JOB NO. ITEM NO.
Brown & Root, Inc. PURCHASE ORDER NO.
SPECIFICATION NO.
CENTRIFUGAL COMPRESSOR REVISION NO. DATE `
DATA SHEET (API 617-6TH) PAGE 1 OF 6 BY
SI UNITS
1 APPLICABLE TO: PROPOSAL PURCHASE AS BUILT
2 FOR UNIT
3 SITE SERIAL NO.
4 SERVICE NO. REQUIRED
5 CONTINUOUS INTERMITTENT STAND BY DRIVER TYPE (3.1.1)
6 MANUFACTURER MODEL DRIVER ITEM NO.
7 NOTE: INFORMATION TO BE COMPLETED: BY PURCHASER BY MANUFACTURER
8 OPERATING CONDITIONS
9 OTHER CONDITIONS (3.1.2)
10 (ALL DATA ON PER UNIT BASIS) NORMAL A B C D E
11
12
13 GAS HANDLED (ALSO SEE PAGE )
14 m³/h (1.013 BAR & 0 °C DRY)
15 WEIGHT FLOW, kg/h (WET) (DRY)
16 INLET CONDITIONS
17 PRESSURE (BAR) (kPa abs)
18 TEMPERATURE (°C)
19 RELATIVE HUMIDITY %
20 MOLECULAR WEIGHT (%)
21 Cp/Cv ( K1) OR (KAVG)
22 COMPRESSIBILITY (Z1) OR (ZAVG)
23 INLET VOLUME, (m³/h) (WET / DRY)
24 DISCHARGE CONDITIONS
25 PRESSURE (BAR) (kPa abs)
26 TEMPERATURE (°C)
27 Cp/Cv (K2) OR (KAVG) NOTE 1
28 COMPRESSIBILITY (Z1) OR (ZAVG) NOTE 1
29
30 kW REQUIRED (ALL LOSSES INCLUDED)
31 SPEED (RPM)
32 ESTIMATED SURGE, m³/h (AT SPEED ABOVE)
33 POLYTROPIC HEAD (N-m/kg)
34 POLYTROPIC EFFICIENCY (%)
35 CERTIFIED POINT
36 PERFORMANCE CURVE NUMBER
37 PROCESS CONTROL
38 METHOD SUCTION THROTTLING VARIABLE INLET SPEED VARIATION DISCHARGE COOLED BYPASS
39 FROM (BAR)(kPa abs) GUIDE VANES FROM % BLOWOFF FROM
40 TO (BAR)(kPa abs) (3.4.2.4) TO % TO TO
41
42 SIGNAL SOURCE ( 3.4.2.1)
43 TYPE ELECTRONIC PNEUMATIC OTHER
44 RANGE MA (BAR)(kPa abs)
45
46 ANTI-SURGE BYPASS MANUAL AUTOMATIC NONE
47
48 REMARKS:
49
50 NOTE 1: IF GAS ANALYSIS IS GIVEN, MANUFACTURER SHALL SUPPLY DATA, OTHERWISE DATA SHALL BE SUPPLIED BY USER.
07/96 EF-050-90.09-M SHT 1 OF 6 API617SI.XLS REV 0
Brown & Root, Inc.
JOB NO. 0 ITEM NO.
CENTRIFUGAL COMPRESSOR REVISION NO. 0 DATE ###
DATA SHEET (API 617-6TH) PAGE 2 OF 6 BY 0
SI UNITS
1 OPERATING CONDITIONS (Continued) (3.1.2) (3.1.3)
2 GAS ANALYSIS: OTHER CONDITIONS (2.11.1.3)
3 MOL % NORMAL A B C D E REMARKS: (2.11.1.8)
4 MW
5 AIR 28.966
6 OXYGEN 32.000
7 NITROGEN 28.016
8 WATER VAPOR 18.016
9 CARBON MONOXIDE 28.010
10 CARBON DIOXIDE 44.010
11 HYDROGEN SULFIDE 34.076 (2.11.1.7)
12 HYDROGEN 2.016
13 METHANE 16.042
14 ETHYLENE 28.052
15 ETHANE 30.068
16 PROPYLENE 42.078
17 PROPANE 44.094
18 I-BUTANE 58.120
19 n-BUTANE 58.120
20 I-PENTANE 72.146
21 n-PENTANE 72.146
22 HEXANE PLUS
23
24
25 TOTAL
26 AVG. MOL. WT.
27 LOCATION: (2.1.9) NOISE SPECIFICATIONS: (2.1.10)
28 INDOOR OUTDOOR GRADE APPLICABLE TO MACHINE:
29 HEATED UNDER ROOF MEZZANINE SEE SPECIFICATION
30 UNHEATED PARTIAL SIDES APPLICABLE TO NEIGHBORHOOD:
31 ELEC. AREA CLASSIFICATION (2.1.15) CL GR DIV SEE SPECIFICATION
32 WINTERIZATION REQ'D. (2.1.9) TROPICALIZATION REQ'D. ACOUSTIC HOUSING: YES NO
33 SITE DATA: (3.4.6.6) APPLICABLE SPECIFICATIONS:
34 ELEVATION m BAROMETER BAR API 617, CENTRIFUGAL COMPR. FOR GEN. REFINERY SERV.
35 RANGE OF AMBIENT TEMPS: VENDOR HAVING UNIT RESPONSIBILITY (2.9.1.7)
36 DRY BULB WET BULB
37 NORMAL °C GOVERING SPECIFICATION (IF DIFFERENT)
38 MAXIMUM °C
39 MINIMUM °C PAINTING:
40 °C MANUFACTURER'S STD.
41 UNUSUAL CONDITIONS: DUST FUMES OTHER
42 OTHER (2.1.9)
43 SHIPMENT: (4.4.1)
44 DOMESTIC EXPORT EXPORT BOXING REQ'D.
45 REMARKS: OUTDOOR STORAGE MORE THAN 6 MONTHS (4.4.1)
46 SPARE ROTOR ASSEMBLY PACKAGED FOR (4.4.3.10)
47 HORIZONTAL STORAGE VERTICAL STORAGE
48
49
50
51
07/96 EF-050-90.09-M SHT 2 OF 6 API617SI.XLS REV 0
Brown & Root, Inc.
JOB NO. 0 ITEM NO.
CENTRIFUGAL COMPRESSOR REVISION NO. 0 DATE ###
DATA SHEET (API 617-6TH) PAGE 3 OF 6 BY 0
SI UNITS
1 CONSTRUCTION FEATURES
2 SPEEDS: TYPE (OPEN, ENCLOSED, ETC.)
3 MAX. CONT. RPM TRIP RPM TYPE FABRICATION
4 MAX. TIP SPEEDS: m/s @ 100% SPEED MATERIAL
5 m/s @ MAX. CONT. SPEED MAX. YIELD STRENGTH (N)
6 LATERAL CRITICAL SPEEDS (DAMPED) BRINNEL HARDNESS: MAX MIN
7 FIRST CRITICAL RPM MODE SMALLEST TIP INTERNAL WIDTH (mm)
8 SECOND CRITICAL RPM MODE MAX. MACH. NO. @ IMPELLER EYE
9 THIRD CRITICAL RPM MODE MAX. IMPELLER HEAD @ 100% SPD (N-m/kg)
10 FOURTH CRITICAL RPM MODE SHAFT:
11 TRAIN LATERAL ANALYSIS REQUIRED (2.9.2.3) MATERIAL
12 TRAIN TORSIONAL ANALYSIS REQUIRED DIA @ IMPELLERS (mm) DIA @ COUPLING (mm)
13 (TURBINE DRIVEN TRAIN) (2.9.4.5) SHAFT END: TAPERED CYLINDRICAL
14 TORSIONAL CRITICAL SPEEDS: MAX. YIELD STRENGTH (N)
15 FIRST CRITICAL RPM SHAFT HARDNESS (BNH)(Rc)
16 SECOND CRITICAL RPM MAX TORQUE CAPABILITY (N-m)
17 THIRD CRITICAL RPM BALANCE PISTON:
18 FOURTH CRITICAL RPM MATERIAL AREA (mm²)
19 VIBRATION: FIXATION METHOD
20 ALLOWABLE TEST LEVEL m SHAFT SLEEVES :
21 (PEAK TO PEAK) AT INTERSTG. CLOSE MATL
22 ROTATION, VIEWED FROM DRIVEN END CW CCW CLEARENCE POINTS
23 MATERIALS INSPECTION REQUIREMENTS (4.2.2) AT SHAFT SEALS MATL
24 SPECIAL CHARPY TESTING (2.11.3) ACCESSILBLE (2.8.2)
25 RADIOGRAPHY REQUIRED FOR LABYRINTHS:
26 ULTRASONIC REQUIRED FOR INTERSTAGE
27 MAGNETIC PARTICLE REQUIRED FOR TYPE MATERIAL
28 LIQUID PENETRANT REQUIRED FOR BALANCE PISTON
29 CASING: TYPE MATERIAL
30 MODEL SHAFT SEALS:
31 CASING SPLIT SEAL TYPE (2.8.3)
32 MATERIAL SETTLING OUT PRESSURE (BARG)(kPaG)
33 THICKNESS (mm) CORR. ALLOW. (mm) SPECIAL OPERATION (2.8.1)
34 MAX. WORKING PRESS (BARG)(kPaG) SUPPLEMENTAL DEVICE REQUIRED FOR CONTACT
35 MAX DESIGN PRESS (BARG)(kPaG) SEALS (2.8.3.2) TYPE
36 TEST PRESS (BARG)(kPaG): HELIUM HYDRO BUFFER GAS SYSTEM REQUIRED (2.8.7) MANIFOLD (3.5.1.6)
37 MAX OPER. TEMP. °C MIN. OPER. TEMP. °C TYPE BUFFER GAS
38 MAX NO. OF IMPELLERS FOR CASING BUFFER GAS CONTROL SYSTEM SCHEMATIC BY VENDOR
39 MAX CASING CAPACITY (m³/h) PRESSURIZING GAS FOR SUBATMOSPHERIC SEALS (2.8.8)
40 CASING SPLIT SEALING (2.2.10) TYPE SEAL
41 SYSTEM RELIEF VALVE SET PT. (2.2.4) (BARG)(kPaG) INNER OIL LEAKAGE GUAR. (l /DAY/SEAL)
42 DIAPHRAGMS: BUFFER GAS REQUIRED FOR:
43 MATERIAL AIR RUN-IN OTHER
44 IMPELLERS: BUFFER GAS FLOW (PER SEAL):
45 NO. DIAMETERS NORM: kg/MIN @ (BAR)(kPa) DP
46 NO. VANES EA. IMPELLER MAX. kg/MIN @ (BAR)(kPa) DP
47 BEARING HOUSING CONSTRUCTION:
48 TYPE (SEPARATE, INTEGRAL) SPLIT
49 MATERIAL
50
51
07/96 EF-050-90.09-M SHT 3 OF 6 API617SI.XLS REV 0
Brown & Root, Inc.
JOB NO. 0 ITEM NO.
CENTRIFUGAL COMPRESSOR REVISION NO. 0 DATE ###
DATA SHEET (API 617-6TH) PAGE 4 OF 6 BY 0
SI UNITS
1 CONSTRUCTION FEATURES (CONTINUED)
2 BEARINGS AND BEARING HOUSINGS
3 RADIAL INLET EXHAUST THRUST ACTIVE INACTIVE
4 TYPE TYPE
5 MANUFACTURER MANUFACTURER
6 LENGTH (mm) UNIT LOADING (MAX BAR)
7 SHAFT DIA. (mm) UNIT LOAD (ULT.) (BAR)
8 UNIT LOAD (ACT/ALLOW) AREA (mm²)
9 BASE MATERIAL NO. PADS
10 BABBIT THICKNESS (mm) PIVOT: CENTER / OFFSET, %
11 NO. PADS PAD BASE MATL
12 LOAD: B'TWN/ON PAD LUBRICATION: FLOODED DIRECTED
13 PIVOT: CTR/OFFSET, % THRUST COLLAR: INTEGRAL REPLACEABLE
14 MATERIAL
15 BEARING SPAN mm SEE ATTACHED API-670
16 BEARING TEMPERATURE DEVICES SEE ATTACHED VIBRATION DETECTORS: DATA SHEET
17 THERMISTORS API-670 DATA SHT TYPE MODEL
18 TYPE POS TEMP COEFF NEG TEMP COEFF MFR
19 TEMP SWITCH & INDICATOR BY: PURCH MFR NO. AT EA SHAFT BEARING TOTAL NO.
20 THERMOCOUPLES OSCILLATOR-DETECTORS SUPPLIED BY
21 SELECTOR SWITCH & INDIC. BY: PURCH MFR MFR MODEL
22 RESISTANCE TEMP DETECTORS MONITOR SUPPLIED BY (3.4.7.2)
23 RESISTANCE MAT'L OHMS LOCATION ENCLOSURE
24 SELECTOR SWITCH & INDICATOR BY: MFR. MODEL
25 PURCH MFR SCALE RGE ALARM SET @ m
26 LOCATION-JOURNAL BRG SHTDWN: SET @ m TIME DELAY SEC
27 NO. EA PAD EVERY OTH PAD PER BRG
28 OTHER AXIAL POSITION DETECTOR: SEE ATTACH. API-670
29 LOCATION-THRUST BRG DATA SHEET
30 NO. EA PAD EVERY OTH PAD PER BRG TYPE MODEL
31 OTHER MFR NO. REQUIRED
32 NO. (INACT) EA PAD EVERY OTH PAD PER BRG OSCILLATOR-DEMODULATOR SUPPLIED BY
33 OTHER MFR MODEL
34 MONITOR SUPPLIED BY (3.4.7.4) MONITOR SUPPLIED BY (3.4.7.2)
35 LOCATION ENCLOSURE LOCATION ENCLOSURE
36 MFR. MODEL MFR. MODEL
37 SCALE RGE ALARM SET @ °C SCALE RGE ALARM SET @ m
38 SHTDWN SET @ °C TIME DELAY SEC SHTDWN: SET @ m TIME DELAY SEC
39 CASING CONNECTIONS
40 DESIGN ASME
41 APPROVAL API605 FLANGED MATING FLG GAS
42 CONNECTION REQ'D OTHERS FACING POSITION OR & GASKET VELOCITY
43 (2.11.2.10) SIZE (2.4.2.1) STUDDED BY VENDOR m/SEC
44 (2.4.2.1) (2.4.2.3)
45 INLET
46 DISCHARGE
47
48
49
50
51
07/96 EF-050-90.09-M SHT 4 OF 6 API617SI.XLS REV 0
Brown & Root, Inc.
JOB NO. 0 ITEM NO.
CENTRIFUGAL COMPRESSOR REVISION NO. 0 DATE ###
DATA SHEET (API 617-6TH) PAGE 5 OF 6 BY 0
SI UNITS
1 OTHER CONNECTIONS ALLOWABLE PIPING FORCES AND MOMENTS:
2 SERVICE: NO. SIZE TYPE INLET DISCHARGE
3 LUBE-OIL INLET FORCE MOMT FORCE MOMT FORCE MOMT
4 LUBE OIL OUTLET N N-m N N-m N N-m
5 SEAL-OIL INLET AXIAL
6 SEAL-OIL OUTLET VERTICAL
7 SEAL GAS INLET HORIZ. 90
8 SEAL GAS OUTLET FORCE MOMT FORCE MOMT FORCE MOMT
9 CASING DRAINS N N-m N N-m N N-m
10 STAGE DRAINS AXIAL
11 VENTS VERTICAL
12 COOLING WATER HORIZ. 90
13 PRESSURE ACCELEROMETER(3.4.7.5)
14 TEMPERATURE SEE ATTACHED API-670 DATA SHEET
15 SOLVENT INJECTION TYPE MODEL
16 PURGE FOR: MFR NO. REQUIRED
17 BRG. HOUSING LOCATION
18 BTWN BRG & SEAL OSCILATOR-DEMODULATORS SUPPLIED BY
19 BTWN SEAL & GAS MFR MODEL
20 INDIVIDUAL STAGE DRAINS REQUIRED (2.4.3.2) MONITOR SUPPLIED BY (3.4.7.6)
21 VALVED & BLINDED LOCATION ENCLOSURE
22 VALVED & BLINDED & MANIFOLD MFR MODEL
23 KEY PHASOR REQUIRED SCALE RANGE ALARM SET @ mm/SEC²
24 COMPRESSOR GEAR DRIVER SHTDWN SET @ mm/SEC² TIME DELAY SEC
25 ACCESSORIES
26 COUPLING AND GUARDS (3.2)
27 NOTE: SEE ROTATING ELEMENTS - SHAFT ENDS
28 SEE ATTACHED API-671 DATA SHEET KEYLESS HYDRAULIC KEYED
29 COUPLING FURNISHED BY
30 MANUFACTURER TYPE MODEL
31 COUPLING GUARD FURNISHED BY:
32 TYPE: FULLY ENCLOSED SEMI-OPEN OTHER
33 COUPLING DETAILS VENDOR MOUNT HALF COUPLING
34 MAX O.D. mm LUBRICATION REQUIREMENTS:
35 HUB WEIGHT kg NON-LUBE GREASE CONT. OIL LUBE OTHER
36 SPACER LENGTH mm QUANTITY PER HUB kgs or L/MIN
37 SPACER WEIGHT kg
38 MOUNTING PLATES
39 BASEPLATES: FURNISHED BY (3.3.1.1) SOLEPLATES: FURNISHED BY:
40 COMPRESSOR ONLY (3.3.2.1) DRIVER GEAR THICKNESS mm
41 OTHER SUBSOLE PLATES REQ'D (3.3.3.2)
42 DRIP TRIM LEVELING PADS (3.3.2.2) STAINLESS STEEL SHIM THICKNESS - mm
43 COLUMN MOUNTING (3.3.2.3) DRIVER GEAR COMPRESSOR
44 SUB-SOLE PLATES REQ'D (3.3.3.2) PRIMER FOR EPOXY GROUT REQ'D (3.3.1.2.9)
45 STAINLESS STEEL SHIM THICKNESS mm TYPE
46 PRIMER FOR EPOXY GROUT REQ'D (3.3.1.2.9)
47 TYPE
48
49 BASE PLATE WILL BE ON CONCRETE FOUNDATION (3.3.2.5)
50 MACHINED MOUNTING PADS REQ'D. (3.3.2.6)
51
07/96 EF-050-90.09-M SHT 5 OF 6 API617SI.XLS REV 0
Brown & Root, Inc.
JOB NO. 0 ITEM NO.
CENTRIFUGAL COMPRESSOR REVISION NO. 0 DATE ###
DATA SHEET (API 617-6TH) PAGE 6 OF 6 BY 0
SI UNITS
1 UTILITIES
2 UTILITY CONDITIONS: TOTAL UTILITY CONSUMPTION:
3 STEAM: DRIVERS HEATING COOLING WATER m³/h
4 INLET MIN BARG(kPaG) °C BARG(kPaG) °C STEAM, NORMAL kg/h
5 NORM BARG(kPaG) °C BARG(kPaG) °C STEAM, MAX kg/h
6 MAX BARG(kPaG) °C BARG(kPaG) °C INSTRUMENT AIR m³/h
7 EXHAUST. MIN BARG(kPaG) °C BARG(kPaG) °C HP (DRIVER) kW
8 NORM BARG(kPaG) °C BARG(kPaG) °C HP (AUXILIARIES) kW
9 MAX BARG(kPaG) °C BARG(kPaG) °C HEATERS KW
10 ELECTRICITY: (3.4.6.1) PURGE (AIR OR N2) m³/h
11 DRIVERS HEATING CONTROL SHUTDOWN MISCELLANEOUS:
12 VOLTAGE RECOMMENDED STRAIGHT RUN OF PIPE DIAMETERS
13 HERTZ BEFORE SUCTION
14 PHASE NOMOGRAPHS REQUIRED FOR EACH SECTION (5.3.3.1.5)
15 COOLING WATER: VENDOR'S REVIEW & COMMENTS ON PURCHASER'S
16 TEMP. INLET °C MAX RETURN °C PIPING & FOUNDATION (3.5.3.2)
17 PRESS NORM BARG(kPaG ) COMPRESSOR TO BE SUITABLE FOR FIELD RUN IN
18 DESIGN BARG(kPaG) ON AIR (2.1.17)
19 MIN RETURN BARG(kPaG) PROVISION FOR LIQUID INJECTION (2.1.11)
20 MAX ALLOW D P BAR(kPa)
21 WATER SOURCE VENDOR'S REVIEW & COMMENTS ON PURCHASER'S
22 INSTRUMENT AIR: CONTROL SYSTEMS (3.4.1.1)
23 MAX PRESS BARG(kPaG) MIN PRESS BARG(kPaG) EXTENT OF PROCESS PIPING BY VENDOR (3.5.3.1)
24 SHOP INSPECTION AND TESTS: (4.1.4) REQ'D. SHOP FITUP OF VENDOR PROCESS PIPING (4.4.3.11)
25 CLEANLINES (4.2.1.5) WELDING HARDNESS TESTING (4.2.1.6)
26 HYDROSTATIC X
2
27 IMPELLER OVERSPEED X VENDOR'S REPRESENTATIVE SHALL (2.1.14)
28 MECHANICAL RUN X OBSERVE FLANGE PARTING
29 CONTRACT COUPLING IDLING ADAPTORS CHECK ALIGNMENT AT TEMPERATURE
30 CONTRACT PROBES SHOP PROBES BE PRESENT AT INITIAL ALIGNMENT
31 VARY LUBE & SEAL OIL PRESSURES WEIGHTS (kg):
32 AND TEMPERATURES (4.3.4.2.5) COMPR. GEAR DRIVER BASE
33 POLAR FORM VIB DATA (4.3.4.3.3) ROTORS: COMPR. DRIVER GEAR
34 TAPE RECORD VIB DATA (4.3.4.3.6) COMPRESSOR UPPER CASE
35 TAPE DATA TO PURCHASER (4.3.4.3.7) SOUR SEAL OIL TRAPS
36 SHAFT END SEAL INSP (4.3.4.4.1) L.O. CONSOLE S.O. CONSOLE
37 GAS LEAK TEST DISCH PRESS (4.3.5.2) OVERHEAD SEAL OIL TANKS
38 BEFORE AFTER POST TEST INSPECTION (4.3.6.8) MAX. FOR MAINTENANCE (IDENTIFY)
39 PERFORMANCE TEST(GAS)(AIR)(4.3.6.1) TOTAL SHIPPING WEIGHT
40 COMPLETE UNIT TEST (4.3.6.2)
41 TORSIONAL VIB MEAS (4.3.6.2) SPACE REQUIREMENTS (mm):
42 TANDEM TEST (4.3.6.3) COMPLETE UNIT: L W H
43 GEAR TEST (4.3.6.4) L.O. CONSOLE: L W H
44 HELIUM LEAK TEST (4.3.6.5) S.O. CONSOLE: L W H
45 SOUND LEVEL TEST (4.3.6.6) SOUR SEAL OIL TRAPS
46 FULL LOAD / SPEED / PRESS TEST (4.3.6.9) OVERHEAD SEAL OIL TANKS
47 HYDRAULIC COUPLING INSP (4.3.6.10)
48 REMARKS:
49
50
51
07/96 EF-050-90.09-M SHT 6 OF 6 API617SI.XLS REV 0
