PRODUCT DATA SHEET
SikaEmaco® S 488 PM
(formerly MEmaco S 488PM)
Polymer Modified, Shrinkage Compensated, Fibre Reinforced, Thixotropic Repair Mortar
DESCRIPTION FEATURES
SikaEmaco® S 488 PM is a polymer modified, single SikaEmaco® S 488 PM provides the following benefi-
component, cementitious, synthetic fibre reinforced, cial properties:
structural repair mortar that contains Portland Ce- ▪ Structural repair
ment, well graded sands, specially selected fibres ▪ Can be spray applied - rapid application of large
and additives to improve the fresh and hardened quantities
properties. ▪ Rapid strength gain and high final strength
Suitable for use in hot and tropical climatic conditions. ▪ Good water and oil resistance
▪ Low shrinkage behaviour
USES ▪ High abrasion resistance
▪ Good adhesion
SikaEmaco® S 488 PM is used for structural repair ▪ Easy to apply
work and suitable for: ▪ Low permeability
▪ Restoration works, repair of spalling and damaged
concrete in buildings, bridges, infrastructure and su-
perstructure works.
▪ Structural strengthening by increasing the bearing
capacity of the concrete structure by adding mortar
(section enlargement).
▪ Preserving or restoring passivity by increasing cover
with additional mortar and replacing contaminated
or carbonated concrete.
PRODUCT INFORMATION
Composition Polymer containing cementitious mortar with different additives and syn-
thetic fibres
Packaging 25 kg bags
Shelf life 12 months from date of production
Storage conditions Store in a cool, dry area in original sealed packaging and at temperatures
between +5 °C and +35 °C. Protect from direct sunlight, heat and moisture.
Appearance and colour Grey powder
Maximum grain size ~4 mm
Product Data Sheet
SikaEmaco® S 488 PM
September 2024, Version 02.01
020302000000002110
1/3
TECHNICAL INFORMATION
Compressive strength 1 Day 28 days (BS EN 1881: Part
w/p = 0.14 ≥ 25 N/mm2 ≥ 70 N/mm2 116)
Tensile adhesion strength ≥ 1.5 N/mm2 (or concrete failure) (BS EN 1542)
Chloride ion permeability ≤ 1000 Coulombs (cured 28 days) (ASTM C1202)
APPLICATION INFORMATION
Fresh mortar density ~2.19 kg/l (+25 °C)
Layer thickness Min. 10 mm
Max. 50 mm
Mixing ratio 3.5 - 4.0 L of water per 25 kg bag
Substrate temperature +5 °C min. / +40 °C max.
BASIS OF PRODUCT DATA APPLICATION INSTRUCTIONS
▪ All technical data stated in this Data Sheet are based SUBSTRATE QUALITY / PRE-TREATMENT
on laboratory tests. Actual measured data may vary
due to circumstances beyond our control. Substrates must be properly cured, structurally sound,
▪ Internal Reference - Version: MBS_CC-UAE/ free of any loose or friable particles, clean, dry and
Em_S488PM_04_16/v3/07_17/v4/09_19 free of any contaminants such as dust, dirt, oil, grease,
cement laitance or efflorescence.
FURTHER DOCUMENTATION ▪ The edges of repair areas should be cut vertically to a
min depth of 10 mm.
Method Statement ▪ The surface roughness should be prepared to minim-
um CSP 9 acording to ICRI
IMPORTANT CONSIDERATIONS ▪ Any contamination to be removed from the concrete
surface, perform adequate preparation techniques,
▪ Repair sections higher than 50 mm should be applied such as water-jet washing or blast cleaning, in order
in layers. to remove all traces of any materials that could re-
▪ When the ambient temperature is high during sum- duce the product's adhesion to the substrate.
mer months, special precautions must be taken so ▪ For applications in hot climates / environments and /
that the mixed material temperature is not above or on absorbent substrates, thoroughly pre-dampen
35°C. Please consult Sika Technical Department. the surface immediately prior to the product applica-
▪ Avoid application in direct sun and/or strong wind. tion, but avoid any ponding / standing water on the
▪ Do not add additional water during the surface fin- surface, which must not be damp to touch and not
ishing as this will cause discolouration and cracking. with a dark-matt / wet surface appearance i.e. it
▪ Do not overwork the finished surface as this will pro- must be saturated surface dry (SSD).
duce a cement rich surface texture, which may cause ▪ Steel surfaces shall be prepared using abrasive blast
the formation of random (crazing) cracking in the cleaning techniques or high pressure water-blasting
surface. Overwork of the finished surface could also to SA 2.5 (ISO 8501-1)
disturb the mortar bond on the concrete substrate. ▪ Reference shall be made to EN 1504-10 for specific
requirements.
ECOLOGY, HEALTH AND SAFETY
BONDING AGENT AND STEEL PROTECTION
User must read the most recent corresponding Safety
Data Sheets (SDS) before using any products. The SDS ▪ Embedded steel reinforcing should be free from
provides information and advice on the safe handling, scale, rust, oil and grease, and treated with a suitable
storage and disposal of chemical products and con- anticorrosion coating such as SikaTop® Armatec®-
tains physical, ecological, toxicological and other 110 EpoCem® or SikaEmaco®-8100 AP.
safety-related data. ▪ The application of a suitable bonding agent, such as
Sikadur®-32 LP, Sikadur® ADH 1414 or SikaTop®
Armatec®-110 EpoCem®, will improve adhesion on
large areas or where particularly dense concrete sub-
strates are involved.
Product Data Sheet
SikaEmaco® S 488 PM
September 2024, Version 02.01
020302000000002110
2/3
MIXING LOCAL RESTRICTIONS
Mix the full bag of SikaEmaco® S 488 PM with the ne-
cessary amount of cold water in a clean bucket. Add Note that as a result of specific local regulations the
the SikaEmaco® S 488 PM powder slowly to the water declared data and recommended uses for this product
while mixing continuously for at least 3 to 5 minutes may vary from country to country. Consult the local
and until a homogeneous consistency is achieved. Product Data Sheet for exact product data and uses.
SikaEmaco® S 488 PM is best mixed in a forced action
mixer. Slow speed double paddle drill can be also used LEGAL NOTES
for mixing. Do not mix at faster rate than 500 rpm. The
obtained mix results should be very creamy, easily The information, and, in particular, the recommenda-
spreadable and thixotropic. tions relating to the application and end-use of Sika
Note: Always start with minimum recommended quantity of products, are given in good faith based on Sika's cur-
water (water/powder ratio), only if required, gradually add rent knowledge and experience of the products when
water to desired consistency. Do not exceed maximum al- properly stored, handled and applied under normal
lowed limit of water per bag weight. conditions in accordance with Sika's recommenda-
tions. In practice, the differences in materials, sub-
APPLICATION strates and actual site conditions are such that no war-
ranty in respect of merchantability or of fitness for a
Apply SikaEmaco® S 488 PM while the bonding agent
particular purpose, nor any liability arising out of any
is still wet. The mortar can be applied by spatula,
legal relationship whatsoever, can be inferred either
trowel or by spray application.
from this information, or from any written recom-
For any thickness more than 50 mm, SikaEmaco® S
mendations, or from any other advice offered. The
488 PM must be applied in several layers. As soon as
user of the product must test the product’s suitability
the mortar has started to set it can be smoothed by
for the intended application and purpose. Sika re-
wooden or synthetic float. For fine surface finish
serves the right to change the properties of its
SikaEmaco® N 907 or SikaRep® Fine N can be applied
products. The proprietary rights of third parties must
over the SikaEmaco® S 488 PM.
be observed. All orders are accepted subject to our
CURING TREATMENT current terms of sale and delivery. Users must always
refer to the most recent issue of the local Product
Where ambient conditions may lead to rapid surface Data Sheet for the product concerned, copies of which
drying, the use of light water fogging, damp hessian will be supplied on request.
and polythene sheet or application of a suitable water
based curing compound from Sika® Antisol range is re-
commended. Do not commence fogging until final set
has been reached.
CLEANING OF EQUIPMENT
Clean all tools and equipment with water immediately
after use. Hardened SikaEmaco® S 488 PM can only be
removed mechanically.
Sika Gulf B.S.C. (c) Sika UAE LLC Sika Saudi Arabia Limited Sika LLC - Oman
Tel: +973 177 38188 Sika MB Construction Chemicals LLC Sika Construction Chemicals for Master Builders Solutions LLC
Email: [email protected] Sika International Chemicals LLC Manufacturing LLC (part of Sika)
Sika Kuwait Cons. Mat. & Paints Co WLL Tel: +971 4 439 8200 Riyadh / Jeddah / Dammam / Rabigh Tel. +968 22 826 500
Tel: +965 22 282 296 Email: [email protected] Tel: +966 12 692 7079 Email: [email protected]
Email: [email protected] Web: gcc.sika.com Email: [email protected] Web: gcc.sika.com
Web: gcc.sika.com Web: gcc.sika.com
SikaEmacoS488PM-en-AE-(09-2024)-2-1.pdf
Product Data Sheet
SikaEmaco® S 488 PM
September 2024, Version 02.01
020302000000002110
3/3
