Scribd
Upload
36 views

Coding File

Uploaded by

Praveen
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
36 views

Coding File

Uploaded by

Praveen
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 3

#include <EEPROM.

h>
#include <LiquidCrystal.h>
LiquidCrystal lcd(2, 3, 4, 5, 6, 7);

#define ThermistorPin A0 // for Arduino microcontroller

#define bt_set A3
#define bt_up A4
#define bt_down A5

#define fan 9
#define buzzer 13

long ADC_Value;
float R1 = 10000; // value of R1 on board
float logR2, R2, T;

//steinhart-hart coeficients for thermistor


float c1 = 0.001129148, c2 = 0.000234125, c3 = 0.0000000876741;

float setL_temp = 30.5;


float setH_temp = 39.5;
float temp=0;

int duty_cycle;
int Set=0, flag=0, flash=0;

void setup() {// put your setup code here, to run once:

pinMode(ThermistorPin, INPUT);

pinMode(bt_set, INPUT_PULLUP);
pinMode(bt_up, INPUT_PULLUP);
pinMode(bt_down, INPUT_PULLUP);

pinMode(fan, OUTPUT);
pinMode(buzzer, OUTPUT);

lcd.begin(16, 2); // Configura lcd numero columnas y filas


lcd.clear();
lcd.setCursor (0,0);
lcd.print(" Welcome To ");
lcd.setCursor (0,1);
lcd.print(" Temp Control ");

if(EEPROM.read(0)==0){}
else{
EEPROM.put(10, setL_temp);
EEPROM.put(15, setH_temp);
EEPROM.write(0, 0);
}
EEPROM.get(10, setL_temp);
EEPROM.get(15, setH_temp);

delay(2000); //wait 1000 mS for next measure


lcd.clear();
}
void loop(){

ADC_Value=0;
for(int i=0; i<100; i++) {
ADC_Value = ADC_Value+analogRead(ThermistorPin);
delay(1);
}

ADC_Value=ADC_Value/100;
R2 = R1 * (1023.0 / (float)ADC_Value - 1.0); //calculate resistance on thermistor
logR2 = log(R2);
temp = (1.0 / (c1 + c2*logR2 + c3*logR2*logR2*logR2)); // temperature in Kelvin
temp = temp - 273.15; //convert Kelvin to Celcius

int value1 = temp*10;


int value2 = setL_temp*10;
int value3 = setH_temp*10;

duty_cycle = map(value1, value2, value3, 0, 100);


if(duty_cycle>100)duty_cycle=100;
if(duty_cycle<0)duty_cycle=0;

if(temp<setL_temp){digitalWrite(fan, 0);}
else{analogWrite(fan, (duty_cycle*2)+55); }

if(temp>setH_temp){digitalWrite(buzzer, HIGH); delay(100);}

if(digitalRead(bt_set)==0){
digitalWrite(buzzer, HIGH);
if(flag==0){ flag=1;
Set=Set+1;
if(Set>2){Set=0; flash=0;}
delay(200);
}
}else{flag=0;}

if(digitalRead(bt_up)==0){
digitalWrite(buzzer, HIGH);
if(Set==1){setL_temp = setL_temp+.1;EEPROM.put(10, setL_temp);}
if(Set==2){setH_temp = setH_temp+.1;EEPROM.put(15, setH_temp);}
delay(10);
}

if(digitalRead(bt_down)==0){
digitalWrite(buzzer, HIGH);
if(Set==1){setL_temp = setL_temp-.1;EEPROM.put(10, setL_temp);}
if(Set==2){setH_temp = setH_temp-.1;EEPROM.put(15, setH_temp);}
delay(10);
}

if(Set==0){

lcd.setCursor(0,0);
lcd.print(" Temp: ");
lcd.print(temp,1);
lcd.write(223);
lcd.print("C ");

lcd.setCursor(0,1);
lcd.print(" Fan Speed:");
if(duty_cycle<100)lcd.print(" ");
lcd.print(duty_cycle);
lcd.print("% ");

}else{
lcd.setCursor(0,0);
lcd.print(" Setting Mode ");

lcd.setCursor(0,1);
lcd.print("L:");
if(Set==1 && flash==1){lcd.print(" ");}
else{lcd.print(setL_temp,1);}
lcd.print("C ");

lcd.setCursor(9,1);
lcd.print("H:");
if(Set==2 && flash==1){lcd.print(" ");}
else{lcd.print(setH_temp,1);}
lcd.print("C ");
}

if(Set>0){flash=!flash;}
delay(1); //wait 1 mS for next measure
digitalWrite(buzzer, LOW);
}

You might also like