PREMIUM FUEL REQUIRED

2011+ 5.0L Mustang Phase 2 ROUSHcharger Kit

P/N: 421390 (1313-P2CAL)

Installation Instructions

Application:
2011+ Ford Mustang GT with 5.0L 4-Valve Engine w/ Manual Transmission
2011+ Ford Mustang GT with 5.0L 4-Valve Engine w/ Automatic Transmission

Important Notes:
 Before installing your Mustang ROUSHcharger Kit, please read the installation manual and
verify that all items are present. . If you are missing hardware or have any questions, please
contact ROUSH Performance at 1-(800) 59-ROUSH.
 Premium fuel (91 octane or higher) is required to prevent “spark-knock” or detonation under
certain operating conditions.
 The use of fuel additives (i.e. octane boosters) is not recommended. There is a possibility
that these chemicals can damage your engine and cause drivability issues with your vehicle.

 Operating your engine without the Roush PCM recalibration will result in engine damage or
failure and will void your warranty.

 Installation of this kit voids the 3 yr / 36,000 mile limited ROUSH Powertrain warranty.

1313-P2CALIM-GC 20220929 Page 1 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

TABLE OF CONTENTS
PACKING LIST FOR 421390 (1313-P2CAL) ROUSHcharger KIT .......................................................... 3
EQUIPMENT AND SUPPLIES REQUIRED .............................................................................................. 7
GLOSSARY OF TERMS ............................................................................................................................. 8
INFORMATION ABOUT THE SUPERCHARGER BYPASS OPERATION ........................................... 8
LIMIT OF LIABILITY STATEMENT ........................................................................................................ 9
SAFETY PRECAUTIONS ........................................................................................................................... 9
SECTION A – DISASSEMBLY ................................................................................................................ 10
SECTION B – MODIFICATIONS............................................................................................................. 23
Brake Booster Hose Modification- (Manual Transmission) ................................................................... 23
Brake Booster Hose Modification- (Automatic Transmission) .............................................................. 24
Front Cover Modification ....................................................................................................................... 26
TPS/ETC Wiring ..................................................................................................................................... 30
Canister Purge Valve Wiring .................................................................................................................. 33
Intercooler Pump Wiring ........................................................................................................................ 35
Air Charge Temperature (ACT) Wiring ................................................................................................. 37
Mass Air Flow (MAF) Wiring ................................................................................................................ 39
Knock Sensor Orientation Adjustment ................................................................................................... 41
Changing the Factory Spark Plugs .......................................................................................................... 41
SECTION C – SUBASSEMBLY ............................................................................................................... 42
Intercooler Low Temperature Radiator (LTR) ....................................................................................... 42
Intake Manifold Build Up ....................................................................................................................... 45
Throttle Body Spacer Assembly ............................................................................................................. 46
Fuel Rail Assembly ................................................................................................................................. 49
Airbox Assembly .................................................................................................................................... 50
SECTION D – INSTALLATION ............................................................................................................... 54
Intercooler Reservoir Mounting .............................................................................................................. 54
Automatic Transmission Oil Cooler Hose .............................................................................................. 55
Intercooler Radiator Assembly Mounting............................................................................................... 58
Electric Water Pump, Mounting Bracket and Hoses .............................................................................. 59
Induction Resonance Tube Delete Grommet .......................................................................................... 64
Intake Manifold and Supercharger Installation ....................................................................................... 65
FEAD Assembly ..................................................................................................................................... 72
Coolant Hoses ......................................................................................................................................... 72
Air Induction System .............................................................................................................................. 81
SECTION E- Final Assembly ..................................................................................................................... 85
PCM Flashing ......................................................................................................................................... 88
APPENDIX A – SIDE SHIELD MODIFICATIONS ................................................................................ 88
1313-P2CALIM-GC 20220929 Page 2 of 90 1-800-59-ROUSH
 PREMIUM FUEL REQUIRED

PACKING LIST FOR 421390 (1313-P2CAL) ROUSHCHARGER KIT

Part Ref Description Part Number Qty

Air Induction ---
1 ROUSH Airbox Assembly 1313-9643 1
2 MAF Tube R07060101 1
3 Air Filter 997-495 1
4 Clean Air Tube Asy 1313-9B659 1

Part Ref Description Part Number Qty

Hardware Kit A – Induction 1313CAK-HWKA 1
5 Hose Clamp R07130014 1
6 Hose Clamp R07130015 1
7 Edge Seal 39-211-12 1
8 Edge seal (9.5”) R07130026-13-9.5 1
9 Edge seal (12”) R07130026-13-12 1
10 Edge seal (4”) R07130026-13-4 2
11 Mounting Bracket – MAF Tube to Air Box R07130010 1
12 Bolts M6x1.0x14 – Mntg Brkt to MAF & Airbox N605771 3
13 Vacuum Fitting – S/C Bypass 383004-S 1
14 Vacuum Fitting – Brake Booster (3/8 x 3/8) P2233A 1
15 Vacuum Cap – 3/8 CS2575 1
16 Nut – M6x1.0 Airbox to Fan Shroud W520412 1
17 MAF Bolts (M4x0.7x10 Torx) R07130007 2

Part Ref Description Part Number Qty

18 Fuel Charging Assembly 13119H487 1
19 Supercharger Assembly 1311H-6F066 1
20 Fuel Rail 13119F792 1
21 Throttle Body Assembly – Dual 60 mm R07060150 1
22 Throttle Body Spacer Assembly 13119A589 1
23 Fuel Injector Kit M-9593-LU47RSH 1
24 Fuel Injector Clip 1311-9C995 8
25 S/C Pulley – 6K Ø85mm 1313-6K85 1
26 Spark Plug - 0.9mm gap (CYFS12YP) BL3E-12405-BA 8

1313-P2CALIM-GC 20220929 Page 3 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

Part Ref Description Part Number Qty

Hardware Kit B – Fuel Charging 1311-TVSHKB 1
27 Gasket – Throttle Body To Spacer R07060153 1
28 Gasket – Throttle Body Spacer to Supercharger R07060152 1
29 Bolt – Throttle Body to Spacer & Supercharger (M6 x 32.5) R18020009 8
30 Bolt – Intake to Cylinder Heads (M6 x 40) R18020004 6
31 Bolt – Supercharger to Intake (M8 x 53) N808130 10
32 Bolt – Evaporative Emission Canister Valve to Spacer (M6 x 35.5) N808429 2
33 Bolt – S/C Pulley (M6 x 16) W500013 6

Part Ref Description Part Number Qty

FEAD ---
34 Upper FEAD Bracket 13148B653U 1
35 FEAD Tensioner Bracket Assembly 13118B603 1
36 Serpentine FEAD Belt 6K2085-8620 1

Part Ref Description Part Number Qty

Hardware Kit C – FEAD 13116066FRTHKC 1
37 Pulley - Idler B/S 76mm 953045 2
38 Bolt – Idler (M8 x 28 large washer) R18020060 2
39 Bolt – Upper FEAD to Engine and Intake (M8 x 84) W704752 2
40 Bolt – Lower Bracket to Upper Bracket (M8 x 41) W705128 1
41 Bolt – Upper FEAD to Engine (Bottom) (M8x1.25x60) 111116346 3
42 Bolt – Lower Bracket to Engine (M8 x 120) N811329 2

Part Ref Description Part Number Qty

PCV & Vacuum ---
43 PCV Fresh Air Inlet 13116758 1
44 PCV Purge Hose with Bubbler 13116K817 1
45 Evaporative Emission Canister Purge Valve Line BR3V-9G271 1
46 7/32” Vacuum Hose – Supercharger Bypass (Length = 105mm) R18140001 1
47 Vacuum Harness – Supercharger Bypass Reference 7R3V-9E498 1

Part Ref Description Part Number Qty

Wiring ---
48 Electrical Jumper – Intercooler Pump 13118W501 1
49 ACT Wiring Harness 1311-12A690 1
50 TPS Extension Harness 131114A595 1
51 Canister Purge Valve Extension Harness 13119G866 1
52 MAF Extension Harness 131112B579W 1
53 Intercooler Jumper Harness (use if Pump is FS00057975) PT00045528 1

1313-P2CALIM-GC 20220929 Page 4 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

Part Ref Description Part Number Qty

Hardware Kit D – Wiring 1313-HWKD-AA
54 Nut - I/C Relay Mounting (M6) W520412 2
55 Zip Tie with Fir Tree Clip (Wire Harness to Front Cover) 156-00329 1

Part Ref Description Part Number Qty

Decals / Labels & Instructions ---
56 Decal – 2011 Belt Routing Diagram 13116E072 1
57 Decal – Premium Fuel Only (Cluster) R07110004 1
58 Decal – Premium Fuel Only (Fuel Door) 13109A095 1
59 Decal- PCM R07100008 1
60 Warranty Card 1150-TVSCALWC 1
61 Limited Base Warranty 1150-LBW 1
62 Installation Manual 1313-P2CALIM 1
63 Label – Spark Plug Warning PT00045644 2

Part Ref Description Part Number Qty

Intercooler System ---
64 Degas Bottle 13108D080 1
65 Intercooler Electric Water Pump with Bracket 392022009 1
66 Bracket - Intercooler Pump Mounting 1313-8C419 1
67 Intercooler Low Temp Radiator (LTR) 13108K229 1
68 3/4" Hose – Degas Bottle Inlet 13118D031 1
69 3/4" Hose – Intercooler Pump Inlet 13108D029 1
70 3/4" Hose – Intercooler Pump to LTR 13108K236 1
71 3/4" Hose – Intercooler LTR Outlet 13118D030 1
72 3/8" Hose – Engine Bottle Degas Hose 13118276 1
73 3/4” Hose Sleeve – 424mm Heater Hoses 1311-18K579SLV 2
74 Intercooler Pump Mounting P Clip 8863T95 1
75 Intercooler Pump Foam 1318-8D082 1
BOLT - M8 X 1.25 X 29 HEX FLANGE DOGPOINT FULLY
W500224-S437 1
76 THREADED 8.8
77 Intercooler Bracket (Only for Pump PN: FS00057995) PT00045433 1

1313-P2CALIM-GC 20220929 Page 5 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

Part Ref Description Part Number Qty

Hardware Kit E – Intercooler System 13116066FRTHKE 1
78 Bracket – LTR Upper LH 13108K242 1
79 Bracket – LTR Upper RH 13108K243 1
80 Bracket – LTR Lower LH 13108K244 1
81 Bracket – LTR Lower RH 13108K245 1
82 Rubber Grommet – LTR Isolator R07060107 4
83 Sleeve – LTR Isolator R07060108 4
84 Degas Bottle Cap 9C3Z-8101-B 1
85 Clamps – ¾” Hoses (Constant Tension) CT19x12-BO 8
86 Bolt – Long Bumper Bolts (M8 x 35) R18020007 2
87 Bolt – LTR to Brackets (4) & I/C Pump to Bracket (2) (M8 x 25) W500224 6
88 Nut – I/C Pump Mounting Bracket to Bumper Bolts (M8) W520413 4
89 Bolt – Degas Bottle Mounting & LTR Bracket to Chassis (M6 x 22) R18020057 4
90 J-Clip – Degas Bottle & Pump Bracket Mounting (M6 Short) N623332 1
91 NVH Isolator – I/C Pump to Bumper Beam 13108Z419 1
92 NVH Isolator – I/C Pump to LTR 13108Y419 1
93 Nut – I/C Wiring Relay to Chassis (M6) W520412 1

Part Ref Description Part Number Qty

HARDWARKE KIT G - Automatic Transmission 1313-HWKG-AA 1
94 Hose - Trans Cooler (26" Length) 1312-7R081 1
95 Worm Clamp - Trans Cooler Line Joint (3/4") 5407K58 1
96 Convolute/Loom - Split, black, 3/4in 1312-TRANSCONV 1
97 Zip tie - 6" LENGTH KTI--78070 7

Part Ref Description Part Number Qty

CALKIT 1311-P2CALKIT 1
98 ROUSH Diagnostic Tool Flash Manual RDT-CALIM 1
99 Optional Roush PCM Flash PCM-FLASHDOC 1
100 Flash Voucher Card P1311-P2 1

Part Ref Description Part Number Qty

101 Shield- Pulley Bearing Dust Cover PT00040547 3

1313-P2CALIM-GC 20220929 Page 6 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

If you are missing any items, please call us toll free at 1-800-59-ROUSH.

EQUIPMENT AND SUPPLIES REQUIRED

• 1/4” and 3/8” Drive Ratchets with Extensions

• Metric and Standard Socket Sets (short and deep recommended)

• Metric and Standard Wrench Sets

• 3/8” Drive Torque Wrench (7-35 ft-lb range)

• 6” Scale, Tape Measure, or Other Measuring Device

• Assembly Lubricant (White Lithium Grease or Petroleum Jelly)

• Electrical Tape

• Sharp Knife or Razor Blade

• Medium Strength Thread Locker – Loctite 242 (blue) or equivalent

• T-20 Torx Bit Screwdriver or Socket

• 5/16” Drill Bits and Drill motor

• Coolant (meeting Factory Ford specification for 2011 Mustang GT)

• 1/2” Drive Ratchet or Breaker Bar

• Short Phillips-head Screwdriver

• 5/8” Fuel Line Removal Tool

• Solder and Soldering Iron

• Heat Gun or Small Torch for Heat Shrink Tubing

• Tie Straps (Zip Ties)

• Trim Pad Tool (for pushpin removal)

1313-P2CALIM-GC 20220929 Page 7 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
• Fender Cover (2)

• 1/2” Transmission Line Removal Tool (Only for Automatic Transmission)

GLOSSARY OF TERMS
ACT Air Charge Temperature Sensor (From the factory, this function is integrated into the
MAF sensor. With this kit, a separate ACT sensor is installed into the intake
manifold)

ETC Electronic Throttle Control

MAFS Mass Air Flow Sensor

PCM Powertrain Control Module (a.k.a. ECM, ECU, PCU, EEC)

PCV Positive Crankcase Ventilation

RDT ROUSH Diagnostic Tool

TPS Throttle Position Sensor

VMV Vapor Management Valve (aka Canister Purge Valve)

Breakout Point A place in an electrical harness where the wiring for an individual component leaves
(breaks out of) the main harness to attach to an individual component.

INFORMATION ABOUT THE SUPERCHARGER BYPASS OPERATION

There is a great deal of misinformation about the function of supercharger bypass systems. The
supercharger is a positive-displacement pump; that is, so long as it is rotating, it is always pumping air.
During low demand or high vacuum operation (i.e. idle, deceleration, and light throttle cruise), the
pumping action is undesirable as it creates unwanted heat and noise. The bypass circuit, when open,
prevents any pressure buildup across the supercharger and allows air to circulate through the rotors,
allowing the supercharger to “idle” freely during these conditions. This results in reduced noise, and by
reducing heat buildup in the intake, significantly improves street and strip performance. As throttle
demand increases, the bypass circuit is closed, resulting in full performance from the supercharger. The
bypass circuit is never used to limit or control boost during full-throttle operation and defeating or altering
the bypass function will not result in improved performance in any condition, and will result in poor
drivability.

1313-P2CALIM-GC 20220929 Page 8 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

LIMIT OF LIABILITY STATEMENT

The information contained in this publication was accurate and in effect at the time the publication was
approved for printing and is subject to change without notice or liability. Roush Performance Products
reserves the right to revise the information presented herein or to discontinue the production of parts
described at any time. Installation of this kit voids the 3 yr / 36,000 mile ROUSH Powertrain warranty.

SAFETY PRECAUTIONS

STOP! CAREFULLY READ THE IMPORTANT SAFETY PRECAUTIONS AND WARNINGS

BEFORE PROCEEDING WITH THE INSTALLATION!

Appropriate disassembly, assembly methods and procedures are essential to ensure the personal safety
of the individual performing the kit installation. Improper installation due to the failure to correctly follow
these instructions could cause personal injury or death. Read each step of the installation manual
carefully before starting the installation.

 Always wear safety glasses for eye protection.

 Place the ignition switch in the OFF position.

 Always apply the parking brake when working on the vehicle.

 Block the front and rear tire surfaces to prevent unexpected vehicle movement.

 Operate the engine only in well-ventilated areas to avoid exposure to carbon monoxide.

 Do not smoke or use flammable items near or around the fuel system.

 Use chemicals and cleaners only in well-ventilated areas.

 Batteries can produce explosive hydrogen gas which can cause personal injury. Do not
allow flames, sparks or flammable sources to come near the battery.

 Keep hands and any other objects away from the radiator fan blades.

 Keep yourself and your clothing away from moving parts when the engine is running.

 Do not wear loose clothing or jewelry that can be caught in rotating or moving parts.

1313-P2CALIM-GC 20220929 Page 9 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

SECTION A – DISASSEMBLY
The following section will guide you through the disassembly of the stock components. Special care
should be taken to label fasteners and parts that are taken off during this procedure since many will be
reused:

1. Cover both fenders with fender covers to protect the vehicle finish.
2. Release the fuel system pressure (NOTE: The following procedure is taken directly from the Ford
Service Manual).

WARNING: Fuel in the fuel system remains under high pressure even when the
engine is not running. Before working on or disconnecting any of the fuel lines or fuel
system components, the fuel system pressure must be relieved. Failure to do so can
result in personal injury.

WARNING: Do not smoke or carry lighted tobacco or open flame of any type when
working on or near any fuel-related components. Highly flammable mixtures are always
present and can be ignited, resulting in personal injury.
a. Disconnect the Fuel Pump Control Module electrical connector.
NOTE: The Fuel Pump Control Module is located in the spare tire stowage compartment.

b. Start the engine and allow it to idle until it stalls.

c. After the engine stalls, crank the engine for approximately 10 seconds to make sure the
fuel injector supply manifold pressure has been released.

d. Turn the ignition switch to the OFF position.

1313-P2CALIM-GC 20220929 Page 10 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
3. Using an 8mm wrench, disconnect the (-) negative and (+) positive connections to the battery.

4. Remove the (8) push pin retainers by pulling the center pin and remove the radiator trim cover.

Before continuing, refer to the CALKIT included with your ROUSHcharger kit.
Determine the PCM flash method you will be using. If performing the PCM flash
yourself or at a preferred ROUSH dealer, proceed to step 6. If sending the PCM to
ROUSH for a ROUSH performed PCM flash, continue with step 5.

5. Disconnect the 3 PCM (Powertrain Control Module) connectors by lifting the grey levers over the
connector back shell and lifting the connectors from their sockets. Remove the PCM by removing
two 10mm bolts and pulling the PCM forward and lifting out of the engine compartment. Follow
the instructions on the next page as soon as possible to help minimize the amount of time you are
without a PCM.

Connector
Locations
Retaining Bolts

Important: Be sure to write your VIN number and phone number (in case we need to contact you
for additional vehicle information) on the PCM using a permanent marker.

1313-P2CALIM-GC 20220929 Page 11 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
INSTRUCTIONS FOR RETURNING THE PCM TO ROUSH FOR CALIBRATION
Outlined below are the instructions for returning your stock powertrain control module (PCM) to Roush
Performance Products so we can install our calibration to make the engine run properly with the new
components. Please complete the “Base Limited Warranty Registration” card and include it,
along with the PCM, the “Optional Roush PCM Flash” request document, and the “Voucher
Card”. Once we receive your PCM, we will reprogram and return it back to you the same day for next-
day delivery. Operating your engine without our calibration will result in engine damage or failure
and will void all warranty.

Note: It is important to reinstall the PCM in the vehicle it came from to prevent setting a
trouble code and having to relearn the anti-theft code which can only be performed using
specialized Ford Service Bay tools.
• If you haven’t already done so, write your vehicle identification number (VIN) and phone number
on the PCM using a permanent marker.

• Using bubble wrap, or another appropriate packing material, wrap and package the PCM to help
prevent it from being damaged during shipping.

• Place the wrapped PCM in an appropriate shipping box.

• Complete the “Warranty Registration Card” (1150-TVSCALWC),

• Complete the “Optional ROUSH PCM Flash” request document (PCM-FLASHDOC) and
attach the flash “Voucher Card” (P1311-P2) to the document.

• Include the “Warranty Registration Card”, “Optional ROUSH PCM Flash” document, and
the “Voucher Card” in the shipping box, along with the PCM.

• Ship the PCM and contents to:

Roush Performance
ATTN: PCM FLASH
12170 Globe Street
Livonia, MI 48150

Upon receipt of the PCM, a customer service representative will contact you to arrange payment.
Once you receive your ROUSH flashed PCM, reverse step 5 for PCM installation.

1313-P2CALIM-GC 20220929 Page 12 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
6. Raise the front of the vehicle using the Ford recommended lifting points and place onto safety
stands. With the tires lifted off of the ground, remove the front wheels. Remove the (3) forward
Phillips-head screws from each front wheel liner. Using a Phillips-head screwdriver, turn the (5)
inner fender push pins ¼ turn to release the centers. Remove the pushpins and then remove the
forward inner fenders.

7. Remove the (3) lower close-out to radiator support screws (7mm socket). Remove the (2) upper
bumper cover screws near the headlights (10mm socket). Remove the (4) front fender to bumper
cover nuts inside the forward wheel well (10mm socket). Reach inside the front wheel wells and
unplug the front turn signals. Lift the front bumper cover slightly and pull partially off of the
vehicle. Unplug the fog lights and set the front bumper cover aside.

8. Remove the (4) push pins that retain the impact absorber to the front bumper beam and set the
absorber aside.

9. Carefully remove the radiator / cooling module side shields that are mounted to the left and right
hand side of the A/C Condenser. (See Appendix A) Note: The LH shield engages the air inlet
system.

10. With the engine cool, remove the cap on the engine coolant degas bottle and drain the coolant
using the petcock located on the lower passenger side of the radiator.

TIP: Connect a 3/8” hose to the drain fitting next to the petcock and run into a clean drain pan or
bottle. Use a ¾” wrench to open petcock and allow coolant to drain out of the fitting.

Drain Petcock

1313-P2CALIM-GC 20220929 Page 13 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
11. If equipped, remove the (4) nuts and the strut tower cross brace. Reinstall the (4) nuts and
torque to 30-40 Nm. The strut tower cross brace cannot be reused after the supercharger has
been installed.

12. Remove the engine appearance cover. The cover cannot be reused after the supercharger
has been installed.

1313-P2CALIM-GC 20220929 Page 14 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
13. Remove the M6 bolt that secures the induction resonance tube to the driver side fender near
the cowl. Remove the tube from the cowl.

Remove

14. Disconnect the PCV Fresh Air Inlet tube from the left-hand cam cover and clean air tube.
Remove the clean air tube from the throttle body and airbox. Remove the clean air tube and
the induction resonance tube from the vehicle. Neither of these components will be reused.

15. Remove the MAF (mass air flow) sensor connector by pulling the red locking tab back and
pressing the black release tab. Release the locking tabs securing the upper airbox lid to the
lower airbox. Disconnect the MAF wiring harness retainer from the front edge of the upper
airbox lid and remove the lid from the vehicle. The airbox lid will not be reused.

Release Tabs

Harness Retainer Location

Disconnect MAF Connector

1313-P2CALIM-GC 20220929 Page 15 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
16. Disconnect the throttle body electrical connector. (Pull the red locking tab back; press the black
release tab to disengage the lock). Refer to #15 in figure shown below.

17. Disconnect the VMV (evaporative emission canister purge valve) tube and electrical connector.
Remove the VMV tube retainer from the front left hand cam cover. Disconnect the remainder
of the tube at the fitting located behind the inner fender below the brake booster. This tube will
not be reused. Refer to #16 in figure shown below.

18. Remove the PCV Purge line from the intake manifold and right-hand cam cover. This line will
not be reused. Refer to #17 in figure shown below.

Procedures #15 - 17

19. Disconnect the fuel supply hose from the fuel rail. Refer to #18 in figure shown below.

20. Disconnect the brake booster vacuum hose from the intake manifold. This port is located
directly behind the throttle body. Refer to #19 in figure shown below.

1313-P2CALIM-GC 20220929 Page 16 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
20-a.Disconnect the brake booster vacuum hose and aspirator assembly from the vehicle and
set aside. (Auto Trans Only)

Brake Vacuum Hose and Aspirator Assembly

1313-P2CALIM-GC 20220929 Page 17 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
21. Disconnect the heater feed and return hoses located at the front of both the LH and RH
cylinder head intake flanges. Position these hoses aside by tucking them up underneath the
edge of the hood near the windshield wipers. Refer to #20 in figure shown below.

22. Remove the (2) nuts and support bracket that retained the RH heater hose above the RH fuel
rail. This hardware will not be reused. Refer to #21 in figure shown below.

23. Remove the steel section of the brake booster vacuum line from the rubber hose at the joint
found at the rear of the intake manifold. Discard the steel and forward rubber section of this
assembly as it will not be reused. Refer to #22 in figure shown below.

24. Remove the (2) nuts and support bracket that retained the LH heater hose above the LH fuel
rail. This hardware will not be reused. Refer to #23 in figure shown below.

Procedures #18 - 23

25. Remove the 3/8” engine coolant degas hose from both the engine and the degas bottle.

26. Carefully detach the (4) wiring harness retainers from the rear of the intake manifold. The two
“outer” clips will be reused once the new manifold is installed to retain the harness.

27. Remove and discard the LH and RH fuel rail insulators. Disconnect the (8) fuel injector
electrical connectors.

28. Remove the (4) fuel rail bolts. These bolts will be reused. NOTE: It is not necessary to
remove the fuel rail from the intake manifold assembly.
1313-P2CALIM-GC 20220929 Page 18 of 90 1-800-59-ROUSH
 PREMIUM FUEL REQUIRED

29. Remove the (6) intake manifold mounting bolts and remove the intake manifold and fuel rail
assembly from the vehicle. This hardware will not be reused.

Procedures #26 – 28

30. Clean the intake mounting surfaces and apply tape over the open intake ports to prevent
engine contamination.

31. Remove the engine coolant degas bottle.

1313-P2CALIM-GC 20220929 Page 19 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
32. Remove the Front End Accessory Drive (FEAD) belt. Rotate the FEAD Tensioner counter-
clockwise to release the belt tension and remove the belt.

33. Remove the (4) bolts securing the Water Pump Pulley to the engine

34. Cut and remove the A/C compressor belt. Discard belt.

35. Remove the upper radiator hose.

36. Remove the electric fan and shroud assembly from the vehicle.

1313-P2CALIM-GC 20220929 Page 20 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
37. Disconnect and remove the transmission oil cooler lines support bracket from the cooling fan
module. Un-crimp the bracket from the transmission cooler lines and discard the bracket and
isolator. Disconnect the transmission oil cooler line at the quick connect fitting. Use the ½”
transmission line connector removal tool.

Disconnect line

Uncrimp
remove

38. Remove the four fasteners holding the AC condenser to the cooling module and shift the AC
condenser forward and down. Do not disconnect any AC lines

1313-P2CALIM-GC 20220929 Page 21 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
39. Disconnect the transmission cooler hose from the transmission oil cooler. Remove the hose
clamp for reuse.

Disconnect

40. Unclip the engine electrical harness retention clips that retain the engine harness to the top
corners of the right hand (passenger side) front cover.

1313-P2CALIM-GC 20220929 Page 22 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

SECTION B – MODIFICATIONS
The following section will guide you through the required modifications of existing components and build
up of the assemblies used to complete the installation. With the exception of the wiring modifications
and intercooler pump bracket mounting, all of this work can be performed away from the vehicle.
BRAKE BOOSTER HOSE MODIFICATION- (MANUAL TRANSMISSION)

1. Remove the factory brake booster hose that is still connected to the booster.

2. Cut 30mm off of the end of the hose that was connected to the brake booster and 40 mm off of
the opposite end that was connected to the steel tube, as shown below. Place a piece of tape or
a mark on the end of the hose that was cut by 30mm. This end of the hose will connect to the
throttle body spacer upon re-assembly.

40
30

1313-P2CALIM-GC 20220929 Page 23 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
BRAKE BOOSTER HOSE MODIFICATION- (AUTOMATIC TRANSMISSION)

1. Retrieve the brake vacuum hose and aspirator assembly and place it on a work bench.
2. Disassemble the vacuum hose assembly and lay it out on the bench as shown.

Clamp 2 Clamp 4

Discard this hose

Hose 2
Hose 1
Clamp 3
Clamp 1
Discard
Hose 3

Clamp 5

3. Remove convolute and discard. Modify Hose 1 as shown.

Hose 1
Remove Cut

30 mm

Hose 1A

1313-P2CALIM-GC 20220929 Page 24 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
4. Modify Hose 2 as shown.

Hose 2
Hose 2A

End
“A”
40 mm

Brake Vacuum Hose and Aspirator Assembly

Attach End “A” of Hose 2A to the aspirator assembly as shown. Attach Hose 1A as shown.

Clamp 4
New Clamp End
Clamp 2 7329K13 “A”

Hose 1A Hose 2A

Clamp 3

Clamp 5
Hose 3

1313-P2CALIM-GC 20220929 Page 25 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
FRONT COVER MODIFICATION

1. Using a grinder or cut off wheel, modify the front cover in the areas shown. The two bosses
located at A and B need to be reduced in height such that they are flush, or lower than the height
of the nearby rib structure. The portions of the rib structure C, D, E and F need to be removed
completely (cut just above flush to the surface of the front cover). Be careful not to remove too
much material in these areas as permanent damage to the front cover could occur. The boss
located at G needs to be reduced in height and cut in half.

D
C

1313-P2CALIM-GC 20220929 Page 26 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

A CROSS HATCHED
SURFACES ‘A’ and ‘B’,
MUST BE LOWER
THAN OR EQUAL TO
THIS RIB HEIGHT

1313-P2CALIM-GC 20220929 Page 27 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

REMOVE MATERIAL
OFF OF BOSS ‘G’ UNTIL
THE 20mm HEIGHT IS
ACHIEVED.

1313-P2CALIM-GC 20220929 Page 28 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

REMOVE MATERIAL IN
THESE AREAS UNTIL THEY
C ARE FLUSH WITH THE
FRONT COVER SURFACE.

D
F

1313-P2CALIM-GC 20220929 Page 29 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
TPS/ETC WIRING

1. If you have not already done so, remove the upper radiator cover by removing the 8 push pins.

2. NOTE: IF THE WIRE HARNESS INCLUDED IN THE KIT IS 131114A595-BA SKIP STEPS 2-4
DO NOT DEPIN NOT NECESSARY!”
Locate the Throttle Position Sensor (TPS) connector and harness at the front of the passenger
side cylinder head. Use a proper de-pinning tool to remove the connector from the harness.

1313-P2CALIM-GC 20220929 Page 30 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
3. Depress the locking tab and separate the “empty” female 1 x 6 connector from the new TPS/ETC
Extension harness (131114A595). It will be used in the next step.

4. Populate the new connector such that the yellow with violet wire is in position 1, the blue with
green wire is in position 2, the brown wire is in position 3, the blue with orange wire is in position
4, the yellow wire is in position 5 and the green with violet wire is in position 6. Install the red
plastic lock into the connector to secure the wires in place.

1313-P2CALIM-GC 20220929 Page 31 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
5. Connect the TPS/ETC extension harness to the newly installed connector. The wire colors on
each side of the connector pair should align. Route the harness along the main wiring harness to
the rear of the driver side cam cover. Use tape or zip ties to secure the extension harness to the
main harness.

1313-P2CALIM-GC 20220929 Page 32 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
CANISTER PURGE VALVE WIRING

1. Locate the Canister Purge Valve electrical connector at the front of the passenger side cylinder
head. Remove and discard the 90 degree wire retainer. Use a proper de-pinning tool to remove
the connector from the harness.

Discard retainer

1313-P2CALIM-GC 20220929 Page 33 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
2. Depress the locking tab and separate the “empty” female 1 x 2 connector from the Canister
Purge Valve Extension harness (13119G866). This connector replaces the connector removed in
the previous step. Carefully pull the white locking tab forward to allow wires to be installed
into the connector. Populate the new connector such that the white with brown wire is in
position 1 and the green wire is in position 2. Depress the white locking tab to secure the wires.

3. Connect the Canister Purge Valve Extension harness to the newly installed connector. The wire
colors on each side of the connector pair should align. Route the harness along the main wiring
harness to the rear of the driver side cam cover. Use tape or zip ties to secure the extension
harness to the main harness.

1313-P2CALIM-GC 20220929 Page 34 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
INTERCOOLER PUMP WIRING

1. Locate the stud next to the underhood fuse box near the passenger side headlight. Remove the
wiring harness from this stud. The harness will be re-attached to this stud in a later step.

2. Install the relay from the Intercooler Pump Wiring Harness (13118W501) onto the stud. Install
the fuse on top of the relay onto the same stud. Use (1) M6 nut (W520412) from the Intercooler
Hardware Kit (13116066FRTHKE) to secure the relay and fuse to the stud. Torque the nut to 8-
12 Nm. Reinstall the wiring harness from previous step to the stud for proper retention.

1313-P2CALIM-GC 20220929 Page 35 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
3. Route the red wire (part of the Intercooler Pump Wiring Harness installed above) to the positive
post at the rear of the fuse block. Remove the nut from the positive post and install the red wire
eyelet. Reinstall the nut onto post. Torque to 8-12 Nm.

4. Route the other bundle of wires coming from the relay around the front of the fuse box along the
factory forward lamp harness. Remove (1) bolt securing the factory ground wires to the chassis
behind the headlight. Replace the bolt to secure the factory grounds including the grounding
eyelet from with the intercooler pump harness.

5. Route the single wire with two electrical connectors along the factory engine harness to the rear
of the passenger side cylinder head. Connect these two connectors in-line with the passenger
side radio capacitor. The single connector will be routed to the intercooler pump in Section D of
this manual.
1313-P2CALIM-GC 20220929 Page 36 of 90 1-800-59-ROUSH
 PREMIUM FUEL REQUIRED
AIR CHARGE TEMPERATURE (ACT) WIRING

1. Unplug the 3 PCM connectors by pushing the gray connector lock arms towards the front of the
vehicle. You will be working with the bottom 70 pin or "cowl" connector only.

2. a) Remove the pin locking device as shown in figures 2 and 3. Also remove the wire support on
the back of the connector (figure 5) by removing the tape and using a small screwdriver to lift the
locking tabs.

3. The ACT sensor loom (1311-12A690) will have the ACT sensor connector at one end. On the
other end will be 2 wires, one with a blunt end and the other with a pin already crimped on. The
blunt wire will be spliced into the wire located in pin C-56 of the cowl connector. The wire with the
pin will be inserted into location C-36 of the cowl connector. There are small numbers on the back
of the connector noting location. Figure 4 below will also help to identify the pin locations.

Figure 4: PCM Pin Locations for Cowl

Connector – Front View (side that connects to
PCM)

1313-P2CALIM-GC 20220929 Page 37 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
b) Remove pin C-56 from the connector by gently moving the locking tab away from the pin on
the front of the connector and pulling the wire out of the back of the connector. Remove the
insulation from a 1/2" section of the pin C-56 wire and 1/2" of the end of the blunt wire on the ACT
loom. Solder the two wires together and seal them with the supplied shrink wrap. Reinsert the
spliced wire into the C-56 location. Note the orientation of the pins on the front of the connector
and reinstall the pin in the same way. If the pin is turned it will not lock. The finished/inserted
splice is shown in figures 5 and 6 (green wire with black shrink wrap).

c) Insert the ACT loom wire with the pin into the empty C-36 location of the connector. The back
of the connector may have a blank cover at the C-36 location. Carefully push this blank cover in
with a small screw driver or punch to allow you to insert the pin. Note the orientation of the pins
on the front of the connector and install the new pin in the same way.

Figure 5 Figure 6

4. a) Reinstall the pin locking device by snapping it into place. Reinstall the wire support on the
back of the connector and wrap with tape as before.
b) Reconnect the PCM connectors and route the ACT loom wire along the top of the cylinder
head as shown in figure 7.

Figure 7

1313-P2CALIM-GC 20220929 Page 38 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
MASS AIR FLOW (MAF) WIRING

1. Locate the MAF wire harness connector and de-pin the factory MAF connector using a proper de-
pinning tool. Remove the pin locking device from the front face of the connector and remove the
connector from the harness, retain the pins crimped to each wire as shown.

2. Insert the pins from the factory connector into the female connector provided on the end of the
MAF Extension Harness (131112B579W). The following color wires go into the following
positions on the clip: Violet with Grey – position #2, Grey with Yellow – position #3, Blue with
White – position #4, and Yellow with Violet – position #5. NOTE- Positions 1 and 6 are not used.

3. Perform a visual inspection of the newly pinned connector to ensure that wire colors match on both
sides of the harness. Re-install the pin locking device on the front face of the connector.

1313-P2CALIM-GC 20220929 Page 39 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
4. Locate the MAF Extension harness (1311-12B579W). Remove one of the two push pins on the
harness and remove the electrical tape. Move the push pin about halfway on connector. Use
electrical tape to secure to harness.

5. Connect the new MAF extension harness to the new connector and route the MAF extension
harness around the outer perimeter of the lower air box.

1313-P2CALIM-GC 20220929 Page 40 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
KNOCK SENSOR ORIENTATION ADJUSTMENT

1. Loosen the two bolts which retain the knock sensors to the engine block and rotate the RH and
LH knock sensor toward the RH and LH cylinder heads respectively. In order to do so, first
remove the 90 degree plastic wiring retainer clipped to the connector and taped to the wiring
convolute. Torque the knock sensor bolts to 20-30Nm.

Remove Clips Here

CHANGING THE FACTORY SPARK PLUGS

1. Disconnect the electrical connectors for each ignition coil (8 places) and remove the fastener
holding the coil on plug in place. Remove the ignition coil on plug. A slight twisting motion will
break the seal and ease removal. Remove the factory spark plugs (8 places) and set aside.
These will not be re-used.

2. Install the eight (8) provided spark plugs (CYFS12YP) which are gapped to 0.9 mm. Torque to
14 Nm (124 lb-in). Install the ignition coil on plugs. Apply a small amount of dielectric grease to
the inside of the coil on plug boots before attaching to the spark plugs. Torque the bolts to 6 Nm
(53 lb-in). Re-install the coil on plug covers.

3. Locate two (2) spark plug warning labels (PT00045644, found in 1121-HWKF). Place 1 label on
cylinder 1 and cylinder 5 coils (front coil of RH and LH cam cover).

1313-P2CALIM-GC 20220929 Page 41 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

SECTION C – SUBASSEMBLY
INTERCOOLER LOW TEMPERATURE RADIATOR (LTR)

1. Insert (1) Rubber Grommet (R07060107) found in Hardware Kit E (13116066FRTHKE) into each
mounting tab on the Low Temp Radiator LTR (13108K229).

Upper RH Upper LH

Lower RH
Lower LH

2. Push (1) Sleeve (R07060108) found in Hardware Kit E (13116066FRTHKE) into each of the
rubber grommets previously installed.

1313-P2CALIM-GC 20220929 Page 42 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

3. Mount the Upper LH LTR Bracket (13108K242) to the upper LH corner of the LTR using (1) M8 x
1.25 x 25mm bolt (W500224). These can be found in Hardware Kit E (13116066FRTHKE). Align
the edges of the bracket such that they are flush with the mounting tab on the LTR. Torque bolt to
20-30 Nm.

Upper LH Corner

4. Repeat step 3 for each of the remaining LTR Brackets. 13108K243 will go to the upper RH
corner, 13108K244 to the lower LH corner and 13108K245 to the lower RH corner of the LTR.
These can be found in Hardware Kit E (13116066FRTHKE).

Upper RH Corner Lower LH Corner

Lower RH Corner
1313-P2CALIM-GC 20220929 Page 43 of 90 1-800-59-ROUSH
 PREMIUM FUEL REQUIRED

5. Install the Intercooler Pump to LTR NVH Isolator (13108Y419) on the front face of the LTR. The
pad should be stuck to the LTR so that it is 170mm from the top and 140mm from the right side.

170 mm

140 mm

1313-P2CALIM-GC 20220929 Page 44 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

INTAKE MANIFOLD BUILD UP

1. Remove Fuel Charging Assembly (13119H487) from the packaging.

2. Attach the rubber hose from the PCV Purge Hose (13116K817) to the bubbler fitting (3/8” barb)
on the bottom of the fuel charging assembly and secure it with the supplied clamp.

Install clamp in
this location

1313-P2CALIM-GC 20220929 Page 45 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
THROTTLE BODY SPACER ASSEMBLY

1. Remove the Evaporative Emission Canister Purge Valve from the stock intake manifold.

2. Install the valve into the new Throttle Body Spacer using (2) M6 x 1.0 x 35.5 mm bolts (N808429)
found in Hardware Kit B (1311-TVSHKB). Torque bolts to 8-12 Nm.

1313-P2CALIM-GC 20220929 Page 46 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
3. Connect the supercharger boost bypass actuator hose (R18140001) to the throttle spacer.

4A. (MANUAL TRANS. ONLY) Connect the marked end of the modified brake booster hose to the
throttle spacer.

1313-P2CALIM-GC 20220929 Page 47 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
4B. (AUTO TRANS ONLY) Using the finished brake vacuum aspirator assembly from Section C –
Subassembly, install the end of hose 2A to the fitting on the throttle body spacer. Secure the hose
with Clamp 4.

1313-P2CALIM-GC 20220929 Page 48 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
FUEL RAIL ASSEMBLY

1. Carefully install the eight (8) new Anti-Rotation Fuel Injector Clips (1311-9C995) onto the new
Fuel Injectors (M-9593-LU47RSH).

2. Apply assembly lube to the injector O-rings and install the injectors into the new Fuel Rail
(13119F792). NOTE: Verify that the anti-rotation clips are properly aligned and fully
engaged into the fuel rail injector cups.

1313-P2CALIM-GC 20220929 Page 49 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
AIRBOX ASSEMBLY

1. Install the twelve inch length of edge seal (39-211) around the circular opening edge of the air
box where the MAF Tube will be located. Position the seal so the ends start and stop on the
bottom side.

2. Place the MAF tube (R07060101-13) through the opening of the airbox (1313-9643) from the
inside. Install the mounting bracket (R07130010-13) onto the MAF Tube using one M6x14 bolt
(N605771). Align the point on the bracket with the mark on the tube and torque to 10Nm.

1313-P2CALIM-GC 20220929 Page 50 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

3. With the two remaining M6 x 14 fasteners (N605771) secure the bracket to the back of the box
and torque to 10 Nm.

4. Install the stock MAF sensor into the MAF Tube (R07060101) using the MAF Bolts (M4 X 0.7 X
10) and tighten with a T-20 Torx bit. Torque the screws to 1.8 – 2.2 Nm. Be careful not to over
tighten these screws. Wiggle the MAF sensor to ensure that it is properly fastened.

1313-P2CALIM-GC 20220929 Page 51 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

5. Install the retaining grommet from the factory airbox into the mounting tab on the new Airbox
Assembly (1313-9643). Tip – Remove the center bushing while installing the rubber grommet
through the hole in the tab. Re-install the center bushing once the grommet is fully seated.

6. Remove the rubber mounting isolators from the bottom of the factory airbox and install them onto
the mounts on the bottom of the new airbox in the same orientation.

7. Install the Filter (997-495) onto the MAF Tube. Torque clamp to 3 – 5 Nm.

1313-P2CALIM-GC 20220929 Page 52 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
8. Install the Clean Air Tube (1313-9B659-AA) onto the MAF Tube. (NOTE: MAF and PCV port are
located on the same side).

1313-P2CALIM-GC 20220929 Page 53 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
SECTION D – INSTALLATION
The following section will guide you through the final installation of the kit into the vehicle. If you need to
stop during any part of the installation, make sure you cover any open ports in the cylinder heads or
intake manifold to prevent foreign material from contaminating your engine.

INTERCOOLER RESERVOIR MOUNTING

1. Install the Intercooler Degas Bottle (13108D080) with Degas Bottle Cap (9C3Z-8101-B) onto the
fan shroud using (1) M6 x 1.0 x 22 mm bolt (R18020057) from Hardware Kit E. Use the bottle as
a template to mark the second mounting hole with a paint pen. Remove the bottle and drill a
5/16” hole through the fan shroud.

Mark Hole
Here

2. Install (1) M6 J-Clip (N623332) from Hardware Kit E onto the fan shroud. Reinstall the fan
shroud and bolts and torque to 8-12 Nm. Reinstall the intercooler degas bottle using (2) M6 x 1.0
x 22 mm bolts (R18020057) and torque to 8-12 Nm.

1313-P2CALIM-GC 20220929 Page 54 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

The following steps are for vehicles equipped with Automatic Transmissions; if your
vehicle is equipped with a Manual Transmission please skip to Intercooler Radiator
Assembly Mounting.

AUTOMATIC TRANSMISSION OIL COOLER HOSE

1. Wrap the transmission hose (1312-7R081) provided in the parts kit (GY2021-1/2) with ¾” split
convolute provided in the parts kit (1312-TRANSCONV). Finish the ends with electrical tape.
Attach one end to the oil cooler outlet and route as shown. Reuse existing clamp.

2. Attach the opposite end of the transmission oil cooler hose to the transmission line straight
connector as shown. Secure the hose to the connector using the ¾” worm clamp (5407K58)
provided in the parts kit. The transmission oil cooler hose is shown without the ¾” convolute for
clarity.

1313-P2CALIM-GC 20220929 Page 55 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
3. Wrap both transmission oil cooler hoses coming from the transmission with 12 inches of ¾” split
convolute at the FEAD bracket as shown. Finish the ends with electrical tape.

4. Secure the two transmission oil cooler lines to each other and the AC line at the FEAD bracket in
two places using the zip ties (KTI—78070) supplied in the Hardware Kit G. Inspect the hose
routings to ensure there are no pinched hoses and the convolute is positioned to prevent hose
abrasion from other components.

Zip Ties

1313-P2CALIM-GC 20220929 Page 56 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
5. Wrap the other transmission oil cooler line with 12 inches of ¾” split convolute as shown. Finish
the ends with electrical tape.

1313-P2CALIM-GC 20220929 Page 57 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
INTERCOOLER RADIATOR ASSEMBLY MOUNTING

1. Remove the stock radiator side shields (See Appendix A). The push pins will be reused.

2. Remove the (2) upper bolts and (2) lower nuts used to secure the air conditioning condenser core
to the vehicle. The nuts will be reused.

3. Install the new LTR assembly into the vehicle using (2) M6 x 1.0 x 22 mm bolts (R18020057)
found in Hardware Kit E (13116066FRTHKE) at the top, into the radiator and the two nuts that
were removed in the previous step at the bottom. Torque the two bolts and two nuts to 8-12 Nm.

New Bolts Here

Take Off
Nuts Here

1313-P2CALIM-GC 20220929 Page 58 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
ELECTRIC WATER PUMP, MOUNTING BRACKET AND HOSES

1. Install the Intercooler Pump Inlet Hose (13108D029) from the degas bottle outlet port to the front
of the LTR by routing the hose around the lower radiator hose “T” joint and along the frame rail.
Secure the hose to the bottom of the degas bottle using (1) ¾” constant tension clamp (CT19x12-
BO). Orient the clamps so the “I” on the hose is in the center of the clamp tangs.

2. Install the modified LH side radiator side shield (See Appendix A) and route the Intercooler Pump
Inlet Hose (installed in the previous step) through the new hole in the shield and secure the shield
to the chassis using the take off push pins.

NOTE:
The bumper beam has
been removed for clarity.

1313-P2CALIM-GC 20220929 Page 59 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
3. Install the modified RH side radiator side shield (See Appendix A). Secure the shield to the
chassis using the take off push pins.

NOTE:
The bumper beam has
been removed for clarity.

4. Remove the (2) upper, inner front bumper beam bolts.

5. Install the (2) Long Bumper Bolts (R18020007) from Hardware Kit E in place of the (2) which
were just removed and torque to 20-30 Nm. Install the Intercooler Pump Mounting Bracket
(1313-8C419) behind the bumper onto the long bumper bolts using (4) M8 nuts (W520413) from
Hardware Kit E (13116066FRTHKE). Torque these nuts to 20-30 Nm.

View from inside engine

bay looking down

1313-P2CALIM-GC 20220929 Page 60 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
6. Install the Intercooler Pump to Bumper Beam NVH Isolator (13108Z419) found in Hardware Kit E,
on the rear of the bumper beam such that the edge of the pad is 220mm from the driver side
bumper beam mounting plate and 60mm from the front edge.

220 mm

60 mm
View from in front of vehicle,
looking down at bumper beam

7. Connect the Intercooler Pump to LTR hose (13108K236) to the Intercooler Pump and Bracket
assembly (392022009 or FS00057975) If kit includes Pump PN: FS00057975, use P CLIP
(8863T95), and M8 Bolt (W500224-S437) to install on bracket. Orient the hose so the “I” is
aligned with the arrow on the pump outlet port. Secure the hose to the pump using (1) ¾”
constant tension clamp (CT19x12-BO). Orient the clamp so the “I” on the hose is in the center of
the clamp tangs.

1313-P2CALIM-GC 20220929 Page 61 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
8. Secure the Intercooler Pump and hose to the Intercooler Pump Mounting Bracket using (2) M8 x
1.25 x 25 mm bolts (W500224) from Hardware Kit E so the outlet is facing away from the two
holes that are in the bracket. Torque bolts to 20-30 Nm. (SKIP THIS STEP IF PUMP
INSTALLED IN STEP 7 WITH P-CLIP)

9. Connect the Intercooler Pump to LTR hose to LTR inlet port using (1) ¾” constant tension clamp.
Orient the clamp so the “I” on the hose is in the center of the clamp tangs.
View from inside engine bay
Bumper beam looking toward the ground
removed for clarity

10. Connect the Intercooler Pump Inlet Hose to the inlet port on the intercooler pump. Secure the
hose to the pump using (1) ¾” constant tension clamp. Orient the clamp so the “I” on the hose is
in the center of the clamp tangs.

1313-P2CALIM-GC 20220929 Page 62 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

View from in front of

vehicle, looking down
at bumper beam

11. Route the remainder of the Intercooler Pump Wiring Harness next to the headlight and radiator
and through the hole in the RH Radiator Side Shield. Connect the wiring harness to the pump
and secure the harness to the bracket by pushing the push pins on the harness into the holes in
the mounting bracket. If Intercooler pump PN: FS00057975 is in your kit, install jumper harness
PN: PT00045528 inline between wiring harness and pump.

Route wiring
harness here

LTR

RH Side
Shield

12. Reinstall the impact absorber onto the front bumper beam using the take out pushpins.
Note: Route all intercooler hoses very carefully. It is critical for intercooler
performance that these hoses are not kinked once installed into the vehicle.

1313-P2CALIM-GC 20220929 Page 63 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
INDUCTION RESONANCE TUBE DELETE GROMMET

1. Install the Induction Resonance Tube Delete Grommet (W651016) in the hole that was exposed
when the boom tube was removed.

NOTE: If the ROUSH boost gauge kit is going to be installed onto the vehicle, the above grommet
can be left out as the boost gauge kit has a pre-installed grommet on the vacuum line that will go in
this location.

1313-P2CALIM-GC 20220929 Page 64 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
INTAKE MANIFOLD AND SUPERCHARGER INSTALLATION

1. Remove the tape from the cylinder heads and clean the cylinder head to intake manifold mating
surfaces.

2. Install the intake manifold using six (6) M6 x 1.0 x 40 mm bolts (R18020004) found in Hardware
Kit B (1311-TVSHKB). Install these fasteners in the positions shown and tighten the sequence in
two stages. Stage 1; torque bolts to 8-12 Nm. Stage 2; tighten bolts an additional 45 degrees.
Reinstall the engine wiring harness retention clips at the rear of the intake manifold.

5 1 3

Wiring
Retainers
Here

6 2 4

3. Lube the fuel injector o-rings with assembly lube. Install the fuel rail and injectors into the intake
manifold using the take off bolts. Be sure each injector is properly seated into the intake
manifold. Tighten the bolt pattern in two stages. Stage 1; torque bolts to 8-12 Nm. Stage 2;
tighten bolts an additional 90 degrees.

1 3

2 4

1313-P2CALIM-GC 20220929 Page 65 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
4. Connect the eight fuel injector connectors.
5. Remove the supercharger assembly (1311H-6F066) from the protective packaging and carefully
place on top of the intake manifold. Ensure that the supercharger is fully seated on the intake
mounting dowels. Remove protective shipping covers.

6. Install the 85mm supercharger pulley (1313-6K85) onto the hub of the supercharger using the six
(6) M6 x 16 bolts (W500013) found in Hardware Kit B (1311-TVSHKB). Apply a small amount of
blue thread locking compound to each bolt and torque to 8-12 Nm.

7. Install the ten (10) M8 x 53 fasteners (N808130) provided found in Hardware Kit B (1311-
TVSHKB) into the mounting holes. Torque fasteners in three steps; 10 Nm, 20 Nm and 30 Nm in
the sequence shown.

7 3 1 5 9

10

8 4 2 6

1313-P2CALIM-GC 20220929 Page 66 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
8. Connect the supercharger bypass reference vacuum line (7R3V-9E498) to the bottom fitting on
the supercharger bypass actuator. Route this underneath the heater hose and fuel line.

9. Install the throttle spacer to supercharger gasket (R07060152) between the throttle body spacer
assembly and the supercharger and mount the spacer using (4) M6 x 32 fasteners (R18020009).
These parts can be found in Hardware Kit B (1311-TVSHKB). Torque the fasteners to 8-12 Nm.

1313-P2CALIM-GC 20220929 Page 67 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
10. Connect the boost bypass hose from the throttle body spacer to the top port of the supercharger
bypass actuator.

11. (Manual Trans Only) Connect the brake booster vacuum line to the check valve on the brake
booster.

11-a. (Auto Trans Only) Connect the end of hose 3 of the Brake Aspirator Assembly to the brake
booster connector. Secure the connection using Clamp 5

Brake Booster Connector

1313-P2CALIM-GC 20220929 Page 68 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
12. Connect the new Evaporative Emission Canister Purge Valve electrical connector.

13. Install the new Evaporative Emission Canister Purge Valve Line (BR3V-9G271) from the fitting
below the brake booster to the relocated Purge Valve on the Throttle Body Spacer.

14. Connect the fuel inlet line to the fuel rail.

1313-P2CALIM-GC 20220929 Page 69 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
16. Connect the PCV Purge Line (13116K817) to the PCV Valve on the passenger side cam cover
and the port on the supercharger.

17. Install the Throttle Body Gasket (R07060153) in the Throttle Body Spacer. Use (4) M6 x 1.0 x
32.5 mm bolts (R18020009) to secure the Throttle Body Assembly (R07060150) to the Spacer.
Torque bolts to 8-12 Nm. These can be found in Hardware Kit B (1311-TVSHKB).

1313-P2CALIM-GC 20220929 Page 70 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
18. Connect the TPS and ETC Throttle Body electrical connectors.

1313-P2CALIM-GC 20220929 Page 71 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
FEAD ASSEMBLY

1. Remove the (4) bolts and (1) stud from the front cover as shown.

One of these two

bolts will be reused

2. Remove and discard the 10mm water pump fastener shown below.

Remove
&
Discard

1313-P2CALIM-GC 20220929 Page 72 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
3. Install the Upper FEAD Bracket (13148B653U) using one (1) M8x1.25x57 bolt that was
removed in the previous step, three (3) M8x1.25x60 bolt (111116346) and two (2) M8x1.25x84
bolts (W704752) from Hardware Kit C (13116066FRTHKC). Torque bolts to 20-30 Nm.

W704752

Reuse take out

M8x1.25x57
bolt here

111116346

4. Install qty 1 dust shield (PT00040547) per the (2) Idler Pulleys (953045) onto the machined
posts of the Upper FEAD Bracket. Secure the pulleys using (2) M8 x 1.25 x 28mm idler bolts
(R18020060) found in Hardware Kit C. Torque bolts to 25 Nm. You will have one extra Dust
shield for a spare in case it is damaged during installation. Be sure to center dust shield prior to
torquing and test spin for no noise.

1313-P2CALIM-GC 20220929 Page 73 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
5. Loosely install the FEAD Tensioner Bracket Assembly (13118B603) onto the front cover using
(2) M8 x 1.25 x 120mm (N811329) bolts found in Hardware Kit C, leaving at least a 10mm gap
between the two new FEAD brackets.

Leave a 10mm gap

between these bosses
to allow for the FEAD
belt to be installed.

1313-P2CALIM-GC 20220929 Page 74 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
6. Route the FEAD belt (6K2085-8620). Do not route the belt onto the supercharger pulley.

Pulleys with Dust

cover installed

7. Install (1) M8 x 1.25 x 41mm (W705128) bolt found in Hardware Kit C, to fasten the Tensioner
Bracket to the Upper FEAD Bracket. Torque all three Tensioner Bracket bolts to 20-30 Nm.

1313-P2CALIM-GC 20220929 Page 75 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
8. Using a 17mm socket, rotate the new tensioner clockwise to install the belt on to the
supercharger pulley. Inspect each pulley to ensure the belt is properly seated.

Use this nut to rotate the

tensioner and enough slack
to install the FEAD belt.

9. Re-install the Coolant Pump Pulley using the (4) take off bolts. Torque bolts to 20-30 Nm.

1313-P2CALIM-GC 20220929 Page 76 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
10. Re-install the stock FEAD Belt by rotating the tensioner counter-clockwise and routing the belt
as per the stock Ford belt routing.

1313-P2CALIM-GC 20220929 Page 77 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
COOLANT HOSES

1. Install the Intercooler LTR Outlet hose (13118D030). Route the hose from the LTR, behind the
passenger side headlamp to the lower intercooler turret on the front of the intake manifold.
Secure the hose using (2) ¾” constant tension clamps. Orient the clamps so the “I” on the hose
is in the center of the clamp tangs.

View from underneath RH Rad.

front passenger side Side Shield

Rad. Drain
Petcock

2. Install the Degas Bottle Inlet Hose (13118D031) from the upper intercooler turret to the upper
degas bottle fitting using (2) ¾” constant tension clamps. Orient the clamps so the “I” on the hose
is in the center of the clamp tangs.

1313-P2CALIM-GC 20220929 Page 78 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
3. Reinstall the upper radiator hose.

4. Reinstall the factory degas bottle onto the fan shroud and torque the bolt to 8 – 12 Nm.

5. Before reinstalling the factory heater feed and return hoses you must first install the protective
sleeve material supplied with this kit in the areas shown below.

a) Install one length of protective sleeve (1311-18K579SLV) onto the passenger side heater
hose. Slide it over the quick connect fitting and along the heater hose. Apply electrical tape over
either end of the protective sleeve to secure its position on the hose.

1313-P2CALIM-GC 20220929 Page 79 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
b) Install the other length of protective sleeve (1311-18K579SLV) over the quick connect fitting
and along the heater hose on the drivers side. Apply electrical tape over either end of the
protective sleeve to secure its position on the hose.

6. Install the 3/8” Engine Bottle Degas Hose (13118276) from the engine degas bottle to the fitting
on the driver side cylinder head. Secure with the constant tension clamps removed from the
factory hose. Ensure both ¾” intercooler hoses, the degas hose and all clamps and wiring
have been installed to provide maximum clearance to the supercharger belt.

1313-P2CALIM-GC 20220929 Page 80 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
AIR INDUCTION SYSTEM

1. Install the 9” Edge Seal (R07130026) located on the left side of the airbox.

2. Install the 12” length of Edge Seal (R07130026) along the top edge of the airbox, overtop of the
MAF Tube.

3. Install both of the 4” lengths of Edge Seal (R07130026-13) onto the edges around the bottom of
the airbox.

1313-P2CALIM-GC 20220929 Page 81 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
7. Install the new airbox assembly into the vehicle. Secure the airbox to the chassis using the take
off M6 bolt from the original airbox and torque to 8 – 12 Nm. Install the M6 Nut in Hardware kit
over the stud for the fan shroud. Upper Lid is removed to show clarity and get better tool access.

Install Nut
Here

Install Bolt
Here

8. Install the Clean Air Tube (1313-9B659) in the vehicle using (2) hose clamps (R07130015) from
Hardware Kit A. Torque clamps to 3 Nm. Install the PCV Fresh Air Inlet tube (13116758) by
connecting the 90 deg fitting to the driver side cam cover and angled fitting to the PCV fitting in
the clean air tube

1313-P2CALIM-GC 20220929 Page 82 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
9. Connect the open end of the supercharger bypass reference line (7R3V-9E498) to the fitting on
the clean air tube.

9-a. (Auto Trans Only) Connect Hose 1A of the Brake Vacuum Aspirator Assembly to the 3/8”
vacuum port on the Clean Air Tube

1313-P2CALIM-GC 20220929 Page 83 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
9-b. (Auto Trans Only) Review the Brake Vacuum Aspirator Assembly in the vehicle to
ensure there are no pinched hoses and the convolute is positioned to prevent hose abrasion
from other components. Final installation should look like the image below.

Route the MAF wire harness around the air box and connect the harness to the MAF Sensor.
Make sure the red lock is engaged on the connector.

1313-P2CALIM-GC 20220929 Page 84 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED

SECTION E- FINAL ASSEMBLY

1. Fill the engine cooling system (using a proper coolant mixture) to the marked level on the
radiator degas bottle.

2. Using the same coolant mixture, fill the intercooler system. The coolant should be
approximately one inch below the top of the cap.

Important: Both coolant systems can trap a large amount of air. It is very important to
verify that the air is purged and that coolant is flowing properly through both systems.
Roush recommends vacuum filling both systems to properly evacuate the trapped air.

3. Reinstall front bumper cover, lower close-out panel and inner fenders by reversing the removal
procedures.

4. Reinstall the front wheels/tires. Torque wheel lugs to the factory Ford specifications.

5. Inspect all underhood wiring harnesses for potential interference issues. Use zip ties to safely
position the harness away from any areas of concern.

6. Reinstall the radiator trim cover by reversing the removal instructions.

7. If the PCM was removed and shipped to ROUSH for a ROUSH performed flash, reinstall it once
the PCM is returned from ROUSH. If you are equipped with a SAE J2534 pass through device,
refer to the PCM Flashing section when installation is complete. DO NOT ATTEMPT TO
REINSTALL THE PCM AND START THE VEHICLE IF THE PCM IS NOT EQUIPPED WITH A
ROUSH CALIBRATION. OPERATING THE ENGINE WITHOUT THE RECALIBRATED PCM
WILL RESULT IN ENGINE DAMAGE OR FAILURE AND WILL VOID THE WARRANTY.

8. Reinstall the battery connections by connecting the positive cable first then connecting the
negative cable.

9. Reconnect the fuel pump control module electrical connector located in the spare tire stowage
compartment.

1313-P2CALIM-GC 20220929 Page 85 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
10. The Belt Routing Diagram (13116E072) is to be placed on the underside of the hood, on the
driver side, opposite of the factory Vehicle Emission Control Information decal.

Place Decal
in This Area

11. Place the EO Label (D41822-9A095EO) under hood in a visible location (on the bottom side of
the hood or on the strut tower).

12. Place the “Premium Fuel” (13109A095) white decal with black lettering on the arm door of the
fuel filler door as shown.

Place Decal Here

1313-P2CALIM-GC 20220929 Page 86 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
13. Place the “Premium Fuel” (R07110004) clear decal with white lettering on the instrument cluster
bezel, on the flat area below the small center gauges as shown.

Place Decal Here

14. If performing the PCM Flash procedure, proceed to the “PCM Flashing” section. If the
PCM was sent to ROUSH for the Optional ROUSH Performed Flash and it has been
reinstalled, start the engine and check for unusual noise, dash service lights, and/or unusual
operation. If problems are detected, immediately stop the engine or vehicle, diagnose and
repair the problem.

1313-P2CALIM-GC 20220929 Page 87 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
PCM FLASHING

1. If equipped with a SAE J2534 pass through device, refer to the RDT-CALIM manual included in
the CALKIT for PCM flashing. The RDT-CALIM manual will guide you through the ROUSH
Diagnostic Tool (RDT) software installation process and the ROUSH PCM flashing procedure.
OPERATING THE ENGINE WITHOUT THE RECALIBRATED PCM WILL RESULT IN
ENGINE DAMAGE OR FAILURE AND WILL VOID THE WARRANTY.

2. Once the PCM has been successfully re-calibrated, start the engine and check for unusual
noises, dash service lights, and unusual operation. If problems are detected, immediately stop
the engine or vehicle, diagnose and repair the problem.

APPENDIX A – SIDE SHIELD MODIFICATIONS

1- Remove the LH radiator side shield from the vehicle by removing the two push pin
retainers.

1313-P2CALIM-GC 20220929 Page 88 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
2- Cut the rubber edge of the side shield in three (3) places as shown.

Cut along
plastic edge

35 mm 100 mm

3- Using a hole saw, drill a 1 3/8” hole through the plastic portion of the shield 180mm from
the end as shown.

180 mm

4- Re-install the LH radiator side shield using the take off push pins.

1313-P2CALIM-GC 20220929 Page 89 of 90 1-800-59-ROUSH

 PREMIUM FUEL REQUIRED
5- Remove the RH radiator side shield from the vehicle by removing the two push pins.

6- Cut the rubber edge of the side shield in three (3) places as shown.

Cut along
plastic edge

125mm 40 mm

7- Re-install the RH radiator side shield using the take off push pins.

1313-P2CALIM-GC 20220929 Page 90 of 90 1-800-59-ROUSH