4120EC PROGRAMMING FORM

DEFAULT VALUES, WHERE APPUCABLE, ARE SHOWN IN BRACKETS [ ]

●OO INSTALLER CODE ●32 SUBSCRIBER #

00-09; B-F
mmmm
●u1 MASTER CODE Y33 PRIMARY PHONE #
❑ n(lrl [ENTER&9, [134] ❑ nclclnclclmclclclcw
*O2 RESPONSE TYPE ( O&lo) ●34 SECONDARY PHONE #

d d b ckl ‘ones
❑ lnclclnclclclclclclcl”
[019] [011] [013] [014] ’35 CS DOWNLOAD PHONE #

C&lb 6 dl ‘ones
[015] [016] [o171 [Opq
Elclmlnclnclnnclcl”’
’36 CS lD# 00-09; A-F

*O5 MULTIPLE ALARMS & RESPONSE TYPES mlmlmmnlmlnlnl

FOR KEYPAD PANICS [115] [1 15] [115] 115] [1 15] 115] [1 [5] 1Is]

mmm ●4O PROGRAM TAMPER CODE

Multiple Alarms 3 & # (or C) ●&#(or B)
[010] [ol~ [016] m ~9: 64 [Op]

1st location: 00 = one alarmfper zonelper armed period; 01. multiple *4I DISABLE USAGE OF EOLR SUPERV. ON ZONE 1 ‘
alarms/per zone/per armed period.
2nd & 3rd locations: enter response types for keypad panics.
❑ I =NoEOLR; O=EOLR supervision [0]

RESPONSE TYPES ’44 RING DETECT COUNT

00. unusedZone 05= Trouble by dayl Alarm by night
01 = SE #1 C6 = 24-hour Silant l--!-l [010]
00= no ring detect 01-14 for ring counts of 1-1 4; 15 when telephone
02= Not US’d 07= 24-hour Audible
answering machine is cwwted to the same phone line.
03- Perimetar 08= 24-hour Auxiliary
04 = Interior Follower 09. Fire
PRIMARY TRANSMISSION FORMAT

●O8 N.O. or N.C. SENSOR LOOP (ZONES 14) ‘?5

[0]
0. ADEMCO LO SPEED; 1 = RADIONICS; 2 = ADEMCO EXPRESS

bflflbflflbfl ’48 SECONDARY TRANSMISSION FORMAT

[1] [1] [1] [1] [1] [1] [1] [1] 0. ADEMCO LO SPEED; 1 = RADIONICS; 2 = ADEMCO EXPRESS
O = N.O. Sensor Loop; 1 = N.C. Sensor LMp. •1
[0]
●O9 ENTRY DELAY ●1 O EXIT DELAY *49 CHECKSUM VERIFY
~ X15secsp3C-15) ~ X15 S’CSW-15) ❑ l= Yes, O=No [0]
[0[2] [013]
●54 4+2 ZONE FORMAT SELECTION
’13 ALARM SOUNDER TIME DURATION 1 = 4+2 Format, O = 3+1/4+1 [0]
•1
*55 ALARM REPORT ●56 RESTORE REPORT
’14 ZONE 8 RESPONSE TIME
•1
0 = Standard, 1. Expanded ❑ O. Standard,l =Expanded

❑ O = Slow, 1 = Fast [0] [0] [1]

●21 NO FIRE TIME-OUT ’57 BYPASS REPORT ●58 TROUBLE REPORT

O. Standard, 1 = Expanded m o= Standard, 1 = Expandad
l= Yes, O=No [0] •1
•1
[0] [0]
●25 DISABLE DURESS IN ADEMCO EXPRESS FORMAT
●59 OPEN/CLOSE REPORT
l= Yes, O=No [0]
•1 O. Standard, 1 = Expanded
•1
●27 TEST REPORT INTERVAL [1]

O = No report; 1 = 12 hrs.; 2 = 24 hrs.; 3 = 168 hrs. *6O LOW BAT, AC LOSS& TEST REPORT
•1
[2]
O = Standard, t . Expended
•1
●29 QUICK ARM ’30 TOUCH-TONE DIAL
●65 ALARM REPORTING CODES ASSIGNED
l= Yes, O=No u l. Yes, O. Rotary
•1
[1] [0] mmmmmmmm
’31 PABX CODE
-—— — ;I)] [$] [70] [;0] [fo] [0;:] [~0] Ho]
L!-ll_!_J l_!._l L_!_l””’S-F Enter 01-1 5; 00 = no code repordng
When reporting 4+2 format, 2nd digit is always zone number)
I (NOTE:

WWW.DIYALARMFORUM.COM 4120EC-PR V3 9/93

●66 ALARM REPORTING CODES ASSIGNED (CONT’D) NON-ALARM CODES ●67 “68
(01-15)
mmm (01-15); 00=no channel reporting AC LOSS
I.--u open~ I J
Duress 3&?# Panic
(or C)
*& #Panic
(or B)
See Note in ●65 (00 for no AC Loss 2nd Digit
m Close ml
[010] [010] [010] code Trbl r-i-1 Lo Bat ~

reporting) Trbl Restr

ml L. Bat 2- fJigit
m
Bypass
m m
‘est
Bypass Restr
~ m
Cance’
flstr code for Alrrn, Ill
[ I
AC Loss, Lo Bat
Defaults for above are all 010

HEXADECIMAL TO NUMERIC ENTRY CONVERSION

O = 10 (REPORT CODES)
O =00 (SUBS ID, PABX OR CS ID)
1=01 , 2=02, 3 =03 , 4=04, 5=05, 6=06 , 7=07, 8=08, 9=09, 6=11, C=12, D=13, E=14 , F=l 5

● To Enter Program Mode: a) Press [*] and [#] at the same time within 30 seconds after power is applied to the
control, or
b) Enter installer code+ [8]+ [0] + [0]. Enter first field address to begin programming *
(e.g., ●O1).
1 3
I ● To Set Standard Defaults: Press ●96 I

I Press *99 or ●98: *99 allows re-entry to the programming mode by installer code.
To Exit Program Mode:
I
●

*98 prevents re-entry to programming mode by installer code.

2NDEMC0
A DIVISION OF PllllVAY CORPORATION

WWW.DIYALARMFORUM.COM 4120EC-PR V3 9/93