3), to between 4.0 m.daN (354.02 lbf in.) and 4.30
m.daN (380.58 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-
UBBAA Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet
02, View B and Fig. A-UBDAA Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B
and Fig. A-UBBAA Sheet 03, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6), and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

30 Make sure that the rod-ends, Item (6), and (7), are parallel to the MLG bracket
lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 158

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAA Sheet 01,
View A and Fig. A-UBBAA Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24), and screws, Item (25), refer to
Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-
UBDAA Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAA
Sheet 01 and Fig. A-UBBAA Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAA Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 159

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAA Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAA Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAA Sheet 01, View
A, Fig. A-UBBAA Sheet 02, View B, Fig. A-UBBAA Sheet 03, View C and Fig.
A-UBDAA Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of adjuster (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 160

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(7) Subtask 521165-930-401-001 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB02

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5284000000495 FAIRING (15) D5284000000200
(15) D5284000000400

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 161

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBCAA Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5284000000200 Item (15)

or

1 Fairing Assembly D5284000000400 Item (15)

becomes:

1 Fairing Assembly D5284000000495 Item 15

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 162

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(8) Subtask 521165-930-402-001 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB02

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5284000000595 FAIRING (15) D5284000000300
(15) D5284000000500

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 163

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBCAA Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5284000000300 Item (15)

or

1 Fairing Assembly D5284000000500 Item (15)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 164

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

becomes:

1 Fairing Assembly D5284000000595 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 002

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 165

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(3) Subtask 521165-960-401-002 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 166

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAB Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAB Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 167

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item 3 and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-002 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 168

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAB Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAB Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 169

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 170

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(5) Subtask 521165-420-401-002 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 171

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 172

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-UBBAB
Sheet 03, View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAB Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAB Sheet 01.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAB Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 173

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

3 Install, refer to Fig. A-UBBAB Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

6 Install, refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet
02, View B:

2 Nut Item (3) Retain

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 174

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAB Sheet 01, Fig. A-UBBAB Sheet 03, View C and Fig. A-UBCAB Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal
.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 175

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAB Sheet 01
and Fig. A-UBBAB Sheet 03, View C.

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAB Sheet 01, View
A and Fig. A-UBBAB Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAB Sheet 01 and Fig.
A-UBBAB Sheet 03, View C.

20 Install, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAB Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 176

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet
02, View B and Fig. A-UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B
and Fig. A-UBBAB Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN(300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 177

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

30 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAB Sheet 01,
View A and Fig. A-UBBAB Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer to Fig.
A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-
UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAB
Sheet 01 and Fig. A-UBBAB Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAB Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 178

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAB Sheet 02, View B.

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAB Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAB Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAB Sheet 01, View
A, Fig. A-UBBAB Sheet 02, View B, Fig. A-UBBAB Sheet 03, View C and Fig.
A-UBDAB Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 179

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(6) Subtask 521165-420-402-002 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 180

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-UBBAB
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 181

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAB Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBBAB Sheet 02, Fig. A-UBBAB Sheet 03 and Fig. A-UBBAB Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAB Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAB Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 182

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

6 Install, refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 183

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAB Sheet 01, Fig. A-UBBAB Sheet 03, View C and Fig. A-UBCAB Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAB Sheet 01
and Fig. A-UBBAB Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 184

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAB Sheet 01, View
A and Fig. A-UBBAB Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAB Sheet 01 and Fig.
A-UBBAB Sheet 03, View C.

20 Install, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAB Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 185

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet
02, View B and Fig. A-UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B
and Fig. A-UBBAB Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

30 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 186

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAB Sheet 01,
View A and Fig. A-UBBAB Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer to Fig.
A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-
UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAB
Sheet 01 and Fig. A-UBBAB Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAB Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAB Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 187

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAB Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAB Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAB Sheet 01, View
A, Fig. A-UBBAB Sheet 02, View B, Fig. A-UBBAB Sheet 03, View C and Fig.
A-UBDAB Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 188

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(7) Subtask 521165-930-401-002 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB02

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5284000000495 FAIRING (15) D5284000000200
(15) D5284000000400

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 189

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBCAB Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5284000000200 Item (15)

or

1 Fairing Assembly D5284000000400 Item (15)

becomes:

1 Fairing Assembly D5284000000495 Item 15

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 190

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(8) Subtask 521165-930-402-002 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB02

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5284000000595 FAIRING (15) D5284000000300
(15) D5284000000500

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 191

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBCAB Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5284000000300 Item (15)

or

1 Fairing Assembly D5284000000500 Item (15)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 192

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

becomes:

1 Fairing Assembly D5284000000595 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 003

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 193

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(3) Subtask 521165-960-401-004 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 1
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
8 D5285600620000 2 PLATE
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAC Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAC Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAC Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 194

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBDAC Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAC Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAC Sheet 01.

4 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5284000500000 Item (6) Discard

1 Rod Assy-End Upper D5284000600000 Item (7) Discard

2 Stud-Adjustment D5284024420000 Item (5) Discard

2 Plate-Support D5284024820200 Item (8) Discard

or

2 Plate-Support D5284024820000 Item (8) Discard

(b) Install on the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

2 Plate-Support D5285600620000 Item 8

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 195

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-003 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 196

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
8 D5285600620000 2 PLATE
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAC Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAC Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAC Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAC Sheet 01.

4 Nut NAS509-8 Item (3) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 197

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5284000500000 Item (6) Discard

1 Rod Assy-End Upper D5284000600000 Item (7) Discard

2 Stud-Adjustment D5284024420000 Item (5) Discard

2 Plate-Support D5284024820200 Item (8) Discard

or

2 Plate-Support D5284024820000 Item (8) Discard

(b) Install on the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

2 Plate-Support D5285600620000 Item 8

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 198

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(5) Subtask 521165-420-401-003 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 199

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Top Coat Polyurethane- 04JMD3 As required
Decorative External Struc
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Polysulfide Sealant-Low 06AEA1 As required
Adhesion Brushable
Polysulfide Sealant-Low 06AEB2 As required
Adhesion Fillet Structure
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAC Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAC Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAC Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly
Fig. A-UBAAC Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 200

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAC Sheet 01, View A, Fig. A-UBBAC Sheet 02, View B and Fig. A-UBBAC
Sheet 03, View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAC Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAC Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAC
Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 201

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBAAC Sheet
01,Fig. A-UBBAC Sheet 02, Fig. A-UBBAC Sheet 03 and Fig. A-UBBAC Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAC Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAC Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBAAC Sheet 01, View A and
Fig. A-UBBAC Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAC Sheet 01, View A and Fig.
A-UBBAC Sheet 04, View G.

6 Install, refer to Fig. A-UBBAC Sheet 01 and Fig. A-UBBAC Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 202

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficient enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAC Sheet 01, Fig. A-UBBAC Sheet 03, View C and Fig. A-UBCAC Sheet
01

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 203

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7), until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAC
Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer toFig. A-UBBAC Sheet 01
and Fig. A-UBBAC Sheet 03, View C.

15 If it is necessary, adjust each stud Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAC Sheet 01, View
A and Fig. A-UBBAC Sheet 02, View B.

16 Refer to Fig. A-UBCAC Sheet 01 and Fig. A-UBCAC Sheet 02, adjust the 1A
fairing, item 32, as follows:

a Measure the dimension A and make sure that the dimension is a

maximum of 3 mm (0.118 in.).

b If necessary, adjust the position of the 1A extension, item 32, as follows:

- loosen the bolts, items 33 and 35 and nuts, item 34

- adjust the 1A fairing item, 32, to get dimension A.

c Torque the bolts, items 33 and 35 and nuts, item 34 to between 0.7
m.daN (61.95 lbf in.) and 0.8 m.daN (70.80 lbf in.).

d Apply sealant to bolts, items 33 and 35 and nuts, item 34, Fig. A-UBCAC
Sheet 02.

use:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 204

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Polysulfide Sealant- 06AEA1 As required

Low Adhesion
Brushable
or

Polysulfide Sealant- 06AEB2 As required

Low Adhesion Fillet
Structure

e Mark three black lines on the MLG fixed fairing, refer to Fig. A-UBBAC
Sheet 01, item 15

and Fig. A-UBCAC Sheet 02

use:

Top Coat 04JMD3 As required

Polyurethane-
Decorative External
Struc

17 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAC
Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

NOTE: Do not final torque at this stage.

18 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

19 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

20 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAC Sheet 01 and Fig.
A-UBBAC Sheet 03, View C.

21 Install, refer to Fig. A-UBBAC Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

22 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAC Sheet 03, View F.

23

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 205

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

24 Remove from the bolt, Item (17), refer to Fig. A-UBBAC Sheet 01, View A and
Fig. A-UBBAC Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

25 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAC Sheet 01, View A and Fig.
A-UBBAC Sheet 04, View G.

26 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380 58 lbf.in.), refer to Fig. A-UBBAC Sheet 01, View A and Fig. A-UBBAC
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

27

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

28 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAC Sheet 01, View A, Fig. A-UBBAC Sheet
02, View B and Fig. A-UBDAC Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

29 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAC Sheet 01, View A,Fig. A-UBBAC Sheet 02, View B
and Fig. A-UBBAC Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 206

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

rod end and stud assembly.

30 Hold the rod-ends, Item (6), and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

31 Make sure that the rod-ends, Item (6), and (7), are parallel to the MLG bracket
lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

32

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

33 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAC Sheet 01,
View A and Fig. A-UBBAC Sheet 02, View B.

34 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

35 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

36 Apply sealant to the cover plates, Item (24), and screws, Item (25), refer to
Fig. A-UBBAC Sheet 01, View A, Fig. A-UBBAC Sheet 02, View B and Fig. A-
UBDAC Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

37 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAC
Sheet 01 and Fig. A-UBBAC Sheet 03, View C.

38 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAC Sheet 01, Fig. A-UBBAC Sheet 03, View C and
View E.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 207

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

39

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

40 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177 01 lbf in.), refer to Fig. A-UBBAC Sheet 02, View B.

41 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAC Sheet 01, View A.

42 Safety the nut, Item (19), refer to Fig. A-UBBAC Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

43 Safety the nut, Item (40), refer to Fig. A-UBBAC Sheet 01, View B

With:

1 Pin-Cotter MS24665-300 Item 27

44 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAC Sheet 01 and Fig. A-UBBAC
Sheet 03, View C.

45 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

46

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAC Sheet 01, View
A, Fig. A-UBBAC Sheet 02, View B, Fig. A-UBBAC Sheet 03, View C and Fig.
A-UBDAC Sheet 01.

- bolts (13) and washers (14)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 208

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of adjuster (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(6) Subtask 521165-420-402-003 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Top Coat Polyurethane- 04JMD3 As required
Decorative External Struc
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Polysulfide Sealant-Low 06AEA1 As required
Adhesion Brushable
Polysulfide Sealant-Low 06AEB2 As required
Adhesion Fillet Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 209

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE

CML MAT. No. NOTES
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAC Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAC Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAC Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 210

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAC Sheet 01, View A, Fig. A-UBBAC Sheet 02, View B and Fig. A-UBBAC
Sheet 03, View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAC Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAC Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAC
Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAC Sheet
01,Fig. A-UBBAC Sheet 02, Fig. A-UBBAC Sheet 03 and Fig. A-UBBAC Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAC Sheet 02, View B:

1 Bush Item (16) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 211

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAC Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAC Sheet 01, View A and
Fig. A-UBBAC Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAC Sheet 01, View A and Fig.
A-UBBAC Sheet 04, View G.

6 Install, refer to Fig. A-UBBAC Sheet 01 and Fig. A-UBBAC Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficient enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 212

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAC Sheet 01, Fig. A-UBBAC Sheet 03, View C and Fig. A-UBCAC Sheet
01

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7), until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 213

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAC
Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAC Sheet 01
and Fig. A-UBBAC Sheet 03, View C.

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAC Sheet 01, View
A and Fig. A-UBBAC Sheet 02, View B.

16 Refer toFig. A-UBCAC Sheet 01 and Fig. A-UBCAC Sheet 02, adjust the 1A
fairing, item 32, as follows:

a Measure the dimension A and make sure that the dimension is a

maximum of 3 mm (0.118 in.).

b If necessary, adjust the position of the 1A extension, item 32, as follows:

- loosen the bolts, items 33 and 35 and nuts, item 34

- adjust the 1A fairing item, 32, to get dimension A.

c Torque the bolts, items 33 and 35 and nuts, item 34 to between 0.7
m.daN (61.95 lbf in.) and 0.8 m.daN (70.80 lbf in.).

d Apply sealant to bolts, items 33 and 35 and nuts, item 34, Fig. A-UBCAC
Sheet 02.

use:

Polysulfide Sealant- 06AEA1 As required

Low Adhesion
Brushable
or

Polysulfide Sealant- 06AEB2 As required

Low Adhesion Fillet
Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 214

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

e Mark three black lines on the MLG fixed fairing, refer to Fig. A-UBBAC
Sheet 01, item 15

and Fig. A-UBCAC Sheet 02

use:

Top Coat 04JMD3 As required

Polyurethane-
Decorative External
Struc

17 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAC
Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

NOTE: Do not final torque at this stage.

18 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

19 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

20 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAC Sheet 01 and Fig.
A-UBBAC Sheet 03, View C.

21 Install, refer to Fig. A-UBBAC Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

22 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAC Sheet 03, View F.

23

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 215

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

24 Remove from the bolt, Item (17), refer to Fig. A-UBBAC Sheet 01, View A and
Fig. A-UBBAC Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

25 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAC Sheet 01, View A and Fig.
A-UBBAC Sheet 04, View G.

26 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380 58 lbf.in.), refer to Fig. A-UBBAC Sheet 01, View A and Fig. A-UBBAC
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

27

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

28 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAC Sheet 01, View A, Fig. A-UBBAC Sheet
02, View B and Fig. A-UBDAC Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

29 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAC Sheet 01, View A, Fig. A-UBBAC Sheet 02, View B
and Fig. A-UBBAC Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

30 Hold the rod-ends, Item (6), and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 216

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

31 Make sure that the rod-ends, Item (6), and (7), are parallel to the MLG bracket
lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

32

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

33 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAC Sheet 01,
View A and Fig. A-UBBAC Sheet 02, View B.

34 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

35 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

36 Apply sealant to the cover plates, Item (24), and screws, Item (25), refer to
Fig. A-UBBAC Sheet 01, View A, Fig. A-UBBAC Sheet 02, View B and Fig. A-
UBDAC Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

37 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAC
Sheet 01 and Fig. A-UBBAC Sheet 03, View C.

38 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAC Sheet 01 and Fig. A-UBBAC Sheet 03, View E.

39

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 217

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

40 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177 01 lbf in.), refer to Fig. A-UBBAC Sheet 02, View B.

41 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAC Sheet 01, View A.

42 Safety the nut, Item (19), refer to Fig. A-UBBAC Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

43 Safety the nut, Item (40), refer to Fig. A-UBBAC Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

44 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAC Sheet 01 and Fig. A-UBBAC
Sheet 03, View C.

45 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

46

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAC Sheet 01, View
A, Fig. A-UBBAC Sheet 02, View B, Fig. A-UBBAC Sheet 03, View C and Fig.
A-UBDAC Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 218

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- nuts 9, eye-ends (6) and (7) and end of adjuster (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(7) Subtask 521165-930-401-003 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB04

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000095 FAIRING (15) D5285600000000
15 D5285875100095 FAIRING (15) D5285875100000

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAC Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 219

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBBAC Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAC Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAC Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAC Sheet 03.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAC Sheet 01,
Fig. A-UBCAC Sheet 03 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285600000000 Item (15)

becomes:

1 Fairing Assembly D5285600000095 Item 15

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 220

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

or

1 Fairing Assembly D5285875100000 Item (15)

becomes:

1 Fairing Assembly D5285875100095 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(8) Subtask 521165-930-402-003 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB04

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000195 FAIRING (15) D5285600000100
15 D5285875100195 FAIRING (15) D5285875100100

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 221

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAC Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAC Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAC Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAC Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAC Sheet 03.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAC Sheet 01,
Fig. A-UBCAC Sheet 03 and PMS 01-06-13.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 222

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing assembly D5285600000100 Item (15)

becomes:

1 Fairing Assembly D5285600000195 Item 15

or

1 Fairing Assembly D5285875100100 Item (15)

becomes:

1 Fairing Assembly D5285875100195 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 004

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 223

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(3) Subtask 521165-960-401-001 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
8 D5285600620000 2 PLATE
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 224

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAA Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAA Sheet 01.

4 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5284000500000 Item (6) Discard

1 Rod Assy-End Upper D5284000600000 Item (7) Discard

2 Stud-Adjustment D5284024420000 Item (5) Discard

2 Plate-Support D5284024820200 Item (8) Discard

or

2 Plate-Support D5284024820000 Item (8) Discard

(b) Install on the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

2 Plate-Support D5285600620000 Item 8

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 225

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item 3 and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-001 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 226

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
8 D5285600620000 2 PLATE
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAA Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAA Sheet 01.

4 Nut NAS509-8 Item (3) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 227

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5284000500000 Item (6) Discard

1 Rod Assy-End Upper D5284000600000 Item (7) Discard

2 Stud-Adjustment D5284024420000 Item (5) Discard

2 Plate-Support D5284024820200 Item (8) Discard

or

2 Plate-Support D5284024820000 Item (8) Discard

(b) Install on the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

2 Plate-Support D5285600620000 Item 8

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 228

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(5) Subtask 521165-420-401-001 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 229

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 230

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-UBBAA
Sheet 03 View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAA Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBBAA Sheet 02, Fig. A-UBBAA Sheet 03 and Fig. A-UBBAA Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 231

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Install, refer to Fig. A-UBBAA Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAA Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

6 Install, refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficient enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 232

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAA Sheet 01, Fig. A-UBBAA Sheet 03, View C and Fig. A-UBCAA Sheet
01

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00mm (+ 0.00 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.00 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 233

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7), until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAA Sheet 01
and Fig. A-UBBAA Sheet 03, View C.

15 If it is necessary, adjust each stud Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAA Sheet 01, View
A and Fig. A-UBBAA Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAA Sheet 01 and Fig.
A-UBBAA Sheet 03, View C.

20 Install, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAA Sheet 03, View F.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 234

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet
02, View B and Fig. A-UBDAA Sheet 01.

Use:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 235

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B
and Fig. A-UBBAA Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6), and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

30 Make sure that the rod-ends, Item (6), and (7), are parallel to the MLG bracket
lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAA Sheet 01,
View A and Fig. A-UBBAA Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24), and screws, Item (25), refer to
Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-
UBDAA Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 236

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAA
Sheet 01 and Fig. A-UBBAA Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAA Sheet 01 andFig. A-UBBAA Sheet 03, View C and
View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAA Sheet 02, View B.

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAA Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAA Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 237

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAA Sheet 01, View
A, Fig. A-UBBAA Sheet 02, View B, Fig. A-UBBAA Sheet 03, View C and Fig.
A-UBDAA Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of adjuster (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(6) Subtask 521165-420-402-001 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 238

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 239

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-UBBAA
Sheet 03, View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAA Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBBAA Sheet 02, Fig. A-UBBAA Sheet 03 and Fig. A-UBBAA Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 240

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Install, refer to Fig. A-UBBAA Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAA Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

6 Install, refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficient enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 241

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAA Sheet 01, Fig. A-UBBAA Sheet 03, View C and Fig. A-UBCAA Sheet
01

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.000 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.00 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 242

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7), until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAA Sheet 01
and Fig. A-UBBAA Sheet 03, View C.

15 If it is necessary, adjust each stud Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAA Sheet 01, View
A and Fig. A-UBBAA Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAA Sheet 01 and Fig.
A-UBBAA Sheet 03, View C.

20 Install, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAA Sheet 03, View F.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 243

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

25 Torque the nuts, Item (3), to between 4.0 m.daN (354.02 lbf in.) and 4.30
m.daN (380.58 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-
UBBAA Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet
02, View B and Fig. A-UBDAA Sheet 01.

Use:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 244

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B
and Fig. A-UBBAA Sheet 03, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6), and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

30 Make sure that the rod-ends, Item (6), and (7), are parallel to the MLG bracket
lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAA Sheet 01,
View A and Fig. A-UBBAA Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24), and screws, Item (25), refer to
Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-
UBDAA Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 245

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAA
Sheet 01 and Fig. A-UBBAA Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAA Sheet 02, View B.

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAA Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAA Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 246

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Apply sealant to the items that follow, refer to Fig. A-UBBAA Sheet 01, View
A, Fig. A-UBBAA Sheet 02, View B, Fig. A-UBBAA Sheet 03, View C and Fig.
A-UBDAA Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of adjuster (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(7) Subtask 521165-930-401-006 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB05

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5284000000695 FAIRING (15) D5284000000600

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 247

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE

CML MAT. No. NOTES
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 248

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBCAA Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5284000000600 Item (15)

becomes:

1 Fairing Assembly D5284000000695 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(8) Subtask 521165-930-402-006 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB05

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5284000000795 FAIRING (15) D5284000000700

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 249

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE

CML MAT. No. NOTES
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 250

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBCAA Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5284000000700 Item (15)

becomes:

1 Fairing Assembly D5284000000795 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 005

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 251

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(3) Subtask 521165-960-401-001 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
8 D5285600620000 2 PLATE
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 252

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAA Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAA Sheet 01.

4 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5284000500000 Item (6) Discard

1 Rod Assy-End Upper D5284000600000 Item (7) Discard

2 Stud-Adjustment D5284024420000 Item (5) Discard

2 Plate-Support D5284024820200 Item (8) Discard

or

2 Plate-Support D5284024820000 Item (8) Discard

(b) Install on the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

2 Plate-Support D5285600620000 Item 8

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 253

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item 3 and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-001 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 254

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
8 D5285600620000 2 PLATE
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAA Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAA Sheet 01.

4 Nut NAS509-8 Item (3) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 255

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5284000500000 Item (6) Discard

1 Rod Assy-End Upper D5284000600000 Item (7) Discard

2 Stud-Adjustment D5284024420000 Item (5) Discard

2 Plate-Support D5284024820200 Item (8) Discard

or

2 Plate-Support D5284024820000 Item (8) Discard

(b) Install on the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

2 Plate-Support D5285600620000 Item 8

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 256

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(5) Subtask 521165-420-401-001 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 257

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 258

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-UBBAA
Sheet 03 View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAA Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBBAA Sheet 02, Fig. A-UBBAA Sheet 03 and Fig. A-UBBAA Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 259

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Install, refer to Fig. A-UBBAA Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAA Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

6 Install, refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficient enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 260

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAA Sheet 01, Fig. A-UBBAA Sheet 03, View C and Fig. A-UBCAA Sheet
01

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00mm (+ 0.00 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.00 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 261

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7), until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAA Sheet 01
and Fig. A-UBBAA Sheet 03, View C.

15 If it is necessary, adjust each stud Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAA Sheet 01, View
A and Fig. A-UBBAA Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAA Sheet 01 and Fig.
A-UBBAA Sheet 03, View C.

20 Install, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAA Sheet 03, View F.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 262

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet
02, View B and Fig. A-UBDAA Sheet 01.

Use:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 263

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B
and Fig. A-UBBAA Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6), and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

30 Make sure that the rod-ends, Item (6), and (7), are parallel to the MLG bracket
lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAA Sheet 01,
View A and Fig. A-UBBAA Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24), and screws, Item (25), refer to
Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-
UBDAA Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 264

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAA
Sheet 01 and Fig. A-UBBAA Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAA Sheet 01 andFig. A-UBBAA Sheet 03, View C and
View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAA Sheet 02, View B.

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAA Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAA Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 265

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAA Sheet 01, View
A, Fig. A-UBBAA Sheet 02, View B, Fig. A-UBBAA Sheet 03, View C and Fig.
A-UBDAA Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of adjuster (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(6) Subtask 521165-420-402-001 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 266

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 267

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-UBBAA
Sheet 03, View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAA Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBBAA Sheet 02, Fig. A-UBBAA Sheet 03 and Fig. A-UBBAA Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 268

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Install, refer to Fig. A-UBBAA Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAA Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

6 Install, refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficient enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 269

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAA Sheet 01, Fig. A-UBBAA Sheet 03, View C and Fig. A-UBCAA Sheet
01

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.000 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.00 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 270

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7), until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAA Sheet 01
and Fig. A-UBBAA Sheet 03, View C.

15 If it is necessary, adjust each stud Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAA Sheet 01, View
A and Fig. A-UBBAA Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAA Sheet 01 and Fig.
A-UBBAA Sheet 03, View C.

20 Install, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAA Sheet 03, View F.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 271

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

25 Torque the nuts, Item (3), to between 4.0 m.daN (354.02 lbf in.) and 4.30
m.daN (380.58 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-
UBBAA Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet
02, View B and Fig. A-UBDAA Sheet 01.

Use:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 272

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B
and Fig. A-UBBAA Sheet 03, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6), and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

30 Make sure that the rod-ends, Item (6), and (7), are parallel to the MLG bracket
lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAA Sheet 01,
View A and Fig. A-UBBAA Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24), and screws, Item (25), refer to
Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-
UBDAA Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 273

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAA
Sheet 01 and Fig. A-UBBAA Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAA Sheet 02, View B.

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAA Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAA Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 274

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Apply sealant to the items that follow, refer to Fig. A-UBBAA Sheet 01, View
A, Fig. A-UBBAA Sheet 02, View B, Fig. A-UBBAA Sheet 03, View C and Fig.
A-UBDAA Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of adjuster (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(7) Subtask 521165-930-401-016 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB03

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285300300095 FAIRING (15) D5285300300000

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 275

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE

CML MAT. No. NOTES
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 276

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBCAA Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285300300000 Item (15)

becomes:

1 Fairing Assembly D5285300300095 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(8) Subtask 521165-930-402-016 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB03

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285300300195 FAIRING (15) D5285300300100

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 277

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE

CML MAT. No. NOTES
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 278

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBCAA Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285300300100 Item (15)

becomes:

1 Fairing Assembly D5285300300195 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 006

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 279

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(3) Subtask 521165-960-401-005 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001
Task 32-12-14-400-002
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 280

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAD Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAD Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 281

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 282

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(4) Subtask 521165-960-402-004 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAD Sheet 01.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 283

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAD Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 284

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(5) Subtask 521165-420-401-004 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 285

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Top Coat Polyurethane- 04JMD3 As required
Decorative External Struc
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Polysulfide Sealant-Low 06AEA1 As required
Adhesion Brushable
Polysulfide Sealant-Low 06AEB2 As required
Adhesion Fillet Structure
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 286

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-UBBAD
Sheet 03, View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAD Sheet 03, View D.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 287

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

4 Remove, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAD Sheet
01, Fig. A-UBBAD Sheet 02, Fig. A-UBBAD Sheet 03 and Fig. A-UBBAD Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAD Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAD Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 288

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

6 Install, refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAD Sheet 01, Fig. A-UBBAD Sheet 03, View C and Fig. A-UBCAD Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between - 0.00 mm (- 0.000 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 289

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates, Item (8), refer to
Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal
.

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer toFig. A-UBBAD Sheet 01
and Fig. A-UBBAD Sheet 03, View C.

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAD Sheet 01, View
A and Fig. A-UBBAD Sheet 02, View B.

16 Refer to Fig. A-UBCAD Sheet 01 and Fig. A-UBCAD Sheet 02, adjust the 1A
fairing, item 32, as follows:

a Measure the dimension A and make sure that the dimension is a

maximum of 3.00 mm (0.118 in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 290

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

b If necessary, adjust the position of the 1A extension, item 32, as follows:

- Loosen the bolts, items 33 and 35 and nuts, item 34.

- Adjust the 1A fairing item, 32, to get dimension A.

c Torque the bolts, items 33 and 35 and nuts, item 34 to between 0.7
m.daN (61.95 lbf in.) and 0.8 m.daN (70.80 lbf in.).

d Apply sealant to bolts, items 33 and 35 and nuts, item 34, Fig. A-UBCAD
Sheet 02.

use:

Polysulfide Sealant- 06AEA1 As required

Low Adhesion
Brushable
or

Polysulfide Sealant- 06AEB2 As required

Low Adhesion Fillet
Structure

e Mark three black lines on the MLG fixed fairing, refer toFig. A-UBBAD
Sheet 01, item 15

and Fig. A-UBCAD Sheet 02

use:

Top Coat 04JMD3 As required

Polyurethane-
Decorative External
Struc

17 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

NOTE: Do not final torque at this stage.

18 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

19 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

20 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAD Sheet 01 and Fig.
A-UBBAD Sheet 03, View C.

21 Install, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 291

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

3 Bolt Item (13) Retained at

removal

22 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAD Sheet 03, View F.

23

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

24 Remove from the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

25 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

26 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

27

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 292

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

28 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet
02, View B and Fig. A-UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

29 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B
and Fig. A-UBBAD Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

30 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.328 lbf in.).

31 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

32

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

33 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAD Sheet 01,
View A and Fig. A-UBBAD Sheet 02, View B.

34 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

35 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 293

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

36 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer toFig.
A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-
UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

37 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAD
Sheet 01 and Fig. A-UBBAD Sheet 03, View C.

38 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAD Sheet 03, View E.

39

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

40 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAD Sheet 02, View B.

41 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01, View A.

42 Safety the nut, Item (19), refer to Fig. A-UBBAD Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

43 Safety the nut, Item (40), refer to Fig. A-UBBAD Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

44 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 294

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

45 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

46

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAD Sheet 01, View
A, Fig. A-UBBAD Sheet 02, View B, Fig. A-UBBAD Sheet 03, View C and Fig.
A-UBDAD Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(6) Subtask 521165-420-402-004 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 295

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM NEW PART N˚ QTY (UM) KEYWORD SEE

NOTES
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Top Coat Polyurethane- 04JMD3 As required
Decorative External Struc
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Polysulfide Sealant-Low 06AEA1 As required
Adhesion Brushable
Polysulfide Sealant-Low 06AEB2 As required
Adhesion Fillet Structure
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 296

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-UBBAD
Sheet 03, View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAD Sheet 03, View D.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 297

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

4 Remove, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAD Sheet
01, Fig. A-UBBAD Sheet 02, Fig. A-UBBAD Sheet 03 and Fig. A-UBBAD Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAD Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAD Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 298

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

6 Install, refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAD Sheet 01, Fig. A-UBBAD Sheet 03, View C and Fig. A-UBCAD Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between - 0.00 mm (+ 0.000 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 299

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates, Item (8), refer to
Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer toFig. A-UBBAD Sheet 01
and Fig. A-UBBAD Sheet 03, View C.

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAD Sheet 01, View
A and Fig. A-UBBAD Sheet 02, View B.

16 Refer to Fig. A-UBCAD Sheet 01 and Fig. A-UBCAD Sheet 02, adjust the 1A
fairing, item 32, as follows:

a Measure the dimension A and make sure that the dimension is a

maximum of 3 mm (0.118 in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 300

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

b If necessary, adjust the position of the 1A extension, item 32, as follows:

- loosen the bolts, items 33 and 35 and nuts, item 34

- adjust the 1A fairing item, 32, to get dimension A.

c Torque the bolts, items 33 and 35 and nuts, item 34 to between 0.7
m.daN (61.95 lbf in.) and 0.8 m.daN (70.80 lbf in.).

d Apply sealant to bolts, items 33 and 35 and nuts, item 34, Fig. A-UBCAD
Sheet 02.

use:

Polysulfide Sealant- 06AEA1 As required

Low Adhesion
Brushable
or

Polysulfide Sealant- 06AEB2 As required

Low Adhesion Fillet
Structure

e Mark three black lines on the MLG fixed fairing, refer toFig. A-UBBAD
Sheet 01, item 15 and Fig. A-UBCAD Sheet 02

use:

Top Coat 04JMD3 As required

Polyurethane-
Decorative External
Struc

17 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

NOTE: Do not final torque at this stage.

18 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

19 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

20 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAD Sheet 01 and Fig.
A-UBBAD Sheet 03, View C.

21 Install, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 301

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

3 Bolt Item (13) Retained at

removal

22 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAD Sheet 03, View F.

23

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

24 Remove from the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

25 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

26 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

27

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 302

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

28 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet
02, View B and Fig. A-UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

29 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B
and Fig. A-UBBAD Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

30 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.328 lbf in.).

31 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

32

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

33 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAD Sheet 01,
View A and Fig. A-UBBAD Sheet 02, View B.

34 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAD Sheet 01.

35 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 303

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

36 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer toFig.
A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-
UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

37 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAD
Sheet 01 and Fig. A-UBBAD Sheet 03, View C.

38 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAD Sheet 03, View E.

39

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

40 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAD Sheet 02, View B.

41 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01, View A.

42 Safety the nut, Item (19), refer to Fig. A-UBBAD Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

43 Safety the nut, Item (40), refer to Fig. A-UBBAD Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

44 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 304

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

45 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

46

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAD Sheet 01, View
A, Fig. A-UBBAD Sheet 02, View B, Fig. A-UBBAD Sheet 03, View C and Fig.
A-UBDAD Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(7) Subtask 521165-930-401-004 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 305

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Reidentified part set REIDB04

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000095 FAIRING (15) D5285600000000
15 D5285875100095 FAIRING (15) D5285875100000

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows,

refer to Fig. A-UBCAD Sheet 03.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 306

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAD Sheet 01,
Fig. A-UBCAD Sheet 03 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285600000000 Item (15)

becomes:

1 Fairing Assembly D5285600000095 Item 15

or

1 Fairing Assembly D5285875100000 Item (15)

becomes:

1 Fairing Assembly D5285875100095 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(8) Subtask 521165-930-402-004 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 307

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB04

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000195 FAIRING (15) D5285600000100
15 D5285875100195 FAIRING (15) D5285875100100

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAD Sheet 03.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 308

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAD Sheet 01,
Fig. A-UBCAD Sheet 03 and PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing assembly D5285600000100 Item (15)

becomes:

1 Fairing Assembly D5285600000195 Item 15

or

1 Fairing Assembly D5285875100100 Item (15)

becomes:

1 Fairing Assembly D5285875100195 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 007

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 309

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(3) Subtask 521165-960-401-004 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 1
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 310

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM NEW PART N˚ QTY (UM) KEYWORD SEE

NOTES
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
8 D5285600620000 2 PLATE
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAC Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAC Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAC Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAC Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAC Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAC Sheet 01.

4 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 311

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Rod Assy-End Lower D5284000500000 Item (6) Discard

1 Rod Assy-End Upper D5284000600000 Item (7) Discard

2 Stud-Adjustment D5284024420000 Item (5) Discard

2 Plate-Support D5284024820200 Item (8) Discard

or

2 Plate-Support D5284024820000 Item (8) Discard

(b) Install on the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

2 Plate-Support D5285600620000 Item 8

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 312

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-003 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
8 D5285600620000 2 PLATE
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 313

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBAAC Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAC Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAC Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAC Sheet 01.

4 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5284000500000 Item (6) Discard

1 Rod Assy-End Upper D5284000600000 Item (7) Discard

2 Stud-Adjustment D5284024420000 Item (5) Discard

2 Plate-Support D5284024820200 Item (8) Discard

or

2 Plate-Support D5284024820000 Item (8) Discard

(b) Install on the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

2 Plate-Support D5285600620000 Item 8

2 Stud Adjustment D5285610020000 Item 5

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 314

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 315

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(5) Subtask 521165-420-401-003 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Top Coat Polyurethane- 04JMD3 As required
Decorative External Struc
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Polysulfide Sealant-Low 06AEA1 As required
Adhesion Brushable
Polysulfide Sealant-Low 06AEB2 As required
Adhesion Fillet Structure
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 316

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAC Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAC Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAC Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly
Fig. A-UBAAC Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 317

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAC Sheet 01, View A, Fig. A-UBBAC Sheet 02, View B and Fig. A-UBBAC
Sheet 03, View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAC Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAC Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAC
Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBAAC Sheet
01,Fig. A-UBBAC Sheet 02, Fig. A-UBBAC Sheet 03 and Fig. A-UBBAC Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAC Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 318

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

3 Install, refer to Fig. A-UBBAC Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBAAC Sheet 01, View A and
Fig. A-UBBAC Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAC Sheet 01, View A and Fig.
A-UBBAC Sheet 04, View G.

6 Install, refer to Fig. A-UBBAC Sheet 01 and Fig. A-UBBAC Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficient enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet
02, View B:

2 Nut Item (3) Retain

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 319

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAC Sheet 01, Fig. A-UBBAC Sheet 03, View C and Fig. A-UBCAC Sheet
01

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7), until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 320

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAC
Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer toFig. A-UBBAC Sheet 01
and Fig. A-UBBAC Sheet 03, View C.

15 If it is necessary, adjust each stud Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAC Sheet 01, View
A and Fig. A-UBBAC Sheet 02, View B.

16 Refer to Fig. A-UBCAC Sheet 01 and Fig. A-UBCAC Sheet 02, adjust the 1A
fairing, item 32, as follows:

a Measure the dimension A and make sure that the dimension is a

maximum of 3 mm (0.118 in.).

b If necessary, adjust the position of the 1A extension, item 32, as follows:

- loosen the bolts, items 33 and 35 and nuts, item 34

- adjust the 1A fairing item, 32, to get dimension A.

c Torque the bolts, items 33 and 35 and nuts, item 34 to between 0.7
m.daN (61.95 lbf in.) and 0.8 m.daN (70.80 lbf in.).

d Apply sealant to bolts, items 33 and 35 and nuts, item 34, Fig. A-UBCAC
Sheet 02.

use:

Polysulfide Sealant- 06AEA1 As required

Low Adhesion
Brushable
or

Polysulfide Sealant- 06AEB2 As required

Low Adhesion Fillet
Structure

e Mark three black lines on the MLG fixed fairing, refer to Fig. A-UBBAC
Sheet 01, item 15

and Fig. A-UBCAC Sheet 02

use:

Top Coat 04JMD3 As required

Polyurethane-
Decorative External
Struc

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 321

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

17 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAC
Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

NOTE: Do not final torque at this stage.

18 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

19 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

20 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAC Sheet 01 and Fig.
A-UBBAC Sheet 03, View C.

21 Install, refer to Fig. A-UBBAC Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

22 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAC Sheet 03, View F.

23

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

24 Remove from the bolt, Item (17), refer to Fig. A-UBBAC Sheet 01, View A and
Fig. A-UBBAC Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

25 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAC Sheet 01, View A and Fig.
A-UBBAC Sheet 04, View G.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 322

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

26 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380 58 lbf.in.), refer to Fig. A-UBBAC Sheet 01, View A and Fig. A-UBBAC
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

27

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

28 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAC Sheet 01, View A, Fig. A-UBBAC Sheet
02, View B and Fig. A-UBDAC Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

29 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAC Sheet 01, View A,Fig. A-UBBAC Sheet 02, View B
and Fig. A-UBBAC Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

30 Hold the rod-ends, Item (6), and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

31 Make sure that the rod-ends, Item (6), and (7), are parallel to the MLG bracket
lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

32

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 323

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

33 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAC Sheet 01,
View A and Fig. A-UBBAC Sheet 02, View B.

34 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

35 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

36 Apply sealant to the cover plates, Item (24), and screws, Item (25), refer to
Fig. A-UBBAC Sheet 01, View A, Fig. A-UBBAC Sheet 02, View B and Fig. A-
UBDAC Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

37 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAC
Sheet 01 and Fig. A-UBBAC Sheet 03, View C.

38 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAC Sheet 01, Fig. A-UBBAC Sheet 03, View C and
View E.

39

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

40 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177 01 lbf in.), refer to Fig. A-UBBAC Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 324

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

41 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAC Sheet 01, View A.

42 Safety the nut, Item (19), refer to Fig. A-UBBAC Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

43 Safety the nut, Item (40), refer to Fig. A-UBBAC Sheet 01, View B

With:

1 Pin-Cotter MS24665-300 Item 27

44 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAC Sheet 01 and Fig. A-UBBAC
Sheet 03, View C.

45 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

46

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAC Sheet 01, View
A, Fig. A-UBBAC Sheet 02, View B, Fig. A-UBBAC Sheet 03, View C and Fig.
A-UBDAC Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of adjuster (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 325

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(6) Subtask 521165-420-402-003 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Top Coat Polyurethane- 04JMD3 As required
Decorative External Struc
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Polysulfide Sealant-Low 06AEA1 As required
Adhesion Brushable
Polysulfide Sealant-Low 06AEB2 As required
Adhesion Fillet Structure
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 326

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAC Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAC Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAC Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAC Sheet 01, View A, Fig. A-UBBAC Sheet 02, View B and Fig. A-UBBAC
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 327

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAC Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAC Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAC
Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAC Sheet
01,Fig. A-UBBAC Sheet 02, Fig. A-UBBAC Sheet 03 and Fig. A-UBBAC Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAC Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAC Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 328

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAC Sheet 01, View A and
Fig. A-UBBAC Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAC Sheet 01, View A and Fig.
A-UBBAC Sheet 04, View G.

6 Install, refer to Fig. A-UBBAC Sheet 01 and Fig. A-UBBAC Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficient enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 329

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAC Sheet 01, Fig. A-UBBAC Sheet 03, View C and Fig. A-UBCAC Sheet
01

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7), until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAC
Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAC Sheet 01
and Fig. A-UBBAC Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 330

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAC Sheet 01, View
A and Fig. A-UBBAC Sheet 02, View B.

16 Refer toFig. A-UBCAC Sheet 01 and Fig. A-UBCAC Sheet 02, adjust the 1A
fairing, item 32, as follows:

a Measure the dimension A and make sure that the dimension is a

maximum of 3 mm (0.118 in.).

b If necessary, adjust the position of the 1A extension, item 32, as follows:

- loosen the bolts, items 33 and 35 and nuts, item 34

- adjust the 1A fairing item, 32, to get dimension A.

c Torque the bolts, items 33 and 35 and nuts, item 34 to between 0.7
m.daN (61.95 lbf in.) and 0.8 m.daN (70.80 lbf in.).

d Apply sealant to bolts, items 33 and 35 and nuts, item 34, Fig. A-UBCAC
Sheet 02.

use:

Polysulfide Sealant- 06AEA1 As required

Low Adhesion
Brushable
or

Polysulfide Sealant- 06AEB2 As required

Low Adhesion Fillet
Structure

e Mark three black lines on the MLG fixed fairing, refer to Fig. A-UBBAC
Sheet 01, item 15

and Fig. A-UBCAC Sheet 02

use:

Top Coat 04JMD3 As required

Polyurethane-
Decorative External
Struc

17 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAC
Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

NOTE: Do not final torque at this stage.

18 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 331

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

19 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

20 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAC Sheet 01 and Fig.
A-UBBAC Sheet 03, View C.

21 Install, refer to Fig. A-UBBAC Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

22 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAC Sheet 03, View F.

23

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

24 Remove from the bolt, Item (17), refer to Fig. A-UBBAC Sheet 01, View A and
Fig. A-UBBAC Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

25 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAC Sheet 01, View A and Fig.
A-UBBAC Sheet 04, View G.

26 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380 58 lbf.in.), refer to Fig. A-UBBAC Sheet 01, View A and Fig. A-UBBAC
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

27

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 332

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

28 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAC Sheet 01, View A, Fig. A-UBBAC Sheet
02, View B and Fig. A-UBDAC Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

29 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAC Sheet 01, View A, Fig. A-UBBAC Sheet 02, View B
and Fig. A-UBBAC Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

30 Hold the rod-ends, Item (6), and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

31 Make sure that the rod-ends, Item (6), and (7), are parallel to the MLG bracket
lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

32

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 333

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

33 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAC Sheet 01,
View A and Fig. A-UBBAC Sheet 02, View B.

34 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAC Sheet 01, View A and Fig. A-UBBAC Sheet 02, View B.

35 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

36 Apply sealant to the cover plates, Item (24), and screws, Item (25), refer to
Fig. A-UBBAC Sheet 01, View A, Fig. A-UBBAC Sheet 02, View B and Fig. A-
UBDAC Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

37 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAC
Sheet 01 and Fig. A-UBBAC Sheet 03, View C.

38 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAC Sheet 01 and Fig. A-UBBAC Sheet 03, View E.

39

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

40 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177 01 lbf in.), refer to Fig. A-UBBAC Sheet 02, View B.

41 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAC Sheet 01, View A.

42 Safety the nut, Item (19), refer to Fig. A-UBBAC Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 334

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

43 Safety the nut, Item (40), refer to Fig. A-UBBAC Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

44 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAC Sheet 01 and Fig. A-UBBAC
Sheet 03, View C.

45 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

46

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAC Sheet 01, View
A, Fig. A-UBBAC Sheet 02, View B, Fig. A-UBBAC Sheet 03, View C and Fig.
A-UBDAC Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of adjuster (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(7) Subtask 521165-930-401-008 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 335

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB06

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000295 FAIRING (15) D5285600000200
(15) D5285601000000

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAC Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAC Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAC Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAC Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 336

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAC Sheet 03.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAC Sheet 01,
Fig. A-UBCAC Sheet 03 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285600000200 Item (15)

or

1 Fairing Assembly D5285601000000 Item (15)

becomes:

1 Fairing Assembly D5285600000295 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(8) Subtask 521165-930-402-008 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 337

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB06

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000395 FAIRING (15) D5285600000300
(15) D5285601000100

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAC Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAC Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAC Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAC Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 338

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAC Sheet 03.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAC Sheet 01,
Fig. A-UBCAC Sheet 03 and PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285600000300 Item (15)

or

1 Fairing Assembly D5285601000100 Item (15)

becomes:

1 Fairing Assembly D5285600000395 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 339

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 008

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(3) Subtask 521165-960-401-002 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 340

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAB Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAB Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 341

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 342

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item 3 and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-002 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 343

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAB Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAB Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 344

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 345

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

They will be torque tightened during the installation of the MLG

fixed fairing assembly procedure.

(5) Subtask 521165-420-401-002 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 346

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-UBBAB
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 347

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAB Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAB Sheet 01.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAB Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAB Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 348

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

6 Install, refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 349

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAB Sheet 01, Fig. A-UBBAB Sheet 03, View C and Fig. A-UBCAB Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal
.

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 350

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAB Sheet 01
and Fig. A-UBBAB Sheet 03, View C.

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAB Sheet 01, View
A and Fig. A-UBBAB Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAB Sheet 01 and Fig.
A-UBBAB Sheet 03, View C.

20 Install, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAB Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 351

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet
02, View B and Fig. A-UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B
and Fig. A-UBBAB Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN(300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 352

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

30 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAB Sheet 01,
View A and Fig. A-UBBAB Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer to Fig.
A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-
UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAB
Sheet 01 and Fig. A-UBBAB Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAB Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 353

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAB Sheet 02, View B.

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAB Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAB Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAB Sheet 01, View
A, Fig. A-UBBAB Sheet 02, View B, Fig. A-UBBAB Sheet 03, View C and Fig.
A-UBDAB Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 354

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(6) Subtask 521165-420-402-002 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 355

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-UBBAB
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 356

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAB Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBBAB Sheet 02, Fig. A-UBBAB Sheet 03 and Fig. A-UBBAB Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAB Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAB Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 357

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

6 Install, refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 358

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAB Sheet 01, Fig. A-UBBAB Sheet 03, View C and Fig. A-UBCAB Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAB Sheet 01
and Fig. A-UBBAB Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 359

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAB Sheet 01, View
A and Fig. A-UBBAB Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAB Sheet 01 and Fig.
A-UBBAB Sheet 03, View C.

20 Install, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAB Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 360

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet
02, View B and Fig. A-UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B
and Fig. A-UBBAB Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

30 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 361

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAB Sheet 01,
View A and Fig. A-UBBAB Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer to Fig.
A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-
UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAB
Sheet 01 and Fig. A-UBBAB Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAB Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAB Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 362

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAB Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAB Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAB Sheet 01, View
A, Fig. A-UBBAB Sheet 02, View B, Fig. A-UBBAB Sheet 03, View C and Fig.
A-UBDAB Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 363

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(7) Subtask 521165-930-401-005 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB03

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285300300095 FAIRING (15) D5285300300000

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 364

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBCAB Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285300300000 Item (15)

becomes:

1 Fairing Assembly D5285300300095 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 365

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(8) Subtask 521165-930-402-005 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB03

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285300300195 FAIRING (15) D5285300300100

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 366

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBCAB Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285300300100 Item (15)

becomes:

1 Fairing Assembly D5285300300195 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 367

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 009

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(3) Subtask 521165-960-401-005 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 368

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001
Task 32-12-14-400-002
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAD Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAD Sheet 01.

2 Nut NAS509-8 Item (3) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 369

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 370

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-004 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 371

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAD Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAD Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 372

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 373

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

They will be torque tightened during the installation of the MLG

fixed fairing assembly procedure.

(5) Subtask 521165-420-401-004 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Top Coat Polyurethane- 04JMD3 As required
Decorative External Struc
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Polysulfide Sealant-Low 06AEA1 As required
Adhesion Brushable
Polysulfide Sealant-Low 06AEB2 As required
Adhesion Fillet Structure
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 374

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 375

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-UBBAD
Sheet 03, View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAD Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAD Sheet
01, Fig. A-UBBAD Sheet 02, Fig. A-UBBAD Sheet 03 and Fig. A-UBBAD Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAD Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 376

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

3 Install, refer to Fig. A-UBBAD Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

6 Install, refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet
02, View B:

2 Nut Item (3) Retain

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 377

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAD Sheet 01, Fig. A-UBBAD Sheet 03, View C and Fig. A-UBCAD Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between - 0.00 mm (- 0.000 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates, Item (8), refer to
Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal
.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 378

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer toFig. A-UBBAD Sheet 01
and Fig. A-UBBAD Sheet 03, View C.

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAD Sheet 01, View
A and Fig. A-UBBAD Sheet 02, View B.

16 Refer to Fig. A-UBCAD Sheet 01 and Fig. A-UBCAD Sheet 02, adjust the 1A
fairing, item 32, as follows:

a Measure the dimension A and make sure that the dimension is a

maximum of 3.00 mm (0.118 in.).

b If necessary, adjust the position of the 1A extension, item 32, as follows:

- Loosen the bolts, items 33 and 35 and nuts, item 34.

- Adjust the 1A fairing item, 32, to get dimension A.

c Torque the bolts, items 33 and 35 and nuts, item 34 to between 0.7
m.daN (61.95 lbf in.) and 0.8 m.daN (70.80 lbf in.).

d Apply sealant to bolts, items 33 and 35 and nuts, item 34, Fig. A-UBCAD
Sheet 02.

use:

Polysulfide Sealant- 06AEA1 As required

Low Adhesion
Brushable
or

Polysulfide Sealant- 06AEB2 As required

Low Adhesion Fillet
Structure

e Mark three black lines on the MLG fixed fairing, refer toFig. A-UBBAD
Sheet 01, item 15

and Fig. A-UBCAD Sheet 02

use:

Top Coat 04JMD3 As required

Polyurethane-
Decorative External
Struc

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 379

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

17 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

NOTE: Do not final torque at this stage.

18 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

19 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

20 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAD Sheet 01 and Fig.
A-UBBAD Sheet 03, View C.

21 Install, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

22 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAD Sheet 03, View F.

23

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

24 Remove from the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

25 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 380

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

26 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

27

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

28 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet
02, View B and Fig. A-UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

29 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B
and Fig. A-UBBAD Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

30 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.328 lbf in.).

31 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

32

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 381

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

33 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAD Sheet 01,
View A and Fig. A-UBBAD Sheet 02, View B.

34 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

35 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

36 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer toFig.
A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-
UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

37 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAD
Sheet 01 and Fig. A-UBBAD Sheet 03, View C.

38 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAD Sheet 03, View E.

39

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

40 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAD Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 382

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

41 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01, View A.

42 Safety the nut, Item (19), refer to Fig. A-UBBAD Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

43 Safety the nut, Item (40), refer to Fig. A-UBBAD Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

44 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD
Sheet 03, View C.

45 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

46

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAD Sheet 01, View
A, Fig. A-UBBAD Sheet 02, View B, Fig. A-UBBAD Sheet 03, View C and Fig.
A-UBDAD Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 383

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(6) Subtask 521165-420-402-004 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Top Coat Polyurethane- 04JMD3 As required
Decorative External Struc
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Polysulfide Sealant-Low 06AEA1 As required
Adhesion Brushable
Polysulfide Sealant-Low 06AEB2 As required
Adhesion Fillet Structure
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 384

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-UBBAD
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 385

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAD Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAD Sheet
01, Fig. A-UBBAD Sheet 02, Fig. A-UBBAD Sheet 03 and Fig. A-UBBAD Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAD Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAD Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 386

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

6 Install, refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 387

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAD Sheet 01, Fig. A-UBBAD Sheet 03, View C and Fig. A-UBCAD Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between - 0.00 mm (+ 0.000 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates, Item (8), refer to
Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer toFig. A-UBBAD Sheet 01
and Fig. A-UBBAD Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 388

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAD Sheet 01, View
A and Fig. A-UBBAD Sheet 02, View B.

16 Refer to Fig. A-UBCAD Sheet 01 and Fig. A-UBCAD Sheet 02, adjust the 1A
fairing, item 32, as follows:

a Measure the dimension A and make sure that the dimension is a

maximum of 3 mm (0.118 in.).

b If necessary, adjust the position of the 1A extension, item 32, as follows:

- loosen the bolts, items 33 and 35 and nuts, item 34

- adjust the 1A fairing item, 32, to get dimension A.

c Torque the bolts, items 33 and 35 and nuts, item 34 to between 0.7
m.daN (61.95 lbf in.) and 0.8 m.daN (70.80 lbf in.).

d Apply sealant to bolts, items 33 and 35 and nuts, item 34, Fig. A-UBCAD
Sheet 02.

use:

Polysulfide Sealant- 06AEA1 As required

Low Adhesion
Brushable
or

Polysulfide Sealant- 06AEB2 As required

Low Adhesion Fillet
Structure

e Mark three black lines on the MLG fixed fairing, refer toFig. A-UBBAD
Sheet 01, item 15 and Fig. A-UBCAD Sheet 02

use:

Top Coat 04JMD3 As required

Polyurethane-
Decorative External
Struc

17 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

NOTE: Do not final torque at this stage.

18 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

19 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 389

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

20 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAD Sheet 01 and Fig.
A-UBBAD Sheet 03, View C.

21 Install, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

22 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAD Sheet 03, View F.

23

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

24 Remove from the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

25 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

26 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

27

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 390

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

28 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet
02, View B and Fig. A-UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

29 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B
and Fig. A-UBBAD Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

30 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.328 lbf in.).

31 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

32

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

33 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAD Sheet 01,
View A and Fig. A-UBBAD Sheet 02, View B.

34 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAD Sheet 01.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 391

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

35 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

36 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer toFig.
A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-
UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

37 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAD
Sheet 01 and Fig. A-UBBAD Sheet 03, View C.

38 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAD Sheet 03, View E.

39

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

40 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAD Sheet 02, View B.

41 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01, View A.

42 Safety the nut, Item (19), refer to Fig. A-UBBAD Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

43 Safety the nut, Item (40), refer to Fig. A-UBBAD Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 392

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

44 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD
Sheet 03, View C.

45 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

46

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAD Sheet 01, View
A, Fig. A-UBBAD Sheet 02, View B, Fig. A-UBBAD Sheet 03, View C and Fig.
A-UBDAD Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(7) Subtask 521165-930-401-011 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 393

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB07

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601000295 FAIRING (15) D5285601000200

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows,

refer to Fig. A-UBCAD Sheet 03.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 394

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAD Sheet 01,
Fig. A-UBCAD Sheet 03 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285601000200 Item (15)

becomes:

1 Fairing Assembly D5285601000295 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(8) Subtask 521165-930-402-011 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 395

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB07

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601000395 FAIRING (15) D5285601000300

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAD Sheet 03.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 396

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAD Sheet 01,
Fig. A-UBCAD Sheet 03 and PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285601000300 Item (15)

becomes:

1 Fairing Assembly D5285601000395 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 010

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 397

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(3) Subtask 521165-960-401-005 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 398

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001
Task 32-12-14-400-002
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAD Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAD Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 399

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 400

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-004 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 401

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAD Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAD Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 402

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(5) Subtask 521165-420-401-004 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 403

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Top Coat Polyurethane- 04JMD3 As required
Decorative External Struc
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Polysulfide Sealant-Low 06AEA1 As required
Adhesion Brushable
Polysulfide Sealant-Low 06AEB2 As required
Adhesion Fillet Structure
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 404

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-UBBAD
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 405

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAD Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAD Sheet
01, Fig. A-UBBAD Sheet 02, Fig. A-UBBAD Sheet 03 and Fig. A-UBBAD Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAD Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAD Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 406

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

6 Install, refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 407

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAD Sheet 01, Fig. A-UBBAD Sheet 03, View C and Fig. A-UBCAD Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between - 0.00 mm (- 0.000 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates, Item (8), refer to
Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal
.

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 408

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer toFig. A-UBBAD Sheet 01
and Fig. A-UBBAD Sheet 03, View C.

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAD Sheet 01, View
A and Fig. A-UBBAD Sheet 02, View B.

16 Refer to Fig. A-UBCAD Sheet 01 and Fig. A-UBCAD Sheet 02, adjust the 1A
fairing, item 32, as follows:

a Measure the dimension A and make sure that the dimension is a

maximum of 3.00 mm (0.118 in.).

b If necessary, adjust the position of the 1A extension, item 32, as follows:

- Loosen the bolts, items 33 and 35 and nuts, item 34.

- Adjust the 1A fairing item, 32, to get dimension A.

c Torque the bolts, items 33 and 35 and nuts, item 34 to between 0.7
m.daN (61.95 lbf in.) and 0.8 m.daN (70.80 lbf in.).

d Apply sealant to bolts, items 33 and 35 and nuts, item 34, Fig. A-UBCAD
Sheet 02.

use:

Polysulfide Sealant- 06AEA1 As required

Low Adhesion
Brushable
or

Polysulfide Sealant- 06AEB2 As required

Low Adhesion Fillet
Structure

e Mark three black lines on the MLG fixed fairing, refer toFig. A-UBBAD
Sheet 01, item 15

and Fig. A-UBCAD Sheet 02

use:

Top Coat 04JMD3 As required

Polyurethane-
Decorative External
Struc

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 409

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

17 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

NOTE: Do not final torque at this stage.

18 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

19 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

20 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAD Sheet 01 and Fig.
A-UBBAD Sheet 03, View C.

21 Install, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

22 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAD Sheet 03, View F.

23

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

24 Remove from the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

25 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 410

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

26 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

27

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

28 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet
02, View B and Fig. A-UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

29 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B
and Fig. A-UBBAD Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

30 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.328 lbf in.).

31 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

32

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 411

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

33 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAD Sheet 01,
View A and Fig. A-UBBAD Sheet 02, View B.

34 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

35 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

36 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer toFig.
A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-
UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

37 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAD
Sheet 01 and Fig. A-UBBAD Sheet 03, View C.

38 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAD Sheet 03, View E.

39

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

40 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAD Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 412

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

41 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01, View A.

42 Safety the nut, Item (19), refer to Fig. A-UBBAD Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

43 Safety the nut, Item (40), refer to Fig. A-UBBAD Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

44 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD
Sheet 03, View C.

45 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

46

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAD Sheet 01, View
A, Fig. A-UBBAD Sheet 02, View B, Fig. A-UBBAD Sheet 03, View C and Fig.
A-UBDAD Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 413

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(6) Subtask 521165-420-402-004 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Top Coat Polyurethane- 04JMD3 As required
Decorative External Struc
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Polysulfide Sealant-Low 06AEA1 As required
Adhesion Brushable
Polysulfide Sealant-Low 06AEB2 As required
Adhesion Fillet Structure
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 414

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-UBBAD
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 415

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAD Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAD Sheet
01, Fig. A-UBBAD Sheet 02, Fig. A-UBBAD Sheet 03 and Fig. A-UBBAD Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAD Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAD Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 416

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

6 Install, refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 417

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAD Sheet 01, Fig. A-UBBAD Sheet 03, View C and Fig. A-UBCAD Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between - 0.00 mm (+ 0.000 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates, Item (8), refer to
Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer toFig. A-UBBAD Sheet 01
and Fig. A-UBBAD Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 418

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAD Sheet 01, View
A and Fig. A-UBBAD Sheet 02, View B.

16 Refer to Fig. A-UBCAD Sheet 01 and Fig. A-UBCAD Sheet 02, adjust the 1A
fairing, item 32, as follows:

a Measure the dimension A and make sure that the dimension is a

maximum of 3 mm (0.118 in.).

b If necessary, adjust the position of the 1A extension, item 32, as follows:

- loosen the bolts, items 33 and 35 and nuts, item 34

- adjust the 1A fairing item, 32, to get dimension A.

c Torque the bolts, items 33 and 35 and nuts, item 34 to between 0.7
m.daN (61.95 lbf in.) and 0.8 m.daN (70.80 lbf in.).

d Apply sealant to bolts, items 33 and 35 and nuts, item 34, Fig. A-UBCAD
Sheet 02.

use:

Polysulfide Sealant- 06AEA1 As required

Low Adhesion
Brushable
or

Polysulfide Sealant- 06AEB2 As required

Low Adhesion Fillet
Structure

e Mark three black lines on the MLG fixed fairing, refer toFig. A-UBBAD
Sheet 01, item 15 and Fig. A-UBCAD Sheet 02

use:

Top Coat 04JMD3 As required

Polyurethane-
Decorative External
Struc

17 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

NOTE: Do not final torque at this stage.

18 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

19 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 419

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

20 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAD Sheet 01 and Fig.
A-UBBAD Sheet 03, View C.

21 Install, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

22 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAD Sheet 03, View F.

23

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

24 Remove from the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

25 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

26 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

27

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 420

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

28 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet
02, View B and Fig. A-UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

29 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B
and Fig. A-UBBAD Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

30 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.328 lbf in.).

31 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

32

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

33 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAD Sheet 01,
View A and Fig. A-UBBAD Sheet 02, View B.

34 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAD Sheet 01.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 421

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

35 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

36 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer toFig.
A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-
UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

37 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAD
Sheet 01 and Fig. A-UBBAD Sheet 03, View C.

38 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAD Sheet 03, View E.

39

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

40 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAD Sheet 02, View B.

41 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01, View A.

42 Safety the nut, Item (19), refer to Fig. A-UBBAD Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

43 Safety the nut, Item (40), refer to Fig. A-UBBAD Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 422

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

44 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD
Sheet 03, View C.

45 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

46

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAD Sheet 01, View
A, Fig. A-UBBAD Sheet 02, View B, Fig. A-UBBAD Sheet 03, View C and Fig.
A-UBDAD Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(7) Subtask 521165-930-401-013 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 423

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB08

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601000495 FAIRING (15) D5285601000400

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows,

refer to Fig. A-UBCAD Sheet 03.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 424

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAD Sheet 01,
Fig. A-UBCAD Sheet 03 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285601000400 Item (15)

becomes:

1 Fairing Assembly D5285601000495 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(8) Subtask 521165-930-402-013 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 425

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB08

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601000595 FAIRING (15) D5285601000500

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAD Sheet 03.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 426

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAD Sheet 01,
Fig. A-UBCAD Sheet 03 and PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285601000500 Item (15)

becomes:

1 Fairing Assembly D5285601000595 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 011

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 427

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(3) Subtask 521165-960-401-005 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 428

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001
Task 32-12-14-400-002
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAD Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAD Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 429

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 430

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-004 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 431

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAD Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAD Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 432

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(5) Subtask 521165-420-401-004 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 433

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Top Coat Polyurethane- 04JMD3 As required
Decorative External Struc
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Polysulfide Sealant-Low 06AEA1 As required
Adhesion Brushable
Polysulfide Sealant-Low 06AEB2 As required
Adhesion Fillet Structure
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 434

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-UBBAD
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 435

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAD Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAD Sheet
01, Fig. A-UBBAD Sheet 02, Fig. A-UBBAD Sheet 03 and Fig. A-UBBAD Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAD Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAD Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 436

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

6 Install, refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 437

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAD Sheet 01, Fig. A-UBBAD Sheet 03, View C and Fig. A-UBCAD Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between - 0.00 mm (- 0.000 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates, Item (8), refer to
Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal
.

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 438

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer toFig. A-UBBAD Sheet 01
and Fig. A-UBBAD Sheet 03, View C.

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAD Sheet 01, View
A and Fig. A-UBBAD Sheet 02, View B.

16 Refer to Fig. A-UBCAD Sheet 01 and Fig. A-UBCAD Sheet 02, adjust the 1A
fairing, item 32, as follows:

a Measure the dimension A and make sure that the dimension is a

maximum of 3.00 mm (0.118 in.).

b If necessary, adjust the position of the 1A extension, item 32, as follows:

- Loosen the bolts, items 33 and 35 and nuts, item 34.

- Adjust the 1A fairing item, 32, to get dimension A.

c Torque the bolts, items 33 and 35 and nuts, item 34 to between 0.7
m.daN (61.95 lbf in.) and 0.8 m.daN (70.80 lbf in.).

d Apply sealant to bolts, items 33 and 35 and nuts, item 34, Fig. A-UBCAD
Sheet 02.

use:

Polysulfide Sealant- 06AEA1 As required

Low Adhesion
Brushable
or

Polysulfide Sealant- 06AEB2 As required

Low Adhesion Fillet
Structure

e Mark three black lines on the MLG fixed fairing, refer toFig. A-UBBAD
Sheet 01, item 15

and Fig. A-UBCAD Sheet 02

use:

Top Coat 04JMD3 As required

Polyurethane-
Decorative External
Struc

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 439

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

17 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

NOTE: Do not final torque at this stage.

18 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

19 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

20 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAD Sheet 01 and Fig.
A-UBBAD Sheet 03, View C.

21 Install, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

22 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAD Sheet 03, View F.

23

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

24 Remove from the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

25 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 440

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

26 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

27

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

28 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet
02, View B and Fig. A-UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

29 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B
and Fig. A-UBBAD Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

30 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.328 lbf in.).

31 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

32

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 441

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

33 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAD Sheet 01,
View A and Fig. A-UBBAD Sheet 02, View B.

34 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

35 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

36 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer toFig.
A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-
UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

37 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAD
Sheet 01 and Fig. A-UBBAD Sheet 03, View C.

38 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAD Sheet 03, View E.

39

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

40 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAD Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 442

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

41 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01, View A.

42 Safety the nut, Item (19), refer to Fig. A-UBBAD Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

43 Safety the nut, Item (40), refer to Fig. A-UBBAD Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

44 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD
Sheet 03, View C.

45 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

46

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAD Sheet 01, View
A, Fig. A-UBBAD Sheet 02, View B, Fig. A-UBBAD Sheet 03, View C and Fig.
A-UBDAD Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 443

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(6) Subtask 521165-420-402-004 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Top Coat Polyurethane- 04JMD3 As required
Decorative External Struc
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Polysulfide Sealant-Low 06AEA1 As required
Adhesion Brushable
Polysulfide Sealant-Low 06AEB2 As required
Adhesion Fillet Structure
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 444

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-UBBAD
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 445

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAD Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAD Sheet
01, Fig. A-UBBAD Sheet 02, Fig. A-UBBAD Sheet 03 and Fig. A-UBBAD Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAD Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAD Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 446

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

6 Install, refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 447

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAD Sheet 01, Fig. A-UBBAD Sheet 03, View C and Fig. A-UBCAD Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between - 0.00 mm (+ 0.000 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates, Item (8), refer to
Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer toFig. A-UBBAD Sheet 01
and Fig. A-UBBAD Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 448

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAD Sheet 01, View
A and Fig. A-UBBAD Sheet 02, View B.

16 Refer to Fig. A-UBCAD Sheet 01 and Fig. A-UBCAD Sheet 02, adjust the 1A
fairing, item 32, as follows:

a Measure the dimension A and make sure that the dimension is a

maximum of 3 mm (0.118 in.).

b If necessary, adjust the position of the 1A extension, item 32, as follows:

- loosen the bolts, items 33 and 35 and nuts, item 34

- adjust the 1A fairing item, 32, to get dimension A.

c Torque the bolts, items 33 and 35 and nuts, item 34 to between 0.7
m.daN (61.95 lbf in.) and 0.8 m.daN (70.80 lbf in.).

d Apply sealant to bolts, items 33 and 35 and nuts, item 34, Fig. A-UBCAD
Sheet 02.

use:

Polysulfide Sealant- 06AEA1 As required

Low Adhesion
Brushable
or

Polysulfide Sealant- 06AEB2 As required

Low Adhesion Fillet
Structure

e Mark three black lines on the MLG fixed fairing, refer toFig. A-UBBAD
Sheet 01, item 15 and Fig. A-UBCAD Sheet 02

use:

Top Coat 04JMD3 As required

Polyurethane-
Decorative External
Struc

17 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

NOTE: Do not final torque at this stage.

18 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

19 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 449

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

20 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAD Sheet 01 and Fig.
A-UBBAD Sheet 03, View C.

21 Install, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

22 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAD Sheet 03, View F.

23

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

24 Remove from the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

25 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

26 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

27

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 450

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

28 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet
02, View B and Fig. A-UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

29 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B
and Fig. A-UBBAD Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

30 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.328 lbf in.).

31 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

32

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

33 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAD Sheet 01,
View A and Fig. A-UBBAD Sheet 02, View B.

34 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAD Sheet 01.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 451

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

35 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

36 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer toFig.
A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-
UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

37 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAD
Sheet 01 and Fig. A-UBBAD Sheet 03, View C.

38 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAD Sheet 03, View E.

39

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

40 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAD Sheet 02, View B.

41 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01, View A.

42 Safety the nut, Item (19), refer to Fig. A-UBBAD Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

43 Safety the nut, Item (40), refer to Fig. A-UBBAD Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 452

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

44 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD
Sheet 03, View C.

45 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

46

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAD Sheet 01, View
A, Fig. A-UBBAD Sheet 02, View B, Fig. A-UBBAD Sheet 03, View C and Fig.
A-UBDAD Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(7) Subtask 521165-930-401-017 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 453

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB06

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000295 FAIRING (15) D5285600000200
(15) D5285601000000

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows,

refer to Fig. A-UBCAD Sheet 03.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 454

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAD Sheet 01,
Fig. A-UBCAD Sheet 03 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285600000200 Item (15)

or

1 Fairing Assembly D5285601000000 Item (15)

becomes:

1 Fairing Assembly D5285600000295 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(8) Subtask 521165-930-402-017 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 455

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB06

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000395 FAIRING (15) D5285600000300
(15) D5285601000100

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 456

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAD Sheet 03.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAD Sheet 01,
Fig. A-UBCAD Sheet 03 and PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285600000300 Item (15)

or

1 Fairing Assembly D5285601000100 Item (15)

becomes:

1 Fairing Assembly D5285600000395 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 457

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 012

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(3) Subtask 521165-960-401-002 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 458

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAB Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAB Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 459

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 460

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item 3 and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-002 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 461

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAB Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAB Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 462

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 463

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

They will be torque tightened during the installation of the MLG

fixed fairing assembly procedure.

(5) Subtask 521165-420-401-002 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 464

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-UBBAB
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 465

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAB Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAB Sheet 01.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAB Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAB Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 466

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

6 Install, refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 467

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAB Sheet 01, Fig. A-UBBAB Sheet 03, View C and Fig. A-UBCAB Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal
.

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 468

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAB Sheet 01
and Fig. A-UBBAB Sheet 03, View C.

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAB Sheet 01, View
A and Fig. A-UBBAB Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAB Sheet 01 and Fig.
A-UBBAB Sheet 03, View C.

20 Install, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAB Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 469

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet
02, View B and Fig. A-UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B
and Fig. A-UBBAB Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN(300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 470

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

30 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAB Sheet 01,
View A and Fig. A-UBBAB Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer to Fig.
A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-
UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAB
Sheet 01 and Fig. A-UBBAB Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAB Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 471

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAB Sheet 02, View B.

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAB Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAB Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAB Sheet 01, View
A, Fig. A-UBBAB Sheet 02, View B, Fig. A-UBBAB Sheet 03, View C and Fig.
A-UBDAB Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 472

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(6) Subtask 521165-420-402-002 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 473

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-UBBAB
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 474

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAB Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBBAB Sheet 02, Fig. A-UBBAB Sheet 03 and Fig. A-UBBAB Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAB Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAB Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 475

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

6 Install, refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 476

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAB Sheet 01, Fig. A-UBBAB Sheet 03, View C and Fig. A-UBCAB Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAB Sheet 01
and Fig. A-UBBAB Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 477

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAB Sheet 01, View
A and Fig. A-UBBAB Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAB Sheet 01 and Fig.
A-UBBAB Sheet 03, View C.

20 Install, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAB Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 478

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet
02, View B and Fig. A-UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B
and Fig. A-UBBAB Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

30 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 479

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAB Sheet 01,
View A and Fig. A-UBBAB Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer to Fig.
A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-
UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAB
Sheet 01 and Fig. A-UBBAB Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAB Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAB Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 480

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAB Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAB Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAB Sheet 01, View
A, Fig. A-UBBAB Sheet 02, View B, Fig. A-UBBAB Sheet 03, View C and Fig.
A-UBDAB Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 481

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(7) Subtask 521165-930-401-018 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB05

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5284000000695 FAIRING (15) D5284000000600

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 482

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBCAB Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5284000000600 Item (15)

becomes:

1 Fairing Assembly D5284000000695 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 483

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(8) Subtask 521165-930-402-018 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB05

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5284000000795 FAIRING (15) D5284000000700

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 484

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBCAB Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5284000000700 Item (15)

becomes:

1 Fairing Assembly D5284000000795 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 485

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 013

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(3) Subtask 521165-960-401-002 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 486

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAB Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAB Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 487

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 488

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item 3 and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-002 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 489

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAB Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAB Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 490

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 491

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

They will be torque tightened during the installation of the MLG

fixed fairing assembly procedure.

(5) Subtask 521165-420-401-002 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 492

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-UBBAB
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 493

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAB Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAB Sheet 01.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAB Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAB Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 494

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

6 Install, refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 495

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAB Sheet 01, Fig. A-UBBAB Sheet 03, View C and Fig. A-UBCAB Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal
.

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 496

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAB Sheet 01
and Fig. A-UBBAB Sheet 03, View C.

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAB Sheet 01, View
A and Fig. A-UBBAB Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAB Sheet 01 and Fig.
A-UBBAB Sheet 03, View C.

20 Install, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAB Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 497

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet
02, View B and Fig. A-UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B
and Fig. A-UBBAB Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN(300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 498

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

30 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAB Sheet 01,
View A and Fig. A-UBBAB Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer to Fig.
A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-
UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAB
Sheet 01 and Fig. A-UBBAB Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAB Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 499

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAB Sheet 02, View B.

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAB Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAB Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAB Sheet 01, View
A, Fig. A-UBBAB Sheet 02, View B, Fig. A-UBBAB Sheet 03, View C and Fig.
A-UBDAB Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 500

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(6) Subtask 521165-420-402-002 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 501

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-UBBAB
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 502

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAB Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBBAB Sheet 02, Fig. A-UBBAB Sheet 03 and Fig. A-UBBAB Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAB Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAB Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 503

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

6 Install, refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 504

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAB Sheet 01, Fig. A-UBBAB Sheet 03, View C and Fig. A-UBCAB Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAB Sheet 01
and Fig. A-UBBAB Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 505

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAB Sheet 01, View
A and Fig. A-UBBAB Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAB Sheet 01 and Fig.
A-UBBAB Sheet 03, View C.

20 Install, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAB Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 506

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet
02, View B and Fig. A-UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B
and Fig. A-UBBAB Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

30 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 507

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAB Sheet 01,
View A and Fig. A-UBBAB Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer to Fig.
A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-
UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAB
Sheet 01 and Fig. A-UBBAB Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAB Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAB Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 508

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAB Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAB Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAB Sheet 01, View
A, Fig. A-UBBAB Sheet 02, View B, Fig. A-UBBAB Sheet 03, View C and Fig.
A-UBDAB Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 509

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(7) Subtask 521165-930-401-019 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB08

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601000495 FAIRING (15) D5285601000400

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 510

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows,

refer to Fig. A-UBCAB Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBCAB Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285601000400 Item (15)

becomes:

1 Fairing Assembly D5285601000495 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 511

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(8) Subtask 521165-930-402-019 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB08

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601000595 FAIRING (15) D5285601000500

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 512

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBCAB Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285601000500 Item (15)

becomes:

1 Fairing Assembly D5285601000595 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 513

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 014

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(3) Subtask 521165-960-401-001 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 514

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
8 D5285600620000 2 PLATE
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAA Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAA Sheet 01.

4 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5284000500000 Item (6) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 515

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Rod Assy-End Upper D5284000600000 Item (7) Discard

2 Stud-Adjustment D5284024420000 Item (5) Discard

2 Plate-Support D5284024820200 Item (8) Discard

or

2 Plate-Support D5284024820000 Item (8) Discard

(b) Install on the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

2 Plate-Support D5285600620000 Item 8

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 516

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item 3 and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-001 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
8 D5285600620000 2 PLATE
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 517

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAA Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAA Sheet 01.

4 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5284000500000 Item (6) Discard

1 Rod Assy-End Upper D5284000600000 Item (7) Discard

2 Stud-Adjustment D5284024420000 Item (5) Discard

2 Plate-Support D5284024820200 Item (8) Discard

or

2 Plate-Support D5284024820000 Item (8) Discard

(b) Install on the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

2 Plate-Support D5285600620000 Item 8

2 Stud Adjustment D5285610020000 Item 5

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 518

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 519

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(5) Subtask 521165-420-401-001 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 520

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-UBBAA
Sheet 03 View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 521

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAA Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBBAA Sheet 02, Fig. A-UBBAA Sheet 03 and Fig. A-UBBAA Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAA Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAA Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 522

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

6 Install, refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficient enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAA Sheet 01, Fig. A-UBBAA Sheet 03, View C and Fig. A-UBCAA Sheet
01

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 523

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- at position H, dimension T between + 0.00mm (+ 0.00 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.00 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7), until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAA Sheet 01
and Fig. A-UBBAA Sheet 03, View C.

15 If it is necessary, adjust each stud Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAA Sheet 01, View
A and Fig. A-UBBAA Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 524

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAA Sheet 01 and Fig.
A-UBBAA Sheet 03, View C.

20 Install, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAA Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 525

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet
02, View B and Fig. A-UBDAA Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B
and Fig. A-UBBAA Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6), and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

30 Make sure that the rod-ends, Item (6), and (7), are parallel to the MLG bracket
lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 526

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAA Sheet 01,
View A and Fig. A-UBBAA Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24), and screws, Item (25), refer to
Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-
UBDAA Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAA
Sheet 01 and Fig. A-UBBAA Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAA Sheet 01 andFig. A-UBBAA Sheet 03, View C and
View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAA Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 527

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAA Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAA Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAA Sheet 01, View
A, Fig. A-UBBAA Sheet 02, View B, Fig. A-UBBAA Sheet 03, View C and Fig.
A-UBDAA Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of adjuster (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 528

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(6) Subtask 521165-420-402-001 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 529

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-UBBAA
Sheet 03, View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 530

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAA Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBBAA Sheet 02, Fig. A-UBBAA Sheet 03 and Fig. A-UBBAA Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAA Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAA Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 531

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

6 Install, refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficient enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAA Sheet 01, Fig. A-UBBAA Sheet 03, View C and Fig. A-UBCAA Sheet
01

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 532

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- at position H, dimension T between + 0.000 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.00 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7), until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAA Sheet 01
and Fig. A-UBBAA Sheet 03, View C.

15 If it is necessary, adjust each stud Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAA Sheet 01, View
A and Fig. A-UBBAA Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 533

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAA Sheet 01 and Fig.
A-UBBAA Sheet 03, View C.

20 Install, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAA Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 534

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

25 Torque the nuts, Item (3), to between 4.0 m.daN (354.02 lbf in.) and 4.30
m.daN (380.58 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-
UBBAA Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet
02, View B and Fig. A-UBDAA Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B
and Fig. A-UBBAA Sheet 03, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6), and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

30 Make sure that the rod-ends, Item (6), and (7), are parallel to the MLG bracket
lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 535

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAA Sheet 01,
View A and Fig. A-UBBAA Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24), and screws, Item (25), refer to
Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-
UBDAA Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAA
Sheet 01 and Fig. A-UBBAA Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAA Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 536

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAA Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAA Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAA Sheet 01, View
A, Fig. A-UBBAA Sheet 02, View B, Fig. A-UBBAA Sheet 03, View C and Fig.
A-UBDAA Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of adjuster (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 537

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(7) Subtask 521165-930-401-020 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB09

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000095 FAIRING (15) D5285600000000

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 538

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBCAA Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285600000000 Item (15)

becomes:

1 Fairing Assembly D5285600000095 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 539

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(8) Subtask 521165-930-402-020 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB09

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000195 FAIRING (15) D5285600000100

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 540

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBCAA Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing assembly D5285600000100 Item (15)

becomes:

1 Fairing Assembly D5285600000195 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 541

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 015

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(3) Subtask 521165-960-401-001 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 542

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
8 D5285600620000 2 PLATE
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAA Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAA Sheet 01.

4 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5284000500000 Item (6) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 543

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Rod Assy-End Upper D5284000600000 Item (7) Discard

2 Stud-Adjustment D5284024420000 Item (5) Discard

2 Plate-Support D5284024820200 Item (8) Discard

or

2 Plate-Support D5284024820000 Item (8) Discard

(b) Install on the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

2 Plate-Support D5285600620000 Item 8

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 544

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item 3 and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-001 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
8 D5285600620000 2 PLATE
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 545

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAA Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAA Sheet 01.

4 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5284000500000 Item (6) Discard

1 Rod Assy-End Upper D5284000600000 Item (7) Discard

2 Stud-Adjustment D5284024420000 Item (5) Discard

2 Plate-Support D5284024820200 Item (8) Discard

or

2 Plate-Support D5284024820000 Item (8) Discard

(b) Install on the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

2 Plate-Support D5285600620000 Item 8

2 Stud Adjustment D5285610020000 Item 5

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 546

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 547

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(5) Subtask 521165-420-401-001 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 548

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-UBBAA
Sheet 03 View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 549

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAA Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBBAA Sheet 02, Fig. A-UBBAA Sheet 03 and Fig. A-UBBAA Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAA Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAA Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 550

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

6 Install, refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficient enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAA Sheet 01, Fig. A-UBBAA Sheet 03, View C and Fig. A-UBCAA Sheet
01

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 551

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- at position H, dimension T between + 0.00mm (+ 0.00 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.00 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7), until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAA Sheet 01
and Fig. A-UBBAA Sheet 03, View C.

15 If it is necessary, adjust each stud Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAA Sheet 01, View
A and Fig. A-UBBAA Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 552

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAA Sheet 01 and Fig.
A-UBBAA Sheet 03, View C.

20 Install, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAA Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 553

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet
02, View B and Fig. A-UBDAA Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B
and Fig. A-UBBAA Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6), and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

30 Make sure that the rod-ends, Item (6), and (7), are parallel to the MLG bracket
lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 554

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAA Sheet 01,
View A and Fig. A-UBBAA Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24), and screws, Item (25), refer to
Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-
UBDAA Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAA
Sheet 01 and Fig. A-UBBAA Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAA Sheet 01 andFig. A-UBBAA Sheet 03, View C and
View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAA Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 555

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAA Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAA Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAA Sheet 01, View
A, Fig. A-UBBAA Sheet 02, View B, Fig. A-UBBAA Sheet 03, View C and Fig.
A-UBDAA Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of adjuster (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 556

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(6) Subtask 521165-420-402-001 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 557

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-UBBAA
Sheet 03, View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 558

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAA Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBBAA Sheet 02, Fig. A-UBBAA Sheet 03 and Fig. A-UBBAA Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAA Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAA Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 559

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

6 Install, refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficient enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAA Sheet 01, Fig. A-UBBAA Sheet 03, View C and Fig. A-UBCAA Sheet
01

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 560

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- at position H, dimension T between + 0.000 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.00 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7), until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAA Sheet 01
and Fig. A-UBBAA Sheet 03, View C.

15 If it is necessary, adjust each stud Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAA Sheet 01, View
A and Fig. A-UBBAA Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 561

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAA
Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAA Sheet 01 and Fig.
A-UBBAA Sheet 03, View C.

20 Install, refer to Fig. A-UBBAA Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAA Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAA Sheet 01, View A and
Fig. A-UBBAA Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig.
A-UBBAA Sheet 04, View G.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 562

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

25 Torque the nuts, Item (3), to between 4.0 m.daN (354.02 lbf in.) and 4.30
m.daN (380.58 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A and Fig. A-
UBBAA Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet
02, View B and Fig. A-UBDAA Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B
and Fig. A-UBBAA Sheet 03, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6), and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

30 Make sure that the rod-ends, Item (6), and (7), are parallel to the MLG bracket
lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 563

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAA Sheet 01,
View A and Fig. A-UBBAA Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAA Sheet 01, View A and Fig. A-UBBAA Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24), and screws, Item (25), refer to
Fig. A-UBBAA Sheet 01, View A, Fig. A-UBBAA Sheet 02, View B and Fig. A-
UBDAA Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAA
Sheet 01 and Fig. A-UBBAA Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAA Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 564

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAA Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAA Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAA Sheet 01 and Fig. A-UBBAA
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAA Sheet 01, View
A, Fig. A-UBBAA Sheet 02, View B, Fig. A-UBBAA Sheet 03, View C and Fig.
A-UBDAA Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of adjuster (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 565

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(7) Subtask 521165-930-401-021 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB10

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000295 FAIRING (15) D5285600000200

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 566

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBCAA Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285600000200 Item (15)

becomes:

1 Fairing Assembly D5285600000295 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 567

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(8) Subtask 521165-930-402-021 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B01R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB10

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000395 FAIRING (15) D5285600000300

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAA Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAA Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 568

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAA Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAA Sheet 01,
Fig. A-UBCAA Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285600000300 Item (15)

becomes:

1 Fairing Assembly D5285600000395 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 569

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 016

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(3) Subtask 521165-960-401-002 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 570

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAB Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAB Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 571

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 572

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item 3 and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-002 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 573

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAB Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAB Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 574

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 575

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

They will be torque tightened during the installation of the MLG

fixed fairing assembly procedure.

(5) Subtask 521165-420-401-002 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 576

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-UBBAB
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 577

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAB Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAB Sheet 01.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAB Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAB Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 578

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

6 Install, refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 579

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAB Sheet 01, Fig. A-UBBAB Sheet 03, View C and Fig. A-UBCAB Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal
.

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 580

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAB Sheet 01
and Fig. A-UBBAB Sheet 03, View C.

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAB Sheet 01, View
A and Fig. A-UBBAB Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAB Sheet 01 and Fig.
A-UBBAB Sheet 03, View C.

20 Install, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAB Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 581

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet
02, View B and Fig. A-UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B
and Fig. A-UBBAB Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN(300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 582

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

30 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAB Sheet 01,
View A and Fig. A-UBBAB Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer to Fig.
A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-
UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAB
Sheet 01 and Fig. A-UBBAB Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAB Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 583

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAB Sheet 02, View B.

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAB Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAB Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAB Sheet 01, View
A, Fig. A-UBBAB Sheet 02, View B, Fig. A-UBBAB Sheet 03, View C and Fig.
A-UBDAB Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 584

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(6) Subtask 521165-420-402-002 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 585

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-UBBAB
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 586

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAB Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBBAB Sheet 02, Fig. A-UBBAB Sheet 03 and Fig. A-UBBAB Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAB Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAB Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 587

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

6 Install, refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 588

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAB Sheet 01, Fig. A-UBBAB Sheet 03, View C and Fig. A-UBCAB Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAB Sheet 01
and Fig. A-UBBAB Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 589

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAB Sheet 01, View
A and Fig. A-UBBAB Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAB Sheet 01 and Fig.
A-UBBAB Sheet 03, View C.

20 Install, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAB Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 590

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet
02, View B and Fig. A-UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B
and Fig. A-UBBAB Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

30 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 591

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAB Sheet 01,
View A and Fig. A-UBBAB Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer to Fig.
A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-
UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAB
Sheet 01 and Fig. A-UBBAB Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAB Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAB Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 592

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAB Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAB Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAB Sheet 01, View
A, Fig. A-UBBAB Sheet 02, View B, Fig. A-UBBAB Sheet 03, View C and Fig.
A-UBDAB Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 593

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(7) Subtask 521165-930-401-022 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB04

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000095 FAIRING (15) D5285600000000
15 D5285875100095 FAIRING (15) D5285875100000

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 594

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows,

refer to Fig. A-UBCAB Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBCAB Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285600000000 Item (15)

becomes:

1 Fairing Assembly D5285600000095 Item 15

or

1 Fairing Assembly D5285875100000 Item (15)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 595

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

becomes:

1 Fairing Assembly D5285875100095 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(8) Subtask 521165-930-402-022 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB04

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000195 FAIRING (15) D5285600000100
15 D5285875100195 FAIRING (15) D5285875100100

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 596

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBCAB Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing assembly D5285600000100 Item (15)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 597

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

becomes:

1 Fairing Assembly D5285600000195 Item 15

or

1 Fairing Assembly D5285875100100 Item (15)

becomes:

1 Fairing Assembly D5285875100195 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 017

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 598

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(3) Subtask 521165-960-401-002 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 599

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAB Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAB Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 600

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item 3 and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-002 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 601

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAB Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAB Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 602

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 603

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(5) Subtask 521165-420-401-002 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 604

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE

CML MAT. No. NOTES
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 605

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-UBBAB
Sheet 03, View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAB Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAB Sheet 01.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAB Sheet 02, View B:

1 Bush Item (16) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 606

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAB Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

6 Install, refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 607

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAB Sheet 01, Fig. A-UBBAB Sheet 03, View C and Fig. A-UBCAB Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 608

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal
.

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAB Sheet 01
and Fig. A-UBBAB Sheet 03, View C.

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAB Sheet 01, View
A and Fig. A-UBBAB Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAB Sheet 01 and Fig.
A-UBBAB Sheet 03, View C.

20 Install, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAB Sheet 03, View F.

22

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 609

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet
02, View B and Fig. A-UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 610

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B
and Fig. A-UBBAB Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN(300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

30 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAB Sheet 01,
View A and Fig. A-UBBAB Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer to Fig.
A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-
UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAB
Sheet 01 and Fig. A-UBBAB Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 611

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAB Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAB Sheet 02, View B.

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAB Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAB Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAB Sheet 01, View
A, Fig. A-UBBAB Sheet 02, View B, Fig. A-UBBAB Sheet 03, View C and Fig.
A-UBDAB Sheet 01.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 612

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(6) Subtask 521165-420-402-002 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 613

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 614

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-UBBAB
Sheet 03, View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAB Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBBAB Sheet 02, Fig. A-UBBAB Sheet 03 and Fig. A-UBBAB Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAB Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 615

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

3 Install, refer to Fig. A-UBBAB Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

6 Install, refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet
02, View B:

2 Nut Item (3) Retain

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 616

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAB Sheet 01, Fig. A-UBBAB Sheet 03, View C and Fig. A-UBCAB Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 617

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAB Sheet 01
and Fig. A-UBBAB Sheet 03, View C.

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAB Sheet 01, View
A and Fig. A-UBBAB Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAB Sheet 01 and Fig.
A-UBBAB Sheet 03, View C.

20 Install, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAB Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 618

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet
02, View B and Fig. A-UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B
and Fig. A-UBBAB Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 619

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

30 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAB Sheet 01,
View A and Fig. A-UBBAB Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer to Fig.
A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-
UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAB
Sheet 01 and Fig. A-UBBAB Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAB Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 620

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAB Sheet 02, View B.

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAB Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAB Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAB Sheet 01, View
A, Fig. A-UBBAB Sheet 02, View B, Fig. A-UBBAB Sheet 03, View C and Fig.
A-UBDAB Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 621

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(7) Subtask 521165-930-401-023 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB06

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000295 FAIRING (15) D5285600000200
(15) D5285601000000

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 622

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows,

refer to Fig. A-UBCAB Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBCAB Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285600000200 Item (15)

or

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 623

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Fairing Assembly D5285601000000 Item (15)

becomes:

1 Fairing Assembly D5285600000295 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(8) Subtask 521165-930-402-023 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB06

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000395 FAIRING (15) D5285600000300
(15) D5285601000100

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 624

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBCAB Sheet 02 and PMS 01-06-13.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 625

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285600000300 Item (15)

or

1 Fairing Assembly D5285601000100 Item (15)

becomes:

1 Fairing Assembly D5285600000395 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 018

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 626

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(3) Subtask 521165-960-401-002 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 627

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAB Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAB Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 628

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item 3 and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-002 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 629

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAB Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAB Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 630

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 631

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(5) Subtask 521165-420-401-002 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 632

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE

CML MAT. No. NOTES
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 633

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-UBBAB
Sheet 03, View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAB Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAB Sheet 01.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAB Sheet 02, View B:

1 Bush Item (16) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 634

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAB Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

6 Install, refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 635

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAB Sheet 01, Fig. A-UBBAB Sheet 03, View C and Fig. A-UBCAB Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 636

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal
.

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAB Sheet 01
and Fig. A-UBBAB Sheet 03, View C.

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAB Sheet 01, View
A and Fig. A-UBBAB Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAB Sheet 01 and Fig.
A-UBBAB Sheet 03, View C.

20 Install, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAB Sheet 03, View F.

22

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 637

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet
02, View B and Fig. A-UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 638

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B
and Fig. A-UBBAB Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN(300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

30 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAB Sheet 01,
View A and Fig. A-UBBAB Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer to Fig.
A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-
UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAB
Sheet 01 and Fig. A-UBBAB Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 639

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAB Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAB Sheet 02, View B.

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAB Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAB Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAB Sheet 01, View
A, Fig. A-UBBAB Sheet 02, View B, Fig. A-UBBAB Sheet 03, View C and Fig.
A-UBDAB Sheet 01.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 640

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(6) Subtask 521165-420-402-002 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 641

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 642

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-UBBAB
Sheet 03, View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAB Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBBAB Sheet 02, Fig. A-UBBAB Sheet 03 and Fig. A-UBBAB Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAB Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 643

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

3 Install, refer to Fig. A-UBBAB Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

6 Install, refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet
02, View B:

2 Nut Item (3) Retain

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 644

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAB Sheet 01, Fig. A-UBBAB Sheet 03, View C and Fig. A-UBCAB Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 645

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAB Sheet 01
and Fig. A-UBBAB Sheet 03, View C.

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAB Sheet 01, View
A and Fig. A-UBBAB Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAB Sheet 01 and Fig.
A-UBBAB Sheet 03, View C.

20 Install, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAB Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 646

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet
02, View B and Fig. A-UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B
and Fig. A-UBBAB Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 647

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

30 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAB Sheet 01,
View A and Fig. A-UBBAB Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer to Fig.
A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-
UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAB
Sheet 01 and Fig. A-UBBAB Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAB Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 648

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAB Sheet 02, View B.

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAB Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAB Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAB Sheet 01, View
A, Fig. A-UBBAB Sheet 02, View B, Fig. A-UBBAB Sheet 03, View C and Fig.
A-UBDAB Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 649

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(7) Subtask 521165-930-401-024 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB07

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601000295 FAIRING (15) D5285601000200

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 650

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows,

refer to Fig. A-UBCAB Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBCAB Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285601000200 Item (15)

becomes:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 651

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Fairing Assembly D5285601000295 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(8) Subtask 521165-930-402-024 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB07

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601000395 FAIRING (15) D5285601000300

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 652

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBCAB Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285601000300 Item (15)

becomes:

1 Fairing Assembly D5285601000395 Item 15

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 653

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 019

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(3) Subtask 521165-960-401-005 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 654

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001
Task 32-12-14-400-002
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 655

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAD Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAD Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 656

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-004 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 657

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAD Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAD Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 658

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 659

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(5) Subtask 521165-420-401-004 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Top Coat Polyurethane- 04JMD3 As required
Decorative External Struc
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Polysulfide Sealant-Low 06AEA1 As required
Adhesion Brushable
Polysulfide Sealant-Low 06AEB2 As required
Adhesion Fillet Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 660

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE

CML MAT. No. NOTES
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 661

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-UBBAD
Sheet 03, View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAD Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAD Sheet
01, Fig. A-UBBAD Sheet 02, Fig. A-UBBAD Sheet 03 and Fig. A-UBBAD Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 662

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Install, refer to Fig. A-UBBAD Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAD Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

6 Install, refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 663

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAD Sheet 01, Fig. A-UBBAD Sheet 03, View C and Fig. A-UBCAD Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between - 0.00 mm (- 0.000 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 664

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates, Item (8), refer to
Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal
.

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer toFig. A-UBBAD Sheet 01
and Fig. A-UBBAD Sheet 03, View C.

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAD Sheet 01, View
A and Fig. A-UBBAD Sheet 02, View B.

16 Refer to Fig. A-UBCAD Sheet 01 and Fig. A-UBCAD Sheet 02, adjust the 1A
fairing, item 32, as follows:

a Measure the dimension A and make sure that the dimension is a

maximum of 3.00 mm (0.118 in.).

b If necessary, adjust the position of the 1A extension, item 32, as follows:

- Loosen the bolts, items 33 and 35 and nuts, item 34.

- Adjust the 1A fairing item, 32, to get dimension A.

c Torque the bolts, items 33 and 35 and nuts, item 34 to between 0.7
m.daN (61.95 lbf in.) and 0.8 m.daN (70.80 lbf in.).

d Apply sealant to bolts, items 33 and 35 and nuts, item 34, Fig. A-UBCAD
Sheet 02.

use:

Polysulfide Sealant- 06AEA1 As required

Low Adhesion
Brushable
or

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 665

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Polysulfide Sealant- 06AEB2 As required

Low Adhesion Fillet
Structure

e Mark three black lines on the MLG fixed fairing, refer toFig. A-UBBAD
Sheet 01, item 15

and Fig. A-UBCAD Sheet 02

use:

Top Coat 04JMD3 As required

Polyurethane-
Decorative External
Struc

17 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

NOTE: Do not final torque at this stage.

18 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

19 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

20 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAD Sheet 01 and Fig.
A-UBBAD Sheet 03, View C.

21 Install, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

22 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAD Sheet 03, View F.

23

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 666

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

24 Remove from the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

25 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

26 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

27

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

28 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet
02, View B and Fig. A-UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

29 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B
and Fig. A-UBBAD Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

30 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.328 lbf in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 667

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

31 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

32

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

33 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAD Sheet 01,
View A and Fig. A-UBBAD Sheet 02, View B.

34 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

35 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

36 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer toFig.
A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-
UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

37 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAD
Sheet 01 and Fig. A-UBBAD Sheet 03, View C.

38 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAD Sheet 03, View E.

39

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 668

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

40 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAD Sheet 02, View B.

41 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01, View A.

42 Safety the nut, Item (19), refer to Fig. A-UBBAD Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

43 Safety the nut, Item (40), refer to Fig. A-UBBAD Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

44 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD
Sheet 03, View C.

45 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

46

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAD Sheet 01, View
A, Fig. A-UBBAD Sheet 02, View B, Fig. A-UBBAD Sheet 03, View C and Fig.
A-UBDAD Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 669

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(6) Subtask 521165-420-402-004 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Top Coat Polyurethane- 04JMD3 As required
Decorative External Struc
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Polysulfide Sealant-Low 06AEA1 As required
Adhesion Brushable
Polysulfide Sealant-Low 06AEB2 As required
Adhesion Fillet Structure
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 670

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 671

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-UBBAD
Sheet 03, View C.

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAD Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAD Sheet
01, Fig. A-UBBAD Sheet 02, Fig. A-UBBAD Sheet 03 and Fig. A-UBBAD Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAD Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 672

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

3 Install, refer to Fig. A-UBBAD Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

6 Install, refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet
02, View B:

2 Nut Item (3) Retain

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 673

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAD Sheet 01, Fig. A-UBBAD Sheet 03, View C and Fig. A-UBCAD Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between - 0.00 mm (+ 0.000 in.) and - 4.50 mm

(- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates, Item (8), refer to
Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 674

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer toFig. A-UBBAD Sheet 01
and Fig. A-UBBAD Sheet 03, View C.

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAD Sheet 01, View
A and Fig. A-UBBAD Sheet 02, View B.

16 Refer to Fig. A-UBCAD Sheet 01 and Fig. A-UBCAD Sheet 02, adjust the 1A
fairing, item 32, as follows:

a Measure the dimension A and make sure that the dimension is a

maximum of 3 mm (0.118 in.).

b If necessary, adjust the position of the 1A extension, item 32, as follows:

- loosen the bolts, items 33 and 35 and nuts, item 34

- adjust the 1A fairing item, 32, to get dimension A.

c Torque the bolts, items 33 and 35 and nuts, item 34 to between 0.7
m.daN (61.95 lbf in.) and 0.8 m.daN (70.80 lbf in.).

d Apply sealant to bolts, items 33 and 35 and nuts, item 34, Fig. A-UBCAD
Sheet 02.

use:

Polysulfide Sealant- 06AEA1 As required

Low Adhesion
Brushable
or

Polysulfide Sealant- 06AEB2 As required

Low Adhesion Fillet
Structure

e Mark three black lines on the MLG fixed fairing, refer toFig. A-UBBAD
Sheet 01, item 15 and Fig. A-UBCAD Sheet 02

use:

Top Coat 04JMD3 As required

Polyurethane-
Decorative External
Struc

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 675

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

17 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAD
Sheet 01, View A and Fig. A-UBBAD Sheet 02, View B.

NOTE: Do not final torque at this stage.

18 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

19 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

20 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAD Sheet 01 and Fig.
A-UBBAD Sheet 03, View C.

21 Install, refer to Fig. A-UBBAD Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

22 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAD Sheet 03, View F.

23

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

24 Remove from the bolt, Item (17), refer to Fig. A-UBBAD Sheet 01, View A and
Fig. A-UBBAD Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

25 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig.
A-UBBAD Sheet 04, View G.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 676

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

26 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAD Sheet 01, View A and Fig. A-UBBAD
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

27

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

28 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet
02, View B and Fig. A-UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

29 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B
and Fig. A-UBBAD Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

30 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.328 lbf in.).

31 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

32

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 677

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

33 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAD Sheet 01,
View A and Fig. A-UBBAD Sheet 02, View B.

34 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAD Sheet 01.

35 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

36 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer toFig.
A-UBBAD Sheet 01, View A, Fig. A-UBBAD Sheet 02, View B and Fig. A-
UBDAD Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

37 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAD
Sheet 01 and Fig. A-UBBAD Sheet 03, View C.

38 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAD Sheet 03, View E.

39

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

40 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAD Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 678

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

41 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01, View A.

42 Safety the nut, Item (19), refer to Fig. A-UBBAD Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

43 Safety the nut, Item (40), refer to Fig. A-UBBAD Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

44 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAD Sheet 01 and Fig. A-UBBAD
Sheet 03, View C.

45 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

46

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAD Sheet 01, View
A, Fig. A-UBBAD Sheet 02, View B, Fig. A-UBBAD Sheet 03, View C and Fig.
A-UBDAD Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 679

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(7) Subtask 521165-930-401-015 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB01

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601001000 FAIRING (15) D5285601000600

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 680

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows,

refer to Fig. A-UBCAD Sheet 03.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAD Sheet 01,
Fig. A-UBCAD Sheet 03 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285601000600 Item (15)

becomes:

1 Fairing Assembly D5285601001000 Item 15

6 Apply varnish to the identification plate, item 36.

Use

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 681

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Coating - Flexible 04QAB2 As required

Structure

(8) Subtask 521165-930-402-015 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB01

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601001100 FAIRING (15) D5285601000700

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAD Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAD Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 682

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03
Fig. A-UBDAD Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAD Sheet 03.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAD Sheet 01,
Fig. A-UBCAD Sheet 03 and PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285601000700 Item (15)

becomes:

1 Fairing Assembly D5285601001100 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 683

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 020

(1) Subtask 521165-020-402-001 - Remove the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the LH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(2) Subtask 521165-020-403-001 - Remove the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-000-001

Remove the RH MLG Fixed Fairing Assembly, refer to AMM Task 32-12-14-000-001.

(3) Subtask 521165-960-401-002 - Replace the LH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 684

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Replace the LH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAB Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAB Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 685

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 686

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item 3 and Item 9, at this stage.
They will be torque tightened during the installation of the MLG
fixed fairing assembly procedure.

(4) Subtask 521165-960-402-002 - Replace the RH MLG Fixed Fairing Assembly Upper
and Lower Forward Attachment Studs

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 1.00
Minimum number of person 2
Subtask elapsed time 0.50
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1193K8CP 2 LOCKDVC
3 NAS509-8 2 NUT
5 D5285610020000 2 STUD ADJ
6 D5285600400200 1 ROD END
7 D5285600500200 1 ROD END
9 NAS509-9 2 NUT

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 687

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Synthetic Oil Base Grease- 03GBC1 As required
General Purpose Lithium

References
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

(a) Replace the RH MLG Fixed Fairing Assembly upper and lower forward attachment
studs as follows:

1 Remove and discard the lockwire between the nut, Item (3) and the locking
device, Item (1), refer to Fig. A-UBAAB Sheet 01.

2 Remove from the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBAAB Sheet 01.

2 Nut NAS509-8 Item (3) Discard

2 Locking Device NAS1193K8-2P Item (2) Discard

2 Locking Device NAS1193K8-1P Item (1) Discard

2 Plate-Serrated D5284024620600 Item (4) Retain

1 Rod Assy-End Lower D5285600400000 Item (6) Discard

1 Rod Assy-End Upper D5285600500000 Item (7) Discard

2 Nut NAS1423-9 Item (9) Discard

2 Stud-Adjustment D5285600720000 Item (5) Discard

2 Plate-Support D5285600620000 Item (8) Retain

(b) Install to the MLG Fixed Fairing Assembly the items that follow:

Refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 688

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Plate-Support D5285600620000 Item (8) Retained at

removal

2 Stud Adjustment D5285610020000 Item 5

2 Plate-Serrated D5284024620600 Item (4) Retained at

removal

2 Locking Device NAS1193K8CP Item 1

2 Nut NAS509-8 Item 3

1 Apply:

Synthetic Oil Base 03GBC1 As required

Grease-General
Purpose Lithium

to

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

2 Install:

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Nut NAS509-9 Item 9

on

1 Rod End-Assy Upper D5285600500200 Item 7

3 Install:

1 Rod End-Assy Lower D5285600400200 Item 6

and

1 Rod End-Assy Upper D5285600500200 Item 7

into

2 Stud Adjustment D5285610020000 Item 5

NOTE: Do not tighten the lock nuts, Item (3) and Item 9, at this stage.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 689

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

They will be torque tightened during the installation of the MLG

fixed fairing assembly procedure.

(5) Subtask 521165-420-401-002 - Install the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 690

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-UBBAB
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 691

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAB Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAB Sheet 01.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAB Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAB Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 692

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

6 Install, refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 693

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAB Sheet 01, Fig. A-UBBAB Sheet 03, View C and Fig. A-UBCAB Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal
.

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 694

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAB Sheet 01
and Fig. A-UBBAB Sheet 03, View C.

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAB Sheet 01, View
A and Fig. A-UBBAB Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAB Sheet 01 and Fig.
A-UBBAB Sheet 03, View C.

20 Install, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAB Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 695

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet
02, View B and Fig. A-UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B
and Fig. A-UBBAB Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN(300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 696

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

30 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAB Sheet 01,
View A and Fig. A-UBBAB Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer to Fig.
A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-
UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m.daN (44.25 lbf in.), refer to Fig. A-UBBAB
Sheet 01 and Fig. A-UBBAB Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAB Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 697

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAB Sheet 02, View B.

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAB Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAB Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAB Sheet 01, View
A, Fig. A-UBBAB Sheet 02, View B, Fig. A-UBBAB Sheet 03, View C and Fig.
A-UBDAB Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 698

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

(6) Subtask 521165-420-402-002 - Install the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 4.00
Minimum number of person 2
Subtask elapsed time 2.00
Skills AIRFRAME

Material necessary to do the job

Component COMPB02
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
26 MS24665-155 4 PIN
27 MS24665-300 1 PIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Polysulfide Sealant-General 06AAA1 As required
Purpose Brushable
Non Aqueous Cleaner- 08BAA9 As required
General
Wire-Locking Dia: 0.8 Mm 14QFB1 As required
Cres Nickel Alloy
Textile-Lint Free Cotton 14SBA1 As required

Standard tool TOOLB01

ITEM TOOL N˚ TOOL NAME QTY SEE
NOTES
98D32104083000 Spacer, Rigging 1 (1)

NOTE (1): If both sides are worked at the same time it is necessary to order a
second tool kit.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 699

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 32-00-00-481-001
Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Do the Job Set-Up procedure as specified in the Installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(b)

WARNING: BE CAREFUL WHEN YOU USE THE CONSUMABLE

MATERIAL(S). YOU MUST OBEY THE OPERATOR’S AND
MANUFACTURER’S HEALTH AND SAFETY INSTRUCTIONS.

Clean the component interfaces and/or adjacent areas.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

(c) Do an inspection of the component interface and/or the adjacent area.

(d) Make sure that the parts retained from the removed component are clean and are
in a serviceable condition.

(e) Prepare the MLG Fixed Fairing Assembly for installation as follows, refer to Fig. A-
UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-UBBAB
Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 700

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Remove and discard the lockwire from the nuts, Item (10).

2 Loosen the nuts, Item 9 and Item (10).

3 Adjust the eye-ends, Item (11), out of the spools, Item (12), to get dimension
V1 to between 44 mm (1.732 in.) and 46 mm and (1.811 in.), refer to Fig. A-
UBBAB Sheet 03, View D.

4 Remove, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Bolt Item (13) Retain

3 Washer Item (14) Retain

5 Loosen the nuts, Item (3), so that the studs, Item (5), can turn and make sure
that the serrated plates, Item (4), do not disengage, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

(f)

WARNING: THE WEIGHT OF THE FAIRING IS 34kg (75lb.).

Install the MLG Fixed Fairing Assembly as follows, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBBAB Sheet 02, Fig. A-UBBAB Sheet 03 and Fig. A-UBBAB Sheet 04.

1 Hold the fixed fairing assembly, Item (15), in position on the MLG.

2 Install, refer to Fig. A-UBBAB Sheet 02, View B:

1 Bush Item (16) Retained at

removal

1 Bolt Item (28) Retained at

removal

1 Washer Item (39) Retained at

removal

1 Nut Item (40) Retained at

removal

3 Install, refer to Fig. A-UBBAB Sheet 01, View A:

1 Bush Item (20) Retained at

removal

1 Bolt Item (17) Retained at

removal

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 701

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Washer Item (18) Retained at

removal

1 Nut Item (19) Retained at

removal

4 Install onto the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

5 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

6 Install, refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB Sheet 03, View C:

3 Bolt Item (21) Retained at

removal

3 Washer Item (22) Retained at

removal

3 Nut Item (23) Retained at

removal

Tighten the nuts, Item (3), sufficiently enough to make sure that the MLG fixed
fairing, Item (15), is stable during the retraction of the MLG, refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

7 Slowly retract the applicable MLG, refer to AMM Task 32-30-00-867-001.

During the retraction make sure that the fixed fairing, Item (15), does not:

- overlap the lower wing surface

- hit the hinge door

- hit the fixed underwing panel.

8 Remove, refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet
02, View B:

2 Nut Item (3) Retain

2 Locking Device Item (1) Retain

2 Plate Item (4) Retain

9 Turn the studs, Item (5), until they are fully on the rod ends, Item (6) and Item
(7).

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 702

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

10 Turn the spools, Item (12), to get the dimensions that follow, refer to Fig. A-
UBBAB Sheet 01, Fig. A-UBBAB Sheet 03, View C and Fig. A-UBCAB Sheet
01:

- dimension V between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- at position H, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- at position J, dimension T between + 0.00 mm (+ 0.000 in.) and - 4.50

mm (- 0.177 in.) (Negative Step)

- dimension S between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.)

- dimension R between 14 mm (0.551 in.) and 31 mm (1.220 in.)

- dimension P between - 2.50 mm (- 0.098 in.) (Negative Step) and 1.50

mm (0.059 in.)

- dimension Q:
Between 2.50 mm (0.098 in.) and 9.50 mm (0.374 in.) at the inboard end
of the shroud box
Between 3.20 mm (0.126 in.) and 10.20 mm (0.401 in.) at the outboard
end of the shroud box

- dimension W between 1.30 mm (0.051 in.) and 10.70 mm (0.421 in.)

- dimension x between - 3.50 mm (- 0.137 in.) (Negative Step) and 3.50

mm (0.137 in.).

11 Turn the studs, Item (5), on the rod ends, Item (6) and Item (7) until the
shoulders of the studs, Item (5), contact the support plates squarely, Item (8),
refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

12 Install:

2 Plate Item (4) Retained at

removal

2 Locking Device Item (1) Retained at

removal

2 Nut Item (3) Retained at

removal

13 Tighten the nuts, Item (3) and make sure that the serrated plates, Item (4), do
not disengage, but you can turn the studs, Item (5), refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

14 Make sure that the fixed fairing, Item (15), steps and clearances are correct as
specified at step 10. If necessary, use the spools, Item (12), to adjust the MLG
fixed fairing, Item (15), to the correct position, refer to Fig. A-UBBAB Sheet 01
and Fig. A-UBBAB Sheet 03, View C.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 703

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

15 If it is necessary, adjust each stud, Item (5), so that the stud shoulder sits
squarely on the support plate, Item (8), refer to Fig. A-UBBAB Sheet 01, View
A and Fig. A-UBBAB Sheet 02, View B.

16 Tighten the nuts, Item (3), enough, to make sure that the MLG fixed fairing,
Item (15), is stable while the MLG is being extended, refer to Fig. A-UBBAB
Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

NOTE: Do not final torque at this stage.

17 Extend the applicable MLG, refer to AMM Task 32-30-00-867-002.

18 Fit the safety devices on the applicable MLG, refer to AMM Task
32-00-00-481-001.

19 Turn the spools, Item (12), the minimum amount to align a slot with the thread
holes in the fixed fairing, Item (15), refer to Fig. A-UBBAB Sheet 01 and Fig.
A-UBBAB Sheet 03, View C.

20 Install, refer to Fig. A-UBBAB Sheet 03, View C and View F:

3 Washer Item (14) Retained at

removal

3 Bolt Item (13) Retained at

removal

21 Torque the bolts, Item (13), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.), refer to Fig. A-UBBAB Sheet 03, View F.

22

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the bolts, Item (13)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

23 Remove from the bolt, Item (17), refer to Fig. A-UBBAB Sheet 01, View A and
Fig. A-UBBAB Sheet 04, View H:

98D32104083000 Spacer, Rigging 1

24 Make sure that dimension Y and dimension Z are between 1.30 mm (0.051
in.) and 2.70 mm (0.106 in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig.
A-UBBAB Sheet 04, View G.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 704

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

25 Torque the nuts, Item (3), to between 4 m.daN (354.02 lbf in.) and 4.30 m.daN
(380.58 lbf.in.), refer to Fig. A-UBBAB Sheet 01, View A and Fig. A-UBBAB
Sheet 02, View B.

NOTE: When you tighten the nuts, Item (3), apply opposite force by
use of the flats on the studs, Item (5).

26

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (3), to the locking devices, Item (1)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

27 Apply sealant to the nuts, Item (3), locking devices, Item (1) and end of the
studs, Item (5), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet
02, View B and Fig. A-UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

28 Measure dimension X and make sure that it is not more than 44.70 mm (1.759
in.), refer to Fig. A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B
and Fig. A-UBBAB Sheet 04, View G.

NOTE: Make sure that at least 0.5 mm (0.020 in.) is visible between
rod end and stud assembly.

29 Hold the rod-ends, Item (6) and Item (7) and torque the nuts, Item 9, to
between 3.4 m.daN (300.92 lbf in.) and 3.8 m.daN (336.32 lbf in.).

30 Make sure that the rod-ends Item (6) and Item (7), are parallel to the MLG
bracket lugs.

NOTE: When you tighten the nuts, Item 9, apply opposite force by use
of the flats on the studs, Item (5).

31

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 705

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Safety the nuts, Item 9

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

32 Install the bonding strap, Item (29), on the screw, Item (30) and install the nut,
Item (31), refer to AMM Task 20-28-00-912-004 and Fig. A-UBBAB Sheet 01,
View A and Fig. A-UBBAB Sheet 02, View B.

33 Install the cover plates, Item (24), with screws, Item (25), refer to Fig. A-
UBBAB Sheet 01, View A and Fig. A-UBBAB Sheet 02, View B.

34 Torque the screws, Item (25), to between 0.17 m.daN (15.04 lbf in.) and 0.23
m.daN (20.35 lbf in.).

35 Apply sealant to the cover plates, Item (24) and screws, Item (25), refer to Fig.
A-UBBAB Sheet 01, View A, Fig. A-UBBAB Sheet 02, View B and Fig. A-
UBDAB Sheet 01.

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

36 Hold the eye-ends, Item (11) and torque the nuts, Item (10), to between 0.40
m.daN (35.40 lbf in.) and 0.50 m daN (44.25 lbf in.), refer to Fig. A-UBBAB
Sheet 01 and Fig. A-UBBAB Sheet 03, View C.

37 Measure dimension V2 and make sure that it is no more than 40 mm (1.574

in.), refer to Fig. A-UBBAB Sheet 03, View E.

38

WARNING: WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE

LOCKWIRE. CUT, REMOVE AND DISCARD THE LOCKWIRE
AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR
BLIND YOU.

Safety the nuts, Item (10)

Use:

Wire-Locking Dia: 14QFB1 As required

0.8 Mm Cres Nickel
Alloy

39 Torque the nut, Item (40), to between 1.8 m.daN (159.31 lbf in.) and 2 m.daN
(177.01 lbf in.), refer to Fig. A-UBBAB Sheet 02, View B.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 706

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

40 Torque the nut, Item (19), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01, View A.

41 Safety the nut, Item (19), refer to Fig. A-UBBAB Sheet 01, View A

With:

1 Pin-Cotter MS24665-155 Item 26

42 Safety the nut, Item (40), refer to Fig. A-UBBAB Sheet 02, View B

With:

1 Pin-Cotter MS24665-300 Item 27

43 Torque the nuts, Item (23), to between 1.15 m.daN (101.78 lbf in.) and 1.35
m.daN (119.47 lbf in.), refer to Fig. A-UBBAB Sheet 01 and Fig. A-UBBAB
Sheet 03, View C.

44 Safety the nuts, Item (23)

With:

3 Pin-Cotter MS24665-155 Item 26

45

NOTE: Make sure that sealant does not go into the spherical bearings
of the eye-ends, Item (11) and the rod-ends, Item (6) and Item
(7).

Apply sealant to the items that follow, refer to Fig. A-UBBAB Sheet 01, View
A, Fig. A-UBBAB Sheet 02, View B, Fig. A-UBBAB Sheet 03, View C and Fig.
A-UBDAB Sheet 01.

- bolts (13) and washers (14)

- bolts (21), washers (22) and nuts (23)

- nuts (10) and eye-ends (11)

- bolt (17), washer (18) and nut (19)

- bolt (28), washer (39) and nut (40)

- nuts 9, eye-ends (6) and (7) and end of studs (5).

Use:

Polysulfide Sealant- 06AAA1 As required

General Purpose
Brushable

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 707

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(7) Subtask 521165-930-401-025 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB01

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601001000 FAIRING (15) D5285601000600

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 708

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows,

refer to Fig. A-UBCAB Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBCAB Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285601000600 Item (15)

becomes:

1 Fairing Assembly D5285601001000 Item 15

6 Apply varnish to the identification plate, item 36.

Use

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 709

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Coating - Flexible 04QAB2 As required

Structure

(8) Subtask 521165-930-402-025 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.25
Skills AIRFRAME

Material necessary to do the job

Kit 521165B02R01
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

Reidentified part set REIDB01

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601001100 FAIRING (15) D5285601000700

Consumable CMLB01
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2 As required
Epoxy Adhesive-Legacy 2 05EML8 As required
Non Aqueous Cleaner- 08BAA9 As required
General
Textile-Lint Free Cotton 14SBA1 As required

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBAAB Sheet 01
Replace the LH and RH MLG Fixed
Fairing Assembly Upper and Lower
Forward Attachment Studs
Fig. A-UBBAB Sheet 01
Replace the LH and RH MLG Fixed Sheet 02
Fairing Assembly Upper and Lower Sheet 03
Forward Attachment Studs and Sheet 04
Installation of the LH and RH MLG Fixed
Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 710

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly
Fig. A-UBDAB Sheet 01
Sealing of the Upper and Lower
Attachment Studs of the LH and RH
MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02.

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, item 36, refer to Fig. A-UBBAB Sheet 01,
Fig. A-UBCAB Sheet 02 and PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285601000700 Item (15)

becomes:

1 Fairing Assembly D5285601001100 Item 15

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 711

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF ALL

D. TEST

**CONF 001

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

Manpower Resources
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

**CONF 002

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

Manpower Resources
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

**CONF 003

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

Manpower Resources
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 712

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

**CONF 004

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

Manpower Resources
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

**CONF 005

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

Manpower Resources
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

**CONF 006

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 713

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

**CONF 007

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

Manpower Resources
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

**CONF 008

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

Manpower Resources
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 714

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 009

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

Manpower Resources
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

**CONF 010

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

Manpower Resources
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

**CONF 011

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

Manpower Resources
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 715

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

**CONF 012

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

Manpower Resources
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

**CONF 013

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

Manpower Resources
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

**CONF 014

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

Manpower Resources
Skills AIRFRAME

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 716

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

**CONF 015

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

Manpower Resources
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

**CONF 016

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

Manpower Resources
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

**CONF 017

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 717

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

**CONF 018

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

Manpower Resources
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

**CONF 019

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

Manpower Resources
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 718

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 020

(1) Subtask 521165-710-401-001 - Operational Test

Work Zones and Access Panels

Zone Access/Work location
732
742

Manpower Resources
Skills AIRFRAME

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002

(a) Do the tests as specified in AMM task ’Installation of a Replacement MLG Fixed
Fairing Assembly’, refer to AMM Task 32-12-14-400-002.

**CONF ALL

E. CLOSE-UP

**CONF 001

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 719

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 002

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

**CONF 003

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 720

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 004

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

**CONF 005

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 721

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 006

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

**CONF 007

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 722

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 008

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

**CONF 009

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 723

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 010

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

**CONF 011

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 724

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 012

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

**CONF 013

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 725

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 014

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

**CONF 015

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 726

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 016

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

**CONF 017

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 727

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 018

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

**CONF 019

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 728

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 020

(1) Subtask 521165-942-401-001 - Close-Up

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) Task 32-12-14-400-002
Task 32-30-00-867-001
Task 32-30-00-867-002

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Do the Job Close-Up procedure as specified in the installation of the MLG Fixed
Fairing Assembly, refer to AMM Task 32-12-14-400-002.

(c) Do the Job Close-Up procedure as specified in the retraction of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-001.

(d) Do the Job Close-Up procedure as specified in the extension of the landing gear
after maintenance, refer to AMM Task 32-30-00-867-002.

(e) Put the aircraft back to its initial configuration.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 729

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

This Page Intentionally Left Blank

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 730

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Task 521165-831-896-001 - Modification - Additional Work 1 for Aircraft Concerned by

Configurations 001, 002, 004, 005, 007 to 015, 017 and 018 of this Revision and Modified by
Revision No. 00

**CONF ALL

WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION
BEFORE YOU START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE
FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED
DOORS - COMPONENTS THAT MOVE.

CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP

ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE). WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:

- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS

NECESSARY ON WIRING AND COMPONENTS.

- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND

OTHER CONTAMINATION.

THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION

AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.

IF THERE IS CONTAMINATION, REFER TO ESPM 20-55-00.

NOTE: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
’refer to’ are used and the operator has a procedure accepted by the local authority
he belongs to, the accepted alternative procedure can be used. When the words ’in
accordance with’ are used then the given procedure must be followed.

NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.

NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.

NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance
necessary to ensure the continued airworthiness of the aircraft.

For any deviations to the instructions contained herein, contact Airbus for further
instructions and approval.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 731

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Task Associated Data

**CONF 001

Zone
732 742
Manpower
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 002

Zone
732 742
Manpower
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 003

None

**CONF 004

Zone
732 742
Manpower
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 005

Zone
732 742
Manpower
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 006

None

**CONF 007

Zone
732 742
Manpower
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 732

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 008

Zone
732 742
Manpower
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 009

Zone
732 742
Manpower
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 010

Zone
732 742
Manpower
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 011

Zone
732 742
Manpower
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 012

Zone
732 742
Manpower
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 013

Zone
732 742
Manpower
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 733

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 014

Zone
732 742
Manpower
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 015

Zone
732 742
Manpower
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 016

None

**CONF 017

Zone
732 742
Manpower
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 018

Zone
732 742
Manpower
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 019

None

**CONF 020

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 734

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF ALL

A. GENERAL

**CONF 001

(1) Subtask 521165-910-402-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Consumable Material List (CML)

(a) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(2) Subtask 521165-839-402-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 002

(1) Subtask 521165-910-402-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Consumable Material List (CML)

(a) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(2) Subtask 521165-839-402-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 003

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 735

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 004

(1) Subtask 521165-910-402-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Consumable Material List (CML)

(a) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(2) Subtask 521165-839-402-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 005

(1) Subtask 521165-910-402-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Consumable Material List (CML)

(a) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(2) Subtask 521165-839-402-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 006

None

**CONF 007

(1) Subtask 521165-910-402-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 736

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Consumable Material List (CML)

(a) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(2) Subtask 521165-839-402-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 008

(1) Subtask 521165-910-402-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Consumable Material List (CML)

(a) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(2) Subtask 521165-839-402-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 009

(1) Subtask 521165-910-402-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Consumable Material List (CML)

(a) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(2) Subtask 521165-839-402-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 737

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 010

(1) Subtask 521165-910-402-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Consumable Material List (CML)

(a) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(2) Subtask 521165-839-402-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 011

(1) Subtask 521165-910-402-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Consumable Material List (CML)

(a) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(2) Subtask 521165-839-402-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 012

(1) Subtask 521165-910-402-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 738

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Consumable Material List (CML)

(a) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(2) Subtask 521165-839-402-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 013

(1) Subtask 521165-910-402-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Consumable Material List (CML)

(a) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(2) Subtask 521165-839-402-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 014

(1) Subtask 521165-910-402-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Consumable Material List (CML)

(a) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(2) Subtask 521165-839-402-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 739

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 015

(1) Subtask 521165-910-402-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Consumable Material List (CML)

(a) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(2) Subtask 521165-839-402-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 016

None

**CONF 017

(1) Subtask 521165-910-402-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Consumable Material List (CML)

(a) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(2) Subtask 521165-839-402-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 740

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 018

(1) Subtask 521165-910-402-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Consumable Material List (CML)

(a) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(2) Subtask 521165-839-402-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 019

None

**CONF 020

None

**CONF ALL

B. PREPARATION

**CONF 001

(1) Subtask 521165-941-402-001 - Job Set-up

Manpower Resources
Skills NON SPECIFIC

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 741

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

**CONF 002

(1) Subtask 521165-941-402-001 - Job Set-up

Manpower Resources
Skills NON SPECIFIC

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

**CONF 003

None

**CONF 004

(1) Subtask 521165-941-402-001 - Job Set-up

Manpower Resources
Skills NON SPECIFIC

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 742

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

**CONF 005

(1) Subtask 521165-941-402-001 - Job Set-up

Manpower Resources
Skills NON SPECIFIC

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

**CONF 006

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 743

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 007

(1) Subtask 521165-941-402-001 - Job Set-up

Manpower Resources
Skills NON SPECIFIC

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

**CONF 008

(1) Subtask 521165-941-402-001 - Job Set-up

Manpower Resources
Skills NON SPECIFIC

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 744

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

**CONF 009

(1) Subtask 521165-941-402-001 - Job Set-up

Manpower Resources
Skills NON SPECIFIC

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

**CONF 010

(1) Subtask 521165-941-402-001 - Job Set-up

Manpower Resources
Skills NON SPECIFIC

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 745

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

**CONF 011

(1) Subtask 521165-941-402-001 - Job Set-up

Manpower Resources
Skills NON SPECIFIC

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

**CONF 012

(1) Subtask 521165-941-402-001 - Job Set-up

Manpower Resources
Skills NON SPECIFIC

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 746

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

**CONF 013

(1) Subtask 521165-941-402-001 - Job Set-up

Manpower Resources
Skills NON SPECIFIC

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

**CONF 014

(1) Subtask 521165-941-402-001 - Job Set-up

Manpower Resources
Skills NON SPECIFIC

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 747

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

**CONF 015

(1) Subtask 521165-941-402-001 - Job Set-up

Manpower Resources
Skills NON SPECIFIC

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

**CONF 016

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 748

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 017

(1) Subtask 521165-941-402-001 - Job Set-up

Manpower Resources
Skills NON SPECIFIC

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

**CONF 018

(1) Subtask 521165-941-402-001 - Job Set-up

Manpower Resources
Skills NON SPECIFIC

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 749

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

**CONF 019

None

**CONF 020

None

**CONF ALL

C. PROCEDURE

**CONF 001

(1) Subtask 521165-831-401-001 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB02

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5284000000495 FAIRING (15) D5284000000200
(15) D5284000000400

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 750

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5284000000200 Item (15)

or

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 751

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Fairing Assembly D5284000000400 Item (15)

or

1 Fairing Assembly D5285601001000 Item (15)

becomes:

1 Fairing Assembly D5284000000495 Item 15

NOTE: Old PN D5284000000200 or D5284000000400 is the initial PN

before the embodiment of this Service Bulletin at the original
issue.

NOTE: Old PN D5285601001000 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(2) Subtask 521165-831-402-006 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB02

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5284000000595 FAIRING (15) D5284000000300

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 752

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE

NOTES
(15) D5284000000500

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 753

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5284000000300 Item (15)

or

1 Fairing Assembly D5284000000500 Item (15)

or

1 Fairing Assembly D5285601001100 Item (15)

becomes:

1 Fairing Assembly D5284000000595 Item 15

NOTE: Old PN D5284000000300 or D5284000000500 is the initial PN

before the embodiment of this Service Bulletin at the original
issue.

NOTE: Old PN D5285601001100 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 002

(1) Subtask 521165-831-401-002 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 754

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB02

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5284000000495 FAIRING (15) D5284000000200
(15) D5284000000400

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 755

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5284000000200 Item (15)

or

1 Fairing Assembly D5284000000400 Item (15)

or

1 Fairing Assembly D5285601001000 Item (15)

becomes:

1 Fairing Assembly D5284000000495 Item 15

NOTE: Old PN D5284000000200 or D5284000000400 is the initial PN

before the embodiment of this Service Bulletin at the original
issue.

NOTE: Old PN D5285601001000 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(2) Subtask 521165-831-402-007 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 756

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB02

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5284000000595 FAIRING (15) D5284000000300
(15) D5284000000500

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 757

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5284000000300 Item (15)

or

1 Fairing Assembly D5284000000500 Item (15)

or

1 Fairing Assembly D5285601001100 Item (15)

becomes:

1 Fairing Assembly D5284000000595 Item 15

NOTE: Old PN D5284000000300 or D5284000000500 is the initial PN

before the embodiment of this Service Bulletin at the original
issue.

NOTE: Old PN D5285601001100 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 003

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 758

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 004

(1) Subtask 521165-831-401-004 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB05

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5284000000695 FAIRING (15) D5284000000600

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 759

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5284000000600 Item (15)

or

1 Fairing Assembly D5285601001000 Item (15)

becomes:

1 Fairing Assembly D5284000000695 Item 15

NOTE: Old PN D5284000000600 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001000 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 760

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(2) Subtask 521165-831-402-009 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB05

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5284000000795 FAIRING (15) D5284000000700

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 761

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5284000000700 Item (15)

or

1 Fairing Assembly D5285601001100 Item (15)

becomes:

1 Fairing Assembly D5284000000795 Item 15

NOTE: Old PN D5284000000700 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001100 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 762

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 005

(1) Subtask 521165-831-401-014 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB03

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285300300095 FAIRING (15) D5285300300000

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 763

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285300300000 Item (15)

or

1 Fairing Assembly D5285601001000 Item (15)

becomes:

1 Fairing Assembly D5285300300095 Item 15

NOTE: Old PN D5285300300000 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001000 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 764

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(2) Subtask 521165-831-402-014 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB03

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285300300195 FAIRING (15) D5285300300100

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 765

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285300300100 Item (15)

or

1 Fairing Assembly D5285601001100 Item (15)

becomes:

1 Fairing Assembly D5285300300195 Item 15

NOTE: Old PN D5285300300100 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001100 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 766

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 006

None

**CONF 007

(1) Subtask 521165-831-401-007 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB06

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000295 FAIRING (15) D5285600000200
(15) D5285601000000

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 767

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAC Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAC Sheet 03

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285600000200 Item (15)

or

1 Fairing Assembly D5285601000000 Item (15)

or

1 Fairing Assembly D5285601001000 Item (15)

becomes:

1 Fairing Assembly D5285600000295 Item 15

NOTE: Old PN D5285600000200 or D5285601000000 is the initial PN

before the embodiment of this Service Bulletin at the original
issue.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 768

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

NOTE: Old PN D5285601001000 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(2) Subtask 521165-831-402-012 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB06

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000395 FAIRING (15) D5285600000300
(15) D5285601000100

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 769

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAC Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAC Sheet 03

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285600000300 Item (15)

or

1 Fairing Assembly D5285601000100 Item (15)

or

1 Fairing Assembly D5285601001100 Item (15)

becomes:

1 Fairing Assembly D5285600000395 Item 15

NOTE: Old PN D5285600000300 or D5285601000100 is the initial PN

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 770

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

before the embodiment of this Service Bulletin at the original

issue.

NOTE: Old PN D5285601001100 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 008

(1) Subtask 521165-831-401-015 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB03

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285300300095 FAIRING (15) D5285300300000

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 771

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE

CML MAT. No. NOTES
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285300300000 Item (15)

or

1 Fairing Assembly D5285601001000 Item (15)

becomes:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 772

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Fairing Assembly D5285300300095 Item 15

NOTE: Old PN D5285300300000 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001000 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(2) Subtask 521165-831-402-015 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB03

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285300300195 FAIRING (15) D5285300300100

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 773

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE

CML MAT. No. NOTES
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285300300100 Item (15)

or

1 Fairing Assembly D5285601001100 Item (15)

becomes:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 774

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Fairing Assembly D5285300300195 Item 15

NOTE: Old PN D5285300300100 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001100 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 009

(1) Subtask 521165-831-401-010 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB07

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601000295 FAIRING (15) D5285601000200

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 775

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE

CML MAT. No. NOTES
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAD Sheet 03

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285601000200 Item (15)

or

1 Fairing Assembly D5285601001000 Item (15)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 776

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

becomes:

1 Fairing Assembly D5285601000295 Item 15

NOTE: Old PN D5285601000200 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001000 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(2) Subtask 521165-831-402-002 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB07

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601000395 FAIRING (15) D5285601000300

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 777

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE

CML MAT. No. NOTES
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAD Sheet 03

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285601000300 Item (15)

or

1 Fairing Assembly D5285601001100 Item (15)

becomes:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 778

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Fairing Assembly D5285601000395 Item 15

NOTE: Old PN D5285601000300 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001100 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 010

(1) Subtask 521165-831-401-012 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB08

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601000495 FAIRING (15) D5285601000400

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 779

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE

CML MAT. No. NOTES
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAD Sheet 03

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285601000400 Item (15)

or

1 Fairing Assembly D5285601001000 Item (15)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 780

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

becomes:

1 Fairing Assembly D5285601000495 Item 15

NOTE: Old PN D5285601000400 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001000 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(2) Subtask 521165-831-402-004 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB08

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601000595 FAIRING (15) D5285601000500

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 781

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE

CML MAT. No. NOTES
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAD Sheet 03

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285601000500 Item (15)

or

1 Fairing Assembly D5285601001100 Item (15)

becomes:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 782

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Fairing Assembly D5285601000595 Item 15

NOTE: Old PN D5285601000500 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001100 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 011

(1) Subtask 521165-831-401-016 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB06

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000295 FAIRING (15) D5285600000200
(15) D5285601000000

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 783

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAD Sheet 03

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285600000200 Item (15)

or

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 784

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Fairing Assembly D5285601000000 Item (15)

or

1 Fairing Assembly D5285601001000 Item (15)

becomes:

1 Fairing Assembly D5285600000295 Item 15

NOTE: Old PN D5285600000200 or D5285601000000 is the initial PN

before the embodiment of this Service Bulletin at the original
issue.

NOTE: Old PN D5285601001000 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(2) Subtask 521165-831-402-016 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB06

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000395 FAIRING (15) D5285600000300

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 785

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE

NOTES
(15) D5285601000100

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAD Sheet 03

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 786

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285600000300 Item (15)

or

1 Fairing Assembly D5285601000100 Item (15)

or

1 Fairing Assembly D5285601001100 Item (15)

becomes:

1 Fairing Assembly D5285600000395 Item 15

NOTE: Old PN D5285600000300 or D5285601000100 is the initial PN

before the embodiment of this Service Bulletin at the original
issue.

NOTE: Old PN D5285601001100 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 012

(1) Subtask 521165-831-401-017 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 787

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB05

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5284000000695 FAIRING (15) D5284000000600

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 788

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5284000000600 Item (15)

or

1 Fairing Assembly D5285601001000 Item (15)

becomes:

1 Fairing Assembly D5284000000695 Item 15

NOTE: Old PN D5284000000600 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001000 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(2) Subtask 521165-831-402-017 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 789

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Reidentified part set REIDB05

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5284000000795 FAIRING (15) D5284000000700

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 790

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5284000000700 Item (15)

or

1 Fairing Assembly D5285601001100 Item (15)

becomes:

1 Fairing Assembly D5284000000795 Item 15

NOTE: Old PN D5284000000700 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001100 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 013

(1) Subtask 521165-831-401-018 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 791

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Reidentified part set REIDB08

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601000495 FAIRING (15) D5285601000400

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 792

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285601000400 Item (15)

or

1 Fairing Assembly D5285601001000 Item (15)

becomes:

1 Fairing Assembly D5285601000495 Item 15

NOTE: Old PN D5285601000400 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001000 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(2) Subtask 521165-831-402-018 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 793

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Reidentified part set REIDB08

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601000595 FAIRING (15) D5285601000500

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 794

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285601000500 Item (15)

or

1 Fairing Assembly D5285601001100 Item (15)

becomes:

1 Fairing Assembly D5285601000595 Item 15

NOTE: Old PN D5285601000500 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001100 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 014

(1) Subtask 521165-831-401-019 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 795

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Reidentified part set REIDB09

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000095 FAIRING (15) D5285600000000

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 796

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285600000000 Item (15)

or

1 Fairing Assembly D5285601001000 Item (15)

becomes:

1 Fairing Assembly D5285600000095 Item 15

NOTE: Old PN D5285600000000 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001000 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(2) Subtask 521165-831-402-019 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 797

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Reidentified part set REIDB09

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000195 FAIRING (15) D5285600000100

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 798

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing assembly D5285600000100 Item (15)

or

1 Fairing Assembly D5285601001100 Item (15)

becomes:

1 Fairing Assembly D5285600000195 Item 15

NOTE: Old PN D5285600000100 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001100 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 015

(1) Subtask 521165-831-401-020 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 799

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Reidentified part set REIDB10

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000295 FAIRING (15) D5285600000200

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 800

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285600000200 Item (15)

or

1 Fairing Assembly D5285601001000 Item (15)

becomes:

1 Fairing Assembly D5285600000295 Item 15

NOTE: Old PN D5285600000200 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001000 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(2) Subtask 521165-831-402-020 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 801

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Reidentified part set REIDB10

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000395 FAIRING (15) D5285600000300

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAA Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAA Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 802

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285600000300 Item (15)

or

1 Fairing Assembly D5285601001100 Item (15)

becomes:

1 Fairing Assembly D5285600000395 Item 15

NOTE: Old PN D5285600000300 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001100 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 016

None

**CONF 017

(1) Subtask 521165-831-401-022 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 803

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB06

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000295 FAIRING (15) D5285600000200
(15) D5285601000000

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 804

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285600000200 Item (15)

or

1 Fairing Assembly D5285601000000 Item (15)

or

1 Fairing Assembly D5285601001000 Item (15)

becomes:

1 Fairing Assembly D5285600000295 Item 15

NOTE: Old PN D5285600000200 or D5285601000000 is the initial PN

before the embodiment of this Service Bulletin at the original
issue.

NOTE: Old PN D5285601001000 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(2) Subtask 521165-831-402-022 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 805

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB06

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000395 FAIRING (15) D5285600000300
(15) D5285601000100

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 806

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285600000300 Item (15)

or

1 Fairing Assembly D5285601000100 Item (15)

or

1 Fairing Assembly D5285601001100 Item (15)

becomes:

1 Fairing Assembly D5285600000395 Item 15

NOTE: Old PN D5285600000300 or D5285601000100 is the initial PN

before the embodiment of this Service Bulletin at the original
issue.

NOTE: Old PN D5285601001100 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 018

(1) Subtask 521165-831-401-023 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 807

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB07

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601000295 FAIRING (15) D5285601000200

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 808

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285601000200 Item (15)

or

1 Fairing Assembly D5285601001000 Item (15)

becomes:

1 Fairing Assembly D5285601000295 Item 15

NOTE: Old PN D5285601000200 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001000 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(2) Subtask 521165-831-402-023 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 809

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB07

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285601000395 FAIRING (15) D5285601000300

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 810

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing Assembly D5285601000300 Item (15)

or

1 Fairing Assembly D5285601001100 Item (15)

becomes:

1 Fairing Assembly D5285601000395 Item 15

NOTE: Old PN D5285601000300 is the initial PN before the

embodiment of this Service Bulletin at the original issue.

NOTE: Old PN D5285601001100 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 019

None

**CONF 020

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 811

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF ALL

D. TEST

**CONF 001

None

**CONF 002

None

**CONF 003

None

**CONF 004

None

**CONF 005

None

**CONF 006

None

**CONF 007

None

**CONF 008

None

**CONF 009

None

**CONF 010

None

**CONF 011

None

**CONF 012

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 812

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 013

None

**CONF 014

None

**CONF 015

None

**CONF 016

None

**CONF 017

None

**CONF 018

None

**CONF 019

None

**CONF 020

None

**CONF ALL

E. CLOSE-UP

**CONF 001

(1) Subtask 521165-942-402-001 - Close-up

Manpower Resources
Skills NON SPECIFIC

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Put the aircraft back to its initial configuration.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 813

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 002

(1) Subtask 521165-942-402-001 - Close-up

Manpower Resources
Skills NON SPECIFIC

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Put the aircraft back to its initial configuration.

**CONF 003

None

**CONF 004

(1) Subtask 521165-942-402-001 - Close-up

Manpower Resources
Skills NON SPECIFIC

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Put the aircraft back to its initial configuration.

**CONF 005

(1) Subtask 521165-942-402-001 - Close-up

Manpower Resources
Skills NON SPECIFIC

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Put the aircraft back to its initial configuration.

**CONF 006

None

**CONF 007

(1) Subtask 521165-942-402-001 - Close-up

Manpower Resources
Skills NON SPECIFIC

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 814

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(b) Put the aircraft back to its initial configuration.

**CONF 008

(1) Subtask 521165-942-402-001 - Close-up

Manpower Resources
Skills NON SPECIFIC

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Put the aircraft back to its initial configuration.

**CONF 009

(1) Subtask 521165-942-402-001 - Close-up

Manpower Resources
Skills NON SPECIFIC

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Put the aircraft back to its initial configuration.

**CONF 010

(1) Subtask 521165-942-402-001 - Close-up

Manpower Resources
Skills NON SPECIFIC

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Put the aircraft back to its initial configuration.

**CONF 011

(1) Subtask 521165-942-402-001 - Close-up

Manpower Resources
Skills NON SPECIFIC

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Put the aircraft back to its initial configuration.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 815

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 012

(1) Subtask 521165-942-402-001 - Close-up

Manpower Resources
Skills NON SPECIFIC

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Put the aircraft back to its initial configuration.

**CONF 013

(1) Subtask 521165-942-402-001 - Close-up

Manpower Resources
Skills NON SPECIFIC

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Put the aircraft back to its initial configuration.

**CONF 014

(1) Subtask 521165-942-402-001 - Close-up

Manpower Resources
Skills NON SPECIFIC

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Put the aircraft back to its initial configuration.

**CONF 015

(1) Subtask 521165-942-402-001 - Close-up

Manpower Resources
Skills NON SPECIFIC

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Put the aircraft back to its initial configuration.

**CONF 016

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 816

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 017

(1) Subtask 521165-942-402-001 - Close-up

Manpower Resources
Skills NON SPECIFIC

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Put the aircraft back to its initial configuration.

**CONF 018

(1) Subtask 521165-942-402-001 - Close-up

Manpower Resources
Skills NON SPECIFIC

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Put the aircraft back to its initial configuration.

**CONF 019

None

**CONF 020

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 817

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

This Page Intentionally Left Blank

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 818

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Task 521165-831-897-001 - Modification - Additional Work 2 for Aircraft Concerned by

Configuration 016 of this Revision and Modified by the Original Issue or Revision No. 01, or
Reidentified by the Additional Work from Revision No. 01

**CONF ALL

WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION
BEFORE YOU START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE
FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED
DOORS - COMPONENTS THAT MOVE.

CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP

ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE). WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:

- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS

NECESSARY ON WIRING AND COMPONENTS.

- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND

OTHER CONTAMINATION.

THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION

AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.

IF THERE IS CONTAMINATION, REFER TO ESPM 20-55-00.

NOTE: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
’refer to’ are used and the operator has a procedure accepted by the local authority
he belongs to, the accepted alternative procedure can be used. When the words ’in
accordance with’ are used then the given procedure must be followed.

NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.

NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.

NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance
necessary to ensure the continued airworthiness of the aircraft.

For any deviations to the instructions contained herein, contact Airbus for further
instructions and approval.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 819

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Task Associated Data

**CONF 001

None

**CONF 002

None

**CONF 003

None

**CONF 004

None

**CONF 005

None

**CONF 006

None

**CONF 007

None

**CONF 008

None

**CONF 009

None

**CONF 010

None

**CONF 011

None

**CONF 012

None

**CONF 013

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 820

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 014

None

**CONF 015

None

**CONF 016

Zone
732 742
Manpower
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 017

None

**CONF 018

None

**CONF 019

None

**CONF 020

None

**CONF ALL

A. GENERAL

**CONF 001

None

**CONF 002

None

**CONF 003

None

**CONF 004

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 821

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 005

None

**CONF 006

None

**CONF 007

None

**CONF 008

None

**CONF 009

None

**CONF 010

None

**CONF 011

None

**CONF 012

None

**CONF 013

None

**CONF 014

None

**CONF 015

None

**CONF 016

(1) Subtask 521165-910-403-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 822

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
11-00-00, Page Block 201
Consumable Material List (CML)
Structural Repair Manual (SRM) 51-24-00

(a) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(b) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(c) Apply sealant in accordance with SRM 51-24-00.

(d) For the installation of placards, refer to AMM 11-00-00, Page Block 201.

(2) Subtask 521165-839-403-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 017

None

**CONF 018

None

**CONF 019

None

**CONF 020

None

**CONF ALL

B. PREPARATION

**CONF 001

None

**CONF 002

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 823

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 003

None

**CONF 004

None

**CONF 005

None

**CONF 006

None

**CONF 007

None

**CONF 008

None

**CONF 009

None

**CONF 010

None

**CONF 011

None

**CONF 012

None

**CONF 013

None

**CONF 014

None

**CONF 015

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 824

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 016

(1) Subtask 521165-941-403-001 - Job Set-up

Manpower Resources
Skills NON SPECIFIC

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

**CONF 017

None

**CONF 018

None

**CONF 019

None

**CONF 020

None

**CONF ALL

C. PROCEDURE

**CONF 001

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 825

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 002

None

**CONF 003

None

**CONF 004

None

**CONF 005

None

**CONF 006

None

**CONF 007

None

**CONF 008

None

**CONF 009

None

**CONF 010

None

**CONF 011

None

**CONF 012

None

**CONF 013

None

**CONF 014

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 826

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 015

None

**CONF 016

(1) Subtask 521165-930-403-003 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB04

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000095 FAIRING (15) D5285600000000
15 D5285875100095 FAIRING (15) D5285875100000

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Aircraft Maintenance Manual (AMM) 11-00-00, Page Block 201

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 827

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing, refer to AMM 11-00-00, Page Block 201:

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285600000000 Item (15)

or

1 Fairing Assembly D5285601001000 Item (15)

becomes:

1 Fairing Assembly D5285600000095 Item 15

or

1 Fairing Assembly D5285875100000 Item (15)

becomes:

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 828

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Fairing Assembly D5285875100095 Item 15

NOTE: Old PN D5285600000000 or D5285875100000 are the initial

PN before the embodiment of this Service Bulletin at the
original issue or at Revision No. 01.

NOTE: Old PN D5285601001000 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(2) Subtask 521165-930-406-001 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB04

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000195 FAIRING (15) D5285600000100
15 D5285875100195 FAIRING (15) D5285875100100

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 829

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE

CML MAT. No. NOTES
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Aircraft Maintenance Manual (AMM) 11-00-00, Page Block 201
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAB Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAB Sheet 02

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing, refer to AMM 11-00-00, Page Block 201:

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing assembly D5285600000100 Item (15)

or

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 830

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

1 Fairing Assembly D5285601001100 Item (15)

becomes:

1 Fairing Assembly D5285600000195 Item 15

or

1 Fairing Assembly D5285875100100 Item (15)

becomes:

1 Fairing Assembly D5285875100195 Item 15

NOTE: Old PN D5285600000100 or D5285875100100 are the initial

PN before the embodiment of this Service Bulletin at the
original issue or at Revision No. 01.

NOTE: Old PN D5285601001100 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 017

None

**CONF 018

None

**CONF 019

None

**CONF 020

None

**CONF ALL

D. TEST

**CONF 001

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 831

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 002

None

**CONF 003

None

**CONF 004

None

**CONF 005

None

**CONF 006

None

**CONF 007

None

**CONF 008

None

**CONF 009

None

**CONF 010

None

**CONF 011

None

**CONF 012

None

**CONF 013

None

**CONF 014

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 832

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 015

None

**CONF 016

None

**CONF 017

None

**CONF 018

None

**CONF 019

None

**CONF 020

None

**CONF ALL

E. CLOSE-UP

**CONF 001

None

**CONF 002

None

**CONF 003

None

**CONF 004

None

**CONF 005

None

**CONF 006

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 833

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 007

None

**CONF 008

None

**CONF 009

None

**CONF 010

None

**CONF 011

None

**CONF 012

None

**CONF 013

None

**CONF 014

None

**CONF 015

None

**CONF 016

(1) Subtask 521165-942-403-001 - Close-up

Manpower Resources
Skills NON SPECIFIC

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Put the aircraft back to its initial configuration.

**CONF 017

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 834

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 018

None

**CONF 019

None

**CONF 020

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 835

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

This Page Intentionally Left Blank

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 836

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Task 521165-831-898-001 - Modification - Additional Work 3 for Aircraft Concerned by

Configurations 003 and 006 of this Revision and Modified by Revision No. 02 or any
Previous Issue, or Reidentified by the Additional Work from Revision No. 01 or Revision No.
02

**CONF ALL

WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION
BEFORE YOU START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE
FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED
DOORS - COMPONENTS THAT MOVE.

CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP

ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE). WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:

- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS

NECESSARY ON WIRING AND COMPONENTS.

- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND

OTHER CONTAMINATION.

THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION

AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.

IF THERE IS CONTAMINATION, REFER TO ESPM 20-55-00.

NOTE: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
’refer to’ are used and the operator has a procedure accepted by the local authority
he belongs to, the accepted alternative procedure can be used. When the words ’in
accordance with’ are used then the given procedure must be followed.

NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.

NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.

NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance
necessary to ensure the continued airworthiness of the aircraft.

For any deviations to the instructions contained herein, contact Airbus for further
instructions and approval.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 837

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Task Associated Data

**CONF 001

None

**CONF 002

None

**CONF 003

Zone
732 742
Manpower
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 004

None

**CONF 005

None

**CONF 006

Zone
732 742
Manpower
TOTAL MANHOURS 1.50
ELAPSED TIME (HOURS) 0.75

**CONF 007

None

**CONF 008

None

**CONF 009

None

**CONF 010

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 838

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 011

None

**CONF 012

None

**CONF 013

None

**CONF 014

None

**CONF 015

None

**CONF 016

None

**CONF 017

None

**CONF 018

None

**CONF 019

None

**CONF 020

None

**CONF ALL

A. GENERAL

**CONF 001

None

**CONF 002

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 839

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 003

(1) Subtask 521165-910-404-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
11-00-00, Page Block 201
Consumable Material List (CML)
Structural Repair Manual (SRM) 51-24-00

(a) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

(b) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(c) Apply sealant in accordance with SRM 51-24-00.

(d) For the installation of placards, refer to AMM 11-00-00, Page Block 201.

(2) Subtask 521165-839-404-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 004

None

**CONF 005

None

**CONF 006

(1) Subtask 521165-910-404-001 - Standard Practices

Manpower Resources
Skills NON SPECIFIC

References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
11-00-00, Page Block 201
Consumable Material List (CML)
Structural Repair Manual (SRM) 51-24-00

(a) For the identification of zones, refer to AMM 06-20-00, Page Block 001.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 840

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(b) For the specification of materials (Mat. No.) given in this Service Bulletin, refer to
Consumable Materials List (CML).

(c) Apply sealant in accordance with SRM 51-24-00.

(d) For the installation of placards, refer to AMM 11-00-00, Page Block 201.

(2) Subtask 521165-839-404-001 - Administrative

Manpower Resources
Skills NON SPECIFIC

Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.

**CONF 007

None

**CONF 008

None

**CONF 009

None

**CONF 010

None

**CONF 011

None

**CONF 012

None

**CONF 013

None

**CONF 014

None

**CONF 015

None

**CONF 016

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 841

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 017

None

**CONF 018

None

**CONF 019

None

**CONF 020

None

**CONF ALL

B. PREPARATION

**CONF 001

None

**CONF 002

None

**CONF 003

(1) Subtask 521165-941-404-001 - Job Set-up

Manpower Resources
Skills NON SPECIFIC

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 842

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

- All controls in NORM, AUTO or OFF position.

**CONF 004

None

**CONF 005

None

**CONF 006

(1) Subtask 521165-941-404-001 - Job Set-up

Manpower Resources
Skills NON SPECIFIC

NOTE: The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:

- Aircraft on the ground resting on landing gear (the ground safety

locks and the wheel chocks are in position on the landing gear)

- Engine shut down, thrust reversers closed and locked

- Aircraft in clean configuration

- Parking brake applied

- Aircraft electrical network de-energized

- Hydraulic systems depressurized

- Access to the cockpit and cabin is available

- All circuit breakers are in closed position

- All controls in NORM, AUTO or OFF position.

**CONF 007

None

**CONF 008

None

**CONF 009

None

**CONF 010

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 843

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 011

None

**CONF 012

None

**CONF 013

None

**CONF 014

None

**CONF 015

None

**CONF 016

None

**CONF 017

None

**CONF 018

None

**CONF 019

None

**CONF 020

None

**CONF ALL

C. PROCEDURE

**CONF 001

None

**CONF 002

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 844

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 003

(1) Subtask 521165-930-405-001 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB04

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000095 FAIRING (15) D5285600000000
15 D5285875100095 FAIRING (15) D5285875100000

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Aircraft Maintenance Manual (AMM) 11-00-00, Page Block 201
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 845

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

References
Fig. A-UBCAC Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAC Sheet 03

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing, refer to AMM 11-00-00, Page Block 201:

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285600000000 Item (15)

or

1 Fairing Assembly D5285601001000 Item (15)

becomes:

1 Fairing Assembly D5285600000095 Item 15

or

1 Fairing Assembly D5285875100000 Item (15)

becomes:

1 Fairing Assembly D5285875100095 Item 15

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 846

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

NOTE: Old PN D5285600000000 or D5285875100000 are the initial

PN before the embodiment of this Service Bulletin at the
original issue or at Revision No. 01.

NOTE: Old PN D5285601001000 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(2) Subtask 521165-930-407-001 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB04

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000195 FAIRING (15) D5285600000100
15 D5285875100195 FAIRING (15) D5285875100100

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 847

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE

CML MAT. No. NOTES
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Aircraft Maintenance Manual (AMM) 11-00-00, Page Block 201
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAC Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAC Sheet 03

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing, refer to AMM 11-00-00, Page Block 201:

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing assembly D5285600000100 Item (15)

or

1 Fairing Assembly D5285601001100 Item (15)

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 848

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

becomes:

1 Fairing Assembly D5285600000195 Item 15

or

1 Fairing Assembly D5285875100100 Item (15)

becomes:

1 Fairing Assembly D5285875100195 Item 15

NOTE: Old PN D5285600000100 or D5285875100100 are the initial

PN before the embodiment of this Service Bulletin at the
original issue or at Revision No. 01.

NOTE: Old PN D5285601001100 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

**CONF 004

None

**CONF 005

None

**CONF 006

(1) Subtask 521165-930-405-002 - Reidentify the LH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
732

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 849

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB04

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000095 FAIRING (15) D5285600000000
15 D5285875100095 FAIRING (15) D5285875100000

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Aircraft Maintenance Manual (AMM) 11-00-00, Page Block 201
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03

(a) Reidentify the LH MLG Fairing as follows, refer to Fig. A-UBCAD Sheet 03

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 850

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing, refer to AMM 11-00-00, Page Block 201:

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the LH MLG Fairing:

1 Fairing Assembly D5285600000000 Item (15)

or

1 Fairing Assembly D5285601001000 Item (15)

becomes:

1 Fairing Assembly D5285600000095 Item 15

or

1 Fairing Assembly D5285875100000 Item (15)

becomes:

1 Fairing Assembly D5285875100095 Item 15

NOTE: Old PN D5285600000000 or D5285875100000 are the initial

PN before the embodiment of this Service Bulletin at the
original issue or at Revision No. 01.

NOTE: Old PN D5285601001000 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

Coating - Flexible 04QAB2 As required

Structure

(2) Subtask 521165-930-407-002 - Reidentify the RH MLG Fixed Fairing Assembly

Work Zones and Access Panels

Zone Access/Work location
742

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 851

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC

Material necessary to do the job

Kit 521165B03R00
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
36 NSA9117-20 1 PLATE

NOTE: Kit 521165B03R00 is applicable for the Additional Works 1, 2 and 3.

NOTE: The above list of components is not an AIRBUS Kit, the required parts
shall be ordered as necessary through the given channel.

Reidentified part set REIDB04

ITEM NEW PART N˚ KEYWORD ITEM OLD PART N˚ SEE
NOTES
15 D5285600000195 FAIRING (15) D5285600000100
15 D5285875100195 FAIRING (15) D5285875100100

Consumable CMLB02
ITEM DESCRIPTION REFERENCE TO QTY PER A/C SEE
CML MAT. No. NOTES
Coating - Flexible Structure 04QAB2
Epoxy Adhesive-Legacy 2 05EML8
Non Aqueous Cleaner- 08BAA9
General
Textile-Lint Free Cotton 14SBA1

NOTE: Consumable CMLB02 is applicable for the Additional Works 1, 2 and 3.

References
Aircraft Maintenance Manual (AMM) 11-00-00, Page Block 201
Process and Material Specification Process and Material Specification (PMS)
(PMS) 01-06-13
Fig. A-UBCAD Sheet 01
Installation Dimensions of the LH and Sheet 02
RH MLG Fixed Fairing Assembly Sheet 03

(a) Reidentify the RH MLG Fairing as follows, refer to Fig. A-UBCAD Sheet 03

1 Carefully remove

1 Plate-Identification NSA9117-20 Item (36) Discard

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 852

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

2 Clean the area where the plate was removed.

Use:

Textile-Lint Free 14SBA1 As required

Cotton

made moist with

Non Aqueous 08BAA9 As required

Cleaner-General

3 Bond to the fairing, refer to AMM 11-00-00, Page Block 201:

1 Plate-Identification NSA9117-20 Item 36

Use:

Epoxy Adhesive- 05EML8 As required

Legacy 2

4 Mark the new Part No. and transfer any relevant information from the old plate
on to the new identification plate, Item 36, refer to PMS 01-06-13.

5 After modification, the Part No. of the RH MLG Fairing:

1 Fairing assembly D5285600000100 Item (15)

or

1 Fairing Assembly D5285601001100 Item (15)

becomes:

1 Fairing Assembly D5285600000195 Item 15

or

1 Fairing Assembly D5285875100100 Item (15)

becomes:

1 Fairing Assembly D5285875100195 Item 15

NOTE: Old PN D5285600000100 or D5285875100100 are the initial

PN before the embodiment of this Service Bulletin at the
original issue or at Revision No. 01.

NOTE: Old PN D5285601001100 is the reidentified PN after the

embodiment of this Service Bulletin at the original issue.

6 Apply varnish to the identification plate, item 36.

Use

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 853

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

Coating - Flexible 04QAB2 As required

Structure

**CONF 007

None

**CONF 008

None

**CONF 009

None

**CONF 010

None

**CONF 011

None

**CONF 012

None

**CONF 013

None

**CONF 014

None

**CONF 015

None

**CONF 016

None

**CONF 017

None

**CONF 018

None

**CONF 019

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 854

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 020

None

**CONF ALL

D. TEST

**CONF 001

None

**CONF 002

None

**CONF 003

None

**CONF 004

None

**CONF 005

None

**CONF 006

None

**CONF 007

None

**CONF 008

None

**CONF 009

None

**CONF 010

None

**CONF 011

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 855

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 012

None

**CONF 013

None

**CONF 014

None

**CONF 015

None

**CONF 016

None

**CONF 017

None

**CONF 018

None

**CONF 019

None

**CONF 020

None

**CONF ALL

E. CLOSE-UP

**CONF 001

None

**CONF 002

None

**CONF 003

(1) Subtask 521165-942-404-001 - Close-up

Manpower Resources
Skills NON SPECIFIC

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 856

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Put the aircraft back to its initial configuration.

**CONF 004

None

**CONF 005

None

**CONF 006

(1) Subtask 521165-942-404-001 - Close-up

Manpower Resources
Skills NON SPECIFIC

(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.

(b) Put the aircraft back to its initial configuration.

**CONF 007

None

**CONF 008

None

**CONF 009

None

**CONF 010

None

**CONF 011

None

**CONF 012

None

**CONF 013

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 857

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 014

None

**CONF 015

None

**CONF 016

None

**CONF 017

None

**CONF 018

None

**CONF 019

None

**CONF 020

None

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 858

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 001, 004 thru 005, 014 thru 015

MLG
FIXED
FAIRING
ASSEMBLY

A BEFORE

LH SHOWN
RH SIMILAR
(2)
(8) (1)

(3) (3)

A (6) (4)
B (7)

(5)
BRACKET
LUGS

A B

N_SB_521165_7_BAAA_01_02

Figure A-UBAAA - Sheet 01

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 859

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 002, 008, 012 thru 013, 016 thru 018, 020

MLG
FIXED
FAIRING
ASSEMBLY

A
BEFORE
LH SHOWN
RH SIMILAR

(2)
(1)

(9)
(3)
(4)
A (6)
B (7)

(5)
BRACKET (8)
LUGS

A B

N_SB_521165_7_BAAB_01_03

Figure A-UBAAB - Sheet 01

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 860

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 003, 007

MLG
FIXED
FAIRING
ASSEMBLY

A BEFORE

LH SHOWN
RH SIMILAR
(2)
(8) (1)

(3) (3)

A (6) (4)
B (7)

(5)
BRACKET
LUGS

A B

N_SB_521165_7_BAAC_01_01

Figure A-UBAAC - Sheet 01

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 861

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 006, 009 thru 011, 019

MLG
FIXED
FAIRING
ASSEMBLY

A
BEFORE
LH SHOWN
RH SIMILAR

(2)
(1)

(9)
(3)
(4)
A (6)
B (7)

(5)
BRACKET (8)
LUGS

A B

N_SB_521165_7_BAAD_01_01

Figure A-UBAAD - Sheet 01

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 862

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 001, 004 thru 005, 014 thru 015

MLG

(15)

C AFTER
C (24) (25)

3
A
5
1
LH SHOWN
RH SIMILAR
(17)

01 (4)
(20)
(30)

6
9

(18) 8
26 (31)
(19) G H (29)

A
NOTE:
ELECTRICAL BONDING
01 APPLY GREASE (MAT. NO. 03GBC1) TO THREADS
BEFORE ASSEMBLY INTO STUD ADJUSTER N_SB_521165_7_BBAA_01_05

Figure A-UBBAA - Sheet 01

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs and
Installation of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 863

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 001, 004 thru 005, 014 thru 015

AFTER
(24) (25)

3
5
1

(28)
01 (4)

(30)

7
9
8
(31)
(16) G (29)

(39)
(40) 27
B

NOTE:
ELECTRICAL BONDING
01 APPLY GREASE (MAT. NO. 03GBC1) TO THREADS
BEFORE ASSEMBLY INTO STUD ADJUSTER N_SB_521165_7_BBAA_02_04

Figure A-UBBAA - Sheet 02

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs and
Installation of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 864

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 001, 004 thru 005, 014 thru 015

D E
(12)
(21)

(10)

DIM ’V1’
(11)
(22)

(23)
(14)
(13)
26 F

C D
TYPICAL
TYPICAL

SPOOL LOCK SCREW

LOCK SCREW POSITION

DIM ’V2’

E F
TYPICAL TYPICAL

N_SB_521165_7_BBAA_03_03

Figure A-UBBAA - Sheet 03

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs and
Installation of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 865

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 001, 004 thru 005, 014 thru 015

DIM ’Y’ 02
02 DIM ’Z’

DIM ’X’

G
VIEW LOOKING UP

(17)

RIGGING
SPACERS

H
VIEW LOOKING UP

NOTE:
02 USED AT POSITION A ONLY N_SB_521165_7_BBAA_04_01

Figure A-UBBAA - Sheet 04

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs and
Installation of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 866

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 002, 008, 012 thru 013, 016 thru 018, 020

MLG

(15)

C AFTER
C (24) (25)

3
A
5
1
LH SHOWN
RH SIMILAR
(17)

01 (4)
(20)
(30)

6
9

(18) 8
26 (31)
(19) G H (29)

A
NOTE:
ELECTRICAL BONDING
01 APPLY GREASE (MAT. NO. 03GBC1) TO THREADS
BEFORE ASSEMBLY INTO STUD ADJUSTER N_SB_521165_7_BBAB_01_05

Figure A-UBBAB - Sheet 01

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs and
Installation of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 867

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 002, 008, 012 thru 013, 016 thru 018, 020

AFTER
(24) (25)

3
5
1

(28)
01 (4)

(30)

7
9
8
(31)
(16) G (29)

(39)
(40) 27
B

NOTE:
ELECTRICAL BONDING
01 APPLY GREASE (MAT. NO. 03GBC1) TO THREADS
BEFORE ASSEMBLY INTO STUD ADJUSTER N_SB_521165_7_BBAB_02_04

Figure A-UBBAB - Sheet 02

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs and
Installation of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 868

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 002, 008, 012 thru 013, 016 thru 018, 020

D E
(12)
(21)

(10)

DIM ’V1’
(11)
(22)

(23)
(14)
(13)
26 F

C D
TYPICAL
TYPICAL

SPOOL LOCK SCREW

LOCK SCREW POSITION

DIM ’V2’

E F
TYPICAL TYPICAL

N_SB_521165_7_BBAB_03_03

Figure A-UBBAB - Sheet 03

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs and
Installation of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 869

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 002, 008, 012 thru 013, 016 thru 018, 020

DIM ’Y’ 02
02 DIM ’Z’

DIM ’X’

G
VIEW LOOKING UP

(17)

RIGGING
SPACERS

H
VIEW LOOKING UP

NOTE:
02 USED AT POSITION A ONLY N_SB_521165_7_BBAB_04_01

Figure A-UBBAB - Sheet 04

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs and
Installation of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 870

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 003, 007

MLG

(15)

B (32)

C AFTER
C (24) (25)

3
A
5
1
LH SHOWN
RH SIMILAR
(17)

01 (4)
(20)
(30)

6
9

(18) 8
26 (31)
(19) G H (29)

A
NOTE:
ELECTRICAL BONDING
01 APPLY GREASE (MAT. NO. 03GBC1) TO THREADS
BEFORE ASSEMBLY INTO STUD ADJUSTER N_SB_521165_7_BBAC_01_04

Figure A-UBBAC - Sheet 01

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs and
Installation of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 871

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 003, 007

AFTER
(24) (25)

3
5
1

(28)
01 (4)

(30)

7
9
8
(31)
(16) G (29)

(39)
(40) 27
B

NOTE:
ELECTRICAL BONDING
01 APPLY GREASE (MAT. NO. 03GBC1) TO THREADS
BEFORE ASSEMBLY INTO STUD ADJUSTER N_SB_521165_7_BBAC_02_04

Figure A-UBBAC - Sheet 02

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs and
Installation of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 872

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 003, 007

D E
(12)
(21)

(10)

DIM ’V1’
(11)
(22)

(23)
(14)
(13)
26 F

C D
TYPICAL
TYPICAL

SPOOL LOCK SCREW

LOCK SCREW POSITION
DIM ’V2’

E
TYPICAL
F
TYPICAL

N_SB_521165_7_BBAC_03_03

Figure A-UBBAC - Sheet 03

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs and
Installation of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 873

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 003, 007

DIM ’Y’ 02
02 DIM ’Z’

DIM ’X’

G
VIEW LOOKING UP

(17)

RIGGING
SPACERS

H
VIEW LOOKING UP

NOTE:
02 USED AT POSITION A ONLY N_SB_521165_7_BBAC_04_01

Figure A-UBBAC - Sheet 04

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs and
Installation of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 874

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 006, 009 thru 011, 019

MLG

(15)

B (32)

C AFTER
C (24) (25)

3
A
5
1
LH SHOWN
RH SIMILAR
(17)

01 (4)
(20)
(30)

6
9

(18) 8
26 (31)
(19) G H (29)

A
NOTE:
ELECTRICAL BONDING
01 APPLY GREASE (MAT. NO. 03GBC1) TO THREADS
BEFORE ASSEMBLY INTO STUD ADJUSTER N_SB_521165_7_BBAD_01_04

Figure A-UBBAD - Sheet 01

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs and
Installation of the LH and RH Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 875

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 006, 009 thru 011, 019

AFTER
(24) (25)

3
5
1

(28)
01 (4)

(30)

7
9
8
(31)
(16) G (29)

(39)
(40) 27
B

NOTE:
ELECTRICAL BONDING
01 APPLY GREASE (MAT. NO. 03GBC1) TO THREADS
BEFORE ASSEMBLY INTO STUD ADJUSTER N_SB_521165_7_BBAD_02_04

Figure A-UBBAD - Sheet 02

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs and
Installation of the LH and RH Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 876

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 006, 009 thru 011, 019

D E
(12)
(21)

(10)

DIM ’V1’
(11)
(22)

(23)
(14)
(13)
26 F

C D
TYPICAL
TYPICAL

SPOOL LOCK SCREW

LOCK SCREW POSITION
DIM ’V2’

E
TYPICAL
F
TYPICAL

N_SB_521165_7_BBAD_03_03

Figure A-UBBAD - Sheet 03

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs and
Installation of the LH and RH Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 877

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 006, 009 thru 011, 019

DIM ’Y’ 02
02 DIM ’Z’

DIM ’X’

G
VIEW LOOKING UP

(17)

RIGGING
SPACERS

H
VIEW LOOKING UP

NOTE:
02 USED AT POSITION A ONLY N_SB_521165_7_BBAD_04_01

Figure A-UBBAD - Sheet 04

Replace the LH and RH MLG Fixed Fairing Assembly Upper and Lower Forward Attachment Studs and
Installation of the LH and RH Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 878

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 001, 004 thru 005, 014 thru 015

B
DIM V

DIM T
A (AT POSITIONS
H AND J)

POSITION H A A
RIB2
DIM S
RIB3
RIB4 B B
A

FIXED POSITION J
UNDERWING B
PANEL
B A
HINGE
DOOR
C C
E E
D

FIXED
FAIRING
SHROUD D
BOX

A
DIM Q

DIM W
DIM R

DIM P
DIM X
C C D D E E
NEGATIVE STEP ILLUSTRATED
N_SB_521165_7_BCAA_01_01

Figure A-UBCAA - Sheet 01

Installation Dimensions of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 879

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 001, 004 thru 005, 014 thru 015

265 mm
(10.433 in)

420 mm
(16.575 in)

01 (36) 36
02

F
W
D

B INBD

NOTE:
01 BOND WITH ADHESIVE (MAT. NO. 05EML8)
02 AFTER MARKING, APPLY CLEAR VARNISH (MAT. NO. 04QAB2)
N_SB_521165_7_BCAA_02_00

Figure A-UBCAA - Sheet 02

Installation Dimensions of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 880

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 002, 008, 012 thru 013, 016 thru 018, 020

B
DIM V

DIM T
A (AT POSITIONS
H AND J)

POSITION H A A
RIB2
DIM S
RIB3
RIB4 B B
A

FIXED POSITION J
UNDERWING B
PANEL
B A
HINGE
DOOR
C C
E E
D

FIXED
FAIRING
SHROUD D
BOX

A
DIM Q

DIM W
DIM R

DIM P
DIM X
C C D D E E
NEGATIVE STEP ILLUSTRATED
N_SB_521165_7_BCAB_01_01

Figure A-UBCAB - Sheet 01

Installation Dimensions of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 881

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 002, 008, 012 thru 013, 016 thru 018, 020

265 mm
(10.433 in)

420 mm
(16.575 in)

01 (36) 36
02

F
W
D

B INBD

NOTE:
01 BOND WITH ADHESIVE (MAT. NO. 05EML8)
02 AFTER MARKING, APPLY CLEAR VARNISH (MAT. NO. 04QAB2)
N_SB_521165_7_BCAB_02_00

Figure A-UBCAB - Sheet 02

Installation Dimensions of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 882

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 003, 007

F
DIM V

DIM T
A B (AT POSITIONS
H AND J)

POSITION H A A
RIB2
DIM S
RIB3
RIB4 B B
A

FIXED POSITION J
UNDERWING B
PANEL
B A
HINGE
DOOR
C C
E E
D
FIXED
FAIRING
SHROUD
BOX D

A
DIM Q

DIM W
DIM R

DIM P
DIM X
C C D D E E
NEGATIVE STEP ILLUSTRATED
N_SB_521165_7_BCAC_01_01

Figure A-UBCAC - Sheet 01

Installation Dimensions of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 883

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 003, 007

F 32
D G

BLACK MARKS
(3 PLACES)

G F
C
E C
B FWD
TRACK 1A VIEW DIM A
FROM BELOW
32

30 mm
(1.20 in) 30 mm
FWD D (1.20 in)

02
1.5 mm MAX
(0.060 in)

30 mm 02
(1.20 in)

32 BLACK
02
LINE
32 FWD E
33 01

01 34 34 01
F F

01 35 32
NOTE: G G
01 APPLY SEALANT (MAT. NO. 06AEA1 OR 06AEB2).
02 MARK LINES WITH (MAT. NO. 04JMD3).
N_SB_521165_7_BCAC_02_00

Figure A-UBCAC - Sheet 02

Installation Dimensions of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 884

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 003, 007

265 mm
(10.433 in)

420 mm
(16.575 in)

03 (36) 36
04

F
W
D

F INBD

NOTE:
03 BOND WITH ADHESIVE (MAT. NO. 05EML8)
04 AFTER MARKING, APPLY CLEAR VARNISH (MAT. NO. 04QAB2)
N_SB_521165_7_BCAC_03_00

Figure A-UBCAC - Sheet 03

Installation Dimensions of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 885

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 006, 009 thru 011, 019

F
DIM V

DIM T
A B (AT POSITIONS
H AND J)

POSITION H A A
RIB2
DIM S
RIB3
RIB4 B B
A

FIXED POSITION J
UNDERWING B
PANEL
B A
HINGE
DOOR
C C
E E
D
FIXED
FAIRING
SHROUD
BOX D

A
DIM Q

DIM W
DIM R

DIM P
DIM X
C C D D E E
NEGATIVE STEP ILLUSTRATED
N_SB_521165_7_BCAD_01_01

Figure A-UBCAD - Sheet 01

Installation Dimensions of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 886

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 006, 009 thru 011, 019

F 32
D G

BLACK MARKS
(3 PLACES)

G F
C
E C
B FWD
TRACK 1A VIEW DIM A
FROM BELOW
32

30 mm
(1.20 in) 30 mm
FWD D (1.20 in)

02
1.5 mm MAX
(0.060 in)

30 mm 02
(1.20 in)

32 BLACK
02
LINE
32 FWD E
33 01

01 34 34 01
F F

01 35 32
NOTE: G G
01 APPLY SEALANT (MAT. NO. 06AEA1 OR 06AEB2).
02 MARK LINES WITH (MAT. NO. 04JMD3).
N_SB_521165_7_BCAD_02_00

Figure A-UBCAD - Sheet 02

Installation Dimensions of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 887

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 006, 009 thru 011, 019

265 mm
(10.433 in)

420 mm
(16.575 in)

03 (36) 36
04

F
W
D

F INBD

NOTE:
03 BOND WITH ADHESIVE (MAT. NO. 05EML8)
04 AFTER MARKING, APPLY CLEAR VARNISH (MAT. NO. 04QAB2)
N_SB_521165_7_BCAD_03_00

Figure A-UBCAD - Sheet 03

Installation Dimensions of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 888

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 001, 004 thru 005, 014 thru 015

MLG 01 01

A A
B
A 01
A
TYPICAL

A A 01

B
LH SHOWN
RH SIMILAR
01

01
02
02

01

01
A A
TYPICAL 01
NOTE:
01 APPLY SEALANT (MAT. NO. 06AAA1).
02 WRAP WIRELOCKING TAIL AROUND LOCK NUT. APPLY SEALANT (MAT. NO. 06AAA1)
TO THE TAILS, THREADS AND LOCK NUT.
N_SB_521165_7_BDAA_01_02

Figure A-UBDAA - Sheet 01

Sealing of the Upper and Lower Attachment Studs of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 889

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 002, 008, 012 thru 013, 016 thru 018, 020

MLG 01 01

A A
B
A 01
A
TYPICAL

A A 01

B
LH SHOWN
RH SIMILAR
01

01
02
02

01

01
A A
TYPICAL 01
NOTE:
01 APPLY SEALANT (MAT. NO. 06AAA1).
02 WRAP WIRELOCKING TAIL AROUND LOCK NUT. APPLY SEALANT (MAT. NO. 06AAA1)
TO THE TAILS, THREADS AND LOCK NUT.
N_SB_521165_7_BDAB_01_01

Figure A-UBDAB - Sheet 01

Sealing of the Upper and Lower Attachment Studs of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 890

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 003, 007

MLG 01 01

A A
B
A 01
A
TYPICAL

A A 01

B
LH SHOWN
RH SIMILAR
01

01
02
02

01

01
A A
TYPICAL 01
NOTE:
01 APPLY SEALANT (MAT. NO. 06AAA1).
02 WRAP WIRELOCKING TAIL AROUND LOCK NUT. APPLY SEALANT (MAT. NO. 06AAA1)
TO THE TAILS, THREADS AND LOCK NUT.
N_SB_521165_7_BDAC_01_01

Figure A-UBDAC - Sheet 01

Sealing of the Upper and Lower Attachment Studs of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 891

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN

**CONF 006, 009 thru 011, 019

MLG 01 01

A A
B
A 01
A
TYPICAL

A 01
A
A

B
LH SHOWN
RH SIMILAR
01

01
02
02

01

01
A A
TYPICAL 01
NOTE:
01 APPLY SEALANT (MAT. NO. 06AAA1).
02 WRAP WIRELOCKING TAIL AROUND LOCK NUT. APPLY SEALANT (MAT. NO. 06AAA1)
TO THE TAILS, THREADS AND LOCK NUT.
N_SB_521165_7_BDAD_01_01

Figure A-UBDAD - Sheet 01

Sealing of the Upper and Lower Attachment Studs of the LH and RH MLG Fixed Fairing Assembly

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 892

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
Appendix 01: Manpower Gantt Chart

**CONF ALL

For an explanation of the manhours and elapsed time, refer to the next page.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 1

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
Appendix 01: Manpower Gantt Chart

**CONF ALL

01
ELAPSED TIME ASSUMPTION SERVICE BULLETIN No A320−52−1165
02

STEPS MH PER ET/S

GET ACCESS 4.00 4 1.00

REMOVE THE LH MLG FIXED FAIRING ASSEMBLY 1.00 2 0.50

REMOVE THE RH MLG FIXED FAIRING ASSEMBLY 1.00 2 0.50

REPLACE THE LH FIXED FAIRING ASSEMBLY UPPER AND LOWER 1.00 2 0.50
FORWARD ATTACHMENT STUDS

REPLACE THE RH FIXED FAIRING ASSEMBLY UPPER AND LOWER 1.00 2 0.50
FORWARD ATTACHMENT STUDS

INSTALL THE LH MLG FIXED FAIRING ASSEMBLY 4.00 2 2.00

INSTALL THE RH MLG FIXED FAIRING ASSEMBLY 4.00 2 2.00

REIDENTIFY THE LH MLG FIXED FAIRING ASSEMBLY 0.50 1 0.50

REIDENTIFY THE RH MLG FIXED FAIRING ASSEMBLY 0.50 1 0.50

TEST 1.00 2 0.50

CLOSE−UP 4.00 4 1.00

0 1 2 3 4 5 6
SB ELAPSED TIME
TOTAL MANHOURS 22.00 (HOURS)
SB ELAPSED TIME 6.00

NOTE:
01 THIS CHART IS ONLY A PROPOSAL.
OPERATORS MAY DETERMINE THAT ANOTHER WAY
TO DO THE WORK IS MORE SUITABLE FOR THEM.
MH : MANHOURS
PER : NUMBER OF PERSONS 02 IF A VSB IS INVOLVED, THE ASSOCIATED MANHOURS
ET/S: ELAPSED TIME PER STEP ARE NOT REFLECTED IN THIS GANTT CHART. N_SB_521165_7_AAAA_01_04

Figure A-UAAAA - Sheet 01

Manpower Gantt Chart

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 2

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
Appendix 02: Configuration Definition Table

**CONF ALL

For further information concerning the Configuration Definition, refer to the next page.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 1

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
Appendix 02: Configuration Definition Table

**CONF ALL

STATUS OF AIRCRAFT BEFORE ACCOMPLISHMENT

OF SERVICE BULLETIN No A320−52−1165

MODIFICATIONS / SERVICE BULLETINS

MOD 24192 MOD 27716

MOD 20139 MOD 20167 MOD 24521 MOD 24522 MOD 26096 MOD 30040 MOD 36540 MOD 38893
CONFIG J0935 SB 52−1081 J1969
G0003 J0127 J0927 J1274 J1744 J1786 J2608 J2903
SB 52−1050 SB 52−1100
CONF 001 X
CONF 002 X X
X X
CONF 003
X X X
CONF 004 X X
CONF 005 X X
X X X
CONF 006
X X X X
CONF 007 X X X X
CONF 008 X X X
CONF 009 X X X X X X
CONF 010 X X X X X X X
CONF 011 X X X X X
CONF 012 X X X
CONF 013 X X X X X X X
CONF 014 X X X
CONF 015 X X X X
X X X X
CONF 016 X X X X
X X X X X
CONF 017 X X X X X
CONF 018 X X X X X X
CONF 019 X X X X X X X X
CONF 020 X X X X X X X X

NOTE:
"X" IS USED FOR MODIFICATIONS OR SERVICE BULLETINS
EMBODIED BEFORE ACCOMPLISHMENT OF THIS SERVICE BULLETIN N_SB_521165_7_ABAA_01_06

Figure A-UABAA - Sheet 01

Configuration Definition Table

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 2

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
Service Bulletin REPORTING

TITLE: DOORS - MAIN GEAR DOORS - INTRODUCE NEW FAIRING

ATTACHMENT STUD ASSEMBLIES
MODIFICATION No.: 155648J3676

SB Reporting status

This Service Bulletin will only be incorporated into affected customized Maintenance and Flight
Operations Products if it is duly reported to Airbus.

General information

The SB Reporting policy is published in ISI 00.00.00135. This document provides information regarding:
the SB Reporting means and benefits, the update of customized Maintenance Products and customized
Flight Operations Products.

If this Service Bulletin has an operational impact, refer to paragraph "Flight Operations Products" for
further information on the update of affected Flight Operations Products.

SB Reporting procedure

Standard practice to report SB is to use the online reporting application on AirbusWorld.

Refer to ISI 00.00.00179:

- For complete information on reporting means to Airbus. Question 2 "What are the standard
practices for SB reporting?"
- If this SB requires previous or simultaneous accomplishment of other SBs, Question 3 "What about
the reporting of prerequisite Service Bulletin?"

NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting. It is revised on a
regular basis.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 1

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.

 @A318/A319/A320/A321
SERVICE BULLETIN
QUALITY PERCEPTION FORM

Use this form to tell us what is your perception of the quality of this Service Bulletin. The reported data
that you provide us will be used to analyse areas of difficulties and to take corrective action to further
improve the quality of our Service Bulletins.
We thank you for the time you have taken in completing this form.

(Please rate on a scale of 1 to 4, with 4 being the highest score)

- Quality rating of this SB 4 3 2 1

- Quality rating of the Accomplishment Instructions 4 3 2 1
- Quality rating of the Illustrations 4 3 2 1
- Is this SB easy to understand ? Y/N

If you have had difficulties in the accomplishment of this SB please quote below the area(s) and give a
short description of the issue.

Planning Material Instructions

X Effectivity X Kit content X Preparation

X Reason X List of Materials Operator Supplied X Mod/Inspection
X Manpower X Industry support X Test
X References X Re-identification X Close-Up
X Publication X Tooling X Illustrations

Comments:

Operator: Date:

Name/Title:

Please return this form to:

AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX FRANCE

Attn : SEM4 Service Bulletins Management

FAX : (33) 5 61 93 42 51

Or via your Resident Customer Support Office.

7 DATE: Nov 03/14 SERVICE BULLETIN No.: A320-52-1165

REVISION No.: 03 - Nov 09/17 Page: 1

Printed in FRANCE © AIRBUS S.A.S. 2007. All rights reserved.