DMM4040 and

DMM4050
Digital Multimeter

Users Manual

077-0361-00
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix
or its subsidiaries or suppliers, and are protected by national copyright laws and international
treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in
this publication supersedes that in all previously published material. Specifications and price
change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix, Inc.

Tektronix, Inc.
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA

For product information, sales, service, and technical support:

- In North America, call 1-800-833-9200.
- Worldwide, visit www.tektronix.com to find contacts in your area.
 Warranty
Tektronix warrants that the product will be free from defects in materials and workmanship for a period of
three (3) years from the date of original purchase from an authorized Tektronix distributor. If the product
proves defective during this warranty period, Tektronix, at its option, either will repair the defective product
without charge for parts and labor, or will provide a replacement in exchange for the defective product.
Batteries are excluded from this warranty. Parts, modules and replacement products used by Tektronix for
warranty work may be new or reconditioned to like new performance. All replaced parts, modules and
products become the property of Tektronix.
In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the
expiration of the warranty period and make suitable arrangements for the performance of service. Customer
shall be responsible for packaging and shipping the defective product to the service center designated by
Tektronix, shipping charges prepaid, and with a copy of customer proof of purchase. Tektronix shall pay for
the return of the product to Customer if the shipment is to a location within the country in which the Tektronix
service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and
any other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or
inadequate maintenance and care. Tektronix shall not be obligated to furnish service under this warranty
a) to repair damage resulting from attempts by personnel other than Tektronix representatives to install,
repair or service the product; b) to repair damage resulting from improper use or connection to incompatible
equipment; c) to repair any damage or malfunction caused by the use of non-Tektronix supplies; or d) to
service a product that has been modified or integrated with other products when the effect of such
modification or integration increases the time or difficulty of servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY
OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
TEKTRONIX' RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND
EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY.
TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS
ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
[W16 – 15AUG04]
 Table of Contents

Chapter Title Page

1 Introduction and Specifications......................................................... 1-1

General Safety Summary ................................................................................... 1-3
Compliance Information .................................................................................... 1-8
EMC Compliance .......................................................................................... 1-8
Safety Compliance......................................................................................... 1-9
Environmental Considerations........................................................................... 1-10
Product End-of-Life Handling....................................................................... 1-10
Introduction........................................................................................................ 1-11
User Documentation .......................................................................................... 1-12
About this Manual ............................................................................................. 1-12
Instrument Security Procedures ......................................................................... 1-13
Volatile Memory ........................................................................................... 1-13
Non Volatile Memory.................................................................................... 1-13
Media Memory .............................................................................................. 1-14
Accessories ........................................................................................................ 1-14
General Specifications ....................................................................................... 1-15
Power............................................................................................................. 1-15
Dimensions .................................................................................................... 1-15
Display........................................................................................................... 1-15
Environment .................................................................................................. 1-15
Triggering ...................................................................................................... 1-15
Memory ......................................................................................................... 1-15
Math Functions.............................................................................................. 1-15
Electrical........................................................................................................ 1-15
Remote Interfaces .......................................................................................... 1-16
Warranty ........................................................................................................ 1-16
Electrical Specifications .................................................................................... 1-16
DC Voltage Specifications ............................................................................ 1-16
AC Voltage Specifications ............................................................................ 1-17
Resistance ...................................................................................................... 1-19
DC Current .................................................................................................... 1-20
AC Current .................................................................................................... 1-22
Frequency ...................................................................................................... 1-24
Capacitance (4050 Only)............................................................................... 1-25
Temperature (4050 only)............................................................................... 1-25

i
DMM4040 and DMM4050
Users Manual

Additional Errors ........................................................................................... 1-25

Continuity ...................................................................................................... 1-25
Diode Test ..................................................................................................... 1-26
Measurement Rates (IEEE488[4])................................................................. 1-26

2 Preparing the Meter for Operation ..................................................... 2-1

Introduction........................................................................................................ 2-3
Unpacking and Inspecting the Meter ................................................................. 2-3
Storing and Shipping the Meter ......................................................................... 2-3
Power Considerations ........................................................................................ 2-3
Selecting the Line Voltage ............................................................................ 2-3
Replacing the Fuses....................................................................................... 2-4
Connecting to Line Power ................................................................................. 2-6
Turning Power-On ............................................................................................. 2-7
Adjusting the Bail .............................................................................................. 2-7
Installing the Meter in an Equipment Rack ....................................................... 2-8
Cleaning the Meter............................................................................................. 2-8
Fluke 45 Emulation Mode ................................................................................. 2-8

3 Front-Panel Operation ........................................................................ 3-1

Introduction........................................................................................................ 3-3
Controls and Indicators ...................................................................................... 3-4
Front-Panel Feature Descriptions .................................................................. 3-4
Display Panel................................................................................................. 3-5
Rear-Panel Connectors .................................................................................. 3-7
Adjusting the Meter’s Range......................................................................... 3-8
Navigating the Front-Panel Menu...................................................................... 3-8
Configuring the Meter for a Measurement ........................................................ 3-8
Setting the Beeper State................................................................................. 3-8
Setting the Display Resolution ...................................................................... 3-9
Setting the AC Signal Filter .......................................................................... 3-9
Setting Continuity Resistance Threshold and Diode Test Parameters .......... 3-10
Setting the Default Temperature Scale (4050 Only) ..................................... 3-10
Enabling High Input Impedance.................................................................... 3-10
Using the Analyze Functions ............................................................................. 3-11
Collecting Statistics on Measurements.......................................................... 3-11
Testing Using Limits ..................................................................................... 3-12
Setting an Offset Value ................................................................................. 3-13
Using MX+B ................................................................................................. 3-13
Using TrendPlot............................................................................................. 3-14
Using the Histogram Function....................................................................... 3-16
Controlling Trigger Functions ........................................................................... 3-16
Choosing a Trigger Source ............................................................................ 3-17
Setting the Trigger Delay .............................................................................. 3-18
Setting the Number of Samples ..................................................................... 3-18
Understanding the Measurement Complete Signal ....................................... 3-18
Accessing and Controlling Memory.............................................................. 3-18
Storing Readings in Memory......................................................................... 3-19
Recalling Readings from Memory ................................................................ 3-20
Storing Meter Configuration Information ..................................................... 3-21
Storing the Power-up Configuration.............................................................. 3-22
Recalling the Power-up Configuration .......................................................... 3-22
Removing the Power-up Configuration......................................................... 3-22
Recalling a Meter Configuration ................................................................... 3-23
ii
 Contents (continued)

Managing Memory ........................................................................................ 3-23

Controlling System-Related Operations ............................................................ 3-24
Identifying Meter Errors................................................................................ 3-24
Querying the Firmware for Revision Level................................................... 3-24
Adjusting Display Brightness........................................................................ 3-25
Setting the Meter’s Date and Time................................................................ 3-25
USB Operation .............................................................................................. 3-25
USB Storage Capacity and Write Time......................................................... 3-25
USB Memory Device Compatibility and Special Instruction ....................... 3-26
Configuring the Remote Interface ..................................................................... 3-26
Sample Program Using the RS-232 Computer Interface ................................... 3-26
Checking the Meter’s Calibration Date ............................................................. 3-28
Resetting the Meter’s Default Settings .............................................................. 3-28

4 Making Measurements ........................................................................ 4-1

Introduction........................................................................................................ 4-3
Selecting Function Modifiers............................................................................. 4-3
Activating the Secondary Display ..................................................................... 4-3
Measuring Voltage............................................................................................. 4-4
Measuring DC Voltage.................................................................................. 4-4
Measuring AC Voltage.................................................................................. 4-6
Measuring Frequency and Period ...................................................................... 4-7
Measuring Resistance ........................................................................................ 4-8
Making a Two-wire Resistance Measurement .............................................. 4-8
Making a Four-wire Resistance Measurement .............................................. 4-9
Measuring Current ............................................................................................. 4-10
Measuring DC Current .................................................................................. 4-12
Measuring AC Current .................................................................................. 4-13
Measuring Capacitance (4050 only) .................................................................. 4-14
Measuring RTD Temperature (4050 only) ........................................................ 4-15
Testing Continuity ............................................................................................. 4-16
Checking Diodes................................................................................................ 4-17
Making a Triggered Measurement..................................................................... 4-18
Setting the Trigger Mode............................................................................... 4-18
Setting a Trigger Delay ................................................................................. 4-19
Setting Number of Samples per Trigger........................................................ 4-19
Connecting an External Trigger .................................................................... 4-19
Monitoring the Measurement-Complete Signal................................................. 4-20

Appendices
A 2X4 Test Leads............................................................................................ A-1
B Errors........................................................................................................... B-1
C RS-232 Port Connections ............................................................................ C-1
D Analog Filter Applications .......................................................................... D-1

Index

iii
DMM4040 and DMM4050
Users Manual

iv
 List of Tables

Table Title Page

1-1. Volatile Memory Space.......................................................................................... 1-13

1-2. Non-volatile Memory Space .................................................................................. 1-13
1-3. Accessories............................................................................................................. 1-14
2-1. Line Voltage to Fuse Rating................................................................................... 2-5
2-2. Line-Power Cord Types Available from Tektronix ............................................... 2-7
3-1. Front-Panel Controls and Connectors .................................................................... 3-4
3-2. Display Elements ................................................................................................... 3-6
3-3. Rear-Panel Connectors........................................................................................... 3-7

v
DMM4040 and DMM4050
Users Manual

vi
 List of Figures

Figure Title Page

1-1. IEC 61010 Measurement Category (CAT) Levels................................................. 1-7

2-1. Replacing the Line Fuse......................................................................................... 2-5
2-2. Replacing the Current Input Fuses ......................................................................... 2-6
2-3. Bail Adjustment and Removal ............................................................................... 2-8
3-1. TrendPlot Display .................................................................................................. 3-15
3-2. Histogram Display ................................................................................................. 3-16
3-3. Sample Program for RS-232 Computer Interface .................................................. 3-27
4-1. Input Connections for Voltage, Resistance, and Frequency Measurements .......... 4-4
4-2. Input Connections for 4-wire Resistance Measurements ....................................... 4-9
4-3. Input Connections for 4-wire Ohms Using 2x4 Wire Leads.................................. 4-10
4-4. Input Connections for Current Measurements Below 400 mA .............................. 4-11
4-5. Input Connections for Current Measurements Above 400 mA.............................. 4-11
4-6. Measuring Capacitance .......................................................................................... 4-15
4-7. Temperature Measurements ................................................................................... 4-15
4-8. Diode Testing Connections .................................................................................... 4-18
4-9. TRIG I/O Pin-out Description................................................................................ 4-19

vii
DMM4040 and DMM4050
Users Manual

viii
 Chapter 1
Introduction and Specifications

Title Page

General Safety Summary ..................................................................................... 1-3

Compliance Information ...................................................................................... 1-8
EMC Compliance ............................................................................................ 1-8
Safety Compliance........................................................................................... 1-9
Environmental Considerations............................................................................. 1-10
Product End-of-Life Handling......................................................................... 1-10
Introduction.......................................................................................................... 1-11
User Documentation ............................................................................................ 1-12
About this Manual ............................................................................................... 1-12
Instrument Security Procedures ........................................................................... 1-13
Volatile Memory ............................................................................................. 1-13
Non Volatile Memory...................................................................................... 1-13
Media Memory ................................................................................................ 1-14
Accessories .......................................................................................................... 1-14
General Specifications ......................................................................................... 1-15
Power............................................................................................................... 1-15
Dimensions ...................................................................................................... 1-15
Display............................................................................................................. 1-15
Environment .................................................................................................... 1-15
Triggering ........................................................................................................ 1-15
Memory ........................................................................................................... 1-15
Math Functions................................................................................................ 1-15
Electrical.......................................................................................................... 1-15
Remote Interfaces ............................................................................................ 1-16
Warranty .......................................................................................................... 1-16
Electrical Specifications ...................................................................................... 1-16
DC Voltage Specifications .............................................................................. 1-16
AC Voltage Specifications .............................................................................. 1-17
Resistance ........................................................................................................ 1-19
DC Current ...................................................................................................... 1-20
AC Current ...................................................................................................... 1-22
Frequency ........................................................................................................ 1-24
Capacitance (4050 Only)................................................................................. 1-25
Temperature (4050 only)................................................................................. 1-25
Additional Errors ............................................................................................. 1-25

1-1
DMM4040/4050
Users Manual

Continuity ........................................................................................................ 1-25

Diode Test ....................................................................................................... 1-26
Measurement Rates (IEEE488[4])................................................................... 1-26

1-2
 Introduction and Specifications
General Safety Summary 1
General Safety Summary

Review the following safety precautions to avoid injury and prevent damage to this
product or any other products connected to it.
To avoid potential hazards, use this product only as specified.
Only qualified personnel should perform service procedures.
While using this product, you may need to access other parts of a larger system. Read the
safety sections of the other component manuals for warnings and cautions related to
operating the system.
This instrument has been designed and tested in accordance with the European standard
publication EN 61010-1:2001 and U.S./Canadian standard publications UL 61010-1 and
CAN/CSA-C22.2 No.61010-1-04. The instrument has been supplied in a safe condition.
This manual contains information and warnings that must be observed to keep the
instrument in a safe condition and ensure safe operation.
To use the instrument correctly and safely, read and follow the precautions in this section
and follow all the safety instructions or warnings given throughout this manual that relate
to specific measurement functions. In addition, follow all generally accepted safety
practices and procedures required when working with and around electricity.
CAT I equipment is designed to protect against transients from high-voltage, low-energy
sources, such as electronic circuits or a copy machine.
CAT II equipment is designed to protect against transients from energy-consuming
equipment supplied from the fixed installtion, such as TVs, PCs, portable tools, and other
houseshold appliances.

To Avoid Fire or Personal Injury

Use Proper Power Cord. Use only the power cord specified for this product and
certified for the country of use.
Use Proper Voltage Setting. Before applying power, ensure that the line selector is in
the proper position for the source being used.
Connect and Disconnect Properly. Do not connect or disconnect probes or test
leads while they are connected to a voltage source.
Ground the Product. This product is grounded through the grounding conductor of the
power cord. To avoid electric shock, the grounding conductor must be connected to earth
ground. Before making connections to the input or output terminals of the product, ensure
that the product is properly grounded.
Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings
and markings on the product. Consult the product manual for further ratings information
before making connections to the product.
Do not apply a potential to any terminal, including the common terminal, that exceeds the
maximum rating of that terminal.
Power Disconnect. The power cord disconnects the product from the power source. Do
not block the power cord; it must remain accessible to the user at all times.
Do Not Operate Without Covers. Do not operate this product with covers or panels
removed.

1-3
DMM4040/4050
Users Manual

Do Not Operate With Suspected Failures. If you suspect that there is damage to this
product, have it inspected by qualified service personnel.
Avoid Exposed Circuitry. Do not touch exposed connections and components when
power is present.
Use Proper Fuse. Use only the fuse type and rating specified for this product.
Keep Product Surfaces Clean and Dry.

XW Warning
To avoid possible electric shock, personal injury, or death, read
the following before using the Meter.
• Use the Meter only as specified in this manual, or the
protection provided by the Meter might be impaired.
• Do not use the Meter in wet environments.
• Inspect the Meter before using it. Do not use the Meter if it
appears damaged.
• Inspect the test leads before use. Do not use them if
insulation is damaged or metal is exposed. Check the test
leads for continuity. Replace damaged test leads before
using the Meter.
• Verify the Meter's operation by measuring a known voltage
before and after using it. Do not use the Meter if it operates
abnormally. Protection may be impaired. If in doubt, have
the Meter serviced.
• Whenever it is likely that safety protection has been
impaired, make the Meter inoperative and secure it against
any unintended operation.
• Servicing of the Meter should be performed by qualified
service personnel.
• Do not apply more than the rated voltage, as marked on the
Meter, between the terminals or between any terminal and
earth ground.
• While in IEC Measurement Category II environments, do not
apply voltages above 600 V ac to the input of the Meter. See
“Description of IEC 61010 Measurement Categories” later in
this manual.
• Always use the power cord and connector appropriate for
the voltage and outlet of the country or location in which
you are working.
• Always use a power cord with a ground connection and
ensure the ground is properly connected to the power
distribution system.
• Remove test leads from the Meter before opening the case.
• Never remove the cover or open the case of the Meter
without first removing it from the main power source.

1-4
 Introduction and Specifications
General Safety Summary 1
• Use caution when working with voltages above 30 V ac rms,
42 V ac peak, or 42 V dc. These voltages pose a shock
hazard.
• Use only the replacement fuse(s) specified by the manual.
• Use the proper terminals, function, and range for your
measurements.
• Do not operate the Meter around explosive gas, vapor, or
dust.
• When using probes, keep your fingers behind the finger
guards.
• When making electrical connections, connect the common
test lead before connecting the live test lead; when
disconnecting, disconnect the live test lead before
disconnecting the common test lead.
• Disconnect circuit power and discharge all high-voltage
capacitors before testing resistance, continuity, diodes, or
capacitance.
• Before measuring current, check the Meter's fuses and turn
OFF power to the circuit before connecting the Meter to the
circuit.
• When servicing the Meter, use only specified replacement
parts.
• To prevent damage to the Meter, do not change the position
of the Front/Rear switch while signals are applied to either
the front or rear input terminals.

1-5
DMM4040/4050
Users Manual

Symbols and Terms

The following terms and safety and electrical symbols may appear in the manual or on
the product:
A XW Warning statement identifies conditions or practices that could result in injury
or death.
A W Caution statement identifies conditions or practices that could result in damage to
the Meter or equipment to which it is connected.

XW Warning
To avoid electric shock, personal injury, or death, carefully read
the information under “General Safety Summary” before
attempting to install, use, or service the Meter.

Safety and Electrical Symbols

Symbol Description Symbol Description

Risk of danger. Important

W information. See manual.
P Display ON / OFF and Meter reset.

Hazardous voltage. Voltage > 30 V

X dc or ac peak might be present.
J Earth ground

B AC (Alternating Current) E Capacitance

F DC (Direct Current) G Diode

D
AC or DC (Alternating or Direct
or
Current)
I Fuse

C
Continuity test or continuity beeper
R tone
Y Digital signal

Y Potentially hazardous voltage U Maintenance or Service

Static awareness. Static discharge

T Double insulated h can damage parts.

Measurement Category II is for

Measurement Category I is for
measurements performed on
CAT II circuits directly connected to the
CAT I measurements not directly
connected to mains.
low voltage installation.

1-6
 Introduction and Specifications
General Safety Summary 1
Description of IEC 61010 Measurement Categories
The IEC 61010 safety standard defines four Overvoltage (Installation) Categories (CAT I
to CAT IV) based on the magnitude of danger from transient impulses as shown in Figure
1-1.

CAT I CAT II CAT III CAT IV

Electronic Appliances, MC Panels, etc.
PCs, TVs

Service
Entrance
Meter

Service
Entrance Outbuilding
Meter

Underground Service

Service Transformer Outbuilding

Entrance
Meter

Underground Service

cat_levels.eps
Figure 1-1. IEC 61010 Measurement Category (CAT) Levels

The IEC 61010 Measurement CAT level indicates the level of protection the instrument
provides against impulse withstand voltage.
CAT I equipment is designed to protect against transients from high-voltage, low-energy
sources, such as electronic circuits or a copy machine.
CAT II equipment is designed to protect against transients from energy-consuming
equipment supplied from the fixed installation, such as TVs, PCs, portable tools, and
other household appliances.
CAT III equipment is designed to protect against transients in equipment in fixed
equipment installations, such as distribution panels, feeders and short branch circuits, and
lighting systems in large buildings.
CAT IV equipment is designed to protect against transients from the primary supply
level, such as an electricity meter or an overhead or underground utility service.

1-7
DMM4040/4050
Users Manual

Compliance Information
This section lists the EMC (electromagnetic compliance), safety, and environmental
standards with which the instrument complies.

EMC Compliance

EC Declaration of Conformity—EMC
Meets intent of Directive 2004/108/EC for Electromagnetic Compatibility. Compliance
was demonstrated to the following specifications as listed in the Official Journal of the
European Communities:

EN 61326-1 2006, EN 61326-2 2006. EMC requirements for electrical equipment for
measurement, control, and laboratory use. 1, 2, 3

ƒ CISPR 11:2003. Radiated and conducted emissions, Group 1, Class A

ƒ IEC 61000-4-2:2001. Electrostatic discharge immunity
ƒ IEC 61000-4-3:2002. RF electromagnetic field immunity 4
ƒ IEC 61000-4-4:2004. Electrical fast transient/burst immunity
ƒ IEC 61000-4-5:2001. Power line surge immunity
ƒ IEC 61000-4-6:2003. Conducted RF immunity 5
ƒ IEC 61000-4-11:2004. Voltage dips and interruptions immunity 6, 7

EN 61000-3-2:2006. AC power line harmonic emissions.

EN 61000-3-3:1995. Voltage changes, fluctuations, and flicker.

European Contact.

Tektronix UK, Ltd.

Western Peninsula
Western Road
Bracknell, RG12 1RF
United Kingdom

1
This product is intended for use in nonresidential areas only. Use in residential areas may cause electromagnetic
interference.
2
Emissions which exceed the levels required by this standard may occur when this equipment is connected to a test
object.
3
To ensure compliance with the EMC standards listed here, high quality shielded interface cables should be used.
4
The tolerance of the 100uADC, 10mADC ranges while subjected to the test field (3 V/m over the frequency range
of 80 MHz to 1 GHz, 1.4 GHz to 2.0 GHz, and 1V/m from 2.0 GHz to 2.7 GHz, with 80% amplitude modulation
at 1 kHz) can increase by +/- (0.06% of range) over the frequency range of 1.7 - 1.9GHz. (IEC 61000-4-3).
5
The tolerance of the 100uADC, 10mADC ranges while subjected to the injected test signal (3 V rms over the
frequency range of 150 kHz to 80 MHz, with 80% amplitude modulation at 1 kHz) can increase by +/- (0.08% of
range) at the frequency range of 20 - 50MHz. (IEC 61000-4-6).
6
Performance Criterion C applied at the 70%/25 cycle Voltage-Dip and the 0%/250 cycle Voltage-Interruption test
levels (IEC 61000-4-11).
7
Instrument rebooting may be experienced where the EUT takes approximately 18 seconds to recover from IEC
61000-4-11 transient immunity test.

1-8
 Introduction and Specifications
Compliance Information 1
Australia / New Zealand Declaration of Conformity – EMC
Complies with the EMC provision of the Radiocommunications Act per the following
standard, in accordance with ACMA:
CISPR 11:2003. Radiated and Conducted Emissions, Group 1, Class A, in accordance
with EN 61326-1:2006 and EN 61326-2-1:2006.

Safety Compliance

EC Declaration of Conformity – Low Voltage

Compliance was demonstrated to the following specification as listed in the Official
Journal of the European Communities:
Low Voltage Directive 2006/95/EC.
ƒ EN 61010-1: 2001. Safety requirements for electrical equipment for
measurement control and laboratory use.

U.S Nationally Recognized Testing Laboratory Listing

ƒ ISA-82.02.01. Safety Standard for Electrical and Electronic Test, Measuring,
Controlling and Related Equipment -- General Requirements.

Canadian Certification
ƒ CAN/CSA-C22.2 No. 61010-1:2004. Safety requirements for electrical
equipment for measurement, control, and laboratory use. Part 1.

Additional Compliances
ƒ IEC 61010-1: 2001. Safety requirements for electrical equipment for
measurement, control, and laboratory use.
ƒ ANSI/UL 61010-1:2004, 2nd Edition. Standard for electrical measuring and
test equipment.

Equipment Type
Test and measuring.

Safety Class
Class 1 — grounded product.

Pollution Degree Description

A measure of the contaminants that could occur in the environment around and within a
product. Typically the internal environment inside a product is considered to be the same
as the external. Products should be used only in the environment for which they are rated.
ƒ Pollution Degree 1. No pollution or only dry, nonconductive pollution occurs.
Products in this category are generally encapsulated, hermetically sealed, or
located in clean rooms.
ƒ Pollution Degree 2. Normally only dry, nonconductive pollution occurs.
Occasionally a temporary conductivity that is caused by condensation must be
expected. This location is a typical office/home environment. Temporary
condensation occurs only when the product is out of service.

1-9
DMM4040/4050
Users Manual

ƒ Pollution Degree 3. Conductive pollution, or dry, nonconductive pollution that

becomes conductive due to condensation. These are sheltered locations where
neither temperature nor humidity is controlled. The area is protected from direct
sunshine, rain, or direct wind.
ƒ Pollution Degree 4. Pollution that generates persistent conductivity through
conductive dust, rain, or snow. Typical outdoor locations.

Pollution Degree
Pollution Degree 2 (as defined in IEC 61010-1). Note: Rated for indoor use only.

Measurement Overvoltage Categories

CAT I – 1000V / CAT II – 600V

Environmental Considerations
This section provides information about the environmental impact of the product.

Product End-of-Life Handling

Observe the following guidelines when recycling an instrument or component:

Equipment Recycling
Production of this equipment required the extraction and use of natural resources. The
equipment may contain substances that could be harmful to the environment or human
health if improperly handled at the product’s end of life. In order to avoid release of such
substances into the environment and to reduce the use of natural resources, we encourage
you to recycle this product in an appropriate system that will ensure that most of the
materials are reused or recycled appropriately.

This symbol indicates that this product complies with the applicable European Union
requirements according to Directives 2002/96/EC and 2006/66/EC on waste electrical
and electronic equipment (WEEE) and batteries. For information about recycling options,
check the Support/Service section of the Tektronix Web site (www.tektronix.com).

Restriction of Hazardous Substances

This product has been classified as Monitoring and Control equipment, and is outside the
scope of the 2002/95/EC RoHS Directive.

Perchlorate Materials
This product contains one or more type CR lithium batteries. According to the state of
California, CR lithium batteries are classified as perchlorate materials and require special
handling. See www.dtsc.ca.gov/hazardouswaste/perchlorate for additional information.

1-10
 Introduction and Specifications
Introduction 1
Introduction
The DMM4040 and DMM4050 are 6-1/2 digit, dual-display multimeters designed for
bench-top, field service, and system applications. Their full complement of measurement
functions plus its RS-232, IEEE 488, and Ethernet Remote Interfaces makes these
multimeters ideal candidates for precision manual measurements and use in automated
systems. For portability, these multimeters include a carrying handle that also serves as a
bail for bench top operation.
There are a few feature differences between these two multimeters, and some
specifications are tighter for the DMM4050. Features that exist in only one multimeter
will be identified with the addition of “4050 Only” by each feature that is found only in
that model. Separate specification tables are also used to clarify the differences between
these two models.
The following is a list of some of the features and functions:
• Bright, large-digit, wide-viewing-angle display
• Dual display for displaying two properties of an input signal (e.g., ac voltage in one
display and frequency in the other).
• Remote operation via IEEE 488, RS-232, and Ethernet interface.
• Trigger in and measurement-complete out
• Front panel USB port for optional memory
• 6-1/2 digit resolution
• Half-rack width
• True rms ac
• 2 and 4-wire resistance measurements
• Extended 10 Ω and 1 GΩ ranges
• Frequency measurements to 1 MHz
• Capacitance measurements (4050 Only)
• Temperature measurement (4050 Only)
• 10 A current capability
• Decibels (dB and dBm) with variable reference impedance and audio power
measurement capability
• Input terminals on both front and rear panels of the meter
• Closed-case calibration (no internal calibration adjustments)

1-11
DMM4040/4050
Users Manual

User Documentation
The user documentation for this Meter includes the following:
Accessory Where to find Part number

Safety and Installation Instructions 071-2693-xx

+ +
Technical Reference 077-0362-xx
(Specifications and Performance
Verification)
+

Programmers Manual 077-0363-xx

Users Manual
(This manual)
Available in the following languages: +
English 077-0361-xx
French 077-0366-xx
Italian 077-0367-xx
German 077-0368-xx
Spanish 077-0370-xx
Japanese 077-0371-xx
S. Chinese 077-0372-xx
T. Chinese 077-0373-xx
Korean 077-0374-xx
Russian 077-0375-xx

About this Manual

This is the Users Manual for the DMM4040 and DMM4050 Digital Multimeters
(hereafter referred to as the Meter). It contains all of the information a new user will need
to operate the Meter effectively. The manual is divided into the following chapters:
Chapter 1 “Introduction and Specifications” provides information on how to safely
use the Meter, standard and optional accessories, and specifications.
Chapter 2 “Preparing for Operation” provides information on setting the Meter’s line
voltage, connecting it to a power source, and turning the Meter on.
Chapter 3 “Front Panel Operation” introduces the controls and connections on the
front and rear panels of the Meter.
Chapter 4 “Making Measurements” provides detailed information on using the Meter
to make electrical measurements.
Appendices

1-12
 Introduction and Specifications
Instrument Security Procedures 1
Instrument Security Procedures
This section describes the Meter’s memory elements and the procedures for clearing
them.

Volatile Memory
Table 1-1 lists the Meter’s volatile memory elements.

Table 1-1. Volatile Memory Space

Type Size Function

SDRAM 128 MB Out-guard measurement data, user strings, temporary configuration information,
and Ethernet Host name.

SRAM 4 MB In-guard Measurement data and configuration information.

To clear both volatile memory elements listed in Table 1-1:

1. Press M.
2. Press the MANAGE MEMORY soft key.
3. Press the ERASE MEMORY soft key.

Non Volatile Memory

Table 1-2 lists the Meter’s non-volatile memory elements.

Table 1-2. Non-volatile Memory Space

Type Size Function

Flash 128 MB Application program storage, user string, user data, user remote interface
settings, calibration constants.

Flash 4 MB FPGA hardware setup, application program storage, calibration constants.

To clear the 128 MB of non-volatile flash memory listed in Table 1-2:

1. Press M.
2. Press the MANAGE MEMORY soft key.
3. Press the ERASE USB/TEK soft key.
This process clears only the user accessible portion of memory.

Note
The 4 MB non-volatile memory element is not usable and cannot be
cleared by the user.

1-13
DMM4040/4050
Users Manual

Media Memory
The Meter has a front-panel USB port for connecting flash memory modules up to
2 Gigabytes capacity to store Meter configuration and measurement data. To clear a
memory module:
1. Press M.
2. Press the MANAGE MEMORY soft key.
3. Press the ERASE USB MEMORY soft key.

Accessories
Table 1-3 lists the available accessories for the 4040 and 4050.

Table 1-3. Accessories

Model / Part Description

Number

TL710 Premium Test Lead Set

196-3520-00

TP750 100 Ohm RTD Temperature Probe (DMM4050 only)

013-0369-00 Calibration fixture; 4 terminal shorting bar

Y8846S Rackmount Kit Single

Y8846D Rackmount Kit Dual

TL705 2X4 Wire Ohm Precision Test Leads

TL725 2X4 Wire Ohm Tweezers Test Leads

159-0487-00 F1, Fuse, 11 A, 1000 V, Fast, .406INX1.5IN, Bulk

159-0488-00 F2, Fuse, 440 mA, 1000 V, Fast, .406X1.375, Bulk

174-5813-00 USB to RS-232 cable assembly

012-0991-01 GPIB cable; Low EMI; 1 meter

159-0187-00 Fuse, 0.25 A, 250 V AC, slow blow

159-0063-00 Fuse, 0.125 A, 250 V, slow blow

HCTEK4321 Hard case, plastic

AC4000 Soft case, nylon

1-14
 Introduction and Specifications
General Specifications 1
General Specifications
Power
Voltage
100 V Setting ...................................................... 90 V to 110 V
120 V Setting ...................................................... 108 V to 132 V
220 V Setting ...................................................... 198 V to 242 V
240 V Setting ...................................................... 216 V to 264 V
Frequency ............................................................... 47 Hz to 440 Hz. Automatically sensed at power-on.
Power Consumption................................................ 28 VA peak (12 Watt average)

Dimensions
Height...................................................................... 88 mm (3.46 in.)
Width....................................................................... 217 mm (8.56 in.)
Depth ...................................................................... 297 mm (11.7 in.)
Weight..................................................................... 3.6 kg (8.0 lb)
Shipping Weight...................................................... 5.0 kg (11.0 lb)

Display
Vacuum Fluorescent Display, dot matrix

Environment
Temperature
Operating ............................................................ 0 °C to 55 °C
Storage ............................................................... -40 °C to 70 °C
Warm Up............................................................. 1 hour to full uncertainty specifications
Relative Humidity (non-condensing)
Operating ............................................................ 0 °C to 28 °C <90 %
28 °C to 40 °C <80 %
40 °C to 55 °C <50 %
Storage ............................................................... -40 °C to 70 °C <95 %
Altitude
Operating ............................................................ 2,000 Meters
Storage ............................................................... 12,000 Meters
Vibration and Shock................................................ Complies with MIL-PRF-28800F Class 3.

Triggering
Samples per Trigger ........................................... 1 to 50,000
Trigger Delay ...................................................... 0 s to 3600 s; in 10 μS increments
External Trigger Delay ........................................ <1 mS
External Trigger Jitter ......................................... <500 μS
Trigger Input ....................................................... TTL Levels
Trigger Output..................................................... 5 V maximum (open collector)

Memory
10,000 measurements, internal, and up to 2 Gigabyte capacity with USB memory module (available separately, see
“Accessories”) through front-panel USB port

Math Functions
Zero, dBm, dB, MX+B, Offset, DCV ratio and TrendPlot, Histogram, Statistics (min/max/average/standard deviation), and
Limit Test

Electrical
Input Protection....................................................... 1000 V all ranges

1-15
DMM4040/4050
Users Manual

Overrange ............................................................... 20 % on all ranges except 1000 V dc, 1000 V ac

Diode, and 10 A ranges

Remote Interfaces
RS-232C, DTE 9-pin, 1200 to 230400 baud (RS-232C to USB cable available to connect the Meter to a PC USB port.
See Accessories)
IEEE 488.2
LAN and “Ethernet 10/100 base T with DHCP (for IP_ADDRess) option”

Warranty
Three years

Electrical Specifications
Accuracy specifications are valid for 6½ digit resolution mode after at least a 1-hour warm-up with Auto Zero enabled.
24-hour specifications are relative to calibration standards and assume a controlled electromagnetic environment per
EN 61326-1:2000-11

DC Voltage Specifications
Maximum Input ....................................................... 1000 V on any range
Common Mode Rejection ....................................... 140 dB at 50 or 60 Hz ±0.1 % (1 kΩ unbalance)
Normal Mode Rejection .......................................... 60 dB for NPLC of 1 or greater with analog filter off and power line
frequency ±0.1 %
100 dB for NPLC of 1 or greater with analog filter on and power line
frequency ±0.1 %
Measurement Method ............................................. Multi-ramp A/D
A/D Linearity ........................................................... 0.0002 % of measurement +0.0001 % of range
Input Bias Current ................................................... <30 pA at 25 °C
Autozero Off Operation ........................................... Following instrument warm-up at calibration temperature ±1 °C and
less than 10 minutes, add error: 0.0002 % range additional error
+5 μV.
Analog Filter............................................................ When using the analog filter, specifications are relative to within one
hour of using the ZERO function for that range and NPLC setting.
DC Ratio ................................................................. Accuracy is +/- (Input accuracy + Reference accuracy), where Input
accuracy = DC Voltage accuracy for the HI to LO Input (in ppm of the
Input voltage), and Reference accuracy = DC Voltage accuracy for the
HI to LO (Sense) Reference (in ppm of the Reference voltage).
Settling Considerations ........................................... Measurement settling times are affected by source impedance, cable
dielectric characteristics, and input signal changes.

Input Characteristics
Resolution
Range Resolution Input Impedance
4½ Digits 5½ Digits 6½ Digits
[1]
100 mV 100.0000 mV 10 μV 1 μV 100 nV 10 MΩ or >10 GΩ
[1]
1V 1.000000 V 100 μV 10 μV 1 μV 10 MΩ or >10 GΩ
[1]
10 V 10.00000 V 1 mV 100 μV 10 μV 10 MΩ or >10 GΩ
100 V 100.0000 V 10 mV 1 mV 100 μV 10 MΩ ±1%
1000 V 1,000.000 V 100 mV 10 mV 1 mV 10 MΩ ±1%
[1] Inputs beyond ±14 V are clamped through 200 kΩ typical. 10 MΩ is default input impedance.

1-16
 Introduction and Specifications
Electrical Specifications 1
4050 Accuracy
Accuracy is given as ± (% measurement + % of range)
Temperature
24 Hour 90 Days 1 Year
Range Coefficient/ °C
(23 ±1 °C) (23 ±5 °C) (23 ±5 °C)
Outside 18 to 28 °C
100 mV 0.0025 + 0.003 0.0025 + 0.0035 0.0037 + 0.0035 0.0005 + 0.0005
1V 0.0018 + 0.0006 0.0018 + 0.0007 0.0025 + 0.0007 0.0005 + 0.0001
10 V 0.0013 + 0.0004 0.0018 + 0.0005 0.0024 + 0.0005 0.0005 + 0.0001
100 V 0.0018 + 0.0006 0.0027 + 0.0006 0.0038 + 0.0006 0.0005 + 0.0001
1000 V 0.0018 + 0.0006 0.0031 + 0.001 0.0041 + 0.001 0.0005 + 0.0001

4040 Accuracy
Accuracy is given as ± (% measurement + % of range)
Temperature
24 Hour 90 Days 1 Year
Range Coefficient/ °C
(23 ±1 °C) (23 ±5 °C) (23 ±5 °C)
Outside 18 to 28 °C
100 mV 0.003 + 0.003 0.004 + 0.0035 0.005 + 0.0035 0.0005 + 0.0005
1V 0.002 + 0.0006 0.003 + 0.0007 0.004 + 0.0007 0.0005 + 0.0001
10 V 0.0015 + 0.0004 0.002 + 0.0005 0.0035 + 0.0005 0.0005 + 0.0001
100 V 0.002 + 0.0006 0.0035 + 0.0006 0.0045 + 0.0006 0.0005 + 0.0001
1000 V 0.002 + 0.0006 0.0035 + 0.0010 0.0045 + 0.0010 0.0005 + 0.0001

Additional Errors
Digits NPLC Additional NPLC Noise Error
6½ 100 0 % of range
6½ 10 0 % of range
5½ 1 0.001 % of range
5½ .2 0.0025 % of range +12 μV
4½ 0.02 0.017 % of range +17 μV

AC Voltage Specifications
AC Voltage specifications are for ac sinewave signals >5 % of range. For inputs from 1 % to 5 % of range and <50 kHz,
add an additional error of 0.1 % of range, and for 50 kHz to 100 kHz, add 0.13 % of range.
7
Maximum Input ....................................................... 1000 V rms or 1414 V peak or 8 x 10 volts-Hertz product (whichever is
less) for any range.
Measurement Method ............................................. AC-coupled true-rms. Measures the ac component of input with up to
1000 V dc bias on any range.
AC Filter Bandwidth:
Slow .................................................................... 3 Hz – 300 kHz
Medium ............................................................... 20 Hz – 300 kHz
Fast ..................................................................... 200 Hz – 300 kHz
Common Mode Rejection ....................................... 70 dB at 50 Hz or 60 Hz ±0.1 % (1 kΩ unbalance)
Crest Factor Error (applies to non-sinusoidal waveforms only)
Maximum Crest Factor ....................................... 5:1 at Full Scale
Additional Crest Factor Errors (<100 Hz)............ Crest factor 1-2, 0.05 % of full scale
Crest factor 2-3, 0.2 % of full scale
Crest factor 3-4, 0.4 % of full scale
Crest factor 4-5, 0.5 % of full scale

1-17
DMM4040/4050
Users Manual

Input Characteristics
Resolution
Range Resolution Input Impedance
4½ Digits 5½ Digits 6½ Digits
100 mV 100.0000 mV 10 μV 1 μV 100 nV
1V 1.000000 V 100 μV 10 μV 1 μV
1 MΩ ±2 % shunted
10 V 10.00000 V 1 mV 100 μV 10 μV by <100 pf
100 V 100.0000 V 10 mV 1 mV 100 μV
1000 V 1,000.000 V 100 mV 10 mV 1 mV

4040/4050 Accuracy
Accuracy is given as ± (% measurement + % of range)
Temperature
24 Hour 90 Days 1 Year
Range Frequency Coefficient/ °C
(23 ±1 °C) (23 ±5 °C) (23 ±5 °C)
Outside 18 to 28 °C
100 mV 3 – 5 Hz 1.0 + 0.03 1.0 + 0.04 1.0 + 0.04 0.1 + 0.004
5 – 10 Hz 0.35 + 0.03 0.35 + 0.04 0.35 + 0.04 0.035 + 0.004
10 Hz – 20 kHz 0.04 + 0.03 0.05 + 0.04 0.06 + 0.04 0.005 + 0.004
20 – 50 kHz 0.1 + 0.05 0.11 + 0.05 0.12 + 0.05 0.011 + 0.005
50 – 100 kHz 0.55 + 0.08 0.6 + 0.08 0.6 + 0.08 0.06 + 0.008
[1]
100 – 300 kHz 4.0 + 0.50 4.0 + 0.50 4.0 + 0.50 0.20 + 0.02
1V 3 – 5 Hz 1.0 + 0.02 1.0 + 0.03 1.0 + 0.03 0.1 + 0.003
5 – 10 Hz 0.35 + 0.02 0.35 + 0.03 0.35 + 0.03 0.035 + 0.003
10 Hz – 20 kHz 0.04 + 0.02 0.05 + 0.03 0.06 + 0.03 0.005 + 0.003
20 – 50 kHz 0.1 + 0.04 0.11 + 0.05 0.12 + 0.05 0.011 + 0.005
50 – 100 kHz 0.55 + 0.08 0.6 + 0.08 0.6 + 0.08 0.06 + 0.008
[1]
100 – 300 kHz 4.0 + 0.50 4.0 + 0.50 4.0 + 0.50 0.2 + 0.02
10 V 3 – 5 Hz 1.0 + 0.02 1.0 + 0.03 1.0 + 0.03 0.1 + 0.003
5 – 10 Hz 0.35 + 0.02 0.35 + 0.03 0.35 + 0.03 0.035 + 0.003
10 Hz – 20 kHz 0.04 + 0.02 0.05 + 0.03 0.06 + 0.03 0.005 + 0.003
20 – 50 kHz 0.1 + 0.04 0.11 + 0.05 0.12 + 0.05 0.011 + 0.005
50 – 100 kHz 0.55 + 0.08 0.6 + 0.08 0.6 + 0.08 0.06 + 0.008
[1]
100 – 300 kHz 4.0 + 0.50 4.0 + 0.50 4.0 + 0.50 0.2 + 0.02
100 V 3 – 5 Hz 1.0 + 0.02 1.0 + 0.03 1.0 + 0.03 0.1 + 0.003
5 – 10 Hz 0.35 + 0.02 0.35 + 0.03 0.35 + 0.03 0.035 + 0.003
10 Hz – 20 kHz 0.04 + 0.02 0.05 + 0.03 0.06 + 0.03 0.005 + 0.003
20 – 50 kHz 0.1 + 0.04 0.11 + 0.05 0.12 + 0.05 0.011 + 0.005
50 – 100 kHz 0.55 + 0.08 0.6 + 0.08 0.6 + 0.08 0.06 + 0.008
[1]
100 –- 300 kHz 4.0 + 0.50 4.0 + 0.50 4.0 + 0.50 0.2 + 0.02
1000 V 3 – 5 Hz 1.0 + 0.015 1.0 + 0.0225 1.0 + 0.0225 0.1 + 0.00225
5 – 10 Hz 0.35 + 0.015 0.35 + 0.0225 0.35 + 0.0225 0.035 + 0.00225
10 Hz – 20 kHz 0.04 + 0.015 0.05 + 0.0225 0.06 + 0.0225 0.005 + 0.00225
20 – 50 kHz 0.1 + 0.03 0.11 + 0.0375 0.12 + 0.0375 0.011 + 0.00375
[2]
50 – 100 kHz 0.55 + 0.06 0.6 + 0.06 0.6 + 0.06 0.06 + 0.006
[1][2]
100 – 300 kHz 4.0 + 0.375 4.0 + 0.375 4.0 + 0.375 0.2 + 0.015
[1] Typically 30 % reading error at 1 MHz
[2] 1000 Volt range is limited to 8 X 107 volt-Hertz

1-18
 Introduction and Specifications
Electrical Specifications 1
Additional Low Frequency Errors
Error is stated as % of reading.
AC Filter
Frequency
3 HZ (slow) 20 HZ (medium) 200 HZ (fast)
10 – 20 Hz 0 0.25 –
20 – 40 Hz 0 0.02 –
40 – 100 Hz 0 0.01 0.55
100 – 200 Hz 0 0 0.2
200 Hz – 1 kHz 0 0 0.02
>1 kHz 0 0 0

Resistance
Specifications are for 4-wire resistance function, 2 x 4-wire resistance, or 2-wire resistance with zero. If zero is not used,
add 0.2 Ω for 2-wire resistance plus lead resistance, and add 20 mΩ for 2 x 4-wire resistance function.
Measurement Method ............................................. Current source referenced to LO input
Max. Lead Resistance (4-wire ohms) ..................... 10 % of range per lead for 10 Ω, 100 Ω, 1 kΩ ranges. 1 kΩ per lead on
all other ranges
Input Protection....................................................... 1000 V on all ranges
Common Mode Rejection ............................................140 dB at 50 or 60 Hz ±0.1 % (1 kΩ unbalance)
Normal Mode Rejection .......................................... 60 dB for NPLC of 1 or greater with analog filter off and power line
frequency ±0.1 %
100 dB for NPLC of 1 or greater with analog filter on and power line
frequency ±0.1 %
Analog Filter............................................................ When using the analog filter, specifications are relative to within one
hour of using the ZERO function for that range and NPLC setting.

Input Characteristics
Resolution
Range Resolution Source Current
4½ Digits 5½ Digits 6½ Digits
10 Ω 10.00000 Ω 1 mΩ 100 μΩ 10 μΩ 5 mA/13 V
100 Ω 100.0000 Ω 10 mΩ 1 mΩ 100 μΩ 1 mA/6 V
1 kΩ 1.000000 kΩ 100 mΩ 10 mΩ 1 mΩ 1 mA/6 V
10 kΩ 10.00000 kΩ 1Ω 100 mΩ 10 mΩ 100 μA/6 V
100 kΩ 100.0000 kΩ 10 Ω 1Ω 100 mΩ 100 μA/13 V
1 MΩ 1.000000 MΩ 100 Ω 10 Ω 1Ω 10 μA/13 V
10 MΩ 10.00000 MΩ 1 kΩ 100 Ω 10 Ω 1 μA/13 V
100 MΩ 100.0000 MΩ 10 kΩ 1 kΩ 100 Ω 1 μA || 10 MΩ/10 V
1.0 GΩ 1.000000 GΩ 100 kΩ 10 kΩ 1 kΩ 1 μA || 10 MΩ/10 V

1-19
DMM4040/4050
Users Manual

4040/4050 Accuracy
Accuracy is given as ± (% measurement + % of range)
Temperature
24 Hour 90 Days 1 Year
Range Coefficient/ °C
(23 ±1 °C) (23 ±5 °C) (23 ±5 °C)
Outside 18 to 28 °C
10 Ω 0.003 + 0.01 0.008 + 0.03 0.01+ 0.03 0.0006 + 0.0005
100 Ω 0.003 + 0.003 0.008 + 0.004 0.01 + 0.004 0.0006 + 0.0005
1 kΩ 0.002 + 0.0005 0.008 + 0.001 0.01 + 0.001 0.0006 + 0.0001
10 kΩ 0.002 + 0.0005 0.008 + 0.001 0.01 + 0.001 0.0006 + 0.0001
100 kΩ 0.002 + 0.0005 0.008 + 0.001 0.01 + 0.001 0.0006 + 0.0001
1 MΩ 0.002 + 0.001 0.008 + 0.001 0.01 + 0.001 0.001 + 0.0002
10 MΩ 0.015 + 0.001 0.02 + 0.001 0.04 + 0.001 0.003 + 0.0004
100 MΩ 0.3 + 0.01 0.8 + 0.01 0.8 + 0.01 0.15 + 0.0002
1 GΩ 1.0 + 0.01 1.5 + 0.01 2.0 + 0.01 0.6 + 0.0002

Additional Ohms Errors

Digits NPLC Additional NPLC Noise Error
6½ 100 0 % of range
6½ 10 0 % of range
5½ 1 0.001 % of range
5½ 0.2 0.003 % of range ±7 mΩ
4½ 0.02 0.017 % of range ±15 mΩ

DC Current
Input Protection....................................................... Tool-accessible 11 A/1000 V and 440 mA/1000 V fuses, limits of
400 mA continuous 550 mA for 2 minutes on, 1 minute off.
Common Mode Rejection ............................................140 dB at 50 or 60 Hz ±0.1 % (1 kΩ unbalance)
Normal Mode Rejection .......................................... 60 dB for NPLC of 1 or greater with analog filter off and power line
frequency ±0.1 %
100 dB for NPLC of 1 or greater with analog filter on and power line
frequency ±0.1 %
Analog Filter............................................................ When using the analog filter, specifications are relative to within one
hour of using the ZERO function for that range and NPLC setting.

Input Characteristics
Resolution Shunt Resistance
Range Resolution Burden Voltage
4½ Digits 5½ Digits 6½ Digits (Ohms)
100 μA 100.0000 μA 10 nA 1 nA 100 pA 100 Ω <0.015 V
1 mA 1.000000 mA 100 nA 10 nA 1 nA 100 Ω <0.15 V
10 mA 10.00000 mA 1 μA 100 nA 10 nA 1Ω <0.025 V
100 mA 100.0000 mA 10 μA 1 μA 100 nA 1Ω <0.25 V
[3]
400 mA 400.000 mA 100 μA 10 μA 1 μA 1Ω <0.50 V
[2]
1A 1.000000 A 100 μA 10 μA 1 μA 0.01 Ω <0.05 V
[1]
3A 3.00000A 1 mA 100 μA 10 μA 0.01 Ω <0.15 V
10 A 10.00000 A 1 mA 100 μA 10 μA 0.01 Ω <0.5 V
[1] Part of 10 A range.
[2] Available on the front panel terminal only.
[3] 400 mA continuously; 550 mA for 2 minutes on, 1 minute off.

1-20
 Introduction and Specifications
Electrical Specifications 1
Accuracy (4040/4050)
Accuracy is given as ± (% measurement + % of range)
Temperature
24 Hour 90 Days 1 Year
Range Coefficient/ °C
(23 ±1 °C) (23 ±5 °C) (23 ±5 °C)
Outside 18 to 28 °C
[4]
100 μA 0.01 + 0.02 0.04 + 0.025 0.05 + 0.025 0.002 + 0.003
1 mA 0.007 + 0.005 0.030 + 0.005 0.05 + 0.005 0.002 + 0.0005
[4]
10 mA 0.007 + 0.02 0.03 + 0.02 0.05 + 0.02 0.002 + 0.002
100 mA 0.01 + 0.004 0.03 + 0.005 0.05 + 0.005 0.002 + 0.0005
[3]
400 mA 0.03 + 0.004 0.04 + 0.005 0.05 + 0.005 0.005 + 0.0005
[2]
1A 0.03 + 0.02 0.04 + 0.02 0.05 + 0.02 0.005 + 0.001
[1][2]
3A 0.05 + 0.02 0.08 + 0.02 0.1 + 0.02 0.005 + 0.002
[2]
10 A 0.1 + 0.008 0.12 + 0.008 0.15 + 0.008 0.005 + 0.0008
[1] Part of 10 A range
[2] Available at front panel connectors only
[3] 400 mA continuously; 550 mA for 2 minutes on, 1 minute off.
[4] In RF fields of 3 V/m and frequencies of 1.7 GHz to 1.9 GHz, add 0.06% of range. With conducted RF
voltages of 3 Vrms and frequencies of 20 MHz to 50 MHz, add 0.08% of range.

Additional Current Errors

Additional NPLC Noise Error for Additional NPLC Noise Error
Digits NPLC 1 mA, 100 mA, 400 mA, 3 A and for 100 μA, 10 mA, 1 A
10 A
6½ 100 0 % of range 0 % of range
6½ 10 0 % of range 0 % of range
5½ 1 0.001 % of range 0.01 % of range
5½ 0.2 0.011 % of range ±4 μA 0.11 % of range ±4 μA
4½ 0.02 0.04 % of range ±4 μA 0.28 % of range ±4 μA

1-21
DMM4040/4050
Users Manual

AC Current
The following ac current specifications are for sinusoidal signals with amplitudes greater than 5 % of range. For inputs
from 1 % to 5 % of range, add an additional error of 0.1 % of range.
Input Protection....................................................... Tool accessible 11 A/1000 V and 440 mA/1000 V fuses, limits of
400 mA continuous 550 mA for 2 minutes on, 1 minute off.
Measurement Method ............................................. ac-coupled true-rms, dc-coupled to the fuse and shunt (no blocking
capacitor)
AC Filter Bandwidth
Slow .................................................................... 3 Hz to 10 kHz
Medium ............................................................... 20 Hz to 10 kHz
Fast ..................................................................... 200 Hz to 10 kHz
Crest Factor Error (applies to non-sinusoidal waveforms only)
Maximum Crest Factor ....................................... 5:1 at full scale
Additional Crest Factor Errors (<100 Hz)............ Crest factor 1-2, 0.05 % of full scale
Crest factor 2-3, 0.2 % of full scale
Crest factor 3-4, 0.4 % of full scale
Crest factor 4-5, 0.5 % of full scale

Input Characteristics
Resolution Shunt Resistance
Range Resolution Burden Voltage
4½ Digits 5½ Digits 6½ Digits (Ohms)
100 μA 100.0000 μA 10 nA 1 nA 100 pA 100 Ω <0.015 V
1 mA 1.000000 mA 100 nA 10 nA 1 nA 100 Ω <0.15 V
10 mA 10.00000 mA 1 μA 100 nA 10 nA 1Ω <0.025 V
100 mA 100.0000 mA 10 μA 1 μA 100 nA 1Ω <0.25 V
[3]
400 mA 400.000 mA 100 μA 10 μA 1 μA 1Ω <0.50 V
[2]
1A 1.000000 A 100 μA 10 μA 1 μA 0.01 Ω <0.05 V
[1][2]
3A 3.00000 A 1 mA 100 μA 10 μA 0.01 Ω <0.05 V
[2]
10 A 10.00000 A 1 mA 100 μA 10 μA 0.01 Ω <0.5 V
[1] Part of 10 A range
[2] Available at front panel connectors only
[3] 400 mA continuously; 550 mA for 2 minutes on, 1 minute off; maximum crest factor 3:1 at 400 mA

1-22
 Introduction and Specifications
Electrical Specifications 1
4040/4050 Accuracy
Accuracy is given as ± (% measurement + % of range)
Temperature
Frequency 24 Hour 90 Days 1 Year
Range Coefficient/ °C
(Hz) (23 ±1 °C) (23 ±5 °C) (23 ±5 °C)
Outside 18 to 28 °C
100 μA 3 – 5 Hz 1.1 + 0.06 1.1 + 0.06 1.1 + 0.06 0.2 + 0.006
5 – 10 Hz 0.35 + 0.06 0.35 + 0.06 0.35 + 0.06 0.1 + 0.006
10 Hz – 5 kHz 0.15 + 0.06 0.15 + 0.06 0.15 + 0.06 0.015 + 0.006
5 – 10 kHz 0.35 + 0.7 0.35 + 0.7 0.35 + 0.7 0.03 + 0.006
1 mA 3 – 5 Hz 1.0 + 0.04 1.0 + 0.04 1.0 + 0.04 0.1 + 0.006
5 – 10 Hz 0.3 + 0.04 0.3 + 0.04 0.3 + 0.04 0.035 + 0.006
10 Hz – 5 kHz 0.1 + 0.04 0.1 + 0.04 0.1 + 0.04 0.015 + 0.006
5 – 10 kHz 0.2 + 0.25 0.2 + 0.25 0.2 + 0.25 0.03 + 0.006
10 mA 3 – 5 Hz 1.1 + 0.06 1.1 + 0.06 1.1 + 0.06 0.2 + 0.006
5 – 10 Hz 0.35 + 0.06 0.35 + 0.06 0.35 + 0.06 0.1 + 0.006
10 Hz – 5 kHz 0.15 + 0.06 0.15 + 0.06 0.15+ 0.06 0.015 + 0.006
5 – 10 kHz 0.35 + 0.7 0.35 + 0.7 0.35 + 0.7 0.03 + 0.006
100 mA 3 – 5 Hz 1.0 + 0.04 1.0 + 0.04 1.0 + 0.04 0.1 + 0.006
5 – 10 Hz 0.3 + 0.04 0.3 + 0.04 0.3 + 0.04 0.035 + 0.006
10 Hz – 5 kHz 0.1 + 0.04 0.1 + 0.04 0.1 + 0.04 0.015 + 0.006
5 – 10 kHz 0.2 + 0.25 0.2 + 0.25 0.2 + 0.25 0.03 + 0.006
[3]
400 mA 3 – 5 Hz 1.0 + 0.1 1.0 + 0.1 1.0 + 0.1 0.1 + 0.006
5 – 10 Hz 0.3 + 0.1 0.3 + 0.1 0.3 + 0.1 0.035 + 0.006
10 Hz – 1 kHz 0.1 + 0.1 0.1 + 0.1 0.1 + 0.1 0.015 + 0.006
1kHz – 10 kHz 0.2 + 0.7 0.2 + 0.7 0.2 + 0.7 0.03 + 0.006
[2]
1A 3 – 5 Hz 1.0 + 0.04 1.0 + 0.04 1.0 + 0.04 0.1 + 0.006
5 – 10 Hz 0.3 + 0.04 0.3 + 0.04 0.3 + 0.04 0.035 + 0.006
10 Hz – 5 kHz 0.1 + 0.04 0.1 + 0.04 0.1 + 0.04 0.015 + 0.006
5 – 10 kHz 0.35 + 0.7 0.35 + 0.7 0.35 + 0.7 0.03 + 0.006
[1][2]
3A 3 – 5 Hz 1.1 + 0.06 1.1 + 0.06 1.1 + 0.06 0.1 + 0.006
5 – 10 Hz 0.35 + 0.06 0.35 + 0.06 0.35 + 0.06 0.035 + 0.006
10 Hz – 5 kHz 0.15 + 0.06 0.15 + 0.06 0.15 + 0.06 0.015 + 0.006
5 – 10 kHz 0.35 + 0.7 0.35 + 0.7 0.35 + 0.7 0.03 + 0.006
[2]
10 A 3 – 5 Hz 1.1 + 0.06 1.1 + 0.06 1.1 + 0.06 0.1 + 0.006
5 – 10 Hz 0.35 + 0.06 0.35 + 0.06 0.35 + 0.06 0.035 + 0.006
10 Hz – 5 kHz 0.15 + 0.06 0.15 + 0.06 0.15 + 0.06 0.015 + 0.006
5 – 10 kHz 0.35 + 0.7 0.35 + 0.7 0.35 + 0.7 0.03 + 0.006
[1] Part of 10 A range
[2] Available only on front panel connectors
[3] 400 mA continuously; 550 mA for 2 minutes on, 1 minute off; maximum crest factor 3:1 at 400 mA; specification for
current above 329 mA is typical.

1-23
DMM4040/4050
Users Manual

Additional Low Frequency Errors

Error is stated as % of reading.
AC Filter
Frequency
3HZ (slow) 20HZ (medium) 200HZ (fast)
10 – 20 Hz 0 0.25 –
20 – 40 Hz 0 0.02 –
40 – 100 Hz 0 0.01 0.55
100 – 200 Hz 0 0 0.2
200 Hz – 1 kHz 0 0 0.02
> 1 kHz 0 0 0

Frequency
Gate Times ............................................................. Programmable to 1 s, 100 ms, and 10 ms
Measurement Method ............................................. Flexible counting technique. AC-coupled input using the ac voltage
measurement function.
Settling Considerations ........................................... When measuring frequency or period after a dc offset voltage change,
errors may occur. For the most accurate measurement, wait up to
1 second for the input blocking capacitor to settle.
Measurement Considerations ................................. To minimize measurement errors, shield inputs from external noise
when measuring low-voltage, low-frequency signals.

4040/4050 Accuracy
Accuracy is given as ± % measurement
Temperature
24 Hour 90 Days 1 Year
Range Frequency Coefficient/ °C
(23 ±1 °C) (23 ±5 °C) (23 ±5 °C)
Outside 18 to 28 °C
100 mV to 3 – 5 Hz 0.1 0.1 0.1 0.005
[1][2]
1000 V
5 – 10 Hz 0.05 0.05 0.05 0.005
10 – 40 Hz 0.03 0.03 0.03 0.001
40 Hz – 300 kHz 0.006 0.01 0.01 0.001
300 kHz – 1 MHz 0.006 0.01 0.01 0.001
[1] Input >100 mV. For 10 – 100 mV, multiply percent measurement error by 10.
[2] Limited to 8 X 107 volt-Hertz

Gate Time vs. Resolution

Gate Time Resolution
0.01 5½
0.1 6½
1.0 6½

Additional Low Frequency Errors

Error stated as percent of measurement for inputs >100 mV. For 10 – 100 mV, multiply percent by 10.
Resolution
Frequency
6½ 5½ 4½
3 – 5 Hz 0 0.12 0.12
5 – 10 Hz 0 0.17 0.17
10 – 40 Hz 0 0.2 0.2
40 – 100 Hz 0 0.06 0.21
100 – 300 Hz 0 0.03 0.21
300 Hz – 1 kHz 0 0.01 0.07
> 1 kHz 0 0 0.02

1-24
 Introduction and Specifications
Electrical Specifications 1
Capacitance (4050 Only)
Accuracy is stated as ±(% of measurement + % of range)
[1]
1 Year Accuracy Temperature Coefficient/ °C
Range Resolution
(23 ±5 °C) Outside 18 to 28 °C
1 nF 1 pF 2% ± 2.5 % 0.05 + 0.05
10 nF 10 pF 1% ± 0.5 % 0.05 + 0.01
100 nF 100 pF 1% ± 0.5 % 0.01 + 0.01
1 μF 1 nF 1% ± 0.5 % 0.01 + 0.01
10 μF 10 nF 1% ± 0.5 % 0.01 + 0.01
100 μF 100 nF 1% ± 0.5 % 0.01 + 0.01
1 mF 1 μF 1% ± 0.5 % 0.01 + 0.01
10 mF 10 μF 1% ± 0.5 % 0.01 + 0.01
100 mF 100 μF 4% ± 0.2 % 0.05 + 0.05
[1] Stated accuracy is attained when Zero function is used.

Temperature (4050 only)

Test Current ............................................................ 1 mA
Accuracy is stated as ± °C and is based on a Platinum RT100 (DIN IEC 751, 385 type) RTD with less than 10 ohms lead
resistance. The accuracy listed in the table below are valid only when using the 4-wire RTD measurement function.
Specifications do not include probe accuracy, which must be added.
Accuracy Temperature
Range Resolution 90 Days 1 Year Coefficient/ °C
(23 ±5 °C) (23 ±5 °C) Outside 18 to 28 °C

-200 °C 0.001 °C 0.06 0.09 0.0025

-100 °C 0.001 °C 0.05 0.08 0.002
0 °C 0.001 °C 0.04 0.06 0.002
100 °C 0.001 °C 0.05 0.08 0.002
300 °C 0.001 °C 0.1 0.12 0.002
600 °C 0.001 °C 0.18 0.22 0.002

Additional Errors
Digits NPLC Additional NPLC Noise Error
6½ 100 0 °C
6½ 10 0 °C
5½ 1 0.03 °C
5½ 0.2 0.12 °C
4½ 0.02 0.6 °C

Continuity
Continuity Threshold ............................................... Selectable between 1 Ω and 1000 Ω
Test Current ............................................................ 1 mA
Response Time....................................................... 300 samples/sec with audible tone
Accuracy is given as ± (% measurements + % of range)

Temperature
24 Hour 90 Days 1 Year
Range Coefficient/ °C
(23 ±1 °C) (23 ±5 °C) (23 ±5 °C)
Outside 18 to 28 °C
1000.0 Ω 0.002 + 0.01 0.008 + 0.02 0.01 + 0.02 0.001 + 0.002

1-25
DMM4040/4050
Users Manual

Diode Test
Test Current ............................................................ 100 μA or 1 mA
Response Time....................................................... 300 samples/sec with audible tone.
Accuracy is given as ± (% measurements + % of range)
Temperature
24 Hour 90 Days 1 Year
Range Coefficient/ °C
(23 ±1 °C) (23 ±5 °C) (23 ±5 °C)
Outside 18 to 28 °C
5.0000 V 0.002 + 0.002 0.008 + 0.002 0.01 + 0.002 0.001 + 0.002
10.0000 V 0.002 + 0.001 0.008 + 0.002 0.01 + 0.002 0.001 + 0.002

Measurement Rates (IEEE488[4])

[1]
Integration Time Measurements/Second
Function Digits Setting 60 Hz (50 Hz) 4040 4050
DC Volts, DC Current, and 6½ 100 NPLC 1.67 (2) s 0.6 (0.5) 0.6 (0.5)
Resistance 6½ 10 NPLC 167 (200) ms 6 (5) 6 (5)
5½ 1 NPLC 16.7 (20) ms 60 (50) 60 (50)
5½ 0.2 NPLC 3.3 ms 270 270
4½ 0.02 NPLC 500 us 995 995
[2]
AC Voltage and AC Current 6½ 3 Hz 0.47 0.47
6½ 20 Hz 1.64 1.64
[3]
6½ 200 Hz 4.5 4.5
Frequency and Period 6½ 1s 1 1
5½ 100 ms 9.8 9.8
4½ 10 ms 80 80
Capacitance 6½ NA 2
[1] Typical measurement rates with auto-zero off, delay = 0, display off, auto range off and math off.
[2] Maximum measurement rates for 0.01 % of ac step. When dc input varies, additional settling delay is required.
[3] For remote operation or external trigger using default settling delay
[4] Note that the measurements rates for RS232 can vary depending on the baud rate chosen. If the baud rate selected is
115,200, the maximum measurement rate is 711 measurement/s. The LAN bus has a maximum measurement rate of
963 measurement/s.

1-26
 Chapter 2
Preparing the Meter for Operation

Title Page

Introduction.......................................................................................................... 2-3
Unpacking and Inspecting the Meter ................................................................... 2-3
Storing and Shipping the Meter ........................................................................... 2-3
Power Considerations .......................................................................................... 2-3
Selecting the Line Voltage .............................................................................. 2-3
Replacing the Fuses......................................................................................... 2-4
Line-Power Fuse ......................................................................................... 2-4
Current-Input Fuses..................................................................................... 2-5
Connecting to Line Power ................................................................................... 2-6
Turning Power-On ............................................................................................... 2-7
Adjusting the Bail ................................................................................................ 2-7
Installing the Meter in an Equipment Rack ......................................................... 2-8
Cleaning the Meter............................................................................................... 2-8
Fluke 45 Emulation Mode ................................................................................... 2-8

2-1
DMM4040/4050
Users Manual

2-2
 Preparing the Meter for Operation
Introduction 2
Introduction
This chapter explains how to prepare the Meter for operation by selecting the proper line
voltage, connecting an appropriate line power cord, and turning on the Meter. Also
included is information on the proper storage and cleaning of the Meter.

Unpacking and Inspecting the Meter

Every care is taken in the choice of packing material to ensure that your equipment will
reach you in perfect condition. If the equipment has been subject to excessive handling in
transit, there may be visible external damage to the shipping carton. In the event of
damage, the shipping container and cushioning material should be kept for the carrier’s
inspection.
Carefully unpack the Meter from its shipping container and inspect the contents for
damaged or missing items. If the Meter appears damaged or something is missing,
contact both the carrier and Tektronix immediately. Save the container and the packing
material in case you have to return the Meter.

Storing and Shipping the Meter

The Meter should be stored under cover. The shipping container provides the most
suitable receptacle for storage, as it provides the necessary shock isolation for normal
handling operations.
Place the Meter inside a sealed bag. Place the bag into the cushioning material inside the
shipping container, and store in a location that complies with the storage environment
specification described in Chapter 1.
If the Meter is shipped, use the original shipping container if possible. It provides shock
isolation for normal handling operations. If the original shipping container is not
available, a box that is 17.5″ x 15.5″ x 8.0″, with cushioning material that fills the space
between the Meter and the sides of the box, should provide similar shock isolation.

Power Considerations
The Meter operates on power distribution standards found throughout the world, and
must be set up to operate on the line voltage that will power it. The Meter is packed ready
for use with a line voltage determined at the time of ordering. If the selected line voltage
does not match the power the Meter will be plugged into, then the Meter’s line voltage
setting must be changed and the line fuse possibly replaced.

Selecting the Line Voltage

The Meter will operate on any one of four different input line voltages. The set line
voltage is visible through the window in the line fuse holder, found on the Meter's rear
panel.
To change the line voltage:
1. Remove the power cord from the Meter.
2. Insert a small screwdriver blade in the narrow recess to the left of the fuse holder and
pry to the right until the holder pops out, as shown in Figure 2-1.
3. Remove the voltage selector block from the fuse holder.
4. Rotate the selector block until the preferred voltage rating faces outward.

2-3
DMM4040/4050
Users Manual

5. Replace the selector block back into the fuse holder.

Changing the line voltage setting may require a different line-power fuse for proper
operation. Check Table 2-1 for the appropriate fuse for the selected line voltage.
With the voltage set and appropriate fuse installed, replace the fuse holder back into the
Meter and reconnect the power cord.

Replacing the Fuses

The Meter employs fuses to protect both the line-power and current measurement inputs.

Line-Power Fuse
The Meter has a line-power fuse in series with the power supply. Table 2-1 indicates the
proper fuse for each of the four line voltage selections. This fuse is located on the rear-
panel.
To replace this fuse:
1. Unplug the power cord from the Meter.
2. Remove the fuse holder by inserting a small screwdriver blade in the narrow recess to
the left of the fuse holder and pry to the right until the holder pops out as shown in
Figure 2-1. The Meter is shipped with a replacement fuse of the same rating as the
fuse installed in the fuse block.
3. Remove the fuse and replace with one rated appropriately for the selected line-power
voltage. See Table 2-1.
4. Replace the selector block back into the fuse holder.

XW Warning
To avoid electric shock or fire, do not use makeshift fuses or
short-circuit the fuse holder. Use only the fuses recommended
in this manual.

2-4
 Preparing the Meter for Operation
Power Considerations 2
Table 2-1. Line Voltage to Fuse Rating

Line Voltage Selection Fuse Rating Tektronix Part No.

100 / 120 0.25 A, 250 V (slow blow) 159-0187-00

220 / 240 0.125 A, 250 V (slow blow) 159-0063-00

120

caw0201f.eps
Figure 2-1. Replacing the Line Fuse

Current-Input Fuses
The 400 mA and 10 A inputs are protected by user-replaceable fuses.
• The 400 mA input is protected by a fuse (F2) rated at 440 mA, 1000 V (fast blow),
10,000 A minimum breaking capacity.
• The 10 A input is protected by a fuse (F1) rated at 11 A, 1000 V (fast blow),
10,000 A minimum breaking capacity.
W Warning
For protection against fire or arc flash, replace a blown fuse
only with one from Tektronix.
To test for a blown Current Input Fuse:
1. With the Meter powered up, plug a test lead into the VΩGER connector.
2. Press N.
3. Insert the other end of the test lead into the 400 mA input connector.
If the fuse is good, the Meter will read less than 200 Ω. If the fuse is blown, the
Meter will read overload.
4. Remove the probe from the 400 mA connector and insert into the 10 A
connector.
If the fuse is good, the Meter will read less than 1 Ω. If the fuse is blown, the
Meter will read overload.
To replace the Current Input fuses,

2-5
DMM4040/4050
Users Manual

1. Turn the Meter off, unplug the power cord from the Meter, and remove all test
leads.
2. Turn the Meter on its back.
3. Unscrew the retaining screw on the fuse access door as depicted in Figure 2-2.
4. Remove the protective cover from the fuse holders by slightly depressing the
back edge of the cover to unlatch it from the printed circuit board. Pull up on the
back edge of the cover and remove it from the fuse compartment.
5. Remove the defective fuse, and replace with one having the appropriate rating.
6. Replace the protective cover by pushing it over the fuses while aligning the
catches with the holes in the printed circuit board. Press the cover down until the
catches engage the printed circuit board.
7. Replace the fuse door and secure it by tightening the retaining screw.

Fuses F1
F2
Bottom front
left corner

caw020.eps
Figure 2-2. Replacing the Current Input Fuses

Connecting to Line Power

XW Warning
To avoid shock hazard, connect the factory supplied three-
conductor line power cord to a properly grounded power outlet.
Do not use a two-conductor adapter or extension cord; this will
break the protective ground connection. If a two-conductor
power cord must be used, a protective grounding wire must be
connected between the ground terminal and earth ground
before connecting the power cord or operating the instrument.

2-6
 Preparing the Meter for Operation
Turning Power-On 2
1. Verify that the line voltage selector block is set to the correct setting.
2. Verify that the correct fuse for the line voltage is installed.
3. Connect the power cord to a properly grounded three-prong outlet. Refer to Table
2-2 for descriptions of the line-power cord types available from Tektronix.

Table 2-2. Line-Power Cord Types Available from Tektronix

Type Voltage/Current Tektronix Part Number

North America 120 V / 15 A 161-0066-00

North America 250 V / 10 A 161-0066-12

Universal Euro 250 V / 10 A 161-0066-09

United Kingdom 250 V / 10 A 161-0066-10

Switzerland 250 V / 10 A 161-0154-00

Australia 250 V / 10 A 161-0066-13

Japan 125V / 7A 161-0298-00

China 250V / 10A 161-0304-00

Turning Power-On
XW Warning
To avoid electric shock, connect the Meter’s power cord to a
power receptacle with proper earth ground. A protective ground
connection by way of the grounding conductor in the power
cord is essential for safe operation.
With the proper line voltage selected and the appropriate power cord connected to the
Meter, connect the power cord to a power outlet and switch rear-panel power switch so
the “I” side of the switch is depressed.

Adjusting the Bail

For bench-top use, the Meter’s bail or handle is adjustable to provide two viewing angles.
To adjust its position, pull the ends out to a hard stop (about 1/4-inch on each side) and
rotate it to one of the four stop positions shown in Figure 2-3. To completely remove the
handle, adjust it to the vertical stop position and pull the ends all the way out.

2-7
DMM4040/4050
Users Manual

1 Store 2 Tilt up

BACK F1 F2 F3 F4 F5 MEMORY

INSTR
DC V ACV DC I AC I TRIG
SETUP
RANGE
FREQ ZERO MEAS
PERIOD TEMP ANALYZE
SETUP

3 Carry

4 Remove

caw017.eps
Figure 2-3. Bail Adjustment and Removal

Installing the Meter in an Equipment Rack

The Meter is mountable in a standard 19-inch rack using a rack mount kit. See the
“Accessories” section in Chapter 1 for ordering information. In preparation for rack
mounting, remove the bail (see the “Adjusting the Bail” section above) and the front and
rear protective boots. Then refer to the instructions provided with the Rack Mount Kit to
mount the Meter.

Cleaning the Meter

XW Warning
To avoid electric shock or damage to the Meter, never get water
inside the meter.

W Caution
To avoid damaging the Meter’s housing, do not apply solvents
to the Meter.
If the Meter requires cleaning, wipe it down with a cloth lightly dampened with water or
a mild detergent. Do not use aromatic hydrocarbons, chlorinated solvents, or methanol-
based fluids when wiping down the meter.

Fluke 45 Emulation Mode

The Fluke 45 emulation mode enables you to use programs that run on the Fluke 45
multimeter model on the Tektronix DMM4040 and DMM4050. See Sample Program
Using the RS-232 Computer Interface in Chapter 3 to view a sample program.

2-8
 Preparing the Meter for Operation
Fluke 45 Emulation Mode 2
To switch the Meter to Fluke 45 emulation:
1. Press I.
2. Press 2 to select the COMMANDS menu. This will now show the current
command setup.
3. Press 2 to select Fluke 45. The active mode will appear bright in the
display, while the other is dim.

2-9
DMM4040/4050
Users Manual

2-10
 Chapter 3
Front-Panel Operation

Title Page

Introduction.......................................................................................................... 3-3
Controls and Indicators ........................................................................................ 3-4
Front-Panel Feature Descriptions .................................................................... 3-4
Display Panel................................................................................................... 3-5
Rear-Panel Connectors .................................................................................... 3-7
Adjusting the Meter’s Range........................................................................... 3-8
Navigating the Front-Panel Menu........................................................................ 3-8
Configuring the Meter for a Measurement .......................................................... 3-8
Setting the Beeper State................................................................................... 3-8
Setting the Display Resolution ........................................................................ 3-9
Setting the AC Signal Filter ............................................................................ 3-9
Setting Continuity Resistance Threshold and Diode Test Parameters ............ 3-10
Setting the Default Temperature Scale (4050 Only) ....................................... 3-10
Enabling High Input Impedance...................................................................... 3-10
Using the Analyze Functions ............................................................................... 3-11
Collecting Statistics on Measurements............................................................ 3-11
Testing Using Limits ....................................................................................... 3-12
Setting an Offset Value ................................................................................... 3-13
Using MX+B ................................................................................................... 3-13
Using TrendPlot............................................................................................... 3-14
Using the Histogram Function......................................................................... 3-16
Controlling Trigger Functions ............................................................................. 3-16
Choosing a Trigger Source .............................................................................. 3-17
Setting the Trigger Delay ................................................................................ 3-18
Setting the Number of Samples ....................................................................... 3-18
Understanding the Measurement Complete Signal ......................................... 3-18
Accessing and Controlling Memory................................................................ 3-18
Storing Readings in Memory........................................................................... 3-19
Recalling Readings from Memory .................................................................. 3-20
Storing Meter Configuration Information ....................................................... 3-21
Storing the Power-up Configuration................................................................ 3-22
Recalling the Power-up Configuration ............................................................ 3-22
Removing the Power-up Configuration........................................................... 3-22
Recalling a Meter Configuration ..................................................................... 3-23
Managing Memory .......................................................................................... 3-23
Controlling System-Related Operations .............................................................. 3-24
3-1
DMM4040/4050
Users Manual

Identifying Meter Errors.................................................................................. 3-24

Querying the Firmware for Revision Level..................................................... 3-24
Adjusting Display Brightness.......................................................................... 3-25
Setting the Meter’s Date and Time.................................................................. 3-25
USB Operation ................................................................................................ 3-25
USB Storage Capacity and Write Time........................................................... 3-25
USB Memory Device Compatibility and Special Instruction ......................... 3-26
Configuring the Remote Interface ....................................................................... 3-26
Sample Program Using the RS-232 Computer Interface ..................................... 3-26
Checking the Meter’s Calibration Date ............................................................... 3-28
Resetting the Meter’s Default Settings ................................................................ 3-28

3-2
 Front-Panel Operation
Introduction 3
Introduction
The Meter can be controlled either by sending commands through one of its
communication interfaces or by manually operating its front panel controls. This chapter
explains the function and use of the controls and indicators located on the front and rear
panels of the Meter. Operating the Meter through its computer interfaces is covered in the
Programmers Manual. The following features are not available in OutGuard SW versions
earlier than 2.0: DCI with DCV dual-function, DCV Ratio, 400 mA range, and digital
filter. Also, the function softkey positions for earlier releases are slightly different than
illustrated.
To view the OutG SW version:
1. Press I
2. Press the softkey labeled SYSTEM.
3. Press the softkey labeled VERSION.

3-3
DMM4040/4050
Users Manual

Controls and Indicators

Front-Panel Feature Descriptions
Table 3-1 shows the Meter’s front-panel controls and connectors.

Table 3-1. Front-Panel Controls and Connectors

1 2 3 4

INPUT SENSE TEKTRONIX DMM4050 6-1/2 DIGIT PRECISION MULTIMETER

V 4W
2W/4W

HI HI

1000 V CAT I 300V

600V CAT II

1V
FUSED

400 10A BACK F1 F2 F3 F4 F5 MEMORY

mA
INSTR
REAR FRONT DC V ACV DC I AC I TRIG
SETUP
RANGE
FREQ ZERO MEAS
PERIOD TEMP ANALYZE
SETUP

16 14 12
15 13 11 10 8 6

9 7 5
4040 Only
FREQ PERIOD

gdc04.eps

Item Description

Input HI and LO connectors. Input connectors for Volts, 2-wire Ohms, Hz, Period,
Temperature, and Capacitance measurements. Input connectors source current
for 4-wire Ohms measurements. All measurements use the Input LO connector as
A a common input. The LO input is isolated, and may be safely floated up to 1000 V
above earth ground regardless of the measurement type. 1000 V is the maximum
voltage rating between the Input HI and LO connectors and between each HI and
LO input and earth ground.

Sense HI and LO connectors. Sense connectors sense the voltage across the
B unknown resistance for 4-wire Ohms measurements or provide the DCV
reference Input for DCV Ratio measurements.

Soft keys F1 through F5. Soft keys are used to select various menu options while
C navigating the Meter’s menus. Each soft key’s function is identified with a label in
the bottom row of the display. Keys without a label above them are inactive

3-4
 Front-Panel Operation
Controls and Indicators 3
Table 3-1. Front-Panel Controls and Connectors (cont.)

Item Description

Memory key for accessing internal and external memory containing meter setups and
D measurements. See the “Accessing and Controlling Memory” section for more
information.

USB Port. Connection for USB memory device that can be used to store meter readings
E (memory device not included).

Standby key to turn off the display. While in standby, the Meter will not respond to
F remote or front-panel commands. When taken out of standby, the Meter sets itself to its
power-up configuration.

Instrument Setup key. Accesses communication interface selection and setup, remote
G command set, system settings, and meter reset.

Measurement Setup key. Accesses to resolution setting, trigger functions, temperature

H setup, dBm reference selection, continuity settings, and other measurement related
parameters.

Trigger key. Triggers measurement when trigger is set to external triggering. See the
I “Controlling Trigger Functions” section later in this chapter to learn how to use the
trigger key (TRIG) to control the Meter’s measurement cycle.

J Analyze key. Accesses math functions, Statistics, TrendPlot, and Histogram.

K Zero key. Uses the present reading as an offset value to create relative readings.

Meter function keys. Selects meter function between volts dc, volts ac, amp dc, amps
L ac, ohms, continuity, diode test, frequency, period, capacitance [1], and temperature [1].
For the 4040, the lower four keys select different functions; see inset.

Range keys. Selects between manual and auto range mode. Also increases or
M decreases the range when in manual ranging mode.

N Back key. Backs up one layer in the menu selection.

Front and Rear input switch. All front-panel input connectors, except 10 A, are available
O on the rear-panel of the Meter. These switches switch the Meter’s input between them.

P 400 mA and 10 A input connectors for ac and dc current measurement functions.

Notes:

[1] Available on 4050 only

Display Panel
The display panel described in Table 3-1, performs the following three functions:
• Displays measurements as a value, with measurement units, and measurement statistics
in both numerical and graphical format (TrendPlot and Histogram).
• Displays soft labels for soft keys, F1 through F5.
• Identifies the current mode of operation, Local (MAN) or Remote (REM).

3-5
DMM4040/4050
Users Manual

Table 3-2. Display Elements

1
mV V ...
12 2
11 3

10
100.0002 Hz 4

8
-0.4561
123.123. 123.123.
mV~ 6
5

ENTER
--
7
caw02f.eps

Item Description

A Primary display.

B Secondary display.

C Indicates PASS, HIGH or LOW for limits testing.

D Math function selected.

E Error detected.

F Memory enabled for storing readings. Extinguishes when last sample is stored.

G Softkey labels.

H Manual range mode selected. See “Adjusting the Meter’s Range” section.

I The Meter is under remote control.

J External Trigger Enabled.

K Rear inputs connectors selected.

L Menu selection path.

Measurement results occupy the first two rows of the display. The primary display
consists of larger sized characters that comprise the 6½ digits (-1999999 to 1999999),
plus a decimal point. In the example shown above, the primary display shows
measurement results for an ac voltage measurement.
The secondary display is smaller than the primary display and located in the upper right
area of the display. However, it is also capable of displaying 6½ digits. Its function is to
display the results of a secondary measurement associated with the primary measurement.
In the example shown, the secondary display shows the frequency of the ac voltage
measurement.
The Soft Key labels, row three, identify the functions of the five soft keys just below the
display.

3-6
 Front-Panel Operation
Controls and Indicators 3
Rear-Panel Connectors
Table 3-3 indicates the connections on the rear panel and describes their use.

Table 3-3. Rear-Panel Connectors

1 2 3
4

1/4 A SLOW FUSE,100/120 VAC 47 - 440 Hz INPUT SENSE

1/8 A SLOW FUSE, 220/240 VAC 25 VA MAX V 4W
CAUTION:
FOR FIRE PROTECTION REPLACE HI HI
ONLY WITH A 250V FUSE
AS STATED IN MANUAL.
1000 V CAT I
600V CAT II 300V
CAL STICKER
LO LO

1V
IEEE488 FUSED
LAN
RS-232
TRIG I/O 400 mA

LR44340

WARNING: N60
TO AVOID ELECTRIC SHOCK SERIAL TAG
GROUNDING CONNECTOR TEKTRONIX CORPORATION
IN POWER CORD NO INTERNAL USER SERVICEABLE PARTS Assembled in USA
MUST BE CONNECTED REFER SERVICE TO QUALIFIED SERVICE PERSONNEL www.tektronix.com

9 8 7 6 5

gdc05.eps

Item Description

A Line Power Cord connector

B Power Switch

C Fuse holder and power line voltage selector

D Rear-panel input connectors[1]

E External trigger input and measurement complete output port

F Ethernet (LAN) connector

G RS-232 connector. See appendix C for signals available on this connector.

H IEEE 488 (GPIB) connector

I Ground connector

Notes:

[1] 10 A current measurements can not be performed through the rear-panel connectors

3-7
DMM4040/4050
Users Manual

Adjusting the Meter’s Range

The range keys, (URV), switch the Meter between auto and manual ranging. The
presence or absence of MAN in the display indicates the Meter’s ranging mode. All
functions utilize these keys to control the Meter’s range except continuity, diode test,
temperature (4050 only), frequency and period, which only have a single range.

Note
The secondary display’s range is always the same as that of the primary
display when the functions are the same.
Pressing R causes the Meter to toggle between auto and manual ranging mode. The
autorange selected range in use when you enter the manual range mode becomes the
selected range. The Meter will extinguish MAN when autorange is selected.
Pressing U or V causes the Meter to switch from auto to manual ranging and moves
the range up or down respectively from the range autorange had selected. MAN will also
appear in the display. If the input signal is greater than the selected range can measure,
the Meter displays overload and sends 9.9000 E+37 over the remote interface.
In autorange mode, the Meter automatically selects the next highest range when the
measured value exceeds full scale of the present range. If no higher range is available,
overload is displayed on the primary or secondary display. The Meter automatically
selects the next lower range if the measured value drops below (11 %) of full scale.

Navigating the Front-Panel Menu

The Meter uses a multilevel menu system for the selection of function parameters,
configuration, and features. Menu selection and navigation is accomplished with the front
panel’s five function keys (12345) and B key. Labeling of the
five function keys is presented across the bottom row of the display and is dependent on
which function is selected.
The following sections, “Configuring the Meter for a Measurement” and Chapter four’s
instructions on “Making Measurements”, cover the use of the Meter’s menu system.

Configuring the Meter for a Measurement

The Meter’s display resolution, reading rate, trigger mode, continuity threshold, beeper
on/off, input impedance setting, default temperature scale, and dBm reference are
adjustable through the Measurement Setup function.

Setting the Beeper State

The Meter will emit a tone when a limit is exceeded during limit testing and when a
forward-biased diode is measured during diode testing. To disable the beeper for these
two conditions:
1. Press L.
2. Press the softkey labeled MORE.
If the softkey labeled BEEP ON is highlighted, press it to disable the beeper.

Note
Disabling the beeper has no effect on the tone when an error is generated
during remote operation or when the continuity threshold is exceeded
during continuity testing.

3-8
 Front-Panel Operation
Configuring the Meter for a Measurement 3
The beeper state is stored in non-volatile memory and does not change when the Meter is
turned off or after a remote interface reset. The beeper is enabled when the Meter is
shipped from the factory.

Setting the Display Resolution

The steps for setting the Meter’s displayed resolution, varies depending on the selected
function. The dc volts, dc current and ohms functions set the resolution based on the
power line cycle (PLC) setting. AC volts, ac current, capacitance and temperature set
resolution using a low, medium or high setting.
To set the Meter’s display resolution dc volts, dc current and ohms:
1. Press L to see the measurement Setup menu.
2. Press the soft key under the RESOLUTION #DIG PLC label to reveal the
resolution selection menu.
The soft key labels are updated with five choices.
4 DIGIT .02 PLC
5 DIGIT .2 PLC
5 DIGIT 1 PLC
6 DIGIT 10 PLC
6 DIGIT 100 PLC
These choices determine the displayed resolution (4½, 5½, and 6½ digits) and the
measurement cycle time in reference to the power line frequency in cycles (PLC)
For example, selecting 5 DIGIT 1 PLC will display 5½ digit resolution and take
a measurement using one power line cycle A/D integrate period. For 60 Hz power, a
measurement is almost once every 60th of a second or 16.6666 milliseconds.
3. Press the soft key labeled with the desired resolution.

Note
Some of the faster PLC choices are not available when 2nd MEAS or DCV
Ratio are selected.
To set the Meter’s display resolution for ac volts, ac current, capacitance and
temperature:
1. Press L to see the measurement Setup menu.
2. Press the soft key under the RESOLUTN label to reveal the resolution selection
menu.
Three soft key labels are updated with HIGH, MEDIUM, and LOW. The actual
number of digits displayed will depend on the selected function and the Meter’s
range.
3. Press the soft key labeled with the desired resolution.

Setting the AC Signal Filter

There are three ac filter settings that can be employed to help make more accurate
measurements: 3 Hz Slow, 20 Hz, and 200 Hz.
For the ac volts and ac current functions, a filter selection is available as a modifier.
Pressing the Filter soft key will expose a menu that allows you to select between the
three filter settings.

3-9
DMM4040/4050
Users Manual

Note
The 20 Hz filter is the power-up default selection.

Setting Continuity Resistance Threshold and Diode Test Parameters

The threshold resistance value for the continuity function and the amount of current and
voltage used for Diode testing are adjustable. Continuity resistance threshold can be set to
four different values: 1 Ω, 10 Ω, 100 Ω and 1 kΩ. Diode test voltage and current can also
be set to two different values: 5 V or 10 V and 1 mA or 0.1 mA.

Setting the Continuity Threshold Resistance

The resistance threshold can be set at 1, 10, 100, or 1000 Ω. To set the threshold:
1. Press Lto see the Measurement Setup menu.
2. Press the MORE soft key.
3. Press the CONTIN OHMS soft key.
4. Press the soft key labeled with the desired threshold.
Refer to the “Testing Continuity” section in Chapter 4 to test continuity.

Setting the Diode Test Voltage and Current

To set the diode test current:
1. Press S twice on the 4050, or press D once on the 4040, to select the Diode
function.
2. Press the 1€A or 0.1€A soft key to set the diode test current.
3. Press the 5V or 10V soft key to set the diode test voltage.
Refer to the “Checking Diodes” section in Chapter 4 to check diodes.

Setting the Default Temperature Scale (4050 Only)

When the temperature function is selected, the Meter displays temperature measurements
based on a preselected (default) temperature scale.
To change the default temperature scale:
1. Press Lto see the measurement setup selection menu.
2. Press the TEMP UNITS soft key to display the temperature scale selection menu.
Available temperature scales are C for Celsius (°C), F for Fahrenheit (°F) and K for
Kelvin (K).
3. Press the soft key labeled with the desired scale.
Refer to the “Measuring Temperature” section in Chapter 4 to make a temperature
measurement with the Meter.

Enabling High Input Impedance

The DCV input impedance of the Meter is normally set to 10 MΩ. Enabling the high
input impedance feature allows the input impedance to exceed 10 GΩ for the 10 V and
lower DCV ranges.
To enable high input impedance:
1. Press Lto see the Measurement Setup menu.

3-10
 Front-Panel Operation
Using the Analyze Functions 3
2. Press the MORE soft key.
3. Press the HIGH INPUT Z soft key.
The soft key label becomes highlighted to indicate high input Z is activated. Press the
soft key again to disable the function.

Using the Analyze Functions

The Meter is capable of performing mathematical operations with measured values, as
well as tracking a series of measurements. With the exception of Diode Test and
Continuity, all Meter functions work with all analysis functions. The mathematical
functions include statistics, limits, offset, and mX + b. Meter measurement tracking is
performed through the TrendPlot and Histogram functions.
To access the analyze functions press J.

Collecting Statistics on Measurements

The statistical analysis function displays the minimum and maximum measurements of a
series of Meter measurements. The Meter also calculates an average and a standard
deviation value for the same measurement series. This function also provides control over
the starting and stopping of the measurement series.

Starting the Measurement Collection

To start the statistics process:
1. Press J to display the Meter’s analysis menu.
2. Press the STATS soft key.
The Meter starts collecting data immediately. Individual readings are never stored in
the Meter, but each reading is added to the Average and Standard Deviation
calculation. At the same time, the measured value is compared to the values stored in
the minimum and maximum registers, and overwrites one of these values if it is
lower than the minimum value or greater than the maximum value.
While a series of measurements are being collected, the process can be stopped by
pressing the STOP soft key. To start calculations on another series of measurements,
press the RESTART soft key.

Reading the Min, Max, Std. Dev. and Avg. Values

As the measurements are collected, the display is continually updated with the latest
statistical data as shown below.

F1 F2 F3 F4 F5

caw03.eps

The minimum, maximum, average, and standard deviation is displayed along with the
number of measurements the statistics were calculated on.

3-11
DMM4040/4050
Users Manual

Stopping Measurement Collection

There are two methods of stopping the collection of measurements for the statistics
function.
To manually stop the measurement collection, press the STOP soft key from the
statistics menu. The display will update with the final set of statistical data.
The process can also be stopped automatically by entering the number of samples on
which you want to calculate statistics. To enter the number of statistic samples:
1. While in the statistics function, press #SAMPLES.
To select the digit to adjust, press the soft key labeled either <-- or -->.
With the desired digit selected, press the soft key labeled -- to decrement the digit
or ++ to increment the character.
2. Press ENTER to set the number of samples.

Note
Setting the number of samples to zero will cause the Meter to collect
samples continuously.

Testing Using Limits

The limits function provides Pass/Fail testing to user specified upper and lower limits.
The upper and lower limits are stored in volatile memory and will be set to zero when the
Meter is first turned on or the meter receives a reset through the remote interface.
Changing the function will also set the limits to zero.

+ 0.69897 V
HIGH LOW
F1 F2 F3 F4 F5
caw029.eps

When testing from the front panel, the Meter displaysOK in the secondary display when
the measurement is between the high and low limit. It displays HIGH or LOW, as shown
above, for each measurement that exceeds the upper or lower limit. The beeper will beep
once (if enabled) for the first measurement outside the limits after an OK measurement.
For remote operation, the Meter can be set to generate a service request (SRQ) on the
first occurrence of a measurement outside the limits. See the Programmers Manual for
information on enabling SRQ for this test.
To set the high and low limits through the front panel:
1. Press J.
2. Press the MATH soft key
3. Press the LIMITS soft key.
4. Press the HIGH or LOW soft key as shown above to set the high or low limit
respectively.
To select the digit to adjust, press either <-- or -->.

3-12
 Front-Panel Operation
Using the Analyze Functions 3
With the desired digit selected, press the soft key labeled -- to decrement the digit
or ++ to increment the character. The right most character is the multiplier. This
character can be set to p, n, μ, m, k, M, or G.
5. Press ENTER to set the selected limit.
6. Press ENABLE to start the limits testing.

Note
Since the high and low limits are independent of each other, both high and
low limit conditions could be satisfied by a measurement. In this case, the
Meter gives priority to the low limit condition by displaying LOW and
setting the low bit of the questionable data event register.
Refer to the Programmers Manual for instructions on setting the limits remotely.

Setting an Offset Value

The offset function provides a means of displaying the difference between a measured
value and a stored offset value. This type of measurement is referred to as a relative
measurement.
There are two methods of entering an offset value into the Meter. The first method is to
enter a specified number into the offset register either through the front-panel or over the
remote interface. Previously stored values are replaced with the new value. The offset
value is stored in volatile memory and is set to zero when power is applied to the Meter
or the Meter receives a reset through the remote interface.
The second method is to measure the desired reference value through the Meter’s input
connections and press Z. The measured value is placed into the offset register and the
display immediately starts showing the difference between measurements and the stored
value.

Note
The Zero key cannot be used to zero a DB or DBM measurement. Refer to
“Measuring AC Voltage” in Chapter 4 of this manual.
To enter an offset value through the front-panel:
1. Press J
2. Press the MATH soft key
3. Press the OFFSET soft key.
To select the digit to adjust, press either <-- or -->.
With the desired digit selected, press the soft key labeled -- to decrement the digit
or ++ to increment the character. The right most character is the multiplier. This
character can be set to p, n, μ, m, k, M, or G.
4. Press ENTER to set the value in the offset register.

Note
Limits and Offset are Math functions that cannot be active simultaneously.

Using MX+B
The MX+B function provides a means of calculating a linear value using a measured
value (X) and two constants: M and B. The constant M represents a gain, while the
constant B represents an offset.

3-13
DMM4040/4050
Users Manual

To make an mX+B calculation:

1. Press J.
2. Press the MATH soft key.
3. Press the €X+B soft key.
To enter the M value:
4. Press the €X soft key
To select the digit to adjust, press either <-- or -->.
With the desired digit selected, press the soft key labeled -- to decrement the digit
or ++ to increment the character.
5. Press ENTER to enter the M value.
6. Press Bto return to the MX+B menu.
To enter the B value:
7. Press the B soft key.
To select the digit to adjust, press either <-- or -->.
With the desired digit selected, press the soft key labeled -- to decrement the digit
or ++ to increment the character. The right most character is the multiplier. This
character can be set to p, n, μ, m, k, M, or G.
8. Press the ENTER soft key.
9. Press B to return to the MX+B menu.
10. Press the ENABLE soft key to start MX+B calculations.
ENABLE stays highlighted, and all displayed values are the measured value modified by
the formula MX+B.
Pressing ENABLE again disables MX+B, and ENABLE is no longer highlighted. The
MX+B calculation is applied after other MATH scaling calculations, but before other
MATH comparisons.

Using TrendPlot
TrendPlot provides a visual representation of the measured signal over time. About three-
quarters of the Meter’s display is used to plot the maximum and minimum readings
vertically, while the horizontal axis represents time. The vertical and horizontal axis’ are
not calibrated, and only represent relative time and amplitude depending on the input
signal.
Each plot mark is a one pixel-wide vertical line that represents the highest (top of mark)
and lowest (bottom of mark) reading the Meter has taken in the time since the previous
mark was made. The left-most plot mark represents the time TrendPlot was started. When
all available plot points across the plot area are filled, the Meter compresses the plot
marks to one-half of the plot area. The compression process takes the highest and lowest
reading between every two plot marks, and makes a single plot mark representing the
highest and lowest readings of the two combined plot marks. Future plot marks added to
the end of the compressed display are now the Meter’s highest and lowest readings, taken
over a time period twice as long as the period before the compression.
If the amplitude of the measured value exceeds the positive or negative range of the
vertical axis, the Meter adjusts the vertical range to accommodate the range of the new

3-14
 Front-Panel Operation
Using the Analyze Functions 3
plot point. Previously laid down plot marks are adjusted down in size proportionally to
the new vertical axis.
The left section of the Meter’s display indicates the highest (maximum) and lowest
(minimum) reading taken since the start of a TrendPlot session. In addition, the length of
the TrendPlot session is displayed in hours, minutes, and seconds (hh:mm:ss).
To start a TrendPlot session:
1. Set up the Meter for the desired measurement by selecting the function and
connecting the signal to the Meter’s input.

Note
Setting the range function to manual will cause the Trendplot display to
plot at the top or bottom edge of the plot area without making an amplitude
adjustment when the input signal exceeds the limits of the Meter’s range.
2. With the Meter taking measurements, press J.
3. Press the TREND PLOT soft key to start the session.
As shown in Figure 3-1, the display will start plotting the readings across the plot area,
and the maximum, minimum, and elapsed time are displayed. When there are longer
intervals or delays between readings, TrendPlot will initially look like unconnected dots
until enough time elapses to gather more readings.

STOP
F1 F2 F3 F4 F5

caw057.eps
Figure 3-1. TrendPlot Display

3-15
DMM4040/4050
Users Manual

To stop the TrendPlot session, press B or the STOP soft key.

To start the TrendPlot session over, press the STOP soft key followed by the
RESTART soft key.

Using the Histogram Function

The Histogram function provides a graphical representation of the standard deviation of a
series of measurements. The right two-thirds of the Meter’s display is used as a bar graph
chart. The vertical axis is a relative measure of the number of readings while 10 vertical
bars represent the standard deviation across the horizontal axis. The two center bars
indicates the number of readings that fall on either side of the average reading within the
1st standard deviation. The two bars on either side of the center two bars represent the
number of readings that fall within the 2nd standard deviation. The next two represent the
3rd standard deviation and so on to the 5th standard deviation.
The histogram function is helpful in looking at the standard distribution of the UUT.
While observing the bar graph display (see Figure 3-2), adjust the UUT variable control
to peak the center two bars of the histogram.

F1 F2 F3 F4 F5

caw056.eps
Figure 3-2. Histogram Display

In addition to the bar graph, the left third of the display also displays the number of
samples, the average, and standard deviation values.
To start a histogram session:
1. Set up the Meter for the desired measurement by selecting the function, and
connecting the signal to the Meter’s input.
2. With the Meter taking measurements, press J.
3. Press HISTOGRAM to start the session.
The display will start adjusting the bar graph as the number of readings accumulates. The
mean and standard deviation values also change in accordance with the collected
readings.
To start the histogram session over, press the STOP soft key followed by the
RESTART soft key.
To stop the histogram session, press B or the STOP soft key.

Controlling Trigger Functions

The Meter’s trigger functions allows you to select a measurement trigger source, set the
number of measurements (samples) per trigger, and set the delay time between receiving
the trigger and the start of a measurement. In addition, the trigger function provides a
“measurement complete” signal on the trigger port on the rear panel. See item 5 in
Table 3-3. Triggering the Meter remotely through one of its communication interfaces is

3-16
 Front-Panel Operation
Controlling Trigger Functions 3
covered in the Programmers Manual. The following sections discuss triggering the Meter
automatically (internal trigger), or externally using the trigger key on the front panel and
the trigger connector on the rear-panel.
Setup and control of the trigger function is accessible through the Meter’s Measurement
Setup key L.

Choosing a Trigger Source

There are four possible sources for triggering a Meter measurement: automatic, front
panel trigger key W, external, and remote. With the exception of remote triggering,
trigger source selection is through the trigger menu, found under the measurement setup
menu.
To select a trigger source:
1. Press L to see the measurement setup menu.
2. Press the TRIGGER soft key to reveal the trigger control selections.

Note
Setting the Meter to trigger via a remote command is only accessible
through the remote interface. See the “Triggering” section in the
Programmers Manual for more information on remote triggering.

Auto Triggering
In auto trigger mode, the Meter’s measurements are triggered by internal circuitry. These
triggers are continuous and occur as fast as the configuration will allow. Auto triggering
is the Meter’s power-on trigger source.
To return the Meter to auto trigger mode,
1. Press L.
2. Press the soft key labeled TRIGGER. If the Meter is in external trigger mode, the
soft key label EXT TRIG will be highlighted in the display.
3. Press the soft key labeled EXT TRIG.

External Triggering
In the external trigger mode, a Meter measurement starts each time a low-true pulse is
sensed on the external trigger connector or the front-panel trigger key W is pressed. For
each trigger or pulse received, the Meter will take the specified number of measurements
after the specified trigger delay.

Note
The trigger key is disabled whenever the Meter is in Remote mode.
To set up for an external trigger:
1. Press L.
2. Press the soft key labeled TRIGGER.
3. Press the soft key labeled EXT TRIG.
The Ext Trig soft key label will remain highlighted to indicate the Meter is in
external trigger mode. To return to auto trigger mode, press EXT TRIG again.

3-17
DMM4040/4050
Users Manual

If the Meter does not receive a trigger for a few seconds, a TRIG annunciator
illuminates indicating the Meter is waiting for a trigger and a lightning bolt appears
indicating the Meter does not know what voltage is applied to the terminals. Each
press of the trigger key W or an active low pulse on the trigger port will initiate a
measurement.

Setting the Trigger Delay

A Meter measurement can be delayed a set amount of time after receiving a trigger. This
feature may be useful when you need to wait for a signal to settle before measuring it.
When a trigger delay is specified, that delay is used for all functions and ranges.
To set a trigger delay:
1. Press L.
2. Press the soft key labeled TRIGGER.
3. Press the soft key labeled SET DELAY.
The trigger delay can be set between 0 and 3600 seconds with a resolution of 10
microseconds.
4. To select a specific digit to adjust, press either <-- or -->.
With the desired digit selected, press the soft key labeled -- to decrement the digit
or ++ to increment the digit.
5. With the desired delay set, press the soft key labeled ENTER.

Setting the Number of Samples

Normally, the Meter takes one measurement (or sample) each time a trigger is received if
in “wait-for-trigger” state. However, you can set the Meter to take a specified number of
measurements for each trigger.
To set the number of samples per trigger:
1. Press L.
2. Press the soft key labeled TRIGGER.
3. Press the soft key labeled #SAMPLES.
The number of samples per trigger can be set between 0 and 50000 samples.
4. To select a specific digit to adjust, press either <-- or -->.
With the desired digit selected, press the soft key labeled -- to decrement the digit
or ++ to increment the digit.
5. With the desired delay set, press the soft key labeled ENTER.

Understanding the Measurement Complete Signal

The trigger port on the Meter’s back panel provides a low-true pulse at the completion of
each Meter measurement. See the specifications section for more details on this signal.

Accessing and Controlling Memory

The Meter stores readings and meter configuration information using internal and
external memory. The external memory connects through the USB port on the front panel
of the Meter. Optional Memory in various storage capacities is available from Tektronix.
See the “Options and Accessories” section in Chapter 1 for Tektronix part numbers. In

3-18
 Front-Panel Operation
Controlling Trigger Functions 3
addition to storing and recalling readings and configurations, a memory management
function is available to delete files.
To access the Memory functions, press the M key. The memory menu appears over
the five soft keys: RECALL CONFIG, RECALL READING, STORE CONFIG,
STORE READINGS, and MANAGE MEMORY.

Storing Readings in Memory

The Meter will hold up to 9999 readings in one internal memory file. With external
memory, the Meter will hold 999 additional readings files, each of which will store up to
10000 readings.
To store readings in internal memory:
1. Press M.

+ 0.5993
F1 F2 F3 F4 F5
caw032.eps

2. Press the STORE READINGS soft key shown above.

3. If not already highlighted, press the INTERNAL MEMORY soft key.
4. Press the #SAMPLES soft key.
5. To adjust the number of samples, press either <-- or --> to select a digit.
With the desired digit selected, press the soft key labeled -- to decrement the digit
or ++ to increment the character. When 2nd Meas is enabled, each primary and
secondary reading is counted as a sample and appears in a separate line/row in the
readings file.
6. With the desired number of samples set, press the ENTER soft key to return to the
store readings menu.
7. Press the START soft key to initiate measurement storing. The START soft key
will change to STOP which can be pressed to stop the storage process. When the
requested number of samples have been stored, the soft key label changes back to
START. The MEM annunciator in the display also illuminates while readings are
being stored.

Note
For internal storage of readings, the number of readings stored will not
exceed 9999 readings regardless of the value set for number of samples.

3-19
DMM4040/4050
Users Manual

To store readings in external memory

1. Press M.
2. Press the STORE READINGS soft key.
3. Press the USB soft key.
4. Press the #SAMPLES soft key.
5. To adjust the number of samples, press either <-- or --> to select a digit.
With the chosen digit selected, press the soft key labeled -- to decrement the digit
or ++ to increment the character.
6. With the number of samples set, press the ENTER soft key to return to the Store
Readings menu.
7. Press the START soft key to begin storing measurements. The START soft key will
change to STOP which can be pressed to stop the storage process. When the
requested number of samples have been stored, the soft key label changes back to
START. The MEM annunciator in the display also illuminates while readings are
being stored.

Note
Each memory file will store up to 10000 readings. If the number of samples
is set to a value greater than 10000, consecutive memory files will be used
to store all the samples. If the readings fill the last file (999), reading
storage will stop.

Recalling Readings from Memory

To recall readings from internal memory:
1. Press M.
2. Press the RECALL READING soft key.
The Meter displays the first stored reading from the internal file. Four soft keys
provide the means to scroll through the readings stored in the file. The FIRST soft
key displays the first reading in the file while the LAST soft key displays the last
reading. Use the <-- and --> soft keys to move forward and backward through the
file one reading at a time.
To recall readings from external memory, the memory device must be removed from the
Meter and plugged into a PC where the comma delimited files can be read. Each file is
labeled MEAS0XXX.CSV. The XXX is the file number starting at 001 and going up to
999. Each file is date and time stamped.

3-20
 Front-Panel Operation
Controlling Trigger Functions 3
Storing Meter Configuration Information
Up to five meter configurations can be stored in the Meter’s internal memory. An
additional 99 configurations can be stored in the external memory with optional USB
memory installed.
To store a meter configuration in the Meter’s internal memory:
1. Press M.
2. Press the STORE CONFIG soft key as shown below.

+ 0.5993
F1 F2 F3 F4 F5
caw033.eps

3. Press the STORE INT MEM soft key.

4. Press one of the five soft keys labeled with the desired memory location to store the
present Meter configuration.
To store a meter configuration in to optional external memory:
1. Press M.
2. Press the STORE CONFIG soft key.
3. Press the STORE USB soft key.
The Meter labels the first four soft keys with the first four memory locations.
CONFIG01 through CONFIG04. The fifth soft key is labeled MORE to allow
access to all 100 memory locations.
4. To store the present Meter configuration in one of the first four memory locations,
press the appropriate soft key. If you want to store the present Meter configuration in
a location other than the first four locations, press the MORE soft key.
The display indicates the next available memory location. If all configuration
memory locations are filled, the Meter will always indicate memory location 10.
5. To adjust the display to the desired memory location, press either <-- or --> to
select a specific digit.
With the digit selected, press the soft key labeled -- to decrement the digit or ++ to
increment the digit.
6. With the preferred memory location set, press the ENTER soft key to store the Meter
configuration.

3-21
DMM4040/4050
Users Manual

Storing the Power-up Configuration

To store the Meter’s present configuration as a power-up configuration:
1. Press M.
2. Press the STORE CONFIG softkey.
3. Press the STORE POWER-UP softkey.
The Meter configuration stored as a power-up configuration will be set whenever the
Meter is powered on.

Note
LAN port remote settings (address, hostname, DHCP, mask, etc.) are saved
separately when selected in each instrument, and are not included in
individually stored/copied configurations.

Recalling the Power-up Configuration

In addition to having the power-up configuration to set up the Meter at power on, the
power-up configuration can be recalled through the front-panel keys. To recall the power-
up configuration:
1. Press M.
2. Press the RECALL POWER-UP softkey.

RECALL CONFIG

RECALL
1.4748
RECALL
USB INT MEM
F1 F2 F3 F4 F5
caw063.eps

3. Press the RECALL CONFIG softkey.

Note
The RECALL POWER-UP softkey will only appear when a power-up
configuration has been saved in the Meter’s memory.

Removing the Power-up Configuration

To remove the Meter’s stored power-up configuration:
4. Press M.
5. Press the STORE CONFIG softkey.
6. Press the REMOVE POWER-UP softkey.
After removing the power-up configuration, power the Meter down and back up using the
rear-panel power switch to restore factory default settings.

3-22
 Front-Panel Operation
Controlling Trigger Functions 3
Recalling a Meter Configuration
To recall a configuration from internal memory:
1. Press M.
2. Press the RECALL CONFIG soft key.
3. Press the RECALL INT MEM soft key.
4. Press the soft key labeled with the memory location (CONFIGA through
CONFIGE).
To recall a configuration from external memory:
1. Press M.
2. Press the RECALL CONFIG soft key.
3. Press the RECALL USB soft key.
The Meter labels the first four soft keys with the first four memory locations
CONFIG01 through CONFIG04. The fifth soft key is labeled MORE to allow
access to all 100 memory locations.
4. To recall the Meter configuration from one of the first four memory locations, press
the appropriately labeled soft key. If you want a memory location other than the first
four locations, press the MORE soft key.
The display indicates the last memory location containing a Meter configuration. If
all configuration memory locations are filled, the Meter will always indicate memory
location 10.
5. To select the memory location, press either <-- or --> to select a specific digit.
With the digit selected, press the soft key labeled -- to decrement the digit or ++ to
increment the digit.
6. Once the chosen memory location is set, press the ENTER soft key to recall that
Meter configuration.

Note
Incompatible configurations (from incompatible configuration versions)
will not be loaded, but will generate error +229 "Incompatible
measurement configuration not loaded".

Managing Memory
The Meter provides a method of clearing internal memory and displaying the status of
external memory. Per Department of Defense requirements, the Meter allows the erasure
of Meter configuration and data files from external USB memory modules. Other files are
not erased from the modules.
To copy the last or interrupted readings file from internal memory to an already-inserted
USB memory device:
1. Press M.
2. Press the INIT MEAS TO USB soft key.
The copy process will take several seconds.
To erase USB memory, refer to the “Media Memory” section in Chapter 1.

3-23
DMM4040/4050
Users Manual

To clear internal memory contents:

3. Press M.
4. Press the MANAGE MEMORY soft key as shown below.

9.30011 V~
F1 F2 F3 F4 F5
caw062.eps

5. Press the ERASE MEMORY soft key.

6. If you are sure you want to clear all stored readings, all stored configurations, the
user string and the hostname from internal memory, press the ERASE soft key. If
not, press the CANCEL soft key.
To check the amount of external memory available:
1. Press M.
2. Press the MANAGE MEMORY soft key.
3. Press the USB STATUS soft key.
After a few seconds, the Meter displays the total external memory, the amount of
external memory used and free external memory.

Controlling System-Related Operations

Identifying Meter Errors
When the Meter detects an error, the error annunciator (item 5 in Table 3-2) is
illuminated, and the beeper sounds. A list of possible Meter errors can be found in
Appendix B of this manual.
To read the error or errors:
1. Press I.
2. Press SYSTEM.
3. Press ERROR.
4. The first error, if there is more than one, is displayed. To read additional errors, press
NEXT.
If you want to erase all error messages without looking at each, press the CLR ALL soft
key.

Querying the Firmware for Revision Level

The Meter makes available the hardware version, software version, and serial number of
the instrument.
To view the versions and serial number:
1. Press I.
2. Press the soft key under SYSTEM.

3-24
 Front-Panel Operation
Controlling System-Related Operations 3
3. Press the soft key under VERSIONS + SN under the Setup menu.
The display shows the outguard software version (OutG SW), the inguard software
version (InG SW), the outguard hardware version (OutG HW) and the inguard
hardware version (InG HW). Also displayed is the Meter’s serial number
(Serial #).

Adjusting Display Brightness

Setting the brightness of the display is accessible through the Instrument Setup key.
To adjust display brightness:
1. Press I.
2. Press the SYSTEM soft key.
3. Press the BRIGHT soft key.
4. Press one of the soft keys under LOW, MEDIUM, and HIGH.
5. Press B to return to the previous menu.

Setting the Meter’s Date and Time

1. Press I.
2. Press the SYSTEM soft key.
3. Press the DATE TIME soft key.
4. To adjust the display to the desired date and time, press either <-- or --> to select
a specific digit or the month.
With the desired digit or month selected, press the soft key labeled -- to decrement
the digit or ++ to increment the digit.
5. Press the ENTER soft key to set the date and time and return to the system menu.

USB Operation
The USB memory operation offers a variety of capabilities. As an example, a USB device
can be used to store readings either directly from the A/D or by transferring readings
from internal memory. The data stored in the USB memory device is in a comma
delimited (CSV) format.

USB Storage Capacity and Write Time

The USB storage limit is 50,000 readings every time START is pressed (F1 soft key
press). Previous versions stored 50,000 readings in 10 files, each with 5,000 readings.
This version stores 50,000 readings in five files, with 10,000 readings each.
If storing readings to the USB memory device is not completed (or is interrupted by
changing function, NPLC, remote...), press MEMORY, MANAGE MEMORY,
INIT MEAS TO USB so volatile readings in internal memory are stored to the USB.
If STOP is selected during storage to the USB device, readings in internal memory will
be written directly to the device. Note that this may take several seconds. A USB memory
device should never be removed while a write is occurring.
The data is initially stored in internal memory and then transferred to the USB memory
device. For large data samples (i.e. > 10,000 readings), when 10,000 readings have been
stored in the internal memory, the data will be transferred to the USB memory device.

3-25
DMM4040/4050
Users Manual

The front panel display shows “BUSY WRITING USB" during the write. For
10,000 samples, the write time will typically take ~14 seconds.
In ACV, you can press dB, dBm, or zero while data is being stored. Units (and dgC, dgF,
K etc) can be changed in the middle of a USB readings file as well.
Each *.CSV file stored or copied to the USB memory device shows the date + time of the
first sample line/row and the date + time of the last sample in each file.

Note
Readings are not stored during the time each file is written to USB memory
stick, which can take 7 - 15 seconds. As a result, when storing more than
10,000 readings, there will be data gaps during the time the file is written
to the USB memory device.

Note
When using Mx+B and other math functions, the internal sampling rate is
slowed to permit data collection without loss. As an example, with Mx+B
active, the maximum dcV storage rate is ~340 reading/s.

USB Memory Device Compatibility and Special Instruction

After inserting a USB memory device (Mass Storage Device) into the Meter, wait
5+ seconds for the USB memory to be mounted before initiating any memory or
measurement activity.
Press [MEMORY], MANAGE MEMORY, and USB STATUS to verify a USB memory
device is readable by the Meter Not all USB memory devices are usable. Devices that try
to upload their own driver are generally not compatible.
Wait 3 or more seconds after the USB memory device light stops indicating any activity
before removing the USB memory device. Powering the Meter down or removing the
USB memory device prematurely can leave the USB memory device unreadable.

Configuring the Remote Interface

Selecting an interface port, setting up the ports, and selecting the command set the Meter
will recognize is accomplished through the Instrument Setup key. For information on the
commands that will remotely control the Meter, refer to the Programmers Manual.

Sample Program Using the RS-232 Computer Interface

Figure 3-3 is an annotated BASIC A program written for a PC that demonstrates how the
Meter can be used with the RS-232 computer interface. (See Fluke 45 Emulation Mode in
Chapter 2).

3-26
 Front-Panel Operation
Sample Program Using the RS-232 Computer Interface 3

gdb23f.eps
Figure 3-3. Sample Program for RS-232 Computer Interface

3-27
DMM4040/4050
Users Manual

Checking the Meter’s Calibration Date

To read the Meter’s calibration date:
1. Press I
2. Press the CAL soft key as shown below.

+ 0.5993
F1 F2 F3 F4 F5
caw034.eps

3. Press the CAL DATE soft key to display the date the Meter was last calibrated.
4. Press B to go back to the previous menu.

Note
UNLOCK CAL allows entry of a password so authorized personnel can
calibrate the Meter or change the (CAL) USER STRING.

Note
CAL USER STRING can be changed/entered after UNLOCK CAL. The
string also appears on the top line/row of the stored readings files.

Resetting the Meter’s Default Settings

To reset the Meter’s default settings:
1. Press I to see the instrument setup menu.
2. Press the RESET soft key to reset the Meter.

Note
Pressing the reset soft key will restore the Meter to the stored Power-up
configuration if defined, otherwise it will reset to the Meter factory default
settings.

3-28
 Chapter 4
Making Measurements

Title Page

Introduction........................................................................................................4-3
Selecting Function Modifiers.............................................................................4-3
Activating the Secondary Display .....................................................................4-3
Measuring Voltage.............................................................................................4-4
Measuring DC Voltage..................................................................................4-4
Measuring AC Voltage..................................................................................4-6
Measuring Frequency and Period ......................................................................4-7
Measuring Resistance ........................................................................................4-8
Making a Two-wire Resistance Measurement ..............................................4-8
Making a Four-wire Resistance Measurement ..............................................4-9
Measuring Current .............................................................................................4-10
Measuring DC Current ..................................................................................4-12
Measuring AC Current ..................................................................................4-13
Measuring Capacitance (4050 only) ..................................................................4-14
Measuring RTD Temperature (4050 only) ........................................................4-15
Testing Continuity .............................................................................................4-16
Checking Diodes................................................................................................4-17
Making a Triggered Measurement.....................................................................4-18
Setting the Trigger Mode...............................................................................4-18
Setting a Trigger Delay .................................................................................4-19
Setting Number of Samples per Trigger........................................................4-19
Connecting an External Trigger ....................................................................4-19
Monitoring the Measurement-Complete Signal.................................................4-20

4-1
DMM4040/4050
Users Manual

4-2
 Making Measurements
Introduction 4
Introduction
XW Warning
To avoid possible electrical shock, and/or damage to the Meter,
• Read the safety information found in Chapter 1 before
operating this meter.
• Do not apply more than 1000 volts between any terminal
and earth ground.
This chapter covers the steps for making a measurement with each of the Meter’s
functions. These steps include making a proper and safe connection between the Meter
and the circuit, as well as the manipulation of the front-panel controls to display the
selected measurement.
If you are unfamiliar with the front-panel controls, review the relevant sections in
Chapter 3.

Selecting Function Modifiers

Most of the functions described in this Chapter will have choices for changing how the
measured value is displayed or how the input signal is processed. These “Function
Modifiers” appear in the bottom line of the display as soft key labels. The available
selections are dependent on the selected function and are described in the Meter function
descriptions provided in this Chapter.

Activating the Secondary Display

For most of the Meter’s functions, an additional measured parameter may appear in the
display. These additional parameters are available when 2ND MEAS appears over one
of the soft keys.
The secondary measurement may be another parameter of the primary signal (e.g., ac
voltage and frequency of one signal), or a measurement of another signal made
simultaneously with the primary signal (e.g., dc voltage and dc current).
The range of the secondary display is always automatically controlled.
To select a secondary measurement:
1. Press the soft key labeled 2ND MEAS.
Each additional press of this soft key will cause the secondary display to cycle
through the available measurements. After the last secondary measurement is shown,
the next press of this soft key turns the secondary display off.

Note
When switching between Meter functions, the secondary display selection
for the function you last selected is deactivated the next time that function is
selected.

4-3
DMM4040/4050
Users Manual

Measuring Voltage
The Meter is capable of measuring up to 1000 V dc, 750 V ac (4040) or 1000 V ac
(4050).

W Caution
To avoid blowing the current fuses and possible damage to
other equipment, do not apply voltage to the meter’s input until
the test leads are properly connected to the input, and the
proper voltage function selected.

Measuring DC Voltage
To make a dc voltage measurement:
1. Press E.
The dc voltage icon | will appear to the right of the displayed value as shown
below.

-0.001698 V
F1 F2 F3 F4 F5
caw021.eps

2. Connect the test leads to the Meter’s inputs as shown in Figure 4-1.
3. Connect the test leads to the circuit and read the measured voltage in the Meter’s
display.

INPUT SENSE
V 4W
2W/4W
2

HI HI

1000 V CAT I 300V

Circuit 600V CAT II

Under LO LO
1V
Test FUSED

400 10A
mA

REAR FRONT

caw019.eps
Figure 4-1. Input Connections for Voltage, Resistance, and Frequency Measurements

4-4
 Making Measurements
Measuring Voltage 4
Function modifiers:
D FLTR A filter for quieting noisy measurments. This filter averages readings
to reduce reading noise when in immedicate trigger mode or when in
trigger mode with an unending number of triggers selected. The filter
is only available for dc functions at rates slower than 1 PLC. The
number of readings averaged by the digital filter varies with dc
function and range.
A FLTR A 3-pole analog filter for improving noise immunity. The filter is
active when this soft key label is highlighted and will increase
stabilization time of the measurement. See Appendix D for more
information on when to use the analog filter.

Note
For best results, the filter may require zeroing the
function when used.
RATIO DC measurement voltage divided by dc reference voltage. For dc
ratio, connect the reference HI/LO to the Meter’s HI/LO sense
terminals and the measurement voltage to the Meter’s HI/LO input
terminals. Note the specified measurement range applies to the input
terminals only.

Note
For best results in RATIO, the two input commons must
be shorted at the Meter terminals. The analog filter
(A FLTR) should be off.
2ND MEAS Cycles the secondary display through the measurement functions
listed below, and then off. When a second measurement function is
selected, the 2ND MEAS soft key label is highlighted.
VAC - Displays the ac signal riding on the measured dc voltage.

Note
DCV/ACV dual mode should not be used at frequencies
below 20 Hz.
See the “Range Keys” section in Chapter 1 to learn how to switch between auto and
manual ranging.

4-5
DMM4040/4050
Users Manual

Measuring AC Voltage
To make an ac voltage measurement:
1. Press A.
The ac voltage icon VB will appear in display as shown below.

0.3861 mV~
F1 F2 F3 F4 F5
caw022.eps

2. Connect the test leads to the Meter’s input as shown in Figure 4-1.
3. Connect the test leads to the circuit and read the measured voltage in the Meter’s
display.
Function modifiers:
Filter Displays the filter menu. For best accuracy and stable readings,
choose a filter based on the lowest frequency to be measured and the
performance needed.
3HZ SLOW Provides higher measurement accuracy on ac signals
between 3 Hz and 20 Hz. However, the measurement
cycle time is longer than it is when using the 20 Hz
filter.
20HZ Provides higher measurement accuracy on ac signals
between 20 Hz and 200 Hz. The measurement cycle
time is longer, however, than it is when using the
200 Hz filter.
200HZ Provides accurate measurements on ac signals 200 Hz
and above.
dB Displays the measured voltage as a decibel value referenced to a
stored relative value (dB = 20 log(Vnew/Vstored). The stored value is
obtained from the first measurement the Meter makes after pressing
the dB soft key. All future measurements are displayed using the
stored value as an offset. To take the Meter out of dB mode, press the
dB soft key.
dB€ Displays the measured voltage as a power decibel value referenced to
1 milliwatt (dBm = 10 log(power of Vnew into the reference
resistance / 1 mW) or 10 log(V2/R*1 mW) where R is the resistance.
To accommodate the various impedances that a dBm measurement
can be made across, the Meter allows for the selection of 21 different
impedance values.
To set the dB reference impedance:
1. Press L.
2. Press the soft key labeled dB€ Ref.

4-6
 Making Measurements
Measuring Frequency and Period 4
The available impedance settings are presented in sets of three
values. To move to a higher set of impedance values, press ++
-->. Press <-- -- to go to a lower set of impedance values.
3. With the impedance highlighted, press the soft key under the
value selected.
2ND MEAS Cycles the secondary display through the measurement functions
listed below, and then off. When a second measurement function is
selected, the 2ND MEAS soft key label is highlighted.
VDC - Displays the dc voltage on which the ac signal may be riding.

Note
ACV/DCV dual mode should not be used at frequencies
below 10 Hz.
Frequency - Displays the frequency of the ac signal applied to the
Input HI and LO connectors of the Meter.

Measuring Frequency and Period

The Meter measures the frequency, or period of ac signals between 3 Hz and 1 MHz,
applied between the Meter’s HI and LO connectors.
The G key not only activates the Meter’s Frequency/Period function, but also toggles
the Meter’s primary display between the signal’s frequency and period measurement.
Therefore, whether a frequency or period measurement appears after pressing G
depends on the condition this function was left in the last time it was used.
To make a frequency measurement:
1. Press G.

0.000000 Hz
F1 F2 F3 F4 F5
caw06f.eps

If S is displayed, press G again to switch the primary display to frequency.

2. Connect the Meter to the signal as shown in Figure 4-1.
To make a period measurement:
1. Press G.
If HZ is displayed, press G again to switch the primary display to period.
2. Connect the Meter to the signal as shown in Figure 4-1.

Note
Each press of G switches the measurement between frequency and
period.

4-7
DMM4040/4050
Users Manual

Function modifiers:
APERTURE Displays three different gate time selections: 0.01, 0.1 and 1 second.
These selections set the minimum amount of time the Meter takes to
measure frequency. Shorter gate times result in lower measurement
resolution.
2ND MEAS Cycles the secondary display through the measurement functions
listed below, and then off. When a second measurement function is
selected, the 2ND MEAS soft key label is highlighted.
Period – If a frequency measurement is in the primary display, the
period of the signal appears in the secondary display when the
2ND MEAS soft key is pressed.

Measuring Resistance
The Meter is capable of making two-wire and four-wire resistance measurements. Two-
wire measurements are easy to set up, and will make accurate measurements in most
applications. In a two-wire resistance measurement, both the source current and sensing
is done through the INPUT HI and LO terminals. A four-wire resistance measurement
will source current through the INPUT HI and LO terminals and use the SENSE HI and
LO to measure the resistance.

Making a Two-wire Resistance Measurement

To make a two-wire resistance measurement:
1. Connect the test leads to the Meter’s input connectors as shown in Figure 4-1.
2. Press N.

0.206220MΩ
F1 F2 F3 F4 F5
caw030.eps

3. If not already highlighted as shown above, press the 2W 2WX4W soft key.
Function modifiers:
D FLTR A filter for quieting noisy measurments. This filter averages readings
to reduce reading noise when in immedicate trigger mode or when in
trigger mode with an unending number of triggers selected. The filter
is only available for dc functions at rates slower than 1 PLC. The
number of readings averaged by the digital filter varies with dc
function and range.
A FLTR A 3-pole analog filter for improving noise immunity. The filter is
active when this soft key label is highlighted and will increase
stabilization time of the measurement. See Appendix D for more
information on when to use the analog filter.

4-8
 Making Measurements
Measuring Resistance 4
Note
For best results, the filter may require zeroing during the
ohms function.
Refer to the “Range Keys” section in Chapter 3 of this manual for information on how to
adjust the measurement range.

Making a Four-wire Resistance Measurement

The Meter incorporates two methods of making a four-wire resistance measurement. The
traditional method is to use four meter leads to connect the Meter to the resistance to be
measured. The optional 2X4 Wire test leads simplifies the four-wire measurement so you
only have to plug in two test leads to the front-panel Input HI and LO connectors of the
meter.
To make a four-wire resistance measurement using four test leads:
1. Connect the test leads to the Meter’s input connectors as shown in Figure 4-2.
2. Press N.

0.217384
F1 F2 F3 F4 F5
caw031.eps

3. If not already highlighted as shown above, press the 4WIRE soft key to switch to a
four-wire measurement.

INPUT SENSE
V 4W
2W/4W
2

HI HI

1000 V CAT I 300V

600V CAT II

LO LO
1V
FUSED

400 10A
mA

REAR FRONT

caw023.eps
Figure 4-2. Input Connections for 4-wire Resistance Measurements

4-9
DMM4040/4050
Users Manual

To make a four-wire resistance measurement using Tektronix’s 2X4 test leads:

1. Connect the test leads to the Meter’s input connectors as show in Figure 4-3.
2. Press N.
3. If not already highlighted, press the 2X4WIRE soft key.

INPUT SENSE
V 4W
2W/4W
2

HI HI

1000 V CAT I 300V

600V CAT II

LO LO
1V
FUSED

400 10A
mA

Ground tab REAR FRONT

caw060.eps
Figure 4-3. Input Connections for 4-wire Ohms Using 2x4 Wire Leads

Function modifiers:
D FLTR A filter for quieting noisy measurments. This filter averages readings
to reduce reading noise when in immedicate trigger mode or when in
trigger mode with an unending number of triggers selected. The filter
is only available for dc functions at rates slower than 1 PLC. The
number of readings averaged by the digital filter varies with dc
function and range.
A FLTR A 3-pole analog filter for improving noise immunity. The filter is
active when this soft key’s label is highlighted.
Refer to the “Range Keys” section in Chapter 3 of this manual for information on how to
adjust the measurement range.

Measuring Current
The Meter is capable of making both ac and dc current measurements up to 10 A. Two
separate input connectors, in conjunction with the LO connector, are used for current
measurements. For best resolution, current measurements not exceeding 400 mA should
be made using the LO and mA input connectors as shown in Figure 4-4.

4-10
 Making Measurements
Measuring Current 4
W Caution
To avoid blowing the current input fuse or possibly damaging
the Meter:
• Current measurements between 400 mA and 10 A should be
measured using only the 10 A and LO input connectors.
• BEFORE applying power to the circuit to be measured,
ensure the test leads are correctly connected to the Meter
inputs appropriate for the expected current.
• Exceeding 440 mA on the 400 mA input connector or
exceeding 11 A on the 10 Amp connector will blow the
internal fuse.
Current measurements expecting to be between 400 mA and 10 A are made using the
Input LO and 10A input connectors as shown in Figure 4-5.

I < 400 mA V
INPUT SENSE
4W
2W/4W
2

HI HI

1000 V CAT I 300V

600V CAT II

LO LO
1V
FUSED

V AC 400
mA 10A

REAR FRONT

caw025.eps
Figure 4-4. Input Connections for Current Measurements Below 400 mA

I > 400 mA
and V
INPUT SENSE
4W
I < 10 A 2W/4W
2

HI HI

1000 V CAT I 300V

600V CAT II

LO LO
1V
FUSED

400
V AC mA 10A

REAR FRONT

caw026.eps
Figure 4-5. Input Connections for Current Measurements Above 400 mA

4-11
DMM4040/4050
Users Manual

Refer to the “Range Keys” section in Chapter 3 of this manual for information on how to
adjust the measurement range.

Measuring DC Current
To measure dc current:
1. Connect the test leads between the Meter’s input connectors and the measured circuit
as shown in Figure 4-4 for currents 400 mA or less or Figure 4-5 for currents up to
10 amps.
2. Press H.

0.0086
F1 F2 F3 F4 F5
caw09f.eps

3. With the test leads connected to the 400 mA and Input LO connectors, press the€A
soft key as shown above, if not already highlighted. If the test leads are connected to
the 10A and Input LO connectors, then press the 10A soft key.
4. Apply power to the measured circuit and read the current in the Meter’s display.

4-12
 Making Measurements
Measuring Current 4
Function modifiers:
D FLTR A filter for quieting noisy measurments. This filter averages readings
to reduce reading noise when in immedicate trigger mode or when in
trigger mode with an unending number of triggers selected. The filter
is only available for dc functions at rates slower than 1 PLC. The
number of readings averaged by the digital filter varies with dc
function and range.
A FLTR A 3-pole analog filter for improving noise immunity. The filter is
active when this soft key label is highlighted and will increase
stabilization time of the measurement. See Appendix D for more
information on when to use the analog filter.

Note
For best results, the filter may require zeroing during the
current function.
2ND MEAS Cycles the secondary display through the measurement functions
listed below, and then off. When a second measurement function is
selected, the 2ND MEAS soft key label is highlighted.
ACI - Displays the ac current riding on the dc current measurement.
DCI/DCV – Displays the dc current and dc voltage present on the
input. To measure the voltage and current of an input signal requires
three leads. The voltage and current measurement must share the same
common lead. The resistance of the common lead combines with a
small amount of internal resistance in the meter to cause an IR drop
that affects the accuracy of the voltage measurement. Depending on
the circumstance, this effect can be substantial. As an example, 20
mΩ of lead resistance can cause more than 20 mV of additional error
at 1 A.

Note
Measurement of ac signals below 20 Hz is not recommended in DCI/ACI
dual mode. Use the ACI function for this measurement.

Measuring AC Current
To measure ac current:
1. Connect the test leads between the Meter’s input connectors and the measured circuit
as shown in Figure 4-4 or Figure 4-5, based on the anticipated level of current.
2. Press K.

0.0333uA~
F1 F2 F3 F4 F5
caw08f.eps

4-13
DMM4040/4050
Users Manual

3. With the test leads connected to the 400 mA and Input LO connectors, press the €A
soft key as shown above, if not already highlighted. If the test leads are connected to
the 10A and Input LO connectors, then press the 10A soft key.
4. Apply power to the measured circuit and read the current in the Meter’s display.
Function modifiers:
Filter Displays the filter menu. For best accuracy and stable readings,
choose a filter based on the lowest frequency to be measured and the
accuracy needed.
3HZ SLOW Provides higher measurement accuracy on ac signals
between 3 Hz and 20 Hz. However, the measurement
cycle time is longer than it is when using the 20 Hz
filter.
20HZ Provides higher measurement accuracy on ac signals
between 20 Hz and 200 Hz. However, the measurement
cycle time is longer than it is when using the 200 Hz
filter.
200HZ Provides accurate measurements on ac signals 200 Hz
and above.
2ND MEAS Cycles the secondary display through the measurement functions
listed below, and then off. When a second measurement function is
selected, the 2ND MEAS soft key label is highlighted.
IDC - Displays the dc current the ac signal is riding on.
Frequency - Displays the frequency of the ac signal on the Meter’s
current connectors (Input Lo and 400 ma or 10A) connectors.

Measuring Capacitance (4050 only)

The Tektronix 4050 is capable of measuring capacitance from 1 pF to 100 mF (0.1 F).
To make a capacitance measurement:
1. Press C. An example of the capacitance display is shown below.

0.000 nF
F1 F2 F3 F4 F5
caw10f.eps

2. With the leads open, press Z.

3. Connect the Meter’s test leads as shown in Figure 4-6.

4-14
 Making Measurements
Measuring RTD Temperature (4050 only) 4

INPUT SENSE
V 4W
2W/4W
2

HI HI

1000 V CAT I 300V

600V CAT II

LO LO
1V
FUSED

400 10A
mA

REAR FRONT

caw027.eps
Figure 4-6. Measuring Capacitance

Refer to the “Range Keys” section in Chapter 3 of this manual for information on how to
adjust the measurement range.

Measuring RTD Temperature (4050 only)

The Tektronix 4050 is capable of measuring temperatures between -200 °C and 600 °C
using Resistance Temperature Detectors (RTDs).
To make a temperature measurement:
1. Connect the RTD to the Input HI, and LO, then the SENSE HI and LO connectors
as shown in Figure 4-7.

INPUT SENSE
V 4W
2W/4W
2

HI HI

1000 V CAT I 300V

600V CAT II

LO LO
1V
FUSED

400 10A
mA

REAR FRONT

caw028.eps
Figure 4-7. Temperature Measurements

4-15
DMM4040/4050
Users Manual

2. Press T to display the measured temperature as shown below.

- 246.645 ºF
F1 F2 F3 F4 F5
caw11f.eps

To change the temperature scale, refer to the “Setting the Default Temperature Scale”
section in Chapter 3 of this manual. Available scales are Celsius, Fahrenheit, and Kelvin.
Refer to the “Adjusting the Meter’s Range” section in Chapter 3 of this manual for
information on how to adjust the measurement range.
Function modifiers:
4Wire Switches the measurement input connectors to 4-wire measurement
for 4-wire RTDs. 4-wire RTDs make more accurate measurements.
RTD 385 Default RTD type. All coefficients are predefined.
RO Used to select a different value of RTD resistance at 0 °C.
ALPHA Used to set the first coefficient of the Calendar-Van Dusen equation.
2ND MEA Cycles the secondary display through the measurement functions
listed below and then off.
OHMS - Displays the resistance of the RTD. 2-wire resistance is used
when in 2-wire temperature mode and 4-wire resistance when the
Meter is in 4-wire RTD mode.

Testing Continuity
Continuity testing determines whether a circuit is intact (i.e., has a resistance less than the
threshold). The threshold is selectable between 1 and 1000 Ω.
To perform a continuity test:
1. Press S on the 4050 or Q on the 4040. An example of the continuity display is
shown below.

OPEN
F1 F2 F3 F4 F5
caw12f.eps

Connect the test leads as shown in Figure 4-1.

Note
The Beeper cannot be disabled in continuity. Pressing BEEPER OFF turns
off the beeper for errors.

4-16
 Making Measurements
Checking Diodes 4
To set the threshold value, refer to the “Setting the Continuity Threshold Resistance”
section in Chapter 3 of this manual.
Function modifiers:
None

Checking Diodes
The diode function sends a current through a semiconductor junction while the Meter
measures the voltage drop across the junction (or junctions). Measurements are displayed
in the 10 V range at a relatively fast measurement rate. "OPEN" is displayed for voltages
10 % above the compliance voltage setting. Typical junction voltage drop on good
junctions are 0.3 to 0.8 volts. If enabled, the beeper will make a short beep when a good
junction is detected. Shorted diodes will indicate a significantly lower voltage.
With the higher compliance voltage (up to 10 V), the Meter’s diode test function can test
zeners up to 10 volts, diode stacks and LEDs. The selectable current and maximum
voltage allows you to tailor the diode test to the expected voltage for the junction being
tested.
To check a diode:
1. Press S twice on the 4050 or D once on the 4040. An example of the diode test
display is shown below.

+ 0.5994
F1 F2 F3 F4 F5

caw13f.eps

2. Select the test voltage and current appropriate for the diode being tested by pressing
the associated soft keys.
3. Connect the test leads as shown in Figure 4-8.

4-17
DMM4040/4050
Users Manual

INPUT SENSE
V 4W
2W/4W
2

HI HI

1000 V CAT I 300V

600V CAT II

LO LO
1V
FUSED

400 10A
mA

REAR FRONT

caw024.eps
Figure 4-8. Diode Testing Connections

Function modifiers:
None
Four soft keys allow changing the test voltage and current applied to the diode through
the test leads. The compliance voltage is set to either 5 volts or 10 volts. The compliance
current is set to either 1 mA or 0.1 mA. Press the appropriate soft key to select the desired
voltage and current setting.

Making a Triggered Measurement

Triggering the Meter’s measurement cycle is set through the trigger menu and performed
via a connection on the Meter’s rear panel or the front panel trigger key. The trigger
menu also allows setting a trigger delay and setting the number of samples or
measurement cycles taken for each trigger received. All trigger function parameters are
accessed through the measurement setup key.
Press Lto see the measurement setup menu.
A measurement trigger can also be initiated through the IEEE 488 port with a remote
command. This method of triggering is covered in the DMM4040/4050 Programmers
Manual.

Setting the Trigger Mode

The Meter’s measurement cycle can be initiated either by the internal measurement
circuit or by external stimulus.
To select the trigger mode:
1. With the measurement setup menu displayed, press the soft key labeled TRIGGER.
If EXT TRIG is highlighted, the Meter’s measurement cycle is triggered externally
either through the external trigger jack on the rear panel, or the trigger key on the
front panel. If EXT TRIG is not highlighted, then the Meter’s measurement cycle is
triggered automatically by its internal circuitry.
2. Press the soft key labeled EXT TRIG to toggle between internal and external
triggering.

4-18
 Making Measurements
Making a Triggered Measurement 4
Setting a Trigger Delay
When in external trigger mode, the Meter is capable of delaying the start of the
measurement cycle after the trigger stimulus is sensed by up to 3600 seconds.
To set a trigger delay:
1. With the measurement setup menu displayed, press the soft key labeled TRIGGER.
2. Press the soft key labeled TRIG DELAY.
3. Use the soft keys to set the trigger delay.
Select the digit in the value by pressing either <-- or -->.
With the desired digit selected, press the soft key labeled -- to decrement the digit
or ++ to increment the character.
4. Press ENTER.

Setting Number of Samples per Trigger

When in external trigger mode, the Meter will take between 1 and 50,000 measurements
for each trigger received.
To set the number of samples, or measurements the Meter will take for each external
trigger received:
1. Press Lto display the measurement setup menu.
2. Press the TRIGGER soft key.
3. Press the soft key labeled #SAMPLES.
4. Use the soft keys to set the number of samples between 1 and 50,000.
Select the digit in the value by pressing either <-- or -->.
With the digit selected, press the soft key labeled -- to decrement the digit or ++ to
increment the character.
5. Press ENTER.

Connecting an External Trigger

The TRIG I/O jack on the Meter’s rear panel is used to connect to an external trigger
signal. The falling edge of a TTL signal will trigger the Meter to start taking
measurements, if the Meter is in external trigger mode.
Figure 4-9 indicates the purpose of the three pins in the TRIG I/O connector.

TRIG I/O

Pin 1: Trigger In Pin 3: Measure Complete Out

Pin 2: Signal Ground

caw059.eps
Figure 4-9. TRIG I/O Pin-out Description

4-19
DMM4040/4050
Users Manual

Monitoring the Measurement-Complete Signal

In addition to being a trigger input, the TRIG I/O jack on the Meter’s rear panel also
provides a signal indicating the completion of a measurement cycle. A falling edge of a
TTL signal indicates a measurement cycle is complete. See Figure 4-9 above to identify
which pins on the TRIG I/O connector are used to sense the measurement-complete
signal.

4-20
 Appendices

Appendix Title Page

A 2X4 Test Leads ................................................................................................... A-1

B Errors................................................................................................................... B-1
C RS-232 Port Connections .................................................................................... C-1
D Analog Filter Applications .................................................................................. D-1
DMM4040/4050
Users Manual
 Appendix A
2X4 Test Leads

Introduction
The optional Tektronix TL705 test leads simplify making 4-wire ohms measurements by
integrating the HI+HI Sense and LO+LO Sense test leads into one cable. The Meter’s
Input HI and LO jacks consist of two contacts. One contact is connected to HI or LO
input circuits and the other contact is connected to the Sense input circuits. Like the input
jacks, the 2x4 test lead also has two contacts that align with the input jack contacts to
provide a four wire connection.

Ground tab

caw061.eps
Figure A-1. 2X4 Wire Test Leads

XW Warning
To avoid electric shock and possible damage to the Meter, use
the 2X4 Wire test leads as specified in the instruction sheet that
comes with the probes. Inspect the test leads before use. Do
not use them if insulation is damaged or metal is exposed.
Check the test leads for continuity. Replace damaged test leads
before using the Meter.
A-1
 DMM4040/4050
Users Manual

A-2
 Appendix B
Errors

Introduction
Listed below are the error messages the Meter uses to indicate a problem.
AC Line frequency too high
Invalid calibration step number
*TRG/GET received but was ignored
488.2 I/O deadlock
488.2 interrupted query
488.2 query after indefinite response
488.2 unterminated command
A fatal error occurred configuring the serial port
A fatal error occurred opening the serial port
AC Line frequency too low
Acknowledgement queue full
ACPOLE: all CAPDAC settings are too high
ACPOLE: all CAPDAC settings are too low
ACPOLE: no CAPDAC setting is close enough
Bad CRC
Bad keyword
Bad parameter value
Cal reference value out of tolerance
Cal secured
CAL? only works if you are calibrating
Calibration Aborted
Calibration measurements out of tolerance
Calibration steps out of sequence
CALibration:DATE not supported for the DMM
Can't get 1V/10V DC linearization constants

B-1
 DMM4040/4050
Users Manual

CCO constant name is bad

Character string was more than 12 characters
Command not allowed in local
Command only allowed in RS-232/Ethernet
Could not open guard crossing port
Could not open measurement file on USB device
Could not open the ethernet port
Could not save configuration
Could not save MAC address
Could not save network configuration
Data stale
Error occurred reading characters from Ethernet port
Error occurred reading characters from GPIB controller
Error occurred sending characters to the GPIB controller
Error occurred when purging memory
Error opening GPIB Controller
Error setting GPIB Primary Address
Error setting the RTC/System date
Error setting the RTC/System time
Ethernet port not available in Fluke 45 emulation mode
Function/2nd func mismatch
Function/math mismatch
Function/range mismatch
Generic Execution Error
Got out of sequence packet
GPIB Command byte transfer error
GPIB DOS Error
GPIB File System Error
GPIB I/O operation aborted (time-out)
GPIB Interface Board has not been addressed properly
GPIB Invalid argument
GPIB No capability for operation
GPIB No present listening devices
GPIB Non-existent GPIB board
GPIB Routine not allowed during asynchronous I/O operation
GPIB Serial poll status byte lost
GPIB Specified GPIB Interface Board is Not Active Controller
GPIB Specified GPIB Interface Board is not System Controller
GPIB SRQ stuck in ON position
GPIB Table problem
Guard crossing link failed to start
Guard crossing restarted
Illegal Data value was entered
Illegal/Unknown NPLC Selection
Illegal/Unknown TRIGGER Selection
Incorrect packet size from inguard
Info packet rec'd; link not active
Inguard Calibration Constant write failed
Inguard not responding (recv)
Inguard not responding (send)
INITiate received but was ignored
Instrument configuration load failed

B-2
 Appendices
Errors B
Instrument configuration store failed
Insufficient memory
Invalid dimensions in a channel list
Invalid parameter
Invalid parameter
Invalid response type from inguard
Invalid secure code
Invalid string data
Invalid suffix in command header
Line too long (greater than 350 characters)
Load reading from file failed
Lost sync with inguard
Math error during calibration
Measurement configuration load failed
Measurement configuration store failed
Measurement data lost
Missing or wrong number of parameters
No entry in list to retrieve
No error
No measurements taken during calibration
Not ACKing my packets
Numeric value is invalid
Numeric value is negative
Numeric value is real
Numeric value overflowed its storage
Overload at input during calibration
Oversize packet rec'd
Parameter is not a boolean type
Parameter is not a character type
Parameter is not a numeric type
Parameter is not an quoted string type
Parameter is not an unquoted string type
Parameter type detection error
Port value is out of range (1024 to 65535)
Present function is invalid for selected command
Quality indicator too low
RS-232 framing/parity/overrun error detected
Secondary function is not enabled
Secure code too long
Self Test Failed
Serial buffer full
Someone forgot to call begin (cal)
Someone forgot to call begin (ICONF)
Someone forgot to call begin (MCONF)
Store reading to file failed
String size is beyond limit
Suffix Error. Wrong units for parameter
Syntax error
Time out while taking data
Timeout error during calibration
Timeout occurred while opening the ethernet port
Too many dimensions to be returned

B-3
 DMM4040/4050
Users Manual

Too many errors

Tried to set invalid state
Tried to set invalid state
Trigger Deadlock
Trigger ignored (just like 34401)
Unable to access storage memory
Unknown ACK byte
Unknown Calibration Constant
Unknown control byte
Unknown error %d
Unknown Function Selection
Unknown Range Selection
Unmatched bracket
Wizard password is invalid
Wrong ACK number
Wrong number configuration acknowledgement
Wrong type of parameter(s)

B-4
 Appendix C
RS-232 Port Connections

Introduction
Table C-1 lists the pins and related signals available through the RS-232 port.

Table C-1. RS-232 Pin to Signal List

Pin Name Usage

1 DCD Not used

2 RX Receive data

3 TX Transmit data

4 DTR Not used

5 GND Signal ground

6 DSR Not used

7 RTS Request to send

8 CTS Clear to send

9 RI Not used

The Meter’s RS-232 control lines can be rewired to an alternate pairing instead of the
RTS/CTS control pair. This alteration should be done by a trained technician at a
Tektronix service center. Opening the cover of the Meter to make this alteration may void
the Meter’s warranty.

C-1
 DMM4040/4050
Users Manual

C-2
 Appendix D
Analog Filter Applications

Introduction
The Meter’s analog filter is intended to reduce the presence of external ac when making
dc measurements. Most applications do not require the use of this filter, but in some
situations it can be utilized to improve DC measurements. A good example of this is
using the filter when measuring the DC value of a signal with AC content, such as a DC
power supply voltage that has significant AC line ripple present.
The analog filter is not intended to reduce the internal noise within the DMM, and usually
has no affect in reducing noise when measuring an open circuit in DCI, measuring a short
circuit in DCV or Resistance, or measuring the output of a precision DC calibrator. In
fact, the analog filter may actually add to the noise in these situations, and often times
offsets the reading. Because of the latter phenomena, when the analog filter is used, the
DMM must first be Zeroed in the range, NPLC setting, and triggering approach used. If
your application makes it difficult to first ZERO the instrument, the offset can be
characterized, and the typical errors are shown in Tables D-1 through D-3 can be used.
For those ranges and NPLCs not shown, there are usually no additional errors associated
with using the analog filter.

Table D-1. DC Volts Analog Filter Errors

Range NPLC Additional Analog Filter Error

100 mVdc 1, 10 1.5 μV

0.2 12 μV
0.02 40 μV
100 Vdc 10, 100 0.0002 V
<10 0.001 V

D-1
 DMM4040/4050
Users Manual

Table D-2. Ohms Analog Filter Errors

Range NPLC Additional Analog Filter Error

10 Ω 10, 100 0.5 mΩ

<10 1.9 mΩ
100 Ω 10, 100 1.5 mΩ
<10 9.0 mΩ
100 kΩ 10, 100 0.6 Ω
<10 2.5 Ω

Table D-3. DC Current Analog Filter Errors

Range NPLC Additional Analog Filter Error

100 μA, 10 mA, 1 A 100 0.005 % of range

10 0.015 % of range
1 0.027 % of range
0.2 0.09 % of range
0.02 0.27 % of range
[1]
1 mA, 100 mA, 10 A 10 0.001 % of range
1 0.0025 % of range
0.2 0.009 % of range
0.02 0.026 % of range
[1] 3 A range uses the 10 A range errors.

D-2
 Index

DC Voltage
—A— Measurements, 4-4
Defaults, resetting of, 3-28
AC Voltage
Diode Test
Measurements, 4-6
checking of, 4-17
Analyze functions
setting compliance voltage, 3-10
Histogram, 3-16
setting of current, 3-10
Math
Display
Limits testing, 3-12
Brightness, setting of, 3-25
MX+B, 3-13
Panel elements, 3-5
Offset, 3-13
Resolution, Setting of, 3-9
Statistics, 3-11
TrendPlot, 3-14
—E—
—B— Equipment rack mounting, 2-8
Errors
Bail
List of, B-1
adjustment of, 2-7
Reading, 3-24
removal of, 2-7

—C— —F—
Filter
Calibration date
AC, 3-9
checking of, 3-28
DC
Capacitance measurements, 4-14
DC Current, 4-13
Cleaning the Meter, 2-8
DC Voltage, 4-5, 4-8, 4-10, 4-13
Clock
Resistance, 4-8
setting date and time, 3-25
Firmware
Configurations
checking revision, 3-24
recalling, 3-23
Frequency meausrements, 4-7
storing, 3-21
Front Panel, 3-4
Configure for Measurements, 3-8
Front Panel Navigation, 3-8
Continuity
Function modifiers, 4-3
Setting of threshold, 3-10
Fuses
Testing for, 4-16
Current input, 2-5
Current measurments
Line-Power, 2-4
AC, 4-13
DC, 4-12
—H—
—D— Historgram, 3-16
Date, setting of, 3-25
1
DMM4040 and DMM4050
Users Manual

—I— —P—
Input Impedance, Automatic, 3-10 Period measurements, 4-7
Inspecting Meter, 2-3 Product Description, 1-11

—K— —R—
Keys Range Key, 3-8
Range, 3-8 Readings
Soft, 3-4 recalling, 3-20
Soft, labels for, 3-6 storing, 3-19
Rear panel, 3-7
—L— Recalling configurations, 3-23
Recalling readings, 3-20
Limits Testing
Resistance measurements
setting of limits, 3-12
2-wire, 4-8
Using, 3-12
4-wire, 4-9
Line Voltage Selection, 2-3
Resistance Measurements, 4-8
RTD Temperature measurements, 4-15
—M—
Math functions —S—
Limits testing, 3-12
Secondary display
MX+B, 3-13
activation of, 4-3
Offset, 3-13
Shipping Meter, 2-3
Math Operations, 3-11
Specifications, 1-15
Measurement Complete
Statistics
Monitoring of, 4-20
taking of, 3-11
Understanding of, 3-18
Storing configurations, 3-21
Measurements
Storing Meter, 2-3
AC current, 4-13
Storing readings, 3-19
AC Voltage, 4-6
Capacitance, 4-14
Current, 4-10 —T—
DC current, 4-12 Temperature
DC Voltage, 4-4 setting default scale, 3-10
Frequency, 4-7 Temperature measurements, 4-15
Period, 4-7 Time, setting of, 3-25
Resistance, 4-8 TrendPlot, 3-14
2-wire, 4-8 Trigger functions, 3-16
4-wire, 4-9 Trigger sources, 3-17
Temperature, 4-15 Triggering
Voltage, 4-4 Auto, 3-17
Memory Choosing a source, 3-17
Configuration External, 3-17
Recall, 3-23 I/O jack, 4-19
Storing, 3-21 setting a delay, 4-19
management of, 3-23 Setting a delay, 3-18
Reading recall, 3-20 Setting number of samples, 3-18
Reading storage, 3-19 Setting the mode, 4-18
Memory, Access to, 3-18 Triggered Measurement, 4-18
Meter errors Turning power on, 2-7
Reading, 3-24
MX+B function, 3-13 —U—
Unpacking Meter, 2-3
—O—
Offset, setting of, 3-13 —V—
Options and Accessories, 1-14
Voltage

2
 Index (continued)

AC measurements, 4-6
DC measurements, 4-4

3
DMM4040 and DMM4050
Users Manual