DEPARTMENT OF ELECTRICAL & ELECTRONICS ENGINEERING
ME 268: Mechanical Engineering Fundamentals Seasonal
Experiment no. : 04
Part -A
Name of the Experiment: Mechanical drilling Practice
Objective:
01) To learn how to mark of plain parts, locate centers, and centre- punch.
02) To know how to set up, adjust and use vertical drilling machines.
03) To know how to drill with a bench drilling machine.
04) To practice countersinking, counter boring, hole – truing and reaming technique.
05) To learn how to prepare a drilling machine for doing a appropriate job and clamp work pieces to
the machine table.
OBJECTIVE OF MANUFACTURING:
Drawing attached.
Portable Drill Machine
Drill is a tool fitted with a cutting tool attachment or driving tool attachment, usually a drill bit or driver
bit used for boring holes in various materials or fastening various materials together with the use of
fasteners. The attachment is gripped by a chuck at one end of the drill and rotated while pressed against
the target material. The tip, and sometimes edges, of the cutting tool does the work of cutting into the
target material.
Portable Drill Machine
A grinding machine, often shortened to grinder, is any of various power tools or machine tools used
for grinding, which is a type of machining using an abrasive wheel as the cutting tool. Each grain of
abrasive on the wheel's surface cuts a small chip from the work piece via shear deformation.
Vertical Drill Machine
A drill press (also known as a pedestal drill, pillar drill, or bench drill) is a fixed style of drill that may be
mounted on a stand or bolted to the floor or workbench. Portable models with a magnetic base grip the
steel work pieces they drill. A drill press consists of a base, column (or pillar), table, spindle (or quill),
and drill head, usually driven by an induction motor.
EQUIPMENT AND ISTRUMENTS:
Bench drill machine, vice, drills of different sizes, reamer of required size, taps and counter
boring and countersinking instruments.
DEPARTMENT OF ELECTRICAL & ELECTRONICS ENGINEERING
ME 268: Mechanical Engineering Fundamentals Seasonal
WORKING PROCEDURE:
01) Study the different types of drilling machine. 2
02) Practice the job by following the operation instruction sheet.
Operation Instruction sheet
Part name Drg . No Material Job No.4
Clamping block M-0334 Mild steel Exp.4
Op.no. Operation Machine Tools Cutting Speed Feed Depth No.of
Instruction speed Rpm mm of cut cut.
M/min mm
10. Layout the 1st Layout Scriber &
block Table punch
20. Clamp the two C-clamp C-clamp
block
30. Drill Ø10.52 Bench Drill Ø 10.5 25 750 By Hand
holes drill
40. Open the blocks
50. Drill the holes in Bench Drill Ø 12.5 25 625 By Hand
1st block Drill
60. Counter Bore the Bench Counter Drill 25 400 By Hand
holes Drill Ø 20.0
70. Tap the holes 2nd Bench Tap set M12
block Drill
80. Clamp the block M12 Bolt
again
90. Drill the holes Ø Bench Drill
6; Ø 8; Ø 10& Ø Drill
Ø6 25 1300 BY Hand
15.
Ø8 25 100 By Hand
Ø 10 25 750 By Hand
Ø 15 25 500 By Hand
110. Drill Ø Bench Drill Ø 11.5 25 700 By Hand
11.5*25;Two Drill
DEPARTMENT OF ELECTRICAL & ELECTRONICS ENGINEERING
ME 268: Mechanical Engineering Fundamentals Seasonal
holes
120. Ream the above Bench Reamer Ø 150 By hand
two holes to the Drill 12H7
depth of 22
130. Unload the block
140. Counter sink the Bench Counter sink
hole Ø 10 Drill Drill Ø 1060°
150. Inspection Vernier
Caliper
Picture: Deferent parts Name of Bench Drill Machine
