pneumatic function

valves

www.legris.com
lock-out valves "safety"
moving cylinder (active pilot signal) blocked cylinder (pilot signal removed) 12

pilot pilot signal

signal removed 2
1
diaphragm diaphragm
spring spring to control valve
to control valve
(blocked)

piston piston

cylinder cylinder

exhaust exhaust

supply supply

signal authorizing disappearance

movement causes block

Designed to offer maximum flow capacity, Legris lock-out specifications:

valves lock the piston by simultaneously cutting off the supply suitable fluid: compressed air
and exhaust air. working pressure: 15 to 145 psi
Functional locks are more precise and rapid when lock-out working temperature: -4˚ to 160˚ F
valves are located on the cylinder: the volume of air in the
pipework no longer needs to be taken into consideration.
installation:
Mounted in pairs, lock-out valves are installed directly on the
cylinder. As they can be fully swivelled, their use provides
excellent flexibility in the design and installation of pneumatic
circuits.

manually operated 3-way venting valves "safety"

2 2
OPEN CLOSED
orientable 3 1
lever 1 3

lock nut supply to system to system

system vented
to atmosphere

valve open = free flow of air to system

(1) supply (1) supply

supply to system to system

(2) (2)

system system
pressure pressure
valve closed = supply shut-off, system vented to atmosphere
Examples with supply (1) - series 7805 - 7800

manually operated 3-way venting valves pneumatic slide valves:

Legris manual switch operated vent fitting guarantees Pneumatic slide valves may be used to effect isolation of
immediate isolation of the air line by venting the system to the air line by venting the system to atmosphere.
atmosphere by a simple manual operation of the lever. Their in-line configuration allows compact mounting directly
Easy to operate, it can be used whenever the system has to into the pipework.
be frequently vented. Completely orientable, a number of
valves can be mounted side by side, even in reduces spaces. specifications:
The sub-base seal and push-in connection outlet allow suitable fluid: compressed air
immediate installation. maximum working pressure: 230 psi
working temperature: 15˚ to 175˚ F
specifications:
suitable fluid: compressed air
maximum working pressure: 230 psi
working temperature: 15˚ to 175˚ F
pressure regulator fittings “energy efficient”
Legris pressure regulator fittings are used to stabilize the
adjustment pressure at a given value that is applied to pneumatic
screw equipment, whatever the fluctuations of pressure upstream.
(manual
or with The pressure outlet is fully controlled by an adjustment screw:
hex key) to assist pressure selection, the screw is calibrated showing
pressure setting levels.
outlet pressure Depending on the application, they may be mounted:
selection - between the cylinder and the control valve, for reduced
(in bar)
pressure in one direction.
- on the control valve, for reduced pressure in both directions.
- on the cylinder to manually adjust its operating force.

to system
specifications:
suitable fluid: compressed air
working pressure: input pressure: 15 to 230 psi
regulated pressure: 15 to 115 psi
working temperature: 15˚ to 160˚ F

supply

pneumatic slow start valves "safety"

adjustment by hex key 7860-7861-7864

gold colored identification washer
pressure speed regulator

spring
adjustable needle
valve

to system to system

system isolation valve

adjustment by hex key 7870-7871-7874

black identification washer
pressure speed regulator

spring
adjustable needle
valve

to component to component

isolated component

Pneumatic slow start valves allow air pressure to gradually Mounted to the supply port of the control valve or the
increase. common supply line of several associated valves, they control
They prevent shocks to any pneumatic system: each cylinder all designated cylinders (7870/7871/7874 type).
thus protected gradually returns to the position it stopped at specifications:
when the system was vented. suitable fluid: compressed air
Mounted on the F.R.L. outlet, they protect the whole working pressure: 40 to 150 psi
downsteam installation (7860/7861/7864 type). working temperature: 5˚ to 140˚ F
quick exhaust valve "safety"
The new Legris Quick Exhaust Valves can be used in all pneumatic equipment.
supply (1)
It drastically increases system efficiency and the speed of a cylinder by purging
cylinder exhaust air at the cylinder port rather than the control valve.

seal

piston supply (1) - the system pressure is specifications:

applied to the inlet port, flow is
working fluid: compressed air
directed to the cylinder port.
working pressure: 10 to 150 psi
exhaust (1)
supply (2) - the supply (1) is
dropped, exhaust air in the working temperature: 0º to 160º F
supply (2) cylinder is discharged directly materials of
from the exhaust (2) port of the construction
valve. body: nickel-plated brass
Immediate Installation seal: nylon
Easy To Use
piston: polyurethane
supply (2) Complete Safety

check valves "safety"

non-return non-return non-return

diaphragm diaphragm diaphragm

meter in version - green button meter out version - red button

(models 7984-7985) (models 7994-7995)

Legris in-line check valves allow air to pass in one direction specifications:
while blocking flow in the other direction. A pressure of more suitable fluid: compressed air
than 7 psi will overcome the spring pressure, which is keeping working pressure: 15 to 145 psi
the valve closed, thus allowing the passage of air. If the working temperature: 30˚ to 160˚ F
pressure differential is lower than 3.6 psi the passage is blocked.

pneumatic threshold sensors "safety"

to control valve diaphragm piston to control valve diaphragm piston

P' : exhaust pressure

P : system pressure
P1: supply pressure
for sensor
S : output signal

Legris threshold sensors detect pressure drops and are specifications:

generally used to detect the end-of travel of a cylinder. They suitable fluid: compressed air
produce an end-of-stroke signal, pneumatic or electric, when working temperature: 5˚ to 140˚ F
the exhaust back pressure in the cylinder disappears. working pressure: 45 to 115 psi
They can be mounted on the cylinder or on the control valve. breaking pressure: 7 to 8.5 psi
response time: 3 ms
flow control regulators
meter out version meter in version bi-directional version

fine adjustment screw fine adjustment screw fine adjustment screw

locknut locknut locknut

check valve check valve

A B C

Legris flow control regulators control the speed of a In this way, it is possible to avoid the elastic effect of the
pneumatic cylinder. In the one-way version, the exhaust or compressed air contained in the pipework between the
inlet air flow is controlled by an adjustable restrictor. control valve and cylinder.
The inlet or exhaust flow is unrestricted full bore. In a Direct mounting of the banjo flow regulator fitting onto
bi-directional version, they control air supply in both exhaust the cylinder is therefore the optimum solution.
and supply flow. Depending upon the model, Legris flow
regulators may be fitted on the cylinder or in the compressed specifications:
air line. However, flow regulation (and therefore cylinder suitable fluid: compressed air
control speed) is more precise and constant when positioned working pressure: 15 to 145 psi
near the cylinder. working temperature: 30˚ to 160˚ F

the large range of Legris flow control regulators answers

the specific needs of modern pneumatic applications
Which material?
Which type of adjustment?
models in
• for standard glass • for manual adjustment
applications reinforced with locking nut models with
nylon guaranteeing stability external screw
of adjustment

• for use in severe models in

conditions metal • for adjustment
with screwdriver knobless
and prevention models
of unwanted adjustment
• for use in severe models in
stainless steel
conditions
Which configuration?
Which type of fitting? • for standard
applications
90 degree
• for connection to the models models
cylinder or threaded with NPT, UNF, BSP
control valve parallel and metric,
BSP taper threads • for vertical or angled
tube exit
swivel outlet
• for connection to a models
cylinder or manifold
fitted with cartridge plug-in
connections
models • where cylinder access
is difficult or where
another function
Compact or miniature? valve is attached
to the cylinder port
in-line
models
• for standard compact
applications requiring models
full flow performance
Our production process includes manufactured dating
• for very small sized for all flow control regulators. This guarantees their
cylinders requiring quality and traceability.
precise and accurate miniature
adjustment models
lock-out valves
with instant fitting with threaded fitting
7885 NPT 7886 NPT
ØD(in) C C1 C2
1/4 1/8 7885 56 11 1/8 1/8 7886 11 11
1/4 1/4 7885 56 14 1/4 1/4 7886 14 14
3/8 3/8 7885 60 18 3/8 3/8 7886 18 18
1/2 1/2 7885 62 22 1/2 1/2 7886 22 22

7880 BSP parallel

ØD(mm) C 7881 BSP parallel
6 G1/8 7880 06 10 C1 C2
6 G1/4 7880 06 13 G1/4 G1/8 7881 13 10
8 G1/4 7880 08 13 G1/4 G1/4 7881 13 13
8 G3/8 7880 08 17 G3/8 G3/8 7881 17 17
10 G3/8 7880 10 17 G1/2 G1/2 7881 21 21
12 G1/2 7880 12 21

7885 BSP taper

ØD(mm) C 7886 BSP taper
6 R1/8 7885 06 10 C1 C2
6 R1/4 7885 06 13 R1/4 R1/8 7886 13 10
8 R1/4 7885 08 13 R1/4 R1/4 7886 13 13
8 R3/8 7885 08 17 R3/8 R3/8 7886 17 17
10 R3/8 7885 10 17 R1/2 R1/2 7886 21 21
12 R1/2 7885 12 21

Visual identification of different threads

7885 56 14 = NPT
7880 06 13 = BSP parallel
7885 06 13 = BSP taper

check valves
in-line with threaded fitting
7996 for inch tube
7984-7994-7985-7995 NPT and UNF
ØD(in) C Meter Out Meter In
ØD(in)
5/32 7996 04 00 5/32 10-32 7994 04 20 7984 04 20
1/4 7996 56 00 5/32 1/8 7995 04 11 7985 04 11
5/16 7996 08 00 1/4 1/8 7995 56 11 7985 56 11
3/8 7996 60 00 1/4 1/4 7995 56 14 7985 56 14
3/8 1/4 7995 60 14 7985 60 14
for metric tube 3/8 3/8 7995 60 18 7985 60 18
ØD(mm) 7984-7994 BSP parallel and metric
4 7996 04 00
ØD(mm) C Meter Out Meter In
6 7996 06 00
4 M5 7994 04 19 7984 04 19
8 7996 08 00
4 G1/8 7994 04 10 7984 04 10
10 7996 10 00
6 G1/8 7994 06 10 7984 06 10
12 7996 12 00
6 G1/4 7994 06 13 7984 06 13
8 G1/8 7994 08 10 7984 08 10
8 G1/4 7994 08 13 7984 08 13
4895 stainless steel - unidirectional, double-female
10 G3/8 7994 10 17 7984 10 17
NPT 12 G3/8 7994 12 17 7984 12 17
C 12 G1/2 7994 12 21 7984 12 21
1/8 4895 11 11
1/4 4895 14 14 7985-7995 BSP taper
3/8 4895 18 18
1/2 4895 22 22 ØD(mm) C Meter Out Meter In
4 R1/8 7995 04 10 7985 04 10
BSP version is also available
6 R1/8 7995 06 10 7985 06 10
6 R1/4 7995 06 13 7985 06 13
Visual identification of different threads 8 R1/8 7995 08 10 7985 08 10
8 R1/4 7995 08 13 7985 08 13
7995 04 11 = NPT/UNF 10 R3/8 7995 10 17 7985 10 17
7984 08 10 = BSP parallel 12 R3/8 7995 12 17 7985 12 17
7985 06 13 = BSP taper 12 R1/2 7995 12 21 7985 12 21
Meter in version - green button
Meter out version - red button
flow control regulators – nylon version A B C

miniature compact
7660-7665-7668-7669 UNF and NPT 7065-7066-7067 NPT
ØD C Meter Out (A) Meter In (B) ØD C Meter Out (A) Meter In (B) Bi-directional (C)
1/8 10-32 7660 53 20 7669 53 20 5/32 1/8 7065 04 11 7066 04 11 7067 04 11
1/8 1/8 7665 53 11 5/32 1/4 7065 04 14 7066 04 14
5/32 10-32 7660 04 20 7669 04 20 1/4 1/8 7065 56 11 7066 56 11 7067 56 11
5/32 1/8 7665 04 11 7668 04 11 1/4 1/4 7065 56 14 7066 56 14 7067 56 14
1/4 10-32 7660 56 20 7669 56 20 3/8 1/4 7065 60 14
1/4 1/8 7665 56 11 7668 56 11 3/8 3/8 7065 60 18
1/4 1/4 7665 56 14 7668 56 14
7060-7061-7062 BSP parallel
7660-7662-7669 BSP parallel and metric
ØD C Meter Out (A) Meter In (B) Bi-directional (C)
ØD C Meter Out (A) Meter In (B) Bi-directional ( C)
4 G1/8 7060 04 10 7061 04 10 7062 04 10
3 M3x0.5 7660 03 09 7669 03 09
6 G1/8 7060 06 10 7061 06 10 7062 06 10
3 M5x0.8 7660 03 19 7669 03 19
6 G1/4 7060 06 13 7061 06 13 7062 06 13
4 M5x0.8 7660 04 19 7669 04 19 7662 04 19
8 G1/8 7060 08 10 7061 08 10 7062 08 10
4 G1/8 7660 04 10 7669 04 10 7662 04 10
8 G1/4 7060 08 13 7061 08 13 7062 08 13
6 M5x0.8 7660 06 19 7669 06 19 7662 06 19
8 G3/8 7060 08 17 7061 08 17 7062 08 17
6 G1/8 7660 06 10 7669 06 10 7662 06 10
10 G1/4 7060 10 13 7061 10 13
6 G1/4 7660 06 13 7669 06 13 7662 06 13
10 G3/8 7060 10 17 7061 10 17
8 G1/8 7660 08 10 7669 08 10
12 G3/8 7060 12 17
8 G1/4 7660 08 13 7669 08 13
12 G1/2 7060 12 21 7061 12 21
8 G3/8 7660 08 17 7669 08 17

7665-7668 BSP taper 7065-7066-7067 BSP taper

ØD C Meter Out (A) Meter In (B) ØD C Meter Out (A) Meter In (B) Bi-directional (C)
4 R1/8 7665 04 10 7668 04 10 4 R1/8 7067 04 10
6 R1/8 7665 06 10 7668 06 10 6 R1/8 7065 06 10 7067 06 10
6 R1/4 7665 06 13 7668 06 13 6 R1/4 7067 06 13
6 R3/8 7665 06 17 8 R1/8 7065 08 10 7067 08 10
8 R1/8 7665 08 10 7668 08 10 8 R1/4 7065 08 13 7067 08 13
8 R1/4 7665 08 13 7668 08 13 8 R3/8 7067 08 17
8 R3/8 7665 08 17 7668 08 17 10 R1/4 7065 10 13 7066 10 13
10 R3/8 7065 10 17 7066 10 17
7620-7625 knobless, UNF and NPT 10 R1/2 7065 10 21 7066 10 21
ØD(in) C Meter Out (A) 12 R1/4 7065 12 13 7066 12 13
1/8 10-32 7620 53 20 12 R3/8 7065 12 17 7066 12 17
1/8 1/8 7625 53 11 12 R1/2 7065 12 21 7066 12 21
5/32 10-32 7620 04 20
7030-7031 plug-in, metric tube
5/32 1/8 7625 04 11 ØD Meter Out (A) Meter In (B)
1/4 10-32 7620 56 20
1/4 1/8 7625 56 11 6 7030 06 00 7031 06 00
1/4 1/4 7625 56 14 8 7030 08 00 7031 08 00
10 7030 10 00 7031 10 00
7630-7631 plug-in, for inch tube 12 7030 12 00 7031 12 00
ØD Meter Out (A) Meter In (B)
1/8 7630 53 00 7631 53 00
5/32 7630 04 00 7631 04 00
7045 swivel outlet, NPT
1/4 7630 56 00 7631 56 00 ØD C Meter Out (A)
plug-in, for metric tube 1/4 1/8 7045 56 11
ØD Meter Out (A) Meter In (B) 1/4 1/4 7045 56 14
4 7630 04 00 7631 04 00 3/8 1/4 7045 60 14
6 7630 06 00 7631 06 00 3/8 3/8 7045 60 18

7640-7645 swivel outlet, UNF and NPT

ØD C Meter Out (A)
5/32 10-32 7640 04 20 7040-7041 swivel outlet, BSP parallel
ØD C Meter Out (A) Meter In (B)
5/32 1/8 7645 04 11
6 G1/8 7040 06 10
6 G1/4 7040 06 13 7041 06 13
8 G1/8 7040 08 10 7041 08 10
8 G1/4 7040 08 13 7041 08 13
swivel outlet, 8 G3/8 7040 08 17
7640-7649 BSP parallel and metric 10 G1/4 7040 10 13
ØD C Meter Out (A) Meter in (B) 10 G3/8 7040 10 17
4 M5x0.8 7640 04 19 7649 04 19 12 G3/8 7040 12 17
4 G1/8 7640 04 10 7649 04 10 12 G1/2 7040 12 21
6 M5x0.8 7640 06 19 7649 06 19
6 G1/8 7640 06 10 7649 06 10 7045 swivel outlet, BSP taper
ØD C Meter Out (A)
6 R1/4 7045 06 13
8 R1/8 7045 08 10
7645 swivel outlet, BSP taper
8 R1/4 7045 08 13
ØD C Meter Out (A)
8 R3/8 7045 08 17
4 R1/8 7645 04 10 10 R1/4 7045 10 13
6 R1/8 7645 06 10 10 R3/8 7045 10 17
12 R3/8 7045 12 17
12 R1/2 7045 12 21
flow control regulators – nylon version A B C

knobless compact in-line

7010-7011-7015-7016 UNF and NPT 7770-7772 for inch tube
ØD C Meter Out (A) Meter In (B) ØD One-way Bi-directional
1/8 10-32 7010 53 20 5/32 7770 04 00 7772 04 00
1/8 1/8 7015 53 11 1/4 7770 56 00 7772 56 00
5/32 10-32 7010 04 20 7011 04 20 5/16 7770 08 00 7772 08 00
5/32 1/8 7015 04 11 7016 04 11 3/8 7770 60 00
1/4 10-32 7010 56 20 7011 56 20 1/2 7770 62 00
1/4 1/8 7015 56 11 7016 56 11
1/4 1/4 7015 56 14 7016 56 14 for metric tube
5/16 1/8 7015 08 11 ØD One-way Bi-directional
5/16 1/4 7015 08 14
4 7770 04 00 7772 04 00
3/8 1/4 7015 60 14
6 7770 06 00 7772 06 00
3/8 3/8 7015 60 18
8 7770 08 00 7772 08 00
10 7770 10 00
7010-7011-7012 BSP parallel and metric
12 7770 12 00
ØD C Meter Out (A) Meter In (B) Bi-directional (C)
4 M5x0.8 7010 04 19 7011 04 19 7012 04 19 7776 panel mountable, for metric tube
4 G1/8 7010 04 10 7011 04 10 7012 04 10 ØD One-way
6 M5x0.8 7010 06 19 7011 06 19 7012 06 19 4 7776 04 00
6 G1/8 7010 06 10 7011 06 10 7012 06 10 6 7776 06 00
6 G1/4 7010 06 13 7011 06 13 7012 06 13 8 7776 08 00
8 G1/8 7010 08 10 7011 08 10 7012 08 10 10 7776 10 00
8 G1/4 7010 08 13 7011 08 13 7012 08 13 12 7776 12 00
8 G3/8 7010 08 17 7011 08 17 7012 08 17
10 G1/4 7010 10 13 7011 10 13 7771-7775 with threaded fitting, NPT or BSP parallel
10 G3/8 7010 10 17 7011 10 17 C (NPT) One-way C (BSPP) One-way
10 G1/2 7010 10 21
1/8 7775 11 11 G1/8 7771 10 10
12 G3/8 7010 12 17
1/4 7775 14 14 G1/4 7771 13 13
12 G1/2 7010 12 21
3/8 7775 18 18 G3/8 7771 17 17
1/2 7775 22 22 G1/2 7771 21 21

flow control regulators – metal version A B

7105 push-to-connect port, NPT 7115 threaded port, NPT

ØD C Meter Out (A) C Meter Out (A)
5/32 1/8 7105 04 11 1/8 7115 11 11
1/4 1/8 7105 56 11 1/4 7115 14 14
1/4 1/4 7105 56 14 3/8 7115 18 18
3/8 1/4 7105 60 14 1/2 7115 22 22
3/8 3/8 7105 60 18

7100-7101 push-to-connect port, BSP parallel

ØD C Meter Out (A) Meter In (B) 7110-7111 threaded port, BSP parallel
4 G1/8 7100 04 10 7101 04 10 C Meter Out (A) Meter In (B)
6 G1/8 7100 06 10 7101 06 10 G1/8 7110 10 10 7111 10 10
6 G1/4 7100 06 13 7101 06 13 G1/4 7110 13 13 7111 13 13
8 G1/8 7100 08 10 7101 08 10 G3/8 7110 17 17
8 G1/4 7100 08 13 7101 08 13 G1/2 7110 21 21
8 G3/8 7100 08 17 7101 08 17
10 G1/4 7100 10 13
10 G3/8 7100 10 17
12 G3/8 7100 12 17
7160 knobless with universal brass compression fitting, BSP parallel
12 G1/2 7100 12 21 ØD C Meter Out (A)
14 G1/2 7100 14 21 4 G1/8 7160 04 10
6 G1/8 7160 06 10
6 G1/4 7160 06 13
8 G1/8 7160 08 10
8 G1/4 7160 08 13
10 G1/4 7160 10 13
10 G3/8 7160 10 17
10 G1/2 7160 10 21
12 G3/8 7160 12 17
12 G1/2 7160 12 21

Quick identification of Legris flow control regulators ● one-way adjustment

To assist differentiation, each version is identified by the corresponding - meter out version : letter A
pneumatic symbol and a letter :
- meter in version : letter B

● bi-directional adjustment : letter C

pneumatic threshold sensor fittings
with push-to-connect fitting with threaded fitting
7818-7808 UNF and NPT 7808 NPT
ØD C Pilot Port C
5/32 10-32 7818 04 20 10-32 1/8 7808 20 11
5/32 1/8 7808 04 11 10-32 1/4 7808 20 14
5/32 1/4 7808 04 14 10-32 3/8 7808 20 18
5/32 3/8 7808 04 18
5/32 1/2 7808 04 22

7818 BSP parallel and metric 7818 BSP parallel and metric
ØD C Pilot Port C
4 M5x0.8 7818 04 19 M5 M5x0.8 7818 19 19
4 G1/8 7818 04 10 M5 G1/8 7818 19 10
4 G1/4 7818 04 13 M5 G1/4 7818 19 13
4 G3/8 7818 04 17 M5 G3/8 7818 19 17
4 G1/2 7818 04 21 M5 G1/2 7818 19 21

7828/7829 electric, UNF and NPT

C Visual identification of different threads
10-32 7828 00 20 7808 04 11 = NPT/UNF
1/8 7829 00 11
7818 04 10 = BSP parallel
1/4 7829 00 14
3/8 7829 00 18
1/2 7829 00 22

7828 electric, BSP parallel and metric

C
M5x0.8 7828 00 19
G1/8 7828 00 10
G1/4 7828 00 13
G3/8 7828 00 17
G1/2 7828 00 21

flow control regulators - stainless steel

7810/7815/7812/7817 UNF and NPT 7835 NPT

C meter out bi-directional ØD C meter out

10/32 7810 20 20 7812 20 20 5/32 1/8 7835 04 11
1/8 7815 11 11 7817 11 11 5/32 1/4 7835 04 14
1/4 7815 14 14 7817 14 14 1/4 1/8 7835 56 11
3/8 7815 18 18 7817 18 18 1/4 1/4 7835 56 14
1/2 7815 22 22 7817 22 22 3/8 1/4 7835 60 14
3/8 3/8 7835 60 18

quick exhaust valve - nickel plated brass

7982 NPT

C
1/8 7982 11 11
1/4 7982 14 14
3/8 7982 18 18
1/2 7982 22 22
 pneumatic function valves

manual operated valves

2 2

1 3 3 1

manually operated 3-way venting valve pneumatic slide valves,

7805-7806 push-to-connect port, NPT 0661 male/female, NPT
ØD C Supply (1) Supply (2) ID (in) C
5/32 1/8 7805 04 11 7806 04 11 .16 1/8 0661 04 11
1/4 1/8 7805 56 11 7806 56 11 .27 1/4 0661 07 14
1/4 1/4 7805 56 14 7806 56 14 .39 3/8 0661 10 18
(1)
(2) 3/8 1/4 7805 60 14 7806 60 14 .55 1/2 0661 14 22

manually operated 3-way venting valve pneumatic slide valves,

7800-7801 push-to-connect port, BSP parallel 0660 double female, NPT
ØD C Supply (1) Supply (2) ID (in) C
4 M5x0.8 7800 04 19 7801 04 19 .16 1/8 0660 04 11
4 G1/8 7800 04 10 7801 04 10 .27 1/4 0660 07 14
6 M5x0.8 7800 06 19 7801 06 19 .39 3/8 0660 10 18
6 G1/8 7800 06 10 7801 06 10 .55 1/2 0660 14 22
6 G1/4 7800 06 13 7801 06 13
pneumatic slide valves,
(1) 8 G1/8 7800 08 10 7801 08 10 double female, BSP parallel
(2) 8 G1/4 7800 08 13 7801 08 13 0669
10 G1/4 7800 10 13 7801 10 13 ID (mm) C
2 M5x0.8 0669 02 19
4 G1/8 0669 04 10
Visual identification of different threads
7 G1/4 0669 07 13
7805 56 14 = NPT 10 G3/8 0669 10 17
7800 06 13 = BSP parallel 14 G1/2 0669 14 21
19 G3/4 0669 19 27

tubing

Pneumatic push-to-connect function valves with an LF3000 port, can be used

with various types of Legris tubing:
● semi-rigid close tolerance nylon tubing, available in 7 colors for 1/8” to
1/2” O.D. in 100 ft, 500 ft, & 1000 ft. rolls; 3 mm to 16 mm O.D., supplied in
25 m and 100 m rolls
● flexible close tolerance polyurethane tubing, available in 7 colors for
1/8” to 1/2“ O.D. in 100 ft, 500 ft, & 1000 ft. rolls; 3 mm to 14 mm O.D.,
supplied in 25 m and 100 m rolls
● low density polyethylene tubing :
available in 1/8” to 1/2” O.D. in 100 ft, 250 ft, & 500 ft. rolls and 4 mm to
12 mm O.D. in 25 m rolls
● close tolerance fluoropolymer FEP 140 tubing :

www.legris.com 1/8” to 1/2” O.D. in 25 ft. & 100 ft. rolls; 4 mm to 12 mm O.D., supplied in
5 m and 25 m rolls
pressure regulator fittings
7305 NPT 7300 BSP parallel
ØD C ØD C
5/32 1/8 7305 04 11 4 G1/8 7300 04 10
1/4 1/8 7305 56 11 6 G1/8 7300 06 10
1/4 1/4 7305 56 14 6 G1/4 7300 06 13
3/8 1/4 7305 60 14 8 G1/8 7300 08 10
8 G1/4 7300 08 13
8 G3/8 7300 08 17
10 G1/4 7300 10 13
10 G3/8 7300 10 17

pneumatic slow start valves

with instant fitting with threaded fitting
7860-7870 BSP parallel 7864-7874 NPT
ØD C System Version Component Version C System Version Component Version
8 G1/4 7860 08 13 7870 08 13 1/4 7864 14 14 7874 14 14
10 G1/4 7860 10 13 7870 10 13 3/8 7864 18 18 7874 18 18
10 G3/8 7860 10 17 7870 10 17
12 G3/8 7860 12 17
12 G1/2 7860 12 21

7861-7871 BSP parallel

Visual identification of different threads C System Version Component Version
7864 14 14 = NPT G1/4 7861 13 13 7871 13 13
G3/8 7861 17 17 7871 17 17
7860 10 17 = BSP parallel
G1/2 7861 21 21

mini ball valves 1 3

3/2, with vent, with push-to-connect ports 3/2, with vent, with male NPT and
7913 for inch tube 7915 push-to-connect ports
ØD (in) ØD (in) C
5/32 7913 04 00 5/32 1/8 7915 04 11
1/4 7913 56 00 1/4 1/8 7915 56 11
5/16 7913 08 00 1/4 1/4 7915 56 14
3/8 7913 60 00 5/16 1/4 7915 08 14
for metric tube 5/16 3/8 7915 08 18
3/8 1/4 7915 60 14
ØD (mm)
3/8 3/8 7915 60 18
4 7913 04 00
6 7913 06 00 BSP version is also available
8 7913 08 00
10 7913 10 00 2/2, with push-to-connect ports
12 7913 12 00 7910 for inch tube
ØD (in)
5/32 7910 04 00
1/4 7910 56 00
5/16 7910 08 00
3/8 7910 60 00
for metric tube
ØD (mm)
4 7910 04 00
6 7910 06 00
8 7910 08 00
Animation of function valves available on www.legris.com under...
10 7910 10 00
● Learning Space 12 7910 12 00
● Connection Techniques
Download CAD drawings from the online catalog.
symbols of pneumatic function valves
regulating exhausting system
air flow A B C and controlling pneumatic
circuit supply

controlling detecting
air circulation pressure drop

controlling regulating
and regulating air flow pressure by stabilizing
at a required value

controlling progressive
the passage of fluid in one direction pressurizing of circuits
and non-return in the other

reducing isolate a circuit

pressure supply without venting the whole
installation

You will find all these ranges

in our catalog and
on our web site at www.legris.com

UNITED STATES • MEXICO • CANADA

Legris Incorporated
7205 E. Hampton Avenue - Mesa, AZ 85209-3301
Tel: (480) 830-0216 - Fax: (800) 839-7556

www.legris.com
12P030708GB

a division of