Scribd
Upload
16 views18 pages

FEA Lab Report

Uploaded by

Jawad ahmed Khan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
16 views18 pages

FEA Lab Report

Uploaded by

Jawad ahmed Khan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 18

Finite Element Analysis

Lab Report

Submitted by:
Muhammad Rayyan Usmani
00000379090

Instructor:
Mr. Affan Ahmed
Contents
Lab 01 - Box ................................................................................................... 3
Lab 02 – Rectangular Cross Section ............................................................... 4
Lab 03 – I Beam .............................................................................................. 7
Lab 04 – T Beam with Convergence .............................................................. 11
Lab 05 – T Beam With & Without Sharp Edges ............................................. 14
Lab 06 – L Beam ........................................................................................... 17
Lab 07 – Box Mesh Convergence .................................................................. 18
Lab 01 - Box
Lab 02 – Rectangular Cross Section

Objective: To simulate 25 X 50 Rectangle Static Structurally


Step 1: Open Static Structural in Ansys Workbench

Step 2: Add Material in Engineering Data


Step 3: Select XY Plane and Use Look At Feature
In the sketching section, sketch a rectangle and give dimensions of 50m by 25m.

Then Extrude 1270mm:


Step 4: Generate Mesh

Step 5: Add Fixed Support and Force in the Analysis


Step 6: Solve the Study and Obtain Results
Lab 03 – I Beam
Objective: To design an I – Beam and perform static structural analysis.

Step 01:
Add Materials from Engineering Data Tab
1) Concrete
2) Titanium
3) Structural Stell

Step 02:
Open Design Modeller, From Concept Tab -> Insert I – Beam of dimensions 25X25X30 and
1X1X2.5

Step 03:
Open Mechanical and Generate Mesh of the I – Beam. (element size = 0.0010m)
Step 04:
Apply Constraints and Force:
1) Fixed Supports on 2 I – Faces
2) 1000N Force on the Upper Face

Step 05:
Solve to obtain results

Results
Concrete
Structural Steel

Titanium
Lab 04 – T Beam with Convergence
Objective: To perform analysis on a T – Beam with convergence.

Step 1: Material Addition


Add the material of own choice using isotropic elasticity and Young’s Modulus of 1840 GPA
and Poisson Ratio of 0.25

Step 2: Geometry
Create a T section and extrude, fillet the longer edges by 0.005m
Step 3: Mesh
Generate Mesh

Step 4: Loading Conditions


Make the T cross sections fixed and apply a torque at the bottom face
Step 5: Solution
Solve the model and add convergence of 15%

Applied Torque Max Von Mises Stress


25 69132
50 138266
75 207400
100 276530
Graph:

Python Code for Graph:


Lab 05 – T Beam With & Without Sharp Edges

Objective: To perform static structural analysis on a T Beam with and without sharp edges
Step 1:
Add Material form Engineering Data Tab

Step 2:
Make a T Beam with Appropriate dimensions in Design Modeler

Step 3:
Apply boundary conditions, fix the 2 T cross sections and apply different magnitudes of force
on the bottom face
Step 4:
Generate Mesh of the T beam

Step 5:
Solve to get the results and obtain maximum stress on different magnitudes of applied
forces

Step 6:
In the Design Modeler add fixed radius on sharp edges of 0.0035m
Step 7:
Repeat Steps 3 – 5 to obtain maximum stresses for different magnitudes of applied forces

Step 8:
Compare the maximum stresses
Lab 06 – L Beam
Lab 07 – Box Mesh Convergence

You might also like