Scribd
Upload
84 views

quiz2F-KEY

Uploaded by

marlouimperial36
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
84 views

quiz2F-KEY

Uploaded by

marlouimperial36
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 1

Quiz #2F

1. A 6-pole , 3-phase, 50 Hz induction motor runs on full load with a slip of 5%. If the motor standstill impedance is ( 0.015 + j0.075)
ohms, then the available maximum torque is approximately___% of full load torque.
a. 188 b. 223 c. 212 d. 198
2. If the starting torque of a 7.5 hp, 440 volt, 1730 rpm motor is 2 ½ times its rated full load torque when rated voltage is
impressed, calculate the starting torque when 230 volts is applied at the instant the motor is started.
a. 15.55 lb-ft b. 14.23 lb-ft c. 12.12 lb-ft d. 16.42 lb-ft
3. A 1100-V, 50 Hz delta-connected induction motor has a star connected slip ring rotor with a phase transformation ratio of 3.8.
The rotor resistance and standstill reactance are 0.012 ohms and 0.25 ohms per phase respectively. Neglecting stator
impedance and magnetizing current, determine the rotor current at 4% slip with the slip rings shorted.
a. 674 A b. 713 A c. 741 A d. 692 A
4. A 60 Hz induction motor has a speed of 1740 rpm when fully loaded; what is the speed when the load is removed?
a. 3600 rpm b. 2000 rpm c. 1800 rpm d. 1740 rpm
5. Calculate the torque developed per phase by a 6-phase , 60 Hz, 3-phase induction motor at a slip of 5%, if the motor develops a
maximum per phase torque of 300 N-m, while running at 780 rpm. The rotor leakage reactance is 3 ohms per phase.
a. 90 N-m b. 84 N-m c. 88 n-m d. 86 N-m
6. An induction motor has an output of 30 KW at 86 % efficiency. For this operating condition, stator copper loss = rotor copper
loss = core losses = mechanical rotational losses. Determine the slip.
a. 3.76 % b. 3.27 % c. 3.08% d. 3.45 %
7. The input to the rotor circuit of a 4-poles, 60 Hz induction motor running at 1000 rpm, is 3 KW. What is the rotor copper loss?
a. 2400 watts b. 1666 watts c. 1333 watts d. 1800 watts
8. A certain 3-phase, induction motor when fully loaded runs with a slip of 3%. Find the value of the resistance necessary in series
per phase of the rotor to reduce the speed by 10%. Assume that the resistance of the rotor per phase is 0.2 ohm.
a. 0.65 ohms b. 1.18 ohms c. 1.26 ohms d. 0.88 ohms
9. An induction motor carries a rotor current per phase of 10 A when loaded until the slip is 5%. If the rotor effective resistance is
0.1 ohm per phase, determine the internal power developed per phase.
a. 190 W b. 180 W c. 200 W d. 120 W
10. The power input to the rotor of a 440-V, 50 Hz, 6-pole, 3-phase induction motor is 100 KW. The rotor electromotive force is
observed to make 120 cycles per minute. Calculate the speed of stator field with respect to rotor.
a. 40 rpm b. 80 rpm c. 60 rpm d. 100 rpm
11. A slip ring induction motor runs at 290 rpm on full load when connected to a 50 Hz supply. Calculate the slip for full load torque
if the total resistance of then rotor circuit is doubled.
a. 4.2 % b. 5.1 % c. 3.8 % d. 6.6 %
12. An induction motor is running at 50% of the synchronous speed with a useful output of 55 hp and the mechanical losses total 2
hp. Estimate the copper loss in the rotor circuit?
a. 42.52 KW b. 40.34 KW c. 43.22 KW d. 45.46 KW
13. An induction motor has a starting current 7 times the full load current and a full load slip of 4%. Its line starting torque is
___times the full load torque.
a. 7 b. 4 c. 1.96 d. 49
14. The power input to the rotor of a 440-V, 50-Hz, 3-phase, 6-pole induction motor is 60 KW. It is observed that the rotor emf
makes 90 complete cycles per minute. Calculate the mechanical power developed.
a. 58.2 KW b. 56.4 KW c. 55.5 KW d. 59.2 KW
15. An 8-pole, three-phase 50-cycle induction motor is taking 50 KW and running at 725 rpm. The stator losses and frictional losses
amount to 1.2 KW and 1.8 KW. Determine motor bhp.
a. 63.28 hp b. 62.35 hp c. 60.82 hp d. 64.54 hp

You might also like