1.

In a transformer

a. All turns are equally insulated

b. The end turns are more strongly insulated
c. The end turns are closely wound
d. The end turns are widely separated

2. Laminated insulations coated with varnish are normally used in the transformer

a. To reduce reluctance of magnetic path

b. To reduce the effect of eddy current
c. To increase the reluctance of magnetic path
d. To reduce the hysteresis effect

3. The required thickness of lamination in a transformer decreases when

a. The applied frequency increases

b. The applied frequency decreases
c. The applied voltage increases
d. The applied voltage decreases

4. Oil in transformer is used to

a. Transfer electrical energy

b. Insulate the windings
c. Cool the windings
d. None of the above

5. The following arrangement will reduce the reluctance of magnetic path of the transformer.

a. A
b. B
c. C
d. D

6. The windings of a transformer are divided into several coils because

a. It is difficult to wind as one coil

b. It reduces voltage per coil
c. It requires less insulation
d. None of the above
7. The size and construction of bushings in a transformer depend upon the

a. Size of winding
b. Size of tank
c. Current flowing
d. Voltage supplied

8. Transformer humming sound is reduced by the

a. Proper bracing of transformers assemblies

b. Proper insulation
c. Proper design
d. Proper design of winding

9. Sludge in transformer oil is due to

a. Decomposition of oil
b. Decomposition of insulation
c. Moisture content in oil
d. None of the above

10. A transformer used only for electrical isolation between two circuits has turns ratio which is

a. More than unity

b. Less than unity
c. Equal to unity
d. More than 0.5

11. If 90 percent of normal voltage and 90 percent of normal frequency are applied to a transformer, the
percent change in hysteresis losses will be

a. 20%
b. 4.7%
c. 19%
d. 21%

12. Open circuit test for transformer is used to calculate:

a. Core loses
b. Ohmic losses
c. Hysteresis losses
d. Eddie current losses

13. If 110 percent of normal voltage and 110 percent of normal frequency is applied to a transformer, the
percentage change of eddy current losses will be

a. 10%
b. 20%
c. 25%
d. 21%
14. A transformer has two 2,400 V primary coils and two 240 V coils. By proper connection of the windings, the
transformation ratio that can be obtained is

a. 10
b. 5
c. 20
d. 9

15. A single-phase, 2,200/200 V transformer takes 1 A at the HT side or no load at a power factor of 0.385
lagging. The iron losses are

a. 167 W
b. 77 W
c. 88 W
d. 98 W

16. Neglecting resistance, at constant flux density, the power required per kilogram to magnetize the iron core
of a transformer is 0.8 W at 25 Hz and 2.04 W at 60 Hz. The power required per kilogram for 100 Hz is

a. 3.8 W
b. 3.63 W
c. 3.4 W
d. 5.2 W

17. Select the correct statement:

a. emf per turn of both the windings are equal

b. emf per turn in HV winding is more than the emf per turn in LV winding
c. emf per turn in HV winding is less than the emf per turn in LV winding

18. The flux involved in the emf equation of a transformer has

a. rms value
b. Average value
c. Total value
d. Maximum value

19. The no-load current in a transformer lags the applied voltage by

a. 90° – 95°
b. About 80° – 85°
c. 0° – 15°
d. About 110°

20. High leakage impedance transformers are used for applications such as

a. Power distribution
b. Electrical toys
c. Arc welding
d. Fluorescent lamps
21. A transformer 2,000 kVA, 250 Hz is operated at 50 Hz. Its kVA rating should be revised to

a. 400 kVA
b. 10,000 kVA
c. 2,000 kVA
d. Cannot be revised

22. The transformer which will have the largest size is

a. 100 kVA, 25 Hz
b. 100 kVA, 100 Hz
c. 100 kVA, 50 Hz
d. 100 kVA, 60 Hz

23. The magnetic flux of a transformer follows

a. High reluctance path

b. Low reluctance path
c. Low conductivity path
d. High conductivity path

24. The efficiency of a transformer is usually in the range of

a. 50–60%
b. 65–75%
c. 70–90%
d. 90–98%

25. Transformer is laminated to reduce

a. Hysteresis loss
b. Eddy current loss
c. Partly (a) and partly (b)
d. Increases exciting current

26. Transformer changes the value of

a. Power
b. Frequency
c. Voltage
d. Current

27. Transfer of electrical power from primary to secondary in a transformer takes place

a. Electrically
b. Electromagnetically
c. Magnetically
d. None of these

28. The thickness of a 50 Hz transformer lamination is

a. 0.35 cm
b. 0.35 mm
c. 0.33 m
d. 0.30 cm
29. A power transformer is a constant

a. Current device
b. Voltage device
c. Power device
d. Main flux device

30. The value of flux in the emf equation of a transformer is

a. rms
b. Average
c. Maximum
d. Integral wave cycle

31. The leakage flux in a transformer depends upon the value of

a. Load current
b. Supply frequency
c. Mutual flux
d. None of these

32. The voltage regulation of a transformer at full-load 0.8 PF. lag is 6 percent. Its voltage regulation at full-load
0.8 power factor lead will be

a. Negative
b. 54%
c. Positive
d. Zero

33. The full-load efficiency of a transformer at 0.85 PF. lag is 97 percent. Its efficiency at full load 0.85 power
factor lead will be

a. 99%
b. 96%
c. 97%
d. 98%

34. If a load on secondary side of a transformer increases, the current on the primary side

a. Remains constant
b. Increases
c. Decreases
d. none of these

35. If a sinusoidal exciting current is applied to a transformer, the mutual flux produced is

a. Negative
b. Sinusoidal
c. Zero
d. Flat top
36. To get sinusoidal flux in a transformer the mutual flux produced is

a. Non-sinusoidal
b. Sinusoidal
c. Direct current
d. Zero

37. A 220V, 150V bulb is connected in series with the primary of a 220/1,100 V, 50 Hz transformer. If the load
on the secondary side is disconnected, the brightness of the bulb will

a. Decrease
b. Increase
c. Be unaffected
d. Decrease to a very low value

38. The open circuit test of a transformer gives information about

a. Core losses of the transformer

b. Cu losses of the transformer
c. Exciting current
d. None of these

39. The short circuit test of a transformer gives the information of

a. Cu losses of the transformer

b. Core losses of the transformer
c. Winding circuit impedance
d. None of these

40. During testing of a transformer

a. Both SC and OC tests are performed at rated current

b. Both SC and OC tests are performed at rated voltage
c. OC test is performed at rated voltage
d. SC test is performed at rated current

41. All-day efficiency of a transformer is

a. Equal to its power efficiency

b. Less than its power efficiency
c. More than its power efficiency
d. None of these

42. Routine efficiency of a transformer depends upon the value of

a. Load current
b. Supply frequency
c. Power factor of load
d. Both (a) and (b)
43. A ferrite core has less eddy current loss than an iron core because ferrites have

a. Lower permeability
b. High hysteresis
c. Alnico as the main constituent
d. High resistance

44. The maximum regulation of a transformer occurs at a power factor of

a. (a)
b. (b)
c. (c)
d. (d)

45. The zero of regulation of a transformer occurs at a power factor of

a. (a)
b. (b)
c. (c)
d. (d)

46. Circular coil sections are used because they

a. Reduce iron material

b. Reduce copper material
c. Have the strongest mechanical shape
d. All of these

47. A transformer is connected to a constant voltage source. If the supply frequency decreases, the magnetic
flux in the core will

a. Increase towards saturation

b. Decrease
c. Remain unchanged
d. None of these

48. The power in autotransformer is transferred through

a. Inductive process
b. Convection process
c. Conduction process
d. All of these

49. The cross-sectional area of the common portion of an autotransformer is

a. Kept constant
b. Proportionally decreased
c. Proportionally increased
d. None of these
50. The efficiency of an autotransformer for the same output compared to a two-winding transformer is

a. Greater
b. Lesser
c. Poor
d. None of these

51. The condition for successful parallel operation of transformer is

a. Correct polarity
b. Per unit impedance based on their rating should be equal
c. Identical voltage and frequency rating
d. Equal ratio of equivalent resistance to reactance
e. All of these

52. During parallel operation of transformers incorrect polarity will result in

a. Open circuit
b. Dead short circuit
c. Regeneration of power
d. Power factor of transformer will be different from that of the connected load

53. In an autotransformer of voltage ratio

𝑉$
𝑉1 and V1 > V2, the fraction of power transferred inductively is

a. A
b. B
c. C
d. D

54. A 10 kVA, 400/200 V single-phase transformer with 10 percent impedance draws a steady short circuit line
current of

a. 50 A
b. 150 A
c. 250 A
d. 350 A

55. A 400/100 V, 10 kVA two-winding transformer is reconnected as an autotransformer across a suitable

voltage source. The maximum kVA is

a. 50 kVA
b. 15 kVA
c. 12.5 kVA
d. 8.75 kVA

56. An autotransformer having a transformation ratio of 0.8 supplies a load of 10 kW. The power transferred
inductively from the primary to the secondary is

a. 10 kW
b. 8 kW
c. 2 kW
d. Zero
57. A single-phase induction regulator is a constant input transformer to obtain smooth variation of the output
voltage by varying the

a. Ratio of turns between primary and secondary winding

b. Frequency
c. Flux-density in the core
d. Angle between the magnetic forces of the primary and secondary windings

58. In operating a 400 Hz transformer at 50 Hz

a. Only voltage is reduced in the same proportion as the frequency

b. Only kVA is reduced in the same proportion as the frequency
c. Both voltage and kVA rating are reduced in the same proportion as the frequency
d. None of the above

59. In performing the short circuit test of a transformer

a. High-voltage side is usually short-circuited

b. Low-voltage side is usually short-circuited
c. Any side is short-circuited with preference
d. None of these

60. In performing open circuit test of a transformer

a. High voltage is usually kept open

b. Low voltage is usually kept open
c. Any side can be kept open
d. None of the above

61. Transformer core usually uses grain-oriented laminated sheets. The grain orientation reduces

a. Copper loss
b. Eddy current loss
c. Hysteresis loss
d. None of the above

62. In the circuit model of a transformer, the core loss is represented as

a. Series resistance
b. Series inductance
c. Shunt resistance
d. Shunt inductance

63. While performing short circuit test on a transformer, the impressed voltage magnitude is kept constant,
but the frequency is increased. The short circuit current will

a. Increase
b. Decrease
c. Remain the same
d. None of the above
64. A transformer has a hysteresis loss of 30 W at 240 V, 60 Hz. The hysteresis loss at 200 V, 50 Hz will be

a. 20.8 W
b. 25 W
c. 30 W
d. 36 W

65. In a transformer, the exciting current will be in phase quadrature with the impressed voltage provided

a. Only the leakage impedance drop is ignored

b. Only the core loss is ignored
c. Both the leakage and impedance drop and the core loss are ignored
d. Only no-load copper loss is ignored

66. Magnetizing impedance of a transformer is determined by

a. Short circuit test

b. Open circuit test
c. Both open circuit and short circuit tests
d. None of these

67. A transformer is to be tested at full-load conditions consuming only losses from the mains. We do

a. Load test
b. Open circuit and short circuit tests
c. Back-to-back test
d. None of these

68. In a transformer operating at constant voltage if the input frequency increases the core loss will

a. Increase
b. Decrease
c. Remain constant
d. Increase as the square of the frequency

69. Grain-oriented laminated sheet steel in a transformer reduces

a. Copper loss
b. Eddy current loss
c. Hysteresis loss
d. None of above

70. R1 is the resistance of the primary winding of a transformer. The turns ratio in terms of primary to secondary
is a, the equivalent resistance of the primary referred to as secondary is

a. R1/a
b. a2*R1
c. R1/a^2
d. None of these
71. Choose the correct statement:

a. emf per turn in high-voltage winding is more than the emf per turn in low-voltage winding
b. emf per turn in both the winding are equal
c. emf per turn in both the windings are not equal
d. None of these

72. If E2 be the induced emf in secondary winding and V2 be the terminal voltage during load, the regulation
of the transformer is given by

a. (A)
b. (B)
c. (C)
d. (D)

73. One transformer has leakage impedance of 1 + j 4 Ω and 3 + j 4 Ω for its primary and secondary windings,
respectively. The transformer has

a. Low voltage primary

b. High voltage primary
c. Medium voltage primary
d. Insufficient data

74. A single-phase transformer has its maximum efficiency at 60 percent of full load. At full load copper loss
will be

a. Equal to core loss

b. Less than core loss
c. More than core loss
d. Zero

75. The flux in a magnetic core is alternating sinusoidally at a frequency of 600 Hz. The maximum flux density
is 2 T and eddy current loss is 15 W. If the frequency is raised to 800 Hz and maximum flux density reduced
to 1.5 T, the eddy current loss will be

a. Same
b. Reduced to half
c. Doubled
d. Increased by 50%

76. The core flux in a transformer depends mainly on

a. Supply voltage
b. Supply voltage and frequency
c. Supply voltage, frequency and load
d. Supply voltage and load but independent of frequency
77. If the signal is power doubled at a given transmitter, what is the decibel (dB) increase?

a. 0.5 db
b. 2 db
c. 3 db
d. 4 db

78. HDL design is having inputs and outputs. Who should be giving the inputs and outputs in VHDL?

a. Architecture Declaration
b. Entity Declaration
c. Both Architecture and Entity
d. d. …..

79. For a 12 AWG wire we should use CB rating:

a. 10 A
b. 15 A
c. 20 A
d. 30 A

80. Three resistors are connected in series l parallel combination what are the possibilities to get different total
resistance:

a. 3
b. 4
c. 5
d. 6

81. Is used to vary transmitted or received signal

a. Waveguide
b. Antenna dish
c. …
d. …

82. Two test terminals: f short circuit 3 A, Connected to conductance of 0.2 S across 5 V (Check question)

a. Current 3 A, conductance 0.2 S

b. Current 1 A, conductance 0.2 S
c. Current 3 A, conductance 0.6 S
d. Current 1 A, conductance 0.6 S

83. Permanent magnet moving coil instrument (PMMC) type instruments normally use:

a. Air friction damping

b. Fluid friction damping
c. Eddy current damping
d. None of the above
84. Inter-symbol interface is eliminated by:
 a. Nyquist
b. Pulse code
c. SSB Modulator

85. Problem for damping ratio

86. What is the transfer function of this system?

87. The total resistance of a circuit is 680 ohms, the percentage of the volt appearing across 47 ohm resistance
that makes as part of the total series resistance is:

a. 68 %
b. 47 %
c. 69 %
d. 6.9 %

88. Which one of the following is not described high conductivity?

a. Ceramic
b. Copper
c. Aluminum
d. Silver

89. Write the wind Load Equation with details?

90. Filaments in incandescent light bulbs are made of

a. Carbon
b. Aluminum
c. nickel
d. tungsten
91. certain communication channel has a signal to noise ratio of 7 and bandwidth of 10 KHZ what is the channel
capacity?

a. 30 bps
b. 80 bps
c. 3000 bps
d. 30,000 bps

92. An antenna has effective aperture of 10 m2 what is the additional information required to determine
delivered power?

a. Power density
b. Power losses
c. Space losses
d. Total torque

93. Radio station 50 KW power emitter and gain 1.5, at 10 KM what will be the output power density? (Check
question)

a. 75 mW/m2
b. 33 mW/m2

RF Antenna AR1 AR2 AR3

Noise factor 5 dB 15 dB 25 dB
Gain 10 dB 15 dB 20 dB
Band 160 MHZ 16 MHZ 30 MHZ
94. Find the total NF for below table.
95. Two tower antennas with Hight of 90 m, what is the max distance between
them for good communication

a. 20 km
b. 30 km
c. 40 km
d. 80 km

96. A digital signal processor (DSP) is design to perform FFT operations for a digital
oscilloscope that utilizes a 12-bit A/ D Converter. The most cost effective ALU
architecture for this CPU is a:

a. Fixed -point multiplier with an 8-bit data path.

b. Floating -point multiplier with an 8-bit data path.
c. Fixed -point multiplier with a 16-bit data path.
d. Floating -point multiplier with a 16-bit data path.

97. Fiber optic communication

a. FDM b. WDM c. CDM

98. Talk in details about Real Time Systems?

99. Talk about session hijacking and the methods hackers use to do hijack and how
to prevent the network from such attack?

100. What is the use of a station pointer?

a. For making soundings in water bodies.

b. For plotting of soundings in harbor area.
c. For making sunken shipping hazards
d. For making tidal observations.

101. Consider the following statements “collision diagram is used to “

a. Study accident pattern

b. Eliminate accidents
c. Determine remedial measures
d. Make statistical analysis of accidents