Technical Data Sheet
TSE322SK
Description
TSE322SK is a one-component heat curable silicone adhesive which cures rapidly at elevated
temperatures, and adheres to a variety of substrates without the use of primers. TSE322SK has
high elongation which helps absorb stress.
Key Features and Typical Benenfits
One component product - no mixing required
Fast cure at elevated temperature
Primerless adhesion to many types of substrates
High elongation
Non-corrosive to metals and sensitive substrates
Excellent dielectric propreties
Typical Physical Properties (JIS
K 6249)
Property Unit Value
Uncured Properties
Appearance Semi-flowable, white
Viscosity (23 °C) Pa·s 220
Cured Properties (cured 1 hour at 150 °C)
Density (23 °C) g/cm3 1.24
Hardness (Type A) 25
Elongation % 440
Tensile Strength MPa 3.2
Adhesion Strength(1) MPa 1.8
Dielectric Strength kV/mm 2.6
Dielectric Constant (60Hz) 2.9
Dissipation Factor (60Hz) 0.003
Volume Resistivity Ω·cm 5.0 x 1015
Typical properties are average data and should not be used as or to develop product specifications.
(1)PPS Lap Shear
HCD-TSE322SK (Rev. 2020-09-17 6:23 AM) Page 1 of 7
TSE322SK
Note: Test data. Actual results may vary.
HCD-TSE322SK (Rev. 2020-09-17 6:23 AM) Page 2 of 7
TSE322SK
Note: Test data. Actual results may vary.
Lap Shear and Hardness
Note: Test results. Actual results may vary.
Note: Test results. Actual results may vary.
HCD-TSE322SK (Rev. 2020-09-17 6:23 AM) Page 3 of 7
TSE322SK
Note: Test results. Actual results may vary.
Processing Reccomendations
Compatibility
HCD-TSE322SK (Rev. 2020-09-17 6:23 AM) Page 4 of 7
TSE322SK
TSE322SK silicone adhesive will cure in contact with most clean, dry surfaces. However, certain
materials, such as butyl and chlorinated rubber, sulfur-containing materials, amines, and certain
metal soap cured RTV silicone rubber compounds can cause cure inhibition. cure inhibition is
characterized by a gummy appearance at the iinterface between the adhesive and the substrate to
be bonded. It is recommended that a sample patch test be performed with TSE322SK to
determine substrate compatibility.
Surface Preparation
The adhesive performance of any polymer system is highly dependent upon proper surface
preparation. In order to maximize the adhesion of TSE322SK and minimize the potential for cure
inhibition, all parts should be as clean and dry as possible prior to the application of the adhesive.
Packaging
1 kg can in cases of 10
333 ml cartridge
General Considerations for Use
While the typical operating temperature for silicone materials ranges from -45℃ to 200℃, the
long-term maintenance of its initial properties is dependent upon design related stress
considerations, substrate materials, frequency of thermal cycles, and other factors.
Patent Status
Nothing contained herein shall be construed to imply the nonexistence of any relevant patents or to
constitute the permission, inducement or recommendation to practice any invention covered by any
patent, without authority from the owner of the patent.
Product Safety, Handling and Storage
Customers should review the latest Safety Data Sheet (SDS) and label for product safety
information, safe handling instructions, personal protective equipment if necessary, emergency
service contact information, and any special storage conditions required for safety. Momentive
Performance Materials (MPM) maintains an around-the-clock emergency service for its products.
SDS are available at www.momentive.com or, upon request, from any MPM representative. For
product storage and handling procedures to maintain the product quality within our stated
specifications, please review Certificates of Analysis, which are available in the Order Center. Use
of other materials in conjunction with MPM products (for example, primers) may require additional
precautions. Please review and follow the safety information provided by the manufacturer of such
other materials.
Limitations
Customers must evaluate Momentive Performance Materials products and make their own
HCD-TSE322SK (Rev. 2020-09-17 6:23 AM) Page 5 of 7
TSE322SK
determination as to fitness of use in their particular applications.
Contact Information
For product prices, availability, or order placement, contact our customer service at
Momentive.com/CustomerService/
For literature and technical assistance, visit our website at: www.momentive.com
DISCLAIMER:
THE MATERIALS, PRODUCTS AND SERVICES OF MOMENTIVE PERFORMANCE
MATERIALS INC. AND ITS SUBSIDIARIES AND AFFILIATES (COLLECTIVELY “SUPPLIER”),
ARE SOLD SUBJECT TO SUPPLIER’S STANDARD CONDITIONS OF SALE, WHICH ARE
INCLUDED IN THE APPLICABLE DISTRIBUTOR OR OTHER SALES AGREEMENT, PRINTED
ON THE BACK OF ORDER ACKNOWLEDGMENTS AND INVOICES, AND AVAILABLE UPON
REQUEST. ALTHOUGH ANY INFORMATION, RECOMMENDATIONS, OR ADVICE CONTAINED
HEREIN IS GIVEN IN GOOD FAITH, SUPPLIER MAKES NO WARRANTY OR GUARANTEE,
EXPRESS OR IMPLIED, (i) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED
UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY
DESIGN INCORPORATING ITS PRODUCTS, MATERIALS, SERVICES, RECOMMENDATIONS
OR ADVICE. EXCEPT AS PROVIDED IN SUPPLIER’S STANDARD CONDITIONS OF SALE,
SUPPLIER AND ITS REPRESENTATIVES SHALL IN NO EVENT BE RESPONSIBLE FOR ANY
LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS OR SERVICES
DESCRIBED HEREIN. Each user bears full responsibility for making its own determination as to
the suitability of Supplier’s materials, services, recommendations, or advice for its own particular
use. Each user must identify and perform all tests and analyses necessary to assure that its
finished parts incorporating Supplier’s products, materials, or services will be safe and suitable for
use under end-use conditions. Nothing in this or any other document, nor any oral recommendation
or advice, shall be deemed to alter, vary, supersede, or waive any provision of Supplier’s standard
Conditions of Sale or this Disclaimer, unless any such modification is specifically agreed to in a
writing signed by Supplier. No statement contained herein concerning a possible or suggested use
of any material, product, service or design is intended, or should be construed, to grant any license
under any patent or other intellectual property right of Supplier covering such use or design, or as a
recommendation for the use of such material, product, service or design in the infringement of any
patent or other intellectual property right.
Momentive and the Momentive logo are trademarks of Momentive Performance
Materials Inc.
HCD-TSE322SK (Rev. 2020-09-17 6:23 AM) Page 6 of 7
TSE322SK
HCD-TSE322SK (Rev. 2020-09-17 6:23 AM) Page 7 of 7
