YASKAWA

Varispeed G7
INSTRUCTION MANUAL
GENERAL PURPOSE INVERTER (ADVANCED VECTOR CONTROL)
MODEL: CIMR-G7B
200V CLASS 0.4 to 110kW (1.2 to 160kVA)
400V CLASS 0.4 to 300kW (1.4 to 460kVA)

Upon receipt of the product and prior to initial operation, read these instructions
thoroughly, and retain for future reference.

YASKAWA MANUAL NO. TOEP C710616 13B

Copyright © 2007 YASKAWA ELECTRIC CORPORATION

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system,
or transmitted, in any form, or by any means, mechanical, electronic, photocopying, recording,
or otherwise, without the prior written permission of Yaskawa. No patent liability is assumed
with respect to the use of the information contained herein. Moreover, because Yaskawa is con-
stantly striving to improve its high-quality products, the information contained in this manual is
subject to change without notice. Every precaution has been taken in the preparation of this
manual. Nevertheless, Yaskawa assumes no responsibility for errors or omissions. Neither is
any liability assumed for damages resulting from the use of the information contained in this
publication.
 Preface
This manual is designed to ensure correct and suitable
application of Varispeed G7-Series Inverters. Read
this manual before attempting to install, operate, main-
tain, or inspect an Inverter and keep it in a safe, conve-
nient location for future reference. Be sure you
understand all precautions and safety information
before attempting application.

General Precautions
• The diagrams in this manual may be indicated without covers or safety shields to show details.
Be sure to restore covers or shields before operating the Units and run the Units according to the
instructions described in this manual.
• Any illustrations, photographs, or examples used in this manual are provided as examples only
and may not apply to all products to which this manual is applicable.
• The products and specifications described in this manual or the content and presentation of the
manual may be changed without notice to improve the product and/or the manual.
• When ordering a new copy of the manual due to damage or loss, contact your Yaskawa represen-
tatives or the nearest Yaskawa sales office and provide the manual number shown on the front
cover.
• If nameplates become warn or damaged, order new ones from your Yaskawa representatives or
the nearest Yaskawa sales office.

i
 Safety Information
The following conventions are used to indicate precautions in this manual. Failure to heed pre-
cautions provided in this manual can result in serious or possibly even fatal injury or damage to
the products or to related equipment and systems.

Indicates precautions that, if not heeded, could possibly result in loss of life or serious injury.
WARNING

Indicates precautions that, if not heeded, could result in relatively serious or minor injury, damage
CAUTION to the product, or faulty operation.

Failure to heed a precaution classified as a caution can result in serious consequences depending
on the situation.

Indicates important information that should be memorized.

IMPORTANT

ii
Safety Precautions

„ Confirmations upon Delivery

CAUTION
• Never install an Inverter that is damaged or missing components.
Doing so can result in injury.

„ Installation

CAUTION
• Always hold the case when carrying the Inverter.
If the Inverter is held by the front cover, the main body of the Inverter may fall, possibly resulting in injury.
• Attach the Inverter to a metal or other noncombustible material.
Fire can result if the Inverter is attached to a combustible material.
• Install a cooling fan or other cooling device when installing more than one Inverter in the same
enclosure so that the temperature of the air entering the Inverters is below 45°C.
Overheating can result in fires or other accidents.

„ Wiring

WARNING
• Always turn OFF the input power supply before wiring terminals.
Otherwise, an electric shock or fire can occur.
• Wiring must be performed by an authorized person qualified in electrical work.
Otherwise, an electric shock or fire can occur.
• Be sure to ground the ground terminal. (200 V Class: Ground to 100 Ω or less, 400 V Class:
Ground to 10 Ω or less)
Otherwise, an electric shock or fire can occur.
• Always check the operation of any emergency stop circuits after they are wired.
Otherwise, there is the possibility of injury. (Wiring is the responsibility of the user.)
• Never touch the output terminals directly with your hands or allow the output lines to come into con-
tact with the Inverter case. Never short the output circuits.
Otherwise, an electric shock or ground short can occur.
• If the power supply is turned ON during the FWD (or REV) Run Command is given, the motor will
start automatically.
Turn the power supply ON after verifying that the RUN signal is OFF.
Failure to observe this warning may result in injury.
• When the 3-wire sequence is set, do not make the wiring for the control circuit unless the multi-
function input terminal constant is set.
Failure to observe this warning may result in injury.

CAUTION
• Check to be sure that the voltage of the main AC power supply satisfies the rated voltage of the
Inverter.
Injury or fire can occur if the voltage is not correct.
• Do not perform voltage withstand tests on the Inverter.
Otherwise, semiconductor elements and other devices can be damaged.
• Connect braking resistors, Braking Resistor Units, and Braking Units as shown in the I/O wiring
examples.
Otherwise, a fire can occur and the Inverter, braking resistors, Braking Resistor Units, and Braking Units can be damaged.

iii
 CAUTION
• Tighten all terminal screws to the specified tightening torque.
Otherwise, a fire may occur.
• Do not connect AC power to output terminals U, V, and W.
The interior parts of the Inverter will be damaged if voltage is applied to the output terminals.
• Do not connect phase-advancing capacitors or LC/RC noise filters to the output circuits.
The Inverter can be damaged or interior parts burnt if these devices are connected.
• Do not connect magnetic contactors to the output circuits.
If a load is connected while the Inverter is operating, surge current will cause the overcurrent protection circuit inside the
Inverter to operate.

„ Setting User Constants

CAUTION
• Disconnect the load (machine, device) from the motor before performing rotational autotuning.
The motor may turn, possibly resulting in injury or damage to equipment. Also, motor constants cannot be correctly set
with the motor attached to a load.
• Stay clear of the motor during rotational autotuning.
The motor repeats running and stopping until autotuning has been completed, possibly resulting in injury.
• In stationary autotuning 1, when the motor is first operated in the drive mode after tuning, the
remaining motor constants E2-02 (Motor rated slip) and E2-03 (Motor no-load current) are set auto-
matically. To perform an operation immediately after stationary autotuning 1, use the following pro-
cedure under the recommended conditions.
(1) Check the values of E2-02 and E2-03 in verify mode or advanced programming mode.
(2) Run the motor once in drive mode under the following conditions.
• The Inverter and the motor are connected.
• The motor shaft is not locked with a mechanical brake or other stopping mechanism (or function).
• A motor-load ratio of 30% or less is maintained.
• A speed of 30% or more of the base frequency set at E1-06 (default = highest frequency) is maintained at
a constant speed for one second or more.
(3) After stopping the motor, check the values of E2-02 and E2-03 again in verify mode or advanced program-
ming mode. If the values of E2-02 and E2-03 differ from the ones before the first operation was carried out,
the settings have been successfully completed. Next, check if the values are suitable or not.
If the values of E2-02 and E2-03 differed greatly from the reference data of the motor in the test report or the instruction
manual (TOE-S616-60.1), hunting, motor vibrations, insufficient motor torque, or an overcurrent may occur because the
motor is operated although the aforementioned conditions have not been fulfilled after stationary autotuning 1. For eleva-
tors, failure to observe this caution may result in the cage falling or injury. If so, perform stationary autotuning 1 again and
run the motor using the aforementioned procedure under the recommended conditions or perform stationary autotuning 2
or rotational autotuning.
Usually the standard setting for E2-02 is 1 Hz to 3 Hz, and that for E2-03 is 30% to 65% of the rated current for a general-
purpose motor. Generally, the larger the motor capacity is, the smaller the rated slip and the ratio of the no-load current to
the rated current become. Use the data given in Factory Settings that Change with the Inverter Capacity (o2-04) of Chap-
ter 5 User Constants as a reference.

„ Trial Operation

WARNING
• Check to be sure that the front cover is attached before turning ON the power supply.
An electric shock may occur.
• Do not come close to the machine when the fault reset function is used. If the alarmed is cleared,
the machine may start moving suddenly.
Also, design the machine so that human safety is ensured even when it is restarted.
Injury may occur.
• Provide a separate emergency stop switch; the Digital Operator STOP Key is valid only when its
function is set.
Injury may occur.

iv
 WARNING
• Reset alarms only after confirming that the RUN signal is OFF.
Injury may occur.

CAUTION
• Don't touch the radiation fins (heatsink), braking resistor, or Braking Resistor Unit. These can
become very hot.
Otherwise, a burn injury may occur.
• Be sure that the motor and machine is within the applicable ranges before starting operation.
Otherwise, an injury may occur.
• Provide a separate holding brake if necessary.
Always construct the external sequence to confirm that the holding brake is activated in the event
of an emergency, a power failure, or an abnormality in the Inverter.
Failure to observe this caution can result in injury.
• If using an Inverter with an elevator, take safety measures on the elevator to prevent the elevator
from dropping.
Failure to observe this caution can result in injury.
• Don't check signals while the Inverter is running.
Otherwise, the equipment may be damaged.
• Be careful when changing Inverter settings. The Inverter is factory set to suitable settings. For the
Inverters in the 400 V class of 55 kW or more, however, select the correct power supply voltage
jumper according to the input voltage.
Otherwise, the equipment may be damaged.

„ Maintenance and Inspection

WARNING
• Do not touch the Inverter terminals. Some of the terminals carry high voltages and are extremely
dangerous.
Doing so can result in electric shock.
• Always have the protective cover in place when power is being supplied to the Inverter. When
attaching the cover, always turn OFF power to the Inverter through the MCCB.
Doing so can result in electric shock.
• After turning OFF the main circuit power supply, wait until the CHARGE indicator light goes out
before performing maintenance or inspections.
The capacitor will remain charged and is dangerous.
• Maintenance, inspection, and replacement of parts must be performed only by authorized person-
nel.
Remove all metal objects, such as watches and rings, before starting work. Always use grounded tools.
Failure to heed these warning can result in electric shock.
• Provide a separate holding brake if necessary.
Always make any adjustments other than those involving the operation of the Inverter with the holding brake released.
Failure to observe this caution may result in injury.
• If using an Inverter with an elevator, take safety measures on the elevator to prevent the elevator
from dropping.
Failure to observe this caution can result in injury.

v
 CAUTION
• A CMOS IC is used in the control board. Handle the control board and CMOS IC carefully.
The CMOS IC can be destroyed by static electricity if touched directly.
• Do not change the wiring, or remove connectors or the Digital Operator, during operation.
Doing so can result in personal injury.

„ Other

WARNING
• Do not attempt to modify or alter the Inverter.
Doing so can result in electrical shock or injury.

CAUTION
• Do not subject the Inverter to halogen gases, such as fluorine, chlorine, bromine, and iodine, at any
time even during transportation or installation.
Otherwise, the Inverter can be damaged or interior parts burnt.

vi
Warning Information and Position
There is warning information on the Inverter in the position shown in the following illustration.
Always heed the warnings.

Warning
information
position
Warning
information
position

Illustration shows the CIMR-G7B20P4 Illustration shows the CIMR-G7B2018

Warning Information

! WARNING
Risk of electric shock.
yRead manual before installing.
yWait 5 minutes for capacitor discharge
after disconnecting power supply.

! AVERTISSEMENT

y
y

vii
 Warranty Information

„ Free Warranty Period and Scope

Warranty Period
This product is warranted for twelve months after being delivered to Yaskawa’s customer or if
applicable eighteen months from the date of shipment from Yaskawa’s factory whichever comes
first.

Scope of Warranty
Inspections
Periodic inspections must be conducted by the customer. However, upon request, Yaskawa or
one of Yaskawa’s Service Centers can inspect the product for a fee. In this case, if after confer-
ring with the customer, a Yaskawa product is found to be defective due to Yaskawa workman-
ship or materials and the defect occurs during the warranty period, then this fee will be waived
and the problem remedied free of charge.

Repairs
If a Yaskawa product is found to be defective due to Yaskawa workmanship or materials and the
defect occurs during the warranty period, Yaskawa will provide a replacement, repair the defec-
tive product, and provide shipping to and from the site free of charge.
However, if the Yaskawa Authorized Service Center determines that the problem with a
Yaskawa product is not due to defects in Yaskawa’s workmanship or materials, then the cus-
tomer will be responsible for the cost of any necessary repairs. Some problems that are outside
the scope of this warranty are:
• Problems due to improper maintenance or handling, carelessness, or other reasons where the
customer is determined to be responsible.
• Problems due to additions or modifications made to a Yaskawa product without Yaskawa’s
understanding.
• Problems due to the use of a Yaskawa product under conditions that do not meet the recom-
mended specifications.
• Problems caused by natural disaster or fire.
• Or other problems not due to defects in Yaskawa workmanship or materials.
Warranty service is only applicable within Japan.
However, after-sales service is available for customers outside of Japan for a reasonable fee.
Contact your local Yaskawa representative for more information.
„ Exceptions
Any inconvenience to the customer or damage to non-Yaskawa products due to Yaskawa's
defective products whether within or outside the warranty period are NOT covered by this war-
ranty.
„ Restrictions
• The Varispeed G7 was not designed or manufactured for use in devices or systems that may
directly affect or threaten human lives or health.
• Customers who intend to use the product described in this manual for devices or systems
relating to transportation, health care, space aviation, atomic or electric power, or underwater
use must contact their Yaskawa representatives or the nearest Yaskawa sales office before-
hand.
• This product has been manufactured under strict quality-control guidelines. However, if this
product is to be installed in any location where failure of this product could involve or result
in a life-and-death situation or loss of human life or in a facility where failure may cause a
serious accident or physical injury, safety devices must be installed to minimize the likelihood
of any accident.

viii
Registered Trademarks
The following registered trademarks are used in this manual.
• DeviceNet is a registered trademark of the ODVA (Open DeviceNet Vendors Association,
Inc.).
• InterBus is a registered trademark of Phoenix Contact Co.
• ControlNet is a registered trademark of ControlNet International, Ltd.
• LONWORKS is a registered trademark of the Echelon.

ix
 Contents
Safety Information ............................................................................................ii
Safety Precautions ..........................................................................................iii
Warning Information and Position ..................................................................vii
Warranty Information..................................................................................... viii
Registered Trademarks...................................................................................ix

1 Handling Inverters ...................................................................1-1

Varispeed G7 Introduction............................................................................ 1-2
‹ Varispeed G7 Models ..................................................................................................... 1-2
Confirmations upon Delivery ........................................................................ 1-3
‹ Checks ........................................................................................................................... 1-3
‹ Nameplate Information ................................................................................................... 1-3
‹ Component Names ........................................................................................................ 1-5
Exterior and Mounting Dimensions .............................................................. 1-6
‹ Open Chassis Inverters (IP00) ....................................................................................... 1-6
‹ Enclosed Wall-mounted Inverters [NEMA1 (Type 1)] ..................................................... 1-7
Checking and Controlling the Installation Site.............................................. 1-9
‹ Installation Site ............................................................................................................... 1-9
‹ Controlling the Ambient Temperature............................................................................. 1-9
‹ Protecting the Inverter from Foreign Matter ................................................................... 1-9
Installation Orientation and Space.............................................................. 1-10
Removing and Attaching the Terminal Cover ............................................. 1-11
‹ Removing the Terminal Cover ...................................................................................... 1-11
‹ Attaching the Terminal Cover ....................................................................................... 1-12
Removing/Attaching the Digital Operator and Front Cover ........................ 1-13
‹ Inverters of 15 kW or Less ........................................................................................... 1-13
‹ Inverters of 18.5 kW or More ........................................................................................ 1-16
Removing and Attaching the Protection Cover .......................................... 1-17
‹ Removing the Protection Cover ................................................................................... 1-17
‹ Attaching the Protection Cover..................................................................................... 1-18

2 Wiring .......................................................................................2-1
Connections to Peripheral Devices .............................................................. 2-2
Connection Diagram .................................................................................... 2-3
Terminal Block Configuration ....................................................................... 2-5
Wiring Main Circuit Terminals....................................................................... 2-6

x
 ‹ Applicable Wire Sizes and Closed-loop Connectors ......................................................2-6
‹ Main Circuit Terminal Functions ...................................................................................2-13
‹ Main Circuit Configurations........................................................................................... 2-14
‹ Standard Connection Diagrams.................................................................................... 2-15
‹ Wiring the Main Circuits................................................................................................ 2-16

Wiring Control Circuit Terminals .................................................................2-22

‹ Wire Sizes and Closed-loop Connectors ...................................................................... 2-22
‹ Control Circuit Terminal Functions ............................................................................... 2-24
‹ Control Circuit Terminal Connections ...........................................................................2-28
‹ Control Circuit Wiring Precautions................................................................................2-29

Wiring Check ..............................................................................................2-30

‹ Checks..........................................................................................................................2-30
Installing and Wiring Option Boards ...........................................................2-31
‹ Option Board Models and Specifications ...................................................................... 2-31
‹ Installation.....................................................................................................................2-32
‹ PG Speed Control Board Terminals and Specifications................................................ 2-33
‹ Wiring............................................................................................................................ 2-35
‹ Wiring Terminal Blocks .................................................................................................2-38
‹ Selecting the Number of PG (Encoder) Pulses ............................................................ 2-39

3 Digital Operator and Modes................................................... 3-1

Digital Operator ............................................................................................3-2
‹ Digital Operator Display.................................................................................................. 3-2
‹ Digital Operator Keys......................................................................................................3-2
Modes...........................................................................................................3-5
‹ Inverter Modes................................................................................................................ 3-5
‹ Switching Modes............................................................................................................. 3-6
‹ Drive Mode .....................................................................................................................3-7
‹ Quick Programming Mode ..............................................................................................3-8
‹ Advanced Programming Mode ..................................................................................... 3-10
‹ Verify Mode................................................................................................................... 3-13
‹ Autotuning Mode........................................................................................................... 3-14

4 Trial Operation ........................................................................ 4-1

Overview of Trial Operation Procedure ........................................................4-2
Trial Operation Procedures...........................................................................4-3
‹ Setting the Power Supply Voltage Jumper
(400 V Class Inverters of 55 kW or Higher) ....................................................................4-3
‹ Power ON .......................................................................................................................4-3
‹ Checking the Display Status...........................................................................................4-4
‹ Basic Settings .................................................................................................................4-5
‹ Settings for the Control Methods .................................................................................... 4-7
‹ Autotuning.......................................................................................................................4-9
‹ Application Settings ...................................................................................................... 4-16
‹ No-load Operation ........................................................................................................ 4-16

xi
 ‹ Loaded Operation......................................................................................................... 4-16
‹ Check and Recording User Constants ......................................................................... 4-17
Adjustment Suggestions ............................................................................ 4-18

5 User Constants ........................................................................5-1

User Constant Descriptions.......................................................................... 5-2
‹ Description of User Constant Tables .............................................................................. 5-2
Digital Operation Display Functions and Levels........................................... 5-3
‹ User Constants Settable in Quick Programming Mode .................................................. 5-4
User Constant Tables ................................................................................... 5-8
‹ A: Setup Settings............................................................................................................ 5-8
‹ b: Application Constants............................................................................................... 5-10
‹ C: Autotuning Constants .............................................................................................. 5-21
‹ d: Reference Constants................................................................................................ 5-27
‹ E: Motor Constant Constants ....................................................................................... 5-33
‹ F: Option Constants ..................................................................................................... 5-38
‹ H: Terminal Function Constants................................................................................... 5-45
‹ L: Protection Function Constants ................................................................................. 5-57
‹ N: Special Adjustments ................................................................................................ 5-68
‹ o: Digital Operator Constants ....................................................................................... 5-72
‹ T: Motor Autotuning...................................................................................................... 5-76
‹ U: Monitor Constants.................................................................................................... 5-77
‹ Factory Settings that Change with the Control Method (A1-02) ................................... 5-86
‹ Factory Settings that Change with the Inverter Capacity (o2-04)................................. 5-89

6 Constant Settings by Function...............................................6-1

Frequency Reference................................................................................... 6-2
‹ Selecting the Frequency Reference Source................................................................... 6-2
‹ Using Multi-Step Speed Operation................................................................................. 6-5
‹ Varispeed G7 Function Block......................................................................................... 6-8
Run Command ........................................................................................... 6-10
‹ Selecting the Run Command Source ........................................................................... 6-10
Stopping Methods ...................................................................................... 6-12
‹ Selecting the Stopping Method when a Stop Command is Sent .................................. 6-12
‹ Using the DC Injection Brake ....................................................................................... 6-16
‹ Using an Emergency Stop............................................................................................ 6-17
Acceleration and Deceleration Characteristics .......................................... 6-18
‹ Setting Acceleration and Deceleration Times............................................................... 6-18
‹ Accelerating and Decelerating Heavy Loads (Dwell Function) .................................... 6-22
‹ Preventing the Motor from Stalling During Acceleration (Stall Prevention During
Acceleration Function).................................................................................................. 6-23
‹ Preventing Overvoltage During Deceleration (Stall Prevention During Deceleration
Function) ...................................................................................................................... 6-25
‹ Preventing Overvoltage by Automatically Reducing the Regenerative Torque Limit
(Overvoltage Inhibit Function) ...................................................................................... 6-26

xii
Adjusting Frequency References ...............................................................6-28
‹ Adjusting Analog Frequency References .....................................................................6-28
‹ Operation Avoiding Resonance (Jump Frequency Function) .......................................6-31
‹ Adjusting Frequency Reference Using Pulse Train Inputs ........................................... 6-33
Speed Limit (Frequency Reference Limit Function) ...................................6-34
‹ Limiting Maximum Output Frequency ...........................................................................6-34
‹ Limiting Minimum Frequency........................................................................................ 6-34
Improved Operating Efficiency ...................................................................6-36
‹ Reducing Motor Speed Fluctuation (Slip Compensation Function) ..............................6-36
‹ Compensating for Insufficient Torque at Startup and Low-speed Operation
(Torque Compensation) ................................................................................................ 6-38
‹ Hunting-prevention Function.........................................................................................6-40
‹ Stabilizing Speed (Speed Feedback Detection Function) ............................................6-41
Machine Protection.....................................................................................6-42
‹ Reducing Noise and Leakage Current.......................................................................... 6-42
‹ Limiting Motor Torque (Torque Limit Function).............................................................6-46
‹ Preventing Motor Stalling During Operation ................................................................. 6-49
‹ Changing Stall Prevention Level during Operation Using an Analog Input .................. 6-50
‹ Using Frequency Detection: L4-01 to L4-05 ................................................................. 6-50
‹ Detecting Motor Torque ................................................................................................ 6-53
‹ Changing Overtorque and Undertorque Detection Levels Using an Analog Input ....... 6-56
‹ Motor Overload Protection............................................................................................6-57
‹ Setting Motor Protection Operation Time...................................................................... 6-59
‹ Motor Overheating Protection Using PTC Thermistor Inputs........................................ 6-60
‹ Limiting Motor Rotation Direction.................................................................................. 6-62

Continuing Operation..................................................................................6-63
‹ Restarting Automatically After Power Is Restored ........................................................ 6-63
‹ Speed Search ...............................................................................................................6-64
‹ Continuing Operation at Constant Speed When Frequency Reference Is Lost............ 6-71
‹ Restarting Operation After Transient Fault (Auto Restart Function)............................. 6-72
‹ Operation Selection After Cooling Fan Fault ................................................................6-73

Inverter Protection ......................................................................................6-74

‹ Performing Overheating Protection on Mounted Braking Resistors ............................. 6-74
‹ Reducing Inverter Overheating Pre-Alarm Warning Levels.......................................... 6-75
Input Terminal Functions ............................................................................6-76
‹ Temporarily Switching Operation between Digital Operator and Control Circuit
Terminals ......................................................................................................................6-76
‹ Blocking Inverter Outputs (Baseblock Commands) ...................................................... 6-77
‹ Stopping Acceleration and Deceleration (Acceleration/Deceleration Ramp Hold) ....... 6-78
‹ Raising and Lowering Frequency References Using Contact Signals (UP/DOWN).....6-79
‹ Accelerating and Decelerating Constant Frequencies in the Analog References
(+/- Speed)....................................................................................................................6-82
‹ Hold Analog Frequency Using User-set Timing............................................................ 6-83
‹ Switching Operations between a Communications Option Board and Control
Circuit Terminals ........................................................................................................... 6-83

xiii
 ‹ Jog Frequency Operation without Forward and Reverse Commands
(FJOG/RJOG) .............................................................................................................. 6-84
‹ Stopping the Inverter by Notifying Programming Device Errors to the Inverter
(External Fault Function) .............................................................................................. 6-85

Output Terminal Functions ......................................................................... 6-86

Monitor Constants ...................................................................................... 6-88
‹ Using the Analog Monitor Constants ............................................................................ 6-88
‹ Using Pulse Train Monitor Contents ............................................................................. 6-90
Individual Functions ................................................................................... 6-92
‹ Using MEMOBUS Communications ............................................................................. 6-92
‹ Using the Timer Function ........................................................................................... 6-105
‹ Using PID Control....................................................................................................... 6-106
‹ Energy-saving ............................................................................................................ 6-115
‹ Setting Motor Constants............................................................................................. 6-117
‹ Setting the V/f Pattern ................................................................................................ 6-120
‹ Torque Control ........................................................................................................... 6-127
‹ Speed Control (ASR) Structure .................................................................................. 6-136
‹ Increasing the Speed Reference Response (Feed Forward Control) ........................ 6-142
‹ Droop Control Function .............................................................................................. 6-143
‹ Zero-servo Function ................................................................................................... 6-145

Digital Operator Functions........................................................................ 6-148

‹ Setting Digital Operator Functions ............................................................................. 6-148
‹ Copying Constants ..................................................................................................... 6-151
‹ Prohibiting Writing Constants from the Digital Operator ............................................. 6-156
‹ Setting a Password .................................................................................................... 6-156
‹ Displaying User-set Constants Only........................................................................... 6-157

Options..................................................................................................... 6-158
‹ Performing Speed Control with PG ............................................................................ 6-158
‹ Using Digital Output Boards ....................................................................................... 6-162
‹ Using an Analog Reference Board............................................................................. 6-164
‹ Using a Digital Reference Board ................................................................................ 6-165

Using Inverters for Elevating Machines.................................................... 6-170

‹ Brake ON/OFF Sequence .......................................................................................... 6-170
‹ Stall Prevention during Deceleration .......................................................................... 6-172
‹ Autotuning .................................................................................................................. 6-172
‹ Braking Resistor Overheating Protection ................................................................... 6-172
‹ Momentary Power Loss Restart ................................................................................. 6-172
‹ Torque Limit................................................................................................................ 6-172
‹ I/O Open-phase Protection and Overtorque Detection .............................................. 6-173
‹ External Baseblock Signal.......................................................................................... 6-173
‹ Acceleration/Deceleration Time.................................................................................. 6-173
‹ Magnetic Contactor on the Inverter’s Output-side...................................................... 6-173
‹ Control-related Adjustments ....................................................................................... 6-174
‹ Reducing Shock during Elevating Machine Start, Stop, Acceleration, and
Deceleration ............................................................................................................... 6-176

xiv
 ‹ Confirming Startup Current and Reducing Carrier Frequency....................................6-179
‹ Overvoltage Inhibit Function .......................................................................................6-180
Current Alarm Function ............................................................................6-181
Peak Hold Current Monitoring Function ...................................................6-182
Maintenance Timer Display Function .......................................................6-183
‹ Settings Required to Use Maintenance Timer Display Function................................. 6-183
‹ Settings Required After Replacement of Cooling Fan or Electrolytic Capacitor ......... 6-184

7 Troubleshooting ..................................................................... 7-1

Protective and Diagnostic Functions ............................................................7-2
‹ Fault Detection................................................................................................................ 7-2
‹ Alarm Detection ............................................................................................................7-15
‹ Operation Errors ........................................................................................................... 7-19
‹ Errors During Autotuning ............................................................................................. 7-21
‹ Errors when Using the Digital Operator Copy Function................................................ 7-22

Troubleshooting ..........................................................................................7-24
‹ If Constant Constants Cannot Be Set ...........................................................................7-24
‹ If the Motor Does Not Operate......................................................................................7-25
‹ If the Direction of the Motor Rotation is Reversed ........................................................ 7-28
‹ If the Motor Does Not Put Out Torque or If Acceleration is Slow .................................. 7-28
‹ If the Motor Operates Higher Than the Reference .......................................................7-28
‹ If the Slip Compensation Function Has Low Speed Precision......................................7-29
‹ If There is Low Speed Control Accuracy at High-speed Rotation in Open-loop
Vector Control Method .................................................................................................. 7-29
‹ If Motor Deceleration is Slow ........................................................................................ 7-29
‹ If the Motor Overheats .................................................................................................. 7-30
‹ If There is Noise When the Inverter is Started or From an AM Radio .......................... 7-31
‹ If the Ground Fault Interrupter Operates When the Inverter is Run..............................7-31
‹ If There is Mechanical Oscillation .................................................................................7-31
‹ If the Torque Generated for the Motor is Insufficient (Insufficient Power) ..................... 7-33
‹ If the Torque Reference (U1-09) at Low Speeds in Open-loop Vector 2 Control is
Large Compared to That at Medium and High Speeds ................................................ 7-33
‹ If Shock Occurs Near the Speed Estimator Switching Frequency in Open-loop
Vector 2 Control ............................................................................................................7-33
‹ If Torque Ripple Occurs at Very Low Speeds in Open-loop Vector 2 Control ............... 7-34
‹ If the Motor Rotates Even When Inverter Output is Stopped........................................ 7-34
‹ If OV is Detected When the Fan is Started, or Fan Stalls ............................................. 7-34
‹ If Output Frequency Does Not Rise to Frequency Reference ......................................7-34
‹ Acoustic Noise From the Motor .................................................................................... 7-35

8 Maintenance and Inspection.................................................. 8-1

Maintenance and Inspection.........................................................................8-2
‹ Outline of Warranty .........................................................................................................8-2
‹ Daily Inspection ..............................................................................................................8-2

xv
 ‹ Periodic Inspection ......................................................................................................... 8-2
‹ Periodic Maintenance of Parts ....................................................................................... 8-3
‹ Procedure for Adjusting Constants after Replacement of Control Board ....................... 8-3
‹ Types and Number of Cooling Fans Used in the Drive .................................................. 8-5
‹ Cooling Fan Replacement Outline ................................................................................. 8-6
‹ Circulation Fan Replacement Outline........................................................................... 8-16
‹ Removing and Mounting the Control Circuit Terminal Board ....................................... 8-21

9 Specifications ..........................................................................9-1
Standard Inverter Specifications................................................................... 9-2
‹ Specifications by Model.................................................................................................. 9-2
‹ Common Specifications.................................................................................................. 9-4
Specifications of Options and Peripheral Devices........................................ 9-6

10 Appendix ................................................................................10-1
Varispeed G7 Control Methods .................................................................. 10-2
‹ Control Methods and Features..................................................................................... 10-2
‹ Control Methods and Applications................................................................................ 10-4
Inverter Application Precautions ................................................................ 10-6
‹ Selection....................................................................................................................... 10-6
‹ Installation .................................................................................................................... 10-7
‹ Settings ........................................................................................................................ 10-7
‹ Handling ....................................................................................................................... 10-8

Motor Application Precautions ................................................................... 10-9

‹ Using the Inverter for an Existing Standard Motor........................................................ 10-9
‹ Using the Inverter for Special Motors ......................................................................... 10-10
‹ Power Transmission Mechanism (Speed Reducers, Belts, and Chains) ................... 10-10
Conformance to UL Standard................................................................... 10-11
Conformance to CE Markings .................................................................. 10-13
‹ CE Markings............................................................................................................... 10-13
‹ Requirements for Conformance to CE Markings........................................................ 10-13
Wiring Examples ...................................................................................... 10-20
‹ Using a Braking Resistor Unit .................................................................................... 10-20
‹ Using a Braking Unit and Braking Resistor Unit ......................................................... 10-21
‹ Using Braking Units in Parallel ................................................................................... 10-22
‹ Using a Braking Unit and Three Braking Resistor Units in Parallel ............................ 10-23
‹ Using a VS Operator .................................................................................................. 10-24
‹ Using Transistors for Input Signals and a 0-V Common in Sinking Mode with an
Internal Power Supply ................................................................................................ 10-25
‹ Using Transistors for Input Signals and a +24-V Common in Sourcing Mode ........... 10-26
‹ Using Transistors for Input Signals and a 0-V Common in Sinking Mode with an
External Power Supply ............................................................................................... 10-27
‹ Using Contact and Open Collector Outputs ............................................................... 10-28

xvi
 User Constants .........................................................................................10-29

INDEX

Revision History

xvii
Handling Inverters
This chapter describes the checks required upon receiving or installing an Inverter.

Varispeed G7 Introduction ...........................................1-2

Confirmations upon Delivery........................................1-3
Exterior and Mounting Dimensions..............................1-6
Checking and Controlling the Installation Site .............1-9
Installation Orientation and Space .............................1-10
Removing and Attaching the Terminal Cover ............ 1-11
Removing/Attaching the Digital Operator and Front
Cover .........................................................................1-13
Removing and Attaching the Protection Cover..........1-17
 Varispeed G7 Introduction

‹ Varispeed G7 Models
The Varispeed-G7 Series of Inverters included two Inverters in two voltage classes: 200 V and 400 V. Maximum
motor capacities vary from 0.4 to 300 kW (41 models).

Table 1.1 Varispeed G7 Models

Specifications
Maximum Varispeed G7
(Always specify through the protective structure when ordering.)
Voltage Motor
Class Capacity Output Open Chassis Enclosed Wall-mounted
Capacity Basic Model Number (IEC IP00) [IEC IP20, NEMA 1 (Type 1)]
kW
kVA CIMR-G7B††††† CIMR-G7B††††††
0.4 1.2 CIMR-G7B20P4 20P41†
0.75 2.3 CIMR-G7B20P7 20P71†
1.5 3.0 CIMR-G7B21P5 21P51†
2.2 4.6 CIMR-G7B22P2 Remove the top and bottom cov- 22P21†
3.7 6.9 CIMR-G7B23P7 ers from the Enclosed Wall- 23P71†
5.5 10 CIMR-G7B25P5 mounted model. 25P51†
7.5 13 CIMR-G7B27P5 27P51†
11 19 CIMR-G7B2011 2011†
15 25 CIMR-G7B2015 20151†
200 V Class
18.5 30 CIMR-G7B2018 20180† 20181†
22 37 CIMR-G7B2022 20220† 20221†
30 50 CIMR-G7B2030 20300† 20301†
37 61 CIMR-G7B2037 20370† 20371†
45 70 CIMR-G7B2045 20450† 20451†
55 85 CIMR-G7B2055 20550† 20551†
75 110 CIMR-G7B2075 20750† 20751†
90 140 CIMR-G7B2090 20900† -
110 160 CIMR-G7B2110 21100† -
0.4 1.4 CIMR-G7B40P4 40P41†
0.75 2.6 CIMR-G7B40P7 40P71†
1.5 3.7 CIMR-G7B41P5 41P51†
2.2 4.7 CIMR-G7B42P2 Remove the top and bottom cov- 42P21†
3.7 6.9 CIMR-G7B43P7 ers from the Enclosed Wall- 43P71†
5.5 11 CIMR-G7B45P5 mount model. 45P51†
7.5 16 CIMR-G7B47P5 47P51†
11 21 CIMR-G7B4011 40111†
15 26 CIMR-G7B4015 40151†
18.5 32 CIMR-G7B4018 40180† 40181†
22 40 CIMR-G7B4022 40220† 40221†
400 V Class 30 50 CIMR-G7B4030 40300† 40301†
37 61 CIMR-G7B4037 40370† 40371†
45 74 CIMR-G7B4045 40450† 40451†
55 98 CIMR-G7B4055 40550† 40551†
75 130 CIMR-G7B4075 40750† 40751†
90 150 CIMR-G7B4090 40900† 40901†
110 180 CIMR-G7B4110 41100† 41101†
132 210 CIMR-G7B4132 41320† 41321†
160 250 CIMR-G7B4160 41600† 41601†
185 280 CIMR-G7B4185 41850† -
220 340 CIMR-G7B4220 42200† -
300 460 CIMR-G7B4300 43000† -

1-2
 Confirmations upon Delivery

Confirmations upon Delivery

‹ Checks
Check the following items as soon as the Inverter is delivered.

Table 1.2 Checks

Item Method
Has the correct model of Inverter been
Check the model number on the nameplate on the side of the Inverter.
delivered?
Inspect the entire exterior of the Inverter to see if there are any scratches or
Is the Inverter damaged in any way?
other damage resulting from shipping.
Are any screws or other components
Use a screwdriver or other tools to check for tightness.
loose?

If you find any irregularities in the above items, contact the agency from which you purchased the Inverter or
your Yaskawa representative immediately.

‹ Nameplate Information
There is a nameplate attached to the side of each Inverter. The nameplate shows the model number, specifica-
tions, lot number, serial number, and other information on the Inverter.

„ Example Nameplate
The following nameplate is an example for a standard domestic (Japan) Inverter: 3-phase, 200 VAC, 0.4 kW,
IEC IP20 and NEMA 1 (Type 1) standards

Inverter model G B A Inverter

specifications
Input specifications

Output
specifications
Lot number O/N : Mass

Serial number S/N : 3030 Version of software

UL file number UL FILE NO.: E131457

Fig 1.1 Nameplate

1-3
 „Inverter Model Numbers
The model number of the Inverter on the nameplate indicates the specification, voltage class, and maximum
motor capacity of the Inverter in alphanumeric codes.

CIMR - G7 B 2 0P4
Inverter
Varispeed G7
No. Specification No. Max. Motor Capacity
B China domestic model 0P4 0.4 kW
0P7 0.75 kW
to to
300 *
No. Voltage Class 300 kW
2 AC input, 3-phase, 200 V "P" indicates the decimal point.
4 AC input, 3-phase, 400 V

Fig 1.2 Inverter Model Numbers

„Inverter Specifications
The Inverter specifications (“SPEC”) on the nameplate indicate the voltage class, maximum motor capacity,
the protective structure, and the revision of the Inverter in alphanumeric codes.

2 0P4 1 A
No. Voltage Class
2 AC input, 3-phase, 200 V Design revision order
4 AC input, 3-phase, 400 V

No. Max. Motor Capacity No. Protective Structure

0P4 0.4 kW 0 Open chassis (IEC IP00)
0P7 0.75 kW 1 Enclosed wall-mounted [IEC IP20,
to to NEMA 1 (Type 1)]
300 300 kW *
"P" indicates the decimal point.

Fig 1.3 Inverter Specifications

Open Chassis Type (IEC IP00)

Protected so that parts of the human body cannot reach electrically charged parts from the front when the
Inverter is mounted in a control panel.
TERMS Enclosed Wall-mounted Type [IEC IP20, NEMA 1 (Type 1)]
The Inverter is structured so that the Inverter is shielded from the exterior, and can thus be mounted to the
interior wall of a standard building (not necessarily enclosed in a control panel). The protective structure con-
forms to the standards of NEMA 1 (Type 1) in the USA. The protective covers (see Fig. 1.4) are required for
an IEC IP20 or NEMA 1 (Type 1) protective structure.

1-4
 Confirmations upon Delivery

‹ Component Names
The external appearance and component names of the Inverter are shown in Fig 1.4. The Inverter with the ter-
minal cover removed is shown in Fig 1.5.

Top protective cover

Mounting
hole
Inverter cover
Cooling
fan
Front Mounting hole Front cover
cover

Digital Diecast case Digital

Operator
Operator

Terminal
Nameplate Terminal
cover Nameplate
cover

Bottom protective cover

15 kW or Less 18.5 kW or More

Fig 1.4 Inverter Appearance

Charge indicator

Control circuit
terminals

Main circuit
terminals

Charge indicator

Ground terminal

15 kW or Less 18.5 kW or More

Fig 1.5 Terminal Arrangement

1-5
 Exterior and Mounting Dimensions

‹ Open Chassis Inverters (IP00)

Exterior diagrams of the Open Chassis Inverters are shown below.

W1 W1 4-d
4-d

H1

H
H1

t1

H2
D1
t1 (5)* W (5)* (5) D

* (10) for 200 V Class Inverters of 30 to 110 kW or

H2

W D1
400 V Class Inverters of 55 to 160 kW.
3 D

200 V/400 V Class Inverters of 0.4 to 15 kW 200 V Class Inverters of 18.5 to 110 kW
400 V Class Inverters of 18.5 to 160 kW

6-d
W1
W2
H1
H
H2

W3 t1
W1 D1
W D

400 V Class Inverters of 185 to 300 kW

Fig 1.6 Exterior Diagrams of Open Chassis Inverters

1-6
 Exterior and Mounting Dimensions

‹ Enclosed Wall-mounted Inverters [NEMA1 (Type 1)]

Exterior diagrams of the Enclosed Wall-mounted Inverters [NEMA1 (Type 1)] are shown below.

W1 4-d W1 4-d

H1
H0
H
H1

H0

H2
t1

H3
Max.10
t1 D1
H2

H3

W D1 (5)* W (5)* (5) D

Grommet
3 D
* (7.5) for 200 V Class Inverters of 30 to 75 kW or 400 V
200 V/400 V Class Inverters of 0.4 to 15 kW Class Inverters of 55 to 160 kW.
200 V Class Inverters of 18.5 to 75 kW
400 V Class Inverters of 18.5 to 160 kW

Fig 1.7 Exterior Diagrams of Enclosed Wall-mounted Inverters

1-7
 Table 1.3 200 VAC and 400 VAC (0.4 kW to 300 kW) Inverter Dimensions (mm) and Masses (kg)
Max. Heat Genera-
Dimensions (mm)
Appli- tion (W)
Voltage cable Open Chassis (IP00) Enclosed Wall-mounted [NEMA1 (Type 1)] Total Cooling
Class Motor Heat Method
Mount- Exter Inter-
Gen-
Output W H D W1 H1 H2 D1 t1 Approx.
W H D W1 H0 H1 H2 H3 D1 t1 Approx. ing nal nal
era-
Mass Mass Holes
[kW] d* tion
0.4 21 36 57
Natu-
0.75 157 39 3 157 39 3 43 42 85
ral
1.5 140 280 126 266 7 5 140 280 126 280 266 7 5 M5 58 47 105
2.2 83 53 136
177 59 4 177 0 59 4
3.7 122 64 186
5.5 6 6 187 87 274
200 300 197 186 285 8 65.5 200 300 197 186 300 285 8 65.5
7.5 7 7 263 112 375
11 350 357 136 493
240 350 207 216 335 78 2.3 11 240 207 216 350 335 78 2.3 11 M6
200 V 15 380 30 473 174 647
7.5 7.5
(3-phase) 18.5 250 400 195 385 21 254 535 195 400 385 135 24 599 242 839
258 100 258
22 275 450 220 435 24 279 615 220 450 435 165 100 27 679 257 936 Fan
30 298 100 57 298 62 878 362 1240
375 600 250 575 380 809 250 600 575 209
37 328 63 328 68 1080 434 1514
12.5 3.2 12.5 3.2 M10
45 86 94 1291 510 1801
450 725 348 325 700 130 453 1027 348 325 725 700 302 130
55 87 95 1474 607 2081
75 500 850 358 370 820 108 504 1243 358 370 850 820 15 393 4.5 114 2009 823 2832
90 15 4.5 M12 1660 871 2531
575 885 378 445 855 140 150 ---
110 2389 1194 3583
0.4 10 39 49 Natu-
157 39 3.5 157 39 3.5
0.75 21 44 65 ral
1.5 140 280 126 266 7 5 140 280 126 280 266 7 5 M5 33 46 79
2.2 177 59 4.5 177 59 4.5 41 49 90
3.7 0 76 64 140
5.5 132 79 211
200 300 197 186 285 8 65.5 7 200 300 197 186 300 285 8 65.5 7
7.5 198 106 304
11 246 116 362
240 350 207 216 335 78 10 240 350 207 216 350 335 78 10
15 311 135 446
18.5 2.3 2.3 M6 354 174 528
275 450 258 220 435 100 26 279 535 258 220 450 435 100 29
22 7.5 7.5 516 210 726
400 V 85 Fan
30 633 246 879
(3-phase) 635 39
37 325 550 283 260 535 105 37 329 283 260 550 535 105 737 285 1022
45 715 165 40 929 340 1269
55 90 98 1239 488 1727
450 725 348 325 700 12.5 3.2 453 1027 348 325 725 700 12.5 302 3.2 M10
75 91 99 1554 596 2150
130 130
90 109 127 1928 762 2690
500 850 358 370 820 15 504 1243 358 370 850 820 15 393
110 127 137 2299 928 3227
4.5 4.5 M12
132 165 175 2612 1105 3717
575 916 378 445 855 46 140 579 1324 378 445 916 855 46 408 140
160 175 185 3614 1501 5115
185
220 See Table 1.4
300

* Same for Open Chassis and Enclosed Wall-mounted Inverters.

Table 1.4 400 VAC (185 to 300 kW) Inverter Dimensions (mm) and Masses (kg)
Max. Dimensions (mm) Heat Generation (W)
Appli- Open Chassis (IP00) Enclosed Wall-mounted [NEMA (Type1)]
Voltage cable Total Cooling
Mount- Exter- Inter- Heat
Class Motor Approx. Approx. ing
Method
W H D W1 W2 W3 H1 H2 D1 t1 W H D W1 W2 W3 H1 H2 D1 t1 nal nal Gener-
Output Mass Mass Holes ation
[kW] d*

185 260 4436 1994 6430

710 1305 413 540 240 270 1270 15 125.5 4.5
400 V
220 280 --- M12 5329 2205 7534 Fan
(3-phase)

300 916 1475 413 730 365 365 1440 15 125.5 4.5 415 6749 2941 9690

1-8
 Checking and Controlling the Installation Site

Checking and Controlling the Installation Site

Install the Inverter in the installation site described below and maintain optimum conditions.

‹ Installation Site
Install the Inverter under the following conditions and a pollution level of 2 or less (UL standard).

Table 1.5 Installation Site

Type Ambient Operating Temperature Humidity
Enclosed wall-mounted -10 to + 40 °C 95% RH or less (no condensation)
Open chassis -10 to + 45 °C 95% RH or less (no condensation)
Protection covers are attached to the top and bottom of the Inverter. Be sure to remove the protection covers
before installing a 200 or 400 V Class Inverter with an output of 15 kW or less in a panel. Refer to Page 1-17
on how to remove the protection covers.
Observe the following precautions when mounting the Inverter.
• Install the Inverter in a clean location free from oil mist and dust. It can be installed in a totally enclosed
panel that is completely shielded from floating dust.
• When installing or operating the Inverter, always take special care so that metal powder, oil, water, or other
foreign matter does not get into the Inverter.
• Do not install the Inverter on combustible material, such as wood.
• Install the Inverter in a location free from radioactive materials and combustible materials.
• Install the Inverter in a location free from harmful gasses and liquids.
• Install the Inverter in a location without excessive oscillation.
• Install the Inverter in a location free from chlorides.
• Install the Inverter in a location not in direct sunlight.

‹ Controlling the Ambient Temperature

To enhance the reliability of operation, the Inverter should be installed in an environment free from extreme
temperature increases. If the Inverter is installed in an enclosed environment, such as a box, use a cooling fan
or air conditioner to maintain the internal air temperature below 45°C.

‹ Protecting the Inverter from Foreign Matter

Place a cover over the Inverter during installation to shield it from metal powder produced by drilling.
Always remove the cover from the Inverter after completing installation. Otherwise, ventilation will be
reduced, causing the Inverter to overheat.

1-9
 Installation Orientation and Space
Install the Inverter vertically so as not to reduce the cooling effect. When installing the Inverter, always
provide the following installation space to allow normal heat dissipation.

A mm min. B mm min.

Air

30 mm min. 30 mm min. 120 mm min.

Air

Horizontal Space Vertical Space

200 V Class Inverters of 110 kW or 400 V Class Inverters of 160 to 220 kW*: A = 120, B = 120
400 V Class Inverters of 300 kW*: A = 300, B = 300
All other Inverters*: A = 50, B = 120

*If, however, there is a fan in the top of the control panel with sufficient exhaust capacity, the following
dimensions may be used: A = 50, B = 120.
Fig 1.8 Inverter Installation Orientation and Space

1. The same space is required horizontally and vertically for both Open Chassis (IP00) and Enclosed Wall-
mounted [IP20, NEMA 1 (Type 1)] Inverters.
2. Always remove the protection covers before installing a 200 or 400 V Class Inverter with an output of
IMPORTANT 15 kW or less in a panel. Refer to Page 1-17 on how to remove the protection covers.
Always provide enough space for suspension eye bolts and the main circuit lines when installing a 200 or
400 V Class Inverter with an output of 18.5 kW or more in a panel.

1-10
 Removing and Attaching the Terminal Cover

Removing and Attaching the Terminal Cover

Remove the terminal cover to wire cables to the control circuit and main circuit terminals.

‹ Removing the Terminal Cover

„ Inverters of 15 kW or Less
Loosen the screws at the bottom of the terminal cover, press in on the sides of the terminal cover in the direc-
tion indicated by arrow 1, and then lift the terminal cover up to an angle of about 30 degrees in the direction
indicated by arrow 2.
Remove the terminal cover in the direction indicated by arrow 3.

2
1 Approx. 30°

Fig 1.9 Removing the Terminal Cover (Model CIMR-G7B23P7 Shown Above)

„ Inverters of 18.5 kW or More

Loosen the screws on the left and right at the top of the terminal cover, pull out the terminal cover in the direc-
tion of arrow 1 and then lift up on the terminal in the direction of arrow 2.

1
2

Fig 1.10 Removing the Terminal Cover (Model CIMR-G7B2018 Shown Above)

1-11
 ‹ Attaching the Terminal Cover
When wiring the terminal block has been completed, attach the terminal cover by reversing the removal proce-
dure.
For Inverters with an output of 15 kW or less, insert the tab on the top of the terminal cover into the grove on
the Inverter and press in on the bottom of the terminal cover until it clicks into place.

1-12
 Removing/Attaching the Digital Operator and Front Cover

Removing/Attaching the Digital Operator and

Front Cover
The methods of removing and attaching the Digital Operator and Front Cover are described in this sec-
tion.

‹ Inverters of 15 kW or Less
To attach optional boards or change the terminal board connector, remove the Digital Operator and front cover
in addition to the terminal cover. Always remove the Digital Operator from the front cover before removing
the terminal cover.
The removal and attachment procedures are given below.

„Removing the Digital Operator

Press the lever on the side of the Digital Operator in the direction of arrow 1 to unlock the Digital Operator
and lift the Digital Operator in the direction of arrow 2 to remove the Digital Operator as shown in the follow-
ing illustration.

2
1

Fig 1.11 Removing the Digital Operator (Model CIMR-G7B43P7 Shown Above)

1-13
 „Removing the Front Cover
Press the left and right sides of the front cover in the directions of arrows 1 and lift the bottom of the cover in
the direction of arrow 2 to remove the front cover as shown in the following illustration.

1
2

Fig 1.12 Removing the Front Cover (Model CIMR-G7B43P7 Shown Above)

„Mounting the Front Cover

After wiring the terminals, mount the front cover to the Inverter by performing in reverse order to the steps to
remove the front cover.
1. Do not mount the front cover with the Digital Operator attached to the front cover; otherwise, Digital
Operator may malfunction due to imperfect contact.
2. Insert the tab of the upper part of the front cover into the groove of the Inverter and press the lower part of
the front cover onto the Inverter until the front cover snaps shut.

„Mounting the Digital Operator

After attaching the front cover, mount the Digital Operator onto the Inverting using the following procedure.
1. Hook the Digital Operator at A (two locations) on the front cover in the direction of arrow 1 as shown in
the following illustration.
2. Press the Digital Operator in the direction of arrow 2 until it snaps in place at B (two locations).

1-14
 Removing/Attaching the Digital Operator and Front Cover

A
1
B

Fig 1.13 Mounting the Digital Operator

1. Do not remove or attach the Digital Operator or mount or remove the front cover using methods other than
those described above, otherwise the Inverter may break or malfunction due to imperfect contact.
2. Never attach the front cover to the Inverter with the Digital Operator attached to the front cover. Imperfect
IMPORTANT contact can result.
Always attach the front cover to the Inverter by itself first, and then attach the Digital Operator to the front
cover.

1-15
 ‹ Inverters of 18.5 kW or More
For Inverter with an output of 18.5 kW or more, remove the terminal cover and then use the following proce-
dures to remove the Digital Operator and front cover.

„Removing the Digital Operator

Use the same procedure as for Inverters with an output of 18.5 kW or less.

„Removing the Front Cover

Lift up at the location label 1 at the top of the control circuit terminal board in the direction of arrow 2.

Fig 1.14 Removing the Front Cover (Model CIMR-G7B2018 Shown Above)

„ Attaching the Front Cover

After completing required work, such as mounting an optional board or setting the control circuit terminal
board, attach the front cover by reversing the procedure to remove it.
1. Confirm that the Digital Operator is not mounted on the front cover. Contact faults can occur if the cover is
attached while the Digital Operator is mounted to it.
2. Insert the tab on the top of the front cover into the slot on the Inverter and press in on the cover until it
clicks into place on the Inverter.

„Attaching the Digital Operator

Use the same procedure as for Inverters with an output of 15 kW or less.

1-16
 Removing and Attaching the Protection Cover

Removing and Attaching the Protection Cover

Inverters of 15 kW or less have protection covers on the top and bottom as shown in Fig. 1.4.Always
remove the protection covers before installing an Inverter of 15 kW or less in a panel. Use the following
procedure to remove and attach a protection cover.

‹ Removing the Protection Cover

„Top Protection Cover

Insert the tip of the straightedge screwdriver in the slot. Then, lift the cover up in the direction shown by the
arrow to remove it.

Slot

Fig 1.15 Removing the Top Protection Cover (Model CIMR-G7B43P7 Shown Above)

„Bottom Protection Cover

1. Remove the terminal cover as described on Page 1-11.
2. Loosen the two screws, and remove the protection cover.
3. Return the screws to their original position and tighten (them).
4. Reattach the terminal cover as described on Page 1-12.

Terminal Cover

Screws

Bottom Protection
Cover

Fig 1.16 Removing the Bottom Protection Cover (Model CIMR-G7B43P7 Shown Above)

1-17
 ‹ Attaching the Protection Cover

„Top Protection Cover

The protection cover has four hooks: two hooks on the bottom and two on the sides. Fit the bottom hooks into
the holes, bend the cover slightly, and press the cover down until the hooks on the side snap.

Holes for bottom hooks

Fig 1.17 Attaching the Top Protection Cover (Model CIMR-G7B43P7 Shown Above)

„Bottom Protection Cover

To attach the bottom protection cover, reverse the procedure used to remove it.

1-18
 Wiring
This chapter describes wiring terminals, main circuit terminal connections, main circuit termi-
nal wiring specifications, control circuit terminals, and control circuit wiring specifications.

Connections to Peripheral Devices..............................2-2

Connection Diagram ....................................................2-3
Terminal Block Configuration .......................................2-5
Wiring Main Circuit Terminals ......................................2-6
Wiring Control Circuit Terminals ................................2-22
Wiring Check .............................................................2-30
Installing and Wiring Option Boards ..........................2-31
 Connections to Peripheral Devices
Examples of connections between the Inverter and typical peripheral devices are shown in Fig 2.1.

Power supply

Molded-case
circuit breaker
or ground fault
interrupter

Magnetic con-
tactor (MC)

AC reactor for power

factor improvement

Zero phase reactor

Braking resistor

Input noise filter

Inverter

Varispeed F7 DC reactor for power

factor improvement

Ground
Output noise filter

Zero phase reactor

Motor

Ground

Fig 2.1 Example Connections to Peripheral Devices

2-2
 Connection Diagram

Connection Diagram
The connection diagram of the Inverter is shown in Fig 2.2.

When using the Digital Operator, the motor can be operated by wiring only the main circuits.

Thermal relay
Thermal switch contact trip contact

Braking Unit 3 4 1 2

(optional) + +0 P

Level
detector -0 B
Motor
2MCCB Braking Resistor Unit
FU - (optional)
FU Cooling fan
FV
FW FV IM
+1 +3 -
FW
1MCCB MC
3-phase power R R/L1 Inverter U/T1 U

200 to 240 V V
S S/L2 CIMR-G7B2018 V/T2 IM
50/60 Hz
T T/L3 W
W/T3

ON
Forward Run/Stop S1
2MCCB THRX OFF MC (Ground to 100 max.)
MC PG-B2 TA1
SA Reverse Run/Stop S2
Thermal relay trip contact (optional) 1 C
for Braking Resistor Unit Thermal switch contact 2 H
THRX for Braking Unit 3 B
1 2 4 G
Thermal relay trip contact SA External fault 3 4
S3 5 A
PG
for motor cooling fan 6 F

1 2
Fault reset S4 TA3 D

MC TRX Shieded twisted-pair

Multi-step speed reference 1 TA2 wires
1
SA (Main speed switching) g)) S5 Pulse monitor output
2 Pulse A
TRX Multi-step speed 3
30 mA max.
reference 2 S6 4 Pulse B Wiring d
distance::
MCC MA
Fault contact 30 m max.
Jog frequency
selection S7
Multi-function External
contact inputs baseblock command S8 MP
Factory Pulse train output
settings Multi-step speed
reference 3 S9 0 to 32 kHz (2.2 kΩ)
AC Default: Output
Multi-step speed frequency
reference 4 S10

Ammeter adjustment
Acc/dec time 1 S11 AM 20 kΩ
Multi-function analog output 2
-10 to 10 V 2 mA
Emergency stop (NO) S12 − + Default: Output current
AM 0 to +10 V
CN5 (NPN setting) +24V 8mA
Ammeter adjustment
FM 20 kΩ
SC Multi-function analog output 1
AC ? -10 to 10 V 2 mA
FM Default: Output frequency
0 to +10 V
+24V
E (G) E(G)
Shield wire
connection terminal
Error contact output
Pulse train input Master speed MA
RP pulse train
MAA 250 VAC, 10 mA min.
Frequency setting ?
0 to 32 kHz (3 kΩ) MB 1 A max. Min. load
2 k Ω adjustment High level: 3.5 to 13.2 V input 30 VAC, 10 mA min. 5 VDC, 10 mA
MC
Frequency MCC 1 A max.
setter +V Frequency setting power
3 +15 V, 20 mA
2kΩ
0 to 10 V M1
External A1 Master speed reference Multi-function contact oputput
2
frequency 1 4 to 20 mA P 0 to 10 V (20 kΩ) 250 VAC, 10 mA min. 1 A max. Min. load
M2
references A2 Master speed reference 30 VAC, 10 mA min. 1 A max. 5 VDC, 10 mA
4 to 20 mA (250 Ω) Default: Running
[0 to 10 V (20 kΩ) input] signal
0 to 10 V P
A3 Multi-function anlog input
0 to 10 V (20 kΩ)
?
P1
P AC Open collector 1
Factory setting:
0V Auxiliary frequency
Default: Zero
command speed

-V (15V 20mA) P2
Open collector 2
Default: Frequency
Terminating agree signal
resistance
PC
Multi-function
R+ open-collector outputs
P3 48 VDC 50 mA max.
R- Open collector 3
MEMOBUS
Factory setting:
communications S+ C3 Inverter operation
RS-485/422 ready
S- P4
Open collector 4
Factory setting:
( C4 minor fault
IG

Fig 2.2 Connection Diagram (Model CIMR-G7B2018 Shown Above)

2-3
 1. Control circuit terminals are arranged as shown below.

IMPORTANT

2. The output current capacity of the +V and −V terminals are 20 mA. Do not short-circuit between the +V, −V,
and AC terminals. Doing so may result in a malfunction or a breakdown of the Inverter.
3. Disable the stall prevention during deceleration (set constant L3-04 to 0) when using a Braking Resistor
Unit. If this user constant is not changed to disable stall prevention, the system may not stop during decel-
eration.
4. Main circuit terminals are indicated with double circles and control circuit terminals are indicated with single
circles.
5. The wiring for a motor with a cooling fan is not required for self-cooling motors.
6. PG circuit wiring (i.e., wiring to the PG-B2 Board) is not required for control without a PG.
7. Sequence input signals S1 to S12 are labeled for sequence connections (0 V common and sinking mode)
for no-voltage contacts or NPN transistors. These are the default settings.
For PNP transistor sequence connections (+24V common and sourcing mode) or to provide a 24-V exter-
nal power supply, refer to Table 2.13.
8. The multi-function analog output is a dedicated meter output for an analog frequency meter, ammeter, volt-
meter, wattmeter, etc. Do not use this output for feedback control or for any other control purpose.
9. DC reactors to improve the input power factor are built into 200 V Class Inverters for 18.5 to 110 kW and
400 V Class Inverters for 18.5 to 300 kW. A DC reactor is thus an option only for Inverters for 15 kW or
less.
10.Set constant L8-01 to 1 when using a breaking resistor (model ERF). When using a Braking Resistor Unit,
a shutoff sequence for the power supply must be made using a thermal relay trip.
11.The minimum permissible load of a multi-function contact output and an error contact output is 10 mA. Use
a multi-function open-collector output for a load less than 10 mA.
12.Do not ground nor connect the AC terminal on the control circuit to the unit. Doing so may result in a mal-
function or a breakdown of the Inverter.
13.If turning off the power only for the main circuit but leaving the power ON for the control circuit, use a sep-
arate power supply for the control circuit and a specially designed Inverter, which are sold as options.
14. indicates shield wire and P indicates twisted-pair shield wire.

2-4
 Terminal Block Configuration

Terminal Block Configuration

The terminal arrangement for 200 V Class Inverters are shown in Fig 2.3 and Fig 2.4.

Control circuit terminals

Main circuit terminals

Charge indicator

Ground terminal

Fig 2.3 Terminal Arrangement (200 V Class Inverter for 0.4 kW Shown Above)

Control circuit terminals

Charge indicator

Main circuit terminals

Ground terminal

Fig 2.4 Terminal Arrangement (200 V Class Inverter for 18.5 kW Shown Above)

2-5
 Wiring Main Circuit Terminals

‹ Applicable Wire Sizes and Closed-loop Connectors

Select the appropriate wires and crimp terminals from to Table 2.3. Refer to instruction manual
TOBPC72060000 for wire sizes for Braking Resistor Units and Braking Units.

Table 2.1 200 V Class Wire Sizes

Inverter Tightening Possible Recom-
Termi- mended
Model Terminal Symbol nal Torque Wire Sizes Wire Size Wire Type
Screws
CIMR-† (N•m) mm2(AWG) mm2 (AWG)
R/L1, S/L2, T/L3, , 1, 2, B1, B2,
2 to 5.5 2
G7B20P4 U/T1, V/T2, W/T3 M4 1.2 to 1.5
(14 to 10) (14)

R/L1, S/L2, T/L3, , 1, 2, B1, B2,

2 to 5.5 2
G7B20P7 U/T1, V/T2, W/T3 M4 1.2 to 1.5
(14 to 10) (14)

R/L1, S/L2, T/L3, , 1, 2, B1, B2,

2 to 5.5 2
G7B21P5 U/T1, V/T2, W/T3 M4 1.2 to 1.5
(14 to 10) (14)

R/L1, S/L2, T/L3, , 1, 2, B1, B2,

2 to 5.5 3.5
G7B22P2 U/T1, V/T2, W/T3 M4 1.2 to 1.5
(14 to 10) (12)

R/L1, S/L2, T/L3, , 1, 2, B1, B2,

2 to 5.5 5.5
G7B23P7 U/T1, V/T2, W/T3 M4 1.2 to 1.5
(14 to 10) (10)

R/L1, S/L2, T/L3, , 1, 2, B1, B2,

8 to 14 8
G7B25P5 U/T1, V/T2, W/T3 M5 2.5
(8 to 6) (8)

R/L1, S/L2, T/L3, , 1, 2, B1, B2,

14 14
G7B27P5 U/T1, V/T2, W/T3 M5 2.5
(6) (6) Power cables,
e.g., 600 V
R/L1, S/L2, T/L3, , 1, 2, U/T1, M6 4.0 to 5.0
22 to 30 22 vinyl power
V/T2, W/T3 (4 to 3) (4) cables
G7B2011 8 to 14
B1, B2 M5 2.5 -
(8 to 6)
22 22
M6 4.0 to 5.0
(4) (4)
R/L1, S/L2, T/L3, , 1, 2, U/T1, M8 9.0 to 10.0
22 to 38 30
V/T2, W/T3 (4 to 2) (3)
G7B2015 8 to 14
B1, B2 M5 2.5 -
(8 to 6)
22 22
M6 4.0 to 5.0
(4) (4)
R/L1, S/L2, T/L3, , 1, U/T1, V/T2, M8 9.0 to 10.0
30 to 60 30
W/T3, R1/L11, S1/L21, T1/L31 (3 to 1) (3)
G7B2018 8 to 22
3 M6 4.0 to 5.0 -
(8 to 4)
22 to 38 22
M8 9.0 to 10.0
(4 to 2) (4)
R/L1, S/L2, T/L3, , 1 U/T1, M8 9.0 to 10.0
50 to 60 50
V/T2, W/T3, R1/L11, S1/L21, T1/L31 (1 to 1/0) (1)
G7B2022 8 to 22
3 M6 4.0 to 5.0 -
(8 to 4)
22 to 38 22
M8 9.0 to 10.0
(4 to 2) (4)

2-6
 Wiring Main Circuit Terminals

Table 2.1 200 V Class Wire Sizes (Continued)

Inverter Tightening Possible Recom-
Termi- mended
Model Terminal Symbol nal Torque Wire Sizes Wire Size Wire Type
Screws
CIMR-† (N•m) mm2(AWG) mm2 (AWG)
R/L1, S/L2, T/L3, , 1 U/T1, M10 17.6 to 22.5
60 to 100 60
V/T2, W/T3, R1/L11, S1/L21, T1/L31 (2/0 to 4/0) (2/0)
5.5 to 22
3 M8 8.8 to 10.8 -
G7B2030 (10 to 4)
30 to 60 30
M10 17.6 to 22.5
(2 to 2/0) (2)
0.5 to 5.5 1.25
r/ 1, / 2 M4 1.3 to 1.4
(20 to 10) (16)
R/L1, S/L2, T/L3, , 1 U/T1, M10 17.6 to 22.5
80 to 125 80
V/T2, W/T3, R1/L11, S1/L21, T1/L31 (3/0 to 250) (3/0)
5.5 to 22
3 M8 8.8 to 10.8 -
G7B2037 (10 to 4)
38 to 60 38
M10 17.6 to 22.5
(1 to 2/0) (1)
0.5 to 5.5 1.25
r/ 1, / 2 M4 1.3 to 1.4
(20 to 10) (16)
R/L1, S/L2, T/L3, , 1, U/T1, V/T2, 50 to 100 50 × 2P
M10 17.6 to 22.5
W/T3, R1/L11, S1/L21, T1/L31 (1/0 to 4/0) (1/0 × 2P)
5.5 to 60
3 M8 8.8 to 10.8 -
G7B2045 (10 to 2/0)
30 to 60 50
M10 17.6 to 22.5
(3 to 4/0) (1/0)
0.5 to 5.5 1.25
r/ 1, / 2 M4 1.3 to 1.4
(20 to 10) (16)
80 to 125 80 × 2P
, 1 M12 31.4 to 39.2
(3/0 to 250) (3/0 × 2P)
R/L1, S/L2, T/L3, U/T1, V/T2, W/T3, 80 to 100 80 × 2P
M10 17.6 to 22.5 Power cables,
R1/L11, S1/L21, T1/L31 (3/0 to 4/0) (3/0 × 2P)
e.g., 600 V
G7B2055 5.5 to 60
3 M8 8.8 to 10.8 - vinyl power
(10 to 2/0)
cables
80 to 200 80
M12 17.6 to 22.5
(2/0 to 400) (2/0)
0.5 to 5.5 1.25
r/ 1, / 2 M4 1.3 to 1.4
(20 to 10) (16)
150 to 200 150 × 2P
R/L1, S/L2, T/L3, , 1 M12 31.4 to 39.2
(250 to 350) (250 × 2P)
U/T1, V/T2, W/T3, R1/L11, S1/L21, 100 to 150 100 × 2P
M12 31.4 to 39.2
T1/L31 (4/0 to 300) (4/0 × 2P)
G7B2075 5.5 to 60
3 M8 8.8 to 10.8 -
(10 to 2/0)
60 to 150 60 × 2P
M12 31.4 to 39.2
(2/0 to 300) (2/0 × 2P)
0.5 to 5.5 1.25
r/ 1, / 2 M4 1.3 to 1.4
(20 to 10) (16)
200 × 2P, or
200 to 325 50 × 4P
R/L1, S/L2, T/L3, , 1 M12 31.4 to 39.2
(350 to 600) (350 × 2P,
or 1/0 × 4P)
150 × 2P, or
U/T1, V/T2, W/T3, R1/L11, S1/L21, 150 to 325 50 × 4P
M12 31.4 to 39.2
T1/L31 (300 to 600) (300 × 2P,
G7B2090
or 1/0 × 4P)
5.5 to 60
3 M8 8.8 to 10.8 -
(10 to 2/0)
150 150 × 2P
M12 31.4 to 39.2
(300) (300 × 2P)
0.5 to 5.5 1.25
r/ 1, / 2 M4 1.3 to 1.4
(20 to 10) (16)

2-7
 Table 2.1 200 V Class Wire Sizes (Continued)
Inverter Tightening Possible Recom-
Termi- mended
Model Terminal Symbol nal Torque Wire Sizes Wire Size Wire Type
Screws
CIMR-† (N•m) mm2(AWG) mm2 (AWG)
200 × 2P, or
200 to 325 50 × 4P
R/L1, S/L2, T/L3, , 1 M12 31.4 to 39.2
(350 to 600) (350 × 2P,
or 1/0 × 4P)
150 × 2P, or Power cables,
U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/ 150 to 325 50 × 4P e.g., 600 V
M12 31.4 to 39.2
L31 (300 to 600) (300 × 2P, vinyl power
G7B2110
or 1/0 × 4P) cables
5.5 to 60
3 M8 8.8 to 10.8 -
(10 to 2/0)
150 150 × 2P
M12 31.4 to 39.2
(300) (300 × 2P)
0.5 to 5.5 1.25
r/ 1, / 2 M4 1.3 to 1.4
(20 to 10) (16)
* The wire thickness is set for copper wires at 75°C.

2-8
 Wiring Main Circuit Terminals

Table 2.2 400 V Class Wire Sizes

Inverter Tightening Possible Recom-
Termi- mended
Model Terminal Symbol nal Torque Wire Sizes Wire Size Wire Type
Screws
CIMR-† (N•m) mm2 (AWG) mm2 (AWG)
R/L1, S/L2, T/L3, , 1, 2, B1, B2,
2 to 5.5 2
G7B40P4 U/T1, V/T2, W/T3 M4 1.2 to 1.5
(14 to 10) (14)

R/L1, S/L2, T/L3, , 1, 2, B1, B2,

2 to 5.5 2
G7B40P7 U/T1, V/T2, W/T3 M4 1.2 to 1.5
(14 to 10) (14)

R/L1, S/L2, T/L3, , 1, 2, B1, B2,

2 to 5.5 2
G7B41P5 U/T1, V/T2, W/T3 M4 1.2 to 1.5
(14 to 10) (14)

R/L1, S/L2, T/L3, , 1, 2, B1, B2, 3.5

U/T1, V/T2, W/T3 2 to 5.5 (12)
G7B42P2 M4 1.2 to 1.5
(14 to 10) 2
(14)
R/L1, S/L2, T/L3, , 1, 2, B1, B2,
2 to 5.5 3.5
G7B43P7 U/T1, V/T2, W/T3 M4 1.2 to 1.5
(14 to 10) (12)

R/L1, S/L2, T/L3, , 1, 2, B1, B2,

3.5 to 5.5 5.5
G7B45P5 U/T1, V/T2, W/T3 M4 1.2 to 1.5
(12 to 10) (10)

R/L1, S/L2, T/L3, , 1, 2, B1, B2,

5.5 to 14 8
G7B47P5 U/T1, V/T2, W/T3 M5 2.5
(10 to 6) (8)

R/L1, S/L2, T/L3, , 1, 2, B1, B2, M5 2.5

8 to 14 8
Power cables,
U/T1, V/T2, W/T3 (8 to 6) (8)
G7B4011 e.g., 600 V
M5 2.5 5.5 to 14 5.5
vinyl power
(M6) (4.0 to 5.0) (10 to 6) (10)
cables
R/L1, S/L2, T/L3, , 1, 2, U/T1, M5 4.0 to 5.0
8 to 14 8
V/T2, W/T3 (8 to 6) (8)
G7B4015 8 8
B1, B2 M5 2.5
(8) (8)
M5 8 to 22 8
4.0 to 5.0
(M6) (8 to 4) (8)
R/L1, S/L2, T/L3, , 1, 3, U/T1, M6 4.0 to 5.0
14 to 22 14
V/T2, W/T3, R1/L11, S1/L21, T1/L31 (6 to 4) (6)
G7B4018
14 to 38 14
M8 9.0 to 10.0
(6 to 2) (6)
R/L1, S/L2, T/L3, , 1, 3, U/T1, M6 4.0 to 5.0
22 22
V/T2, W/T3, R1/L11, S1/L21, T1/L31 (4) (4)
G7B4022
22 to 38 22
M8 9.0 to 10.0
(4 to 2) (4)
R/L1, S/L2, T/L3, , 1, U/T1, V/T2, M8 9.0 to 10.0
22 to 60 38
W/T3, R1/L11, S1/L21, T1/L31 (4 to 1/0) (2)
G7B4030 8 to 22
3 M6 4.0 to 5.0 -
(8 to 4)
22 to 38 22
M8 9.0 to 10.0
(4 to 2) (4)
R/L1, S/L2, T/L3, , 1, U/T1, V/T2, M8 9.0 to 10.0
30 to 60 38
W/T3, R1/L11, S1/L21, T1/L31 (2 to 1/0) (2)
G7B4037 8 to 22
3 M6 4.0 to 5.0 -
(8 to 4)
22 to 38 22
M8 9.0 to 10.0
(4 to 2) (4)

2-9
 Table 2.2 400 V Class Wire Sizes (Continued)
Inverter Tightening Possible Recom-
Termi- mended
Model Terminal Symbol nal Torque Wire Sizes Wire Size Wire Type
Screws
CIMR-† (N•m) mm2 (AWG) mm2 (AWG)
R/L1, S/L2, T/L3, , 1, U/T1, V/T2, M8 9.0 to 10.0
50 to 60 50
W/T3, R1/L11, S1/L21, T1/L31 (1 to 1/0) (1)
G7B4045 8 to 22
3 M6 4.0 to 5.0 -
(8 to 4)
22 to 38 22
M8 9.0 to 10.0
(4 to 2) (4)
R/L1, S/L2, T/L3, , 1, U/T1, V/T2, M10 17.6 to 22.5
50 to 100 50
W/T3, R1/L11, S1/L21, T1/L31 (1/0 to 4/0) (1/0)
5.5 to 22
3 M8 8.8 to 10.8 -
G7B4055 (10 to 4)
38 to 60 38
M10 17.6 to 22.5
(2 to 2/0) (2)
0.5 to 5.5 1.25
r/ 1, 200/ 2200, 400/ 2400 M4 1.3 to 1.4
(20 to 10) (16)
R/L1, S/L2, T/L3, , 1, U/T1, V/T2, M10 17.6 to 22.5
80 to 100 100
W/T3, R1/L11, S1/L21, T1/L31 (3/0 to 4/0) (4/0)
8 to 22
3 M8 8.8 to 10.8 -
G7B4075 (8 to 4)
50 to 100 50
M10 17.6 to 22.5
(1 to 4/0) (1)
0.5 to 5.5 1.25
r/ 1, 200/ 2200, 400/ 2400 M4 1.3 to 1.4
(20 to 10) (16)
R/L1, S/L2, T/L3, , 1, U/T1, V/T2, 50 to 100 50 × 2P
M10 17.6 to 22.5
W/T3, R1/L11, S1/L21, T1/L33 (1/0 to 4/0) (1/0 × 2P)
8 to 60
3 M8 8.8 to 10.8 - Power cables,
G7B4090 (8 to 2/0)
60 to 150 60 e.g., 600 V
M10 17.6 to 22.5 vinyl power
(2/0 to 300) (2/0)
0.5 to 5.5 1.25 cables
r/ 1, 200/ 2200, 400/ 2400 M4 1.3 to 1.4
(20 to 10) (16)
R/L1, S/L2, T/L3, , 1, U/T1, V/T2, 60 to 100 80 × 2P
M10 17.6 to 22.5
W/T3, R1/L11, S1/L21, T1/L33 (2/0 to 4/0) (3/0 × 2P)
8 to 60
3 M8 8.8 to 10.8 -
G7B4110 (8 to 2/0)
100 to 150 100
M10 17.6 to 22.5
(4/0 to 300) (4/0)
0.5 to 5.5 1.25
r/ 1, 200/ 2200, 400/ 2400 M4 1.3 to 1.4
(20 to 10) (16)
R/L1, S/L2, T/L3, , 1, U/T1, V/T2, 80 to 200 80 × 2P
M12 31.4 to 39.2
W/T3, R1/L11, S1/L21, T1/L31 (3/0 to 400) (3/0 × 2P)
8 to 60
3 M8 8.8 to 10.8 -
G7B4132 (8 to 2/0)
50 to 150 50 × 2P
M12 31.4 to 39.2
(1/0 to 300) (1/0 × 2P)
0.5 to 5.5 1.25
r/ 1, 200/ 2200, 400/ 2400 M4 1.3 to 1.4
(20 to 10) (16)
R/L1, S/L2, T/L3, , 1, U/T1, V/T2, 100 to 200 100 × 2P
M12 31.4 to 39.2
W/T3, R1/L11, S1/L21, T1/L31 (4/0 to 400) (4/0 × 2P)
80 to 60
3 M8 8.8 to 10.8 -
G7B4160 (8 to 2/0)
50 to 150 50 × 2P
M12 31.4 to 39.2
(1/0 to 300) (1/0 × 2P)
0.5 to 5.5 1.25
r/ 1, 200/ 2200, 400/ 2400 M4 1.3 to 1.4
(20 to 10) (16)

2-10
 Wiring Main Circuit Terminals

Table 2.2 400 V Class Wire Sizes (Continued)

Inverter Tightening Possible Recom-
Termi- mended
Model Terminal Symbol nal Torque Wire Sizes Wire Size Wire Type
Screws
CIMR-† (N•m) mm2 (AWG) mm2 (AWG)
100 to 325 150 × 2P
R/L1, S/L2, T/L3 M16 78.4 to 98
(4/0 to 600) (300 × 2P)
U/T1, V/T2, W/T3 100 to 325 125 × 2P
M16 78.4 to 98
R1/L11, S1/L21, T1/L33 (4/0 to 600) (250 × 2P)
100 to 325 200 × 2P
, 1, M16 78.4 to 98
G7B4185 (4/0 to 600) (400 × 2P)
100 to 325
3 M16 78.4 to 98 -
(4/0 to 600)
100 to 325 150
M16 78.4 to 98
(4/0 to 600) (300)
0.5 to 5.5 1.25
r/ 1, 200/ 2200, 400/ 2400 M4 1.3 to 1.4
(20 to 10) (16)
100 to 325 200 × 2P
R/L1, S/L2, T/L3 M16 78.4 to 98
(4/0 to 600) (400 × 2P)
U/T1, V/T2, W/T3 100 to 325 150 × 2P
M16 78.4 to 98
R1/L11, S1/L21, T1/L33 (4/0 to 600) (350 × 2P)
100 to 325 250 × 2P
, 1, M16 78.4 to 98
G7B4220 (4/0 to 600) (500 × 2P)
100 to 325
3 M16 78.4 to 98 - Power cables,
(4/0 to 600)
100 to 325 200 e.g., 600 V
M16 78.4 to 98 vinyl power
(4/0 to 600) (400)
0.5 to 5.5 1.25 cables
r/ 1, 200/ 2200, 400/ 2400 M4 1.3 to 1.4
(20 to 10) (16)
325 × 2P
100 to 325 (600 × 2P),
R/L1, S/L2, T/L3 M16 78.4 to 98
(4/0 to 600) 125 × 4P
(250 × 4P)
325 × 2P
U/T1, V/T2, W/T3 100 to 325 (600 × 2P),
M16 78.4 to 98
R1/L11, S1/L21, T1/L33 (4/0 to 600) 125 × 4P
(250 × 4P)
100 to 325 200 × 4P
G7B4300 , 1, M16 78.4 to 98
(4/0 to 600) (400 × 4P)
100 to 325
3 M16 78.4 to 98 -
(4/0 to 600)
125 × 2P
100 to 325 (250 × 2P),
M16 78.4 to 98
(4/0 to 600) 325
(600)
0.5 to 5.5 1.25
r/ 1, 200/ 2200, 400/ 2400 M4 1.3 to 1.4
(20 to 10) (16)
* The wire thickness is set for copper wires at 75°C.

2-11
 Table 2.3 Closed-loop Connector Sizes (JIS C2805) (200 V Class and 400 V Class)

Wire Thickness (mm2) Terminal Screws Size

M3.5 1.25 to 3.5
0.5
M4 1.25 to 4
M3.5 1.25 to 3.5
0.75
M4 1.25 to 4
M3.5 1.25 to 3.5
1.25
M4 1.25 to 4
M3.5 2 to 3.5
M4 2 to 4
2 M5 2 to 5
M6 2 to 6
M8 2 to 8
M4 5.5 to 4
M5 5.5 to 5
3.5/5.5
M6 5.5 to 6
M8 5.5 to 8
M5 8 to 5
8 M6 8 to 6
M8 8 to 8
M6 14 to 6
14
M8 14 to 8
M6 22 to 6
22
M8 22 to 8
30/38 M8 38 to 8
M8 60 to 8
50/60
M10 60 to 10
80 80 to 10
M10
100 100 to 10
100 100 to 12
150 M12 150 to 12
200 200 to 12
M12 x 2 325 to 12
325
M16 325 to 16

Determine the wire size for the main circuit so that line voltage drop is within 2% of the rated voltage. Line
voltage drop is calculated as follows:

IMPORTANT Line voltage drop (V) = 3 x wire resistance (W/km) x wire length (m) x current (A) x 10-3

2-12
 Wiring Main Circuit Terminals

‹ Main Circuit Terminal Functions

Main circuit terminal functions are summarized according to terminal symbols in Table 2.4. Wire the terminals
correctly for the desired purposes.

Table 2.4 Main Circuit Terminal Functions (200 V Class and 400 V Class)
Model: CIMR-G7B†
Purpose Terminal Symbol
200 V Class 400 V Class
R/L1, S/L2, T/L3 20P4 to 2110 40P4 to 4300
Main circuit power input
R1/L11, S1/L21, T1/L31 2018 to 2110 4018 to 4300
Inverter outputs U/T1, V/T2, W/T3 20P4 to 2110 40P4 to 4300

DC power input 1, 20P4 to 2110 40P4 to 4300

Braking Resistor Unit connec-

B1, B2 20P4 to 2015 40P4 to 4015
tion

DC reactor connection 1, 2 20P4 to 2015 40P4 to 4015

Braking Unit connection 3, 2018 to 2110 4018 to 4300

Ground 20P4 to 2110 40P4 to 4300

Note The 1 and input terminals for the DC power do not conform to UL/cUL standards.

2-13
 ‹ Main Circuit Configurations
The main circuit configurations of the Inverter are shown in Fig 2.5.

Table 2.5 Inverter Main Circuit Configurations

200 V Class 400 V Class

CIMR-G7B20P4 to 2015 CIMRG7B40P4 to 4015

B1 B2
B1 B2

+1
+1
+2 +2
R/L1 U/T1 U/T1
R/L1
S/L2 V/T2 V/T2
S/L2
T/L3 W/T3 W/T3
T/L3
−
−

Power Control
supply circuits Power Control
Cooling fan is provided for supply circuits
Inverters of 2.2 kW or more. Cooling fan is provided for
Inverters of 1.5 kW or more.

CIMR-G7B2018, 2022 CIMR-G7B4018 to 4045

+3 +3

+1 +1

R/L1 R/L1
U/T1 U/T1
S/L2 S/L2
T/L3 V/T2 T/L3 V/T2
R1/L11
W/T3 R1/L11 W/T3
S1/L21
S1/L21
T1/L31
T1/L31
− −

Power Control Power Control

supply circuits supply circuits

CIMR-G7B2030 to 2110 CIMR-G7B4055 to 4300

+3

+1
a a
b b

R/L1
U/T1
S/L2
T/L3 V/T2
R1/L11 W/T3
S1/L21
T1/L31
−
r/ l 1
*
200/ l 2200 Power Control
Power Control supply circuits
a supply circuits 400/ l 2400 a
b b

Note Consult your Yaskawa representative before using 12-phase rectification.

* These terminals are wired before shipment. When using DC power for the main circuit power supply, remove the wires between R-r/ 1 and S- / 2, then,
for 200 V Class Inverters, input 200 VAC to r/ 1- / 2, or, for 400 V Class Inverters, input either 200 VAC to r/ 1- 200/ 2200 or 400 VAC to r/ 1-
400/ 2400.

2-14
 Wiring Main Circuit Terminals

‹ Standard Connection Diagrams

Standard Inverter connection diagrams are shown in Fig 2.5. These are the same for both 200 V Class and
400 V Class Inverters. The connections depend on the Inverter capacity.

„CIMR-G7B20P4 to 2015 and 40P4 to „CIMR-G7B2018, 2022, and 4018 to 4045

4015
Braking Resistor
Braking Resistor Unit (optional)
DC reactor Unit (optional)
Braking Unit
(optional)
(optional)
+ 1 + 2 B1 B2
R/L1 U/T1 +1 +3
S/L2 V/T2 IM R/L1 U/T1
T/L3 W/T3 S/L2 V/T2
3-phase 200 IM
VAC (400 VAC) T/L3 W/T3
3-phase 200 R1/L11
VAC (400 VAC)
S1/L21
T1/L31

Be sure to remove the short-circuit bar before connecting the DC The DC reactor is built in.
reactor.

When connecting a separately-installed type Braking Unit (model CDBR), connect the B1 terminal of the
Inverter to the + terminal of the Braking Unit and connect the − terminal of the Inverter to the − terminal of the
Braking Unit. The B2 terminal is not used in this case.
IMPORTANT

„CIMR-G7B2030 to 2110 „CIMR-G7B4055 to 4300

Braking Resistor Braking Resistor
Unit (optional) Unit (optional)
Braking Unit Braking Unit
(optional) (optional)

+1 +3 +1 +3
R/L1 U/T1 R/L1 U/T1
S/L2 V/T2 S/L2 V/T2
IM IM
T/L3 W/T3 T/L3 W/T3
3-phase R1/L11 3-phase R1/L11
200 VAC 400 VAC
S1/L21 S1/L21
T1/L31 T1/L31
r/l1 r/l1
/l2 200/l2200
400/l2400

Control power is supplied internally from the main circuit DC power supply for all Inverter models.

Fig 2.5 Main Circuit Terminal Connections

If a Braking Unit or a Braking Resistor Unit is connected to a wrong terminal, the Inverter, Braking Unit, or
Braking Resistor Unit can be damaged.

IMPORTANT

2-15
 ‹ Wiring the Main Circuits
This section describes wiring connections for the main circuit inputs and outputs.

„Wiring Main Circuit Inputs

Observe the following precautions for wiring the main circuit power supply inputs.

Installing a Molded-case Circuit Breaker

Always connect the power input terminals (R, S, and T) and power supply via a molded-case circuit breaker
(MCCB) suitable for the Inverter.
• Choose an MCCB with a capacity of 1.5 to 2 times the Inverter's rated current.
• For the MCCB's time characteristics, be sure to consider the Inverter's overload protection (one minute at
150% of the rated output current).
• If the same MCCB is to be used for more than one Inverter, or other devices, set up a sequence so that the
power supply will be turned OFF by a fault output, as shown in Fig 2.6.

Inverter
Power
supply
R/L1
20P4 to 2030: 3-phase,
200 to 240 VAC, 50/60 Hz S/L2
2037 to 2110: 3-phase,
200 to 230 VAC, 50/60 Hz T/L3
40P4 to 4300: 3-phase,
380 to 460 VAC, 50/60 Hz
Fault output
(NC)

* For 400 V Class Inverters, connect a 400/200 V transformer.

Fig 2.6 MCCB Installation

Installing a Ground Fault Interrupter

Inverter outputs use high-speed switching, so high-frequency leakage current is generated. At the Inverter pri-
mary side, use a ground fault interrupter for Inverters with a countermeasure against high frequency to detect
only the leakage current in the frequency range that is hazardous to humans and to ignore high-frequency leak-
age current. Use one or several ground fault interrupters with a total cumulative sensitivity amperage of at
least 30 mA per Inverter.
Using a ground fault interrupter without a countermeasure against high frequency may result in a malfunction
caused by high-frequency leakage current. If a ground fault interrupter without a countermeasure malfunc-
tions, replace it with a ground fault interrupter with a countermeasure against high frequency or reduce the
carrier frequency of the Inverter. Alternatively, use one or several ground fault interrupters with a total cumu-
lative sensitivity amperage of at least 200 mA per Inverter.

2-16
 Wiring Main Circuit Terminals

Installing a Magnetic Contactor

If the power supply for the main circuit is to be shut off during a sequence, a magnetic contactor can be used.
When a magnetic contactor is installed on the primary side of the main circuit to forcibly stop the Inverter,
however, the regenerative braking does not work and the Inverter will coast to a stop.
• The Inverter can be started and stopped by opening and closing the magnetic contactor on the primary side.
Frequently opening and closing the magnetic contactor, however, may cause the Inverter to break down.
Start and stop the Inverter at most once every 30 minutes.
• When the Inverter is operated with the Digital Operator, automatic operation cannot be performed after
recovery from a power interruption.
• If the Braking Resistor Unit is used, program the sequence so that the magnetic contactor is turned OFF by
the contact of the Unit's thermal overload relay.

Connecting Input Power Supply to the Terminal Block

Input power supply can be connected to any terminal R, S or T on the terminal block; the phase sequence of
input power supply is irrelevant to the phase sequence.

Installing an AC Reactor or DC Reactor

If the Inverter is connected to a large-capacity power transformer (600 kW or more) or the phase advancing
capacitor is switched, an excessive peak current may flow through the input power circuit, causing the con-
verter unit to break down.
To prevent this, install an optional AC Reactor on the input side of the Inverter or a DC reactor to the DC reac-
tor connection terminals.
This also improves the power factor on the power supply side.

Installing a Surge Absorber

Always use a surge absorber or diode for inductive loads near the Inverter. These inductive loads include mag-
netic contactors, electromagnetic relays, solenoid valves, solenoids, and magnetic brakes.

Installing a Noise Filter on Power Supply Side

Install a noise filter to eliminate noise transmitted between the power line and the Inverter.
• Correct Noise Filter Installation

Power
supply MCCB
Noise
filter Inverter IM

MCCB
Other
controllers
Use a special-purpose noise filter for Inverters.

Fig 2.7 Correct Power supply Noise Filter Installation

2-17
 • Incorrect Noise Filter Installation

Power
supply MCCB

Inverter IM

MCCB
General-
purpose Other
noise filter controllers

Power
supply MCCB
General-
purpose Inverter IM
noise filter

MCCB
Other
controllers Do not use general-purpose noise filters. No general-
purpose noise filter can effectively suppress noise
generated from the Inverter.

Fig 2.8 Incorrect Power supply Noise Filter Installation

„Wiring the Output Side of Main Circuit

Observe the following precautions when wiring the main output circuits.

Connecting the Inverter and Motor

Connect output terminals U, V, and W to motor lead wires U, V, and W, respectively.
Check that the motor rotates forward with the Forward Run Command. Switch over any two of the output ter-
minals to each other and reconnect if the motor rotates in reverse with the Forward Run Command.

Never Connect a Power Supply to Output Terminals

Never connect a power supply to output terminals U, V, and W. If voltage is applied to the output terminals,
the internal circuits of the Inverter will be damaged.

Never Short or Ground Output Terminals

If the output terminals are touched with bare hands or the output wires come into contact with the Inverter cas-
ing, an electric shock or grounding will occur. This is extremely hazardous. Do not short the output wires.

Do Not Use a Phase Advancing Capacitor or Noise Filter

Never connect a phase advancing capacitor or LC/RC noise filter to an output circuit. The high-frequency
components of the Inverter output may result in overheating or damage to these part or may result in damage
to the Inverter or cause other parts to burn.

Do Not Use a Magnetic Contactor

Never connect a magnetic contactor between the Inverter and motor and turn it ON or OFF during operation.
If the magnetic contactor is turned ON while the Inverter is operating, a large inrush current will be created
and the overcurrent protection in the Inverter will operate.
When using a magnetic contactor to switch to a commercial power supply, stop the Inverter and motor before
operating the magnetic contactor. Use the speed search function if the magnetic contactor is operated during

2-18
 Wiring Main Circuit Terminals

operation. If measures for momentary power interrupts are required, use a delayed release the magnetic con-
tactor.

Installing a Thermal Overload Relay

This Inverter has an electronic thermal protection function to protect the motor from overheating. If, however,
more than one motor is operated with one Inverter or a multi-polar motor is used, always install a thermal
relay (THR) between the Inverter and the motor and set L1-01 to 0 (no motor protection). The sequence
should be designed so that the contacts of the thermal overload relay turn OFF the magnetic contactor on the
main circuit inputs.

Installing a Noise Filter on Output Side

Connect a noise filter to the output side of the Inverter to reduce radio noise and inductive noise.

Power
supply MCCB
Inverter Noise
filter IM
Radio noise
AM radio
Inductive
Signal line noise

Controller

Inductive Noise: Electromagnetic induction generates noise on the signal line, causing the controller to malfunction.
Radio Noise: Electromagnetic waves from the Inverter and cables cause the broadcasting radio receiver to make
noise.

Fig 2.9 Installing a Noise Filter on the Output Side

Countermeasures Against Inductive Noise

As described previously, a noise filter can be used to prevent inductive noise from being generated on the out-
put side. Alternatively, cables can be routed through a grounded metal pipe to prevent inductive noise. Keep-
ing the metal pipe at least 30 cm away from the signal line considerably reduces inductive noise.

Power MCCB Metal pipe

supply
Inverter IM

30 cm min.
Signal line
Controller

Fig 2.10 Countermeasures Against Inductive Noise

2-19
 Countermeasures Against Radio Interference
Radio noise is generated from the Inverter as well as from the input and output lines. To reduce radio noise,
install noise filters on both input and output sides, and also install the Inverter in a totally enclosed steel box.
The cable between the Inverter and the motor should be as short as possible.

Steel box
Power Metal pipe
supply MCCB
Noise Inverter Noise
filter filter IM

Fig 2.11 Countermeasures Against Radio Interference

Cable Length between Inverter and Motor

If the cable between the Inverter and the motor is long, the high-frequency leakage current will increase, caus-
ing the Inverter output current to increase as well. This may affect peripheral devices. To prevent this, adjust
the carrier frequency (set in C6-02) as shown in Table 2.6. (For details, refer to Chapter 5 User Constants.)

Table 2.6 Cable Length between Inverter and Motor

Cable length 50 m max. 100 m max. More than 100 m
Carrier frequency 15 kHz max. 10 kHz max. 5 kHz max.

„Ground Wiring
Observe the following precautions when wiring the ground line.
• Always use the ground terminal of the 200 V Inverter with a ground resistance of less than 100 Ω and that
of the 400 V Inverter with a ground resistance of less than 10 Ω.
• Do not share the ground wire with other devices, such as welding machines or power tools.
• Always use a ground wire that complies with technical standards on electrical equipment and minimize the
length of the ground wire.
Leakage current flows through the Inverter. Therefore, if the distance between the ground electrode and the
ground terminal is too long, potential on the ground terminal of the Inverter will become unstable.
• When using more than one Inverter, be careful not to loop the ground wire.

OK NO

Fig 2.12 Ground Wiring

2-20
 Wiring Main Circuit Terminals

„Connecting the Braking Resistor (ERF)

A Braking Resistor that mounts to the Inverter can be used with 200 V and 400 V Class Inverters with outputs
from 0.4 to 3.7 kW.
Connect the braking resistor as shown in Fig 2.13.

Table 2.7

L8-01 (Protect selection for internal DB resistor) 1 (Enables overheat protection)

L3-04 (Stall prevention selection during deceleration) 0 (Disables stall prevention function)
(Select either one of them.) 3 (Enables stall prevention function with braking resistor)

Inverter Braking resistor

Fig 2.13 Connecting the Braking Resistor

The braking resistor connection terminals are B1 and B2. Do not connect to any other terminals. Connecting
to any terminals other than B1 or B2 can cause the resistor to overheat, resulting in damage to the equip-
ment.
IMPORTANT

„Connecting the Braking Resistor Unit (LKEB) and Braking Unit (CDBR)
Use the following settings when using a Braking Resistor Unit. Refer to Wiring Examples on page 10-20 for
connection methods for a Braking Resistor Unit.
A Braking Resistor that mounts to the Inverter can also be used with Inverters with outputs from 0.4 to
3.7 kW.

Table 2.8

L8-01 (Protect selection for internal DB resistor) 0 (Disables overheat protection)

L3-04 (Stall prevention selection during deceleration) 0 (Disables stall prevention function)
(Select either one of them.) 3 (Enables stall prevention function with braking resistor)
L8-01 is used when a braking resistor without thermal overload relay trip contacts (ERF type mounted to
Inverter) is connected.
The Braking Resistor Unit cannot be used and the deceleration time cannot be shortened by the Inverter if L3-
04 is set to 1 (i.e., if stall prevention is enabled for deceleration).

2-21
 Wiring Control Circuit Terminals

‹ Wire Sizes and Closed-loop Connectors

For remote operation using analog signals, keep the control line length between the Digital Operator or opera-
tion signals and the Inverter to 50 m or less, and separate the lines from high-power lines (main circuits or
relay sequence circuits) to reduce induction from peripheral devices.
When setting frequencies from an external frequency setter (and not from a Digital Operator), use shielded
twisted-pair wires and ground the shield to terminal E (G), as shown in the following diagram.

Shield terminal
E(G)

㧗V Speed setting power supply, +15 V 20 mA

2kΩ
2kΩ A1 Master speed reference 0 to 10 V (-10 to 10 V)

A2 Master speed reference 4 to 20 㨙A

(0 to 10 V, -10 to 10 V)

2kΩ
2kΩ
A3 Auxiliary reference 0 to 10 V (-10 to 10 V)

RP Pulse train input 32 kHz max.

P P P P
AC Analog common

-V Speed setting power supply -15 V 20 mA

Fig 2.14

Terminal numbers and wire sizes are shown in Table 2.9.

Table 2.9 Terminal Numbers and Wire Sizes (Same for all Models)
Recom-
Termi- Tightening Possible Wire
mended
Terminals nal Torque Sizes Wire Type
Wire Size
Screws (N•m) mm2(AWG)
mm2(AWG)
FM, AC, AM, P1, P2,
PC, SC, A1, A2, A3, +V,
-V, S1, S2, S3, S4, S5, S6, M3.5 0.8 to 1.0 0.5 to 2*2 0.75
(20 to 14) (18)
S7, S8, MA, MB, MC,
M1, M2 • Shielded, twisted-pair wire*1
Single wire*3: • Shielded, polyethylene-cov-
P3, C3, P4, C4, MP, RP, 0.14 to 2.5 ered, vinyl sheath cable
Phoenix 0.75 (KPEV-S by Hitachi Electri-
R+, R-, S9, S10, S11, 0.5 to 0.6 Stranded wire:
type (18) cal Wire or equivalent)
S12, S+, S-, IG 0.14 to 1.5
(26 to 14)

E (G) M3.5 0.8 to 1.0 0.5 to 2*2 1.25

(20 to 14) (12)
* 1. Use shielded twisted-pair cables to input an external frequency reference.
* 2. Refer to Table 2.3 Closed-loop Connector Sizes (JIS C2805) (200 V Class and 400 V Class) for suitable closed-loop crimp terminal sizes for the wires.
* 3. We recommend using straight solderless terminal on signal lines to simplify wiring and improve reliability.

2-22
 Wiring Control Circuit Terminals

„ Straight Solderless Terminals for Signal Lines

Models and sizes of straight solderless terminal are shown in the following table.

Table 2.10 Straight Solderless Terminal Sizes

Wire Size mm2 (AWG) Model d1 d2 L Manufacturer

0.25 (24) AI 0.25 - 8YE 0.8 2 12.5
0.5 (20) AI 0.5 - 8WH 1.1 2.5 14
0.75 (18) AI 0.75 - 8GY 1.3 2.8 14 Phoenix Contact
1.25 (16) AI 1.5 - 8BK 1.8 3.4 14
2 (14) AI 2.5 - 8BU 2.3 4.2 14

d1

d2

Fig 2.15 Straight Solderless Terminal Sizes

„Wiring Method
Use the following procedure to connect wires to the terminal block.
1. Loosen the terminal screws with a thin-slot screwdriver.
2. Insert the wires from underneath the terminal block.
3. Tighten the terminal screws firmly.

Thin-slot screwdriver Blade of screwdriver

Control circuit
terminal block

Strip the end for

7 mm if no sold-
erless terminal is
used. Solderless terminal or wire 3.5 mm max.
without soldering
Wires Blade thickness: 0.6 mm max.

Fig 2.16 Connecting Wires to Terminal Block

2-23
 ‹ Control Circuit Terminal Functions
The functions of the control circuit terminals are shown in Table 2.11. Use the appropriate terminals for the
correct purposes.

Table 2.11 Control Circuit Terminals

Type No. Signal Name Function Signal Level
S1 Forward Run/Stop Command Forward run when ON; stopped when OFF.
S2 Reverse Run/Stop Command Reverse run when ON; stopped when OFF.

S3 Multi-function input 1*1 Factory setting: External fault when ON.

S4 Multi-function input 2*1 Factory setting: Fault reset when ON.

Factory setting: Multi-speed reference 1

S5 Multi-function input 3*1 effective when ON.
Factory setting: Multi-speed reference 2
S6 Multi-function input 4*1 effective when ON.
Factory setting: Jog frequency selected when
Se-
S7 Multi-function input 5*1 ON.
quence 24 VDC, 8 mA
input
signals Factory setting: External baseblock when Photocoupler isolation
S8 Multi-function input 6*1 ON.
Factory setting: Multi-speed reference 3
S9 Multi-function input 7*1 effective when ON.
Factory setting: Multi-speed reference 4
S10 Multi-function input 8*1 effective when ON.
Factory setting: Acceleration/deceleration
S11 Multi-function input 9*1 time selected when ON.
Factory setting: Emergency stop (NO con-
S12 Multi-function input 10*1 tact) when ON.
SC Sequence input common -
+15 V
+V +15 V power output +15 V power supply for analog references
(Max. current: 20 mA)
-15 V
-V -15 V power output -15 V power supply for analog references
(Max. current: 20 mA)
-10 to +10 V, 0 to +10 V
Master speed frequency ref- -10 to +10 V/-100 to 100%
A1 (Input impedance:
erence 0 to +10 V/100%
20 kΩ)
4 to 20 mA (Input imped-
4 to 20 mA/100%, -10 to +10 V/-100 to
ance: 250 Ω)
Analog +100%, 0 to +10 V/100%
input A2 Multi-function analog input -10 to +10 V, 0 to +10 V
signals Factory setting: Added to terminal A1
(Input impedance:
(H3-09 = 0)
20 kΩ)
-10 to +10 V/-100 to +100%, 0 to +10 V/
-10 to +10 V, 0 to +10 V
100%
A3 Multi-function analog input (Input impedance:
Factory setting: Auxiliary speed frequency
20 kΩ)
reference 1 (H3-05 = 2)
AC Analog reference common 0V -
Shield wire, optional ground
E(G) - -
line connection point

2-24
 Wiring Control Circuit Terminals

Table 2.11 Control Circuit Terminals (Continued)

Type No. Signal Name Function Signal Level
Factory setting: Zero-speed
P1 Multi-function PHC output 1
Zero-speed level (b2-01) or below when ON.
Factory setting: Frequency agreement detec-
tion
P2 Multi-function PHC output 2
Frequency within 2 Hz of set frequency
when ON.
Photo-
coupler
PC
Photocoupler output common
- 50 mA max. at 48 VDC*2
outputs
for P1 and P2
P3 Factory setting: Ready for operation when
Multi-function PHC output 3
C3 ON.

P4
Multi-function PHC output 4 Factory setting: Minor fault.
C4
Fault output signal (NO con-
MA
tact) Fault when CLOSED across MA and MC Dry contacts
Fault output signal (NC con- Fault when OPEN across MB and MC Contact capacity:
MB 10 mA min. 1 A max. at
tact)
Relay 250 VAC
outputs Relay contact output com- 10 mA min. 1 A max. at
MC -
mon 30 VDC
Minimum permissible
M1
Multi-function contact output Factory setting: Operating load: 5 VDC, 10 mA*4
(NO contact) Operating when ON across M1 and M2.
M2

Multi-function analog moni- Factory setting: Output frequency

FM
tor 1 0 to 10 V/100% frequency
Analog
moni- -10 to +10 VDC ±5%
Multi-function analog moni- Factory setting: Current monitor
tor out- AM 2 mA max.
puts tor 2 5 V/Inverter's rated current
AC Analog common -
Factory setting: Frequency reference input
RP Multi-function pulse input*3 (H6-01 = 0)
0 to 32 kHz (3 kΩ)
Pulse
I/O Factory setting: Output frequency
MP Multi-function pulse monitor 0 to 32 kHz (2.2 kΩ)
(H6-06 = 2)
R+ MEMOBUS communica- Differential input, photo-
R- tions input coupler isolation
RS- For 2-wire RS-485, short R+ and S+ as well
485/ S+ as R- and S-.
MEMOBUS communica- Differential output, pho-
422 tions output tocoupler isolation
S-
IG Communications shield wire - -
* 1. For a 3-wire sequence, the default settings are a 3-wire sequence for S5, multi-step speed setting 1 for S6 and multi-step speed setting 2 for S7, and jog
frequency command for S8.
* 2. When driving a reactive load, such as a relay coil, always insert a flywheel diode as shown in Fig 2.17.
* 3. Pulse input specifications are given in the following table.
* 4. Use the photocoupler outputs when the minimum permissible load is 5 VDC or less and 10 mA or less.

Low level voltage 0.0 to 0.8 V

High level voltage 3.5 to 13.2 V
H duty 30% to 70%
Pulse frequency 0 to 32 kHz

2-25
 Flywheel diode

The rating of the flywheel diode

Coil must be at least as high as the
External power:
48 V max. 50 mA max. circuit voltage.

Fig 2.17 Flywheel Diode Connection

„Shunt Connector CN5 and DIP Switch S1

The shunt connector CN 5 and DIP switch S1 are described in this section.

CN5 S1
O OFF ON Terminating resistance
F 1
F 2 V I Analog input switch
: Factory settings

Note: Refer to Table 2.12 for S1

functions and to Table
2.13 for CN5 functions.

Fig 2.18 Shunt Connector CN5 and DIP Switch S1

The functions of DIP switch S1 are shown in the following table.

Table 2.12 DIP Switch S1

Name Function Setting
RS-485 and RS-422 terminating resis- OFF: No terminating resistance
S1-1
tance ON: Terminating resistance of 110 Ω

OFF: 0 to 10 V, -10 to 10 V (internal resistance: 20 kΩ)

S1-2 Input method for analog input A2
ON: 4 to 20 mA (internal resistance: 250 Ω)

„ Sinking/Sourcing Mode
The input terminal logic can be switched between sinking mode (0-V common) and sourcing mode (+24-V
common) if shunt connector CN5 is used. An external 24-V power supply is also supported, providing more
freedom in signal input methods.

2-26
 Wiring Control Circuit Terminals

Table 2.13 Sinking/Sourcing Mode and Input Signals

Internal Power Supply External Power Supply

CN5 CN5
CN5 (NPN set) Factory setting CN5 (EXT set)

Shunt IP24V (24 V)

position IP24V (24 V) External +24 V
SC SC

Sink-
ing
Mode S1 S1

S2 S2

CN5 CN5

CN5 (PNP set) CN5 (EXT set)

External + 24 V IP24V (24 V)

IP24V (24 V)
SC SC

Sourc-
ing
Mode S1 S1

S2 S2

2-27
 ‹ Control Circuit Terminal Connections
Connections to Inverter control circuit terminals are shown in Fig 2.19.

Inverter
CIMR-G7B2018

Forward Run/Stop S1

Reverse Run/Stop S2
Thermal switch contact
for Braking Unit
3 4
External fault S3

Fault reset S4
Multi-step command 1
(Main speed switching)
S5
Multi-step speed
setting 2 S6
Jog frequency
selection S7
Multi-function External
contact input baseblock command S8 MP
Defaults Pulse train output
Multi-step speed
setting 3 S9 0 to 32 kHz (2.2 kΩ)
AC Default: Output
frequency
Multi-step speed
setting 4 S10

Acc/dec time 1 Ammeter adjustment

S11 AM 20 kΩ
Multi-function analog output 2
-10 to 10 V 2 mA
Emergency stop (NO) S12 − + Default: Output current
AM 0 to +10 V
+24V 8mA
CN5 (NPN setting) Ammeter adjustment
FM 20 kΩ
SC Multi-function analog output 1
AC − + -10 to 10 V 2 mA
FM Default: Output current
0 to +10 V
+24V
E(G) E(G)
Shield wire
connection terminal
Pulse train input MA
RP Master speed pulse train MA
Error contact output
Frequency setting 0 to 32 kHz (3 kΩ) MB 250 VAC, 10 mA min. 1 A max. Min. load
2 kΩ adjustment High level: 3.5 to 13.2 V
input MC 30 VDC, 10 mA min. 1 A max. 5 VDC, 10 mA
MC
Frequency
setter +V Frequency setting power
3 +15 V 20 mA
0 to 10 V M1
External 2 kΩ A1 Master speed reference Multi-function contact output
2
frequency 1 4 to 20 mA P 0 to 10 V (20 kΩ) 250 VAC, 10 mA min. 1 A max. Min. load
M2
references A2 Master speed reference 30 DC, 10 mA min. 1 A max. 5 VDC, 10 mA
4 to 20 mA (250 Ω) Default: Running
[0 to 10 V (20 kΩ) input] signal
0 to 10 V P
A3 Multi-function anlog input
P1
P 0 to 10 V (20 kΩ) Open collector 1
AC
0V Factory setting: Default: Zero
Auxiliary frequency
command speed
-V (−15V 20mA) P2
Open collector 2
Default:
Terminating
resistance PC Frequency
agree signal Multi-function
R+ open-collector outputs
P3 Open collector 3
R- 48 VDC, 50 mA
MEMOBUS Factory setting:
communications S+ C3 Inverter operation
ready
RS-485/422
S- P4 Open collector 4
Factory setting:
C4 Minor fault
IG

Fig 2.19 Control Circuit Terminal Connections

2-28
 Wiring Control Circuit Terminals

‹ Control Circuit Wiring Precautions

Observe the following precautions when wiring control circuits.
• Separate control circuit wiring from main circuit wiring (terminals R/L1, S/L2, T/L3, B1, B2, U/T1, V/T2,
W/T3, , 1, 2, and 3) and other high-power lines.
• Separate wiring for control circuit terminals MA, MB, MC, M1, and M2 (contact outputs) from wiring to
other control circuit terminals.
• Use shielded twisted-pair cables for control circuits to prevent operating faults. Process cable ends as
shown in Fig 2.20.
• Connect the shield wire to terminal E (G).
• Insulate the shield with tape to prevent contact with other signal lines and equipment.
• Use a class 2 power supply (UL standard) when connecting to the control terminals.

Shield sheath Armor

Do not connect here.

Connect to shield sheath ter- Insulate with tape
minal at Inverter (terminal E
(G))

Fig 2.20 Processing the Ends of Shielded Twisted-pair Cables

2-29
 Wiring Check

‹ Checks
Check all wiring after wiring has been completed. Do not perform a buzzer check on control circuits. Perform
the following checks on the wiring.
• Is all wiring correct?
• Have any wire clippings, screws, or other foreign material been left?
• Are all screws tight?
• Are any wire ends contacting other terminals?

2-30
 Installing and Wiring Option Boards

Installing and Wiring Option Boards

‹ Option Board Models and Specifications

Up to three option boards can be mounted in the Inverter. You can mount up one Board into each of the three
places on the control board (A, C, and D) shown in Fig 2.21.
Table 2.14 lists the type of option boards and their specifications.

Table 2.14 Option Board Specifications

Mounting Loca-
Board Model Specifications
tion
PG-A2 Serial open-collector/complimentary inputs A
PG-B2 Phase A/B complimentary inputs A
PG Speed Control Boards
PG-D2 Single line-driver inputs A
PG-X2 Phase A/B line-driver inputs A
Input signal levels
0 to 10 V DC (20 kΩ), 1 channel
AI-14U C
4 to 20 mA (250 Ω), 1 channel
Input resolution: 14-bit
Input signal levels
Speed Reference Boards 0 to 10 V DC (20 kΩ)
AI-14B C
4 to 20 mA (250 Ω), 3 channels
Input resolution: 13-bit with sign bit
DI-08 8-bit digital speed reference setting C
DI-16H2 16-bit digital speed reference setting C
DeviceNet Communications
SI-N1 DeviceNet communications support C
Board
Profibus-DP Communica-
SI-P1 Profibus-DP communications support C
tions Board
CC-Link Communications
SI-C CC-Link communications support C
Board

LONWORKS SI-J
LONWORKS communications support C
Communications Board SI-W1
MECHATROLINK Commu-
SI-T MECHATROLINK communications support C
nication Board
AO-08 8-bit analog outputs, 2 channels D
Analog Monitor Board
AO-12 12-bit analog outputs, 2 channels D
DO-08 Six photocoupler outputs and 2 relay outputs D
Digital Output Board
DO-02C 2 relay outputs D

2-31
 ‹ Installation
Before mounting an option board, remove the terminal cover and be sure that the charge indicator inside the
Inverter is not lit. After confirming that the charge indicator is not lit, remove the Digital Operator and front
cover and then mount the option board.
The side of the front cover of the Inverter for 200/400 V Class 0.4 to 3.7 kW can be cut out as described in Fig
2.22 to make wiring of the option board easy. If the side of the front cover is cut out, the protective structure
will be open chassis (IEC IP00).
Refer to documentation provided with the option board for actual mounting instructions for option slots A, C,
and D.

„ Preventing C and D Option Board Connectors from Rising

After installing an option board into slot C or D, insert an option clip to prevent the side with the connector
from rising. The option clip can be easily removed by holding onto the protruding portion of the clip and pull-
ing it out.
Remove the option clip before installing an option board into slot C or D. The option board can not be
installed completely and may not function properly if it is installed with the option clip attached.

A option board mounting spacer hole

4CN
A option board connector
2CN
C option board connector

A option board mounting spacer

(Provided with A Option Board.)

C option board mounting spacer

C option board
Option Clip
(To prevent raising of
C and D option boards)
D option board
3CN
D option board connector D option board mounting spacer

A option board
A option board mounting spacer

Fig 2.21 Mounting Option Boards

Front Cover

Slit

Fig 2.22 Cutting the Front Cover

Cut out the slits on the front cover with nippers. Be careful to avoid injury.

2-32
 Installing and Wiring Option Boards

‹ PG Speed Control Board Terminals and Specifications

The terminal specifications for the PG Speed Control Boards are given in the following tables.

„PG-A2
The terminal specifications for the PG-A2 are given in the following table.

Table 2.15 PG-A2 Terminal Specifications

Terminal No. Contents Specifications
1 12 VDC (±5%), 200 mA max.
Power supply for pulse generator
2 0 VDC (GND for power supply)

3 Terminal for switching between12 V voltage input

+12 V/open collector switching ter-
and open collector input. For open collector input,
minal
4 short across 3 and 4.
TA1
H: +4 to 12 V; L: +1 V max. (Maximum response fre-
5
Pulse input terminal quency: 30 kHz)
6 Pulse input common
7 12 VDC (±10%), 20 mA max.
Pulse motor output terminal
8 Pulse monitor output common
TA2 (E) Shield connection terminal -

„PG-B2
The terminal specifications for the PG-B2 are given in the following table.

Table 2.16 PG-B2 Terminal Specifications

Terminal No. Contents Specifications
1 12 VDC (±5%), 200 mA max.
Power supply for pulse generator
2 0 VDC (GND for power supply)
H: +8 to 12 V
3 L: +1 V max.
A-phase pulse input terminal (Maximum response frequency: 30 kHz)
TA1
4 Pulse input common
H: +8 to 12 V
5 L: +1 V max.
B-phase pulse input terminal (Maximum response frequency: 30 kHz)
6 Pulse input common
1 Open collector output, 24 VDC, 30 mA max.
A-phase monitor output terminal
2 A-phase monitor output common
TA2
3 Open collector output, 24 VDC, 30 mA max.
B-phase monitor output terminal
4 B-phase monitor output common
TA3 (E) Shield connection terminal -

2-33
 „PG-D2
The terminal specifications for the PG-D2 are given in the following table.

Table 2.17 PG-D2 Terminal Specifications

Terminal No. Contents Specifications
1 12 VDC (±5%), 200 mA max.*
2 Power supply for pulse generator 0 VDC (GND for power supply)
3 5 VDC (±5%), 200 mA max.*
4 Pulse input + terminal Line driver input (RS-422 level input)
TA1
5 Pulse input - terminal Maximum response frequency: 300 kHz

6 Common terminal -
7 Pulse monitor output + terminal
Line driver output (RS-422 level output)
8 Pulse monitor output - terminal
TA2 (E) Shield connection terminal -
* 5 VDC and 12 VDC cannot be used at the same time.

„PG-X2
The terminal specifications for the PG-X2 are given in the following table.

Table 2.18 PG-X2 Terminal Specifications

Terminal No. Contents Specifications
1 12 VDC (±5%), 200 mA max.*
2 Power supply for pulse generator 0 VDC (GND for power supply)
3 5 VDC (±5%), 200 mA max.*
4 A-phase + input terminal
5 A-phase - input terminal
TA1
6 B-phase + input terminal Line driver input (RS-422 level input)
7 B-phase - input terminal Maximum response frequency: 300 kHz

8 Z-phase + input terminal

9 Z-phase - input terminal
10 Common terminal 0 VDC (GND for power supply)
1 A-phase + output terminal
2 A-phase - output terminal
3 B-phase + output terminal
Line driver output (RS-422 level output)
TA2 4 B-phase - output terminal
5 Z-phase + output terminal
6 Z-phase - output terminal
7 Control circuit common Control circuit GND
TA3 (E) Shield connection terminal -
* 5 VDC and 12 VDC cannot be used at the same time.

2-34
 Installing and Wiring Option Boards

‹ Wiring
Wiring examples are provided in the following illustrations for the option boards.

„ Wiring the PG-A2

Wiring examples are provided in the following illustrations for the PG-A2.

Three-phase, 200 Inverter

VAC (400 VAC)
R/L1 U/T1
S/L2 V/T2
T/L3 W/T3
PC-A2
+12 V power supply
1
0 V power supply
4CN 4CN 2
3
4 12 V voltage input (A/B phase)
TA1
5 Pulse 0 V
6
E E
7
TA2 (E) Pulse monitor output
8

Fig 2.23 Wiring a 12 V Voltage Input

Three-phase,
200 VAC (400 VAC) Inverter
R/L1 U/T1
S/L2 V/T2
T/L3 W/T3
PG-A2
+12 V power supply
1
2 0 V power supply
4CN 4CN
3 (Short circuit across
terminals 3-4)
4
TA1 Pulse input (+)
5
Pulse input (-)
6
E E
7
TA2 (E) Pulse monitor output
8

• Shielded twisted-pair wires must be used for signal lines.

• Do not use the pulse generator's power supply for anything other than the pulse generator (encoder).
Using it for another purpose can cause malfunctions due to noise.
• The length of the pulse generator's wiring must not be more than 100 meters.
Fig 2.24 Wiring an Open-collector Input

PG power
supply
+12 V
Pulse input

Short for
open-col-
lector
input

Pulse
monitor
output
Pulse
input

Fig 2.25 I/O Circuit Configuration of the PG-A2

2-35
 „ Wiring the PG-B2
Wiring examples are provided in the following illustrations for the PG-B2.

Inverter
Three-phase 200
VAC (400 VAC)

Power supply +12 V

Power supply 0 V
A-phase pulse output (+)
A-phase pulse output (-)
B-phase pulse output (+)
B-phase pulse output (-)

A-phase pulse monitor output

B-phase pulse monitor output

• Shielded twisted-pair wires must be used for signal lines.

• Do not use the pulse generator's power supply for anything other than the pulse generator (encoder).
Using it for another purpose can cause malfunctions due to noise.
• The length of the pulse generator's wiring must not be more than 100 meters.
• The direction of rotation of the PG can be set in user constant F1-05. The factory preset if for forward
rotation, A-phase advancement.

Fig 2.26 PG-B2 Wiring

PG power
supply +12 V

A-phase pulse
monitor output
Division rate circuit

A-phase
A-phase pulse pulses
input

B-phase pulse
monitor output
B-phase
B-phase pulse pulses
input

• When connecting to a voltage-output-type PG (encoder), select a PG that has an output impedance with
a current of at least 12 mA to the input circuit photocoupler (diode).
• The pulse monitor dividing ratio can be changed using constant F1-06 (PG division rate).

A-phase pulses
B-phase pulses

• The pulse monitor emitter is connected to common inside the PG-B2. The emitter common must be used
for external circuits.

Fig 2.27 I/O Circuit Configuration of the PG-B2

2-36
 Installing and Wiring Option Boards

„Wiring the PG-D2

Wiring examples are provided in the following illustrations for the PG-D2.

Three-phase 200 Inverter

VAC (400 VAC)

Power supply +12 V

Power supply 0 V
Power supply +5 V
Pulse input + (A/B phase)
Pulse input - (A/B phase)

Pulse monitor output

• Shielded twisted-pair wires must be used for signal lines.

• Do not use the pulse generator's power supply for anything other than the pulse generator (encoder).
Using it for another purpose can cause malfunctions due to noise.
• The length of the pulse generator's wiring must not be more than 100 meters.

Fig 2.28 PG-D2 Wiring

„Wiring the PG-X2

Wiring examples are provided in the following illustrations for the PG-X2.

Three-phase Inverter
200 VAC (400
VAC) R/L1 U/T1

S/L2 V/T2
T/L3 W/T3

Power supply +12 V

Power supply 0 V
Power supply +5 V
A-phase pulse input (+)
A-phase pulse input (-)
B-phase pulse input (+)
B-phase pulse input (-)

A-phase pulse monitor output

B-phase pulse monitor output

Z-phase pulse monitor output

• Shielded twisted-pair wires must be used for signal lines.

• Do not use the pulse generator's power supply for anything other than the pulse generator (encoder).
Using it for another purpose can cause malfunctions due to noise.
• The length of the pulse generator's wiring must not be more than 100 meters.
• The direction of rotation of the PG can be set in user constant F1-05 (PG Rotation). The factory preset if
for motor forward rotation, A-phase advancement.

Fig 2.29 PG-X2 Wiring

2-37
 ‹ Wiring Terminal Blocks
Use no more than 100 meters of wiring for PG (encoder) signal lines, and keep them separate from power
lines.
Use shielded, twisted-pair wires for pulse inputs and pulse output monitor wires, and connect the shield to the
shield connection terminal.

„Wire Sizes (Same for All Models)

Terminal wire sizes are shown in Table 2.19.

Table 2.19 Wire Sizes

Terminal
Terminal
Screws Wire Thickness (mm2) Wire Type

Pulse generator power supply • Shielded, twisted-pair wire

Stranded wire: 0.5 to 1.25
Pulse input terminal - • Shielded, polyethylene-covered, vinyl
Single wire: 0.5 to 1.25
Pulse monitor output terminal sheath cable
(KPEV-S by Hitachi Electric Wire or
Shield connection terminal M3.5 0.5 to 2 equivalent)

„Straight Solderless Terminals for Control Circuit Terminals

We recommend using straight solderless terminal on signal lines to simplify wiring and improve reliability.
Refer to Straight Solderless Terminal Sizes for specifications.

„Closed-loop Connector Sizes and Tightening Torque

The closed-loop connectors and tightening torques for various wire sizes are shown in Table 2.20.

Table 2.20 Closed-loop Connectors and Tightening Torques

Terminal
Wire Thickness [mm2] Crimp Terminal Size Tightening Torque (N • m)
Screws
0.5 1.25 - 3.5
0.75 1.25 - 3.5
M3.5 0.8
1.25 1.25 - 3.5
2 2 - 3.5

„Wiring Method and Precautions

The wiring method is the same as the one used for straight solderless terminals. Refer to page 2-23. Observe
the following precautions when wiring.
• Separate the control signal lines for the PG Speed Control Board from main circuit lines and power lines.
• Connect the shield when connecting to a PG. The shield must be connected to prevent operational errors
caused by noise. Also, do not use any lines that are more than 100 m long. Refer to Fig 2.20 for details on
connecting the shield.
• Connect the shield to the shield terminal (E).
• Do not solder the ends of wires. Doing so may cause contact faults.
• When not using straight solderless terminals, strip the wires to a length of approximately 5.5 mm.

2-38
 Installing and Wiring Option Boards

‹ Selecting the Number of PG (Encoder) Pulses

The setting for the number of PG pulses depends on the model of PG Speed Control Board being used. Set the
correct number for your model.

„PG-A2/PG-B2
The maximum response frequency is 32,767 Hz.
Use a PG that outputs a maximum frequency of approximately 20 kHz for the rotational speed of the motor.

Motor speed at maximum frequency output (min−1)

× PG rating (p/rev) = 20,000 Hz
60

Some examples of PG output frequency (number of pulses) for the maximum frequency output are shown in
Table 2.21.

Table 2.21 PG Pulse Selection Examples

PG Rating PG Output Frequency for Maximum Fre-
Motor's Maximum Speed (min−1) (p/rev) quency Output (Hz)
1800 600 18,000
1500 600 15,000
1200 900 18,000
900 1200 18,000
Note 1. The motor speed at maximum frequency output is expressed as the sync rotation speed.
2. The PG power supply is 12 V.
3. A separate power supply is required if the PG power supply capacity is greater than 200 mA. (If momentary power loss must be handled, use a
backup capacitor or other method.)

PG power supply

Capacitor for momentary

power loss

Signals

Fig 2.30 PG-B2 Connection Example

2-39
 „PG-D2/PG-X2
There are 5 V and 12 V PG power supplies.
Check the PG power supply specifications before connecting.
The maximum response frequency is 300 kHz.
Use the following equation to computer the output frequency of the PG (fPG).

Motor speed at maximum frequency output (min−1)

fPG (Hz) = × PG rating (p/rev)
60

A separate power supply is required if the PG power supply capacity is greater than 200 mA. (If momentary
power loss must be handled, use a backup capacitor or other method.)

PG-X2
PG power
supply
TA1
AC
0V +12V
IP12 1
0V
IG 2
Capacitor for +12 V
IP5 3 momentary
power loss + +
A (+) 4
- PG
A (-) 5
+
B (+) 6
-
B (-) 7
Z (+) 8
Z (-) 9
IG 10

TA3

Fig 2.31 PG-X2 Connection Example (for 12 V PG power supply)

2-40
Digital Operator and Modes
This chapter describes Digital Operator displays and functions, and provides an overview of
operating modes and switching between modes.

Digital Operator............................................................3-2
Modes ..........................................................................3-5
 Digital Operator
This section describes the displays and functions of the Digital Operator.

‹ Digital Operator Display

The key names and functions of the Digital Operator are described below.

Drive Mode Indicators (LED)

FWD: Lit when there is a Forward Run Command input.
REV: Lit when there is a Reverse Run Command input.
SEQ: Lit when the Run Command from the control
circuit terminal is enabled.
REF: Lit when the frequency reference from control
circuit terminals A1 and A2 is enabled.
ALARM: Lit when error activated.
Blinks when alarm activated.
Data Display
Displays monitor data, constant numbers, and settings.

Mode Display (Displayed at upper left of data display.)

DRIVE: Lit in Drive Mode.
QUICK: Lit in Quick Programming Mode.
ADV: Lit in Advanced Programming Mode.
VERIFY: Lit in Verify Mode.
A. TUNE: Lit in Autotuning Mode.

Keys

Execute operations such as setting user constants,

monitoring, jogging, and autotuning.

Fig 3.1 Digital Operator Component Names and Functions

‹ Digital Operator Keys

The names and functions of the Digital Operator Keys are described in Table 3.1.

Table 3.1 Key Functions

Key Name Function
Switches between operation via the Digital Operator (LOCAL) and
LOCAL/REMOTE Key control circuit terminal operation (REMOTE).
This Key can be enabled or disabled by setting user constant o2-01.

MENU Key Selects menu items (modes).

ESC Key Returns to the status before the DATA/ENTER Key was pressed.

Enables jog operation when the Inverter is being operated from the
JOG Key
Digital Operator.

3-2
 Digital Operator

Table 3.1 Key Functions (Continued)

Key Name Function

Selects the rotation direction of the motor when the Inverter is being
FWD/REV Key
operated from the Digital Operator.

Sets the number of digits for user constant settings.

Shift/RESET Key
Also acts as the Reset Key when a fault has occurred.

Selects menu items, sets user constant numbers, and increments set
Increment Key values.
Used to move to the next item or data.
Selects menu items, sets user constant numbers, and decrements set
Decrement Key values.
Used to move to the previous item or data.
Pressed to enter menu items, user constants, and set values.
DATA/ENTER Key Also used to switch from one display to another.
Constants cannot be changed when Undervoltage (UV) is detected.

Starts the Inverter operation when the Inverter is being controlled by

RUN Key
the Digital Operator.

Stops Inverter operation.

STOP Key This Key can be enabled or disabled when operating from the control
circuit terminal by setting user constant o2-02.
Note Except in diagrams, Keys are referred to using the Key names listed in the above table.

There are indicators on the upper left of the RUN and STOP Keys on the Digital Operator. These indicators
will light and flash to indicate operating status.
The RUN Key indicator will flash and the STOP Key indicator will light during initial excitation of the
dynamic brake. The relationship between the indicators on the RUN and STOP Keys and the Inverter status is
shown in the Fig 3.2.

Inverter output frequency

RUN STOP
STOP
Frequency setting

RUN
STOP
Lit Blinking Not lit

Fig 3.2 RUN and STOP Indicators

3-3
 The following table shows the relationship between the indicators on the RUN and STOP Keys and the
Inverter conditions.
The indicators are lit, unlit or blinking reflecting the order of priority.

Table 3.2 Relation of Inverter to RUN and STOP Indicators

RUN STOP Inverter
Priority Conditions
Indicator Indicator Status
1 Stopped Power supply is shut down.
Emergency stop
• Stop Command is sent from the Digital Operator when the control cir-
cuit terminals were used to operate the Inverter.
• Emergency Stop Command is sent from the control circuit terminal.
2 Stopped* Switched from LOCAL (operation using the Digital Operator) to
REMOTE (operation using the control circuit terminals) when the Run
Command is sent from the external terminal.
Switched from the Quick or Advanced Quick programming mode to the
Drive mode when the Run Command is sent from the external terminal.
The Inverter is run at a frequency below the minimum output frequency.
3 Stopped The Run Command is carried out when the External Baseblock Com-
mand using the multi-function contact input terminal is issued.

4 Stopped Stopped

During deceleration to a stop

During DC injection braking when using the multi-function contact input
5 Running terminal.
During initial excitation of DC injection braking while the Inverter is
stopped.
During emergency deceleration
• Stop Command is sent from the Digital Operator when operating the
6 Running
Inverter using the control circuit terminals.
• Emergency Stop Command is sent from the control circuit terminal.
Run Command is issued.
7 Running During initial excitation of DC injection braking when starting the
Inverter.

Note : Lit : Blinking : Not lit

* If planning to run the Inverter again, first turn OFF the Run Command and Emergency Stop Command from the control circuit terminal and send the Run
Command.

3-4
 Modes

Modes
This section describes the Inverter's modes and switching between modes.

‹ Inverter Modes
The Inverter's user constants and monitoring functions are organized in groups called modes that make it eas-
ier to read and set user constants.The Inverter is equipped with 5 modes.
The 5 modes and their primary functions are shown in the Table 3.3.

Table 3.3 Modes

Mode Primary function(s)
The Inverter can be run in this mode.
Drive mode Use this mode when monitoring values such as frequency references or output cur-
rent, displaying fault information, or displaying the fault history.
Use this mode to reference and set the minimum user constants to operate the
Quick programming mode
Inverter (e.g., the operating environment of the Inverter and Digital Operator).
Advanced programming mode Use this mode to reference and set all user constants.
Use this mode to read/set user constants that have been changed from their factory-
Verify mode
set values.
Use this mode when running a motor with unknown motor constants in the vector
Autotuning mode* control method. The motor constants are calculated and set automatically.
This mode can also be used to measure only the motor line-to-line resistance.
* Always perform autotuning with the motor before operating using vector control. Autotuning mode will not be displayed during operation or when an error
has occurred. The default setting of the Inverter is for open-loop vector 1 control (A1-02 = 2).

3-5
 ‹ Switching Modes
The mode selection display will appear when the MENU Key is pressed from a monitor or setting display.
Press the MENU Key from the mode selection display to switch between the modes.
Press the DATA/ENTER Key from the mode selection key to monitor data and from a monitor display to
access the setting display.

Display at Startup
'5,9( 5G\
乥⥛ᣛҸ
8 +]

0(18
Mode Selection
Display Monitor Display Setting Display
'$7$ '$7$
(17(5 (17(5
˚ '$7$
5(6(7 (17(5
'5,9( '5,9( 5G\ '5,9( 5G\ '5,9( 5G\
偅ࡼ῵ᓣ ⲥ㾚 乥⥛ᣛҸ 乥⥛ᣛҸ

* *
* 8 +] 8  +] 8 +]
(6& (6& (6&
0(18

'$7$
(17(5 '$7$
48,&. 48,&. (17(5 48,&.
ㅔᯧ⿟ᑣ῵ᓣ ᥻ࠊ῵ᓣ䗝ᢽ ᮴3*ⶶ䞣᥻ࠊ

* *
* $   $   
(6& (6&
0(18
'$7$
(17(5
'$7$ ˚ '$7$
(17(5 5(6(7 (17(5
$'9 $'9 $'9 $'9
催㑻⿟ᑣ῵ᓣ ⦃๗䆒ᅮ ᭛ᄫ䗝ᢽ Ё᭛

* *
* $  $     $    
(6& (6& (6&
0(18

'$7$
9(5,)<
(17(5
9(5,)< The constant number will be displayed if a
᷵偠῵ᓣ ᮴ব᳈ constant has been changed. Press the
DATA/ENTER Key to enable the change.
* *
*
(6&
0(18

'$7$
(17(5 '$7$
$781( $781( (17(5 $781(
㞾ᄺд῵ᓣ 䗝ᢽ㞾ᄺд῵ᓣ ᮟ䕀ᔶ㞾ᄺд
* *
* 7    7    
(6& (6&

Fig 3.3 Mode Transitions

When running the Inverter after using Digital Operator, press the MENU Key to select the drive mode (dis-
played on the LCD screen) and then press the DATA/ENTER Key from the drive mode display to bring up the
monitor display. Run Commands can't be received from any other display. (Monitor display in the drive mode
IMPORTANT will appear when the power is turned ON.)

3-6
 Modes

‹ Drive Mode
Drive mode is the mode in which the Inverter can be operated. The following monitor displays are possible in
drive mode: The frequency reference, output frequency, output current, and output voltage, as well as fault
information and the fault history.
When b1-01 (Reference selection) is set to 0, the frequency can be changed from the frequency setting display.
Use the Increment, Decrement, and Shift/RESET Keys to change the frequency. The user constant will be
written and the monitor display will be returned to when the DATA/ENTER Key is pressed after changing the
setting.
„Example Operations
Key operations in drive mode are shown in the following figure.
Display at Startup
'5,9( 5G\
乥⥛ᣛҸ
8 +]

0(18
'$7$
Mode Selection Monitor Display (17(5 Frequency Setting Display
Display
'$7$
(17(5
$ %  
'$7$
˚ (17(5
'5,9( '5,9( 5G\ 5(6(7 '5,9( 5G\ '5,9( 5G\

偅ࡼ῵ᓣ ⲥ㾚 乥⥛ᣛҸ 乥⥛ᣛҸ

* *
* 8  +] 8  +] 8  +]
(6&
(6&
0(18 (6&

'5,9( 5G\ ˚ '5,9( 5G\

The Frequency Setting
5(6(7
48,&.
ⲥ㾚 䕧ߎ乥⥛ Display will not be
ㅔᯧ⿟ᑣ῵ᓣ displayed when using an
8  +] 8  +]
*** (6&
analog reference.
0(18
˚
'5,9( 5G\ 5(6(7 '5,9( 5G\

$'9 ⲥ㾚 ዄֱؐᣕ䕧ߎ乥⥛
催㑻⿟ᑣ῵ᓣ 8 
 +] 8  +]
* (6&
* *
 
0(18
'$7$
(17(5  
9(5,)<
˚
5(6(7
The fault name will be
᷵偠῵ᓣ '5,9( 5G\ '5,9( 5G\
displayed if the DATA/ENTER
* ᬙ䱰䎳䏾 ᔧࠡᬙ䱰
* * Key is pressed while a constant
8  8  is being displayed for which a
0(18
(6& fault code is being displayed.
˚
$781( 5(6(7 '$7$
'5,9( 5G\ '5,9( 5G\ (17(5 '5,9( 5G\
㞾ᄺд῵ᓣ
ᬙ䱰䎳䏾 䖛এᬙ䱰 Џಲ䏃䖛⬉य़
*
* * 8  29 8  29 8  29
(6& (6&

 

'$7$
  (17(5

˚ '$7$
5(6(7 (17(5
'5,9( '5,9( '5,9(
ᬙ䱰䆄ᔩ ⃵ࠡᬙ䱰 䕧ߎ䖛⬉⌕
8 2& 8   2& 8  2&
(6& (6&

˚
5(6(7 '$7$
5G\ (17(5 '5,9( 5G\
'5,9( '5,9( 5G\
ᬙ䱰䆄ᔩ ⃵ࠡᬙ䱰 Џಲ䏃䖛⬉य़
8  29 8  29 8  29
(6& (6&

 
$ %

Fig 3.4 Operations in Drive Mode

3-7
 Note When changing the display with the Increment and Decrement Keys, the next display after the one for the last parameter number will be the one for the
first parameter number and vise versa. For example, the next display after the one for U1-01 will be U1-40. This is indicated in the figures by the letters
A and B and the numbers 1 to 6.

The display for the first monitor constant (frequency reference) will be displayed when power is turned ON.
The monitor item displayed at startup can be set in o1-02 (Monitor Selection after Power Up).
Operation cannot be started from the mode selection display.
IMPORTANT

‹ Quick Programming Mode

In quick programming mode, the constants required for Inverter trial operation can be monitored and set.
Constants can be changed from the setting displays. Use the Increment, Decrement, and Shift/RESET Keys to
change the frequency. The user constant will be written and the monitor display will be returned to when the
DATA/ENTER Key is pressed after changing the setting.
Refer to Chapter 5 User Constants for details on the constants displayed in quick programming mode.

„Example Operations
Key operations in quick programming mode are shown in the following figure.

3-8
 Modes

Mode Selection Display Monitor Display Frequency Setting Display

0(18

'5,9(
偅ࡼ῵ᓣ
*
* *
$ %
0(18

'$7$
(17(5 '$7$
48,&. 48,&. (17(5 48,&.

ㅔᯧ⿟ᑣ῵ᓣ ᥻ࠊ῵ᓣ䗝ᢽ ᮴3*ⶶ䞣᥻ࠊ

* $   $    
* * (6&
(6&
0(18
'$7$
48,&. (17(5 48,&.
乥⥛ᣛҸ䗝ᢽ ᥻ࠊಲ䏃ッᄤ
$'9
催㑻⿟ᑣ῵ᓣ E   E    
(6&
*
* *
'$7$
48,&. (17(5 48,&.
0(18
䖤㸠ᣛҸ䗝ᢽ ᥻ࠊಲ䏃ッᄤ

9(5,)<
E   E    
(6&
᷵偠῵ᓣ
*
* *
'$7$
48,&. (17(5 48,&.
0(18
ッᄤ$0๲Ⲟ ッᄤ$0๲Ⲟ
+  +  
$781(
(6&
㞾ᄺд῵ᓣ
* '$7$
* * 48,&. (17(5 48,&.
⬉ᴎֱᡸࡳ㛑䗝ᢽ 䗮⫼⬉ᴎ
/   /    
(6&

'$7$
48,&. (17(5 48,&.
‫ޣ‬䗳䰆ℶ༅䗳䗝ᢽ ᳝ᬜ
/   /   
(6&

$ %

Fig 3.5 Operations in Quick Programming Mode

3-9
 ‹ Advanced Programming Mode
In advanced programming mode, all Inverter constants can be monitored and set.
Constants can be changed from the setting displays. Use the Increment, Decrement, and Shift/RESET Keys to
change the frequency. The user constant will be written and the monitor display will be returned to when the
DATA/ENTER Key is pressed after changing the setting.
Refer to Chapter 5 User Constants for details on the constants.

„Example Operations
Key operations in advanced programming mode are shown in the following figure.

Mode Selection Display Monitor Display Setting Display

$ %  
'$7$
(17(5
'$7$ ˚
(17(5 5(6(7
$'9 $'9 $'9 $'9
催㑻⿟ᑣ῵ᓣ ⦃๗䆒ᅮ ᭛ᄫ䗝ᢽ Ё᭛

* *
* $   $    $   
(6& (6& (6&
0(18
'$7$
˚ (17(5
5(6(7
$'9 $'9 $'9
9(5,)< ⦃๗䆒ᅮ ᥻ࠊ῵ᓣ䗝ᢽ ᮴3*ⶶ䞣᥻ࠊ
᷵偠῵ᓣ
$   $   
(6&
$   
*
* * (6&

0(18  

$781(
 
㞾ᄺд῵ᓣ ˚
'$7$
(17(5
5(6(7
* $'9 $'9 $'9
* * 3,'᥻ࠊ 3,'᥻ࠊ䗝ᢽ 3,'᮴ᬜ
0(18 E   E    E   
(6&
(6&
'5,9(
˚ '$7$
偅ࡼ῵ᓣ $'9
5(6(7
$'9 (17(5 $'9
* 3,'᥻ࠊ
* * ড作ϻ༅Ẕߎᯊ䯈 ড作ϻ༅Ẕߎᯊ䯈
E  VHF E  VHF E VHF
0(18 (6&
(6&

48,&.
 
ㅔᯧ⿟ᑣ῵ᓣ
*
 
* * '$7$
˚ (17(5
0(18 5(6(7 $'9 $'9
$'9
䕀ⶽᵕ䰤 ℷ䕀⬉ࡼ䕀ⶽᵕ䰤 ℷ䕀⬉ࡼ䕀ⶽᵕ䰤
/   /    /  
(6& (6&

˚ '$7$
5(6(7 (17(5
$'9 $'9 $'9
䕀ⶽᵕ䰤 ড䕀‫⫳ݡ‬䕀ⶽᵕ䰤 ড䕀‫⫳ݡ‬䕀ⶽᵕ䰤
/   /    /  
(6&
(6&

 
$ %

Fig 3.6 Operations in Advanced Programming Mode

3-10
 Modes

„Setting User Constants

Here, the procedure is shown to change C1-01 (Acceleration Time 1) from 10 s to 20 s.

Table 3.4 Setting User Constants in Advanced Programming Mode

Step
Digital Operator Display Description
No.

1 Power supply turned ON.

2 MENU Key pressed to enter drive mode.

* *

3 MENU Key pressed to enter quick programming mode.

* *

4 MENU Key pressed to enter advanced programming mode.

* *

5 DATA/ENTER pressed to access monitor display.

6 Increment or Decrement Key pressed to display C1-01 (Acceleration Time 1).

DATA/ENTER Key pressed to access setting display. The setting of C1-01

7
(10.00) is displayed.

8 Shift/RESET Key pressed to move the flashing digit to the right.

9 Increment Key pressed to change set value to 20.00 s.

10 DATA/ENTER Key pressed to enter the set data.

“ 写入完毕 ” is displayed for 1.0 s after the data setting has been confirmed
11
with the DATA/ENTER Key.

12 The monitor display for C1-01 returns.

3-11
 „External Fault Setting Procedure
Examples of the Digital Operator displays that appear when setting an eternal error for a multi-function con-
tact input in Advanced Programming Mode are shown in the following diagram.

Mode Selection Display Monitor Display Setting Display

$ %    
'$7$ '$7$
(17(5 (17(5
'$7$ ˚
(17(5 5(6(7
$'9 $'9 $'9 $'9
催㑻⿟ᑣ῵ᓣ ᭄ᄫ䕧ܹ ッᄤ6ࡳ㛑䆒ᅮ $ᐌᯊ㞾⬅䖤㸠

* *
* +   +    +    
(6& (6& (6&
0(18

˚
5(6(7 $'9
$'9 $'9
9(5,)< ッᄤ6䆒ᅮ
᭄ᄫ䕧ܹ %ᐌᯊ㞾⬅䖤㸠
᷵偠῵ᓣ
*
+   +    +   
* * (6&

0(18 ˚
5(6(7 $'9
$'9 $'9

$781(
᭄ᄫ䕧ܹ ッᄤ6䆒ᅮ $䖤㸠Ё㞾⬅䖤㸠
㞾ᄺд῵ᓣ +  +    +   
* (6&
* *
0(18
$'9
  %䖤㸠Ё㞾⬅䖤㸠
'5,9( $'9
+   
偅ࡼ῵ᓣ ᭄ᄫ䕧ߎ
* +  
* *
0(18

$'9
48,&.
㛝‫ކ‬䕧ܹ䕧ߎ䆒ᅮ
ㅔᯧ⿟ᑣ῵ᓣ
* +  
* * $'9
0(18
%䖤㸠Ёা᡹䄺
$ % +  ) 

 

Fig 3.7 External Fault Function Setting Example

3-12
 Modes

‹ Verify Mode
Verify mode is used to display any constants that have been changed from their default settings in a program-
ming mode or by autotuning. “ 无变更 ” will be displayed if no settings have been changed.
Of the environment mode settings, only A1-02 will be displayed if it has been changed. Other environment
modes settings will not be displayed even if they have been changed from their default settings.
Even in verify mode, the same procedures can be used to change settings as are used in the programming
modes. Use the Increment, Decrement, and Shift/RESET Keys to change the frequency. The user constant will
be written and the monitor display will be returned to when the DATA/ENTER Key is pressed after changing
the setting.

„Example Operations
An example of key operations is given below for when the following settings have been changed from their
default settings: b1-01 (Reference Selection), C1-01 (Acceleration Time 1), E1-01 (Input Voltage Setting), and
E2-01 (Motor Rated Current).

Mode Selection Display Monitor Display Setting Display

'$7$
(17(5

$'9
催㑻⿟ᑣ῵ᓣ

***
$ %
0(18

'$7$
(17(5 '$7$
9(5,)< 9(5,)< (17(5 9(5,)<
᷵偠῵ᓣ 乥⥛ᣛҸ䗝ᢽ
᪡԰఼
* E 
* * 
E   
(6&
(6&
0(18
'$7$
9(5,)< (17(5 9(5,)<

$781( ࡴ䗳ᯊ䯈 ࡴ䗳ᯊ䯈

㞾ᄺд῵ᓣ & VHF &  VHF
* (6&
* *
'$7$
0(18 9(5,)< (17(5 9(5,)<

䕧ܹ⬉य़ 䕧ܹ⬉य़

'5,9( ( 9$& (   9$&

(6&
偅ࡼ῵ᓣ
*
* * 9(5,)<
'$7$
(17(5 9(5,)<
⬉ᴎ乱ᅮ⬉⌕ ⬉ᴎ乱ᅮ⬉⌕
0(18
( $ (  $
(6&
48,&.
ㅔᯧ⿟ᑣ῵ᓣ
$ %
***
0(18

Fig 3.8 Operations in Verify Mode

3-13
 ‹ Autotuning Mode

Autotuning automatically tunes and sets the required motor constants when operating in the vector control
methods. Always perform autotuning before starting operation.
When V/f control has been selected, stationary autotuning for only line-to-line resistance can be selected.
When the motor cannot be disconnected from the load, perform stationary autotuning. Contact your Yaskawa
representatives to set motor constants by calculation.
The Inverter's autotuning function automatically determines the motor constants, while a servo system's auto-
tuning function determines the size of a load, so these autotuning functions are fundamentally different. The
default setting of the Inverter is for open-loop vector 1 control.

„Example of Operation
Set the motor output power (in kW), rated voltage, rated current, rated frequency, rated speed, and number of
poles specified on the nameplate on the motor and then press the RUN Key. The motor is automatically run
and the motor constants measured based on these settings and autotuning will be set.
Always set the above items. Autotuning cannot be started otherwise, e.g., it cannot be started from the motor
rated voltage display.
Constants can be changed from the setting displays. Use the Increment, Decrement, and Shift/RESET Keys to
change the frequency. The user constant will be written and the monitor display will be returned to when the
DATA/ENTER Key is pressed after changing the setting.
The following example shows autotuning for open-loop vector control while operating the motor without
switching to motor 2.

3-14
 Modes

Mode Selection Display Monitor Display Setting Display

'$7$
(17(5

9(5,)<
᷵偠῵ᓣ

***
$
0(18

'$7$
(17(5 '$7$
$781( $781( (17(5 $781(
㞾ᄺд῵ᓣ 䗝ᢽ㞾ᄺд῵ᓣ ᮟ䕀ᔶ㞾ᄺд

* *
* 7   7  
(6& (6&
0(18
'$7$
$781( (17(5 $781(

'5,9(
⬉ᴎ෎ᴀ乥⥛ ⬉ᴎ෎ᴀ乥⥛
偅ࡼ῵ᓣ 7 +] 7  +]


* *
* (6&

'$7$
0(18 $781( (17(5 $781(
⬉ᴎᵕ᭄ ⬉ᴎᵕ᭄
7 
48,&.
(6&
ㅔᯧ⿟ᑣ῵ᓣ

$781( 5G\ 581 $781( 5G\ $781( 5G\

㞾ᄺд 㞾ᄺд䖤㸠Ё 㞾ᄺд䖤㸠Ё
0(18
+] $ +]$ +]$

$'9 6723
催㑻⿟ᑣ῵ᓣ The display will
$ automatically
* *
* change depending
$781(
㞾ᄺдЁℶ
$781(
㞾ᄺдᅠ↩
0(18 on the status of 䕧ܹњ 6723 䬂
autotuning.

* TUn10 will be displayed during rotational autotuning and TUn11 will be displayed during stationary autotuning. The DRIVE indicator will light when
autotuning starts.

Fig 3.9 Operation in Autotuning Mode

The setting displays in for autotuning depend on the control method (V/f, V/f with PG, or open-loop vector). If
a fault occurs during autotuning, refer to Chapter 7 Troubleshooting.

IMPORTANT

3-15
 Trial Operation
This chapter describes the procedures for trial operation of the Inverter and provides an example
of trial operation.

Overview of Trial Operation Procedure........................4-2

Trial Operation Procedures..........................................4-3
Adjustment Suggestions ............................................4-18
 Overview of Trial Operation Procedure
Perform trial operation according to the following flowchart.

START

Installation

Wiring

Set power supply voltage.*1

Turn ON power.

Confirm status.
Select
Basic settings
operating
(Quick programming mode)
method.
Vector (A1-02=2, 3, or 4)*5
V/f control?
V/f YES V/f with PG
(Default: A1-02=0) (A1-02=1)
PG?

Set E1-03. Set E1-03, E2-04, and F1-01.*2

V/f default: 200V/50Hz(400V/50Hz) V/f default: 200V/50Hz
(400V/50Hz)
Settings according
to control mode
Load is
Motor cable over OK to operate *3 NO
50 m or heavy load possibly YES connected to motor when YES
causing motor to stall or motor during operating motor first time
overload? autotuning? after autotuning?

YES NO
NO Stationary autotuning for *4 Rotational Stationary Stationary
line-to-line resistance only autotuning autotuning 1 *6 autotuning 2 *6

Application settings
(Advanced programming mode)
*1 Set for 400 V Class Inverter for 55 kW or more.
No-load operation
*2 If there is a reduction gear between the motor and PG, set
the reduction ratio in F1-12 and F1-13 in advanced
Loaded operation programming mode.

Optimum adjustments and *3 Use rotational autotuning to increase autotuning accuracy

constant settings whenever it is okay for the motor to be operated.

Check/record constants. *4 If the motor cable changes to 50 m or longer for the actual
installation, perform stationary autotuning for the line-to-line
resistance only on-site.
END
*5 The default control mode is open-loop vector control 2
(A1-02 =2).

*6 If the maximum output frequency is different from the base

frequency, set the maximum output frequency (E1-04)
after autotuning.

Fig 4.1 Trial Operation Flowchart

4-2
 Trial Operation Procedures

Trial Operation Procedures

The procedure for the trial operate is described in order in this section.

‹ Setting the Power Supply Voltage Jumper (400 V Class Inverters of 55 kW

or Higher)
Set the power supply voltage jumper after setting E1-01 (Input Voltage Setting) for 400 V Class Inverters
of 55 kW or higher. Insert the jumper into the power tap nearest to the actual power supply
voltage. If the wrong jumper is selected, the Inverter may be damaged.
The jumper is factory-set to 400/415 V when shipped. If the power supply voltage is not 400/415 V, use the
following procedure to change the setting.
1. Turn OFF the power supply and wait for at least 5 minutes.
2. Confirm that the CHARGE indicator has gone out.
3. Remove the terminal cover.
4. Insert the jumper at the position for the voltage supplied to the Inverter (see Fig 4.2).
5. Return the terminal cover to its original position.

Power tap

200 V Class power supply

400 V class power supply Jumper (factory-set position)
Power supply input terminals
CHARGE indicator

Fig 4.2 Power Supply Voltage Jumper

‹ Power ON
Confirm all of the following items and then turn ON the power supply.
• Check that the power supply is of the correct voltage.
200 V Class: 3-phase 200 to 240 VDC, 50/60 Hz
400 V Class: 3-phase 380 to 480 VDC, 50/60 Hz
• Make sure that the motor output terminals (U, V, W) and the motor are connected correctly.
• Make sure that the Inverter control circuit terminal and the control device are wired correctly.
• Set all Inverter control circuit terminals to OFF.
• When using a PG Speed Control Board, make sure that it is wired correctly.
• Make sure that the motor is not connected to the mechanical system (no-load status)

4-3
 ‹ Checking the Display Status
If the Digital Operator's display at the time the power is connected is normal, it will read as follows:

'5,9( 5G\
Display for normal operation 乥⥛ᣛҸ The frequency reference monitor is dis-
played in the data display section.
8 +]

When an fault has occurred, the details of the fault will be displayed instead of the above display. In that case,
refer to Chapter 7 Troubleshooting. The following display is an example of a display for faulty operation.

'5,9( 
The display will differ depending on the
Display for fault operation 89 type of fault.
Џಲ䏃⃴⬉य़ A low voltage alarm is shown at left.

4-4
 Trial Operation Procedures

‹ Basic Settings
Switch to the quick programming mode (“QUICK” will be displayed on the LCD screen) and then set the fol-
lowing user constants. Refer to Chapter 3 Digital Operator and Modes for Digital Operator operating proce-
dures and to Chapter 5 User Constants and Chapter 6 Constant Settings by Function for details on the user
constants.
Constants that must be set are listed in Table 4.1 and those that are set according to the application are listed in
Table 4.2.
Table 4.1 Constants that Must Be Set
Con-
Setting Factory
stant Name Description Page
Range Setting
Number
Set the control method for the Inverter.
0: V/f control
Control method 1: V/f control with PG
A1-02 0 to 4 2 5-8
selection 2: Open-loop vector 1 control
3: Flux vector
4: Open-loop vector 2 control
Set the frequency reference input method.
0: Digital Operator 5-10
Reference selec- 1: Control circuit terminal (analog input) 6-2
b1-01 0 to 4 1
tion 2: MEMOBUS communications 6-76
3: Option board 6-94
4: Pulse train input
Set the Run Command input method.
5-10
0: Digital Operator
Operation 6-10
b1-02 1: Control circuit terminal (sequence input) 0 to 3 1
method selection 6-76
2: MEMOBUS communications
6-94
3: Option board
Acceleration time Set the acceleration time in seconds for the output 5-21
C1-01 0.0 to 6000.0 10.0 s
1 frequency to climb from 0% to 100%. 6-18
Deceleration time Set the deceleration time in seconds for the output 5-21
C1-02 0.0 to 6000.0 10.0 s
1 frequency to fall from 100% to 0%. 6-18
200 V
155 to 255 V (200 V
Set the Inverter's nominal input voltage in volts.
Input voltage set- (200 V Class) Class) 5-33
E1-01 This setting is used as a reference value in protec-
ting 310 to 510 V 400 V 6-120
tion functions.
(400 V Class) (400 V
Class)
Setting for
general-
10% to 200% purpose 5-34
Motor rated cur-
E2-01 Set the motor rated current. of Inverter's motor of 6-57
rent
rated current same 6-117
capacity
as Inverter
Set to enable or disable the motor overload protec-
tion function using the electronic thermal relay.
Motor protection 0: Disabled 5-57
L1-01 0 to 3 1
selection 1: General motor protection 6-57
2: Inverter motor protection
3: Vector motor protection

4-5
 Table 4.2 Constants that Are Set as Required
Con-
Setting Factory
stant Name Description Page
Range Setting
Number
Select stopping method when Stop Command is
sent.
Stopping method 0: Deceleration to stop 5-10
b1-03 0 to 3 0
selection 1: Coast to stop 6-12
2: DC braking stop
3: Coast to stop with timer
Depends
on capac-
Carrier fre- ity, volt-
C6-02 1 to F 5-26
quency selection age, and
The carrier frequency is set low if the motor cable control
is 50 m or longer or to reduce radio noise or leak- method.
age current.
Carrier fre-
Depends
quency selection
C6-11 1 to 4 on kVA 5-26
for open-loop
setting.
vector 2 control

d1-01 to
Frequency refer-
d1-01 to d1-04:
ences 1 to 4 and Set the required speed references for multi-step
d1-04 and 0 to 400.00 Hz 0.00 Hz 5-27
jog frequency ref- speed operation or jogging.
d1-17 d1-17:
erence
6.00 Hz
Set the voltage level gain for the multi-function H4-02:
H4-02
FM and AM ter- analog output 1 (H4-02) and 2 (H4-05). 1.00
and H4- 0.00 to 2.50 5-53
minal output gain Set the number of multiples of 10 V to be output as H4-05:
05
the 100% output for the monitor item. 0.50
0: Disabled (Deceleration as set. If deceleration
time is too short, a main circuit overvoltage
may result.)
1: Enabled (Deceleration is stopped when the
main circuit voltage exceeds the overvoltage
level. Deceleration restarts when voltage is
Stall prevention returned.)
5-60
L3-04 selection during 2: Intelligent deceleration mode (Deceleration 0 to 3 1
6-25
deceleration rate is automatically adjusted so that the
Inverter can decelerate in the shortest possible
time. Set deceleration time is disregarded.)
3: Enabled (with Braking Resistor Unit)
When a braking option (Braking Resistor, Braking
Resistor Unit, Braking Unit) is used, always set to
0 or 3.

4-6
 Trial Operation Procedures

‹ Settings for the Control Methods

Autotuning methods depend on the control method set for the Inverter. Make the settings required by the con-
trol method.

„Overview of Settings
Make the required settings in quick programming mode and autotuning mode according to the following flow-
chart.

START

NO
Vector control (A1-02 = 2, 3, or 4)*3
V/f control?

YES 㧔A1-02=0 or 1)
V/f
Control mode selection
PG?
YES
NO 㧔A1-02=1㧕
(Default:
A1-02=0)
Set E1-03. Set E1-03, E2-04, and F1-01. *2
V/f default: 200V/50Hz(400V/50Hz) V/f default: 200V/50Hz(400V/50Hz)

Motor cable over OK to operate Load is

NO YES
50 m or heavy load possibly motor during connected to motor when
causing motor to stall autotuning? *1
operating motor first time
or overload? YES after autotuning?

NO YES

Stationary autotuning for Rotational *4 Stationary *4 Stationary *4

line-to-line resistance only autotuning autotuning 1 autotuning 2

END

Note If the motor cable changes to 50 m or longer for the actual installation, perform stationary autotuning for the line-to-line resistance only on-site.
* 1. Use rotational autotuning to increase autotuning accuracy whenever it is okay for the motor to be operated. Always perform rotational autotuning when
using open-loop vector 2 control.
* 2. If there is a reduction gear between the motor and PG, set the reduction ratio in F1-12 and F1-13.
* 3. The default setting of the Inverter is for open-loop vector 1 control (A1-02 = 2).
* 4. If the maximum output frequency is different from the base frequency, set the maximum output frequency (E1-04) after autotuning.
Fig 4.3 Settings According to the Control Method

4-7
 „Setting the Control Method
Any of the following five control methods can be set.
Constant Set-
Control Method Basic Control Main Applications
ting
Variable speed control, particularly
control of multiple motors with one
V/f control A1-02 = 0 Voltage/frequency ratio fixed control
Inverter and replacing existing Invert-
ers
Applications requiring high-precision
Voltage/frequency ratio fixed control
V/f control with PG A1-02 = 1 speed control using a PG on the
with speed compensation using a PG
machine side
Variable speed control, applications
Open-loop vector 1 A1-02 = 2
Current vector control without a PG requiring speed and torque accuracy
control (factory setting)
using vector control without a PG
Very high-performance control with a
PG (simple servo drives, high-preci-
Flux vector control A1-02 = 3 Flux vector control
sion speed control, torque control, and
torque limiting)
Very high-performance control with-
Current vector control without a PG
out a PG (torque control without a PG,
Open-loop vector 2 with an ASR (speed controller)
A1-02 = 4 torque limiting, applications requiring
control (Always perform rotational autotun-
a 1:200 speed control range without a
ing.)
PG)

Note With vector control, the motor and Inverter must be connected 1:1. The motor capacity for which stable control is possible is 50% to 100% of the capac-
ity of the Inverter.

V/f Control (A1-02 = 0)

• Set either one of the fixed patterns (0 to E) in E1-03 (V/f Pattern Selection) or set F in E1-03 to specify a
user-set pattern as required for the motor and load characteristics in E1-04 to E1-13 in advanced program-
ming mode.
Simple operation of a general-purpose
motor at 60 Hz: E1-03 = 1
Simple operation of a general-purpose
motor at 50 Hz: E1-03 = F (default) or 0
If E1-03 = F, the default setting in the user setting from
E1-04 to E1-13 are for 50 Hz
• Perform stationary autotuning for the line-to-line resistance only if the motor cable is 50 m or longer for
the actual installation or the load is heavy enough to produce stalling. Refer to the following section on
Autotuning for details on stationary autotuning.

V/f Control with PG (A1-02=1)

• Set either one of the fixed patterns (0 to E) in E1-03 (V/f Pattern Selection) or set F in E1-03 to specify a
user-set pattern as required for the motor and load characteristics in E1-04 to E1-13 in advanced program-
ming mode.
Simple operation of a general-purpose
motor at 60 Hz: E1-03 = 1
Simple operation of a general-purpose
motor at 50 Hz: E1-03 = F (default) or 0
If E1-03 = F, the default setting in the user setting from
E1-04 to E1-13 are for 50 Hz
• Set the number of motor poles in E2-04 (Number of Motor Poles)
• Set the number of rotations per pulse in F1-01 (PG Constant). If there is a reduction gear between the
motor and PG, set the reduction ratio in F1-12 and F1-13 in advanced programming mode.

4-8
 Trial Operation Procedures

• Perform stationary autotuning for the line-to-line resistance only if the motor cable is 50 m or longer for
the actual installation or the load is heavy enough to produce stalling. Refer to the following section on
Autotuning for details on stationary autotuning.

Open-loop Vector 1 Control (A1-02 = 2)

Perform autotuning. If the motor can be operated, perform rotational autotuning. If the motor cannot be oper-
ated, perform stationary autotuning 1 or 2. Refer to the following section on Autotuning for details on autotun-
ing.

Flux Vector Control (A1-02 = 3)

Perform autotuning. If the motor can be operated, perform rotational autotuning. If the motor cannot be oper-
ated, perform stationary autotuning 1 or 2. Refer to the following section on Autotuning for details on autotun-
ing.

Open-loop Vector 2 Control (A1-02 = 4)

Perform autotuning. If the motor can be operated, perform rotational autotuning. If the motor cannot be oper-
ated, perform stationary autotuning 1 or 2. Refer to the following section on Autotuning for details on autotun-
ing.

‹ Autotuning
Use the following procedure to perform autotuning to automatically set motor constants when using the vector
control method, when the cable length is long, etc.
If the control method was changed after autotuning, be sure to perform autotuning again.
One of the following four autotuning modes can be set.
• Rotational autotuning
• Stationary autotuning 1
• Stationary autotuning for line-to-line resistance only
• Stationary autotuning 2

„ Precautions Before Using Autotuning

Read the following precautions before using autotuning.
• Autotuning the Inverter is fundamentally different from autotuning the servo system. Inverter autotuning
automatically adjusts parameters according to detected motor constants, whereas servo system autotuning
adjusts parameters according to the detected size of the load.
• When speed or torque precision is required at high speeds (i.e., 90% of the rated speed or higher), use a
motor with a rated voltage that is 20 V less than the input power supply voltage of the Inverter for 200V-
class Inverters and 40 V less for 400V-class Inverters. If the rated voltage of the motor is the same as the
input power supply voltage, the voltage output from the Inverter will be unstable at high speeds and suffi-
cient performance will not be possible.
• Use stationary autotuning 1 or 2 whenever performing autotuning for a motor that is connected to a load.
• Use rotational autotuning whenever performing autotuning for a motor that has fixed output characteris-
tics, when high precision is required, or for a motor that is not connected to a load.
• If rotational autotuning is performed for a motor connected to a load, the motor constants will not be found
accurately and the motor may exhibit abnormal operation. Never perform rotational autotuning for a motor
connected to a load.

4-9
 • If the wiring between the Inverter and motor changes by 50 m or more between autotuning and motor
installation, perform stationary autotuning for line-to-line resistance only.
• If the motor cable is long (50 m or longer), perform stationary autotuning for line-to-line resistance only
even when using V/f control.
• The status of the multi-function inputs and multi-function outputs will be as shown in the following table
during autotuning. When performing autotuning with the motor connected to a load, be sure that the hold-
ing brake is not applied during autotuning, especially for conveyor systems or similar equipment.

Tuning Mode Multi-function Inputs Multi-function Outputs

Same as during normal
Rotational autotuning Do not function.
operation

Maintain same status as

Stationary autotuning 1 Do not function.
when autotuning is started.

Stationary autotuning for line- Maintain same status as

Do not function.
to-line resistance only when autotuning is started.

Maintain same status as

Stationary autotuning 2 Do not function.
when autotuning is started.

• To cancel autotuning, always use the STOP Key on the Digital Operator.
• Power will be supplied to the motor when stationary autotuning is performed even though the motor will
not turn. Do not touch the motor until autotuning has been completed.

„Setting the Autotuning Mode

Rotational Autotuning (T1-01 = 0)

Rotational autotuning is used for open-loop vector control and flux vector control. Set T1-01 to 0, input the
data from the nameplate, and then press the RUN Key on the Digital Operator. The Inverter will stop the
motor for approximately 1 minute and then set the required motor constants automatically while operating the
motor for approximately 1 minute.

1. Always disconnect the motor from the machine and confirm that it is safe to operate the motor before
performing rotational autotuning.
2. If the motor cannot be operated by itself, perform stationary autotuning, but always use rotational
IMPORTANT autotuning whenever it is possible to operate the motor by itself to increase performance.

Stationary Autotuning 1 (T1-01 = 1)

Stationary autotuning1 is used for open-loop vector control and flux vector control. Set T1-01 to 1, input the
data from the nameplate, and then press the RUN Key on the Digital Operator. The Inverter will supply power
to the stationary motor for approximately 1 minute and some of the motor constants will be set automatically.
The remaining motor constants E2-02 (motor rated slip) and E2-03 (motor no-load current) will be set auto-
matically the first time operation is started in drive mode. To perform an operation immediately after station-
ary autotuning1, use the following procedure under the recommended conditions.
1. Check the values of E2-02 and E2-03 in verify mode or advanced programming mode.
2. Run the motor once in drive mode under the following conditions.
• The Inverter and the motor are connected.
• The motor shaft is not locked with a mechanical brake or other stopping mechanism (or function).
• A motor-load ratio of 30% or less is maintained.
• A speed of 30% or more of the base frequency set at E1-06 (default = highest frequency) is maintained at a
constant speed for one second or more.

4-10
 Trial Operation Procedures

3. After stopping the motor, check the values of E2-02 and E2-03 again in verify mode or advanced program-
ming mode. If the values of E2-02 and E2-03 differ from the ones before the first operation was carried
out, the settings have been successfully completed. Next, check if the values are suitable or not.
If the values of E2-02 and E2-03 differed greatly from the reference data of the motor in the test report or the
instruction manual, hunting, motor vibrations, insufficient motor torque, or an overcurrent may occur because
the motor is operated although the aforementioned conditions have not been fulfilled after stationary
autotuning1. For elevators, failure to observe this caution may result in the cage falling or injury. If so, per-
form stationary autotuning1 again and run the motor using the aforementioned procedure under the recom-
mended conditions or perform stationary autotuning 2 or rotational autotuning.
Usually the standard setting for E2-02 is 1 Hz to 3 Hz, and that for E2-03 is 30% to 65% of the rated current
for a general-purpose motor. Generally, the larger the motor capacity is, the smaller the rated slip and the ratio
of the no-load current to the rated current become. Use the data given in Factory Settings that Change with the
Inverter Capacity (o2-04) of Chapter 5 User Constants as a reference.

1. Power will be supplied to the motor when stationary autotuning 1 is performed even though the motor
will not turn. Do not touch the motor until autotuning has been completed.
2. When performing stationary autotuning 1 connected to a conveyor or other machine, ensure that the
IMPORTANT holding brake is not activated during autotuning.

Stationary Autotuning for Line-to-Line Resistance Only (T1-01 = 2)

Stationary autotuning for line-to-line resistance only can be used in any control method. This is the only auto-
tuning possible for V/f control and V/f control with PG modes.
Autotuning can be used to prevent control errors when the motor cable is long (50 m or longer) or the cable
length has changed since installation or when the motor and Inverter have different capacities.
Set T1-01 to 2, and then press the RUN Key on the Digital Operator. The Inverter will supply power to the sta-
tionary motor for approximately 20 seconds and the Motor Line-to-Line Resistance (E2-05) and cable resis-
tance will be automatically measured.

1. Power will be supplied to the motor when stationary autotuning for line-to-line resistance is performed
even though the motor will not turn. Do not touch the motor until autotuning has been completed.
2. When performing stationary autotuning connected to a conveyor or other machine, ensure that the
IMPORTANT holding brake is not activated during autotuning.

Stationary Autotuning 2 (T1-01 = 4)

If using Inverters for applications with constant loads such as for elevators, or with a motor load ratio exceed-
ing 30% at startup, and rotational autotuning without loads cannot be performed, perform stationary autotun-
ing 2 (T1-01=4).
Stationary autotuning 2 is used for open-loop vector control and flux vector control. Set T1-04 to 4, and Motor
no-load current (T1-09) will be added as a setting item. Input the data from the nameplate. Be sure to input the
value or motor no-load current (motor exciting current) from motor examination results to T1-09. After auto-
tuning, the value of T1-09 will be written in E2-03. When not setting T1-09, the value of Yaskawa standard
motor’s no-load current will be written in E2-03.

1. Power will be supplied to the motor when stationary autotuning 2 is performed even though the motor
will not turn. Do not touch the motor until autotuning has been completed.
2. When performing stationary autotuning 2 connected to a conveyor or other machine, ensure that the
IMPORTANT holding brake is not activated during autotuning.

4-11
 „Precautions for Rotational and Stationary Autotuning
Lower the base voltage based on Fig 4.4 to prevent saturation of the Inverter’s output voltage when the rated
voltage of the motor is higher than the voltage of the power supply to the Inverter. Use the following proce-
dure to perform autotuning.
1. Input the voltage of the input power supply to T1-03 (Motor rated voltage).
2. Input the results of the following formula to T1-05 (Motor base frequency):
(Base frequency from the motor’s nameplate × setting of T1-03)/(Rated voltage from motor’s nameplate)
3. Perform autotuning.
After having completed autotuning, set E1-04 (Max. output frequency) to the base frequency shown on the
motor nameplate.
Output voltage

Rated voltage from

motor nameplate
T1-03

Output frequency
0 Base frequency
Base frequency from motor nameplate
from motor nameplate ×T1-03

Rated voltage from motor nameplate

Fig 4.4 Motor Base Frequency and Inverter Input Voltage Setting

1. When speed precision is required at high speeds (i.e., 90% of the rated speed or higher), set T1-03 (Motor
rated voltage) to the input power supply voltage × 0.9.
2. When operating at high speeds (i.e., 90% of the rated speed or higher), the output current will increase as
IMPORTANT the input power supply voltage is reduced. Be sure to provide sufficient margin in the Inverter current.

„Precautions After Using Rotational and Stationary Autotuning

• After completing autotuning, set E1-04 (Max. output frequency) to the base frequency from the motor’s
nameplate.
• In stationary autotuning 1, when the motor is first operated in the drive mode after tuning, the remaining
motor constants E2-02 (Motor rated slip) and E2-03 (Motor no-load current) are set automatically. To per-
form an operation immediately after stationary autotuning 1, use the following procedure under the recom-
mended conditions.
1. Check the values of E2-02 and E2-03 in verify mode or advanced programming mode.
2. Run the motor once in drive mode under the following conditions.
• The Inverter and the motor are connected.
• The motor shaft is not locked with a mechanical brake or other stopping mechanism (or function).
• A motor-load ratio of 30% or less is maintained.
• A speed of 30% or more of the base frequency set at E1-06 (default = highest frequency) is maintained
at a constant speed for one second or more.
3. After stopping the motor, check the values of E2-02 and E2-03 again in verify mode or advanced program-
ming mode. If the values of E2-02 and E2-03 differ from the ones before the first operation was carried
out, the settings have been successfully completed. Next, check if the values are suitable or not.

4-12
 Trial Operation Procedures

If the values of E2-02 and E2-03 differed greatly from the reference data of the motor in the test report or the
instruction manual, hunting, motor vibrations, insufficient motor torque, or an overcurrent may occur because
the motor is operated although the aforementioned conditions have not been fulfilled after stationary autotun-
ing 1. For elevators, failure to observe this caution may result in the cage falling or injury. If so, perform sta-
tionary autotuning 1 again and run the motor using the aforementioned procedure under the recommended
conditions or perform stationary autotuning 2 or rotational autotuning.
Usually the standard setting for E2-02 is 1 Hz to 3 Hz, and that for E2-03 is 30% to 65% of the rated current
for a general-purpose motor. Generally, the larger the motor capacity is, the smaller the rated slip and the ratio
of the no-load current to the rated current become. Use the data given in Factory Settings that Change with the
Inverter Capacity (o2-04) of Chapter 5 User Constants as a reference.

4-13
 „ Constant Settings for Autotuning
The following constants must be set before autotuning.

Table 4.3 Constant Settings before Autotuning

Name Data Displays during Autotuning
Con-
Open Open
stant Setting Factory V/f Flux
Display -loop -loop
Num- Display Range Setting V/f with Vec-
Vec- Vec-
ber PG tor
tor 1 tor 2
Motor 1/2 When switching to motor 2 is
selection*1 selected, set the motor for
which autotuning is to be per-
formed. (This constant is
T1-00 1 or 2 1 Yes Yes Yes Yes Yes
ignored if motor 2 is not
选择电机 selected.)
1: Motor 1
2: Motor 2
Autotun- Set the autotuning mode.
ing mode 0: Rotational autotuning
selection 1: Stationary autotuning 1
2: Stationary autotuning for 0 to 4 2 (V/f)
T1-01 Yes Yes Yes Yes Yes
line-to-line resistance only *4 0 (Vector)
选择自学习
模式 3: Shipping adjustment*8
4: Stationary autotuning 2*9

Motor out-
put power
Set the output power of the 0.00 to 0.40 kW
T1-02 Yes Yes Yes Yes Yes
motor in kilowatts.*5 *7 650.00 kW *2
电机额定功
率

Motor 0.0 to
rated volt- 255.0 V 200.0 V
age (200 V (200 V
Set the rated voltage of the Class) Class)
T1-03 - - Yes Yes Yes
motor in volts.*5 *6 0.0 to 400.0 V
电机额定电 510.0 V (400 V
压
(400 V Class)
Class)
Motor
rated cur-
Set the rated current of the 0.32 to
T1-04 rent 1.90 A*2 Yes Yes Yes Yes Yes
motor in amps.*5 *7 6.40 A*3
电机额定电
流

Motor base
frequency Set the base frequency of the 0.0 to
T1-05 50.0 Hz - - Yes Yes Yes
电机基本频 motor in hertz.*5 *6 400.0 Hz
率

Number of
motor
poles
2 to 48
T1-06 Set the number of motor poles. 4 poles - - Yes Yes Yes
poles

电机极数

4-14
 Trial Operation Procedures

Table 4.3 Constant Settings before Autotuning (Continued)

Name Data Displays during Autotuning
Con-
Open Open
stant Setting Factory V/f Flux
Display -loop -loop
Num- Display Range Setting V/f with Vec-
Vec- Vec-
ber PG tor
tor 1 tor 2

Motor base
speed
Set the base speed of the motor 1450
T1-07 0 to 24000 - - Yes Yes Yes
in min−1.*5 min−1
电机额定速
度

Number of
PG pulses
when turn- Set the number of pulses for the
ing PG (pulse generator or
T1-08 encoder). Set the number of 0 to 60000 600 - Yes - Yes -
pulses per motor revolution
PG 脉冲数 without a multiplication factor.

Motor no- Set the current value recorded

load cur- in the motor’s test results for a
rent motor without a load. 0.00 to 1.89 1.20A
T1-09 No No Yes Yes Yes
Displayed only when Stationary *9 *2
电机的空载 autotuning 2 is selected (T1-01
电流 = 4).
* 1.
Not normally displayed. Displayed only when a motor switch command is set for a multi-function digital input (one of H1-01 to H1-10 set to 16).
* 2.
The factory setting depends on the Inverter capacity. Values are given for a 200 V Class, 0.4 kW Inverter.
* 3.
The setting range is from 10% to 200% of the Inverter rated output current. The value for a 200 V Class Inverter for a 0.4 kW is given.
* 4.
Set T1-02 and T1-04 when 2 is set for T1-01. Only set value 2 is possible for V/f control or V/f control with PG.
* 5.
For fixed output motors, set the base speed value.
* 6.
For Inverter motors or for specialized vector motors, the voltage or frequency may be lower than for general-purpose motors. Always confirm the infor-
mation on the nameplate or in test reports. If the no-load values are known, input the no-load voltage in T1-03 and the no-load current in T1-05 to
ensure accuracy.
* 7. The settings that will ensure stable vector control are between 50% and 100% of the Inverter rating.
* 8. Refer to Chapter 8 Procedure for Adjusting Constants after Replacement of Control Board (Page 8-3) for the details of setting 3 (Shipping adjustment).
* 9. The setting range depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. The upper limit depends on the setting of
E2-01.

Refer to page 3-15 for Digital Operator displays during autotuning.

„ Precautions for Precision Settings

Settings for autotuning are different when performing autotuning using motor test reports or design data. Use
the following table as reference.

Operator Display Simple Setting Precision Setting

Voltage under no-load con-
T1-03 Motor rated voltage
ditions at motor rated speed

Frequency under no-load

T1-05 Motor base frequency
conditions at rated speed

4-15
 ‹ Application Settings
User constants are set as required in advanced programming mode (“ADV” will be displayed on the LCD
screen). All the constants that can be set in quick programming mode can also be displayed and set in
advanced programming mode.

„Setting Examples
The following are examples of settings for applications.
• When using an Inverter-mounted braking resistor (ERF), set L8-01 to 1 to enable ERF braking resistor
overheating protection.
• To prevent the machine from being operated in reverse, set b1-04 to 1 to disable reverse operation.
• To increase the speed of a 50 Hz motor by 10%, set E1-04 to 55.0 Hz.
• To use a 0 to 10-V analog signal for a 50 Hz motor for variable-speed operation between 0 and 45.0 Hz
(0% to 90% speed deduction), set H3-02 to 90.0%.
• To control speed between 20% and 80% to ensure smooth gear operation and limit the maximum speed of
the machine, set d2-01 to 80.0% and set d2-02 to 20.0%.

‹ No-load Operation
To being no-load operation (without connecting the machine and the motor), press the LOCAL/REMOTE Key
on the Digital Operator to change to LOCAL mode (the SEQ and REF indicators on the Digital Operator
should be OFF).
Always confirm safety around the motor and machine before starting Inverter operation from the Digital
Operator. Confirm that the motor works normally and that no errors are displayed at the Inverter.
Jog Frequency Reference (d1-17, default: 6.00 Hz) can be started and stopped by pressing and releasing the
JOG Key on the Digital Operator. If the external sequence prevent operation from the Digital Operator, con-
firm that emergency stop circuits and machine safety mechanisms are functioning, and then start operation in
REMOTE mode (i.e., with a signal from the control signal terminals). The safety precautions must always be
taken before starting the Inverter with the motor connected to the machine.

Both a Run Command (forward or reverse) and a frequency reference (or multi-step speed reference) must
be provided to start Inverter operation.
Input these commands and reference regardless of the operation method (i.e., LOCAL of REMOTE).
INFO

‹ Loaded Operation
Connect the machine to the motor and then start operation as described for no-load operation (i.e., from the
Digital Operator or by using control circuit terminal signals).

„Connecting the Load

• After confirming that the motor has stopped completely, connect the mechanical system.
• Be sure to tighten all the screws when securing the motor shaft to the mechanical system.

4-16
 Trial Operation Procedures

„Operation using the Digital Operator

• Use the Digital Operator to start operation in LOCAL mode in the same way as in no-load operation.
• If fault occurs during operation, make sure the STOP Key on the Digital Operator is easily accessible.
• At first, set the frequency reference to a low speed of one tenth the normal operating speed.

„ Checking Operating Status

• Having checked that the operating direction is correct and that the machine is operating smoothly at slow
speed, increase the frequency reference.
• After changing the frequency reference or the rotation direction, check that there is no oscillation or abnor-
mal sound from the motor. Check the monitor display to ensure that U1-03 (Output Current) is not too
high.
• Continuously driving a general-purpose motor with its rated current at a speed of less than 20 Hz may
cause motor overheat. Further, if a current exceeding 70 to 80% of the load current flows for more than one
minute while the motor is running at a low speed, OL1 (Motor Overload) will be generated.
• When neither a braking unit (braking resistor) nor a regenerative converter is connected, some operation
conditions may cause an overvoltage. Check the DC bus voltage monitor (U1-07), and adjust the accelera-
tion/deceleration time, etc. as required. (200 V class: less than 350 V, 400 V class: less than 700 V)
• Refer to Adjustment Suggestions on page 4-18 if hunting, vibration, or other problems originating in the
control system occur.

‹ Check and Recording User Constants

Use verify mode (“VERIFY” will be displayed on the LCD screen) to check user constants that have been
changed for trial operation and record them in a user constant table.
Any user constants that have been change by autotuning will also be displayed in verify mode.
If required, the copy function in constants o3-01 and o3-02 displayed in advanced programming mode can be
used to copy the changed settings from the Inverter to a recording area in the Digital Operator. If changed set-
tings are saved in the Digital Operator, they can be easily copied back to the Inverter to speed up system
recovery if for any reason the Inverter has to be replaced.
The following functions can also be used to manage user constants.
• Recording user constants
• Setting access levels for user constants
• Setting a password

„ Recording User Constants (o2-03)

If o2-03 is set to 1 after completing trial operation, the settings of user constants will be saved in a separate
memory area in the Inverter. Later, after Inverter settings have been changed, the user constants can be initial-
ized to the settings saved in the separate memory area when o2-03 was set to 1 by setting A1-03 (Initialize) to
1110.

„User Constant Access Levels (A1-01)

A1-01 can be set to 0 (monitoring-only) to prevent user constants from being changed. A1-01 can also be set
to 1 (User-specified Constants) and used along with A2 constants to display only constants required by the
machine or application in a programming mode.

„Password (A1-04 and A1-05)

When the access level is set to monitoring-only (A1-01 = 0), a password can be set so that user constants will
be displayed only when the correct password is input.

4-17
 Adjustment Suggestions
If hunting, vibration, or other problems originating in the control system occur during trial operation,
adjust the constants listed in the following table according to the control method. This table lists only the
most commonly used user constants.

Table 4.4 Adjusted User Constants

Recom-
Control Name (Constant Factory
Performance mended Adjustment Method
Method Number) Setting
Setting
• Reduce the setting if
Controlling hunting torque is insufficient for
Hunting-prevention and vibration in mid- heavy loads.
1.00 0.50 to 2.00
gain (N1-02) dle-range speeds (10 to • Increase the setting if hunt-
40 Hz) ing or vibration occurs for
light loads.
• Increase the setting if
• Reducing motor motor magnetic noise is
Carrier frequency magnetic noise Depends high.
0 to
selection • Controlling hunting on capac- • Reduce the setting if hunt-
default
(C6-02) and vibration at low ity ing or vibration occurs at
speeds low to middle-range
speeds.
• Reduce the setting if
V/f control • Increasing torque
Torque compensation Depends torque or speed response is
(A1-02 = 0 and speed response 200 to 1000
primary delay time on capac- slow.
or 1) • Controlling hunting ms
constant (C4-02) ity • Increase the setting if hunt-
and vibration
ing or vibration occurs.
• Increase the setting if
• Improving torque at
torque is insufficient at
low speeds (10 Hz
Torque compensation low speeds.
or lower) 1.00 0.50 to 1.50
gain (C4-01) • Reduce the setting if hunt-
• Controlling hunting
ing or vibration occurs for
and vibration
light loads.
Middle output fre-
• Increase the setting if
quency voltage • Improving torque at Depends Default to torque is insufficient at
(E1-08) low speeds on capac- Default + 3 low speeds.
Minimum output fre- • Controlling shock at ity and
quency voltage startup voltage to 5 V* • Reduce the setting if shock
at startup is large.
(E1-10)
• Increasing torque
• Reduce the setting if
Speed feedback detec- and speed response
torque or speed response is
tion control (AFR) • Controlling hunting
1.00 0.50 to 2.00 slow.
gain and vibration in mid-
• Increase the setting if hunt-
(N2-01) dle-range speeds (10
ing or vibration occurs.
to 40 Hz)
• Reduce the setting if
• Increasing torque
Torque compensation torque or speed response is
Open-loop and speed response 20 to
primary delay time 20 ms slow.
vector 1 • Controlling hunting 100 ms
constant (C4-02) • Increase the setting if hunt-
control and vibration
ing or vibration occurs.
(A1-02 = 2)
• Increasing speed • Reduce the setting if speed
Slip compensation pri-
response 100 to response is slow.
mary delay time (C3- 200 ms
• Improving speed sta- 500 ms • Increase the setting if the
02)
bility speed is not stable.
• Increase the setting if
Slip compensation • Improving speed speed response is slow.
1.0 0.5 to 1.5
gain (C3-01) accuracy • Reduce the setting if the
speed is too fast.

4-18
 Adjustment Suggestions

Table 4.4 Adjusted User Constants (Continued)

Recom-
Control Name (Constant Factory
Performance mended Adjustment Method
Method Number) Setting
Setting
• Reducing motor • Increase the setting if
magnetic noise motor magnetic noise is
Depends
Carrier frequency • Controlling hunting 0 to high.
on capac-
selection (C6-02) and vibration at low default • Reduce the setting if hunt-
ity
Open-loop speeds (10 Hz or ing or vibration occurs at
vector 1 less) low speeds.
control Middle output fre-
(A1-02 = 2) quency voltage • Increase the setting if
• Improving torque at Depends Default to torque or speed response is
(E1-08) low speeds on capac- Default + 1 slow.
Minimum output fre- • Controlling shock at ity and
quency voltage startup voltage or 2 V*1 • Reduce the setting if shock
at startup is large.
(E1-10)
• Increase the setting if
ASR proportional gain • Torque and speed
torque or speed response is
1 (C5-01) and response 10.00 to
20.00 slow.
ASR proportional gain • Controlling hunting 50.00
• Reduce the setting if hunt-
2 (C5-03) and vibration
ing or vibration occurs.
ASR integral time 1 • Reduce the setting if
• Torque and speed
(high-speed) (C5-02) torque or speed response is
response 0.300 to
and 0.500 s slow.
• Controlling hunting 1.000 s
ASR integral time 2 • Increase the setting if hunt-
and vibration
(low-speed) (C5-04) ing or vibration occurs.
Set the output frequency at
Switching the ASR which to change the ASR
Flux vector proportional gain and 0.0 to max. proportional gain and inte-
ASR switching fre-
control integral time accord- 0.0 Hz output fre- gral time when the same val-
quency (C5-07)
(A1-02 = 3) ing to the output fre- quency ues cannot be used for both
quency high-speed and low-speed
operation.
Increase the setting if
ASR primary delay • Controlling hunting 0.004 to
0.004 s machine rigidity is low and
time (C5-06) and vibration 0.020 s
the system vibrates easily.
• Increase the setting if
• Reducing motor motor magnetic noise is
magnetic noise Depends 2.0 kHz to high.
Carrier frequency
• Controlling hunting on the • Reduce the setting if hunt-
selection (C6-02)
and vibration at low capacity. default*2 ing or vibration occurs at
speeds (3 Hz or less) low to middle-range
speeds.
• Increase the setting if
torque or speed response is
ASR proportional gain • Torque and speed
slow. (Refer to Procedure
1 (C5-01) and response 10.00 to
10.00 for Increasing the Speed
Open-loop ASR proportional gain • Controlling hunting 50.00
Response below.)
vector 2 2 (C5-03) and vibration
• Reduce the setting if hunt-
control ing or vibration occurs.
(A1-02 = 4)
ASR integral time 1 • Reduce the setting if
• Torque and speed
(high-speed) (C5-02) torque or speed response is
response 0.300 to
and 0.500 s slow.
• Controlling hunting 1.000 s
ASR integral time 2 • Increase the setting if hunt-
and vibration
(low-speed) (C5-04) ing or vibration occurs.

4-19
 Table 4.4 Adjusted User Constants (Continued)
Recom-
Control Name (Constant Factory
Performance mended Adjustment Method
Method Number) Setting
Setting
Set the output frequency at
Switching the ASR which to change the ASR
proportional gain and 0.0 to max. proportional gain and inte-
ASR switching fre-
integral time accord- 0.0 Hz output fre- gral time when the same val-
quency (C5-07)
ing to the output fre- quency ues cannot be used for both
quency high-speed and low-speed
operation.
Increase the setting if
0.04 to machine rigidity is low and
0.010 s
0.020 s the system vibrates easily.
ASR primary delay • Controlling hunting
(Enabled in the range 0 to
time (C5-06) and vibration
0.010 to 35 Hz. Refer to Procedure
0.035 s for Increasing the Speed
0.035 s
Response below.)
Increase the setting if
machine rigidity is low and
ASR primary delay • Controlling hunting 0.010 to the system vibrates easily.
0.010 s
time 2 (C5-10) and vibration 0.035 s (Enabled above 35 Hz. Refer
to Procedure for Increasing
the Speed Response below.)
(Enabled below the N4-11
Open-loop setting.)
vector 2 • Reduce the setting if speed
control response is slow. (Typi-
• Speed response
(A1-02 = 4) Integral time of speed • Controlling hunting 0.030 ms
0.015 to cally, reduce in intervals of
estimator (N4-07) 0.060 ms 0.05. Refer to Procedure
and vibration
for Increasing the Speed
Response below.)
• Increase the setting if hunt-
ing or vibration occurs.
(Enabled below the N4-11
setting.)
• Increase the setting if
speed response is slow.
High-speed propor- • Speed response (Typically, increase in
tional gain of speed • Controlling hunting 15 10 to 60 intervals of 5. Refer to
estimator (N4-10) and vibration Procedure for Increasing
the Speed Response
below.)
• Reduce the setting if hunt-
ing or vibration occurs.
• Increase the setting if
• Reducing motor motor magnetic noise is
magnetic noise Depends high.
Carrier frequency Default
• Controlling hunting on the • Reduce the setting if hunt-
selection (C6-11) value
and vibration at low capacity. ing or vibration occurs at
speeds (3 Hz or less) low to middle-range
speeds.
* 1. The setting is given for 200 V Class Inverters. Double the voltage for 400 V Class Inverters.
* 2. The factory setting for 400V 132kW and 220kW flax vector control (A1-02 = 3) is 1.5 kHz, for software version VSG123032 or later.

4-20
 Adjustment Suggestions

Procedure for Increasing the Speed Response

Increase the speed response.

No
C5-01 ≥ 30.0 Increase the setting for the ASR proportional gain (C5-01).
(Typically, increase in intervals of 5.)

Yes

No Reduce the setting for the ASR primary delay time (C5-06).
C5-06 ≤ 0.01
(Typically, reduce in intervals of 0.01.)

Yes

Speed ≥ N4-11
Is the speed response to be Increase the setting for the high-speed proportional gain of
increased for low-speed
operation or high-speed
speed estimator (N4-10). (Typically, increase in intervals
operation? of 5.)

Speed < N4-11

Reduce the setting for the integral time of

speed estimator (N4-07). (Typically,
reduce in intervals of 0.005.)

• Do not change the Torque Compensation Gain (C4-01) from its default setting of 1.00 when using open-
loop vector 1 control.
• If speeds are inaccurate during regeneration in open-loop vector 1 control, enable Slip Compensation Dur-
ing Regeneration (C3-04 = 1).
• Use slip compensation to improve speed control during V/f control (A1-02 = 0).
Set the Motor Rated Current (E2-01), Motor Rated Slip (E2-02), and Motor No-load Current (E2-03), and
then adjust the Slip Compensation Gain (C3-01) to between 0.5 and 1.5. The default setting for V/f control
is C3-01 = 0.0 (slip compensation disabled).
• To improve speed response and stability in V/f control with a PG (A1-02 = 1), set the ASR constants (C5-
01 to C5-05) to between 0.5 and 1.5 times the default. (It is not normally necessary to adjust this setting.)
ASR for V/f control with a PG will only control the output frequency; a high gain, such as is possible for
open-loop vector 2 control or flux vector control, cannot be set.

The following user constants will also indirectly affect the control system.

Table 4.5 Constants Indirectly Affecting Control and Applications

Name (Constant Number) Application
Dwell function (b6-01 to b6-04) Used for heavy loads or large machine backlashes.
Used to soften the torque or to balance the load between two motors. Can
Droop function (b7-01 to b7-02)
be used when the control method (A1-02) is set to 3 or 4.
Acceleration/deceleration times
Adjust torque during acceleration and deceleration.
(C1-01 to C1-11)
S-curve characteristics (C2-01 to C2-04) Used to prevent shock when completing acceleration.
Jump frequencies (d3-01 to d3-04) Used to avoid resonance points during operation.
Analog input filter time constant (H3-12) Used to prevent fluctuations in analog input signals caused by noise.
Used to prevent overvoltage errors and motor stalling for heavy loads or
rapid acceleration/deceleration. Stall prevention is enabled by default and
Stall prevention
the setting does not normally need to be changed. When using a braking
(L3-01 to L3-06, L3-11, L3-12)
resistor, however, disable stall prevention during deceleration by setting
L3-04 to 0.

4-21
 Table 4.5 Constants Indirectly Affecting Control and Applications (Continued)
Name (Constant Number) Application
Set the maximum torque during vector control. If a setting is increased,
Torque limits (L7-01 to L7-04, L7-06, L7-07) use a motor with higher capacity than the Inverter. If a setting is reduced,
stalling can occur under heavy loads.
Used to increase response for acceleration/deceleration or to reduce over-
shooting when there is low machine rigidity and the gain of the speed
Feed forward control (N5-01 to N5-03) controller (ASR) cannot be increased. The inertia ratio between the load
and motor and the acceleration time of the motor running alone must be
set.

4-22
 User Constants
This chapter describes all user constants that can be set in the Inverter.

User Constant Descriptions .........................................5-2

Digital Operation Display Functions and Levels ..........5-3
User Constant Tables ..................................................5-8
 User Constant Descriptions
This section describes the contents of the user constant tables.

‹ Description of User Constant Tables

User constant tables are structured as shown below. Here, b1-01 (Frequency Reference Selection) is used as an
example.
Name Control Methods
Change
Con- Open Open MEMO-
Setting Factory during V/f -loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Reference Set the frequency reference
selection input method.
0: Digital Operator
1: Control circuit terminal
b1-01 (analog input) 0 to 4 1 No Q Q Q Q Q 180H -
频率指令选 2: MEMOBUS communi-
择 cations
3: Option board
4: Pulse train input

• Constant Number: The number of the user constant.

• Name: The name of the user constant.
• Description: Details on the function or settings of the user constant.
• Setting Range: The setting range for the user constant.
• Factory Setting: The factory setting (each control method has its own factory setting.
Therefore the factory setting changes when the control method is
changed.)
Refer to page 5-86 for factory settings by control method.
• Change during Operation: Indicates whether or not the constant can be changed while the
Inverter is in operation.
Yes: Changes possible during operation.
No: Changes not possible during operation.
• Control Methods: Indicates the control methods in which the user constant can be moni-
tored or set.
Q: Items which can be monitored and set in either quick program-
ming mode or advanced programming mode.
A: Items which can be monitored and set only in advanced pro-
gramming mode.
No: Items which cannot be monitored or set for the control method.
• MEMOBUS Register: The register number used for MEMOBUS communications.
• Page: Reference page for more detailed information on the constant.

5-2
 Digital Operation Display Functions and Levels

Digital Operation Display Functions and Levels

The following figure shows the Digital Operator display hierarchy for the Inverter.

No. Function Display Page

U1 Status Monitor Constants Monitor 5-77

MENU Drive Mode U2 Fault Trace Fault Trace 5-83
U3 Fault History Fault History 5-85
Inverter can be operated and
its status can be displayed.
A1 Initialize Mode Initialization 5-8
User
A2 User-specified Setting Mode Parameter 5-9
b1 Operation Mode Selections Sequence 5-10
b2 DC Injection Braking DC Braking 5-12
Speed
b3 Speed Search Search 5-13
b4 Timer Function Delay Timers 5-15
Quick Programming Mode
b5 PID Control PID Control 5-15
Minimum constants required b6 Dwell Functions Reference
5-17
Hold
for operation can be monitored Droop
b7 Droop Control Control 5-18
or set. Energy
b8 Energy Saving Saving 5-19
b9 Zero-servo Zero Servo 5-20
C1 Acceleration/Deceleration Accel/Decel 5-21
S-Curve
C2 S-curve Acceleration/Deceleration Acc/Dcc 5-22
Motor-Slip
C3 Motor Slip Compensation Comp 5-23
Torque
C4 Torque Compensation Comp 5-24
Advanced Programming Mode
C5 Speed Control (ASR) ASR Tuning 5-25
All constants can be monitored C6 Carrier Frequency Carrier Freq 5-26
Preset
or set. d1 Preset Reference Reference 5-27
Reference
d2 Reference Limits Limits 5-28
Jump
d3 Jump Frequencies Frequencies 5-29
d4 Reference Frequency Hold Sequence 5-29
d5 Torque Control Torque Control 5-30
Field-
d6 Field Weakening weakening 5-31
E1 V/f Pattern V/f Pattern 5-33
Verify Mode Motor
E2 Motor Setup Setup
5-34
Constants changed from the E3 Motor 2 V/f Pattern V/f Pattern 2 5-36
default settings can be moni- E4 Motor 2 Setup Motor Setup
5-37
2
tored or set. PG Option
F1 PG Option Setup Setup 5-38
F2 Analog Reference Board AI-14 Setup 5-40
DI-08, 16
F3 Digital Reference Board Setup 5-41
AO-08, 12
F4 Analog Monitor Boards Setup 5-42
DO-02,08
F5 Digital Output Boards Setup 5-43
ComOPT
F6 Communications Option Boards Setup 5-44
Autotuning Mode Digital
H1 Multi-function Contact Inputs Inputs 5-45
Digital
Automatically sets motor con- H2 Multi-function Contact Outputs Outputs 5-48
stants if autotuning data (from Analog
H3 Analog Inputs Inputs 5-50
motor nameplate) is input for H4 Multi-function Analog Outputs Analog
5-53
Outputs
open-loop vector control or to Serial Com
H5 MEMOBUS Communications 5-54
measure the line-to-line resis- Setup
Pulse I/O
tance for V/f control. H6 Pulse Train Setup 5-56
Motor
L1 Motor Overload Overload 5-57
PwrLoss
L2 Power Loss Ridethrough Ridethru 5-58
Stall
L3 Stall Prevention Prevention 5-60
Ref
L4 Reference Detection Detection 5-61
L5 Fault Restart Fault Restart 5-62
Torque
L6 Torque Detection Detection 5-63
L7 Torque Limits Torque Limit 5-64
Hdwe
L8 Hardware Protection Protection 5-65
N1 Hunting Prevention Function Hunting Prev 5-68
N2 Speed Feedback Protection Control AFR 5-69
N3 High-slip Braking High Slip 5-69
N4 Speed Estimation Observer 5-70
Feedfoward
N5 Feed Forward Cont 5-71
Monitor
o1 Monitor Select Select 5-72
Key
o2 Multi-function Selections Selections 5-74
COPY
o3 Copy Function Function 5-75

T Motor Autotuning Auto-Tuning 5-76

5-3
 ‹ User Constants Settable in Quick Programming Mode
The minimum user constants required for Inverter operation can be monitored and set in quick programming
mode. The user constants displayed in quick programming mode are listed in the following table. These, and
all other user constants, are also displayed in advanced programming mode.
Refer to the overview of modes on page 3-5 for an overview of quick programming mode.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f -loop Flux Loop BUS
stant Description Range Setting Opera-
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Control
Set the control method for the Inverter.
method 0: V/f control
selection
1: V/f control with PG
A1-02 0 to 4 2 No Q Q Q Q Q 102H
2: Open-loop vector 1 control
控制模式选 3: Flux vector control
择 4: Open-loop vector 2 control

Reference Set the frequency reference input

selection method.
0: Digital Operator
1: Control circuit terminal (analog
b1-01 0 to 4 1 No Q Q Q Q Q 180H
频率指令选
input)
择 2: MEMOBUS communications
3: Option board
4: Pulse train input
Operation Set the Run Command input method
method 0: Digital Operator
selection 1: Control circuit terminal (sequence
b1-02 0 to 3 1 No Q Q Q Q Q 181H
input)
运行指令选 2: MEMOBUS communications
择 3: Option board

Stopping
Select stopping method when Stop
methodCommand is sent.
selection
0: Deceleration to stop
1: Coast to stop
2: DC braking stop (Stops faster than 0 to 3
b1-03 0 No Q Q Q Q Q 182H
coast to stop, without regenerative *10
停止方法选 operation.)
择 3: Coast to stop with timer (Run
Commands are disregarded during
deceleration time.)
Accelera- Set the acceleration time in seconds
C1-01 tion time 1 for the output frequency to climb from Yes Q Q Q Q Q 200H
加速时间 1 0% to 100%. 0.0 to
6000.0 10.0 s
Decelera- Set the deceleration time in seconds *1
C1-02 tion time 1 for the output frequency to fall from Yes Q Q Q Q Q 201H
减速时间 1 100% to 0%.

Carrier fre-
quency Select carrier wave fixed pattern.
selection 1 to F 6 No
C6-02 Select F to enable detailed settings No Q Q Q Q 224H
*11 *2 *13
载波频率选
using constants C6-03 to C6-07.
择

5-4
 Digital Operation Display Functions and Levels

Name Control Methods

Change Open Open MEMO-
Con-
Setting Factory during V/f -loop Flux Loop BUS
stant Description Range Setting Opera-
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Carrier fre-
quency for Select carrier frequency when open-
open-loop loop vector 2 control is used.
vector 2 1: 2kHz 1 No No No No
C6-11 1 to 4 No *13 *13 Q 22DH
control 2: 4kHz *2 *13 *13
3: 6kHz
无 PG 矢量 4: 8kHz
2 载波

Frequency Set the frequency reference in the unit

reference 1 specified in o1-03 (Frequency Units
d1-01 0.00 Hz Yes Q Q Q Q Q 280H
for Reference Setting And Monitor,
频率指令 1 default: Hz)

Frequency Frequency reference when multi-step

d1-02 reference 2 speed reference 1 is ON for a multi- 0.00 Hz Yes Q Q Q Q Q 281H
频率指令 2 function input (unit: Set in o1-03).

Frequency Frequency reference when multi-step

d1-03 reference 3 speed reference 2 is ON for a multi- 0 to 0.00 Hz Yes Q Q Q Q Q 282H
频率指令 3 function input (unit: Set in o1-03). 400.00
*7
Frequency Frequency reference when multi-step
reference 4 speed reference 1 and 2 are ON for a
d1-04 0.00 Hz Yes Q Q Q Q Q 283H
multi-function input (unit: Set in o1-
频率指令 4 03).

Jog
Frequency reference when Jog Fre-
frequency
quency Selection, FJOG command, or
reference
d1-17 6.00 Hz Yes Q Q Q Q Q 292H
RJOG command is ON for a multi-
点动频率上 function input (unit: Set in o1-03).
限

Input volt- Set the Inverter input voltage in 1 volt. 155 to

age setting 200 V
E1-01 This set value will be the basis for the 255 No Q Q Q Q Q 300H
*3
输入电压 protection functions. *3

V/f pattern
selection 0 to E: Select from 15 preset patterns.
E1-03 F: Custom user-set patterns (Applica- 0 to F F No Q Q No No No 302H
V/F 曲线设 ble for setting E1-04 to E1-10).
定

5-5
 Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f -loop Flux Loop BUS
stant Description Range Setting Opera-
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Max.
output
frequency 40.0 to
50.0 Hz
E1-04 (FMAX) 400.0 No Q Q Q Q Q 303H
*4
*7
最高输出频 Output voltage (V)
VMAX
率 (E1-05)
(V BASE)
(E1-13)
Max.
voltage
VC
(E1-08) 0.0 to 200.0
E1-05 (VMAX) VMIN 255.0 V No Q Q Q Q Q 304H
(E1-10) *3 *3*4
FMIN FB FA FMAX
最大电压 (E1-09) (E1-07) (E1-06) (E1-04)
Frequency (Hz)
Base fre-
quency To set V/f characteristics in a straight 0.0 to
50.0 Hz
E1-06 (FA) line, set the same values for E1-07 and 400.0 No Q Q Q Q Q 305H
*4
E1-09. In this case, the setting for E1- *7
基本频率 08 will be disregarded.
Min. out- Always ensure that the four frequen-
put fre- cies are set in the following manner:
quency E1-04 (FMAX) ≥ E1-06 (FA) > E1-07 0.0 to
(FB) ≥ E1-09 (FMIN) 0.5 Hz
E1-09 (FMIN) 400.0 No Q Q Q A Q 308H
*4
*7
最低输出频
率

Base Change this setting only when making

voltage advanced adjustments for V/f in the 0.0 to
0.0 V
E1-13 (VBASE) fixed outputs area. Normally, there is 255.0 No A A Q Q Q 30CH
*5
no need to make these settings. *3
基本电压

Motor Set the motor rated current in amps.

rated cur-
This set value becomes the base value 0.32 to
rent 1.90 A
E2-01 for motor protection, torque limit, and 6.40 No Q Q Q Q Q 30EH
*2
电机额定电
torque control. It is set automatically *6

流 when using autotuning.

Number of
motor Set the number of motor poles. The
E2-04 poles value is set automatically during auto- 2 to 48 4 poles No No Q No Q Q 311H
tuning.
电机极数

Motor
rated Set the output of the motor in units of
output 0.00 to 0.40
E2-11 0.01kW. This constant is automatically No Q Q Q Q Q 318H
650.00 *8
电机额定功
set during autotuning.
率

PG con- Set the number of pulses per rotation

stant for the PG (pulse generator or 0 to
F1-01 600 No No Q No Q No 380H
encoder) being used. (Do not set as a 60000
PG 脉冲数 multiple.)

Gain (ter- Set the voltage level gain for multi-

minal FM) function analog output 1.
Set the number of multiples of 10 V to
be output as the 100% output for the 0.00 to
H4-02 1.00 Yes Q Q Q Q Q 41EH
端子 FM 增 monitor items. Voltage output from the 2.50
益 terminals, however, have a 10 V max.
meter calibration function.*13

5-6
 Digital Operation Display Functions and Levels

Name Control Methods

Change Open Open MEMO-
Con-
Setting Factory during V/f -loop Flux Loop BUS
stant Description Range Setting Opera-
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Gain (ter- Set the voltage level gain for multi-
minal AM) function analog output 2.
Set the number of multiples of 10 V to
be output as the 100% output for the 0.00 to
H4-05 monitor items. Voltage output from the 0.50 Yes Q Q Q Q Q 421H
端子 AM 增
2.50
益
terminals, however, have a 10 V max.
A meter calibration function is avail-
able.*13
Motor pro- Set to enable or disable the motor
tection overload protection function using the
selection electronic thermal relay.
0: Disabled
1: General-purpose motor protection
2: Inverter motor protection
3: Vector motor protection
In some applications when the
L1-01 0 to 3 1 No Q Q Q Q Q 480H
Inverter power supply is turned off,
电机保护功 the thermal value is reset, so even if
能选择 this constant is set to 1, protection
may not be effective.
When several motors are connected to
one Inverter, set to 0 and ensure that
each motor is installed with a protec-
tion device.

Stall pre-
0: Disabled (Deceleration as set. If
vention deceleration time is too short, a
selection main circuit overvoltage may
during result.)
decelera-
1: Enabled (Deceleration is stopped
tion when the main circuit voltage
exceeds the overvoltage level.
Deceleration restarts when voltage
is returned.)
2: Intelligent deceleration mode 0 to 3
L3-04 1 No Q Q Q Q Q 492H
(Deceleration rate is automatically *9
adjusted so that the Inverter can
减速防止失
decelerate in the shortest possible
速选择 time. Set deceleration time is
disregarded.)
3: Enabled (with Braking Resistor
Unit)
When a braking option (Braking
Resistor, Braking Resistor Unit, Brak-
ing Unit) is used, always set to 0 or 3.

* 1. The setting range for acceleration/deceleration times depends on the setting of C1-10 (Acceleration/deceleration Time Setting Unit). If C1-10 is set to 0,
the setting range is 0.00 to 600.00 (s).
* 2. The factory settings depend on the Inverter capacity. The values for a 200 V Class Inverter for 0.4 kW are given.
* 3. These are values for a 200 V Class Inverter. Values for a 400 V Class Inverter are double.
* 4. The factory setting will change when the control method is changed. The open-loop vector 1 factory settings are given.
* 5. E1-13 is set to the same value as E1-05 by autotuning.
* 6. The setting range is from 10% to 200% of the Inverter rated output current. The value for a 200 V Class Inverter for 0.4 kW is given.
For the motor no-load current, set E2-03 to a value less than that of E2-01.
* 7. The setting range for open-loop vector 2 control is 0 to 132.0.
* 8. The same capacity as that of the Inverter will be set if the constants are initialized.
* 9. The setting range for flux vector and open-loop vector 2 control is 0 to 2.
* 10.0 or 1 for flux vector control and open-loop vector 2 control.
* 11.The setting range depends on the capacity of the Inverter. The values for a 200 V Class Inverter for 0.4 kW are given.
* 12.Displayed in Quick Programming Mode when motor 2 is set for a multi-function input.
* 13.The CH1 output can be adjusted when the H4-02 or H4-03 setting is displayed in Quick, Advanced, or Verify mode while the motor is stopped.
The CH2 output can be adjusted when the H4-05 or H4-06 setting is displayed in quick, Advance, or Verify mode while the motor is stopped.
For analog output, the value equivalent to 100% of output value of monitored item is multiplied by the gain setting and the set bias is added.

5-7
 User Constant Tables

‹ A: Setup Settings
The following settings are made with the environment constants (A constants): Language displayed on the
Digital Operator, access level, control method, initialization of constants.

„ Initialize Mode: A1
User constants for the environment modes are shown in the following table.
Name Control Methods
Change
Con- Open Open MEMO-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Language Used to select the language
selection for displayed on the Digital
Digital Operator (LCD).
Operator 0: English
display 1: Japanese
2: German
A1-00 3: French 0 to 7 7 Yes A A A A A 100H -
4: Italian
5: Spanish
语言选择 6: Portuguese
7: Chinese
This constant is not initialized
by the initialize operation.

Constant
Used to set the constant
access level
access level (set/read.)
0: Monitoring only
(Monitoring drive mode
and setting A1-01 and A1-
04.)
1: Used to select user
constant
4-17
A1-01 (Only constants set in A2- 0 to 2 2 Yes A A A A A 101H 6-156
参数的访问级 01 to A2-32 can be read
and set.)
2: Advanced
(Constants can be read
and set in both quick
programming mode and
advanced programming
(A) mode.)

ControlUsed to select the control

method method for the Inverter
selection
0: V/f control
1: V/f with PG feedback
2: Open-loop vector 1 con- 4-5
A1-02 trol 0 to 4 2 No Q Q Q Q Q 102H 4-7
3: Flux vector 4-18
控制模式选择 4: Open-loop vector 2 con-
trol
This constant is not initialized
by the initialize operation.

5-8
 User Constant Tables

Name Control Methods

Change
Con- Open Open MEMO-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Initialize Used to initialize the con-
stants using the specified
method.
0: No initializing
1110: Initializes using the
User constants 0 to 6-11
A1-03 0 No A A A A A 103H 6-150
初始化 2220: Initializes using a 3330
two-wire sequence.
(Initializes to the
factory setting.)
3330: Initializes using a
three-wire sequence.
Password Password input when a pass-
word has been set in A1-05.
This function write-protects
some constants of the initial-
ize mode.
0 to 4-17
A1-04 If the password is changed, 0 No A A A A A 104H 6-157
密码 9999
A1-01 to A1-03 and A2-01 to
A2-32 constants can no
longer be changed. (Program-
ming mode constants can be
changed.)

Password Used to set a four digit num-

setting ber as the password.
This constant is not usually
displayed. When the Pass-
0 to 4-17
A1-05 word (A1-04) is displayed, 0 No A A A A A 105H 6-157
9999
密码设定 hold down the RESET Key
and press the Menu Key and
the password will be dis-
played.

„User-set Constants: A2
The constants set by the user are listed in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
User setting Used to set the constant num-
constants bers that can be set/read.
Maximum 32.
A2-01 Effective when the Constant b1-01 106H
to Access Level (A1-01) is set to to - No A A A A A to 6-157
A2-32 用户参数 User Program (1). Constants o3-02 125H
set in constants A2-01 to A2-
32 can be set/read in pro-
gramming mode.

5-9
 ‹ b: Application Constants
The following settings are made with the application constants (B constants): Operation method selection, DC
injection braking, speed searching, timer functions, dwell functions, droop control, energy saving control, and
zero-servo control.

„Operation Mode Selections: b1

User constants for operation mode selection are shown in the following table.
Name Control Methods
Change
Con- Open Open MEMO-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Reference Set the frequency reference
selection input method.
0: Digital Operator
4-5
1: Control circuit terminal
6-2
b1-01 (analog input) 0 to 4 1 No Q Q Q Q Q 180H
频率指令选
6-76
2: MEMOBUS communica-
择 6-94
tions
3: Option board
4: Pulse train input
Operation Set the Run Command input
method method.
selection 0: Digital Operator 4-5
1: Control circuit terminal 6-10
b1-02 0 to 3 1 No Q Q Q Q Q 181H
(sequence input) 6-76
运行指令选 2: MEMOBUS communica- 6-94
择 tions
3: Option board

Stopping Used to set the stopping

method method used when a Stop
selection Command is input.
0: Deceleration to stop
1: Coast to stop
2: DC injection braking stop
4-6
b1-03 (Stops faster than coast to 0 to 3 * 0 No Q Q Q Q Q 182H
6-12
停止方法选
stop, no regenerative
择 operation.)
3: Coast to stop with timer
(Run Commands are
disregarded during
deceleration.)

Prohibition
of reverse
operation 0: Reverse enabled
b1-04 0 or 1 0 No A A A A A 183H 6-62
1: Reverse disabled
反转禁止选
择

5-10
 User Constant Tables

Name Control Methods

Change
Con- Open Open MEMO-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Operation Used to set the method of
selection operation when the fre-
for setting quency reference input is less
E1-09 or than the minimum output fre-
less quency (E1-09).
0: Run at frequency reference
(E1-09 not effective).
b1-05 1: STOP (Frequencies below 0 to 3 0 No No No No A No 184H 6-12
E1-09 in the coast to stop
不足最低频
state.)
率动作 2: Run at min. frequency.
(E1-09)
3: Run at zero-speed (Fre-
quencies below E1-09 are
zero)
Read Used to set the responsiveness
sequence of the control inputs (forward/
input twice reverse and multi-function
inputs.)
b1-06 0: One scan every 5 ms (Use 0 or 1 1 No A A A A A 185H -
顺控输入扫
for fast responses.)
描 1: Two scans every 5 ms (Use
for possible malfunction
due to noise.)
Operation Used to set the operation mode
selection by switching to the Remote
after mode using the Local/Remote
switching to Key.
remote 0: Run signals that are input
mode during mode switching are
b1-07 disregarded. (Input Run 0 or 1 0 No A A A A A 186H -
signals after switching the
mode.)
本地 / 远程 1: Run signals become
切换 effective immediately after
switching to the Remote
mode.
Run Com- Used to set an operation inter-
mand selec- lock in programming modes.
tion in 0: Cannot operate.
program- 1: Can operate (Disabled
ming modes when Digital Operator is
b1-08 set to select Run Command 0 to 2 0 No A A A A A 187H -
(when b1-02 = 0)).
PRG 指令选 2: Cannot operate. (Cannot be
择 in programming mode
during operation.)
Mode selec- Enable for machines that
tion for rotate the motor only in the
zero-speed same direction as the speed
reference. This setting
b1-10 0 or 1 0 No No No No No A 1DEH -
improves the control stability
零速时动作 of the motor at zero-speed.
选择 0: Disabled
1: Enabled
* 0 or 1 for flux vector control and open-loop vector 2 control.

5-11
 „DC Injection Braking: b2
User constants for injection braking are shown in the following table.

Name Control Methods

Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Zero-speed Used to set the frequency
level (DC which starts DC injection
injection braking in units of Hz when
braking start- deceleration to stop is
0.0 to 6-12
b2-01 ing fre- selected. 0.5 Hz No A A A A A 189H
10.0 6-145
quency) When b2-01 is less than E1-
09, E1-09 becomes the DC
直流制动开始 injection braking starting fre-
频率 quency.

DC injection
braking cur- Sets the DC injection braking
0 to 6-12
b2-02 rent current as a percentage of the 50% No A A A No No 18AH
100 6-16
Inverter rated current.
直流制动电流

DC injection Used to set the time to per-

braking time form DC injection braking at
at start start in units of 1 second. 0.00
6-13
b2-03 Used to stop coasting motor to 0.00 s No A A A A A 18BH
6-16
and restart it. When the set 10.00
起动制动时间 value is 0, DC injection brak-
ing at start is not performed.

DC injection Used to set the time to per-

braking time form DC injection braking at
at stop stop in units of 1 second.
0.00
Used to prevent coasting after
b2-04 to 0.50 s No A A A A A 18CH 6-13
the Stop Command is input.
10.00
停止制动时间 When the set value is 0.00,
DC injection braking at stop
is not performed.
Magnetic flux
compensa- Sets the magnetic flux com-
0 to
b2-08 tion volume pensation as a percentage of 0% No No No A No No 190H -
1000
the no-load current.
磁通量补偿

5-12
 User Constant Tables

„Speed Search: b3
User constants for the speed search are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Speed Enables/disables the speed
search search function for the Run
selection Command and sets the speed
(current search method.
detection or 0: Disabled, speed calculation
speed calcu- 1: Enabled, speed calculation
lation) 2: Disabled, current detection
3: Enabled, current detection

Speed Calculation:
When the search is started, the
motor speed is calculated and
b3-01 acceleration/deceleration is 0 to 3 2* No A A A No A 191H 6-65
performed from the calculated
speed to the specified
起动速度搜
frequency (motor direction is
索 also searched).

Current Detection:
The speed search is started
from the frequency when
power was momentarily lost
and the maximum frequency,
and the speed is detected at
the search current level.
Speed Sets the speed search operation
search oper- current as a percentage, taking
ating current the Inverter rated current as
(current 100%. 0 to
b3-02
detection) Not usually necessary to set. 200 100%* No A No A No A 192H 6-65
When restarting is not possible
速度搜索电 with the factory settings,
流 reduce the value.

Speed
search Sets the output frequency
decelera- deceleration time during speed
tion time search in 1-second units.
0.1 to
b3-03 (current Set the time for deceleration 2.0 s No A No A No No 193H 6-65
10.0
detection) from the maximum output fre-
quency to the minimum output
搜索减速时 frequency.
间

Speed Sets the magnetic contactor

search wait operating delay time when
time (cur- there is a magnetic contactor
rent detec- on the output side of the
tion or 0.0 to
b3-05 Inverter. When a speed search 0.2 s No A A A A A 195H 6-65
speed calcu- 20.0
is performed after recovering
lation) from a momentary power loss,
搜索延迟时
the search operation is delayed
间 by the time set here.

5-13
 Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Speed Operation restarts at a speed
search obtained by multiplying the
detection speed from the speed search by
compensa- the compensation gain (excita-
tion gain tion search only.) 1.00 to
b3-10 1.10 No A No A No A 19AH 6-65
(speed cal- Increase this setting if over- 1.20
culation) voltages occur when a speed
search is performed after a
搜索速度补 long baseblock, for example, in
偿增益 searches at startup.

Propor- Sets the proportional gain (PI

tional gain control) of the speed estimator
of the speed during speed search taking the
estimator setting of N4-08 as equivalent
during to a setting of 1.0.
speed search Usually, there is no need to 0.1 to
b3-13 1.0% No No No No No A 19DH 6-66
change this setting. If, how- 2.0
ever, the load inertia is large
速度推定比
and overvoltages occur during
例增益 the search, reduce this setting.
Increase this setting for greater
speed coincidence response.

Rotation
direction 0: Disabled (operates with
search specified rotation direction)
b3-14 selection 1: Enabled (operates with 0 or 1 1 No A A A No A 19EH 6-66
rotation direction found by
旋转方向搜 search)
索选择

Speed
search Sets the current level to retry a
retrial cur- speed search as a percentage, 0 to
b3-17 rent level 150% No A No A No A 1F0H 6-66
taking the Inverter rated cur- 200
rent as 100%.
搜索重试 I
值

Speed
search
retrial detec- Sets the time for detection in a 0.00 to
b3-18 tion time speed search retrial in units of 0.10 s No A No A No A 1F1H 6-66
1.00
seconds.
速度搜索检
出时间

Number of
speed search
retrials Sets the number of times that a
b3-19 0 to 10 0 No A No A No A 1F2H 6-66
speed search can be retried.
速度搜索重
试次数

* The factory setting will change when the control method is changed. The open-loop vector 1 factory settings are given.

5-14
 User Constant Tables

„Timer Function: b4
User constants for timer functions are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Timer func- Sets the timer function out-
tion ON- put ON-delay time (dead
delay time band) for the timer function
0.0 to
b4-01 input, in 1-second units. 0.0 s No A A A A A 1A3H 6-105
300.0
Enabled when a timer func-
ON 延迟时间 tion is set in H1-†† or H2-
††.
Timer func- Sets the timer function out-
tion OFF- put OFF-delay time (dead
delay time band) for the timer function
0.0 to
b4-02 input, in 1-second units. 0.0 s No A A A A A 1A4H 6-105
300.0
Enabled when a timer func-
OFF 延迟时间 tion is set in H1-†† or H2-
††.

„PID Control: b5
User constants for PID control are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
PID control 0: Disabled
method 1: Enabled (Deviation is D-
selection controlled.)
2: Enabled (Feedback value
is D-controlled.)
3: PID control enabled
b5-01 (frequency reference + 0 to 4 0 No A A A A A 1A5H 6-107
PID output, D control of
PID 控制选择 deviation)
4: PID control enabled
(frequency reference +
PID output, D control of
feedback value).
Proportional Sets P-control proportional
0.00
gain (P) gain as a percentage.
b5-02 to 1.00 Yes A A A A A 1A6H 6-107
P-control is not performed
PID 增益 25.00
when the setting is 0.00.

Integral (I) Sets I-control integral time in

time 1-second units. 0.0 to
b5-03 1.0 s Yes A A A A A 1A7H 6-107
I-control is not performed 360.0
PID 积分时间 when the setting is 0.0.

Integral (I) Sets the I-control limit as a

limit 0.0 to
b5-04 percentage of the maximum 100.0% Yes A A A A A 1A8H 6-107
100.0
PID 时间上限 output frequency.

Derivative Sets D-control derivative time

(D) time in 1-second units. 0.00 to
b5-05 0.00 s Yes A A A A A 1A9H 6-107
D-control is not performed 10.00
PID 微分时间 when the setting is 0.00.

5-15
 Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
PID upper Sets the upper limit after PID-
limit 0.0 to
b5-06 control as a percentage of the 100.0% Yes A A A A A 1AAH 6-107
100.0
PID 上限 maximum output frequency.

PID offset Sets the offset after PID-con- -100.0

b5-07 adjustment trol as a percentage of the to 0.0% Yes A A A A A 1ABH 6-107
PID 偏置 maximum output frequency. +100.0

PID first Sets the time constant for low

order lag time pass filter for PID-control 0.00 to
b5-08 constant 0.00 s Yes A A A A A 1ACH 6-107
outputs in 1-second units. 10.00
PID 延迟时间 Not usually necessary to set.

PID output Select forward/reverse for

characteris- PID output.
tics selection 0: PID output is forward.
b5-09 0 or 1 0 No A A A A A 1ADH 6-107
1: PID output is reverse
输出特性选择 (highlights the output
code)
PID output
gain 0.0 to
b5-10 Sets output gain. 1.0 No A A A A A 1AEH 6-107
25.0
PID 输出增益

PID reverse 0: 0 limit when PID output is

output selec- negative.
tion 1: Reverses when PID output
b5-11 0 or 1 0 No A A A A A 1AFH 6-107
is negative.
输出逆转选择 0 limit when reverse prohibit
is selected using b1-04.

Selection of 0: No detection of loss of

PID feed- PID feedback.
back com- 1: Detection of loss of PID
mand loss feedback.
detection Operation continues
during detection, with the
b5-12 malfunctioning contact 0 to 2 0 No A A A A A 1B0H 6-108
not operating.
2: Detection of loss of PID
反馈丧失检出 feedback.
Coasts to stop during
detection, and fault
contact operates.
PID feed-
back com-
mand loss Sets the PID feedback loss
detection detection level as a percent 0 to
b5-13 0% No A A A A A 1B1H 6-108
level units, with the maximum out- 100
put frequency at 100%.
反馈丧失
检出值

PID feed-
back com-
mand loss
detection Sets the PID feedback loss 0.0 to
b5-14 1.0 s No A A A A A 1B2H 6-108
time detection level in s units. 25.5

反馈丧失检出
时间

5-16
 User Constant Tables

Name Control Methods

Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
PID sleep
function
operation Set the PID sleep function 0.0 to
b5-15 0.0 Hz No A A A A A 1B3H 6-108
level start level as a frequency. 400.0

暂停动作值

PID sleep
operation Set the delay time until the
delay time 0.0 to
b5-16 PID sleep function starts in 0.0 s No A A A A A 1B4H 6-108
25.5
暂停动作延迟
seconds.
时间

Accel/decel
time for PID
reference Set the accel/decel time for 0.0 to
b5-17 0.0 s No A A A A A 1B5H 6-108
PID reference in seconds. 25.5
PID 加减速
时间

„Dwell Functions: b6
User constants for dwell functions are shown in the following table.
Name Control Methods
Con- Change Open Open MEMO-
Fac-
stant Setting during BUS
Num-
Description Range
tory
Opera-
V/f Loop Flux Loop Page
Display Setting V/f with Vec- Vec- Vec- Regis-
ber tion PG tor tor tor ter
1 2

Dwell fre-
quency at
0.0 to 4-21
b6-01 start 0.0 Hz No A A A A A 1B6H
400.0 6-22
起动暂停频
率

Dwell time Run command ON

OFF
at start 0.0 to 4-21
Output frequency
b6-02 0.0 s No A A A A A 1B7H
起动暂停时
10.0 6-22
间

Dwell fre- b6-01 b6-03 Time

quency at
b6-02 0.0 to 4-21
b6-03 stop
b6-04
0.0 Hz No A A A A A 1B8H
400.0 6-22
停止暂停频
The dwell function is used to output
率 frequency temporarily when driving
a motor with a heavy load.
Dwell time
at stop 0.0 to 4-21
b6-04 0.0 s No A A A A A 1B9H
停止暂停时
10.0 6-22
间

5-17
 „Droop Control: b7
User constants for droop functions are shown in the following table.

Name Control Methods

Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Droop control Sets the slip as a percentage
gain of maximum frequency when
the maximum output fre-
quency is specified and the
0.0 to 4-21
b7-01 rated torque occurs. 0.0 Yes No No No A A 1CAH
100.0 6-144
DROOP 增益 Droop-control is not per-
formed when the setting is
0.0.

Droop control Droop control responsive-

delay time ness constant 0.03 to 4-21
b7-02 0.05 s No A A A A A 1A4H
When hunting or oscillation 2.00 6-144
DROOP 延时 occurs, increase the value.

5-18
 User Constant Tables

„Energy Saving: b8
User constants for energy-saving control functions are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Energy-sav- Select whether to enable or
ing mode disable energy-saving con-
b8-01 selection trol. 0 or 1 0 No A A A A A 1CCH 6-115
0: Disable
节能模式设定 1: Enable

Energy-sav- Set the energy-saving gain

ing gain 0.0 to 0.7
b8-02 with the open-loop vector Yes No No A A A 1CDH 6-115
10.0 *1
节能增益 control method.

Energy-sav-
ing filter time Set the energy-saving filter 0.00 to 0.50 s
b8-03 constant time constant with the open- Yes No No A A A 1CEH 6-115
10.0 *2
loop vector control method.
节能滤波时间

Energy-sav- Set the maximum motor effi-

ing coeffi- ciency value.
cient Set the motor rated capacity 0.0 to
b8-04 in E2-11, and adjust the value 288.20 No A A No No No 1CFH 6-115
by 5% at a time until output 655.00 *3 *4
节能系数 power reaches a minimum
value.
Power detec-
tion filter
time constant Set the time constant for out- 0 to
b8-05 20 ms No A A No No No 1D0H 6-115
put power detection. 2000
电力检出滤波
时间

Search opera- Set the limit value of the volt-

tion voltage age control range during
limiter search operation.
Perform search operation to
optimize operations using 0 to
b8-06 0% No A A No No No 1D1H 6-115
minute variations in voltage 100
探索运行电压 using energy-saving control.
极限 Set to 0 to disable the search
operation. 100% is the motor
base voltage.
* 1. The factory setting is 1.0 when using flux vector control.
* 2. The factory setting is 2.00 s when Inverter capacity is 55 kW min.
The factory setting will change when the control method is changed. The open-loop vector 1 factory setting is given.
* 3. By setting E2-11 (Motor rated output) the appropriate value will be set.
* 4. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given.

5-19
 „Zero-servo: b9
User constants for dwell functions are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Zero-servo Adjust the strength of the
gain zero-servo lock.
Enabled when the “zero-servo
command” is set for the
multi-function input. When
the zero-servo command has
been input and the frequency
0 to
b9-01 reference drop below excita- 5 No No No No A No 1DAH 6-145
100
零伺服增益 tion level (b2-01), a position
control loop is created and the
motor stops. Increasing the
zero-servo gain in turn
increases the strength of the
lock. Increasing it by too
much will cause oscillation.

Zero-servo Sets the output width of the

completion P-lock completion signal.
width Enabled when the “zero-servo
completion (end)” is set for a
multi-function input. The
zero-servo completion signal
is ON when the current posi-
0 to
b9-02 tion is within the range (the 10 No No No No A No 1DBH 6-145
16383
zero-servo position + zero-
零伺服结束
幅度 servo completion width.)
Set the allowable position dis-
placement from the zero-
servo position to 4 times the
pulse rate of the PG (pulse
generator, encoder) in use.

5-20
 User Constant Tables

‹ C: Autotuning Constants
The following settings are made with the autotuning constants (C constants): Acceleration/deceleration times,
s-curve characteristics, slip compensation, torque compensation, speed control, and carrier frequency func-
tions.

„Acceleration/Deceleration: C1
User constants for acceleration and deceleration times are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Accelera- Sets the acceleration time to
4-5
tion time 1 accelerate from 0 to the maxi-
C1-01 Yes Q Q Q Q Q 200H 4-21
mum output frequency, in 1-
加速时间 1 6-18
second units.

Decelera- Sets the deceleration time to

4-5
tion time 1 decelerate from the maximum
C1-02 Yes Q Q Q Q Q 201H 4-21
output frequency to 0, in 1-
减速时间 1 6-18
second units.

Accelera- The acceleration time when

tion time 2 the multi-function input 4-21
C1-03 Yes A A A A A 202H
“accel/decel time 1” is set to 6-18
加速时间 2 ON.
Decelera- The deceleration time when
tion time 2 the multi-function input 4-21
C1-04 Yes A A A A A 203H
“accel/decel time 1” is set to 6-18
减速时间 2 ON.
Accelera- The acceleration time when
tion time 3 the multi-function input 4-21
C1-05 No A A A A A 204H
“accel/decel time 2” is set to 6-18
加速时间 3 ON. 0.0 to
6000.0 10.0 s
Decelera- The deceleration time when *
tion time 3 the multi-function input 4-21
C1-06 No A A A A A 205H
“accel/decel time 2” is set to 6-18
减速时间 3 ON.

Accelera- The acceleration time when

tion time 4 the multi-function input
4-21
C1-07 “accel/decel time 1” and No A A A A A 206H
6-18
加速时间 4 “accel/decel time 2” are set to
ON.

Decelera- The deceleration time when

tion time 4 the multi-function input
4-21
C1-08 “accel/decel time 1” and No A A A A A 207H
6-18
减速时间 4 “accel/decel time 2” are set to
ON.
Emergency
The deceleration time when
stop time
the multi-function input
“Emergency (fast) stop” is set
4-21
C1-09 to ON. No A A A A A 208H
6-17
紧急停止时间 This function can be used as a
stopping method when a fault
has been detected.

5-21
 Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Accel/decel
time setting
unit 0: 0.01-second units 4-21
C1-10 0 or 1 1 No A A A A A 209H
1: 0.1-second units 6-18
加减速时间
单位

Accel/decel Sets the frequency for auto-

time switch- matic acceleration/decelera-
ing fre- tion switching.
quency Below set frequency: Accel/
decel time 4
0.0 to 4-21
C1-11 Above set frequency: Accel/ 0.0 Hz No A A A A A 20AH
400.0 6-19
decel time 1
切换频率 The multi-function input
“accel/decel time 1” or
“accel/decel time 2” take pri-
ority.
* The setting range for acceleration/deceleration times depends on the setting of C1-10 (Acceleration/deceleration Time Setting Unit). If C1-10 is set to 0,
the setting range is 0.00 to 600.00 (s).

„S-curve Acceleration/Deceleration: C2
User constants for S-curve characteristics are shown in the following table.
Name Control Methods
Con- Change Open Open MEMO-
Fac-
stant Setting during BUS
Num-
Description Range
tory
Opera-
V/f Loop Flux Loop Page
Display Setting V/f with Vec- Vec- Vec- Regis-
ber tion PG tor tor tor ter
1 2

S-curve
characteris-
tic time at
0.00 to 4-21
C2-01 accelera- 0.20 s No A A A A A 20BH
tion start 2.50 6-19

加速开始 S
字

S-curve
characteris- All sections of the S-curve characteris-
tic time at tic time are set in seconds units. 0.00 to 4-21
C2-02 accelera- When the S-curve characteristic time is 0.20 s No A A A A A 20CH
tion end 2.50 6-19
set, the accel/decel times will increase
加速结束 S by only half of the S-curve characteris-
字 tic times at start and end.

S-curve Run Command

OFF
Output
characteris- frequency
ON
tic time at C2-02 C2-03
0.00 to 4-21
C2-03 decelera- 0.20 s No A A A A A 20DH
tion start
C2-01 C2-04 2.50 6-19
Time
减速开始 S
字

S-curve
characteris-
tic time at
0.00 to 4-21
C2-04 decelera- 0.00 s No A A A A A 20EH
tion end 2.50 6-19

减速结束 S
字

5-22
 User Constant Tables

„Motor Slip Compensation: C3

User constants for slip compensation are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Slip compen- Used to improve speed accu-
sation gain racy when operating with a
load.
Usually setting is not neces-
sary.
Adjust this constant at the fol-
lowing times. 0.0 to 4-18
C3-01 1.0* Yes A No A A No 20FH
• When actual speed is low, 2.5 6-36
滑差补偿增益 increase the set value.
• When actual speed is high,
decrease the set value.
Used as the applicable control
gain when using flux vector
control.

Slip compen- Slip compensation primary

sation pri- delay time is set in ms units.
mary delay Usually setting is not neces-
time sary.
Adjust this constant at the fol-
0 to 200 ms 4-18
C3-02 lowing times. No A No A No No 210H
10000 * 6-36
• Reduce the setting when
滑差补偿时间 slip compensation respon-
sive is slow.
• When speed is not stabi-
lized, increase the setting.
Slip compen- Sets the slip compensation
sation limit 0 to
C3-03 limit as a percentage of motor 200% No A No A No No 211H 6-36
250
滑差补偿极限 rated slip.

Slip compen- 0: Disabled.

sation selec- 1: Enabled.
tion during When the slip compensation
regeneration during regeneration function
has been activated, as regen-
C3-04 eration capacity increases 0 or 1 0 No A No A No No 212H 6-36
momentarily, it may be neces-
再生滑差补偿 sary to use a braking option
(braking resistor, Braking
Resistor Unit or Braking
Unit.)
Output volt- 0: Disabled.
age limit 1: Enabled. (The motor flux
operation will be lowered automati-
C3-05 0 or 1 0 No No No A A No 213H 6-36
selection cally when the output
voltage become satu-
输出电压限制 rated.)
* The factory setting will change when the control method is changed. The open-loop vector 1 factory settings are given.

5-23
 „Torque Compensation: C4
User constants for torque compensation are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Torque com- Sets torque compensation
pensation gain as a ratio.
gain Usually setting is not neces-
sary.
Adjust in the following cir-
cumstances:
• When the cable is long;
increase the set value.
• When the motor capacity is
smaller than the Inverter
capacity (Max. applicable
motor capacity), increase
the set values. 0.00 to 4-18
C4-01 1.00 Yes A A A No No 215H
• When the motor is oscillat- 2.50 6-39
转矩补偿增 ing, decrease the set val-
益 ues.
Adjust the output current
range at minimum speed rota-
tion so that it does not exceed
the Inverter rated output cur-
rent.
Do not alter the torque com-
pensation gain from its
default (1.00) when using the
open-loop vector 1 control
method.

Torque com- The torque compensation

pensation delay time is set in ms units.
primary Usually setting is not neces-
delay time sary.
constant Adjust in the following cir-
0 to 20 ms 4-18
C4-02 cumstances: No A A A No No 216H
10000 * 6-39
• When the motor is oscillat-
转矩补偿延
ing, increase the set values.
迟时间 • When the responsiveness
of the motor is low,
decrease the set values.

Forward
starting Sets the forward starting
torque 0.0 to
C4-03 torque as a percentage of the 0.0% No No No A No No 217H -
200.0
motor rated torque.
正转起动
转矩量

Reverse
starting Sets the reverse starting
torque -200.0
C4-04 torque as a percentage of the 0.0% No No No A No No 218H -
to 0.0
motor rated torque.
反转起动
转矩量

Starting
torque time Sets the delay time in ms for
constant starting torque. The filter is 0 to
C4-05 10 ms No No No A No No 219H -
disabled if the time is set to 0 200
起动转矩时 to 4 ms.
间

* The factory setting will change when the control method is changed. The open-loop vector 1 factory settings are given.

5-24
 User Constant Tables

„Speed Control (ASR): C5

User constants for speed control are shown in the following table.
Name Control Methods
Con- Change Open Open MEMO-
Fac-
stant Setting during BUS
Num-
Description Range
tory
Opera-
V/f Loop Flux Loop Page
Display Setting V/f with Vec- Vec- Vec- Regis-
ber tion PG tor tor tor ter
1 2

ASR pro-
portional 0.00 to
Sets the proportional gain of the speed 20.00 4-19
C5-01 (P) gain 1 300.00 Yes No A No A A 21BH
loop (ASR.) *1 6-136
*2
比例增益 1

ASR inte-
gral (I) 0.000 0.500
Sets the integral time of the speed loop 4-19
C5-02 time 1 to s Yes No A No A A 21CH
(ASR) in 1-second units. 6-136
10.000 *1
积分时间 1

ASR pro-
portional Usually setting is not necessary. 0.00 to
20.00 4-19
C5-03 (P) gain 2 Set to change the rotational speed gain. 300.00 *1
Yes No A No A A 21DH
6-136
2
P, I *
比例增益 2 P=C5-01
I=C5-02
ASR inte-
P=C5-03
gral (I) 0.000 0.500
I=C5-04 4-19
C5-04 time 2 to s Yes No A No A A 21EH
0 E1-04 Motor speed (Hz) 6-136
10.000 *1
积分时间 2

ASR limit Sets the upper limit for the compensa-

tion frequency for the speed control 0.0 to
C5-05 5.0% No No A No No No 21FH 6-137
ASR 极限 loop (ASR) to a percentage of the 20.0
maximum output frequency.

ASR pri- Sets the filter time constant for output-

mary delay ting torque references from the speed
time control loop (ASR). It is set in 1-sec-
0.000 0.004
ond units. 4-19
C5-06 to s No No No No A A 220H
With open-loop vector 2 control, this 6-137
ASR 延迟时
0.500 *1
setting is enabled only for speeds in
间 the range 0 to 35 Hz.
Usually setting is not necessary.
ASR
switching Set the frequency for switching
0.0 to 0.0 4-19
C5-07 frequency between Proportion Gain 1, 2 and Inte- No No No No A A 221H
400.0 Hz 6-137
增益切换频
gral Time 1, 2 in Hz units.
率

ASR inte-
gral (I) Set to a small value to prevent any rad-
0 to
C5-08 limit ical load change. Set to 100% of the 400% No No No No A A 222H 6-137
400
maximum output frequency.
积分极限

ASR pri- Sets the filter time constant for output-

mary delay ting torque references from the speed
time 2 control loop (ASR). It is set in 1-sec-
0.000 4-20
ond units. 0.010
C5-10 to No No No No No A 231H 6-137
With open-loop vector 2 control, this s
ASR 延迟时
0.500 6-141
setting is enabled only for speeds
间2 greater than 35 Hz.
Usually setting is not necessary.
* 1. When the control method is changed, the factory settings will change. The flux vector factory settings are given. Refer to Factory Settings that Change
with the Control Method (A1-02).
* 2. The setting range for flux vector and open-loop vector 2 controls is 1.00 to 300.00.

5-25
 „Carrier Frequency: C6
User constants for the carrier frequency are shown in the following table.
Name Control Methods
Con- Change MEMO-
Fac- Open Open
stant Setting during BUS
Num-
Description Range
tory
Opera-
V/f Loop Flux Loop
Regis-
Page
Display Setting V/f with Vec- Vec- Vec-
ber tion PG tor tor tor ter
1 2

Carrier fre-
quency Select carrier wave fixed pattern. 4-6
1 to F 6 No
C6-02 selection Select F to enable detailed settings No Q Q Q Q 224H 4-18
*2 *1 *4
载波频率选
using constants C6-03 to C6-07. 6-42
择

Carrier Set the carrier frequency upper limit and

frequency lower limit in kHz units. 2.0 to
15.0
C6-03 upper limit The carrier frequency gain is set as fol- 15.0
kHz No A A A A No 225H 6-42
*3 lows: *2 *5
*1
载波频率上 *6
With the vector control method, the
限
upper limit of the carrier frequency is
Carrier fixed in C6-03.
frequency 0.4 to 15.0
C6-04 lower limit
15.0 kHz No A A No No No 226H 6-42
*3
*2 *5 *1
载波频率下
Carrier frequency
限

Carrier fre-
quency
Output frequency x (C6-05) x K
propor-
Output
tional gain frequency

C6-05
(Max. output frequency)
00 to
00 No A A No No No 227H 6-42
*3
K is a coefficient that depends on the 99
载波频率比 setting of C6-03.
例增益 C6-03 ≥ 10.0 kHz: K = 3
10.0 kHz > C6-03 ≥ 5.0 kHz: K = 2
5.0 kHz > C6-03: K = 1

Carrier fre-
quency
selection Select the carrier frequency when open-
for open- loop vector 2 control is used.
4-6
loop vec- 1: 2 kHz 1 No No No No
C6-11 1 to 4 No Q 22DH 4-20
tor 2 con- 2: 4 kHz *1 *4 *4 *4 *4
6-42
trol 3: 6 kHz
4: 8 kHz
无 PG 矢量
2 载波

* 1. The factory settings depend on the capacity of the Inverter. The values for a 200 V Class Inverter for 0.4 kW are given.
* 2. The setting ranges depend on the capacity of the Inverter. The values for a 200 V Class Inverter for 0.4 kW are given.
* 3. This constant can be monitored or set only when F is set for C6-02.
* 4. Displayed in Quick Programming Mode when motor 2 is set for a multi-function input.
* 5. The maximum output frequency depends on the setting for the carrier frequency (refer to page 6-43).
* 6. The factory setting for 400V 132kW and 220kW flax vector control (A1-02 = 3) is 1.5 kHz, for software version VSG123032 or later.

5-26
 User Constant Tables

‹ d: Reference Constants
The following settings are made with the reference constants (d constants): Frequency references.

„Preset Reference: d1
User constants for frequency references are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Frequency
reference 1 Sets the frequency reference 4-6
d1-01 0.00 Hz Yes Q Q Q Q Q 280H
in the units used in o1-03. 6-5
频率指令 1

Frequency The frequency reference

reference 2 when multi-step speed refer- 4-6
d1-02 0.00 Hz Yes Q Q Q Q Q 281H
ence 1 is ON for a multi-func- 6-5
频率指令 2 tion input.

Frequency The frequency reference

reference 3 when multi-step speed refer- 4-6
d1-03 0.00 Hz Yes Q Q Q Q Q 282H
ence 2 is ON for a multi-func- 6-5
频率指令 3 tion input.

Frequency The frequency reference

reference 4 when multi-step speed refer- 4-6
d1-04 0.00 Hz Yes Q Q Q Q Q 283H
ences 1 and 2 are ON for 6-5
频率指令 4 multi-function inputs.

Frequency The frequency when multi-

d1-05 reference 5 step speed reference 3 is ON 0.00 Hz Yes A A A A A 284H 6-5
频率指令 5 for a multi-function input.

Frequency The frequency reference

reference 6 when multi-step speed refer- 0 to
d1-06 0.00 Hz Yes A A A A A 285H 6-5
ences 1 and 3 are ON for 400.00
频率指令 6 multi-function inputs. *

Frequency The frequency reference

reference 7 when multi-step speed refer-
d1-07 0.00 Hz Yes A A A A A 286H 6-5
ences 2 and 3 are ON for
频率指令 7 multi-function inputs.
Frequency The frequency reference
reference 8 when multi-step speed refer-
d1-08 0.00 Hz Yes A A A A A 287H 6-5
ences 1, 2, and 3 are ON for
频率指令 8 multi-function inputs.

Frequency The frequency reference

reference 9 when multi-step speed refer-
d1-09 0.00 Hz Yes A A A A A 288H -
ence 4 is ON for a multi-func-
频率指令 9 tion input.

Frequency The frequency reference

reference 10 when multi-step speed refer-
d1-10 0.00 Hz Yes A A A A A 28BH -
ences 1 and 4 are ON for
频率指令 10 multi-function inputs.
Frequency The frequency reference
reference 11 when multi-step speed refer-
d1-11 0.00 Hz Yes A A A A A 28CH -
ences 2 and 4 are ON for a
频率指令 11 multi-function inputs.

5-27
 Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Frequency The frequency reference
reference 12 when multi-step speed refer-
d1-12 0.00 Hz Yes A A A A A 28DH -
ences 1, 2, and 4 are ON for
频率指令 12 multi-function inputs.

Frequency The frequency reference

reference 13 when multi-step speed refer-
d1-13 0.00 Hz Yes A A A A A 28EH -
ences 3 and 4 are ON for
频率指令 13 multi-function inputs.

Frequency The frequency reference

reference 14 when multi-step speed refer-
d1-14 0.00 Hz Yes A A A A A 28FH -
ences 1, 3, and 4 are ON for
频率指令 14 multi-function inputs. 0 to
Frequency The frequency reference 400.00
*
reference 15 when multi-step speed refer-
d1-15 0.00 Hz Yes A A A A A 290H -
ences 2, 3, and 4 are ON for
频率指令 15 multi-function inputs.

Frequency The frequency reference

reference 16 when multi-step speed refer-
d1-16 0.00 Hz Yes A A A A A 291H -
ences 1, 2, 3, and 4 are ON
频率指令 16 for multi-function inputs.

Jog frequency The frequency reference

reference when the jog frequency refer- 4-6
d1-17 ence selection, FJOG com- 6.00 Hz Yes Q Q Q Q Q 292H 6-5
点动频率上限 mand, or RJOG command is 6-84
ON.
Note The unit is set in o1-03 (Frequency units of reference setting and monitor). The default for o1-03 is 0 (increments of 0.01 Hz).
* The setting range for open-loop vector 2 control is 0 to 132.0.

„Reference Limits: d2
User constants for frequency reference limits are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Frequency Set the output frequency
reference upper limit as a percent, tak- 0.0 to 6-34
d2-01 upper limit 100.0% No A A A A A 289H
ing the max. output frequency 110.0 6-79
频率指令上限 to be 100%.

Frequency Sets the output frequency

reference lower limit as a percentage of 0.0 to 6-34
d2-02 lower limit 0.0% No A A A A A 28AH
the maximum output fre- 110.0 6-79
频率指令下限 quency.

Master speed Set the master speed refer-

reference ence lower limit as a percent, 0.0 to 6-34
d2-03 lower limit 0.0% No A A A A A 293H
taking the max. output fre- 110.0 6-79
主速指令下限 quency to be 100%.

5-28
 User Constant Tables

„Jump Frequencies: d3
User constants for jump frequencies are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Jump fre- Set the center values of the
quency 1 jump frequencies in Hz. 4-21
d3-01 0.0 Hz No A A A A A 294H
This function is disabled by 6-31
禁止频率 1
setting the jump frequency to
Jump fre- 0 Hz. Always ensure that the
quency 2 following applies: 0.0 to 4-21
d3-02 0.0 Hz No A A A A A 295H
d3-01 ≥ d3-02 ≥ d3-03 400.0 6-31
禁止频率 2 Operation in the jump fre-
quency range is prohibited
Jump fre-
but during acceleration and 4-21
d3-03 quency 3 0.0 Hz No A A A A A 296H
deceleration, speed changes 6-31
禁止频率 3 smoothly without jump.

Jump fre- Sets the jump frequency

quency width bandwidth in Hz. 0.0 to 4-21
d3-04 1.0 Hz No A A A A A 297H
The jump frequency will be 20.0 6-31
禁止频率幅度 the jump frequency ± d3-04.

„Reference Frequency Hold: d4

User constants for the reference frequency hold function are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Frequency Sets whether or not frequen-
reference cies on hold will be recorded.
hold function 0: Disabled (when operation
selection is stopped or the power is
turned on again starts at
0.)
1: Enabled (when operation
is stopped or the power is
d4-01 0 or 1 0 No A A A A A 298H 6-78
turned on again starts at
the previous hold
频率保持功能 frequency.)
This function is available
when the multi-function
inputs “accel/decel Ramp
Hold” or “up/down” com-
mands are set.

+ - Speed Set the frequency to be added

limits to or subtracted from the ana-
log frequency reference as a
percent, taking the maximum
output frequency to be 100%. 0 to
d4-02 10% No A A A A A 299H 6-82
+ - 加减速极
Enabled when the increase 100
限 (+) speed command or
decrease (-) speed command
is set for a multi-function
input.

5-29
 „Torque Control: d5
User constants for the torque control are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Torque con- 0: Speed control (C5-01 to
trol selection C5-07)
1: Torque control
This function is only avail-
able in flux vector control
d5-01 method. To use the function 0 or 1 0 No No No No A A 29AH 6-127
转矩控制选择 for switching between speed
and torque control, set to 0
and set the multi-function
input to “speed/torque control
change.”

Torque Set the torque reference delay

reference time in ms units.
delay time This function can be used to
adjust the noise of the torque
0 to
d5-02 control signal or the respon-
1000 0* No No No No A A 29BH 6-127
siveness with the host con-
转矩控制延迟
时间 troller. When oscillation
occurs during torque control,
increase the set value.

Speed limit Set the speed limit command

selection method for the torque control
method.
1: The analog input limit
d5-03 1 or 2 1 No No No No A A 29CH 6-127
from a frequency refer-
速度极限选择 ence
2: Limited by d5-04 constant
setting values.
Speed limit Set the speed limit during
torque control as a percentage
of the maximum output fre-
quency.
This function is enabled when -120 to
d5-04 0 No No No No A A 29DH 6-127
速度极限 d5-03 is set to 2. Directions +120
are as follows.
+: Run Command direction
-: Run Command opposite
direction
Speed limit Set the speed limit bias as a
bias percentage of the maximum
output frequency.
0 to
d5-05 Bias is given to the specified 10 No No No No A A 29EH 6-127
120
速度极限偏置 speed limit. It can be used to
adjust the margin for the
speed limit.

5-30
 User Constant Tables

Name Control Methods

Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Speed/torque Set the delay time from input-
control ting the multi-function input
switching “speed/torque control
timer change” (from On to OFF or
OFF to ON) until the control
is actually changed, in ms
units.
This function is enabled when
the multi-function input 0 to
d5-06 0 No No No No A A 29FH 6-128
“speed/torque control 1000
change” is set. In the speed/
控制切换时间 torque control switching
timer, the analog inputs hold
the values of when the
“speed/torque control
change” changes. Always be
sure to allow time for this
process to finish completely.
Rotation 0: Disabled
direction 1: Enabled
limit Usually, use a setting of 1
operation (enabled).
d5-07 selection Be sure to enable this setting 0 or 1 1 No No No No No A 2A6H 6-128
when rotating the motor in
the same direction as the
旋转方向限制
动作 speed limit (winding opera-
tion).
* The factory setting will change when the control method is changed. The flux vector factory setting is given.

„Field Weakening: d6
User constants for the field weakening command are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Field weak- Set the Inverter output volt-
ening level age when the field weakening
command is input.
It is enabled when the field
0 to
d6-01 weakening command is set 80% No A A No No No 2A0H -
100
弱励磁值 for a multi-function input.
Set the level as a percentage
taking the voltage set in the
V/f pattern as 100%.

Field Set the lower limit in hertz of

frequency the frequency range where
field control is valid.
The field weakening com-
0.0 to
d6-02 mand is valid only at frequen- 0.0 Hz No A A No No No 2A1H -
400.0
励磁频率 cies above this setting and
only when the speed is in
agreement with the current
speed reference.

5-31
 Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Field forcing
function Set the field forcing function.
d6-03 selection 0: Disabled 0 or 1 0 No No No A A A 2A2H -
1: Enabled
励磁增强功能

AφR time Set the factor to multiple

constant times the secondary circuit
time constant of the motor to
achieve the AφR time
constant.
AφR time constant =
0.00 to
d6-05 Secondary circuit time 1.00 No No No No No A 2A4H -
10.00
励磁控制时间 constant x d6-05
参数 AφR will not function when
d6-05 is 0. If d6-05 is not 0,
the lower limit of the value
will be internally adjusted to
200 ms in the Inverter.

Field forcing Set the excitation current ref-

limit erence’s upper limit for field
forcing. Set the limit as a per-
centage, taking the motor’s
100 to
d6-06 no-load current as 100%. 400% No No No A A A 2A5H -
400
励磁增强极限 Enabled for operation other
than DC excitation.
Usually, there is no need to
change this setting.

5-32
 User Constant Tables

‹ E: Motor Constant Constants

The following settings are made with the motor constant constants (E constants): V/f characteristics and motor
constants.

„V/f Pattern: E1
User constants for V/f characteristics are shown in the following table.
Name Control Methods
Con- Change Open Open MEMO-
stant Setting Factory during BUS
Num-
Description Range Setting Opera-
V/f Loop Flux Loop
Regis-
Page
Display V/f with Vec- Vec- Vec-
ber tion PG tor tor tor ter
1 2

Input volt- Set the Inverter input voltage in 1

155 to
age setting volt. 200 V 4-5
E1-01 255 No Q Q Q Q Q 300H
This setting is used as a reference *1 6-120
*1
输入电压 value in protection functions.

V/f pattern 0 to E: Select from the 15 preset

selection patterns.
E1-03 F: Custom user-set patterns 0 to F F No Q Q No No No 302H 6-120
V/F 曲线设 (Applicable for settings E1-04
定 to E1-10.)

Max.
output 40.0 to 50.0
E1-04 frequency 400.0 Hz No Q Q Q Q Q 303H 6-120
*5 *2
最高输出频
率

Max. 0.0 to 200.0

E1-05 voltage 255.0 V No Q Q Q Q Q 304H 6-120
*1 *1*2
最大电压 Output voltage (V)
VMAX
Base (E1-05)
(V BASE) 0.0 to 50.0
E1-06 frequency (E1-13)
400.0 Hz No Q Q Q Q Q 305H 6-120
VC
(E1-08) *5 *2
基本频率
VMIN
(E1-10)
Mid. output FMIN FB FA FMAX
frequency (E1-09) (E1-07) (E1-06) (E1-04) 0.0 to 3.0 Hz
E1-07 Frequency (Hz) No A A A No No 306H 6-120
400.0 *2
中间频率 To set V/f characteristics in a
straight line, set the same values for
Mid. output
E1-07 and E1-09. In this case, the
frequency 0.0 to
setting for E1-08 will be disre- 13.2 V 4-18
E1-08 voltage 255.0 No A A A No No 307H
garded. *1 *2 6-120
*1
中间电压 Always ensure that the four fre-
quencies are set in the following
Min. output manner:
frequency E1-04 (FMAX) ≥ E1-06 (FA) > E1- 0.0 to
0.5 Hz
E1-09 400.0 No Q Q Q A Q 308H 6-120
最低输出频
07 (FB) ≥ E1-09 (FMIN) *2
*5
率

Min. output
frequency 0.0 to
voltage 2.4 V 4-18
E1-10 255.0 No A A A No No 309H
*1 *2 6-120
*1
最低输出电
压

5-33
 Name Control Methods
Con- Change Open Open MEMO-
stant Setting Factory during BUS
Num-
Description Range Setting Opera-
V/f Loop Flux Loop Page
Display V/f with Vec- Vec- Vec- Regis-
ber tion PG tor tor tor ter
1 2

Mid. output 0.0 to

frequency 2 0.0 Hz
E1-11 400.0 No A A A A A 30AH 6-120
*3
*5
中间频率 2

Mid. output
frequency Set only to fine-adjust V/f for the 0.0 to
0.0 V
E1-12 voltage 2 output range. Normally, this setting 255.0 No A A A A A 30BH 6-120
*3
is not required. *1
中间电压 2

Base 0.0 to
voltage 0.0 V
E1-13 255.0 No A A Q Q Q 30CH 6-120
*4
*1
基本电压

* 1. These are values for a 200 V Class Inverter. Values for a 400 V Class Inverter are double.
* 2. The factory setting will change when the control method is changed. The open-loop vector 1 factory settings are given.
* 3. E1-11 and E1-12 are disregarded when set to 0.0.
* 4. E1-13 is set to the same value as E1-05 by autotuning.
* 5. The setting range for open-loop vector 2 control is 0 to 132.0.

„Motor Setup: E2
User constants for motor 1 are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Motor rated Sets the motor rated current in
current 1 A units.
These set values will become
0.32 to 4-5
the reference values for motor 1.90 A
E2-01 6.40 No Q Q Q Q Q 30EH 6-57
protection, torque limits and *1
电机额定电流 *2 6-117
torque control.
This constant is automatically
set during autotuning.
Motor rated Sets the motor rated slip in
slip Hz units.
These set values will become
0.00 to 2.90 Hz 6-115
E2-02 the reference values for slip No A A A A A 30FH 6-117
20.00 *1
电机额定滑差 compensation.
This constant is automatically
set during autotuning.
Motor no- Sets the motor no-load cur-
0.00 to
load current rent in 1 A units. 1.20 A
E2-03 1.89 No A A A A A 310H 6-117
This constant is automatically *1
空载电流 *3
set during autotuning.
Number of Sets the number of motor
motor poles poles.
E2-04 2 to 48 4 poles No No Q No Q Q 311H 6-117
This constant is automatically
电机极数
set during autotuning.
Motor line- Sets the motor phase-to-phase
to-line resis- 0.000 9.842
resistance in Ω units.
E2-05 tance to Ω No A A A A A 312H 6-117
This constant is automatically
65.000 *1
线间电阻 set during autotuning.
Motor leak Sets the voltage drop due to
inductance motor leakage inductance as a
percentage of the motor rated 0.0 to 18.2%
E2-06 No No No A A A 313H 6-117
voltage. 40.0 *1
电机漏电感
This constant is automatically
set during autotuning.

5-34
 User Constant Tables

Name Control Methods

Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Motor iron Sets the motor iron saturation
saturation coefficient at 50% of mag-
0.00 to
E2-07 coefficient 1 netic flux. 0.50 No No No A A A 314H 6-117
0.50
This constant is automatically
饱和系数 1
set during autotuning.
Motor iron Sets the motor iron saturation
saturation coefficient at 75% of mag-
0.00 to
E2-08 coefficient 2 netic flux. 0.75 No No No A A A 315H 6-117
0.75
This constant is automatically
饱和系数 2
set during autotuning.
Motor Sets motor mechanical loss as
mechanical a percentage of motor rated
loss output (W).
Usually setting is not neces-
sary.
Adjust in the following cir-
0.0 to
E2-09 cumstances: 0.0 No No No A A A 316H -
10.0
• When torque loss is large
due to motor bearing.
机械损失 • When the torque loss in the
pump or fan is large.
The set mechanical loss will
compensate for torque.
Motor iron
loss for
torque com- Sets motor iron loss in W 0 to 14 W
E2-10 No A A No No No 317H 6-117
pensation units. 65535 *1

铁损
Motor rated Set the rated output of the
output motor in units of 0.01 kW. 0.00 to 0.40
E2-11 No Q Q Q Q Q 318H 6-115
This constant is automatically 650.00 *4
电机额定功率
set during autotuning.
Motor iron Sets the motor iron saturation
saturation coefficient at 130% of mag-
1.30 to
E2-12 coefficient 3 netic flux. 1.30 No No No A A A 328H 6-118
1.60
This constant is automatically
饱和系数 3
set during autotuning.
* 1. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given.
* 2. The setting range is from 10% to 200% of the Inverter rated output current. The value for a 200 V Class Inverter for 0.4 kW is given.
For the motor no-load current, set E2-03 to a value less than that of E2-01.
* 3. The setting range depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. The upper limit depends on the setting of
E2-01.
* 4. The same capacity as that of the Inverter will be set if the constants are initialized.

5-35
 „ Motor 2 V/f Pattern: E3
User constants for motor 2 V/f characteristics are shown in the following table.
Name Control Methods
Con- Change Open Open MEMO-
stant Setting Factory during BUS
Num-
Description Range Setting Opera-
V/f Loop Flux Loop Page
Display V/f with Vec- Vec- Vec- Regis-
ber tion PG tor tor tor ter
1 2

Motor 2 0: V/f control

control 1: V/f control with PG
E3-01 method 2: Open-loop vector control 0 to 4 2 No A A A A A 319H -
selection 3: Flux vector control
控制模式
4: Open-loop vector 2 control

Motor 2
max. out-
put fre- 40.0 to
50.0
E3-02 quency 400.0 No A A A A A 31AH -
Hz
(FMAX) *3

最高频率

Motor 2
max. volt- 0.0 to 200.0
E3-03 age 255.0 V No A A A A A 31BH -
(VMAX) *1 *2

最大电压

Motor 2
max. volt-
age fre- 0.0 to 50.0
E3-04 quency No A A A A A 31CH -
Output voltage (V) 400.0 Hz
(FA) VMAX
E3-03

基本频率

Motor 2 VC
mid. out- E3-06

put fre- VMIN

0.0 to 3.0 Hz
E3-05 quency 1
E3-08
No A A A No No 31DH -
FMIN FB FA FMAX 400.0 *2
(FB) E3-07 E3-05 E3-04 E3-02

中间频率 Frequency (Hz)

Motor 2
mid. out- To set V/f characteristics in a
put fre- straight line, set the same values for
E3-05 and E3-07. 0.0 to
quency 13.2 V
E3-06 In this case, the setting for E3-06 255.0 No A A A No No 31EH -
voltage 1 *1
*1
(VC) will be disregarded.
Always ensure that the four frequen-
中间电压 cies are set in the following manner:
E3-02 (FMAX) ≥ E3-04 (FA) > E3-
Motor 2
05 (FB) > E3-07 (FMIN)
min. out-
put fre-
quency 0.0 to 0.5 Hz
E3-07 No A A A A A 31FH -
(FMIN) 400.0 *2

最低输出频
率

Motor 2
min. out-
put fre-
quency 0.0 to
2.4 V
E3-08 voltage 255.0 No A A A No No 320H -
*1
*1
(VMIN)

最低输出电
压

* 1. These are values for a 200 V Class Inverter. Values for a 400 V Class Inverter are double.
* 2. The factory setting will change when the control method is changed. The open-loop vector 1 factory settings are given.
* 3. The setting range for open-loop vector 2 control is 0 to 132.0.

5-36
 User Constant Tables

„Motor 2 Setup: E4
User constants for motor 2 are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Motor 2 rated Sets the motor rated current in
current 1 A units.
These set values will become
0.32
the reference values for motor 1.90 A
E4-01 to 6.40 No A A A A A 321H 6-57
protection, torque limits and *1
*2
电机额定电流 torque control.
This constant is automatically
set during autotuning.

Motor 2 rated Sets the motor rated slip in

slip Hz units.
These set values will become
0.00 to 2.90 Hz
E4-02 the reference values for slip No A A A A A 322H -
电机 2 额定滑 compensation.
20.00 *1

差 This constant is automatically

set during autotuning.

Motor 2 no- Sets the motor no-load cur-

load current 0.00 to
rent in 1 A units. 1.20 A
E4-03 1.89 No A A A A A 323H -
电机 2 空载电
This constant is automatically *1
*3
流 set during autotuning.

Motor 2 num-
ber of poles Sets the number of motor
(number of poles.
E4-04 2 to 48 4 poles No No A No A A 324H -
poles) This constant is automatically
set during autotuning.
电机 2 极数

Motor 2 line-
to-line resis- Sets the motor phase-to-phase
0.000 9.842
tance resistance in Ω units.
E4-05 to Ω No A A A A A 325H -
This constant is automatically
电机 2 线间电
65.000 *1
set during autotuning.
阻

Motor 2 leak Sets the voltage drop due to

inductance motor leakage inductance as a
percentage of the motor rated 0.0 to 18.2%
E4-06 No No No A A A 326H -
voltage. 40.0 *1
电机 2 漏电感 This constant is automatically
set during autotuning.

Motor 2 rated Set the rated output of the

capacity motor in units of 0.01 kW. 0.00 to 0.40
E4-07 No A A A A A 327H -
电机 2 额定容
This constant is automatically 650.00 *4

量 set during autotuning.

* 1. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given.
* 2. The setting range is from 10% to 200% of the Inverter rated output current. The value for a 200 V Class Inverter for 0.4 kW is given.
* 3. If a multi-function input is set for motor 2 (H1-†† = 16), the setting range will depend upon the Inverter capacity. The value for a 200 V Class Inverter
of 0.4 kW is given. The upper limit depends on the setting of E4-01.
* 4. The same capacity as that of the Inverter will be set if the constants are initialized.

5-37
 ‹ F: Option Constants
The following settings are made with the option constants (F constants): Settings for option boards

„PG Option Setup: F1

User constants for the PG Speed Control Board are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
PG constant Sets the number of PG (pulse
generator or encoder) pulses. 0 to
F1-01 600 No No Q No Q No 380H 6-158
PG 脉冲数 Sets the number of pulses per 60000
motor revolution.

Operation Sets the PG disconnection

selection at stopping method.
PG open cir- 0: Ramp to stop
cuit (PGO) (Deceleration stop using
Deceleration Time 1, C1-
02.)
1: Coast to stop
F1-02 2: Fast stop (Emergency stop 0 to 3 1 No No A No A No 381H 6-158
using the deceleration
PG 动作选择 time in C1-09.)
3: Continue operation (To
protect the motor or
machinery, do not
normally make this
setting.)

Operation Sets the stopping method

selection at when an overspeed (OS) fault
overspeed occurs.
(OS) 0: Ramp to stop
(Deceleration stop using
Deceleration Time 1, C1-
02.)
1: Coast to stop
F1-03 0 to 3 1 No No A No A A 382H 6-158
2: Fast stop (Emergency stop
using the deceleration
OS 动作选择 time in C1-09.)
3: Continue operation (To
protect the motor or
machinery, do not
normally make this
setting.)

Operation Sets the stopping method

selection at when a speed deviation
deviation (DEV) fault occurs.
0: Ramp to stop
(Deceleration stop using
Deceleration Time 1, C1-
02.)
F1-04 0 to 3 3 No No A No A A 383H 6-158
1: Coast to stop
DEV 动作选择 2: Fast stop (Emergency stop
using the deceleration
time in C1-09.)
3: Continue operation (DEV
is displayed and operation
continued.)

5-38
 User Constant Tables

Name Control Methods

Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
PG rotation 0: Phase A leads with
Forward Run Command.
(Phase B leads with
Reverse Run Command.)
F1-05 0 or 1 0 No No A No A No 384H 6-158
PG 方向设定 1: Phase B leads with
Forward Run Command.
(Phase A leads with
Reverse Run Command.)

PG division Sets the division ratio for the

rate (PG PG speed control board pulse
pulse moni- output.
tor) Division ratio = (1+ n) /m
(n=0 or 1 m=1 to 32)
1 to
F1-06 F1-06 1 No No A No A No 385H 6-159
132
n m
PG 输出分频比 This constant is only effective
when a PG-B2 is used.
The possible division ratio
settings are: 1/32 ≤ F1-06 ≤ 1.

Integral value Sets integral control during

during accel/ acceleration/deceleration to
decel enable/ either enabled or disabled.
disable 0: Disabled (The integral
function isn't used while
F1-07 accelerating or 0 or 1 0 No No A No No No 386H 6-159
decelerating; it is used at
积分动作选择 constant speeds.)
1: Enabled (The integral
function is used at all
times.)

Overspeed
detection Sets the overspeed detection
0 to
F1-08 level method. 115% No No A No A A 387H 6-159
120
Frequencies above that set for
过速检出值 F1-08 (set as a percentage of
the maximum output fre-
Overspeed
detection quency) that continue to
exceed this frequency for the 0.0 to 0.0 s
F1-09 delay time No No A No A A 388H 6-159
time set in F1-09 are detected 2.0 *
OS 过速检出 as overspeed faults.
时间

Excessive
Sets the speed deviation
speed devia-
detection method.
F1-10 tion detec- 0 to 50 10% No No A No A A 389H 6-159
Any speed deviation above
tion level
the F1-10 set level (set as a
DEV 检出值 l percentage of the maximum
output frequency) that contin-
Excessive ues for the time set in F1-11 is
speed devia- detected as a speed deviation.
tion detec- Speed deviation is the differ- 0.0 to
F1-11 tion delay ence between actual motor 0.5 s No No A No A A 38AH 6-159
10.0
time speed and the reference com-
mand speed.
DEV 检出时间

5-39
 Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Number of Sets the number of teeth on
PG gear teeth the gears if there are gears
F1-12 1 between the PG and the 0 No No A No No No 38BH 6-159
motor.
PG 齿轮齿数 1
0 to
Input pulses from PG 60 F1-13
Number of 1000
F1-01 F1-12
PG gear teeth
F1-13 2 A gear ratio of 1 will be used 0 No No A No No No 38CH 6-159
if either of these constants is
PG 齿轮齿数 2 set to 0.

PG open-cir- Used to set the PG disconnec-

cuit detection tion detection time. PGO will
0.0 to
F1-14 time be detected if the detection 2.0 s No No A No A No 38DH 6-159
10.0
time continues beyond the set
PGO 检出时间 time.
* When the control method is changed, the factory setting will change. The flux vector factory setting is given.

„Analog Reference Board: F2

User constants for the Analog Reference Board are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Bi-polar or
Sets the functions for channel
uni-polar 1 to 3 which are effective
input selec-
when the AI-14B Analog
tion Reference Board is used.
0: 3-channel individual
(Channel 1: terminal A1,
Channel 2: terminal A2,
Channel 3: terminal A3)
F2-01 0 or 1 0 No A A A A A 38FH 6-165
1: 3-channel addition (Addi-
tion values are the fre-
AI14 动作选择 quency reference)
When set to 0, select 1 for b1-
01. In this case the multi-
function input “Option/
Inverter selection” cannot be
used.

5-40
 User Constant Tables

„Digital Reference Board: F3

User constants for the Digital Reference Board are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Digital input Sets the Digital Reference
option Board input method.
0: BCD 1% unit
1: BCD 0.1% unit
2: BCD 0.01% unit
3: BCD 1 Hz unit
4: BCD 0.1 Hz unit
5: BCD 0.01 Hz unit
F3-01 6: BCD special setting (5- 0 to 7 0 No A A A A A 390H 6-165
DI 输入选择 digit input)
7: Binary input
6 is only effective when the
DI-16H2 is used.
When o1-03 is set to 2 or
higher, the input will be BCD,
and the units will change to
the o1-03 setting.

5-41
 „Analog Monitor Boards: F4
User constants for the Analog Monitor Board are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Channel 1 Effective when the Analog
monitor Monitor Board is used.
F4-01 selection Monitor selection: 1 to 50 2 No A A A A A 391H 6-89
Set the number of the monitor
CH1 输出监视
item to be output. (U1-††)
Channel 1 Gain:
gain Set the multiple of 10 V for 0.00 to
F4-02 1.00 Yes A A A A A 392H 6-89
outputting monitor items. 2.50
CH1 输出增益 4, 10 to 14, 25, 28, 34, 39, 40
cannot be set. 29 to 31 and 41
Channel 2
are not used. When the AO-
monitor
F4-03 12 Analog Monitor Board is 1 to 50 3 No A A A A A 393H 6-89
selection
used, outputs of ± 10 V are
CH2 输出监视 possible. To output ± 10 V, set
F4-07 or F4-08 to 1. When
Channel 2 the AO-08 Analog Monitor
gain Board is used, only outputs of 0.00 to
F4-04 0 to +10 V are possible. 0.50 Yes A A A A A 394H 6-89
2.50
CH2 输出增益 A meter calibration function
is available.

Channel 1
output moni- Sets the channel 1 item bias
-10.0 to
F4-05 tor bias to 100%/10 V when the Ana- 0.0 Yes A A A A A 395H 6-89
10.0
log Monitor Board is used.
AO CH1 偏置

Channel 2
output moni- Sets the channel 2 item bias
-10.0 to
F4-06 tor bias to 100%/10 V when the Ana- 0.0 Yes A A A A A 396H 6-89
10.0
log Monitor Board is used.
AO CH2 偏置

Analog out-
put signal
level for 0: 0 to 10 V
F4-07 0 or 1 0 No A A A A A 397H 6-89
channel 1 1: -10 to +10 V

CH1 信号电平

Analog out-
put signal
level for 0: 0 to 10 V
F4-08 0 or 1 0 No A A A A A 398H 6-89
channel 2 1: -10 to +10 V

CH2 信号电平

5-42
 User Constant Tables

„Digital Output Boards (DO-02C and DO-08): F5

User constants for the Digital Output Board are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Channel 1 Effective when a Digital Out-
output selec- put Board (DO-02C or DO-
F5-01 tion 08) is used. 0 to 37 0 No A A A A A 399H 6-162
Set the number of the multi-
DO CH1 选择 function output to be output.

Channel 2 Effective when a Digital Out-

output selec- put Board (DO-02C or DO-
F5-02 tion 08) is used. 0 to 37 1 No A A A A A 39AH 6-162
Set the number of the multi-
DO CH2 选择 function output to be output.
Channel 3 Effective when a DO-08 Dig-
output selec- ital Output Board is used.
F5-03 tion 0 to 37 2 No A A A A A 39BH 6-162
Set the number of the multi-
DO CH3 选择 function output to be output.

Channel 4 Effective when a DO-08 Dig-

output selec- ital Output Board is used.
F5-04 tion 0 to 37 4 No A A A A A 39CH 6-162
Set the number of the multi-
DO CH4 选择 function output to be output.

Channel 5 Effective when a DO-08 Dig-

output selec- ital Output Board is used.
F5-05 tion 0 to 37 6 No A A A A A 39DH 6-162
Set the number of the multi-
DO CH5 选择 function output to be output.

Channel 6 Effective when a DO-08 Dig-

output selec- ital Output Board is used.
F5-06 tion 0 to 37 37 No A A A A A 39EH 6-162
Set the number of the multi-
DO CH6 选择 function output to be output.

Channel 7 Effective when a DO-08 Dig-

output selec- ital Output Board is used.
F5-07 tion Set the number of the multi- 0 to 37 0F No A A A A A 39FH 6-163
function output to be output.
DO CH7 选择

Channel 8 Effective when a DO-08 Dig-

output selec- ital Output Board is used.
F5-08 tion 0 to 37 0F No A A A A A 3A0H 6-163
Set the number of the multi-
DO CH8 选择 function output to be output.

DO-08 out- Effective when a DO-08 Dig-

put mode ital Output Board is used.
selection Set the output mode.
0: 8-channel individual out-
F5-09 0 to 2 0 No A A A A A 3A1H 6-163
puts
DO-08 选择 1: Binary code output
2: Output according to
F5-01 to F5-08 settings.

5-43
 „Communications Option Boards: F6
User constants for a Communications Option Board are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Operation Set the stopping method for
selection after communications errors.
communica- 0: Deceleration stop using
tions error deceleration time in C1-
02
F6-01 0 to 3 1 No A A A A A 3A2H -
1: Coast to stop
2: Emergency stop using
BUS 检出动作 deceleration time in C1-
09
3: Continue operation
Input level of
external fault
from Com- 0: Always detect
F6-02 munications 0 or 1 0 No A A A A A 3A3H -
1: Detect during operation
Option Board
EF0 检出选择

Stopping 0: Deceleration stop using

method for deceleration time in C1-
external fault 02
from Com- 1: Coast to stop
F6-03 0 to 3 1 No A A A A A 3A4H -
munications 2: Emergency stop using
Option Board deceleration time in C1-
09
EF0 检出 动作 3: Continue operation
Trace sam-
pling from
Communica- 0 to
F6-04 tions Option - 0 No A A A A A 3A5H -
60000
Board
跟踪取样

Torque refer-
ence/torque 0: Torque reference/torque
limit selec- limit from transmission
tion from disabled.
F6-06 0 or 1 0 No No No No A A 3A7H -
optical option 1: Torque reference/torque
limit from transmission
转矩指令及 enabled.
极限

Operation Set the stopping method for

selection after SI-T WDT errors (E5).
SI-T WDT 0: Deceleration stop using
error deceleration time in C1-
02
F6-08 0 to 3 1 No A A A A A 3B6H -
1: Coast to stop
2: Emergency stop using
SI-T WDT deceleration time in C1-
09
3: Continue operation
Number of
SI-T BUS
error detec- Set the number which SI-T
F6-09 2 to 10 2 No A A A A A 3B7H -
tion detects BUS errors.

SI-T BUS

5-44
 User Constant Tables

‹ H: Terminal Function Constants

The following settings are made with the terminal function constants (H constants): Settings for external ter-
minal functions.

„Multi-function Contact Inputs: H1

User constants for multi-function contact inputs are shown in the following tables.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Terminal S3
function selec-
tion Multi-function contact input
H1-01 0 to 79 24 No A A A A A 400H -
1
端子 S3 功能设
定

Terminal S4
function selec- Multi-function contact input
H1-02 tion 0 to 79 14 No A A A A A 401H -
2
端子 S4 设定

Terminal S5
function selec- Multi-function contact input
H1-03 tion 3
0 to 79 3 (0)* No A A A A A 402H -

端子 S5 设定

Terminal S6
function selec- Multi-function contact input
H1-04 tion 4
0 to 79 4 (3)* No A A A A A 403H -

端子 S6 设定

Terminal S7
function selec- Multi-function contact input
H1-05 tion 5
0 to 79 6 (4)* No A A A A A 404H -

端子 S7 设定

Terminal S8
function selec- Multi-function contact input
H1-06 tion 6
0 to 79 8 (6)* No A A A A A 405H -

端子 S8 设定

Terminal S9
function selec- Multi-function contact input
H1-07 tion 0 to 79 5 No A A A A A 406H -
7
端子 S9 设定

Terminal S10
function selec- Multi-function contact input
H1-08 tion 0 to 79 32 No A A A A A 407H -
8
端子 S10 设定

Terminal S11
function selec- Multi-function contact input
H1-09 tion 0 to 79 7 No A A A A A 408H -
9
端子 S11 设定

5-45
 Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Terminal S12
function selec- Multi-function contact input
H1-10 tion 0 to 79 15 No A A A A A 409H -
10
端子 S12 设定

* The factory settings in the parentheses are for 3-wire sequence.

Multi-function Contact Input Functions

Control Methods
Set- Open Open
ting Function V/f Loop Flux Loop Page
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
0 3-wire sequence (Forward/Reverse Run Command) Yes Yes Yes Yes Yes 6-11

1 Local/Remote selection (ON: Local, OFF: Remote) Yes Yes Yes Yes Yes 6-76

6-83
2 Option/Inverter selection (ON: Option board) Yes Yes Yes Yes Yes
6-164

Multi-step speed reference 1

3 When H3-05 is set to 0, this function is combined with the master/auxiliary speed Yes Yes Yes Yes Yes 6-5
switch.

4 Multi-step speed reference 2 Yes Yes Yes Yes Yes 6-5

5 Multi-step speed reference 3 Yes Yes Yes Yes Yes 6-5

6 Jog frequency command (higher priority than multi-step speed reference) Yes Yes Yes Yes Yes 6-5

7 Accel/decel time 1 Yes Yes Yes Yes Yes 6-19

8 External baseblock NO (NO contact: Baseblock at ON) Yes Yes Yes Yes Yes 6-77

9 External baseblock NC (NC contact: Baseblock at OFF) Yes Yes Yes Yes Yes 6-77
Acceleration/deceleration ramp hold (ON: Acceleration/deceleration stopped, fre-
A Yes Yes Yes Yes Yes 6-78
quency on hold)

B OH2 alarm signal input (ON: OH2 will be displayed) Yes Yes Yes Yes Yes -

C Multi-function analog input selection (ON: Enable) Yes Yes Yes Yes Yes -

No V/f control with PG (ON: Speed feedback control disabled,) (normal V/f con-
D No Yes No No No 6-137
trol)

E Speed control integral reset (ON: Integral control disabled) No Yes No Yes Yes 6-137

F Not used (Set when a terminal is not used) - - - - - -

10 Up command (Always set with the down command) Yes Yes Yes Yes Yes 6-79

11 Down command (Always set with the up command) Yes Yes Yes Yes Yes 6-79

12 FJOG command (ON: Forward run at jog frequency d1-17) Yes Yes Yes Yes Yes 6-84

13 RJOG command (ON: Reverse run at jog frequency d1-17) Yes Yes Yes Yes Yes 6-84

14 Fault reset (Reset when turned ON) Yes Yes Yes Yes Yes 7-2

Emergency stop. (Normally open condition: Deceleration to stop in deceleration

15 Yes Yes Yes Yes Yes 6-17
time set in C1-09 when ON.)
16 Motor switch command (Motor 2 selection) Yes Yes Yes Yes Yes -

Emergency stop (Normally closed condition: Deceleration to stop in deceleration

17 Yes Yes Yes Yes Yes 6-17
time set in C1-09 when OFF)
Timer function input (Functions are set in b4-01 and b4-02 and the timer function
18 Yes Yes Yes Yes Yes 6-105
outputs are set in H1-†† and H2-††.)

19 PID control disable (ON: PID control disabled) Yes Yes Yes Yes Yes 6-109

5-46
 User Constant Tables

Control Methods
Set- Open Open
ting Function V/f Loop Flux Loop Page
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
1A Accel/Decel time 2 Yes Yes Yes Yes Yes 6-19

Constants write enable (ON: All constants can be written-in. OFF: All constants 6-156
1B Yes Yes Yes Yes Yes
other than frequency monitor are write protected.) 7-24
Trim control increase (ON: d4-02 frequency is added to analog frequency refer-
1C Yes Yes Yes Yes Yes 6-82
ence.)

Trim control decrease (ON: d4-02 frequency is subtracted from analog frequency
1D Yes Yes Yes Yes Yes 6-82
reference.)

1E Analog frequency reference sample/hold Yes Yes Yes Yes Yes 6-83

20 to External fault (Desired settings possible)

Yes Yes Yes Yes Yes 6-85
2F Input mode: NO contact/NC contact, Detection mode: Normal/during operation

PID control integral reset (reset when reset command is input or when stopped
30 Yes Yes Yes Yes Yes 6-109
during PID control)
31 PID control integral hold (ON: Hold) Yes Yes Yes Yes Yes 6-109

32 Multi-step speed reference 4 Yes Yes Yes Yes Yes -

34 PID soft starter ON/OFF Yes Yes Yes Yes Yes 6-109

35 PID input characteristics switch Yes Yes Yes Yes Yes 6-109

60 DC injection braking command (ON: Performs DC injection braking) Yes Yes Yes Yes Yes 6-16

61 External search command 1 (ON: Speed search from maximum output frequency) Yes No Yes No Yes 6-67
62 External search command 2 (ON: Speed search from set frequency) Yes No Yes No Yes 6-67

Field weakening command (ON: Field weakening control set for d6-01 and d6-
63 Yes Yes No No No -
02)

64 External speed search command 3 (NC contact) Yes Yes Yes Yes Yes -

65 KEB (deceleration at momentary power loss) command (NC contact) Yes Yes Yes Yes Yes -

66 KEB (deceleration at momentary power loss) command (NO contact) Yes Yes Yes Yes Yes -
Communications test mode (“Pass” is displayed when the communications test is
67 Yes Yes Yes Yes Yes 6-104
passed.)

68 High-slip braking (HSB) Yes Yes No No No -

6-129
71 Speed/torque control change (ON: Torque control) No No No Yes Yes
6-135

72 Zero-servo command (ON: Zero-servo) No No No Yes No 6-146

77 Speed control (ASR) proportional gain switch (ON: C5-03) No No No Yes Yes 6-137

78 Polarity reversing command for external torque reference No No No Yes Yes 6-129

79 Brake ON signal (Brake Signal)* No No No No Yes -

* If the multi-function input is set to 79 and the input value is “closed,” operation will be performed with a speed specification of 0.

5-47
 „ Multi-function Contact Outputs: H2
User constants for multi-function outputs are shown in the following tables.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Terminal M1-
M2 function
selection
H2-01 (contact) Multi-function contact output 0 to 3D 0 No A A A A A 40BH -

端子 M1M2
设定

Terminal P1
function
selection Multi-function contact output
H2-02 (open collec- 0 to 3D 1 No A A A A A 40CH -
1
tor)

端子 P1 设定

Terminal P2
function
selection Multi-function contact output
H2-03 (open collec- 0 to 3D 2 No A A A A A 40DH -
2
tor)

端子 P2 设定

Terminal P3
function
selection Multi-function contact output
H2-04 (open collec- 0 to 3D 6 No A A A A A 40EH -
3
tor)

端子 P3 设定

Terminal P4
function
selection Multi-function contact output
H2-05 (open collec- 0 to 3D 10 No A A A A A 40FH -
4
tor)

端子 P4 设定

5-48
 User Constant Tables

Multi-function Contact Output Functions

Control Methods
Set- Open Open
ting Function V/f Loop Flux Loop Page
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
0 During run (ON: Run Command is ON or voltage is being output) Yes Yes Yes Yes Yes 6-86

1 Zero-speed Yes Yes Yes Yes Yes 6-86

2 Frequency agree 1 (L4-02 used.) Yes Yes Yes Yes Yes 6-51

Desired frequency agree 1 (ON: Output frequency = ±L4-01, L4-02 used and dur-
3 Yes Yes Yes Yes Yes 6-51
ing frequency agree)

Frequency (FOUT) detection 1 (ON: +L4-01 ≥ output frequency ≥ -L4-01, L4-02

4 Yes Yes Yes Yes Yes 6-51
used)

Frequency (FOUT) detection 2 (ON: Output frequency ≥ +L4-01 or output fre-

5 Yes Yes Yes Yes Yes 6-51
quency ≤ -L4-01, L4-02 used)
Inverter operation ready
6 Yes Yes Yes Yes Yes -
READY: After initialization, no faults

7 During DC bus undervoltage (UV) detection Yes Yes Yes Yes Yes -

8 During baseblock (ON: during baseblock) Yes Yes Yes Yes Yes -

9 Frequency reference selection (ON: Frequency reference from Operator) Yes Yes Yes Yes Yes -

A Run Command selection status (ON: Run Command from Operator) Yes Yes Yes Yes Yes -
Overtorque/undertorque detection 1 NO (NO contact: Overtorque/undertorque
B Yes Yes Yes Yes Yes 6-54
detection at ON)

C Loss of frequency reference (Effective when 1 is set for L4-05) Yes Yes Yes Yes Yes 6-71
D Braking resistor fault (ON: Resistor overheat or braking transistor fault) Yes Yes Yes Yes Yes 6-74

Fault (ON: Digital Operator communications error or fault other than CPF00 and
E Yes Yes Yes Yes Yes -
CPF01 has occurred.)
F Not used. (Set when the terminals are not used.) - - - - - -

10 Minor fault (ON: Alarm displayed) Yes Yes Yes Yes Yes -

11 Fault reset command active Yes Yes Yes Yes Yes -

12 Timer function output Yes Yes Yes Yes Yes 6-105

13 Frequency agree 2 (L4-04 used) Yes Yes Yes Yes Yes 6-51

Desired frequency agree 2 (ON: Output frequency = L4-03, L4-04 used, and dur-
14 Yes Yes Yes Yes Yes 6-51
ing frequency agree)
15 Frequency detection 3 (ON: Output frequency ≤ -L4-03, L4-04 used) Yes Yes Yes Yes Yes 6-51

16 Frequency detection 4 (ON: Output frequency ≥ -L4-03, L4-04 used) Yes Yes Yes Yes Yes 6-51

17 Overtorque/undertorque detection 1 NC (NC Contact: Torque detection at OFF) Yes Yes Yes Yes Yes 6-54

18 Overtorque/undertorque detection 2 NO (NO Contact: Torque detection at ON) Yes Yes Yes Yes Yes 6-54

19 Overtorque/undertorque detection 2 NC (NC Contact: Torque detection at OFF) Yes Yes Yes Yes Yes 6-54

1A During reverse run (ON: During reverse run) Yes Yes Yes Yes Yes -
1B During baseblock 2 (OFF: During baseblock) Yes Yes Yes Yes Yes -

1C Motor selection (Motor 2 selected) Yes Yes Yes Yes Yes -

1D During regeneration (ON: During regeneration) No No No Yes Yes -

1E Restart enabled (ON: Restart enabled) Yes Yes Yes Yes Yes 6-72

Motor overload (OL1, including OH3) pre-alarm (ON: 90% or more of the detec- 6-58
1F Yes Yes Yes Yes Yes
tion level) 6-87

20 Inverter overheat (OH) pre-alarm (ON: Temperature exceeds L8-02 setting) Yes Yes Yes Yes Yes 6-87

5-49
 Control Methods
Set- Open Open
ting Function V/f Loop Flux Loop Page
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
Maintenance Time
2F ON: The operation time of either the electrolytic capacitors or the cooling fan has Yes Yes Yes Yes Yes -
reached the specified maintenance time.

30 During torque limit (current limit) (ON: During torque limit) No No Yes Yes Yes -

31 During speed limit (ON: During speed limit) No No No Yes No 6-87

Speed control circuit operating for torque control (except when stopped).
The external torque reference will be limited if torque control is selected (internal
32 No No No Yes Yes 6-129
torque reference < external torque reference).
Output when the motor is rotating at the speed limit.
6-87
33 Zero-servo end (ON: Zero-servo function completed) No No No Yes No
6-146

Frequency (FOUT) detection 5 (ON: Output frequency ≥ + L4-01 or output

36 Yes Yes Yes Yes Yes 6-50
frequency ≤ L4-01, L4-02 used, OFF: during baseblock

During run 2 (ON: Frequency output, OFF: Base block, DC injection braking, ini-
37 Yes Yes Yes Yes Yes 6-86
tial excitation, operation stop)

3D Inverter's Cooling Fan Fault detected Yes Yes Yes Yes Yes 6-73

„Analog Inputs: H3
User constants for analog inputs are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Signal level
selection (ter- 0: 0 to 10 V
minal A1) 1: -10V to 10 V
H3-01 0 or 1 0 No A A A A A 410H 6-28
[11-bit + polarity (posi-
端子 A1 信号 tive/negative) input]
选择

Gain (termi- Sets the frequency when 10 V

nal A1) 0.0 to
H3-02 is input, as a percentage of the 100.0% Yes A A A A A 411H 6-28
1000.0
端子 A1 增益 maximum output frequency.

Bias (termi- Sets the frequency when 0 V -100.0

H3-03 nal A1) is input, as a percentage of the to 0.0% Yes A A A A A 412H 6-28
端子 A1 偏置 maximum frequency. +100.0

Signal level
selection (ter- 0: 0 to 10 V
minal A3) 1: -10 V to 10 V 6-28
H3-04 0 or 1 0 No A A A A A 413H
[11-bit + polarity (posi- 6-128
端子 A3 信号 tive/negative) input]
电平

Multi-func-
tion analog
input (termi- Select multi-function analog 6-28
H3-05 nal A3) func- input function for terminal 0 to 1F 2 No A A A A A 414H
6-128
tion selection A3. Refer to the next page.

端子 A3 设定

Gain (termi- Sets the input gain (level)

nal A3) when 10 V is input. 0.0 to 6-28
H3-06 100.0% Yes A A A A A 415H
Set according to the 100% 1000.0 6-128
端子 A3 增益 value selected from H3-05.

5-50
 User Constant Tables

Name Control Methods

Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Bias (termi- Sets the input gain (level)
-100.0
nal A3) when 0 V is input. 6-28
H3-07 to 0.0% Yes A A A A A 416H
Set according to the 100% 6-128
端子 A3 偏置 +100.0
value selected from H3-05.

Signal level 0: 0 to 10V

selection 1: -10V to 10V
(terminal A2) 2: 4 to 20 mA (9-bit input). 6-28
H3-08 0 to 2 2 No A A A A A 417H
Switch current and voltage 6-128
端子 A2 信号 input using the switch on the
选择 control panel.

Multi-func-
tion analog
input (termi- Select multi-function analog 6-28
H3-09 nal A2) func- input function for terminal 0 to 1F 0 No A A A A A 418H
6-128
tion selection A2. Refer to the next table.

端子 A2 设定

Gain Sets the input gain (level)

(terminal A2) when 10 V (20 mA) is input.
0.0 to 6-29
H3-10 Set according to the 100% 100.0% Yes A A A A A 419H
1000.0 6-128
端子 A2 增益 value for the function set for
H3-09.

Bias Sets the input gain (level)

(terminal A2) when 0 V (4 mA) is input. -100.0
6-29
H3-11 Set according to the 100% to 0.0% Yes A A A A A 41AH
6-129
端子 A2 偏置 value for the function set for +100.0
H3-09.
Analog input Sets primary delay filter time
filter time constant in seconds for the
constant 0.00 to 0.03
H3-12 analog input terminal. No A A A A A 41BH 6-29
2.00 s
Effective for noise control
模拟量滤波
时间 etc.

5-51
 H3-05,H3-09 Settings
Control Methods
Set- Open Open
ting Function Contents (100%) V/f Loop Flux Loop Page
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
6-30
0 Add to terminal A1 Maximum output frequency Yes Yes Yes Yes Yes
6-129

Frequency reference (voltage) command

1 Frequency gain Yes Yes Yes Yes Yes 6-30
value

Auxiliary frequency reference 1

2 Maximum output frequency Yes Yes Yes Yes Yes 6-5
(2nd step analog)
Auxiliary frequency reference 2
3 Maximum output frequency Yes Yes Yes Yes Yes 6-5
(3rd step analog)

4 Voltage bias 200 V (200 V Class)/400 V (400 V Class) Yes Yes No No No -

Accel/decel change (reduction Set acceleration and deceleration times
5 Yes Yes Yes Yes Yes 6-18
coefficient) (C1-01 to C1-08)

6 DC injection braking current Inverter rated output current Yes Yes Yes No No 6-17
Overtorque/undertorque detection Motor rated torque for vector control
7 Yes Yes Yes Yes Yes 6-56
level Inverter rated output current for V/f control

8 Stall prevention level during run Inverter rated output current Yes Yes No No No 6-50
Frequency reference lower limit
9 Maximum output frequency Yes Yes Yes Yes Yes 6-35
level

A Jump frequency Maximum output frequency Yes Yes Yes Yes Yes 6-32
B PID feedback Maximum output frequency Yes Yes Yes Yes Yes 6-109

C PID target value Maximum output frequency Yes Yes Yes Yes Yes 6-109

D Frequency bias 2 Maximum output frequency Yes Yes Yes Yes Yes 6-31
E Motor temperature input 10 V = 100% Yes Yes Yes Yes Yes 6-61

10 Positive torque limit Motor's rated torque No No Yes Yes Yes 6-47

11 Negative torque limit Motor's rated torque No No Yes Yes Yes 6-47

12 Regenerative torque limit Motor's rated torque No No Yes Yes Yes 6-47

Torque reference/torque limit at

13 Motor’s rated torque No No No Yes Yes 6-129
speed control

14 Torque compensation Motor’s rated torque No No No Yes Yes 6-129

15 Positive/negative torque limit Motor's rated torque No No Yes Yes Yes 6-47

1F Analog input not used. - Yes Yes Yes Yes Yes 6-6

16 to 1E Not used - - - - - - -

5-52
 User Constant Tables

„Multi-function Analog Outputs: H4

User constants for multi-function analog outputs are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Monitor Sets the number of the monitor
selectionitem to be output (U1-††)
(terminalfrom terminal FM.
H4-01 1 to 45 2 No A A A A A 41DH 6-88
FM) 4, 10 to 14, 25, 28, 34, 39, 40
cannot be set. 29 to 31 and 41
端子 FM 设定 are not used.

Gain (ter-
Sets the multi-function analog
minal FM)output 1 voltage level gain.
Sets whether the monitor item
output will be output in multi- 0.00 to 4-6
H4-02 ples of 10 V. 1.00 Yes Q Q Q Q Q 41EH
2.50 6-88
端子 FM 增益 The maximum output from the
terminal is 10 V. A meter cali-
bration function is available.*

Bias (termi- Sets the multi-function analog

nal FM) output 1 voltage level bias.
Sets output characteristic up/
down parallel movement as a -10.0 to
H4-03 percentage of 10 V. 0.0% Yes A A A A A 41FH 6-88
+10.0
端子 FM 偏置 The maximum output from the
terminal is 10 V. A meter cali-
bration function is available.*

Monitor Sets the number of the monitor

selectionitem to be output (U1-††)
(terminalfrom terminal AM.
H4-04 1 to 45 3 No A A A A A 420H 6-88
AM) 4, 10 to 14, 25, 28, 34, 39, 40
cannot be set. 29 to 31 and 41
端子 AM 设定 are not used.

Gain (ter-
Set the voltage level gain for
minal AM)multi-function analog output 2.
Set the number of multiples of
10 V to be output as the 100% 0.00 to 4-6
H4-05 output for the monitor items. 0.50 Yes Q Q Q Q Q 421H
2.50 6-88
端子 AM 增益 The maximum output from the
terminal is 10 V. A meter cali-
bration function is available.*

Bias (termi- Sets the multi-function analog

nal AM) output 2 voltage level bias.
Sets output characteristic up/
down parallel movement as a -10.0 to
H4-06 percentage of 10 V. 0.0% Yes A A A A A 422H 6-88
+10.0
端子 AM 偏置 The maximum output from the
terminal is 10 V. A meter cali-
bration function is available.*
Analog out-
put 1 signal Sets the signal output level for
level selec- multi-function output 1 (termi-
H4-07 tion nal FM) 0 or 1 0 No A A A A A 423H 6-88
0: -10 to 10 V output
AO1 信号电 1: -10 to 10 V output
平

5-53
 Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Analog out-
put 2 signal Sets the signal output level for
level selec- multi-function output 2 (termi-
H4-08 tion nal AM) 0 or 1 0 No A A A A A 424H -
0: 0 to +10 V output
AO2 信号电 1: 0 to ±10 V output
平

* The CH1 output can be adjusted when the H4-02 or H4-03 setting is displayed in Quick, Advanced, or Verify mode while the motor is stopped.
The CH2 output can be adjusted when the H4-05 or H4-06 setting is displayed in Quick, Advanced, or Verify mode while the motor is stopped.
For analog output, the value equivalent to 100% of output value of monitored item is multiplied by the gain setting and the set bias is added.

„MEMOBUS Communications: H5
User constants for MEMOBUS communications are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Slave
address 0 to 20
H5-01 Set the Inverter's slave address. 1F No A A A A A 425H 6-94
*
从站地址

Communi- Set the baud rate for MEMO-

cation BUS communications of com-
speed selec- munications connection
tion terminals.
H5-02 0: 1200 bps 0 to 4 3 No A A A A A 426H 6-94
1: 2400 bps
通信速度选 2: 4800 bps
择 3: 9600 bps
4: 19200 bps

Communi- Set the parity for MEMOBUS

cation par- communications of communi-
ity selection cations connection terminals.
H5-03 0 to 2 0 No A A A A A 427H 6-94
0: No parity
通信校验选 1: Even parity
择 2: Odd parity

Stopping Set the stopping method for

method communications errors.
after com- 0: Deceleration to stop using
munication deceleration time in C1-02
H5-04 0 to 3 3 No A A A A A 428H 6-94
error 1: Coast to stop
2: Emergency stop using
通信错误检 deceleration time in C1-09
出错误 3: Continue operation

Communi- Set whether or not a communi-

cation error cations timeout is to be
detection detected as a communications
H5-05 selection 0 or 1 1 No A A A A A 429H 6-94
error.
通信错误检
0: Do not detect.
出选择 1: Detect

Send wait
time Set the time from the Inverter
H5-06 receiving data to when the 5 to 65 5 ms No A A A A A 42AH 6-94
通信等待时 Inverter starts to send.
间

5-54
 User Constant Tables

Name Control Methods

Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
RTS con- Select to enable or disable
trol ON/ RTS control.
OFF 0: Disabled (RTS is always
H5-07 0 or 1 1 No A A A A A 42BH 6-94
ON)
RTS 控制选 1: Enabled (RTS turns ON
择 only when sending)
Unit Selec- Selects the units used for
tion for MEMOBUS registry 0025H
MEMO- (monitors the output voltage
H5-10 BUS Regis- 0 or 1 0 No A A A A A 436H 6-95
reference).
ter 0025H 0: 0.1 V units
MEM25H 单位 1: 1 V units

* Set H5-01 to 0 to disable Inverter responses to MEMOBUS communications.

5-55
 „Pulse Train I/O: H6
User constants for pulse I/O are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Pulse train
input func-
tion selec- 0: Frequency reference 6-2
H6-01 tion 1: PID feedback value 0 to 2 0 No A A A A A 42CH 6-33
2: PID target value 6-108
脉冲输入选
择

Pulse train
input scal- Set the number of pulses in
ing 1000 to 1440 6-2
H6-02 hertz, taking the reference to be Yes A A A A A 42DH
32000 Hz 6-33
脉冲输入比
100%.
例

Pulse train
input gain Set the input gain level as a per-
0.0 to
H6-03 cent when the pulse train set in 100.0% Yes A A A A A 42EH 6-33
脉冲输入增
1000.0
H6-02 is input.
益

Pulse train
input bias -100.0
Set the input bias when the
H6-04 to 0.0% Yes A A A A A 42FH 6-33
脉冲输入偏
pulse train is 0.
100.0
置

Pulse train
input filter Set the pulse train input pri-
time 0.00 to 0.10
H6-05 mary delay filter time constant Yes A A A A A 430H 6-33
2.00 s
脉冲输入滤
in seconds.
波时间

Pulse train Select the pulse train monitor

monitor output items (value of the ††
1, 2, 5,
selection part of U1-††).
H6-06 20, 24, 2 Yes A A A A A 431H 6-90
There are two types of monitor
脉冲监视选
36
items: Speed-related items and
择 PID-related items.

Pulse train Set the number of pulses output

monitor when speed is 100% in hertz.
scaling Set H6-06 to 2, and H6-07 to 0, 0 to 1440
H6-07 Yes A A A A A 432H 6-90
to make the pulse train monitor 32000 Hz
脉冲监视比 output synchronously to the
例 output frequency.

5-56
 User Constant Tables

‹ L: Protection Function Constants

The following settings are made with the protection function constants (L constants): Motor selection func-
tion, power loss ridethrough function, stall prevention function, frequency detection, torque limits, and hard-
ware protection.

„Motor Overload: L1
User constants for motor overloads are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Motor pro- Sets whether the motor over-
tection load function is enabled or dis-
selection abled at electric thermal
overload relay.
0: Disabled
1: General-purpose motor
protection
2: Inverter motor protection
3: Vector motor protection
In some applications when the 4-5
L1-01 0 to 3 1 No Q Q Q Q Q 480H
Inverter power supply is 6-57
电机保护功 turned off, the thermal value is
能选择 reset, so even if this constant is
set to 1, protection may not be
effective.
When several motors are con-
nected to one Inverter, set to 0
and ensure that each motor is
installed with a protection
device.

Motor pro- Sets the electric thermal detec-

tection time tion time in seconds units.
constant Usually setting is not necessary.
The factory setting is 150%
overload for one minute. 0.1 to
L1-02 1.0 min No A A A A A 481H 6-57
When the motor's overload 5.0
电机保护时 resistance is known, also set the
间 overload resistance protection
time for when the motor is hot
started.

Alarm oper- Set H3-09 to E and select the

ation selec- operation when the input motor
tion during temperature (thermistor) input
motor over- exceeds the alarm detection
heating level (1.17 V).
0: Decelerate to stop using the
L1-03 0 to 3 3 No A A A A A 482H 6-60
deceleration time in C1-02.
1: Coast to stop
OH3 2: Emergency stop using the
检出动作 deceleration time in C1-09.
3: Continue operation (H3 on
the Operator flashes).

5-57
 Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Motor over- Set H3-09 to E and select the
heating operation when the motor tem-
operation perature (thermistor) input
selection exceeds the operation detec-
tion level (2.34 V).
L1-04 0 to 2 1 No A A A A A 483H 6-60
0: Decelerate to stop using the
OH4 检出动
deceleration time in C1-02.
作 1: Coast to stop
2: Emergency stop using the
deceleration time in C1-09.

Motor tem-
perature
input filter Set H3-09 to E and set the pri-
time con- mary delay time constant for 0.00 to
L1-05 0.20 s No A A A A A 484H 6-60
stant motor temperature (thermistor) 10.00
inputs in seconds.
OH4 检出动
作

„Power Loss Ridethrough: L2

User constants for power loss ridethroughs are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Momentary 0: Disabled [main circuit
power loss undervoltage (UV1)
detection detection]
1: Enabled [Restarted when
the power returns within the
time for L2-02. When L2-
02 is exceeded, main circuit
L2-01 undervoltage (UV1) is 0 to 2 0 No A A A A A 485H 6-63
瞬时停电动
detected.]
作选择 2: Enabled while CPU is
operating. [Restarts when
power returns during
control operations. Does not
detect main circuit
undervoltage (UV1).]
Momentary
power loss Ridethrough time, when
ridethru Momentary Power Loss Selec- 0 to 0.1 s
L2-02 time No A A A A A 486H 6-63
tion (L2-01) is set to 1, in units 25.5 *1

瞬时停电补
of seconds.
偿时间

5-58
 User Constant Tables

Name Control Methods

Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Min. base-
Sets the Inverter's minimum
block time
baseblock time in units of one
second, when the Inverter is
restarted after power loss ride-
through.
Sets the time to approximately 0.1 to 0.2 s 6-63
L2-03 No A A A A A 487H
0.7 times the motor secondary 5.0 *1 6-66
最小 BB 时间 circuit time constant.
When an overcurrent or over-
voltage occurs when starting a
speed search or DC injection
braking, increase the set values.
Voltage Sets the time required to return
recovery the Inverter output voltage to
time normal voltage at the comple-
tion of a speed search, in units 0.0 to 0.3 s 6-63
L2-04 No A A A A A 488H
of one second. 5.0 *1 6-66
电压恢复时 Sets the time required to
间 recover from 0 V to the maxi-
mum voltage.

Undervolt- Sets the main circuit undervolt-

age detec- age (UV) detection level (main
tion level circuit DC voltage) in V units.
150 to
Usually setting is not necessary. 190 V
L2-05 210 No A A A A A 489H 6-64
Insert an AC reactor in the *2
*2
PUV 检出值 Inverter input side to lower the
main circuit undervoltage
detection level.

KEB decel- Sets in seconds the time

eration time required to decelerate from the
speed where the deceleration at 0.0 to
L2-06 0.0 s No A A A A A 48AH -
KEB 减速时
momentary power loss com- 200.0
间 mand (KEB) is input to zero-
speed.

Momentary
recovery Set in seconds the time to
time accelerate to the set speed after 0.0 to 0.0 s
L2-07 No A A A A A 48BH -
recovery from a momentary 25.5 *3
瞬时停电恢 power loss.
复时间

Frequency Sets as a percent the about to

reduction reduce the output frequency at
gain at KEB the beginning of deceleration at
0 to
L2-08 start momentary power loss (KEB). 100 No A A A A A 48CH -
300
Reduction = slip frequency
KEB 频率增 before KEB operation × L2-08
益 ×2
Note Attach a Backup Capacitor Unit for Momentary Power Loss if compensation for power interruptions of up to 2.0 seconds is required for 200 V/400 V
Class Inverters with outputs of 0.4 to 7.5 kW.
* 1. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given.
* 2. These are values for a 200 V Class Inverter. Value for a 400 V Class Inverter is double.
* 3. If the setting is 0, the axis will accelerate to the specified speed for the specified acceleration time (C1-01 to C1-08).

5-59
 „Stall Prevention: L3
User constants for the stall prevention function are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Stall pre- 0: Disabled (Acceleration as
vention set. With a heavy load, the
selection motor may stall.)
during accel 1: Enabled (Acceleration
stopped when L3-02 level is
exceeded. Acceleration
starts again when the 4-21
L3-01 0 to 2 1 No A A A No No 48FH
current is returned.) 6-23
加速防止失
2: Intelligent acceleration
速选择 mode (Using the L3-02
level as a basis, acceleration
is automatically adjusted.
Set acceleration time is
disregarded.)

Stall pre- Effective when L3-01 is set to 1

vention or 2.
level dur- Set as a percentage of Inverter
ing accel rated current. 0 to 4-21
L3-02 150% No A A A No No 490H
Usually setting is not necessary. 200 6-23
The factory setting reduces the
加速防止
失速值 set values when the motor
stalls.
Stall pre- Sets the lower limit for stall
vention prevention during acceleration,
limit dur- as a percentage of the Inverter
0 to 4-21
L3-03 ing accel rated current, when operation is 50% No A A A No No 491H
100 6-23
in the frequency range above
加速防止失 E1-06.
速极限 Usually setting is not necessary.

Stall pre- 0: Disabled (Deceleration as

vention set. If deceleration time is
selection too short, a main circuit
during overvoltage may result.)
decel 1: Enabled (Deceleration is
stopped when the main
circuit voltage exceeds the
overvoltage level.
Deceleration restarts when
voltage is returned.)
2: Intelligent deceleration
4-6
mode (Deceleration rate is 0 to 3
L3-04 1 No Q Q Q Q Q 492H 4-21
automatically adjusted so *1
6-25
that the Inverter can
减速防止失 decelerate in the shortest
速选择 possible time. Set
deceleration time is
disregarded.)
3: Enabled (with Braking
Resistor Unit)
When a braking option (Brak-
ing Resistor, Braking Resistor
Unit, Braking Unit) is used,
always set to 0 or 3.

5-60
 User Constant Tables

Name Control Methods

Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Stall pre- 0: Disabled (Runs as set. With
vention a heavy load, the motor may
selection stall.)
during run- 1: Deceleration time 1 (the
ning deceleration time for the
4-21
L3-05 stall prevention function is 0 to 2 1 No A A No No No 493H
6-49
C1-02.)
运行中防失
2: Deceleration time 2 (the
速选择 deceleration time for the
stall prevention function is
C1-04.)

Stall pre- Effective when L3-05 is 1 or 2.

vention Set as a percentage of the
level dur- Inverter rated current.
30 to 4-21
L3-06 ing running Usually setting is not necessary. 160% No A A No No No 494H
200 6-49
The factory setting reduces the
运行中防止 set values when the motor
失速值 stalls.
Overvolt- 0: Disabled
age inhibit 1: Enabled
selection Used to enable or disable the
function for inhibiting main cir-
cuit overvoltages by reducing
the regenerative torque limit 4-21
L3-11 according to the main circuit 0 or 1 0 No No No A A A 4C7H 6-27
overvoltage level. 7-3
OV 抑制功能
选择 If this function is enabled,
when the main circuit voltage
rises, operation will be per-
formed with the regenerative
torque less than the set value.

Overvolt- Sets the main circuit voltage

age inhibit level for which the regenerative
voltage torque limit is restricted to 0.
level Usually, there is no need to 350 to
380V 4-21
L3-12 change this setting. If main cir- 390 No No No A A A 4C8H
*2 6-27
cuit overvoltages occur even *2
OV 抑制电压 with the overvoltage inhibit
值 function enabled, reduce this
setting.
* 1. The setting range for flux vector and open-loop vector 2 controls is 0 to 2.
* 2. These values are for a 200 V Class Inverter. For a 400 V Class Inverter, double the values.

„Reference Detection: L4
User constants for the reference detection function are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Speed agree Effective when “Desired fre-
detection quency (ref/setting) agree 1,”
level “Frequency detection 1,” or
0.0 to
L4-01 “Frequency detection 2" is set 0.0 Hz No A A A A A 499H 6-50
400.0
for a multi-function output.
频率检出值 Frequencies to be detected are
set in Hz units.

5-61
 Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Speed agree Effective when “Frequency
detection (speed) agree 1,” “Desired fre-
width quency (speed) agree 1,” or
“Frequency (FOUT) detection
0.0 to
L4-02 1,” Frequency (FOUT) detec- 2.0 Hz No A A A A A 49AH 6-50
20.0
tion 2 is set for a multi-function
频率检出幅
度 output.
Sets the frequency detection
width in Hz units.
Speed agree Effective when “Desired fre-
detection quency (speed) agree 2,” “Fre-
level (+/-) quency (FOUT) detection 3,”
-400.0
or “Frequency (FOUT) detec-
L4-03 to 0.0 Hz No A A A A A 49BH 6-51
tion 4" is set for a multi-func-
+400.0
频率检出值 tion output.
＋－ Frequency that should be
detected is set in Hz units.

Speed agree Effective when “Frequency

detection (speed) agree 2,” “Desired fre-
width (+/-) quency (speed) agree 2,” Fre-
quency (FOUT) detection 3 or 0.0 to
L4-04 2.0 Hz No A A A A A 49CH 6-51
“Frequency detection 4" is set 20.0
频率检出幅
度
for a multi-function output.
＋－ Frequency detection width is
set in Hz units.

Operation 0: Stop (Operation follows the

when fre- frequency reference.)
quency ref- 1: Operation at 80% speed
erence is continues. (At 80% of speed
L4-05 missing before the frequency 0 or 1 0 No A A A A A 49DH 6-71
reference was lost)
Frequency reference is lost:
指令丧失动
作选择 Frequency reference dropped
over 90% in 400 ms.

„Fault Restart: L5
User constants for restarting faults are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Number of Sets the number of auto restart
auto restart attempts.
L5-01 attempts Automatically restarts after a 0 to 10 0 No A A A A A 49EH 6-72
故障重试次
fault and conducts a speed
数 search from the run frequency.

Auto restart Sets whether a fault contact

operation output is activated during fault
selection restart.
L5-02 0: Not output (Fault contact is 0 or 1 0 No A A A A A 49FH 6-72
故障重试接
not activated.)
点动作 1: Output (Fault contact is
activated.)

5-62
 User Constant Tables

„Torque Detection: L6
User constants for the torque detection function are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Overtorque/ 0: Overtorque/undertorque
Under- detection disabled.
torque 1: Overtorque detection only
detection with speed agreement;
selection 1 operation continues after
overtorque (warning).
2: Overtorque detected
continuously during
operation; operation
continues after overtorque
(warning).
3: Overtorque detection only
with speed agreement;
output stopped upon
detection (protected
operation).
4: Overtorque detected
continuously during
operation; output stopped
upon detection (protected
L6-01 0 to 8 0 No A A A A A 4A1H 6-53
operation).
5: Undertorque detection only
转矩检出 1 with speed agreement;
动作 operation continues after
overtorque (warning).
6: Undertorque detected
continuously during
operation; operation
continues after overtorque
(warning).
7: Undertorque detection only
with speed agreement;
output stopped upon
detection (protected
operation).
8: Undertorque detected
continuously during
operation; output stopped
upon detection (protected
operation).
Overtorque/
Under- Open-loop vector control:
torque Motor rated torque is set as
detection 0 to
L6-02 100%. 150% No A A A A A 4A2H 6-53
level 1 300
V/f control: Inverter rated cur-
转矩检出 1
rent is set as 100%.
值

Overtorque/
Under-
torque Sets the overtorque/under-
detection 0.0 to
L6-03 torque detection time in 1-sec- 0.1 s No A A A A A 4A3H 6-54
time 1 10.0
ond units.
转矩检出 1
时间

5-63
 Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Overtorque/
Under-
torque
L6-04 detection 0 to 8 0 No A A A A A 4A4H 6-54
selection 2

转矩检出 2
动作 Multi-function output for over-
torque detection 1 is output to
Overtorque/ multi-function contact output
Under- when overtorque detection 1
torque NO or overtorque detection 1
detection 0 to
L6-05 NC is selected. Multi-function 150% No A A A A A 4A5H 6-54
level 2 300
output for overtorque detection
2 is output to multi-function
转矩检出 2
值 contact output when overtorque
detection 2 NO or overtorque
Overtorque/ detection 2 NC is selected.
Under-
torque
detection 0.0 to
L6-06 0.1 s No A A A A A 4A6H 6-54
time 2 10.0

转矩检出 2
时间

„Torque Limits: L7
User constants for torque limits are shown in the following table.
Control Methods
Con- Change Open Open MEMO-
Fac-
stant Setting during BUS
Num-
Name Description Range
tory
Opera-
V/f Loop Flux Loop Page
Setting V/f with Vec- Vec- Vec- Regis-
ber tion PG tor tor tor ter
1 2

Forward
drive
torque 0 to 4-21
L7-01 limit 200% No No No A A A 4A7H
300 6-46
正转电动转
矩极限

Reverse
Sets the torque limit value as a per-
drive
centage of the motor rated torque.
torque 0 to 4-21
L7-02 limit Four individual regions can be set. 200% No No No A A A 4A8H
300 6-46
反转电动转 Output torque
矩极限 Positive torque

Forward No. of
Regenerative motor
regenera- Reverse state rotations
tive torque Regenerative Forward 0 to 4-21
L7-03 limit state 200% No No No A A A 4A9H
300 6-46
Negative torque
正转再生转
矩极限

Reverse
regenera-
tive torque 0 to 4AA 4-21
L7-04 limit 200% No No No A A A
300 H 6-46
反转再生转
矩极限

5-64
 User Constant Tables

Control Methods
Con- Change Open Open MEMO-
Fac-
stant Setting during BUS
Num-
Name Description Range
tory
Opera-
V/f Loop Flux Loop Page
Setting V/f with Vec- Vec- Vec- Regis-
ber tion PG tor tor tor ter
1 2

Integral
time set-Set the integral time for the torque
ting for limit. When integral control is set for
5 to 200 4-21
L7-06 torque the torque limit, reduce this setting to No No No A No No 4ACH
limit 10,000 ms 6-46
increase the change in frequency for
转矩限制时
the torque limit.
间

Control
method
selection Select the control method for the
for torque torque limit during acceleration and
limit dur- deceleration.
0: Proportional control (integral con- 4-21
L7-07 ing accel- 0, 1 0 No No No A No No 4C9H
eration and trol during constant speed) 6-46
decelera- 1: Integral control
tion Normally, this constant does not need
to be set.
转矩极限控
制选择

„Hardware Protection: L8
User constants for hardware protection functions are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Protect selec-
tion for inter- 0: Disabled (no overheating
nal DB protection)
L8-01 resistor (Type 0 or 1 0 No A A A A A 4ADH 6-74
1: Enabled (overheating
ERF) protection)
制动电阻保护

Overheat pre- Sets the detection temperature

alarm level for the Inverter overheat
detection pre-alarm in °C. 50 to
L8-02
The pre-alarm detects when 130 95 °C*1 No A A A A A 4AEH 6-75
过热预警检出
值 the heatsink temperature
reaches the set value.
Operation Sets the operation for when
selection after the Inverter overheat pre-
overheat pre- alarm goes ON.
alarm 0: Ramp to stop
(Deceleration stop using
Deceleration Time 1, C1-
02.)
1: Coast to stop
L8-03 0 to 3 3 No A A A A A 4AFH 6-75
2: Fast stop (Emergency stop
using the deceleration
过热预警动作
选择 time in C1-09.)
3: Continue operation
(Monitor display only.)
A fault will be given in set-
ting 0 to 2 and a minor fault
will be given in setting 3.

5-65
 Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Input open- 0: Disabled
phase protec- 1: Enabled (Detects if input
tion selection current open-phase, power
supply voltage imbalance
or main circuit
L8-05 electrostatic capacitor 0 or 1 0 No A A A A A 4B1H -
deterioration occurs.)
输入缺相保护 This fault is detected if a load
is greater than approximately
80% of the maximum motor
capacity.

Output open- 0: Disabled

phase protec- 1: Enabled
tion selection 2: Enabled
Output open-phase is detected
at less than 5% of Inverter
rated current.
L8-07 0 to 2 0 No A A A A A 4B3H -
When applied motor capacity
输入缺相保护 is small for Inverter capacity,
值 output open-phase may be
detected inadvertently or
open-phase may not be
detected. In this case, set to 0.

Ground pro-
tection selec-
tion 0: Disabled
L8-09 0 or 1 1 No A A A A A 4B5H -
1: Enabled
接地短路保护
选择

Cooling fan Set the ON/OFF control for

control selec- the cooling fan.
tion 0: ON only when Inverter is
L8-10 0 or 1 0 No A A A A A 4B6H -
ON
风扇控制选择 1: ON whenever power is
ON

Cooling fan
control delay Set the time in seconds to
time delay turning OFF the cooling 0 to
L8-11 60 s No A A A A A 4B7H -
fan after the cooling fan OFF 300
风扇控制延迟 command is received.
时间

Ambient tem- Set the ambient temperature.

perature If set to 60 °C, the Inverter 45 to
L8-12 45 °C No A A A A A 4B8H -
overload protection function 60
环境温度 (OL2) will start 20% earlier.
OL2 charac-
teristics 0: OL2 characteristics at low
selection at speeds disabled.
L8-15 0 or 1 1 No A A A A A 4BBH -
low speeds 1: OL2 characteristics at
low speeds enabled.
低速 OL2 特性

Soft Current
Limitation 0: Disable (gain = 0)
L8-18 0 or 1 1 No A A A A A 4BEH -
1: Enable
软件 CLA

OH1 detec-
tion of 0: Disabled (FAN minor
Inverter’ s fault detection)
L8-32 0 or 1 1 No A A A A A 4E2H 6-73
cooling fan 1: Enabled (OH1 major fault
detection)
OH1 检出选择

5-66
 User Constant Tables

Name Control Methods

Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Carrier
frequency 0: Disabled (No carrier
reduction frequency reduction.)
1
L8-38 selection 1: Enabled (Carrier 0 or 1 No A A A No No 4EFH -
*2
frequency is reduced
载波频率降低 accordingly.)
选择

Reduced
carrier 0, 4 to 2.0 kHz
Sets the reduced carrier fre-
L8-39 frequency 2.0 *1 *2 No A A A No No 4F0H -
quency.
*3
降低载波频率

Current alarm Allows or restricts an alarm

from being triggered when
the relative output current
L8-41 rises above 150%. 0 or 1 1 No A A A A A 4F2H 6-181
电流警告 0: Disabled.
1: Enabled (alarm will be
output).
* 1. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given.
* 2. If a current exceeding 110% of the Inverter rated current flows through the unit, the carrier frequency will automatically decrease and electromagnetic
noise will occur.
* 3. The lower limits are 0.4 kHz for V/f control and 1.0 kHz for flux vector control. The upper limit is the same value as that of the factory setting for L8-
39.

5-67
 ‹ N: Special Adjustments
The following settings are made with the special adjustments constants (N constants): Hunting prevention,
speed feedback detection control, high-slip braking, speed estimation, and feed forward control.

„Hunting Prevention Function: N1

User constants for hunting prevention are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Hunting-pre- 0: Hunting-prevention
vention func- function disabled
tion selection 1: Hunting-prevention
function enabled
The hunting-prevention func-
tion suppresses hunting when
the motor is operating with a
N1-01 0 or 1 1 No A A No No No 580H 6-40
light load.
防止失调功能 This function is enabled in V/
选择 f control method only.
If high response is to be given
priority over vibration sup-
pression, disable the hunting-
prevention function.

Hunting-pre- Set the hunting-prevention

vention gain gain multiplication factor.
Normally, there is no need to
make this setting.
Make the adjustments as fol-
lows:
• If vibration occurs with 0.00 to 4-18
N1-02 1.00 No A A No No No 581H
light load, increase the set- 2.50 6-40
防止失调增益 ting.
• If the motor stalls, reduce
the setting.
If the setting is too large, the
voltage will be too suppressed
and the motor may stall.

Hunting-pre-
vention time Set the hunting-prevention
0 to
N1-03 constant primary delay time in units of
500 10 ms * No A A No No No 582H 6-40
ms.
防止失调时间

* The factory setting depends upon the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given.

5-68
 User Constant Tables

„Speed Feedback Protection Control Functions: N2

User constants for speed feedback protection control functions are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Speed feed- Set the internal speed feed-
back detec- back detection control gain
tion control using the multiplication func-
(AFR) gain tion.
Normally, there is no need to
make this setting.
Adjust this constant as fol-
0.00 to 4-18
N2-01 lows: 1.00 No No No A No No 584H
10.00 6-41
• If hunting occurs, increase
AFR 增益 the set value.
• If response is low, decrease
the set value.
Adjust the setting by 0.05 at a
time, while checking the
response.

Speed feed-
back detec- Set the time constant to
tion control decide the rate of change in 0 to
N2-02 (AFR) time 50 ms No No No A No No 585H 6-41
the speed feedback detection 2000
constant control.
AFR 时间

Speed feed-
back detec- Increase the setting if over-
tion control voltage (OV) failures occur at
0 to
N2-03 (AFR) time the completion of accelera- 750 ms No No No A No No 586H 6-41
2000
constant 2 tion or when the load changes
radically.
AFR 时间 2

„High-slip Braking: N3
User constants for high-slip braking are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
High-slip
braking Sets the frequency width for
deceleration deceleration during high-slip
N3-01 frequency braking as a percent, taking 1 to 20 5% No A A No No No 588H -
width the Maximum Frequency
(E1-04) as 100%.
HSB 频率幅度

High-slip Sets the current limit for

braking cur- deceleration during high-slip
rent limit braking as a percent, taking
100 to
N3-02 the motor rated current as 150% No A A No No No 589H -
200
100%. The resulting limit
HSB 电流限制 must be 150% of the Inverter
rated current or less.

5-69
 Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
High-slip Set in seconds the dwell time
braking stop for the output frequency for
dwell time FMIN (1.5 Hz) during V/f 0.0 to
N3-03 1.0 s No A A No No No 58AH -
control. 10.0
HSB 暂停时间 Effective only during deceler-
ation for high-slip braking.
High-slip Set the OL time when the out-
braking OLput frequency does not
30 to
N3-04 time change for some reason dur- 40 s No A A No No No 58BH -
1200
ing deceleration for high-slip
HSOL 检出时间 braking.

„Speed Estimation: N4
User constants for speed estimation are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Integral time
of speed esti- Set the integral time of the 0.000
mator 0.030
N4-07 speed estimator for PI con- to No No No No No A 59AH 4-20
ms
trol. 9.999
速度推定积分
时间

Proportional
gain of speed Set the proportional gain of
estimator 0 to
N4-08 the speed estimator for PI 15 No No No No No A 59BH -
1000
control.
速度推定比例
增益

High-speed
proportional
gain of speed Set the high-speed propor-
0 to
N4-10 estimator tional gain of the speed esti- 15.0 No No No No No A 59DH 4-20
1000.0
mator for PI control.
推定高速积分
时间

Speed estima-
tor switching Set the switching frequency
frequency of high-speed/low-speed 40 to 7-33
N4-11 70 Hz No No No No No A 59EH
operation for the speed esti- 70 10-4
速度推定切换 mator.
频率

Low-speed Increase this setting if a

regeneration higher power for low-speed
stability coef- regeneration is required. If
0.0 to
N4-15 ficient 1 the setting is too large, the 0.3 No No No No No A 5A2H 7-33
3.0
torque reference monitor and
低速再生系数 the actual torque accuracy
1 may deteriorate.

Torque
adjustment Set the torque adjustment 0.0 to
N4-17 gain 0.8 No No No No No A 5A4H 7-33
gain for low-speed power. 5.0
转矩调整增益

5-70
 User Constant Tables

Name Control Methods

Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Feeder resis-
tance adjust- Set the gain for the feeder
ment gain 0.90 to
N4-18 resistance in the speed esti- 1.00 No No No No No A 5A5H -
1.30
mator.
反馈电阻调整
增益

Speed estima- Set the switching frequency

tor switching of high-speed/low-speed 20 to 7-33
N4-28 frequency 2 50 Hz No No No No No A 5AFH
operation for the speed esti- 70 10-4
SpeedF2 mator during deceleration.

Torque Gradually increase this set-

adjustment ting to improve low-speed
gain 2 power. If the setting is too
0.00 to
N4-29 high, the power may be 0.10 No No No No No A 5B4H 7-33
0.40
reduced.
Spd gain Usually, there is no need to
change this setting.
Low-speed Increase this setting to ensure
regeneration stable operation for extremely
stability coef- low-speed regeneration. If the
ficient 2 setting is set to a high value,
0.00 to
N4-30 the speed will increase with 1.00 No No No No No A 5B5H 7-32
10.00
the size of the regenerative
Coef 2 load.
Adjust this setting in intervals
of approximately 0.2.

Speed estima- Set the lower limit for the

tor gain fluc- fluctuation frequency of the
tuation 0.0 to
N4-32 speed estimator’s low-speed 5.0 Hz No No No No No A 5B7H 7-32
frequency 1 60.0
proportional gain (PI control).
Frq1 Set the value in Hz.

Speed estima- Set the upper limit for the

tor gain fluc- fluctuation frequency of the
tuation 0.0 to
N4-33 speed estimator’s low-speed 20.0 Hz No No No No No A 5B8H 7-32
frequency 2 60.0
proportional gain (PI control).
Frq2 Set the value in Hz.

Speed estima-
tor gain fluc- Set ratio for fluctuating the
tuation rate speed estimator’s low-speed 0.0 to
N4-34 200.0% No No No No No A 5B9H 7-32
proportional gain (PI control). 200.0
速度推定增益 Set the value as a percentage.
变化

„Feed Forward: N5
User constants for the feed forward control are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Feed forward Select the feed forward con-
control selec- trol. 0 4-21
N5-01 tion 0 or 1 No No No No A A 5B0H
0: Disabled *1 6-142
FF 控制选择 1: Enabled

5-71
 Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Motor accel- Set the time required to
eration time accelerate the motor at the
rated torque (T100) to the
rated speed (Nr).
J: GD2/4, P: Motor rated out- 0.001
put 0.178 s 4-21
N5-02 to No No No No A A 5B1H
*2 6-142
电机加速时间 ta =
2π x J [kgm2] x Nr [min-1]
[s]
10.000
60 x T100 [N x m]

However,
60 P [kW]
T100 = x × 103 [N x m]
2π Nr [min-1]

Feed forward Set the proportional gain for

proportional feed forward control.
gain 0.00 to 4-21
N5-03 Speed reference response will 1.0 No No No No A A 5B2H
100.00 6-142
前馈控制 P 增
increase as the setting of N5-
益 03 is increased.

* 1. When the control method is changed, the factory setting will change. The flux vector factory setting is given.
* 2. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given.

‹ o: Digital Operator Constants

The following settings are made with the Digital Operator constants (o constants): Multi-function selections
and the copy function.

„Monitor Select: o1
User constants for Digital Operator Displays are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Monitor Set the number of the monitor
selection item to be displayed in the
earliest 4 monitor items. (U1-
o1-01 ††) 4 to 99 6 Yes A A A A A 500H -
The output monitor voltage
显示项目选择 (factory setting) can be
changed.

Monitor Sets the monitor item to be

selection after displayed when the power is
power up turned on.
1: Frequency reference
o1-02 1 to 4 1 Yes A A A A A 501H 6-148
2: Output frequency
通电监视项目 3: Output current
选择 4: The monitor item set for
o1-01

5-72
 User Constant Tables

Name Control Methods

Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Frequency Sets the units that will be set
units of refer- and displayed for the fre-
ence setting quency reference and fre-
and monitor quency monitor.
0: 0.01 Hz units
1: 0.01% units (Maximum
output frequency is
100%)
2 to 39:
min−1 units (Sets the motor
poles.)
40 to 39999:
User desired display 0 to 6-148
o1-03 0 No A A A A A 502H
Set the desired values for 39999 6-166
setting and display for the
频率指令单位 max. output frequency.

Set 4-digit number

excluding the decimal
point.
Set the number of digits
below the decimal point
to display.
Example: When the max. out-
put frequency value is 200.0,
set 12000
Setting unit
for frequency Set the setting unit for fre-
constants quency reference-related con-
o1-04 related to V/f stants. 0 or 1 0 No No No No A A 503H 6-148
characteris- 0: Hz
tics
1: min−1
参数设定单位

LCD bright- Set a smaller value to lighten

ness adjust- the LCD and a larger value
o1-05 ment 0 to 5 3 Yes No No No A A 504H -
to darken the LCD (stan-
LCD 亮度调整 dard: 3).

5-73
 „Multi-function Selections: o2
User constants for Digital Operator key functions are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
LOCAL/ Sets the Digital Operator
REMOTE Local/Remote Key
key enable/ 0: Disabled
o2-01 disable 1: Enabled (Switches 0 or 1 1 No A A A A A 505H 6-148
between the Digital
L/R 键功能
Operator and the constant
settings.)

STOP key Sets the Stop Key in the run

during con- mode.
trol circuit 0: Disabled (When the Run
terminal Command is issued from
o2-02 0 or 1 1 No A A A A A 506H 6-149
operation and external terminal, the
Stop Key is disabled.)
STOP 键
1: Enabled (Effective even
during run.)

User con- Clears or stores user initial

stant initial values.
value 0: Stores/not set
1: Begins storing (Records
the set constants as user
initial values.)
o2-03 2: All clear (Clears all 0 to 2 0 No A A A A A 507H 6-149
recorded user initial
用户参数保存 values)
When the set constants are
recorded as user initial val-
ues, 1110 will be set in A1-
03.

kVA selection
o2-04
变频器容量
Do not set. 0 to FF 0* No A A A A A 508H -
选择

Frequency When the frequency reference

reference set- is set on the Digital Operator
ting method frequency reference monitor,
selection sets whether the Enter Key is
necessary.
o2-05 0: Enter Key needed 0 or 1 0 No A A A A A 509H 6-149
1: Enter Key not needed
频率指令设定
When set to 1, the Inverter
accepts the frequency refer-
ence without Enter Key oper-
ation.

Operation Sets the operation when the

selection Digital Operator is discon-
when digital nected.
operator is 0: Disabled (Operation
disconnected continues even if the
Digital Operator is
o2-06 0 or 1 0 No A A A A A 50AH -
disconnected.)
1: Enabled (OPR is detected
操作器断线 at Digital Operator
动作 disconnection. Inverter
output is cut off, and fault
contact is operated.)

Cumulative
operation Sets the cumulative operation
time setting time in hour units. 0 to
o2-07 0 hr No A A A A A 50BH 6-149
Operation time is calculated 65535
累积运行时间 from the set values.
设定

5-74
 User Constant Tables

Name Control Methods

Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Cumulative 0: Cumulative time when the
operation Inverter power is on. (All
time selection time while the Inverter
power is on is
o2-08 accumulated.) 0 or 1 0 No A A A A A 50CH -
1: Cumulative Inverter run
累积运行时间
选择 time. (Only Inverter
output time is
accumulated.)

Fan opera- Set the initial value of the fan

tion time set- operation time using time
ting 0 to 6-149
o2-10 units. 0 hr No A A A A A 50EH
65535 6-184
风扇累积运行
The operation time accumu-
时间 lates from the set value.

Fault trace/ 0: Disabled (U2 and U3 con-

fault history stants are on hold.)
o2-12 clear function 0 or 1 0 No A A A A A 510H -
1: Enabled (Initializes U2
故障记录清除
and U3 constants.)

Output power 0: Holds output power moni-

monitor clear tor.
o2-14 selection 0 or 1 0 No A A A A A 512H 5-80
1: Initializes output power
KWH 监视复位
monitor. (Returns to 0.)

Capacitor Allows the user to set the

maintenance maintenance time for the
setting electrolytic capacitors (U1-
0 to
o2-18 61). The user can reset the 0% No A A A A A 51DH 6-184
150
accumulated operation time
电容维护设定 back to zero, or to some other
desired value.
* The factory setting depends upon the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given.

„ Copy Function: o3
User constants for the copy function are shown in the following table.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Copy func- 0: Normal operation
tion selection 1: READ (Inverter to
Operator)
o3-01 0 to 3 0 No A A A A A 515H 6-151
2: COPY (Operator to
拷贝功能选择 Inverter)
3: Verify (compare)
Read permit-
ted selection 0: Read prohibited
o3-02 0 or 1 0 No A A A A A 516H 6-151
1: Read permitted
读出许可选择

5-75
 ‹ T: Motor Autotuning
The following settings are made with the motor autotuning constants (T constants): Settings for autotuning.
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Page
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Motor 1/2 Set the location where the
selection autotuned motor constants are
T1-00 to be stored. 1 or 2 1 No Yes Yes Yes Yes Yes 700H 4-14
1: Motor 1
选择电机
2: Motor 2

Autotuning Set the autotuning mode.

mode selec- 0: Rotational autotuning
tion 1: Stationary autotuning 1
2: Stationary autotuning for 0 4-10
T1-01 line-to-line resistance 0 to 4 No Yes Yes Yes Yes Yes 701H
*1 *6 4-14
选择自学习 only
模式 3: Shipping adjustment*5
4: Stationary autotuning 2*7

Motor output
power Set the output power of the 0.00 to 0.40
T1-02 motor in kilowatts. 650.00 kW No Yes Yes Yes Yes Yes 702H 4-14
*3
电机额定功率

Motor rated
voltage Set the rated voltage of the 0.0 to 200.0 V
T1-03 No No No Yes Yes Yes 703H 4-14
motor in volts. 255.5*2 *2
电机额定电压

Motor rated
current Set the rated current of the 0.32 to 1.90 A
T1-04 No Yes Yes Yes Yes Yes 704H 4-14
motor in amps. 6.40 *4 *3
电机额定电流

Motor base
frequency Set the base frequency of the 0.0 to
T1-05 motor in hertz. 400.0 50.0 Hz No No No Yes Yes Yes 705H 4-14
电机基本频率

Number of
motor poles Set the number of motor 2 to 48
T1-06 poles. poles 4 poles No No No Yes Yes Yes 706H 4-14
电机极数

Motor base
speed Set the base speed of the 0 to 1450
T1-07 No No No Yes Yes Yes 707H 4-15
motor in min−1. 24000 min−1
电机额定速度

Number of Set the number of pulses per

PG pulses revolution for the PG being
T1-08 when turning used (pulse generator or 0 to 600 No No Yes No Yes No 708H 4-15
encoder) without any multi- 60000
PG 脉冲数 plication factor.

Motor no- Set the current value recorded

load current in the motor’s test results for
a motor without a load. 0.00 to 1.20A
T1-09 No No No Yes Yes Yes 709H 4-15
电机的空载
Displayed only when Station- 1.89 *7 *3
电流
ary autotuning 2 is selected
(T1-01 = 4).
* 1. Set T1-02 and T1-04 when 2 is set for T1-01. Only set value 2 is possible for V/f control or V/f control with PG.
* 2. These are values for a 200 V Class Inverter. Values for a 400 V Class Inverter are double.
* 3. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter for 0.4 kW is given.
* 4. The setting range is from 10% to 200% of the Inverter rated output current. The value for a 200 V Class Inverter for 0.4 kW is given.
* 5. Refer to Chapter 8 Procedure for Adjusting Constants after Replacement of Control Board (Page 8-3) for the details of setting 3 (Shipping adjustment).
* 6. When the control method is changed, the factory setting will change. The open-loop vector 1 control factory setting is given.
* 7. The setting range depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. The upper limit depends on the setting of
E2-01.

5-76
 User Constant Tables

‹ U: Monitor Constants
The following settings are made with the monitor constants (U constants): Setting constants for monitoring in
drive mode.

„ Status Monitor Constants: U1

The constants used for monitoring status are listed in the following table.

Name Control Methods

Con- Output Signal Level Open Open MEMO-
Min. V/f Loop Flux Loop BUS
stant Description During Multi-Function
Number Display Unit V/f with Vec- Vec- Vec- Regis-
Analog Output PG tor tor tor ter
1 2
Frequency
reference Monitors/sets the fre- 10 V: Max. frequency 0.01
U1-01 A A A A A 40H
quency reference value.* (-10 to 10 V possible) Hz
预先设定指令

Output fre-
quency Monitors the output fre- 10 V: Max. frequency 0.01
U1-02 A A A A A 41H
quency.* (-10 to 10 V possible) Hz
输出频率

Output cur- 10 V: Inverter rated output

rent Monitors the output cur- current 0.01
U1-03 A A A A A 42H
rent. (0 to +10 V, absolute value A
输出电流 output)
Control
method Checks the current control
U1-04 (Cannot be output.) - A A A A A 43H
method.
控制模式

Motor speed Monitors the detected 10 V: Max. frequency 0.01

U1-05 No A A A A 44H
电机速度 motor speed.* (-10 to 10 V possible) Hz

Output volt- Monitors the output volt-

age 10 V: 200 VAC (400 VAC)
U1-06 age reference value in the 0.1 V A A A A A 45H
(0 to +10 V output)
输出电压 Inverter.

DC bus volt-
age Monitors the main DC 10 V: 400 VDC (800 VDC)
U1-07 1V A A A A A 46H
主回路直流电
voltage in the Inverter. (0 to +10 V output)
压

Output 10 V: Inverter capacity

power Monitors the output power (max. applicable motor 0.1
U1-08 A A A A A 47H
(internally detected value). capacity) kW
输出功率 (-10 to 10 V possible)

Torque refer- Monitor in internal torque

ence 10 V: Motor rated torque
U1-09 reference value for vector 0.1% No No A A A 48H
(-10 to 10 V possible)
转矩指令 control.

* The unit is set in o1-03 (frequency units of reference setting and monitor).

5-77
 Name Control Methods
Con- Output Signal Level Open Open MEMO-
Min. V/f Loop Flux Loop BUS
stant Description During Multi-Function Unit
Number Display V/f with Vec- Vec- Vec- Regis-
Analog Output PG tor tor tor ter
1 2
Input termi- Shows input ON/OFF status.
nal status U1-10= 00000000
1: FWD command
(S1) is ON.
1: REV command
(S2) is ON.
1: Multi input 1
(S3) is ON.
1: Multi input 2
(S4) is ON.
1: Multi input 3
(S5) is ON.
1: Multi input 4
(S6) is ON.
1: Multi input 5
(S7) is ON.
1:Multi input 6
U1-10 (S8) is ON. (Cannot be output.) - A A A A A 49H
输入端子状
The ON/OFF status of the fol-
态
lowing input terminals can be
checked by displaying U1-10
and pressing the Enter Key.
(Press the Enter Key again to
return to the original dis-
play.)
U1-10= 0000
1: Multi input 7
(S9) is ON.
1: Multi input 8
(S10) is ON.
1: Multi input 9
(S11) is ON.
1: Multi input 10
(S12) is ON.

Output ter- Shows output ON/OFF status.

minal status U1-11= 00000000
1: Multi-function
contact output
(M1-M2) is ON.
1: Multi-funtion
contact output 1
(P1) is ON.
1: Multi-funtion
contact output 2
U1-11 (P2) is ON.
(Cannot be output.) - A A A A A 4AH
输出端子状 1: Multi-function
态 contact output 3
(P3) is ON.
1: Multi-function
contact output 4
(P4) is ON.
Not used (always 0).
1: Error output
(MA/AB-MC) is ON.

Operation Inverter operating status.

status U1-12= 00000000
1: Run
1: Zero speed
1: Reverse
1: Reset signal
U1-12 input (Cannot be output.) - A A A A A 4BH
1: Speed agree
运行状态
1: Inverter
ready
1: Minor fault

1: Major fault

5-78
 User Constant Tables

Name Control Methods

Con- Output Signal Level Open Open MEMO-
Min. V/f Loop Flux Loop BUS
stant Description During Multi-Function Unit
Number Display V/f with Vec- Vec- Vec- Regis-
Analog Output PG tor tor tor ter
1 2
Cumulative Monitors the total operating
operation time of the Inverter.
time The initial value and the oper- 1
U1-13 (Cannot be output.) A A A A A 4CH
ating time/power ON time hr
累积时间 selection can be set in o2-07
and o2-08.
Software
No. (flash
U1-14 memory) (Manufacturer’s ID number) (Cannot be output.) - A A A A A 4DH

软件编号

Terminal Monitors the input voltage of

A1 input the voltage frequency refer- 10 V: 100% (10 V) 0.1
U1-15 voltage A A A A A 4EH
ence. An input of 10 V corre- (-10 to 10 V possible) %
端子 A1 电压 sponds to 100%.

Terminal Monitors the input current of

A2 input the multi-function analog 20 mA: 100% (4 to 20 mA)
current 0.1
U1-16 input. (0 to 10 V, -10 to 10 V possi- A A A A A 4FH
(voltage) %
An input of 20 mA corre- ble)
端子 A2 电压 sponds to 100%.

Terminal Monitors the input voltage of

A3 input the multi-function analog
10 V: 100% (10 V) 0.1
U1-17 voltage input. A A A A A 050H
(-10 to 10 V possible) %
An input of 10 V corresponds
端子 A3 电压 to 100%.

Motor sec- Monitors the calculated value

ondary cur- of the motor secondary cur- 10 V: Motor rated
rent (Iq) 0.1
U1-18 rent. secondary current) A A A A A 51H
%
电机 2 次电
The motor rated secondary (-10 to 10 V output)
流 current corresponds to 100%.

Motor Monitors the calculated value

exciting of the motor excitation cur-
10 V: Motor rated
current (Id) rent. 0.1
U1-19 secondary current) No No A A A 52H
The motor rated secondary %
电机励磁电
(-10 to 10 V output)
current corresponds to 100%.
流

Output fre- Monitors the output frequency

quency after a soft start.
after soft- The frequency given does not 10 V: Max. frequency 0.01
U1-20 start A A A A A 53H
include compensations, such (-10 to 10 V possible) Hz
软起动输出
as slip compensation.
频率 The unit is set in o1-03.

ASR input Monitors the input to the speed

control loop. 10 V: Max. frequency 0.01
U1-21 速度控制输
No A No A A 54H
The maximum frequency cor- (-10 to 10 V possible) %
入 responds to 100%.

ASR output Monitors the output from the

10 V: Motor rated
speed control loop. 0.01
U1-22 速度控制输 The motor rated secondary
secondary current) No A No A A 55H
%
出 (-10 to 10 V possible)
current corresponds to 100%.

PID feed- Monitors the feedback value

back value when PID control is used. 10 V: Max. frequency 0.01
U1-24 A A A A A 57H
The input for the max. fre- (-10 to 10 V possible) %
PID 反馈 quency corresponds to 100%.

5-79
 Name Control Methods
Con- Output Signal Level Open Open MEMO-
Min. V/f Loop Flux Loop BUS
stant Description During Multi-Function Unit
Number Display V/f with Vec- Vec- Vec- Regis-
Analog Output PG tor tor tor ter
1 2
DI-16H2 Monitors the reference value
input status from a DI-16H2 Digital Refer-
ence Board.
U1-25 (Cannot be output.) - A A A A A 58H
DI16 指令状
The value will be displayed in
态 binary or BCD depending on
user constant F3-01.
Output volt-
age refer- Monitors the Inverter internal
ence (Vq) 10 V: 200 VAC (400 VAC) 0.1
U1-26 voltage reference for motor No No A A A 59H
(-10 to 10 V possible) V
输出电压
secondary current control.
（Vq）

Output volt-
age refer- Monitors the Inverter internal
ence (Vd) 10 V: 200 VAC (400 VAC) 0.1
U1-27 voltage reference for motor No No A A A 5AH
(-10 to 10 V possible) V
输出电压
excitation current control.
（Vd）

Software
No. (CPU) (Manufacturer’s CPU software
U1-28 (Cannot be output.) - A A A A A 5BH
CPU 软件编
No.)
号

Output Monitors the Inverter’s output

power power. The display is split into
lower 4 dig- upper digits and lower digits in 0.1
U1-29 kWH
A A A A A 5CH
its the following way.

KWH 后 4 位  . kWH

U1-30 U1-29
Output (Cannot be output.)
power Example: If the output power
upper 5 dig- is 12345678.9 kWh, the dis-
U1-30 its play will be as follows: MWH A A A A A 5DH
U1-29: 678.9 kWH
KWH 前 5 位
U1-30: 12345 MWH
Range: 0.0 to 32767999.9

ACR out-
put of q axis Monitors the current control 10 V: 100% 0.1
U1-32 output value for the motor sec- No No A A A 5FH
Q 轴 ACR 输
(-10 to 10 V possible) %
ondary current.
出

ACR out-
put of d axis Monitors the current control 10 V: 100% 0.1
U1-33 output value for the motor No No A A A 60H
D 轴 ACR 输
(-10 to 10 V possible) %
excitation current.
出

OPE fault
constant Shows the first constant num-
U1-34 ber where an OPE fault was - A A A A A 61H
OPE 故障参 detected.
数

Zero-servo (Cannot be output.)

movement Shows the number of PG
pulses pulses times 4 for the move-
U1-35 1 No No No A No 62H
ment range when stopped at
零伺服移动 zero.
脉冲

PID input
volume PID feedback volume
10 V: Max. frequency 0.01
U1-36 Given as maximum frequency/ A A A A A 63H
PID 的输入
(-10 to 10 V possible) %
100%
量

5-80
 User Constant Tables

Name Control Methods

Con- Output Signal Level Open Open MEMO-
Min. V/f Loop Flux Loop BUS
stant Description During Multi-Function Unit
Number Display V/f with Vec- Vec- Vec- Regis-
Analog Output PG tor tor tor ter
1 2
PID output
volume PID control output
10 V: Max. frequency 0.01
U1-37 Given as maximum frequency/ A A A A A 64H
PID 的输出
(-10 to 10 V possible) %
100%
量

PID target PID target value

value 0.01
U1-38 Given as maximum frequency/ 10 V: Max. frequency A A A A A 65H
%
PID 目标值 100%

MEMOBUS Shows MEMOBUS errors.

communi- U1-39= 00000000
cations 1: CRC error
error code 1: Data length error
Not used (always 0).
1: Parity
U1-39 error (Cannot be output.) - A A A A A 66H
1: Overrun
通信错误代 error
码 1: Framing
error
1: Timeout
Not used (always 0).

Cooling fan
operating Monitors the total operating
time 1
U1-40 time of the cooling fan. The (Cannot be output.) A A A A A 68H
hr
风扇运行时
time can be set in 02-10.
间

Estimated Monitors the calculated value

motor flux of the motor flux. 100% is dis- 0.1
U1-42 10 V: Rated motor flux No No No No A 69H
played for the rated motor %
电机磁通量 flux.

Motor flux
current Monitors motor flux current
compensa- 10 V: Rated secondary cur-
compensation value. 100% is 0.1
U1-43 tion rent of motor No No No No A 6AH
displayed for the rated second- %
(-10 V to 10 V)
励磁电流补
ary current of the motor.
偿

ASR out-
put without Monitors the output from the
filter speed control loop (i.e., the 10 V: Rated secondary cur-
0.01
U1-44 primary filter input value). rent of motor No No No A A 6BH
%
反馈控制输
100% is displayed for rated (-10 V to 10 V)
出 secondary current of the
motor.

Feed for- Monitors the output from feed

ward con- 10 V: Rated secondary cur-
forward control. 100% is dis- 0.01
U1-45 trol output rent of motor No No No A A 6CH
played for rated secondary %
(-10 V to 10 V)
正反馈输出 current of the motor.

Stable
speed for Monitors the minimum speed
regenera- for which the speed will not
0.01
U1-48 tion exceed the speed reference in a 0.00 to 20.00 No No No No A 6FH
Hz
steady state during 100% load
再生时稳定 regeneration.
速度

5-81
 Name Control Methods
Con- Output Signal Level Open Open MEMO-
Min. V/f Loop Flux Loop BUS
stant Description During Multi-Function Unit
Number Display V/f with Vec- Vec- Vec- Regis-
Analog Output PG tor tor tor ter
1 2
CF error Monitors the CF error code.
code 00: No deceleration for 3 s
after Stop Command
01: Magnetic flux calculation
error
02: Startup status fault
U1-50 04: Speed estimator gain 0 to FFFF H No No No No A 71H
CF 故障报警 adjustment fault
代码 08: Low-speed regeneration
fault
10: Zero-speed fault
20: Rotation direction limit
fault

Electrolytic For maintenance purposes,

capacitor this timer shows the amount of
mainte- time the electrolytic capacitors
U1-61 nance (Cannot be output.) 1% A A A A A 7CH
have been operating. Capaci-
电容维护时
tors should be replaced when
期 the monitor reaches 100%.

Cooling fan This monitor displays the

mainte- amount of time the cooling fan
U1-63 nance has been operating. Replace (Cannot be output.) 1% A A A A A 7EH
the cooling fan when the dis-
冷却扇维护 play reads 100%.

Peak hold Displays the peak value of the 10V: Inverter rated output
current 0.01
current during run. “Peak current
U1-83 A A A A A A 7CFH
峰值保持电
Hold” refers to the moment (-10 to 10 V absolute value
*1
流 that the peak value is saved. output)

Output
frequency
during Displays the frequency value 0.01
10V: Max frequency
U1-84 peak hold when the output current Hz A A A A A 7DOH
(-10 to 10 V)
reached its peak value. *2
峰值保持输
出频率

* 1. The minimum unit differs depending on the Inverter capacity. (0.01 A for Inverter of 0.4 kW to 7.5 kW, and 0.1 A for Inverter of 11 kW or more)
* 2. The setting unit can be selected in o1-03.

5-82
 User Constant Tables

„Fault Trace: U2
User constants for error tracing are shown in the following table.
Name Control Methods
Output Signal
Con- Open Open MEMO-
Level During Min. V/f Loop Flux Loop BUS
stant Description
Number Display Multi-Function Unit V/f with Vec- Vec- Vec- Regis-
PG tor tor tor ter
Analog Output
1 2
Current fault
U2-01 The contents of the current fault. - A A A A A 80H
当前故障

Previous fault The contents of the error that

U2-02 occurred just prior to the current - A A A A A 81H
过去故障 fault.
Reference
frequency at The reference frequency when 0.01
U2-03 fault A A A A A 82H
the previous fault occurred. Hz
预先设定指令

Output fre-
quency at The output frequency when the 0.01
U2-04 fault A A A A A 83H
previous fault occurred. Hz
输出频率

Output cur-
rent at fault The output current when the pre-
U2-05 0.1 A A A A A A 84H
vious fault occurred.
输出电流

Motor speed (Cannot be output.)

at fault The motor speed when the previ- 0.01
U2-06 No A A A A 85H
ous fault occurred. Hz
电机速度

Output volt-
age reference The output reference voltage
U2-07 at fault 0.1 V A A A A A 86H
when the previous fault occurred.
故障输出电压

DC bus volt-
age at fault The main current DC voltage
U2-08 1V A A A A A 87H
主回路直流电
when the previous fault occurred.
压

Output power
at fault The output power when the pre- 0.1
U2-09 A A A A A 88H
vious fault occurred. kW
输出功率

Torque refer- The reference torque when the

ence at fault previous fault occurred. The
U2-10 0.1% No No A No A 89H
motor rated torque corresponds
转矩指令 to 100%.

5-83
 Name Control Methods
Output Signal
Con- Open Open MEMO-
Level During Min. V/f Loop Flux Loop BUS
stant Description Unit
Number Display Multi-Function V/f with Vec- Vec- Vec- Regis-
PG tor tor tor ter
Analog Output
1 2
Input termi- The input terminal status when
nal status at the previous fault occurred.
U2-11 fault - A A A A A 8AH
The format is the same as for U1-
输入端子状态
10.

Output termi-
nal status at The output terminal status when
U2-12 fault the previous fault occurred. The - A A A A A 8BH
format is the same as for U1-11.
输出端子状态

Operation The operating status when the

U2-13 status at fault previous fault occurred. The for- - A A A A A 8CH
运行状态 mat is the same as for U1-12.

Cumulative
operation (Cannot be output.)
The operating time when the pre- 1
U2-14 time at fault A A A A A 8DH
vious fault occurred. hr
累积时间

Peak hold
current at Displays the peak hold current 0.01
U2-21 fault A A A A A 7E6H
when the last fault occurred. A*
峰值保持电流

Peak hold
output Displays the frequency value at
frequency at the moment the current reached 0.01
U2-22 fault A A A A A 7E7H
its peak value when the last fault Hz
峰值保持输出
occurred.
频率

Note 1. The following errors are not included in the error trace: CPF00, 01, 02, 03, UV1, and UV2.
2. If the PUF fault is already indicated in U2-†† or U3-††, even if the PUF fault is detected again, the fault trace is not updated.
* The minimum unit differs depending on the Inverter capacity. (0.01 A for Inverter of 0.4 kW to 7.5 kW, and 0.1 A for Inverter of 11 kW or more)

5-84
 User Constant Tables

„Fault History: U3
User constants for the error log are shown in the following table.
Name Control Methods
Con- Output Signal Level Open Open MEMO-
Min. V/f Loop Flux -loop BUS
stant Description During Multi-Function Unit
Number Display V/f with Vec- Vec- Vec- Regis-
Analog Output PG tor tor tor ter
1 2
Most recent
fault The error contents of 1st
U3-01 - A A A A A 90H
previous fault.
1 次前故障

Second most
recent fault The error contents of 2nd
U3-02 - A A A A A 91H
previous fault.
2 次前故障

Third most
recent fault The error contents of 3rd
U3-03 - A A A A A 92H
previous fault.
3 次前故障

Fourth/oldest
fault The error contents of 4th
U3-04 - A A A A A 93H
previous fault.
4 次前故障

Cumulative
operation The total operating time
time at fault 1
U3-05 when the 1st previous fault A A A A A 94H
hr
故障累积时间
occurred. (Cannot be output.)
1

Accumulated
time of sec- The total operating time
ond fault 1
U3-06 when the 2nd previous fault A A A A A 95H
hr
故障累积时间
occurred.
2

Accumulated
time of third The total operating time
fault 1
U3-07 when the 3rd previous fault A A A A A 96H
hr
故障累积时间
occurred.
3

Accumulated
time of
fourth/oldest The total operating time
1
U3-08 fault when the 4th previous fault A A A A A 97H
hr
occurred.
故障累积时间
4

Note The following errors are not recorded in the error log: CPF00, 01, 02, 03, UV1, and UV2.

5-85
 ‹ Factory Settings that Change with the Control Method (A1-02)
The factory settings of the following user constants will change if the control method (A1-02) is changed.
Name Factory Setting
Con- Open- Open
stant Setting Range Unit V/f V/f with loop Flux Loop
Number Display Control PG Vector Vector Vector
1 2
Speed search selection
b3-01 0 to 3 1 2 3 2 - 2
起动速度搜索

Speed search operating current

b3-02 0 to 200 1% 120 - 100 - 10
速度搜索电流

Energy-saving gain
b8-02 0.0 to 10.0 0.1 - - 0.7 1.0 0.7
节能增益

Energy-saving filter time constant

b8-03 0.0 to 10.00 0.01 s - - 0.50 0.01 0.50
节能滤波 时间

Slip compensation gain

C3-01 0.0 to 2.5 0.1 0.0 - 1.0 1.0 1.0
滑差补偿增益

Slip compensation primary delay time

C3-02 0 to 10000 1 ms 2000 - 200 - -
滑差补偿时间

Torque compensation primary delay time

constant 200 200
C4-02 0 to 10000 1 ms 20 - -
*5 *5
转矩补偿延迟时间

ASR proportional (P) gain 1

C5-01 0.00 to 300.00 0.01 - 0.20 - 20.00 10.00
比例增益 1

ASR integral (I) time

C5-02 0.000 to 10.000 0.001 s - 0.200 - 0.500 0.500
积分时间 1

ASR proportional (P) gain 2

C5-03 0.00 to 300.00 0.01 - 0.02 - 20.00 10.00
比例增益 2

ASR integral (I) time 2 0.001

C5-04 0.000 to 10.000 - 0.050 - 0.500 0.500
积分时间 2 sec.

ASR primary delay time

C5-06 0.000 to 0.500 0.001 - - - 0.004 0.035
ASR 延迟时间

Carrier frequency selection

C6-02 1 to F*6 - 6*7 6*7 6*7 1*7 1*7
载波频率选择

Torque reference delay time

d5-02 0 to 1000 1 ms - - - 0 10
转矩控制延迟时间

E1-04 Max. output frequency (FMAX) 50.0 50.0

E3-02 0.0 to 400.0*4 0.1 Hz
*3 *3
50.0 50.0 50.0
最高输出频率

E1-05 Max. voltage (VMAX) 200.0 200.0

0.0 to 255.0 0.1 V 200.0 200.0 200.0
E3-03 最大电压 *3 *3

E1-06 Base frequency (FA) 50.0 50.0

0.0 to 400.0 0.1 Hz 50.0 50.0 50.0
E3-04 基本频率 *3 *3

E1-07 Mid. output frequency (FB) 2.5 2.5

0.0 to 400.0 0.1 Hz 3.0 0.0 0.0
E3-05 中间频率 *3 *3

5-86
 User Constant Tables

Name Factory Setting

Con- Open- Open
stant Setting Range Unit V/f V/f with loop Flux Loop
Number Display Control PG Vector Vector Vector
1 2

E1-08 Mid. output frequency voltage (VC)*2 0.0 to 255.0 15.0 15.0
0.1 V 13.2 0.0 0.0
E3-06 (0.0 to 510.0) *3 *3
中间电压

E1-09 Min. output frequency (FMIN) 1.2 1.2

0.0 to 400.0 0.1 Hz 0.5 0.0 0.3
E3-07 最低输出频率 *3 *3

E1-10 Min. output frequency voltage (VMIN)*2 0.0 to 255.0 9.0 9.0
0.1 V 2.4 - -
E3-08 (0.0 to 510.0) *3 *3
最低输出电压

Overspeed detection delay time

F1-09 0.0 to 2.0 0.1 s - 1.0 - 0.0 0.0
OS 过速检出时间

Feedforward control selection

N5-01 0, 1 1 - - - 0 1
FF 控制选择

* 1. The settings will be 0.05 (Flux vector)/1.00 (open-loop vector) for Inverters of 45kW or larger.
* 2. The settings shown are for 200 V Class Inverters. The values will double for 400 V Class Inverters.
* 3. Settings vary as shown in the following tables depending on the Inverter capacity and E1-03.
* 4. The setting range for open-loop vector 2 control is 0 to 132.0.
* 5. 1000 ms for Inverters of 200 V Class 30 to 110 kW and 400 V Class 55 to 300 kW.
* 6. The setting range depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given.
* 7. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given.

„200 V and 400 V Class Inverters of 0.4 to 1.5 kW

Con- Open Open

stant
Num-
Unit Factory Setting Loop
Vector
Loop
Vector
Flux
Vector
Con- Con- Con-
ber trol trol trol
E1-03 - 0 1 2 3 4 5 6 7 8 9 A B C D E F 1 2

E1-04 Hz 50.0 60.0 60.0 72.0 50.0 50.0 60.0 60.0 50.0 50.0 60.0 60.0 90.0 120.0 180.0 50.0 50.0 50.0 50.0

E1-05
V 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0
*
E1-06 Hz 50.0 60.0 50.0 60.0 50.0 50.0 60.0 60.0 50.0 50.0 60.0 60.0 60.0 60.0 60.0 50.0 50.0 50.0 0.0

E1-07 Hz 2.5 3.0 3.0 3.0 25.0 25.0 30.0 30.0 2.5 2.5 3.0 3.0 3.0 3.0 3.0 2.5 3.0 3.0 0.0

E1-08
V 15.0 15.0 15.0 15.0 35.0 50.0 35.0 50.0 19.0 24.0 19.0 24.0 15.0 15.0 15.0 15.0 13.2 15.9 0.0
*
E1-09 Hz 1.3 1.5 1.5 1.5 1.3 1.3 1.5 1.5 1.3 1.3 1.5 1.5 1.5 1.5 1.5 1.2 0.5 0.3 0.0

E1-10
V 9.0 9.0 9.0 9.0 8.0 9.0 8.0 9.0 11.0 13.0 11.0 15.0 9.0 9.0 9.0 9.0 2.4 1.5 0.0
*

* The settings shown are for 200 V Class Inverters. The values will double for 400 V Class Inverters.

„200 V and 400 V Class Inverters of 2.2 to 45 kW

Con- Open Open

stant
Num-
Unit Factory Setting Loop
Vector
Loop
Vector
Flux
Vector
Con- Con- Con-
ber trol trol trol
E1-03 - 0 1 2 3 4 5 6 7 8 9 A B C D E F 1 2

E1-04 Hz 50.0 60.0 60.0 72.0 50.0 50.0 60.0 60.0 50.0 50.0 60.0 60.0 90.0 120.0 180.0 50.0 50.0 50.0 50.0

E1-05
V 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0
*
E1-06 Hz 50.0 60.0 50.0 60.0 50.0 50.0 60.0 60.0 50.0 50.0 60.0 60.0 60.0 60.0 60.0 50.0 50.0 50.0 0.0

E1-07 Hz 2.5 3.0 3.0 3.0 25.0 25.0 30.0 30.0 2.5 2.5 3.0 3.0 3.0 3.0 3.0 2.5 3.0 3.0 0.0

E1-08
V 14.0 14.0 14.0 14.0 35.0 50.0 35.0 50.0 18.0 23.0 18.0 23.0 14.0 14.0 14.0 14.0 13.2 15.9 0.0
*
E1-09 Hz 1.3 1.5 1.5 1.5 1.3 1.3 1.5 1.5 1.3 1.3 1.5 1.5 1.5 1.5 1.5 1.2 0.5 0.3 0.0

5-87
 Con- Open Open
stant
Num-
Unit Factory Setting Loop
Vector
Loop
Vector
Flux
Vector
Con- Con- Con-
ber trol trol trol
E1-03 - 0 1 2 3 4 5 6 7 8 9 A B C D E F 1 2

E1-10
V 7.0 7.0 7.0 7.0 6.0 7.0 6.0 7.0 9.0 11.0 9.0 13.0 7.0 7.0 7.0 7.0 2.4 1.5 0.0
*

* The settings shown are for 200 V Class Inverters. The values will double for 400 V Class Inverters.

„200 V Class Inverters of 55 to 110 kW and 400 V Class Inverters of 55 to 300 kW

Con- Open Open

stant
Num-
Unit Factory Setting Loop
Vector
Loop
Vector
Flux
Vector
Con- Con- Con-
ber trol trol trol
E1-03 - 0 1 2 3 4 5 6 7 8 9 A B C D E F 1 2

E1-04 Hz 50.0 60.0 60.0 72.0 50.0 50.0 60.0 60.0 50.0 50.0 60.0 60.0 90.0 120.0 180.0 50.0 50.0 50.0 50.0

E1-05
V 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0
*
E1-06 Hz 50.0 60.0 50.0 60.0 50.0 50.0 60.0 60.0 50.0 50.0 60.0 60.0 60.0 60.0 60.0 50.0 50.0 50.0 0.0

E1-07 Hz 2.5 3.0 3.0 3.0 25.0 25.0 30.0 30.0 2.5 2.5 3.0 3.0 3.0 3.0 3.0 2.5 3.0 3.0 0.0

E1-08
V 12.0 12.0 12.0 12.0 35.0 50.0 35.0 50.0 15.0 20.0 15.0 20.0 12.0 12.0 12.0 12.0 13.2 15.9 0.0
*
E1-09 Hz 1.3 1.5 1.5 1.5 1.3 1.3 1.5 1.5 1.3 1.3 1.5 1.5 1.5 1.5 1.5 1.2 0.5 0.3 0.0

E1-10
V 6.0 6.0 6.0 6.0 5.0 6.0 5.0 6.0 7.0 9.0 7.0 11.0 6.0 6.0 6.0 6.0 2.4 1.5 0.0
*

* The settings shown are for 200 V Class Inverters. The values will double for 400 V Class Inverters.

5-88
 User Constant Tables

‹ Factory Settings that Change with the Inverter Capacity (o2-04)

The factory settings of the following user constants will change if the Inverter capacity (o2-04) is changed.

„200 V Class Inverters

Con-
stant Name Unit Factory Setting
Number
- Inverter Capacity
E2-11 Motor Rated Capacity
kW 0.4 0.75 1.5 2.2 3.7 5.5 7.5 11 15
2nd Motor Rated
E4-07
Capacity
o2-04 kVA selection - 0 1 2 3 4 5 6 7 8
Energy-saving filter time
b8-03 s 0.50 (Open-loop vector control)
constant

b8-04 Energy-saving coefficient - 288.20 223.70 169.40 156.80 122.90 94.75 72.69 70.44 63.13

Carrier frequency selec-

C6-02 - 6 6 6 6 6 6 6 6 6
tion*1

Carrier frequency selection

C6-11 for open-loop vector 2 con- - 1 1 1 1 1 1 1 1 1
trol*2

Carrier frequency selection

- - 6 6 6 6 6 6 6 6 6
upper limit

E2-01
Motor rated current A 1.90 3.30 6.20 8.50 14.00 19.60 26.60 39.7 53.0
(E4-01)

E2-02
Motor rated slip Hz 2.90 2.50 2.60 2.90 2.73 1.50 1.30 1.70 1.60
(E4-02)

E2-03
Motor no-load current A 1.20 1.80 2.80 3.00 4.50 5.10 8.00 11.2 15.2
(E4-03)

E2-05 Motor line-to-line resis-

Ω 9.842 5.156 1.997 1.601 0.771 0.399 0.288 0.230 0.138
(E4-05) tance

E2-06
Motor leak inductance % 18.2 13.8 18.5 18.4 19.6 18.2 15.5 19.5 17.2
(E4-06)

Motor iron loss for torque

E2-10 W 14 26 53 77 112 172 262 245 272
compensation

Momentary power loss ride-

L2-02 s 0.1 0.2 0.3 0.5 1.0 1.0 1.0 2.0 2.0
thru time
L2-03 Min. baseblock (BB) time s 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0

L2-04 Voltage recovery time s 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.6

L8-02 Overheat pre-alarm level °C 95 95 100 95 95 95 95 90 100

L8-39 Reduced carrier frequency kHz 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0

Hunting-prevention time
N1-03 ms 10 10 10 10 10 10 10 10 10
constant

N5-02 Motor acceleration time s 0.178 0.142 0.166 0.145 0.154 0.168 0.175 0.265 0.244

5-89
 Con-
stant Name Unit Factory Setting
Number
- Inverter Capacity
E2-11 Motor Rated Capacity
kW 18.5 22 30 37 45 55 75 90 110
2nd Motor Rated
E4-07
Capacity
o2-04 kVA selection - 9 A B C D E F 10 11
Energy-saving filter time
b8-03 s 0.50 (Open-loop vector control) 2.00 (Open-loop vector control)
constant

b8-04 Energy-saving coefficient - 57.87 51.79 46.27 38.16 35.78 31.35 23.10 20.65 18.12
C6-02 Carrier frequency selection - 6 4 4 4 4 4 4 1 1

Carrier frequency selection

C6-11 for open-loop vector 2 con- - 1 1 1 1 1 1 1 1 1
trol*2

Carrier frequency selection

- - 6 6 4 4 4 4 4 1 1
upper limit

E2-01
Motor rated current A 65.8 77.2 105.0 131.0 160.0 190.0 260.0 260.0 260.0
(E4-01)

E2-02
Motor rated slip Hz 1.67 1.70 1.80 1.33 1.60 1.43 1.39 1.39 1.39
(E4-02)

E2-03
Motor no-load current A 15.7 18.5 21.9 38.2 44.0 45.6 72.0 72.0 72.0
(E4-03)

E2-05 Motor line-to-line resis-

Ω 0.101 0.079 0.064 0.039 0.030 0.022 0.023 0.023 0.023
(E4-05) tance

E2-06
Motor leak inductance % 20.1 19.5 20.8 18.8 20.2 20.5 20.0 20.0 20.0
(E4-06)

Motor iron loss for torque

E2-10 W 505 538 699 823 852 960 1200 1200 1200
compensation

Momentary power loss ride-

L2-02 s 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0
thru time
L2-03 Min. baseblock (BB) time s 1.0 1.1 1.1 1.2 1.2 1.3 1.5 1.7 1.7

L2-04 Voltage recovery time s 0.6 0.6 0.6 0.6 1.0 1.0 1.0 1.0 1.0

L8-02 Overheat pre-alarm level °C 90 90 95 100 100 110 100 110 110

L8-39 Reduced carrier frequency kHz 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0

Hunting-prevention time
N1-03 ms 10 10 10 10 10 10 10 100 100
constant

N5-02 Motor acceleration time s 0.317 0.355 0.323 0.320 0.387 0.317 0.533 0.592 0.646
Note Attach a Momentary Power Interruption Compensation Unit if compensation for power interruptions of up to 2.0 seconds is required for 200 V Class
Inverters with outputs of 0.4 to 7.5 kW.
* 1. The initial settings for C6-02 are as follows: 0: Low noise PWM, 1: 2.0 kHz, 2: 5.0 kHz, 3: 8.0 kHz, 4: 10.0 kHz, 5: 12.5 kHz, and 6: 15.0 kHz. If the
carrier frequency is set higher than the factory setting for Inverters with outputs of 5.5 kW or more, the Inverter rated current will need to be reduced.
* 2. The initial settings for C6-11 are as follows: 1: 2.0 kHz, 2: 4.0 kHz, 3: 6.0 kHz, 4: 8.0 kHz.

5-90
 User Constant Tables

„400 V Class Inverters

Con-
stant
Name Unit Factory Setting
Num-
ber
- Inverter Capacity
Motor Rated
E2-11
Capacity kW 0.4 0.75 1.5 2.2 3.7 4.0 5.5 7.5 11 15
2nd Motor Rated
E4-07
Capacity
o2-04 kVA selection - 20 21 22 23 24 25 26 27 28 29
Energy-saving filter time
b8-03 s 0.50 (Open-loop vector control)
constant

b8-04 Energy-saving coefficient - 576.40 447.40 338.80 313.60 245.80 236.44 189.50 145.38 140.88 126.26
Carrier frequency selec-
C6-02 - 3 3 3 3 3 3 3 3 3 3
tion*1
Carrier frequency selec-
C6-11 tion for open-loop vector - 1 1 1 1 1 1 1 1 1 1
2 control*2

Carrier frequency selec-

- - 3 3 3 3 3 3 3 3 3 3
tion upper limit
E2-01
Motor rated current A 1.00 1.60 3.10 4.20 7.00 7.00 9.80 13.30 19.9 26.5
(E4-01)

E2-02
Motor rated slip Hz 2.90 2.60 2.50 3.00 2.70 2.70 1.50 1.30 1.70 1.60
(E4-02)

E2-03
Motor no-load current A 0.60 0.80 1.40 1.50 2.30 2.30 2.60 4.00 5.6 7.6
(E4-03)
E2-05 Motor line-to-line resis-
Ω 38.198 22.459 10.100 6.495 3.333 3.333 1.595 1.152 0.922 0.550
(E4-05) tance

E2-06
Motor leak inductance % 18.2 14.3 18.3 18.7 19.3 19.3 18.2 15.5 19.6 17.2
(E4-06)

Motor iron loss for torque

E2-10 W 14 26 53 77 130 130 193 263 385 440
compensation
Momentary power loss
L2-02 s 0.1 0.2 0.3 0.5 0.5 0.8 0.8 1.0 2.0 2.0
ridethru time

L2-03 Min. baseblock (BB) time s 0.2 0.3 0.4 0.5 0.6 0.6 0.7 0.8 0.9 1.0

L2-04 Voltage recovery time s 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.6

L8-02 Overheat pre-alarm level °C 95 95 95 95 95 95 95 90 95 95

Reduced carrier
L8-39 kHz 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0
frequency

Hunting-prevention time
N1-03 ms 10 10 10 10 10 10 10 10 10 10
constant

N5-02 Motor acceleration time s 0.178 0.142 0.166 0.145 0.154 0.154 0.168 0.175 0.265 0.244

5-91
 Con-
stant Name Unit Factory Setting
Number
- Inverter Capacity
Motor Rated
E2-11
Capacity kW 18.5 22 30 37 45 55 75 90 110 132 160 185 220 300
2nd Motor Rated
E4-07
Capacity
o2-04 kVA selection - 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37
Energy-saving filter
b8-03 s 0.50 (Open-loop vector control) 2.00 (Open-loop vector control)
time constant

Energy-saving coeffi-
b8-04 - 115.74 103.58 92.54 76.32 71.56 67.20 46.20 38.91 36.23 32.79 30.13 30.57 27.13 21.76
cient
Carrier frequency
C6-02 - 3 3 3 3 3 2 2 F F F*3 1 1 F*3 1
selection*1
Carrier frequency
C6-11 selection for open- - 1 1 1 1 1 1 1 1 1 1 1 1 1 1
loop vector 2 control*2

Carrier frequency
- - 3 3 3 3 3 2 2 3.0 3.0 1 1 1 1 1
selection upper limit

E2-01
Motor rated current A 32.9 38.6 52.3 65.6 79.7 95.0 130.0 156.0 190.0 223.0 270.0 310.0 370.0 500.0
(E4-01)
E2-02
Motor rated slip Hz 1.67 1.70 1.80 1.33 1.60 1.46 1.39 1.40 1.40 1.38 1.35 1.30 1.30 1.25
(E4-02)

E2-03
Motor no-load current A 7.8 9.2 10.9 19.1 22.0 24.0 36.0 40.0 49.0 58.0 70.0 81.0 96.0 130.0
(E4-03)

E2-05 Motor line-to-line

Ω 0.403 0.316 0.269 0.155 0.122 0.088 0.092 0.056 0.046 0.035 0.029 0.025 0.020 0.014
(E4-05) resistance

E2-06
Motor leak inductance % 20.1 23.5 20.7 18.8 19.9 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0
(E4-06)

Motor iron loss for

E2-10 W 508 586 750 925 1125 1260 1600 1760 2150 2350 2850 3200 3700 4700
torque compensation
Momentary power
L2-02 s 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0
loss ridethru time

Min. baseblock (BB)

L2-03 s 1.0 1.1 1.1 1.2 1.2 1.3 1.5 1.7 1.7 1.8 1.9 2.0 2.1 2.1
time

L2-04 Voltage recovery time s 0.6 0.6 0.6 0.6 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0

Overheat pre-alarm
L8-02 °C 95 95 95 95 95 100 105 105 120 110 115 100 110 115
level

Reduced carrier
L8-39 kHz 2.0 2.0 2.0 2.0 2.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
frequency
Hunting-prevention
N1-03 ms 10 10 10 10 10 30 30 30 30 30 30 100 100 100
time constant

Motor acceleration
N5-02 s 0.317 0.355 0.323 0.320 0.387 0.317 0.533 0.592 0.646 0.673 0.777 0.864 0.910 1.392
time

Note Attach a Momentary Power Interruption Compensation Unit if compensation for power interruptions of up to 2.0 seconds is required for 400 V Class Inverters
with outputs of 0.4 to 7.5 kW.
* 1. The initial settings for C6-02 are as follows: 1: 2.0 kHz, 2: 5.0 kHz, 3: 8.0 kHz, 4: 10.0 kHz, 5: 12.5 kHz, 6: 15.0 kHz, and F: optional setting (initial value for
Inverters of 90 or 110 kW: 3.0 kHz).
* 2. The initial settings for C6-11 are as follows: 1: 2.0 kHz, 2: 4.0 kHz, 3: 6.0 kHz, 4: 8.0 kHz.
* 3. The factory setting for 400V 132kW and 220kW flax vector control (A1-02 = 3) is 1.5 kHz, for software version VSG123032 or later.

5-92
Constant Settings by
Function
Frequency Reference ..................................................6-2
Run Command...........................................................6-10
Stopping Methods ......................................................6-12
Acceleration and Deceleration Characteristics ..........6-18
Adjusting Frequency References...............................6-28
Speed Limit (Frequency Reference Limit Function)...6-34
Improved Operating Efficiency...................................6-36
Machine Protection ....................................................6-42
Continuing Operation.................................................6-63
Inverter Protection .....................................................6-74
Input Terminal Functions............................................6-76
Output Terminal Functions.........................................6-86
Monitor Constants......................................................6-88
Individual Functions ...................................................6-92
Digital Operator Functions .......................................6-148
Options ....................................................................6-158
Using Inverters for Elevating Machines ...................6-170
Current Alarm Function............................................6-181
Peak Hold Current Monitoring Function...................6-182
Maintenance Timer Display Function.......................6-183
 Frequency Reference
This section explains how to input the frequency reference.

‹ Selecting the Frequency Reference Source

Set constant b1-01 to select the frequency reference source.

„Related Constants

Name Control Methods

Change Open- Open MEMO-
Con-
Setting Factory during V/f loop Flux Loop BUS
stant Description Range Setting Opera- Regis-
Number Display V/f with Vec- Vec- Vec-
tion PG tor tor tor ter
1 2
Reference Set the frequency reference input
selection method.
0: Digital Operator
1: Control circuit terminal (analog
b1-01 0 to 4 1 No Q Q Q Q Q 180H
频率指令选
input)
择 2: MEMOBUS communications
3: Option board
4: Pulse train input

Pulse train
input func-
tion selec- 0: Frequency reference
H6-01 tion 1: PID feedback value 0 to 2 0 No A A A A A 42CH
2: PID target value
脉冲输入选
择

Pulse train
input scal- 1000
ing Set the number of pulses in hertz, tak- 1440
H6-02 to Yes A A A A A 42DH
ing the reference to be 100%. Hz
脉冲输入比
32000
例

„Input the Reference Frequency from the Digital Operator

When b1-01 is set to 0, you can input the reference frequency from the Digital Operator.
Input the reference frequency from the Digital Operator's reference frequency setting display.
For details on setting the reference frequency, refer to Chapter 3 Digital Operator and Modes.

'5,9( 5G\

乥⥛ᣛҸ
8 +]
Fig 6.1 Frequency Setting Display

6-2
 Frequency Reference

„Inputting the Frequency Reference Using Control Circuit Terminal (Analog Setting)
When b1-01 is set to 1, you can input the frequency reference from control circuit terminal A1 (voltage input),
or control circuit terminal A2 (voltage or current input).

Inputting Master Speed Frequency Reference Only (Voltage Input)

When inputting a voltage for the master speed frequency reference, input the voltage to control circuit termi-
nal A1.

Inverter

+V Power supply: 15 V,
20 mA
2 kΩ A1 Master speed frequency
reference
(voltage input)
A2 Master speed frequency
reference
(current input)
A3 Auxiliary speed frequency
reference 1
AC Analog common

Fig 6.2 Voltage Input for Master Speed Frequency Reference

Inputting Master Speed Frequency Reference Only (Current Input)

When inputting a current for the master speed frequency reference, input the current to control circuit terminal
A2, input 0 V to terminal A1, set H3-08 (Multi-function analog input terminal A2 signal level selection) to 2
(current input), and set H3-09 (Multi-function analog input terminal A2 function selection) to 0 (add to termi-
nal A1).

Inverter

+V Power supply: 15 V,
20 mA
Master speed frequency
A1
reference
4 to 20-mA input (voltage input)
A2 Master speed frequency
reference
(current input)
A3 Auxiliary speed frequency
reference 1
AC Analog common
1
DIP switch
2 S1
V I

Fig 6.3 Current Input for Master Speed Frequency Reference

Turn ON pin 2 of DIP switch S1 (toward I), the voltage/current switch, when inputting a current to terminal A2.
Turn OFF pin 2 of DIP switch S1 (toward V), the voltage/current switch, when inputting a voltage to terminal
A2. Set H3-08 to the correct setting for the type of input signal being used.
IMPORTANT

Switch between 2 Step Speeds: Master/Auxiliary Speeds

When switching between the master and auxiliary speeds, connect the master speed frequency reference to
control circuit terminal A1 or A2 and connect the auxiliary speed frequency reference to terminal A3. The ref-
erence on terminal A1 or A2 will be used for the Inverter frequency reference when the multi-function input
allocated to multi-speed command 1 is OFF and the reference on terminal A3 will be used when it is ON.

6-3
 When switching between the master and auxiliary speeds, set H3-05 (Multi-function analog input terminal
A3) to 2 (auxiliary frequency reference, 2nd step analog) and set on of the multi-function input terminals to
multi-step speed reference 1.
When inputting a current to terminal A2 for the master speed frequency reference, set H3-08 (Multi-function
analog input terminal A2 signal level selection) to 2 (current input), and set H3-09 (Multi-function analog
input terminal A2 function selection) to 0 (add to terminal A1).

Inverter
S5 Multi-step speed
reference 1

+V Power supply: 15 V,
20 mA

Master speed
2 kΩ A1 frequency reference
(voltage input)
Master speed
4 to 20 mA
A2 frequency reference
(current input)
2 kΩ A3 Auxiliary speed
frequency reference 1
AC Analog common

Fig 6.4 Switching between Master and Auxiliary Frequencies

„Setting Frequency Reference Using Pulse Train Signals

When b1-01 is set to 4, the pulse train input to control circuit terminal RP is used as the frequency reference.
Set H6-01 (Pulse Train Input Function Selection) to 0 (frequency reference), and then set the 100% reference
pulse frequency to H6-02 (Pulse Train Input Scaling).

Pulse Input Specifications Inverter

Low level voltage 0.0 to 0.8 V

High level voltage 3.5 to 13.2 V

32 kHz max.
Heavy duty 30 to 70% 3.5 to 13.2 V
RP(Pulse train input termi-
Pulse frequency 0 to 32 kHz Pulse input nal)
AC (Analog common)

Fig 6.5 Frequency Reference Using Pulse Train Input

6-4
 Frequency Reference

‹ Using Multi-Step Speed Operation

With Varispeed-G7 series Inverters, you can change the speed to a maximum of 17 steps, using 16 frequency
references, and one jog frequency reference.
The following example of a multi-function input terminal function shows a 9-step operation using multi-step
references 1 to 3 and jog frequency selection functions.

„Related Constants
To switch frequency references, set multi-step speed references 1 to 3 and the jog reference selection in the
multi-function contact inputs. Setting examples are shown below.

Multi-function Contact Inputs (H1-01 to H1-10)

Constant Set Value
Terminal Details
Number (Factory Setting)
Multi-step speed reference 1 (Also used for master speed/auxiliary speed switching when
S5 H1-03 3
multi-function analog input H3-05 is set to 2 (auxiliary frequency reference 1).)

Multi-step speed reference 2 [Also used for auxiliary frequency reference 2 when multi-
S6 H1-04 4
function analog input H3-09 is set to 3 (auxiliary frequency reference 2).]

S9 H1-07 5 Multi-step speed reference 3

S7 H1-05 6 Jog frequency selection (given priority over multi-step speed reference)

Combination of Multi-Function References and Multi-Function Contact Inputs

You can change the selected frequency reference by combining the ON/OFF status of S5 to S9 (multi-function
contact input terminals) to set multi-step speed references 1 to 3 and the jog frequency selection. The follow-
ing table shows the possible combinations.
TerminalS5 TerminalS6 TerminalS9 TerminalS7
Speed Multi-step Multi-step Multi-step Jog Fre- Selected Frequency
Speed Refer- Speed Refer- Speed Refer- quency Selec-
ence 1 ence 2 ence 3 tion
1 OFF OFF OFF OFF Frequency reference 1 d1-01, master speed frequency

2 ON OFF OFF OFF Frequency reference 2 d1-02, auxiliary frequency 1

3 OFF ON OFF OFF Frequency reference 3 d1-03, auxiliary frequency 2

4 ON ON OFF OFF Frequency reference 4 d1-04

5 OFF OFF ON OFF Frequency reference 5 d1-05

6 ON OFF ON OFF Frequency reference 6 d1-06

7 OFF ON ON OFF Frequency reference 7 d1-07

8 ON ON ON OFF Frequency reference 8 d1-08

9 - - - ON* Jog frequency d1-17

* Terminal S7's jog frequency selection is given priority over multi-step speed references.

6-5
 Setting Precautions
Refer to the following to set step 1 to step 3 to analog inputs.
• Step 1
When setting terminal A1's analog input to step 1, set b1-01 to 1, and when setting d1-01 (Frequency Ref-
erence 1) to step 1, set b1-01 to 0.
• Step 2
When setting terminal A3's analog input to step 2, set H3-05 to 2 (auxiliary frequency reference 1). When
setting d1-02 (Frequency Reference 2) to step 2, set H3-05 to 1F (Analog input not used).
• Step 3
When setting terminal A2's analog input to step 3, set H3-09 to 3 (auxiliary frequency reference 2). When
setting d1-03(Frequency Reference 3) to step 3, set H3-05 to 1F (Analog input not used).
When inputting 0 to 10 V to terminal A2’s analog input, set H3-08 to 0, and turn OFF pin 2 to DIP switch
S1 on the control circuit terminal board. (Refer to page 2-26.)

„Connection Example and Time Chart

The following diagram shows a time chart and control circuit terminal connection example during a 9-step
operation.

Inverter

S1 Forward/stop

S2 Reverse/stop

S3 External fault

S4 Fault reset

S5 Multi-step speed reference 1

S6 Multi-step speed reference 2

S9 Multi-step speed reference 3

S7 Jog frequency

SC Sequence common

+V Frequency setting power (+15 V)

A1 Master speed referennce (0 to 10 V)

[Master speed frequency (b1-01=1)]
A2 Master speed referennce (4 to 20 mA)
[Auxiliary speed frequency1 (H3-09=2)]
A3 Auxiliary speed frequency (0 to 10 V)
[Auxiliary speed frequency 2 (H3-05=3)]
AC Analog common 0 V

Fig 6.6 Control Circuit Terminal During 9-step Operation

6-6
 Frequency Reference

Frequency
reference 8
Frequency
reference 7
Frequency
reference 6
Frequency
reference 5
Frequency
reference 4
Frequency
Frequency reference 3:
reference Frequency ref- Auxiliary
erence 2: Auxil- speed fre-
iary speed quency 2
frequency 1
Frequency Jog frequency
reference 1:
Master speed
frequency

Forward/stop

Multi-step speed
reference 1

Multi-step speed
reference 2
Multi-step speed
reference 3
Jog frequency
selection

Fig 6.7 Multi-step speed reference/Jog Frequency Selection Time Chart

6-7
6-8
B1-01

C option board Pulse train input =4 d2-03

other than A1-14B Master frequency
L4-05 lower limit
F2-01 Process when
A1-14B frequency =1
refrence is Option
lost. =3 Remote
±13 bits Muluti-step speed reference
+ + H3-02 =1 =0 Local Inverter
Ch1 A/D H3-03 =0
=2 Multi-function
+ + Memobus Frequency analog input is invalid. Jog frequency
0V 10V =0 command (d1-17㧕
communication reference 1 When 2nd speed
±13 bits =1
(d1-01) analog is selected
=1
A/D Multi-function When FJOG, RJOG (Jog
Ch2 1/10 Frequency analog input is invalid.
reference 2 When 3rd speed frequency command) of
L4-05 =0 multi-function contact
d1-01
(d1-02) analog is selected =2
Process when input is input.
±13 bits frequency Frequency Multi-function
analog input is invalid.
refrence is =1 reference 3
Ch3 A/D X 1/10 lost. (d1-03)
Frequency
=0 Frequency =3 reference
reference 4
(d1-04)
H3-05 (Terminal A3) function
H3-09 (Terminal A2) function Frequency =4
reference 5
(d1-05)
AI input㧔See fig6.11㧕 Set- V/f Open Flux Frequency =5
‹ Varispeed G7 Function Block

ting Function V/f with Loop

Vec- Vec- Input Level reference 6
Value PG tor tor (d1-06)
=0
±11 bits Frequency =6
00 Add to terminal A1 Yes Yes Yes Yes ±100%/±10 V !reference
! ! ! 7
6GTOKPCN 1 A
A/D 01 Frequency gain Yes Yes Yes Yes 100%/10 V (d1-07)
A1 =1
Auxiliary frequency Frequency =7
02 reference 1 Yes Yes Yes Yes ±100%/±10 V reference 8
=0 (2nd step analog)
±11 bits (d1-08)
6GTOKPCN 2 B Auxiliary frequency
A/D 03 reference 2 Yes Yes Yes Yes ±100%/±10 V Frequency =8
A2 =1 reference 9
(3rd step analog)
(d1-09)
04 Voltage bias Yes Yes No No 100%/10 V
±11 bits =0 Accel/decel change Frequency =9
05 (reduction coefficient) Yes Yes Yes Yes 100%/1 V reference 10
6GTOKPCN 3 C (d1-10)
A/D =1 DC injection
A3 06 Yes Yes Yes No 100%/10 V
braking current Frequency = 10
Overtorque/undertorque reference 11
07 Yes Yes Yes Yes 100%/10 V (d1-11)
detection level
08 Stall prevention level Yes Yes No No 100%/10 V Frequency = 11
during run reference 12
F2-01 Frequency reference (d1-12)
09 Yes Yes Yes Yes 100%/10 V
lower limit level
Frequency = 12
The following diagram shows the function block diagram of Varispeed G7.

Note: If A1-14B is not mounted,

0A Jump frequency Yes Yes Yes Yes 100%/10 V reference 13
the same operation as when (d1-13)
F2-01=1 will be performed 0B PID feedback Yes Yes Yes Yes ±100%/±10 V
regardless of the F2-01 setting. Frequency = 13
0C PID target value Yes Yes Yes Yes ±100%/±10 V
reference 14
0D Frequency baias 2 Yes Yes Yes Yes ±100%/±10 V (d1-14)
0E Motor temperature input Yes Yes Yes Yes ±100%/±10 V Frequency = 14
reference 15
10 Positive toraue limit No No Yes Yes 100%/10 V (d1-15)
11 Negative torque limit No No Yes Yes 100%/10 V Frequency = 15
12 Regenerative torque No No Yes Yes 100%/10 V reference 16
limit (d1-16)
13 Torque refrence/torque No No No Yes ±100%/±10 V
limit at speed control
14 Torque compensation No No Yes Yes ±100%/±10 V
Positive/negative torque
15 limit No No Yes Yes 100%/10 V
1F Analog input not used. Yes Yes Yes Yes

Fig 6.8 Varispeed G7 Function Block

 Frequency Reference

*
*
Primary   #
 delay filter *
8 8

*

* *

*
Primary  
 delay filter * $
≠
8 8

*

* 2 is current input.

*
* 
*
Primary  
 *
%
delay filter
8 8 ≠

*

* The same value can not be set in H3-05 and H3-09.

Fig 6.9 AI Input Detailed Diagram

6-9
 Run Command
This section explains input methods for the Run Command.

‹ Selecting the Run Command Source

Set constant b1-02 to select the source for the Run Command.

„Related Constants

Name Control Methods

Change Open- Open MEMO-
Con-
Setting Factory during V/f loop Flux Loop BUS
stant Description Range Setting Opera- Regis-
Number Display V/f with Vec- Vec- Vec-
tion PG tor tor tor ter
1 2
Operation Set the Run Command input method
method 0: Digital Operator
selection 1: Control circuit terminal (sequence
b1-02 0 to 3 1 No Q Q Q Q Q 181H
input)
运行指令选 2: MEMOBUS communications
择 3: Option board

„Performing Operations Using a Digital Operator

When b1-02 is set to 0, you can perform Inverter operations using the Digital Operator keys (RUN, STOP,
JOG, and FWD/REV). For details on the Digital Operator, refer to Chapter 3 Digital Operator and Modes.

„Performing Operations Using Control Circuit Terminals

When b1-02 is set to 1, you can perform Inverter operations using the control circuit terminals.

Performing Operations Using a 2-wire Sequence

The factory setting is set to a 2-wire sequence. When control circuit terminal S1 is set to ON, forward opera-
tion will be performed, and when S1 is turned OFF, the Inverter will stop. In the same way, when control cir-
cuit terminal S2 is set to ON, reverse operation will be performed, and when S2 is turned OFF, the Inverter
will stop.

Inverter
Forward/stop

Reverse/stop

Sequence common

Fig 6.10 2-wire Sequence Wiring Example

6-10
 Run Command

Performing Operations Using a 3-wire Sequence

When any constant from H1-01 to H1-10 (multi-function contact input terminals S3 to S12) is set to 0, termi-
nals S1 and S2 are used for a 3-wire sequence, and the multi-function input terminal that has been set func-
tions as a Forward/Reverse Run Command terminal.
When the Inverter is initialized for 3-wire sequence control with A1-03, multi-function input 3 becomes the
input terminal for the Forward/Reverse Run Command.

Stop switch Operation switch

(NC contact) (NO contact)
Run Command
(operates when ON)
Stop Command
(stopped when ON)
Forward/Reverse Command
(multi-function input)
Sequence input common

Fig 6.11 3-wire Sequence Wiring Example

50 ms min.

Run Command Can be either ON or OFF

OFF
Stop Command (stopped)
Forward/Reverse OFF (forward) ON (reverse)
Command

Motor speed

Stop Forward Reverse Stop Forward

Fig 6.12 Three-wire Sequence Time Chart

1. Use a sequence that turns ON terminal S1 for 50 ms or longer for the Run Command. This will make the
Run Command self-holding in the Inverter.
2. When the 3-wire sequence is set, do not make the wiring for the control circuit unless the multi-function
input terminal constant is set. Failure to observe this warning may result in injury.
INFO

6-11
 Stopping Methods
This section explains methods of stopping the Inverter.

‹ Selecting the Stopping Method when a Stop Command is Sent

There are four methods of stopping the Inverter when a Stop Command is sent:
• Deceleration to stop
• Coast to stop
• DC braking stop
• Coast to stop with timer
Set constant b1-03 to select the Inverter stopping method. A DC braking stop and coasting to a stop with a
timer cannot be set for flux vector control.

„Related Constants

Name Control Methods

Change Open- Open MEMO-
Con-
Setting Factory during V/f loop Flux Loop BUS
stant Description Range Setting Opera- Regis-
Number Display V/f with Vec- Vec- Vec-
tion PG tor tor tor ter
1 2
Stopping Select stopping method when Stop
method Command is sent.
selection 0: Deceleration to stop
1: Coast to stop
2: DC injection braking stop (Stops
b1-03 0 to 3* 0 No Q Q Q Q Q 182H
faster than coast to stop, no
停止方法选 regenerative operation.)
择 3: Coast to stop with timer (Run
Commands are disregarded during
deceleration.)
Operation Used to set the method of operation
selection when the frequency reference input
for setting is less than the minimum output fre-
E1-09 or quency (E1-09).
less 0: Run at frequency reference (E1-09
not effective).
b1-05 0 to 3 0 No No No No A No 184H
1: STOP (Frequencies below E1-09
in the coast to stop state.)
不足最低频 2: Run at min. frequency.
率动作 (E1-09)
3: Run at zero-speed (Frequencies
below E1-09 are zero)

Zero-speed
level (DC Used to set the frequency which starts
injection DC injection braking in units of Hz
braking when deceleration to stop is selected. 0.0 to
b2-01 starting fre- 0.5 Hz No A A A A A 189H
When b2-01 is less than E1-09, E1-09 10.0
quency) becomes the DC injection braking
直流制动开
starting frequency.
始频率

DC injec-
tion brak- Sets the DC injection braking current
ing current 0 to
b2-02 as a percentage of the Inverter rated 50% No A A A No No 18AH
100
直流制动电
current.
流

6-12
 Stopping Methods

Name Control Methods

Change Open- Open MEMO-
Con-
Setting Factory during V/f loop Flux Loop BUS
stant Description Range Setting Opera- Regis-
Number Display V/f with Vec- Vec- Vec-
tion PG tor tor tor ter
1 2
DC injec- Used to set the time to perform DC
tion brak- injection braking at start in units of 1
ing time at second. 0.00
b2-03 start Used to stop coasting motor and to 0.00 s No A A A A A 18BH
restart it. When the set value is 0, DC 10.00
起动制动时 injection braking at start is not per-
间 formed.

DC injec- Used to set the time to perform DC

tion brak- injection braking at stop in units of 1
ing time at second. 0.00
b2-04 stop Used to prevent coasting after the to 0.50 s No A A A A A 18CH
Stop Command is input. When the set 10.00
停止制动时 value is 0.00, DC injection braking at
间 stop is not performed.
* 0 or 1 for flux vector control and open-loop vector 2 control.

„Deceleration to Stop
If the Stop Command is input (i.e., the Run Command is turned OFF) when b1-03 is set to 0, the motor decel-
erates to a stop according to the deceleration time that has been set. (Factory setting: C1-02 (Deceleration
Time 1))
If the output frequency when decelerating to a stop falls below b2-01, the DC injection brake will be applied
using the DC current set in b2-02 only for the time set in b2-04.
For deceleration time settings, refer to page 6-18 Setting Acceleration and Deceleration Times.

Run command
ON OFF

Output frequency
Decelerates to stop at
deceleration time
DC injection brake

DC injection brake time

when stopping (b2-04)

Fig 6.13 Deceleration to Stop

6-13
 The operation after stopping depends on the setting of b1-05 when flux vector control is selected (A1-02 = 3).

Run Command OFF ON OFF

Frequency reference
via analog input E1-09

Run Command turns OFF

and zero-speed control start
when motor speed drops to b2-01.
b1-05=0
(frequency reference) Zero speed
Injection brake
time at start control

Baseblock b2-03 Baseblock

b2-04
Frequency reference drops to less
than E1-09 and zero-speed control
b1-05=1 Injection brake Zero speed starts when motor speed drops to
(Coast) time at start control b2-01.

Baseblock b2-03 Baseblock

b2-04 Run Command turns OFF
b1-05=2 and zero-speed control start
when motor speed drops to b2-01.
(Run on E1-09) Injection brake
time at start Zero speed control

Baseblock Baseblock
b2-03 b2-04
Run Command turns OFF
b1-05=3 and zero-speed control start
(Zero-speed) Injection brake when motor speed drops to b2-01.
time at start Zero speed control

Baseblock b2-03 b2-04 Baseblock

Fig 6.14 Deceleration to Stop (for Flux Vector Control)

Setting Precautions
• When using flux vector control, the zero-speed control starts when motor speed drops to b2-01 during
deceleration. Also, the setting b2-01 < E1-09 is possible.
• The current level during injection brake time at start is the value of E2-03 (motor no-load current). Accord-
ingly, b2-02 is invalid in flux vector control.

„Coast to Stop
If the Stop Command is input (i.e., the Run Command is turned OFF) when b1-03 is set to 1, the Inverter out-
put voltage is interrupted. The motor coasts to a stop at the deceleration rate that counterbalances damage to
the machine and inertia including the load.

Run Command
ON OFF

Output frequency

Inverter output freqeuencty interrupted.

Fig 6.15 Coast to Stop

6-14
 Stopping Methods

After the Stop Command is input, Run Commands are ignored until the Minimum Baseblock Time (L2-03) has
elapsed.

INFO

„DC Braking Stop

If the Stop Command is input (i.e., the Run Command is turned OFF) when b1-03 is set to 2, a wait is made
for the time set in L2-03 (Minimum Baseblock (BB) Time) and then the DC injection brake current set in b2-
02 is sent to the motor to apply a DC injection brake to stop the motor. The DC injection brake time is deter-
mined by the set value in b2-04 and the output frequency when the Stop Command is input.

DC injection brake time

Run Command
ON OFF
b2-04 10
Output frequency

Inverter output voltage interrupted

DC injection brake

b2-04
Minimum baseblock DC injection brake time
time (L2-03) Output frequency at
Stop Command input
10 100% (maximum output frequency)

Fig 6.16 DC Injection Braking (DB) Stop

Lengthen the Minimum Baseblock Time (L2-03) when an overcurrent (OC) occurs during stopping.

INFO

„Coast to Stop with Timer

If the Stop Command is input (i.e., the Run Command is turned OFF) when b1-03 is set to 3, the Inverter out-
put is interrupted to coast the motor to a stop. After the Stop Command is input, Run Commands are ignored
until the time T has elapsed. The time T depends upon the output frequency when the Stop Command is input
and the deceleration time.

Run Command Operation wait time T

ON OFF ON OFF ON

Output Deceleration time

frequency (e.g., C1-02)

Inverter output voltage interrupted

Operation wait time T Minimum baseblock

time (L2-03)
Output frequency at
Stop Command input
Minimum output frequency 100% (Maximum output frequency)

Fig 6.17 Coast to Stop with Timer

6-15
 ‹ Using the DC Injection Brake
Set constant b2-03 to apply the DC injection braking current to the motor while it is coasting to a stop, to stop
the motor and then restart it.
Set b2-03 to 0 to disable the DC injection brake at start.
Set the DC injection brake current using b2-02. DC injection braking is used at startup for flux vector control
with the current set in E2-03 (Motor no-load current).

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
DC injection Sets the DC injection braking cur-
braking current 0 to
b2-02 rent as a percentage of the 50% No A A A No No 18AH
100
直流制动电流 Inverter rated current.

DC injection Used to set the time to perform

braking time at DC injection braking at start in
start units of 1 second. 0.00
b2-03 Used to stop coasting motor and to 0.00 s No A A A A A 18BH
restart it. When the set value is 0, 10.00
起动制动时间 DC injection braking at start is not
performed.

„Inputting the DC Injection Brake Command from Control Circuit Terminals

If you set a multi-function contact input terminal (H1-††) to 60 (DC injection brake command), you can
apply the DC injection brake to the motor by turning ON the terminal for which the DC injection brake com-
mand has been set when the Inverter is being stopped. DC injection braking is used at startup for flux vector
control.
The time chart for the DC injection brake is shown below.

DC injection brake command

FRUN

Output frequency

DC injection brake b2-01 DC injection brake

E1-09
(DC injection braking at (DC injection braking at
startup is used for flux startup is used for flux
vector control.) vector control.)
If you input the DC injection brake command from an external terminal, or if the Run Com-
mand and jog command are input, the DC injection brake will be disabled, and operation will
resume.

Fig 6.18 DC Injection Brake Time Chart

6-16
 Stopping Methods

„Changing the DC Injection Brake Current Using an Analog Input

If you set H3-09 (Multi-function Analog Input Terminal A2 Function Selection) or H3-05 (Multi-function
Analog Input Terminal A3 Function Selection) to 6 (DC injection brake current), you can change the DC
injection brake current level using the analog input.
At 10 V input (voltage) or 20 mA input (current), 100% of the Inverter rated current will be applied.

DC injection brake voltage level

Inverter rated current

Fig 6.19 DC Injection Brake Current Using an Analog Input

‹ Using an Emergency Stop

Set a multi-function input terminal (H1-††) to 15 or 17 (emergency stop) to decelerate to a stop at the decel-
eration time set in C1-09. If inputting the emergency stop with an NO contact, set the multi-function input ter-
minal (H1-††) to 15, and if inputting the emergency stop with an NC contact, set the multi-function input
terminal (H1-††) to 17.
After the emergency Stop Command has been input, operation cannot be restarted until the Inverter has
stopped. To cancel the emergency stop, turn OFF the Run Command and emergency Stop Command.

„Related Parameters

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Emergency stop The deceleration time when the
time multi-function input “Emergency
0.0 to
(fast) stop” is set to ON.
C1-09 6000.0 10.0 s No A A A A A 208H
This function can be used as a
*
紧急停止时间 stopping method when a fault has
been detected.
* The setting range for acceleration/deceleration times depends on the setting of C1-10 (Acceleration/deceleration Time Setting Unit). If C1-10 is set to 0,
the setting range is 0.00 to 600.00 (s).

6-17
 Acceleration and Deceleration Characteristics
This section explains the acceleration and deceleration characteristics of the Inverter.

‹ Setting Acceleration and Deceleration Times

Acceleration time indicates the time taken for the output frequency to climb from 0% to 100%. Deceleration
time indicates the time taken for the output frequency to reduce to 0%. The factory setting of the acceleration
time is C1-01, and the factory setting of the deceleration time is C1-02.

„Related Parameters

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Acceleration Sets the acceleration time to accel-
C1-01 time 1 erate from 0 to the maximum output Yes Q Q Q Q Q 200H
加速时间 1 frequency, in 1-second units.

Deceleration Sets the deceleration time to decel-

C1-02 time 1 erate from the maximum output fre- Yes Q Q Q Q Q 201H
减速时间 1 quency to 0, in 1-second units.

Acceleration The acceleration time when the

C1-03 time 2 multi-function input “accel/decel Yes A A A A A 202H
加速时间 2 time 1” is set to ON.

Deceleration The deceleration time when the

C1-04 time 2 multi-function input “accel/decel Yes A A A A A 203H
减速时间 2 time 1” is set to ON.
0.0 to
Acceleration 6000.0 10.0 s
The acceleration time when the *
C1-05 time 3 multi-function input “accel/decel No A A A A A 204H
加速时间 3 time 2” is set to ON.

Deceleration The deceleration time when the

C1-06 time 3 multi-function input “accel/decel No A A A A A 205H
减速时间 3 time 2” is set to ON.

Acceleration The acceleration time when the

time 4 multi-function input “accel/decel
C1-07 No A A A A A 206H
time 1” and “accel/decel time 2” are
加速时间 4 set to ON.

Deceleration The deceleration time when the

time 4 multi-function input “accel/decel
C1-08 No A A A A A 207H
time 1” and “accel/decel time 2” are
减速时间 4 set to ON.

Accel/decel
time setting
unit 0: 0.01-second units
C1-10 0 or 1 1 No A A A A A 209H
1: 0.1-second units
加减速时间
单位

6-18
 Acceleration and Deceleration Characteristics

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Accel/decel Sets the frequency for automatic
time switch- acceleration/deceleration switching.
ing frequency Below set frequency: Accel/decel
time 4
0.0 to
C1-11 Above set frequency: Accel/decel 0.0 Hz No A A A A A 20AH
400.0
time 1
切换频率 The multi-function input “accel/
decel time 1” or “accel/decel time
2” take priority.

S-curve char-
acteristic time
at accelera- 0.00 to
C2-01 0.20 s No A A A A A 20BH
tion start 2.50

加速开始 S 字
All sections of the S-curve charac-
S-curve char- teristic time are set in seconds units.
acteristic time When the S-curve characteristic
at accelera- time is set, the accel/decel times 0.00 to
C2-02 0.20 s No A A A A A 20CH
tion end will increase by only half of the S- 2.50
curve characteristic times at start
加速结束 S 字
and end.
S-curve char- Run Command
OFF
acteristic time Output ON
at decelera- frequency 0.00 to
C2-03 C2-02 C2-03 0.20 s No A A A A A 20DH
tion start 2.50
C2-01 C2-04
减速开始 S 字
Time

S-curve char-
acteristic time
at decelera- 0.00 to
C2-04 0.00 s No A A A A A 20EH
tion end 2.50

减速结束 S 字

* The setting range for acceleration/deceleration times depends on the setting of C1-10 (Acceleration/deceleration Time Setting Unit). If C1-10 is set to 0,
the setting range is 0.00 to 600.00 (s).

„Setting Acceleration and Deceleration Time Units

Set the acceleration/deceleration time units using C1-10. Constant C1-10 is set to 1 at the factory.
Set value Details
0 The acceleration/deceleration time settings range is 0.00 to 600.00 in units of 0.01 s.
1 The acceleration/deceleration time settings range is 0.00 to 6000.0 in units of 0.1 s.

„Switching Acceleration and Deceleration Time Using Multi-Function Input Terminal

Commands
Using the Inverter, you can set four acceleration times and four deceleration times. When the multi-function
input terminals (H1-††) are set to 7 (acceleration/deceleration time selection 1) and 1A (acceleration/decel-
eration time selection 2), you can switch the acceleration/deceleration time even during operation by combin-
ing the ON/OFF status of the terminals.
The following table shows the acceleration/deceleration time switching combinations.
Acceleration/Decelera- Acceleration/Decelera-
tion Time Selection 1 Ter- tion Time Selection 2 Ter- Acceleration Time Deceleration Time
minal minal
OFF OFF C1-01 C1-02

6-19
 Acceleration/Decelera- Acceleration/Decelera-
tion Time Selection 1 Ter- tion Time Selection 2 Ter- Acceleration Time Deceleration Time
minal minal
ON OFF C1-03 C1-04
OFF ON C1-05 C1-06
ON ON C1-07 C1-08

„Switching Acceleration and Deceleration Time Automatically

Use this setting when you want to switch acceleration/deceleration time automatically using the set frequency.
When the output frequency reaches the set value in C1-11, the Inverter switches the acceleration/deceleration
time automatically as shown in the following diagram.
Set C1-11 to a value other than 0.0 Hz. If C1-11 is set to 0.0 Hz, the function will be disabled.

Output frequency

Acceleration/
deceleration time
switching frequency
(C1-11)

C1-07 rate C1-01 rate C1-02 rate C1-08 rate

When output frequency ≥ C1-11, acceleration and deceleration are performed using
Acceleration/deceleration Time 1 (C1-01, C1-02).
When output frequency < C1-11, acceleration and deceleration are performed using
Acceleration/deceleration Time 4 (C1-07, C1-08).

Fig 6.20 Acceleration/deceleration Time Switching Frequency

„Adjusting Acceleration and Deceleration Time Using an Analog Input

If you set H3-09 (Multi-function Analog Input Terminal A2 Function Selection) or H3-05 (Multi-function
Analog Input Terminal A3 Function Selection) to 5 (acceleration/deceleration time gain), you can adjust the
acceleration/deceleration time using terminal A2's input voltage.
The Inverter's acceleration time when the acceleration time has been set in C1-01 is as follows:
Acceleration time = C1-01 set value x acceleration/deceleration time gain

Acceleration/deceleration time gain (set value: 5)

(Acceleration/deceleration gain from 1 to

10 V) = 10 V/Input voltage (V) x 10 (%)

Fig 6.21 Acceleration/Deceleration Time Gain Using an Analog Input

6-20
 Acceleration and Deceleration Characteristics

„Entering S-curve Characteristics in the Acceleration and Deceleration Time

By performing acceleration and deceleration using an S-curve pattern, you can reduce shock when starting and
stopping the machine.
Using the Inverter, you can set an S-curve characteristic time for each of the following: Acceleration start
time, deceleration start time, acceleration end time, and deceleration end time.

Set the S-curve characteristic time to lengthen acceleration/deceleration time as follows:

Acceleration time = Selected acceleration time + (Acceleration start time S-curve characteristic time +
Acceleration end time S-curve characteristic time) / 2
Deceleration time = Selected deceleration time + (Deceleration start time S-curve characteristic time +
INFO
Deceleration end time S-curve characteristic time) / 2

Setting Example
The S-curve characteristic when switching operation (forward/reverse) is shown in the following diagram.

Forward

Reverse

C2-02 C2-03 C2-04

Output frequency
C2-01
C2-04
C2-01

C2-02 C2-03

Fig 6.22 S-curve Characteristic during Operation Switching

6-21
 ‹ Accelerating and Decelerating Heavy Loads (Dwell Function)
The dwell function stores the output frequency when starting or stopping heavy loads. By temporarily storing
the output frequency, you can prevent the motor from stalling. When using the dwell function, you must select
a deceleration stop. Set b1-03 (Stopping Method Selection) to 0.

„Related Parameters

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Dwell fre-
quency at
start 0.0 to
b6-01 0.0 Hz No A A A A A 1B6H
400.0
起动暂停频
率
Run command ON
Dwell time OFF
at start Output frequency
0.0 to
b6-02 0.0 s No A A A A A 1B7H
起动暂停时
10.0
间

Dwell fre- b6-01 b6-03 Time

quency at b6-02 b6-04

stop 0.0 to
b6-03 0.0 Hz No A A A A A 1B8H
The dwell function is used to 400.0
停止暂停频 output frequency temporarily
率 when driving a motor with a heavy
Dwell time load.
at stop 0.0 to
b6-04 0.0 s No A A A A A 1B9H
停止暂停时
10.0
间

6-22
 Acceleration and Deceleration Characteristics

‹ Preventing the Motor from Stalling During Acceleration (Stall Prevention

During Acceleration Function)
The Stall Prevention During Acceleration function prevents the motor from stalling if a heavy load is placed
on the motor, or sudden rapid acceleration is performed.
If you set L3-01 to 1 (enabled) and the Inverter output current exceeds the -15% level of the set value in L3-
02, the acceleration rate will begin to slow down. When L3-02 is exceeded, acceleration will stop.
If you set L3-01 to 2 (optimum adjustment), the motor current accelerates to the value set in L3-02. With this
setting, the acceleration time setting is ignored.

„Related Parameters

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Stall preven- 0: Disabled (Acceleration as set.
tion selection With a heavy load, the motor
during accel may stall.)
1: Enabled (Acceleration
stopped when L3-02 level is
exceeded. Acceleration starts
again when the current is
L3-01 0 to 2 1 No A A A No No 48FH
returned.)
加速防止失速选 2: Intelligent acceleration mode
择 (Using the L3-02 level as a
basis, acceleration is
automatically adjusted. Set
acceleration time is
disregarded.)

Stall preven- Effective when L3-01 is set to 1

tion level dur- or 2.
ing accel Set as a percentage of Inverter
0 to
L3-02 rated current. 150% No A A A No No 490H
200
Usually setting is not necessary.
加速防止
失速值 The factory setting reduces the set
values when the motor stalls.
Stall preven- Sets the lower limit for stall pre-
tion limit dur- vention during acceleration, as a
ing accel percentage of the Inverter rated 0 to
L3-03 50% No A A A No No 491H
current, when operation is in the 100
加速防止失速极 frequency range above E1-06.
限 Usually setting is not necessary.

6-23
 „Time Chart
The following figure shows the frequency characteristics when L3-01 is set to 1.

Output current

Stall level during

acceleration

Time
Output frequency

Output frequency is controlled

to prevent the motor stalling.

Time

Fig 6.23 Time Chart for Stall Prevention During Acceleration

„Setting Precautions
• If the motor capacity is small compared to the Inverter capacity, or if the motor is operated using the fac-
tory settings, resulting in the motor stalling, lower the set value of L3-02.
• If using the motor in the constant output range, L3-02 will be automatically lowered to prevent stalling.
L3-03 is the limit value to prevent the stall prevention level in the constant output range from being
reduced more than necessary.
• Set the constants as a percent taking the Inverter rated voltage to be 100%.

Stall prevention level during

acceleration

L3-02 (Stall Prevention Level during Accelera-

tion)

L3-02 x L3-03 (Stall Prevention Limit during Ac-

celeration)

Output frequency
E1-06
Base Frequency (FA)

Fig 6.24 Stall Prevention Level and Limit During Acceleration

6-24
 Acceleration and Deceleration Characteristics

‹ Preventing Overvoltage During Deceleration (Stall Prevention During

Deceleration Function)
The Stall Prevention During Deceleration function makes the rate of deceleration more gentle to suppress
increases in DC bus voltage when the DC bus voltage exceeds the set value during motor deceleration.
This function automatically lengthens the deceleration time with respect to the bus voltage, even if the decel-
eration time has been set to a considerably small value.
If L3-04 is set to 1 or 2, when the main circuit DC voltage approaches the stall prevention level during decel-
eration, deceleration stops, and when deceleration falls below the level, is restarted. Using this operation,
deceleration time is automatically lengthened. If L3-04 is set to 1, deceleration time returns to the set value,
and if L3-04 is set to 2, deceleration is automatically adjusted to a faster deceleration time within the range of
the stall prevention level during deceleration.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Stall preven- 0: Disabled (Deceleration as set.
tion selection If deceleration time is too
during decel short, a main circuit
overvoltage may result.)
1: Enabled (Deceleration is
stopped when the main circuit
voltage exceeds the
overvoltage level.
Deceleration restarts when
voltage is returned.)
2: Intelligent deceleration mode
L3-04 (Deceleration rate is 0 to 3* 1 No Q Q Q Q Q 492H
减速防止失速选
automatically adjusted so that
择 the Inverter can decelerate in
the shortest possible time. Set
deceleration time is
disregarded.)
3: Enabled (with Braking
Resistor Unit)
When a braking option (Braking
Resistor, Braking Resistor Unit,
Braking Unit) is used, always set
to 0 or 3.
* The setting range for flux vector and open-loop vector 2 controls is 0 to 2.

6-25
 „Setting Example
An example of stall prevention during deceleration when L3-04 is set to 1 as shown below.

Output frequency Deceleration time controlled to

prevent overvoltage

Time

Deceleration time
(set value)

Fig 6.25 Stall Prevention During Deceleration Operation

„Setting Precautions
• The stall prevention level during deceleration differs depending on the Inverter capacity. Refer to the fol-
lowing table for details.
Inverter Capacity Stall Prevention Level during Deceleration (V)
200 V Class 380
E1-01 ≥ 400 V 760
400 V Class
E1-01 < 400 V 660
• When using the braking option (braking resistor, Braking Resistor Units, and Braking Units), be sure to set
constant L3-04 to 0 or 3.
• To decelerate at a shorter time than the deceleration time set when L3-04 is set to 0 with the braking option
enabled, set L3-04 to 3.
• The setting of L3-04 is ignored for flux vector control or open-loop vector 2 control.

‹ Preventing Overvoltage by Automatically Reducing the Regenerative

Torque Limit (Overvoltage Inhibit Function)
The overvoltage inhibit function is a function that, by reducing the regenerative torque limit to a value less
than its set value according to the main circuit voltage level, suppresses voltage rises with regenerative torque.
Using this function means that if, for example, the main circuit voltage rises during deceleration, the regener-
ative torque limit will be reduced and so the deceleration rate will be reduced automatically, suppressing rises
in the main circuit voltage.
This function is effective for suppressing overvoltages that occur during stabilization after an overshoot fol-
lowing sudden acceleration. This function differs from the stall prevention during deceleration function in this
respect.
This function is enabled during vector control.

6-26
 Acceleration and Deceleration Characteristics

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Overvoltage 0: Disabled
inhibit selection 1: Enabled
Used to enable or disable the
function for inhibiting main cir-
cuit overvoltages by reducing the
regenerative torque limit accord-
L3-11 ing to the main circuit overvoltage 0 or 1 0 No No No A A A 4C7H
OV 抑制功能 level.
选择 If this function is enabled, when
the main circuit voltage rises,
operation will be performed with
the regenerative torque less than
the set value.

Overvoltage Sets the main circuit voltage level

inhibit voltage for which the regenerative torque
level limit is restricted to 0.
Usually, there is no need to 350 to 380
L3-12 No No No A A A 4C8H
change this setting. If main circuit 390* V*
OV 抑制电压值 overvoltages occur even with the
overvoltage inhibit function
enabled, reduce this setting.
* These values are for a 200 V Class Inverter. For a 400 V Class Inverter, double the values.

„Setting Precautions
When this function is enabled, if the main circuit voltage rises, the regenerative torque limit will decrease to a
value less than its set value and so the motor will not rotate at the speed specified by the speed reference.
Therefore, in applications where it is necessary to rotate the motor at the speed specified by the speed refer-
ence, disable this function and use a converter, a dynamic braking resistor, or a power regenerative unit to sup-
press rises in the main circuit voltage.

6-27
 Adjusting Frequency References
This section explains methods of adjusting frequency references.

‹ Adjusting Analog Frequency References

Gain and bias are among the constants used to adjust analog inputs.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Signal level 0: 0 to 10 V
selection (ter- 1: -10 to 10 V
H3-01 minal A1) 0 or 1 0 No A A A A A 410H
[11-bit + polarity (positive/
端子 A1 信号选择 negative) input]

Gain (terminal Sets the frequency when 10 V is

A1) 0.0 to 100.0
H3-02 input, as a percentage of the maxi- Yes A A A A A 411H
1000.0 %
端子 A1 增益 mum output frequency.

Bias (terminal Sets the frequency when 0 V is -100.0

H3-03 A1) input, as a percentage of the maxi- to 0.0% Yes A A A A A 412H
端子 A1 偏置 mum frequency. +100.0

Signal level 0: 0 to 10 V
selection (ter- 1: -10 to 10 V
H3-04 minal A3) 0 or 1 0 No A A A A A 413H
[11-bit + polarity (positive/
端子 A3 信号电平 negative) input]

Multi-function
analog input
(terminal A3) Select multi-function analog input
H3-05 function selec- 0 to 1F 2 No A A A A A 414H
function for terminal A3.
tion

端子 A3 设定

Gain (terminal Sets the input gain (level) when

A3) 10 V is input. 0.0 to 100.0
H3-06 Yes A A A A A 415H
Set according to the 100% value 1000.0 %
端子 A3 增益 selected from H3-05.
Bias (terminal Sets the input gain (level) when
-100.0
A3) 0 V is input.
H3-07 to 0.0% Yes A A A A A 416H
Set according to the 100% value
端子 A3 偏置 +100.0
selected from H3-05.

Signal level0: 0 to 10 V
selection 1: -10 to 10 V
(terminal A2)
2: 4 to 20 mA (9-bit input).
H3-08 0 to 2 2 No A A A A A 417H
Switch current and voltage input
端子 A2 信号选择 using the switch on the control
panel.

Multi-function
analog input
(terminal A2) Select multi-function analog input
H3-09 function selec- 0 to 1F 0 No A A A A A 418H
function for terminal A2.
tion

端子 A2 设定

6-28
 Adjusting Frequency References

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Gain (terminal Sets the input gain (level) when
A2) 10 V (20 mA) is input. 0.0 to 100.0
H3-10 Yes A A A A A 419H
Set according to the 100% value 1000.0 %
端子 A2 增益 for the function set for H3-09.

Bias (terminal Sets the input gain (level) when 0

-100.0
A2) V (4 mA) is input.
H3-11 to 0.0% Yes A A A A A 41AH
Set according to the 100% value
端子 A2 偏置 +100.0
for the function set for H3-09.

Analog input
filter time con- Sets primary delay filter time con-
stant stant in seconds for the analog 0.00 to 0.03
H3-12 No A A A A A 41BH
input terminal. 2.00 s
模拟量滤波 Effective for noise control etc.
时间

„Adjusting Analog Frequency Reference Using Constants

The frequency reference is input from the control circuit terminals using analog voltage and current.
If using frequency reference terminal A1 as an input terminal, perform adjustments using constants H3-02 and
H3-03. If using multi-function analog input terminal A2 as a frequency reference terminal, perform adjust-
ments using H3-10 and H3-11.
Adjustment can be made using H3-06 and H3-07 when multi-function analog input terminal A3 is used as a
frequency reference terminal.

Frequency reference Frequency reference

(H3-06)

Terminal A1 (A3) Terminal A2 input

(H3-07) input voltage voltage (current)

Terminal A1, A3 input Terminal A2 input

Fig 6.26 Terminals A1 and A2 Inputs

6-29
 „Adjusting Frequency Gain Using an Analog Input
When H3-09 or H3-05 is set to 1 (frequency gain), you can adjust the frequency gain using the analog input
terminal A2 or A3.

Frequency gain

Multi-function analog input

terminal A2 input level

Fig 6.27 Frequency Gain Adjustment (Terminal A2 Input)

The frequency gain for terminal A1 is the product of H3-02 and terminal A2 gain. For example, when H3-02
is set to 100% and terminal A2 is set to 5 V, the terminal A1 frequency reference will be 50%.

Frequency reference

100% H3-02

50% H3-02 0.5

Terminal A1 input voltage

0 10 V

„Adjusting Frequency Bias Using an Analog Input

When constant H3-09 or H3-05 is set to 0 (add to terminal A1), the frequency equivalent to the terminal A2 or
A3 input voltage is added to A1 as a bias.

Frequency bias

Multi-function analog input

terminal A2 or A3 input level

Fig 6.28 Frequency Bias Adjustment (Terminal A2 or A3 Input)

For example, if H3-02 is 100%, H3-03 is 0%, and terminal A2 is set to 1 V, the frequency reference from
terminal A1 when 0 V is input to A1 will be 10%.

6-30
 Adjusting Frequency References

Frequency reference
H3-02

10%
Bias
Terminal A1 input voltage
0V 10 V

When constant H3-09 or H3-05 is set to D (frequency bias 2), the frequency equivalent to the terminal A2 or
A3 input voltage is added to A1 as a bias.

‹ Operation Avoiding Resonance (Jump Frequency Function)

The jump frequency function operates the motor while avoiding resonance caused by characteristic frequen-
cies in the machinery.
This function is effective in creating a frequency reference dead band.
During constant-speed operation, operation within the jump frequency range is prohibited. Smooth operation
still used during acceleration and deceleration, i.e., jumps are not performed.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Jump fre- Set the center values of the jump
d3-01 quency 1 frequencies in Hz. 0.0 Hz No A A A A A 294H
This function is disabled by set-
禁止频率 1
ting the jump frequency to 0 Hz.
Jump fre- Always ensure that the following
quency 2 applies: 0.0 to
d3-02 0.0 Hz No A A A A A 295H
d3-01 ≥ d3-02 ≥ d3-03 400.0
禁止频率 2 Operation in the jump frequency
range is prohibited but during
Jump fre-
acceleration and deceleration,
d3-03 quency 3 0.0 Hz No A A A A A 296H
speed changes smoothly without
禁止频率 3 jump.

Jump fre- Sets the jump frequency band-

quency width width in Hz. 0.0 to
d3-04 1.0 Hz No A A A A A 297H
The jump frequency will be the 20.0
禁止频率幅度 jump frequency ± d3-04.

The relationship between the output frequency and the jump frequency reference is as follows:

6-31
 Output frequency

Frequency reference descending

Jump frequency width d3-04

Frequency
reference
ascending
Jump
frequency
Jump width d3-04
frequency
width d3-04

Jump frequency reference

Jump Jump Jump
frequency frequency frequency
3 (d3-03) 2 (d3-02) 1 (d3-01)

Fig 6.29 Jump Frequency

„Setting Jump Frequency Reference Using an Analog Input

When constant H3-09 (Multi-function Analog Input Terminal A2 Function Selection) or H3-05 (Multi-func-
tion Analog Input Terminal A3 Function Selection) is set to A (jump frequency), you can change the jump fre-
quency using the terminal A2 input level.

Jump frequency

Max. output frequency

E1-04

Multi-function analog input

0V 10 V terminal A2 or A3 input level
(4 mA) (20 mA)

Fig 6.30 Jump Frequency Setting Using an Analog Input

„Setting Precautions
• Set the jump frequency according to the following formula: d3-01 ≥ d3-02 ≥ d3-03 > Analog input.
• When constants d3-01 to d3-03 are set to 0 Hz, the jump frequency function is disabled.

6-32
 Adjusting Frequency References

‹ Adjusting Frequency Reference Using Pulse Train Inputs

The frequency reference can be adjusted when b1-01 (Reference Selection) is set to 4 (Pulse Train Input). Set
the pulse frequency in constant H6-02 to 100% reference, and then adjust the gain and bias accordingly using
H6-03 and H6-04.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Pulse train
input function 0: Frequency reference
H6-01 selection 1: PID feedback value 0 to 2 0 No A A A A A 42CH
2: PID target value
脉冲输入选择

Pulse train 1000

input scaling Set the number of pulses in hertz, 1440
H6-02 to Yes A A A A A 42DH
taking the reference to be 100%. Hz
脉冲输入比例 32000

Pulse train Set the input gain level as a per-

input gain 0.0 to 100.0
H6-03 cent when the pulse train set in Yes A A A A A 42EH
1000.0 %
脉冲输入增益 H6-02 is input.

Pulse train -100.0

input bias Set the input bias when the pulse
H6-04 to 0.0% Yes A A A A A 42FH
train is 0.
脉冲输入偏置 100.0

Pulse train
input filter time Set the pulse train input primary 0.00 to 0.10
H6-05 delay filter time constant in sec- Yes A A A A A 430H
脉冲输入滤波时 onds.
2.00 s
间

The following diagram shows the method for adjusting the frequency reference using pulse inputs.

Gain and bias

Filter =0 Master speed
H6-03
RP frequency
Cycle 1 =1
PID feedback
measurement 1+sT H6-04
Pulse 0 100 PID target value
H6-05 =2
H6-01

Scaling using H6-02

Fig 6.31 Frequency Reference Adjustments Using Pulse Train Inputs

6-33
 Speed Limit (Frequency Reference Limit Func-
tion)
This section explains how to limit the motor speed.

‹ Limiting Maximum Output Frequency

If you do not want the motor to rotate above a given frequency, use constant d2-01.
Set the upper limit value of the Inverter output frequency as a percent, taking E1-04 (Maximum Output Fre-
quency) to be 100%.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Frequency ref-
erence upper Set the output frequency upper
0.0 to 100.0
d2-01 limit limit as a percent, taking the max. No A A A A A 289H
110.0 %
output frequency to be 100%.
频率指令上限

‹ Limiting Minimum Frequency

If you do not want the motor to rotate at below a given frequency, use constants d2-02 or d2-03.
There are two methods of limiting the minimum frequency, as follows:
• Adjust the minimum level for all frequencies.
• Adjust the minimum level for the master speed frequency (i.e., the lower levels of the jog frequency, multi-
step speed frequency, and auxiliary frequency will not be adjusted).

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Frequency ref-
erence lower Sets the output frequency lower
0.0 to
d2-02 limit limit as a percentage of the maxi- 0.0% No A A A A A 28AH
110.0
mum output frequency.
频率指令下限

Master speed Set the master speed reference

reference lower lower limit as a percent, taking 0.0 to
d2-03 limit 0.0% No A A A A A 293H
the max. output frequency to be 110.0
主速指令下限 100%.

6-34
 Speed Limit (Frequency Reference Limit Function)

„Adjusting Frequency Lower Limit Using an Analog Input

If you set constant H3-09 (Multi-function Analog Input Terminal A2 Function Selection) or H3-05 (Multi-
function Analog Input Terminal A3 Function Selection) to 9 (frequency reference lower limit level), you can
adjust the frequency lower level using the terminal A2 input level.

Output frequency lower level

Max. output frequency

E1-04

Multi-function analog input

0V 10 V terminal A2 or A3 input level
(4 mA) (20 mA)

Fig 6.32 Output Frequency Lower Level for Multi-function Analog Input

If constant d2-02 and terminal A2 output frequency lower level have been set at the same time, the larger set
value will become the frequency lower limit.

INFO

6-35
 Improved Operating Efficiency
This section explains functions for improving motor operating efficiency.

‹ Reducing Motor Speed Fluctuation (Slip Compensation Function)

When the load is large, the amount of motor slip also grows large and the motor speed decreases. The slip
compensation function controls the motor at a constant speed, regardless of changes in load. When the motor
is operating at the rated load, constant E2-02 (Motor Rated Slip) × the frequency in constant C3-01 is added to
the output frequency.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Slip compensa- Used to improve speed accuracy
tion gain when operating with a load.
Usually setting is not necessary.
Adjust this constant at the follow-
ing times.
• When actual speed is low, 0.0 to
C3-01 1.0* Yes A No A A No 20FH
increase the set value. 2.5
滑差补偿增益 • When actual speed is high,
decrease the set value.
Used as the applicable control
gain when using flux vector con-
trol.

Slip compensa- Slip compensation primary delay

tion primary time is set in ms units.
delay time Usually setting is not necessary.
Adjust this constant at the follow-
200
ing times. 0 to
C3-02 ms No A No A No No 210H
• Reduce the setting when slip 10000
*
滑差补偿时间 compensation responsive is
slow.
• When speed is not stabilized,
increase the setting.

Slip compensa- Sets the slip compensation limit

tion limit 0 to
C3-03 as a percentage of motor rated 200% No A No A No No 211H
250
滑差补偿极限 slip.

Slip compensa- 0: Disabled.

tion selection 1: Enabled.
during regener- When the slip compensation dur-
ation ing regeneration function has
C3-04 been activated, as regeneration 0 or 1 0 No A No A No No 212H
capacity increases momentarily, it
再生滑差补偿 may be necessary to use a braking
option (braking resistor, Braking
Resistor Unit or Braking Unit.)
Output voltage 0: Disabled.
limit operation 1: Enabled. (The motor flux will
C3-05 selection be lowered automatically 0 or 1 0 No No No A A No 213H
when the output voltage
输出电压限制 become saturated.)
* The factory setting will change when the control method is changed. The open-loop vector 1 factory settings are given.

6-36
 Improved Operating Efficiency

„Adjusting Slip Compensation Gain

You can switch the C3-01 constant settings as shown below by changing the control method.
• V/f control: 0.0
• Open-loop vector control: 1.0
• Flux vector control: 1.0

Set C3-01 to 1.0 to compensate the rated slip set using the rated torque output status.
Adjust the slip compensation gain using the following procedure.
1. Set E2-02 (Motor Rated Slip) and E2-03 (Motor No-load Current) correctly.
You can calculate the motor rated slip from the values on the motor nameplate using the following for-
mula.
Amount of motor rated slip (Hz) = Motor rated frequency (Hz) - No. of rated rotations (min−1.) × No. of
motor poles / 120
Set the values for rated voltage, rated frequency, and no-load current in the motor unladen current. The
motor rated slip is set automatically in the vector control using autotuning.
2. In V/f control, set C3-01 to 1.0. Setting this constant to 0.0 disables slip compensation.
3. Apply a load, and measure the speed to adjust the slip compensation gain. Adjust the slip compensation
gain by 0.1 at a time. If the speed is less than the target value, increase the slip compensation gain, and if
the speed is greater than the target value, reduce the slip compensation gain.
For flux vector control, the slip compensation gain is used as the motor temperature compensation gain. When
the motor temperate increases, the motor’s internal constant increases, resulting in an increase in slip. If C3-01
is set, the amount of slip is adjusted as the temperature rises. Set C3-01 if the amount of torque varies with the
temperature when using torque control or a torque limit. The larger the value of C3-01, the larger the compen-
sation.

„Adjusting Slip Compensation Primary Delay Time Constant

Set the slip compensation primary delay time constant in ms.
You can switch the factory settings as follows by changing the control method.
• V/f control: 2000 ms
• Open-loop vector control: 200 ms
Normally, there is no need to make these settings. When the slip compensation response is low, lower the set
value. When the speed is unstable, increase the set value.

„Adjusting Slip Compensation Limit

In C3-03, set the upper limit for the slip compensation amount as a percent, taking the motor rated slip amount
as 100%.
If the speed is lower than the target value but does not change even when you adjust the slip compensation
gain, the motor may have reached the slip compensation limit. Increase the limit, and check the speed again.
Make the settings, however, to make sure that the value of the slip compensation limit and reference frequency
does not exceed the tolerance of the machine.
The following diagram shows the slip compensation limit for the constant torque range and fixed output range.

6-37
 Slip compensation limit

Output frequency

E1-06: Base frequency

E1-04: Maximum output frequency

Fig 6.33 Slip Compensation Limit

„Selecting Slip Compensation Function During Regeneration

Set whether to enable or disable the slip compensation function during regeneration.
If the slip compensation function operates during regeneration, you might have to use the braking option
(braking resistor, Braking Resistor Unit, and Braking Unit) to momentarily increase the regenerative amount.

„Selecting Output Voltage Limit Operation

If output voltage saturation occurs while the output voltage limit operation is disabled, the output current will
not change, but torque control accuracy will be lost. If torque control accuracy is required, change the settings
to enable the output voltage limit operation.
If the output voltage limit operation is enabled, motor magnetic flux current is controlled automatically, and
torque control accuracy is maintained to limit the output voltage references. Consequently, the output current
will increase by approximately 10% maximum (with rated load) compared with when the output voltage limit
operation is disabled, so check the Inverter current margin.

Setting Precautions
• If using the device at medium to low speed only, if the power supply voltage is 10% or more higher than
the motor rated voltage, or if the torque control accuracy at high speeds is insufficient, it is not necessary to
change the output voltage limit operation.
• If the power supply voltage is too low compared with the motor rated voltage, torque control accuracy may
be lost even if the output voltage limit operation is enabled.

‹ Compensating for Insufficient Torque at Startup and Low-speed Opera-

tion (Torque Compensation)
The torque compensation function detects that the motor load has increased, and increases the output torque.
V/f control calculates and adjusts the motor primary loss voltage according to the output voltage (V), and
compensates for insufficient torque at startup and during low-speed operation. Calculate the compensation
voltage as follows: Motor primary voltage loss × constant C4-01.
Vector control separates the motor excitation current and the torque current by calculating the motor primary
current, and controlling each of the two separately.
Calculate the torque current as follows: Calculated torque reference × C4-01

6-38
 Improved Operating Efficiency

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Torque com- Sets torque compensation gain as
pensation gain a ratio.
Usually setting is not necessary.
Adjust in the following circum-
stances:
• When the cable is long;
increase the set value.
• When the motor capacity is
smaller than the Inverter capac-
ity (Max. applicable motor
capacity), increase the set val- 0.00 to
C4-01 1.00 Yes A A A No No 215H
ues. 2.50
转矩补偿增益 • When the motor is oscillating,
decrease the set values.
Adjust the output current range at
minimum speed rotation so that it
does not exceed the Inverter rated
output current.
Do not alter the torque compensa-
tion gain from its default (1.00)
when using the open-loop vector1
control method.

Torque com- The torque compensation delay

pensation pri- time is set in ms units.
mary delay time Usually setting is not necessary.
constant Adjust in the following circum-
stances: 0 to 20 ms
C4-02 No A A A No No 216H
• When the motor is oscillating, 10000 *

转矩补偿延迟时
increase the set values.
间 • When the responsiveness of the
motor is low, decrease the set
values.
* The factory setting will change when the control method is changed. The open-loop vector 1 factory settings are given.

„Adjusting Torque Compensation Gain

Normally, there is no need to make this adjustment. Do not adjust the torque compensation gain when using
open-loop vector control.
Adjust the torque compensation gain using V/f control in the following circumstances.
• If the cable is very long, increase the set value.
• If the (maximum applicable) motor capacity is smaller than the Inverter capacity, increase the set value.
• If the motor is vibrating, reduce the set value.
Adjust this constant so that the output current during low-speed rotation does not exceed the Inverter rated
output current range.

„Adjusting the Torque Compensation Primary Delay Time Constant

Set the torque compensation function primary delay in ms.
You can switch the factory settings as follows by changing the control method settings:
• V/f control: 200 ms
• V/f control with PG: 200 ms
• Open-loop vector control: 20 ms

6-39
 Normally, there is no need to make this setting. Adjust the constant as shown below.
• If the motor is vibrating, increase the set value.
• If the motor response is low, decrease the set value.

‹ Hunting-prevention Function
The hunting-prevention function suppresses hunting when the motor is operating with a light load. This func-
tion can be used in V/f and V/f with PG.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Hunting-pre- 0: Hunting-prevention function
vention func- disabled
tion selection 1: Hunting-prevention function
enabled
The hunting-prevention function
suppresses hunting when the
motor is operating with a light
N1-01 0 or 1 1 No A A No No No 580H
load.
防止失调功能 This function is enabled in V/f
选择 control method only.
If high response is to be given pri-
ority over vibration suppression,
disable the hunting-prevention
function.

Hunting-pre- Set the hunting-prevention gain

vention gain multiplication factor.
Normally, there is no need to
make this setting.
Make the adjustments as follows:
• If vibration occurs with light 0.00 to
N1-02 1.00 No A A No No No 581H
load, increase the setting. 2.50
防止失调增益 • If the motor stalls, reduce the
setting.
If the setting is too large, the volt-
age will be too suppressed and the
motor may stall.

Hunting-pre-
vention time Set the hunting-prevention pri- 0 to
N1-03 constant mary delay time in units of ms. 500 10 ms* No A A No No No 582H

防止失调时间

* The factory setting depends upon the Inverter capacity. The value for a 200 v Class Inverter of 0.4 kW is given.

6-40
 Improved Operating Efficiency

‹ Stabilizing Speed (Speed Feedback Detection Function)

The speed feedback detection control (AFR) function measures the stability of the speed when a load is sud-
denly applied, by calculating the amount of fluctuation of the torque current feedback value, and compensat-
ing the output frequency with the amount of fluctuation.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Speed feed- Set the internal speed feedback
back detection detection control gain using the
control (AFR) multiplication function.
gain Normally, there is no need to
make this setting.
Adjust this constant as follows:
0.00 to
N2-01 • If hunting occurs, increase the 1.00 No No No A No No 584H
10.00
set value.
AFR 增益 • If response is low, decrease the
set value.
Adjust the setting by 0.05 at a
time, while checking the
response.

Speed feed-
back detection Set the time constant to decide the
control (AFR) 0 to
N2-02 rate of change in the speed feed- 50 ms No No No A No No 585H
time constant 2000
back detection control.
AFR 时间

Speed feed-
back detection Increase the setting if overvoltage
control (AFR) (OV) failures occur at the comple- 0 to 750
N2-03 No No No A No No 586H
time constant 2 tion of acceleration or when the 2000 ms
load changes radically.
AFR 时间 2

6-41
 Machine Protection
This section explains functions for protecting the machine.

‹ Reducing Noise and Leakage Current

The switching frequency of the Inverter’s output transistor can be changed to reduce carrier noise and leakage
current from the motor.

„Related Constants
Name Control Methods
Change Open MEMO
Con- Open
Setting Factory during V/f Flux Loop BUS
stant Description Range Setting Opera- Loop
Number Display V/f with Vec- Vec- Regis-
tion Vector ter
PG tor tor
1
2
Carrier fre-
quency Select carrier wave fixed pattern.
selection 1 to F 6 No
C6-02 Select F to enable detailed settings using No Q Q Q Q 224H
*2 *1 *4
constants C6-03 to C6-07.
载波频率选
择

Carrier Set the carrier frequency upper limit and

frequency lower limit in kHz units. 2.0 to 15.0
C6-03 upper limit The carrier frequency gain is set as fol- 15.0 kHz No A A A A No 225H
*3 lows: *2 *5 *1
载波频率上
With the vector control method, the
限
upper limit of the carrier frequency is
Carrier fixed in C6-03.
frequency 0.4 to 15.0
C6-04 lower limit
Carrier frequency

15.0 kHz No A A No No No 226H

*3
*2 *5 *1
载波频率下
限
Output frequency x (C6-05) x K

Carrier fre- Output

frequency
quency
(Max. output frequency)
propor-
C6-05 tional gain K is a coefficient that depends on the 00 to
00 No A A No No No 227H
*3 setting of C6-03. 99
载波频率比 C6-03 ≥ 10.0 kHz: K = 3
例增益 10.0 kHz > C6-03 ≥ 5.0 kHz: K = 2
5.0 kHz > C6-03: K = 1

Carrier fre-
quency Select the carrier frequency when open-
selection loop vector 2 control is used.
for open- 1: 2 kHz 1 No No No No
C6-11 loop vector 1 to 4 No Q 22DH
2: 4 kHz *1 *4 *4 *4 *4
2 control 3: 6 kHz
无 PG 矢量 2
4: 8 kHz
载波

* 1. The factory settings depend on the capacity of the Inverter. The values for a 200 V Class Inverter for 0.4 kW are given.
* 2. The setting ranges depend on the capacity of the Inverter. The values for a 200 V Class Inverter for 0.4 kW are given.
* 3. This constant can be monitored or set only when F is set for C6-02.
* 4. Displayed in Quick Programming Mode when motor 2 is set for a multi-function input.
* 5. The maximum output frequency depends on the setting for the carrier frequency (refer to page 6-43).

6-42
 Machine Protection

„Control Method and Carrier Frequency Settings

Carrier frequency settings are restricted as listed in the following table according to the control method selec-
tion.
Control Method Carrier Frequency
1: 2.0 kHz
2: 5.0 kHz
3: 8.0 kHz
4: 10.0 kHz
V/f control with or without a PG
5: 12.5 kHz
6: 15.0 kHz
F: Any setting*
Detailed settings are available in C6-03, C6-04, and C6-05.
1: 2.0 kHz
2: 5.0 kHz
3: 8.0 kHz
Open-loop vector 1 control or 4: 10.0 kHz
Flux vector control 5: 12.5 kHz
6: 15.0 kHz
F: Any setting*
The upper limit of the carrier frequency is determined by C6-03.
1: 2.0 kHz
2: 4.0 kHz
Open-loop vector 2 control
3: 6.0 kHz
4: 8.0 kHz

* The upper limit of the carrier frequency depends on the Inverter capacity.

„Carrier Frequency Setting Precautions

When selecting the carrier frequency, observe the following precautions.
• Adjust the carrier frequency according to the cases shown below.
If the wiring distance between Inverter and motor is long: Set the carrier frequency low. (Use the following
values as guidelines.)
Wiring Length 50 m or less 100 m or less Over 100 m
C6-02 (carrier frequency
1 to 6 (15 kHz) 1 to 4 (10 kHz) 1 to 2 (5 kHz)
selection) setting

If speed and torque are inconsistent at low speeds: Set the carrier frequency low.
If leakage current from the Inverter is large: Set the carrier frequency low.
If metallic noise from the motor is large: Set the carrier frequency high.

• When using V/f control or V/f control with PG, you can vary the carrier frequency according to the output
frequency, as shown in the following diagram, by setting C6-03 (Carrier Frequency Upper Limit), C6-04
(Carrier Frequency Lower Limit), and C6-05 (Carrier Frequency Proportional Gain).

6-43
 Carrier Frequency

C6-03

Output frequency × C6-05

C6-04
× K*

Output frequency
* K is the coefficient determined by the set E1-04
value in C6-03. Max. Output Frequency
C6-03 ≥ 10.0 kHz: K=3
10.0 kHz > C6-03 ≥ 5.0 kHz: K=2
5.0 kHz < C6-03: K=1

Fig 6.34

• With vector control, the carrier frequency is fixed to the Carrier Frequency Upper Limit in C6-03 if user-
set or by the carrier frequency set in C6-02.
• To fix the carrier frequency, set C6-03 and C6-04 to the same value, or set C6-05 to 0.
• If the settings are as shown below, OPE11 (Constant setting error) will occur.
If Carrier Frequency Proportional Gain (C6-05) > 6 and C6-03 < C6-04.
• The Inverter overload current level can be reduced by the carrier frequency setting, and an OL2 (Inverter
overload) may be detected even if the overload current is smaller than 150%. The reduction levels of the
Inverter overload current are shown in the following figures.

Overload current reduction level

100%

80%
200 V Class,
22 kW

50%

Carrier frequency
0 10 kHz 15 kHz

Fig 6.35 Reduction Levels for V/f, V/f with PG, Open-loop Vector 1, and Flux Vector Control

6-44
 Machine Protection

Overload current reduction level

100%

87%

200 V Class,
30 to 75 kW

50%

Carrier frequency
0 4 kHz 8 kHz
Fig 6.36 Reduction Levels for Open-loop Vector 2 Control

For 400 V Class Inverters, the following limitations apply to the maximum output frequency that can be set
for the carrier frequency settings.

Carrier Frequency 0.4 kHz 1 kHz 1.5 kHz* 2 kHz 3 kHz 5 kHz 8 kHz
Maximum output frequency setting 33 Hz 83 Hz 120 Hz 166 Hz 250 Hz 400 Hz 400 Hz
Applicable Inverter capacity 40P4 to 40P4 to 40P4 to
40P4 to 4300
CIMR-G7B†††† 4110 4075 4045

* The factory setting for 400V 132kW and 220kW flax vector control (A1-02 = 3) is 1.5 kHz, for software version VSG123032 or later.

6-45
 ‹ Limiting Motor Torque (Torque Limit Function)
The motor torque limit function is enabled with flux vector control and open-loop vector control.
In the open-loop vector control and flux vector control, the user-set value is applied to the torque limit by cal-
culating internally the torque output by the motor. Enable this function if you do not want a torque above a
specified amount to be applied to the load, or if you do not want a regeneration value above a specified
amount to occur.

„Related Constants

Name Control Methods

Change Open MEMO
Con- Open
Setting Factory during V/f Flux Loop BUS
stant Description Range Setting Opera- Loop
Number Display V/f with Vec- Vec- Regis-
tion Vector ter
PG tor tor
1
2
Forward
drive
torque limit 0 to
L7-01 200% No No No A A A 4A7H
300
正转电动转
矩极限

Reverse
Sets the torque limit value as a percent-
drive
age of the motor rated torque. 0 to
L7-02 torque limit 200% No No No A A A 4A8H
Four individual regions can be set. 300
反转电动转
矩极限 Output torque
Positive torque
Forward
regenera- No. of
Regenerative motor
tive torque Reverse state rotations 0 to
L7-03 limit Forward 200% No No No A A A 4A9H
Regenerative
state
300
正转再生转
矩极限 Negative torque

Reverse
regenera-
tive torque 0 to
L7-04 limit 200% No No No A A A 4AAH
300
反转再生转
矩极限

Integral
time set- Set the integral time for the torque limit.
ting for When integral control is set for the
5 to 200
L7-06 torque limit torque limit, reduce this setting to No No No A No No 4ACH
10,000 ms
increase the change in frequency for the
转矩限制时 torque limit.
间

Control
method
selection Select the control method for the torque
for torque limit during acceleration and decelera-
limit during tion.
accelera- 0: Proportional control (integral control
L7-07 0, 1 0 No No No A No No 4C9H
tion and during constant speed)
decelera- 1: Integral control
tion Normally, this constant does not need to
be set.
转矩极限控
制选择

6-46
 Machine Protection

Multi-function Analog Input (H3-05, H3-09)

Control Methods
Set- Open Open
ting Function Contents (100%) V/f Loop Flux Loop
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
10 Positive torque limit Motor's rated torque No No Yes Yes Yes

11 Negative torque limit Motor's rated torque No No Yes Yes Yes

12 Regenerative torque limit Motor's rated torque No No Yes Yes Yes

15 Positive/negative torque limit Motor's rated torque No No Yes Yes Yes

Note The forward torque limit is the limit value when the analog input signal generates forward torque. This torque limit setting is enabled even when the
analog input signal generates forward torque while the motor is operating (regeneration).

„Setting the Torque Limit in Constants

Using L7-01 to L7-04, you can set individually four torque limits in the following directions: Forward drive,
reverse drive, forward regeneration, and reverse regeneration.

„Set the Torque Limit Value Using an Analog Input

You can change the analog input level torque limit value by setting the torque limit in multi-function analog
input terminals A2 and A3.
The analog input terminal signal level is factory-set as follows:
Multi-function analog input terminal A2: 4 to 20 mA
Multi-function analog input terminal A3: 0 to 10
The following diagram shows the relationship between the torque limits.

Output torque

Positive
Positive/negative torque limits
Forward torque limit

Regenerative torque limit

No. of motor rotations
Reverse operation Forward operation

Regenerative torque limit

Negative torque limit
Positive/negative torque limits
Negative

Fig 6.37 Torque Limit by Analog Input

6-47
 „Setting Torque Limits Using Constants and an Analog Input
The following block diagram shows the relationship between torque limit using constants and torque limit
using an analog input.

Multi-function analog input Positive forward drive

Reverse positive regenerative torque
torque
Forward torque limit
Terminal (set value = 10)
A2 or A3 Forward negative regenerative torque
Negative torque limit
(set value = 11) Min: Minimum value priority circuit
Regenerative torque limit
(set value = 12) Reverse
Positive/negative torque limit drive
(set value = 15) reverse
torque
Forward torque limit Forward torque limit
(L7-01)
Reverse torque limit Reverse torque limit
(L7-02)
Constants Forward regenerative torque Forward regenerative
limit (L7-03) torque limit
Reverse regenerative torque Reverse regenerative
limit (L7-04) torque limit
175% of Inverter rated current

Fig 6.38 Torque Limit Using Constants and an Analog Input

„Selecting the Control Method for Torque Limit during Acceleration and Deceleration
L7-07 is used to select the control method for the torque limit during acceleration and deceleration. The selec-
tions are proportional control and integral control. For applications, such as presses, in which the torque limit
will be reached during acceleration and deceleration, torque control can be given priority by selecting integral
control. To increase the change in frequency for the torque limit when integral control is selected, decrease the
value set for L7-06 (Integral Time Setting for Torque Limit).

„Setting Precautions
• When the torque limit function is operating, control and compensation of the motor speed is disabled
because torque control is given priority. Therefore, the acceleration and deceleration times may increase or
the number of motor rotations may decrease.
• When using the torque limit to raise and lower loads, do not carelessly lower the torque limit value, as this
may result in the motor falling or slipping.
• Torque limits using an analog input are the upper limit value (during 10 V or 20 mA input) of 100% of the
motor rated torque. To make the torque limit value during 10 V or 20 mA input 150% of the rated torque,
set the input terminal gain to 150.0 (%). Adjust the gain for multi-function analog input terminal A2 using
H3-10 and for multi-function analog input terminal A3 using H3-06.
• The torque limit accuracy is ±5% at the output frequency of 10 Hz or above. When output frequency is less
than 10 Hz, accuracy is lowered.
• When the torque is limited while L7-07 is set to 1 (integral control), the acceleration and deceleration
times may increase or the motor speed may not agree with the speed reference value.

6-48
 Machine Protection

‹ Preventing Motor Stalling During Operation

Stall prevention during operation prevents the motor from stalling by automatically lowering the Inverter's
output frequency when a transient overload occurs while the motor is operating at a constant speed.
Stall prevention during operation is enabled only during V/f control. If the Inverter output current continues to
exceed the setting in constant L3-06 for 100 ms or longer, the motor speed is reduced. Set whether to enable or
disable deceleration time using constant L3-05. Set the deceleration time using C1-02 (Acceleration time 1) or
C1-04 (Acceleration Time 2).
If the Inverter output current reaches the set value in L3-06 - 2% (Inverter Rated Output Current), the motor
will accelerate again at the frequency set or the acceleration time set.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Stall preven- 0: Disabled (Runs as set. With a
tion selection heavy load, the motor may
during running stall.)
1: Deceleration time 1 (the
L3-05 deceleration time for the stall 0 to 2 1 No A A No No No 493H
运行中防失速选
prevention function is C1-02.)
择 2: Deceleration time 2 (the
deceleration time for the stall
prevention function is C1-04.)

Stall preven- Effective when L3-05 is 1 or 2.

tion level dur- Set as a percentage of the Inverter
ing running rated current. 30 to
L3-06 160% No A A No No No 494H
Usually setting is not necessary. 200
运行中防止失速 The factory setting reduces the set
值 values when the motor stalls.

6-49
 ‹ Changing Stall Prevention Level during Operation Using an Analog Input
If you set H3-09 (Multi-function Analog Input Terminal A2 Function Selection) or H3-05 (Multi-function
Analog Input Terminal A3 Function Selection) to 8 (stall prevention level during run), you can change the stall
level during operation by setting H3-10 (Gain (Terminal A2)) and H3-11 (Bias (Terminal A2)) or H3-06 (Gain
(Terminal A3)) and H3-07 (Bias (Terminal A3).
The stall prevention level during operation enabled is the multi-function analog input terminal A2 or A3 input
level or the set value in constant L3-06, whichever is the smaller.

Stall prevention level during operation

Multi-function analog input

terminal A2, A3 input level

(4 mA) (8.8 mA) (20 mA)

Fig 6.39 Stall Prevention Level during Operation Using an Analog Input

If the motor capacity is smaller than the Inverter capacity or the motor stalls when operating at the factory set-
tings, lower the stall prevention level during operation.

INFO

‹ Using Frequency Detection: L4-01 to L4-05

Set these constants when outputting one of the frequency agree or frequency detection signals from a multi-
function output. When using flux vector control, the motor speed is detected.

„Related Constants
Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Speed agree Set the speed that you want to
detection level detect in Hz.
0.0 to
L4-01 The set speed is an absolute value, 0.0 Hz No A A A A A 499H
400.0
频率检出值 so the speed is detected in forward
or reverse.

Speed agree
detection width Set the speed detection range in 0.0 to
L4-02 2.0 Hz No A A A A A 49AH
Hz. 20.0
频率检出幅度

Speed agree
detection level Set the speed that you want to
−400.0
(+/−) detect in Hz.
L4-03 to 0.0 Hz No A A A A A 49BH
Set positive values for forward,
频率检出值
+400.0
negative values for reverse.
＋－

6-50
 Machine Protection

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Speed agree
detection width
(+/−) Set the speed detection range in 0.0 to
L4-04 2.0 Hz No A A A A A 49CH
Hz. 20.0
频率检出幅度
＋－

„Constants and Output Signals

User Constant Number Name Function
Fref/Set Agree 1
Frequency Detection 1
L4-01 Speed agree detection level
Frequency Detection 2
Frequency Detection 5
Fref/Fout Agree 1
Fref/Set Agree 1
L4-02 Speed agree detection width Frequency Detection 1
Frequency Detection 2
Frequency Detection 5
Fref/Set Agree 2
L4-03 Speed agree detection level (+/-) Frequency Detection 3
Frequency Detection 4
Fref/Fout Agree 2
Fref/Set Agree 2
L4-04 Speed agree detection width (+/-)
Frequency Detection 3
Frequency Detection 4

Set the corresponding setting in the multi-function output (H2-01 to H2-05) to output the desired Fref/Fout
Agree signal, Fref/Set Agree signal, or Frequency Detection signal.
Function Setting
Fref/Fout Agree 1 2
Fref/Set Agree 1 3
Frequency Detection 1 4
Frequency Detection 2 5
Fref/Fout Agree 2 13
Fref/Set Agree 2 14
Frequency Detection 3 15
Frequency Detection 4 16
Frequency Detection 5 36

6-51
 Timing Chart for Frequency Detection Operation
Related L4-01: Speed Agree Level L4-03: Speed Agree Level +/−
constant L4-02: Speed Agree Width L4-04: Speed Agree Width +/−
Fref/Fout Agree 1 Fref/Fout Agree 2

Frequency L4-02 Frequency L4-04

reference reference

Output frequency Output frequency

or motor speed
Fref/Fout or motor speed

Agree
L4-02

Fref/Fout Agree 1 OFF ON Fref/Fout Agree 2 OFF ON

(Multi-function output setting = 2) (Multi-function output setting = 13)

Fref/Set Agree 1 Fref/Set Agree 2 +/−

(ON at the following conditions during frequency (ON at the following conditions during frequency
agree) agree)
L4-02 L4-04

L4-01 L4-03
Fref/Set tput frequency
Output frequency
or motor speed
Agree motor speed

L4-01

L4-02

f/Set Agree 1 OFF ON Fref/Set Agree 2 OFF ON

(Multi-function output setting = 3) (Multi-function output setting = 14)

Frequency (FOUT) Detection 1 Frequency (FOUT) Detection 3

(L4-01 > | Output frequency |) (L4-03 > Output frequency)
L4-02 L4-04

L4-01 L4-03

Output frequency Output frequency

or motor speed or motor speed

L4-01

L4-02

Freq. Detection 1 Freq. Detection 3 ON OFF

ON OFF

(Multi-function output setting = 4) (Multi-function output setting = 15)

Frequency (FOUT) Detection 2 Frequency (FOUT) Detection 4

(L4-01 < | Output frequency |) (L4-01 < Output frequency)
L4-02 L4-04

L4-01 L4-03

Fre- Output frequency Output frequency

or motor speed
quency or motor speed

Detection
L4-01

L4-02

Freq. Detection 2 OFF ON Freq. Detection 4 OFF ON

(Multi-function output setting = 5) (Multi-function output setting = 16)

Frequency (FOUT) Detection 5

(L4-01 < | Output frequency |)
L4-02

L4-01

Output frequency
or motor speed

L4-01

L4-02

Freq. Detection 5 OFF ON

(Multi-function output setting = 36) OFF during baseblock

6-52
 Machine Protection

‹ Detecting Motor Torque

If an excessive load is placed on the machinery (overtorque) or the load is suddenly lightened (undertorque),
you can output an alarm signal to multi-function output terminal M1-M2, P1-PC, P2-PC, P3-C3, or P4-C4.
To use the overtorque/undertorque detection function, set B, 17, 18, 19 (overtorque/undertorque detection NO/
NC) in one of the following constants: H2-01 to H2-05 (multi-function output terminals M1-M2, P1-PC, P2-
PC, P3-C3, and P4-C4 function selection).
The overtorque/undertorque detection level is the current level (Inverter rated output current 100%) in V/f
control, and the motor torque (motor rated torque 100%) in vector control.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Torque detec- 0: Overtorque/undertorque
tion selection 1 detection disabled.
1: Overtorque detection only
with speed agreement;
operation continues after
overtorque (warning).
2: Overtorque detected
continuously during
operation; operation continues
after overtorque (warning).
3: Overtorque detection only
with speed agreement; output
stopped upon detection
(protected operation).
4: Overtorque detected
continuously during
operation; output stopped
upon detection (protected
L6-01 0 to 8 0 No A A A A A 4A1H
operation).
转矩检出 1
动作 5: Undertorque detection only
with speed agreement;
operation continues after
overtorque (warning).
6: Undertorque detected
continuously during
operation; operation continues
after overtorque (warning).
7: Undertorque detection only
with speed agreement; output
stopped upon detection
(protected operation).
8: Undertorque detected
continuously during
operation; output stopped
upon detection (protected
operation).
Torque detec- Open-loop vector control: Motor
tion level 1 rated torque is set as 100%. 0 to
L6-02 150% No A A A A A 4A2H
V/f control: Inverter rated current 300
转矩检出 1 值 is set as 100%.

6-53
 Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Torque detec-
tion time 1 Sets the overtorque/undertorque 0.0 to
L6-03 0.1 s No A A A A A 4A3H
detection time in 1-second units. 10.0
转矩检出 1
时间

Torque detec-
tion selection 2 Multi-function output for over-
L6-04 0 to 8 0 No A A A A A 4A4H
转矩检出 2 torque detection 1 is output to
动作 multi-function contact output
when overtorque detection 1 NO
Torque detec- or overtorque detection 1 NC is
tion level 2 0 to
L6-05 selected. Multi-function output 150% No A A A A A 4A5H
300
转矩检出 2 值 for overtorque detection 2 is out-
put to multi-function contact out-
Torque detec- put when overtorque detection 2
tion time 2 NO or overtorque detection 2 NC 0.0 to
L6-06 is selected. 0.1 s No A A A A A 4A6H
10.0
转矩检出 2
时间

Multi-function Output (H2-01 to H2-05)

Control Methods
Set- Open Open
ting Function V/f Loop Flux Loop
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
Overtorque/undertorque detection 1 NO (NO contact: Overtorque/undertorque detec-
B Yes Yes Yes Yes Yes
tion at ON)

Overtorque/undertorque detection 1 NC (NC Contact: Overtorque/undertorque detec-

17 Yes Yes Yes Yes Yes
tion at OFF)

Overtorque/undertorque detection 2 NO (NO Contact: Overtorque/undertorque detec-

18 Yes Yes Yes Yes Yes
tion at ON)
Overtorque/undertorque detection 2 NC (NC Contact: Overtorque/undertorque detec-
19 Yes Yes Yes Yes Yes
tion at OFF)

6-54
 Machine Protection

„L6-01 and L6-04 Set Values and LCD Indications

The relationship between alarms displayed by the Digital Operator when overtorque or undertorque is
detected, and the set values in L6-01 and L6-04, is shown in the following table.
LCD Indications
Set Overtorque/ Overtorque/
Function
Value Undertorque Undertorque
Detection 1 Detection 2
0 Overtorque/undertorque detection disabled. - -
Overtorque detection only with speed matching; operation continues after
1 OL3 flashes OL4 flashes
overtorque (warning).
Overtorque detected continuously during operation; operation continues
2 OL3 flashes OL4 flashes
after overtorque (warning).
Overtorque detection only with speed matching; output stopped upon detec-
3 OL3 lit OL4 lit
tion (protected operation).
Overtorque detected continuously during operation; output stopped upon
4 OL3 lit OL4 lit
detection (protected operation).
Undertorque detection only with speed matching; operation continues after
5 UL3 flashes UL4 flashes
overtorque (warning).
Undertorque detected continuously during operation; operation continues
6 UL3 flashes UL4 flashes
after overtorque (warning).
Undertorque detection only with speed matching; output stopped upon
7 UL3 lit UL4 lit
detection (protected operation).
Undertorque detected continuously during operation; output stopped upon
8 UL3 lit UL4 lit
detection (protected operation).

„Setting Example
The following diagram shows the time chart for overtorque and undertorque detection.
• Overtorque Detection

Motor current (output torque)

* *
L6-02 or L6-05

Overtorque detection 1 NO L6-03 or L6-03 or

or overtorque detection 2 NO L6-06 L6-06
ON ON

* Overtorque detection disabled band is approximately 10% of the Inverter rated output
current (or motor rated torque).

6-55
 • Undertorque Detection

Motor current (output torque)

*
L6-02 or L6-05

L6-03 L6-03
Undertorque detection 1 NO or or
or Undertorque detection 2 NO L6-06 ON L6-06 ON

* The undertorque detection disabled margin is approximately 10% of the Inverter rated output
current (or motor rated torque)

‹ Changing Overtorque and Undertorque Detection Levels Using an Ana-

log Input
If you set constant H3-09 (Multi-function Analog Input Terminal A2 Function Selection) or H3-05 (Multi-
function Analog Input Terminal A3 Function Selection) to 7 (overtorque/undertorque detection level), you can
change the overtorque/undertorque detection level.
If you change the overtorque/undertorque detection level using the multi-function analog input, only over-
torque/undertorque detection level 1 will be enabled.
The following diagram shows the overtorque/undertorque detection level using an analog input.

Detection level

Multi-function analog input

terminal A2, A3 input level
(4 mA) (20 mA)

Fig 6.40 Overtorque/Undertorque Detection Level Using an Analog Input

Multi-Function Analog Input (H3-05, H3-09)

Control Methods
Set- Open Open
ting Function Contents (100%) V/f Loop Flux Loop
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
Overtorque/undertorque detection Motor rated torque for vector control
7 Yes Yes Yes Yes Yes
level Inverter rated output current for V/f control

6-56
 Machine Protection

‹ Motor Overload Protection

You can protect the motor from overload using the Inverter's built-in electronic thermal overload relay.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Motor rated Sets the motor rated current in 1 A
current units.
These set values will become the
0.32 to
reference values for motor protec- 1.90 A
E2-01 6.40 No Q Q Q Q Q 30EH
tion, torque limits and torque con- *1
*2
电机额定电流 trol.
This constant is automatically set
during autotuning.

Motor 2 rated Sets the motor rated current in 1 A

current units.
These set values will become the 0.32
reference values for motor protec- to 1.90 A
E4-01 No A A A A A 321H
tion, torque limits and torque con- 6.40 *1
电机额定电流 trol. *3
This constant is automatically set
during autotuning.
Motor protec- Sets whether the motor overload
tion selection function is enabled or disabled at
electric thermal overload relay.
0: Disabled
1: General-purpose motor
protection
2: Inverter motor protection
3: Vector motor protection
L1-01 In some applications when the 0 to 3 1 No Q Q Q Q Q 480H
电机保护功能选 Inverter power supply is turned
择 off, the thermal value is reset, so
even if this constant is set to 1,
protection may not be effective.
When several motors are con-
nected to one Inverter, set to 0 and
ensure that each motor is installed
with a protection device.

Motor protec- Sets the electric thermal detection

tion time con- time in seconds units.
stant Usually setting is not necessary.
The factory setting is 150% over-
0.1 to 1.0
L1-02 load for one minute. No A A A A A 481H
5.0 min
When the motor's overload resis-
电机保护时间 tance is known, also set the over-
load resistance protection time for
when the motor is hot started.
* 1. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given.
* 2. The setting range is from 10% to 200% of the Inverter rated output current. The value for a 200 V Class Inverter for 0.4 kW is given.
For the motor no-load current, set E2-03 to a value less than that of E2-01.
* 3. The setting range is from 10% to 200% of the Inverter rated output current. The value for a 200 V Class Inverter for 0.4 kW is given.

6-57
 Multi-Function Outputs (H2-01 to H2-05)

Control Methods
Set- Open Open
ting Function V/f Loop Flux Loop
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
Motor overload (OL1, including OH3) pre-alarm (ON: 90% or more of the detection
1F Yes Yes Yes Yes Yes
level)

„Setting Motor Rated Current

Set the rated current value on the motor nameplate in constants E2-01 (for motor 1) and E4-01 (for motor 2).
This set value is the electronic thermal base current.

„Setting Motor Overload Protection Characteristics

Set the overload protection function in L1-01 according to the applicable motor.
The induction motor's cooling abilities differ according to the speed control range. Consequently, you must
select the electronic thermal protection characteristics to match the applicable motor's tolerance load charac-
teristics.
The following table shows the motor type and tolerance load characteristics.
L1-01 Electronic Thermal
Set Motor Type Tolerance Load Characteristics Cooling Ability Operation (at 100%
Value Motor Load)
Rated rotation speed
= 100% speed
Short time 60 s.

Use this motor for

When operating continu-
operations using a
Torque (%)

ously at 50/60 Hz or less,

commercial power
General-purpose motor overload detection
supply. This motor
1 motor (standard (OL1) is detected. The
construction yields
motor) Continuous
Frame Inverter outputs the error
number best cooling effect
Max. contact, and the motor
speed Frame number Max. speed
when operating at 50/
of 200 of 160 MJ to 160 LJ min.
coasts to a stop.
LJ min. Frame number Max.
speed of 132 MJ
60 Hz.

Rotation speed (%)

Rated rotation speed

Short time 60 = 100% speed
Torque (%)

This motor yields a

Inverter motor cooling effect even
Operates continuously at 6
2 (constant torque) when operating at
to 50/60 Hz.
(1:10) Continuous
Frame number Max.
low speeds (approx.
speed of 200 LJ min.
Frame number Max. speed
6 Hz).
of 160 MJ to 180 LJ
Frame number Max.
speed of 132 MJ

Rotation speed (%)

6-58
 Machine Protection

L1-01 Electronic Thermal

Set Motor Type Tolerance Load Characteristics Cooling Ability Operation (at 100%
Value Motor Load)

Rated rotation speed

Short time 60 s. = 100% speed

Torque (%)
This motor yields a
cooling effect even
Vector motor Operates continuously at
3 Continuous
when operating at
(1:100) 0.6 to 60 Hz.
Frame number
Max. speed of
200 LJ min. extremely low speeds
Frame number Max. speed (approx. 0.6 Hz).
of 160 MJ to 180 LJ
Frame number Max.
speed of 132 MJ

Rotation speed (%)

‹ Setting Motor Protection Operation Time

Set the motor protection operation time in L1-02.
If, after operating the motor continuously at the rated current, a 150% overload is experienced, set the (hot
start) electronic thermal protection operation time. The factory setting is resistance to 150% for 60 seconds.
The following diagram shows an example of the characteristics of the electronic thermal protection operation
time (L1-02 = 1.0 min., operation at 60 Hz, general-purpose motor characteristics, when L1-01 is set to 1)

Operating time (min.)

Cold start

Hot start

Motor current (%)

E2-01 is set to 100%

Fig 6.41 Motor Protection Operation Time

„Setting Precautions
• If multiple motors are connected to one Inverter, set constant L1-01 to 0 (disabled). To protect the motor,
install a thermal relay in the motor power cable, and perform overload protection on each motor.
• With applications where the power supply is often turned ON and OFF, there is a risk that the circuit cannot be pro-
tected even if this constant has been set to 1 (enabled), because the thermal value will be reset.
• To detect overloads in good time, set the set value in constant L1-02 to a low setting.

• When using a general-purpose motor (standard motor), the cooling ability will be lowered by f1/4 (fre-
quency). Consequently, the frequency may cause motor overload protection (OL1) to occur, even below
the rated current. If operating using the rated current at a low frequency, use a special motor.

6-59
 „Setting the Motor Overload Pre-Alarm
If the motor overload protection function is enabled (i.e., L1-01 is set to other than 0) and you set H2-01 to
H2-05 (multi-function output terminals M1-M2, P1-PC, P2-PC, P3-C3, and P4-C4 function selection) to 1F
(motor overload OL1 pre-alarm), the motor overload pre-alarm will be enabled. If the electronic thermal value
reaches minimum 90% of the overload detection level, the output terminal that has been set will be turned ON.

‹ Motor Overheating Protection Using PTC Thermistor Inputs

Perform motor overheating protection using the thermistor temperature resistance characteristics of the PTC
(Positive Temperature Coefficient) built into the windings of each motor phase.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Alarm opera- Set H3-09 to E and select the
tion selection operation when the input motor
during motor temperature (thermistor) input
overheating exceeds the alarm detection level
(1.17 V).
0: Decelerate to stop using the
L1-03 0 to 3 3 No A A A A A 482H
deceleration time in C1-02.
OH3
1: Coast to stop
检出动作 2: Emergency stop using the
deceleration time in C1-09.
3: Continue operation (H3 on the
Operator flashes).

Motor over- Set H3-09 to E and select the

heating opera- operation when the motor temper-
tion selection ature (thermistor) input exceeds
the operation detection level (2.34
V).
L1-04 0 to 2 1 No A A A A A 483H
0: Decelerate to stop using the
OH4 检出动作 deceleration time in C1-02.
1: Coast to stop
2: Emergency stop using the
deceleration time in C1-09.

Motor tempera- Set H3-09 to E and set the pri-

ture input filter mary delay time constant for 0.00 to
L1-05 time constant 0.20 s No A A A A A 484H
motor temperature (thermistor) 10.00
OH4 检出动作 inputs in seconds.

6-60
 Machine Protection

„PTC Thermistor Characteristics

The following diagram shows the characteristics of the PTC thermistor temperature to the resistance value.

Class F Class H
Resistance (ohms) 180°C
150°C

1330

Tr: Temperature threshold value

550

Temperature
Tr

Tr 5 Tr Tr+5

Fig 6.42 PTC Thermistor Temperature-Resistance Value Characteristics

„Operation during Motor Overheating

Set the operation if the motor overheats in constants L1-03 and L1-04. Set the motor temperature input filter
time constant in L1-05. If the motor overheats, the OH3 and OH4 error codes will be displayed on the Digital
Operator.

Error Codes If the Motor Overheats

Error Code Details
OH3 Inverter stops or continues to operate, according to the setting in L1-03.
OH4 Inverter stops according to the setting in L1-04.
By setting H3-09 (Multi-function Analog Input Terminal A2 Function Selection) or H3-05 (Multi-function
Analog Input Terminal A3 Function Selection) to E (Motor temperature input), you can detect alarm OH3 or
OH4 using the PTC temperature-resistance characteristics, and protect the motor. The terminal connections
are shown in the following diagram. Set H3-08
〔Signal level selection (terminal A2)〕(H3-04 when A3 is used)
to 0 (0 to + 10 V).

Inverter
Multi-function Multi-function
contact input contact output

Fault contact
output

Branch resistance
18 kΩ
A2, A3
(0-10 V)

PTC thermistor Multi-function

PHC output

* When using terminal A2, set DIP switch S1-2 to OFF (0 to 10 V).

Fig 6.43 Mutual Connections During Motor Overheating Protection

6-61
 ‹ Limiting Motor Rotation Direction
If you set motor reverse rotation prohibited, a Reverse Run Command will not be accepted even if it is input.
Use this setting for applications in which reverse motor rotation can cause problems (e.g., fans, pumps, etc.)

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Prohibition of
reverse opera- 0: Reverse enabled
b1-04 tion 0 or 1 0 No A A A A A 183H
1: Reverse disabled
反转禁止选择

6-62
 Continuing Operation

Continuing Operation
This section explains functions for continuing or automatically restarting Inverter operation using speed
search even if an error occurs.

‹ Restarting Automatically After Power Is Restored

Even if a temporary power loss occurs, you can perform estimated/current detection speed search using the
speed search function (b3-01) and restart the Inverter automatically after power is restored to continue motor
operation. To restart the Inverter after power has been restored, set L2-01 to 1 or 2. Make settings of L2-01 to
L2-05 and b3-01 for related details of restarting.
• If L2-01 is set to 1:
when power is restored within the time set in L2-02, the Inverter will restart. If the time set in L2-02 is
exceeded, alarm UV1 (main circuit undervoltage) will be detected.
• If L2-01 is set to 2:
when the main power supply is restored while the control power supply (i.e., power supply to the control
panel) is backed up, the Inverter will restart. Consequently, alarm UV1 (main circuit undervoltage) will not
be detected.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Momentary 0: Disabled [main circuit
power loss undervoltage (UV1)
detection detection]
1: Enabled [Restarted when the
power returns within the time
for L2-02. When L2-02 is
exceeded, main circuit
L2-01 undervoltage (UV1) is 0 to 2 0 No A A A A A 485H
瞬时停电动作选
detected.]
择 2: Enabled while CPU is
operating. [Restarts when
power returns during control
operations. Does not detect
main circuit undervoltage
(UV1).]

Momentary
power loss ride- Ridethrough time, when Momen-
thru time 0 to 0.1 s
L2-02 tary Power Loss Selection (L2- No A A A A A 486H
25.5 *1
瞬时停电补偿时
01) is set to 1, in units of seconds.
间

Min. baseblock Sets the Inverter's minimum base-

time block time in units of one second,
when the Inverter is restarted after
power loss ridethrough.
Sets the time to approximately 0.7
0.1 to 0.2 s
L2-03 times the motor secondary circuit No A A A A A 487H
5.0 *1
最小 BB 时间 time constant.
When an overcurrent or overvolt-
age occurs when starting a speed
search or DC injection braking,
increase the set values.

6-63
 Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Voltage recov- Sets the time required to return
ery time the Inverter output voltage to nor-
mal voltage at the completion of a
speed search, in units of one sec- 0.0 to 0.3 s
L2-04 No A A A A A 488H
ond. 5.0 *1
电压恢复时间 Sets the time required to recover
from 0 V to the maximum volt-
age.
Undervoltage Sets the main circuit undervoltage
detection level (UV) detection level (main circuit
DC voltage) in V units.
150 to
Usually setting is not necessary. 190 V
L2-05 210 No A A A A A 489H
Insert an AC reactor in the *2
*2
PUV 检出值 Inverter input side to lower the
main circuit undervoltage detec-
tion level.
Note Attach a Backup Capacitor Unit for Momentary Power Loss if compensation for power interruptions of up to 2.0 seconds is required for 200 V/400 V
Class Inverters with outputs of 0.4 to 7.5 kW.
* 1. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given.
* 2. These values are for a 200 V Class Inverter. For a 400 V Class Inverter, double the values.

„Setting Precautions
• Error output signals are not output during momentary power loss recovery.
• To continue Inverter operation after power has been restored, make settings so that Run Commands from
the control main circuit terminal are stored even while power is suspended.
• If the momentary power loss operation selection is set to 0 (Disabled), when the momentary power loss
exceeds 15 ms during operation, alarm UV1 (main circuit undervoltage) will be detected.

‹ Speed Search
The speed search function finds the actual speed of the motor that is rotating using inertia, and then starts
smoothly from that speed. When restoring power after a temporary power loss, the speed search function
switches connection from the commercial power supply, and then restarts the fan that is rotating using inertia.

Speed search will be performed in the following cases.

• When Momentary power loss detection (L2-01) is set to 1 or 2 (Enabled) and power is restored after
a momentary power loss.
IMPORTANT
• When Number of auto restart attempts (L5-01) is set from 1 to 10 and the auto restart is performed
after a fault.
• Multi-function contact inputs (H1-††) are set to External search command (61, 62, or 64) and the
command is sent.
• Multi-function contact inputs (H1-††) are set to External baseblock (8 or 9) and the release com-
mand is sent.
The selected speed search type in b3-01, speed calculation or current detection, will be performed.

6-64
 Continuing Operation

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Speed search Enables/disables the speed search
selection (cur- function for the Run Command
rent detection and sets the speed search method.
or speed calcu- 0:Disabled, speed calculation
lation) 1: Enabled, speed calculation
2: Disabled, current detection
3: Enabled, current detection

Speed Calculation:
When the search is started, the
motor speed is calculated and
acceleration/deceleration is 2
b3-01 0 to 3 No A A A No A 191H
performed from the calculated *1
speed to the specified frequency
起动速度搜索 (motor direction is also
searched).

Current Detection:
The speed search is started from
the frequency when power was
momentarily lost and the
maximum frequency, and the
speed is detected at the search
current level.
Speed search Sets the speed search operation
operating cur- current as a percentage, taking the
rent (current Inverter rated current as 100%.
0 to 100%
b3-02 detection) Not usually necessary to set. No A No A No A 192H
200 *1
When restarting is not possible
速度搜索电流 with the factory settings, reduce
the value.

Speed search Sets the output frequency deceler-

deceleration ation time during speed search in
time (current 1-second units. 0.1 to
b3-03 2.0 s No A No A No No 193H
detection) Set the time for deceleration from 10.0
the maximum output frequency to
搜索减速时间 the minimum output frequency.

Speed search Sets the magnetic contactor oper-

wait time (cur- ating delay time when there is a
rent detection magnetic contactor on the output
or speed calcu- side of the Inverter. When a speed 0.0 to
b3-05 0.2 s No A A A A A 195H
lation) search is performed after recover- 20.0
ing from a momentary power loss,
搜索延迟时间 the search operation is delayed by
the time set here.
Speed search Operation restarts at a speed
detection com- obtained by multiplying the speed
pensation gain from the speed search by the com-
(speed calcula- pensation gain.
1.00 to
b3-10 tion) Increase this setting if overvolt- 1.10 No A No A No A 19AH
1.20
ages occur when speed search is
搜索速度补偿增
performed after a long baseblock,
益 for example, in searches at star-
tup.

6-65
 Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Proportional Sets the proportional gain (PI con-
gain of the trol) of the speed estimator during
speed estimator speed search taking the setting of
during speed N4-08 to be equivalent to a setting
search of 1.0. 0.1 to
b3-13 1.0% No No No No No A 19DH
Usually, there is no need to 2.0
change this setting. If, however,
速度推定比例增 the load inertia is large and over-
益 voltages occur during the search,
reduce this setting.

Rotation direc-
tion search 0: Disabled (operates with speci-
selection fied rotation direction)
b3-14 0 or 1 1 No A A A No A 19EH
1: Enabled (operates with rota-
旋转方向搜索选 tion direction found by search)
择

Speed search Sets the current level to retry a

retrial current speed search as a percentage, tak- 0 to
b3-17 level 150% No A No A No A 1F0H
ing the Inverter rated current as 200
搜索重试 I 值 100%.

Speed search
retrial detec- Sets the time for detection in a
tion time 0.00 to
b3-18 speed search retrial in units of 0.10 s No A No A No A 1F1H
1.00
速度搜索检出时
seconds.
间

Number of
speed search
retrials Sets the number of times that a
b3-19 0 to 10 0 No A No A No A 1F2H
speed search can be retried.
速度搜索重试次
数

Min. baseblock Sets the Inverter's minimum base-

time block time in units of one second,
when the Inverter is restarted after
power loss ridethrough.
Sets the time to approximately 0.7
0.1 to 0.2 s
L2-03 times the motor secondary circuit No A A A A A 487H
5.0 *2
最小 BB 时间 time constant.
When an overcurrent or overvolt-
age occurs when starting a speed
search or DC injection braking,
increase the set values.
Voltage recov- Sets the time required to return
ery time the Inverter output voltage to nor-
mal voltage at the completion of a
speed search, in units of one sec- 0.0 to 0.3 s
L2-04 No A A A A A 488H
ond. 5.0 *2
电压恢复时间 Sets the time required to recover
from 0 V to the maximum volt-
age.

* 1. The factory setting will change when the control method is changed. The open-loop vector 1 control factory settings are given.
* 2. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given.

6-66
 Continuing Operation

Multi-function Contact Inputs (H1-01 to H1-10)

Control Methods
Set- Open Open
ting Function V/f Loop Flux Loop
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
61 External search command 1 (ON: Speed search from maximum output frequency) Yes No Yes No Yes

62 External search command 2 (ON: Speed search from set frequency) Yes No Yes No Yes

„Setting Precautions
• When both external search commands 1 and 2 are set for the multi-function contact terminals, an OPE03
(invalid multi-function input selection) operation error may occur. Set either external search command 1 or
external search command 2.
• If speed search during startup is selected when using V/f control with PG, the Unit will start from the fre-
quency detected by PG.
• If performing speed search using external search commands, add an external sequence so that the period
when the Run Command and external search command are both ON is at the very least the Minimum
Baseblock Time (L2-03).
• If the Inverter output is equipped with a contact, set the contact operation delay time in the Speed Search
Wait Time (b3-05). The factory setting is 0.2 s. When not using the contact, you can reduce the search time
by making the setting 0.0 s. After waiting for the speed search wait time, the Inverter starts the speed
search.
• Constant b3-02 is a current detection speed search (current detection level for search completion). When
the current falls below the detection level, the speed search is viewed as completed, and the motor acceler-
ates or decelerates to the set frequency. If a motor overload (OL1) or an Inverter overload (OL2) occurs
and the motor cannot restart, lower the set value.
• If an overcurrent (OC) is detected when using speed search after recovery following a power loss, lengthen
the Minimum Baseblock Time (L2-03).
• If a main circuit over voltage (OV) is detected when using a current detection speed search after a momen-
tary power loss, lengthen the Speed search detection time (b3-03).

„Application Precautions for Speed Searches Using Estimated Speed

• When using V/f control with or without a PG, always perform stationary autotuning for only line-to-line
resistance before using speed searches based on estimated speeds.
• When using vector control, always perform rotational or stationary autotuning (not stationary autotuning
for line-to-line resistance only) before using speed searches based on estimated speeds.
• If the cable length between the motor and Inverter is changed after autotuning has been performed, per-
form stationary autotuning for line-to-line resistance only again.

The motor will not operate when stationary autotuning or stationary autotuning for line-to-line
resistance only is performed.
IMPORTANT

6-67
 „Speed Search Selection
Set whether to enable or disable speed search at startup, and set the type of speed search (estimated speed or
current detection) using setting b3-01. To perform speed search when inputting the Run Command, set b3-01
to 1 or 3.

Search Name Estimated Speed (b3-01 = 0 or 1) Current Detection (b3-01 = 2 or 3)

Estimates the motor speed when the search
Starts speed search from the frequency when
starts, and accelerates and decelerates from the
the temporary power loss was detected, or from
Search Method estimated speed to the set frequency. You can
the highest frequency, and performs speed
also search including direction of motor rota-
detection at the current level during the search.
tion.
External speed search command 1:
External search command 1 and external Starts speed search from the maximum output
External Speed Search search command 2 become the same operation, frequency.
Command estimating the motor speed and starting the External speed search command 2:
search from the estimated speed. Starts speed search from the frequency refer-
ence set before the search command.
Cannot be used multi-motor drives, motors two
Application Precau- In control method without PG, the motor may
or more frames smaller than the Inverter capac-
tions accelerate suddenly with light loads.
ity, and high-speed motors (130 Hz min.)

„Estimated Speed Search (b3-01 = 0 or 1)

The time chart for estimated speed searches is shown below.

Search at Startup (b3-01 = 1)

The time chart when speed search at startup or external speed search command of multi-function inputs has
been selected is shown below.

OFF ON
Run Command Set frequency
reference
Start using
speed detected
Output frequency
b3-02

Output current
1.0 s
* Lower limit set using Speed Search Wait Time (b3-05).

Minimum baseblock time (L2-03) × 0.7*

Note: If the stopping method is set to coast to stop, and the Run Command turns ON in a short time,
the operation may be the same as the search in case 2.

Fig 6.44 Speed Search at Startup (Estimated Speed)

6-68
 Continuing Operation

Speed Search after Short Baseblock (during Power Loss Recovery, etc.) (b3-01 = 0)
The time chart when the Inverter operation is restarted after power has been restored is shown below.
• Loss Time Shorter Than the Minimum Baseblock Time (L2-03)

AC power supply ON OFF Set frequency

Start using
reference
speed detected

Output frequency

Output current
10 ms

*1 Baseblock time may be reduced by the output frequency

*2 immediately before the baseblock.
Minimum baseblock time (L2-03) x 0.75*1 *2 After AC power supply recovery, motor waits for the
minimum Speed Search Wait Time (b3-05).

Fig 6.45 Speed Search after Baseblock (When Estimated Speed: Loss Time Is Set in L2-03)

• Loss Time Longer Than the Minimum Baseblock Time (L2-03)

AC power supply ON OFF Start using speed detected

Set frequency
reference
Output frequency

Output current
10 ms

Minimum baseblock time Speed Search Wait Time

(L2-03) (b3-05)

Fig 6.46 Speed Search After Baseblock (Estimated Speed: Loss Time > L2-03)

6-69
 „Current Detection Speed Search (b3-01 = 2 or 3)
The time charts for current detection speed search is shown below.

Speed Search at Startup (b3-01 = 3)

The time chart when speed search at startup or external speed search command is selected is shown below.

OFF ON Deceleration time set in b3-03

Run Command
Maximum output Set frequency
frequency or reference
set frequency
Output frequency
b3-02

Output current
* * Lower limit is set using Speed Search Time (b3-05).
Minimum baseblock time
(L2-03)

Fig 6.47 Speed Search at Startup (Using Current Detection)

Speed Search after Short Baseblock (b3-01 = 2)

The time chart when the Inverter operation is restarted after power has been restored is shown below.
• Loss Time Shorter Than Minimum Baseblock Time

AC power supply ON OFF Output frequency before power loss

Set frequency
Deceleration reference
time set in b3-03
Output frequency
b3-02
speed search operating current

Output current
*1 Baseblock time may be reduced by the output frequency
immediately before baseblock.
Minimum baseblock time (L2-03) *1 *2 After AC power supply recovery, motor waits for the minimum
Speed Search Wait Time (b2-03).
*2

Fig 6.48 Speed Search After Baseblock (Current Detection: Loss Time < L2-03)

• Loss Time Longer Than Minimum Baseblock Time

AC power supply ON OFF Output frequency before power loss

Set frequency
Deceleration speed set in b3-03 reference
Output frequency
b3-02
Speed search operating time

Output current
Speed search wait time (b3-05)

Minimum baseblock time

(L2-03)

Fig 6.49 Speed Search After Baseblock (Current Detection: Loss Time > L2-03)

6-70
 Continuing Operation

‹ Continuing Operation at Constant Speed When Frequency Reference Is

Lost
The frequency reference loss detection function continues operation using 80% speed of the frequency refer-
ence before loss when the frequency reference using a master speed analog input* is reduced 90% or more in
400 ms.
When the error signal during frequency reference loss is output externally, set H2-01 to H2-05 (multi-function
contact output terminal M1-M2, P1-PC, P2-PC, P3-C3, and P4-C4 function selection) to C (frequency refer-
ence lost).
* Frequency references using the following master speed analog inputs are used to detect a frequency loss.
• Analog input using terminal A1
• Analog input using terminal A2 when H3-09 (Multi-function analog input terminal A2 function selection) is set
to 0 (Add to terminal A1).

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Operation when 0: Stop (Operation follows the
frequency refer- frequency reference.)
ence is missing 1: Operation at 80% speed
continues. (At 80% of speed
L4-05 before the frequency reference 0 or 1 0 No A A A A A 49DH
指令丧失动作
was lost)
选择 Frequency reference is lost: Fre-
quency reference dropped over
90% in 400 ms.

6-71
 ‹ Restarting Operation After Transient Fault (Auto Restart Function)
If an Inverter fault occurs during operation, the Inverter will perform self-diagnosis. If no fault is detected, the
Inverter will automatically restart using the speed search function (b3-01). This is called the auto restart func-
tion.
Set the number of auto restarts in constant L5-01. A fault reset is attempted every 5 ms after a fault occurs and
minimum baseblock time has passed. The number of auto restarts is counted when the Inverter attempts a fault
reset and restarts operation. The protection function will operate if a fault continues to occur after auto restart-
ing the number of times set in L5-01.

The auto restart function can be applied to the following faults. If a fault not listed below occurs, the protec-
tion function will operate and the auto restart function will not.
• OC (Overcurrent) • RH (Braking resistor overheated)
• GF (Ground fault) • RR (Braking transistor error)
• PUF (Fuse blown) • OL1 (Motor overload)
• OV (Main circuit overvoltage) • OL2 (Inverter overload)
• UV1 (Main Circuit Undervoltage, Main Circuit Magnetic Contactor Operation • OH1 (Motor overheat)
Failure)*
• PF (Main circuit voltage fault) • OL3 (Overtorque)
• LF (Output phase failure) • OL4 (Overtorque)
* When L2-01 is set to 1 or 2 (continue operation during momentary power loss)

„Auto Restart External Outputs

To output auto restart signals externally, set H2-01 to H2-05 (multi-function contact output terminals M1-M2,
P1-PC, P2-PC, P3-C3, and P4-C4 function selection) to 1E (restart enabled).

„Related Constants
Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Number of auto Sets the number of auto restart
restart attempts attempts.
L5-01 Automatically restarts after a fault 0 to 10 0 No A A A A A 49EH
故障重试次数
and conducts a speed search from
the run frequency.
Auto restart Sets whether a fault contact out-
operation selec- put is activated during fault
tion restart.
L5-02 0: Not output (Fault contact is 0 or 1 0 No A A A A A 49FH
not activated.)
故障重试接点动
作 1: Output (Fault contact is
activated.)

„ Application Precautions
• The number of auto restarts count is reset under the following conditions:
After auto restart, normal operation has continued for 10 minutes.
After the protection operation has been performed, and the fault has been verified, and an fault reset
has been input.
After the power supply is turned OFF, and then ON again.
• Do not use the auto restart function with variable loads.

6-72
 Continuing Operation

‹ Operation Selection After Cooling Fan Fault

Use the constant setting to select the operation of the motor after a cooling fan fault occurs. This function can
be used for times when a motor should not be stopped quickly (with an emergency stop.)
A cooling fan equipped for 200 V Class Inverters of 7.5 kW, 15 kW, and 30 to 110 kW, and 400 V Class
Inverters of 5.5 to 15 kW and 55 to 300 kW.

„Related Constants
Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
OH1 detection 0: Disabled (FAN minor fault
of Inverter’ s detection)
L8-32 cooling fan 0 or 1 1 No A A A A A 4E2H
1: Enabled (OH1 major fault
OH1 检出选择 detection)

The following table describes the operation of the motor and the display of the Digital Operator in accordance
with the settings of the L8-32 if a cooling fan fault occurred.
Setting Multi-function Con-
Fault Digital Operator Motor Operation
Value tact Output
Cooling Fin Overheating OH1 (lit) Coast to a stop Fault
0
Inverter’s Cooling Fan Fault FAN (blink) Continue operation* Minor fault

Cooling Fin Overheating OH (lit) Coast to a stop Fault

1
Inverter’s Cooling Fan Fault OH1 (lit) Coast to a stop Fault
* If L8-32 is set to 0, the motor will continue running even if a cooling fan fault occurred. However, the Inverter rated output current and the
overload capacity will be reduced. The rated output current will be reduced to 80% if the normal rated output current is 100%, and the overload
capacity will be reduced to the values as follows.
When CT is selected: 100% per every 3 minutes, 150% per every 15 seconds
When VT is selected: 100% per every 30 seconds, 120% per every 10 seconds

If L8-32 is set to 0, be sure to set H2-01 to H2-03 multi-function contact outputs to 10 (minor fault) or to 3D
(Inverter’s cooling fan fault.) If a cooling fan fault occurs, stop the Inverter immediately and replace the cool-
ing fan. If the Inverter continues to run while a cooling fan fault occurs, the Inverter’s cooling ability will be
IMPORTANT affected and the Inverter’s internal temperature will increase and shorten the Inverter’s life.
During a cooling fan fault, the cooling fan stops for about 3 seconds every minute (interval operation.)

6-73
 Inverter Protection
This section explains the functions for protecting the Inverter and the braking resistor.

‹ Performing Overheating Protection on Mounted Braking Resistors

Perform overheating protection on Inverter-mounted braking resistors (Model: ERF-150WJ ††).
When overheating in a mounted braking resistor is detected, an alarm RH (Mounted braking resistor overheat-
ing) is displayed on the Digital Operator, and the motor coasts to a stop.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Protect selec-
tion for internal 0: Disabled (no overheating
DB resistor protection)
L8-01 0 or 1 0 No A A A A A 4ADH
(Type ERF) 1: Enabled (overheating
protection)
制动电阻保护

Multi-function Contact Outputs (H2-01 to H2-05)

Control Methods
Set- Open Open
ting Function V/f Loop Flux Loop
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
D Braking resistor fault (ON: Resistor overheat or braking transistor fault) Yes Yes Yes Yes Yes

The most likely causes of RH (Mounted braking resistor overheating) being detected are that the deceleration
time is too short or that the motor regeneration energy is too large. In these cases, lengthen the deceleration
time or replace the Braking Resistor Unit with one with a higher breaking capacity.
INFO

6-74
 Inverter Protection

‹ Reducing Inverter Overheating Pre-Alarm Warning Levels

The Inverter detects the temperature of the cooling fins using the thermistor, and protects the Inverter from
overheating. You can receive Inverter overheating pre-alarms in units of 1°C.
The following overheating pre-alarm warnings are available: Stopping the Inverter as error protection, and
continuing operation, with the alarm OH (Radiation fins overheating) on the Digital Operator flashing.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Overheat pre- Sets the detection temperature for
alarm level the Inverter overheat detection
pre-alarm in °C. 50 to
L8-02 95 °C* No A A A A A 4AEH
The pre-alarm detects when the 130
过热预警检出值 heatsink temperature reaches the
set value.

Operation Sets the operation for when the

selection after Inverter overheat pre-alarm goes
overheat pre- ON.
alarm 0: Decelerate to stop in
deceleration time C1-02.
1: Coast to stop
L8-03 2: Fast stop in fast-stop time C1- 0 to 3 3 No A A A A A 4AFH
09.
过热预警动作 3: Continue operation (Monitor
选择 display only.)
A fault will be given in setting 0
to 2 and a minor fault will be
given in setting 3.
* The factory setting depends upon the Inverter capacity. The value for 200 V Class Inverter of 0.4 kW is given.

6-75
 Input Terminal Functions
This section explains input terminal functions, which set operating methods by switching functions for the
multi-function contact input terminals (S3 to S12).

‹ Temporarily Switching Operation between Digital Operator and Control

Circuit Terminals
You can switch the Inverter Run Command inputs and frequency reference inputs between local (i.e., Digital
Operator) and remote (input method using b1-01 and b1-02).
You can switch between local and remote by turning ON and OFF the terminals if an output from H1-01 to
H1-10 (multi-function contact input terminal S3 to S12 function selection) has been set to 1 (local/remote
selection).
To set the control circuit terminals to remote, set b1-01 and b1-02 to 1 (Control circuit terminals).

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Reference Set the frequency reference input
selection method.
0: Digital Operator
1: Control circuit terminal
b1-01 0 to 4 1 No Q Q Q Q Q 180H
(analog input)
频率指令选择 2: MEMOBUS communications
3: Option board
4: Pulse train input

Operation Set the Run Command input

method selec- method.
tion 0: Digital Operator
b1-02 1: Control circuit terminal 0 to 3 1 No Q Q Q Q Q 181H
(sequence input)
运行指令选择 2: MEMOBUS communications
3: Option board

You can also perform local/remote switching using the LOCAL/REMOTE Key on the Digital Operator. When
the local/remote function has been set in the external terminals, the LOCAL/REMOTE Key function on the
Digital Operator will be disabled.
INFO

6-76
 Input Terminal Functions

‹ Blocking Inverter Outputs (Baseblock Commands)

Set 8 or 9 (Baseblock command NO/NC) in one of the constants H1-01 to H1-10 (multi-function contact input
terminal S3 to S12 function selection) to perform baseblock commands using the terminal's ON/OFF opera-
tion, and prohibit Inverter output using the baseblock commands. At this time, the motor will be coasting and
“BB” will blink on the Digital Operator.
Clear the baseblock command to restart the operating using speed search from frequency references from the
previous baseblock command input.

Multi-function Contact Inputs (H1-01 to H1-10)

Control Methods
Set- Open Open
ting Function V/f Loop Flux Loop
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
8 External baseblock NO (NO contact: Baseblock at ON) Yes Yes Yes Yes Yes
9 External baseblock NC (NC contact: Baseblock at OFF) Yes Yes Yes Yes Yes

„Time Chart
The time chart when using baseblock commands is shown below.

Forward operation/Stop

Input Cleared
Baseblock command

Frequency reference

Search from stored frequency reference

Output frequency

Hold

Fig 6.50 Baseblock Commands

If using baseblock commands with a variable load, do not frequently input baseblock commands during oper-
ation, as this may cause the motor to suddenly start coasting, and may result in the motor falling or slipping.

IMPORTANT

6-77
 ‹ Stopping Acceleration and Deceleration (Acceleration/Deceleration
Ramp Hold)
The acceleration/deceleration ramp hold function stops acceleration and deceleration, stores the output fre-
quency at that point in time, and then continues operation.
Set one of the constants H1-01 to H1-10 (multi-function contact input terminal S3 to S12 function selection)
to A (acceleration/deceleration ramp hold) to stop acceleration and deceleration when the terminal is turned
ON and to store the output frequency at that point in time. Acceleration and deceleration will restart when the
terminal is turned OFF.
If d4-01 is set to 1 and the Acceleration/Deceleration Ramp Hold command is input, the output frequency is
still stored even after the power supply is turned OFF.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Frequency ref- Sets whether or not frequencies
erence hold on hold will be recorded.
function selec- 0: Disabled (when operation is
tion stopped or the power is turned
on again starts at 0.)
1: Enabled (when operation is
d4-01 stopped or the power is turned 0 or 1 0 No A A A A A 298H
on again starts at the previous
频率保持功能 hold frequency.)
This function is available when
the multi-function inputs “accel/
decel Ramp Hold” or “up/down”
commands are set.

„Time Chart
The time chart when using Acceleration/Deceleration Ramp Hold commands is given below.

Power supply

Forward/Stop

Acceleration/Deceleration
Ramp Hold

Frequency reference

Output frequency

Hold Hold

Fig 6.51 Acceleration/Deceleration Ramp Hold

6-78
 Input Terminal Functions

„Application Precautions
• When d4-01 is set to 1, the output frequency on hold is stored even after the power supply is turned OFF. If
performing operations using this frequency after the Inverter has also been turned OFF, input the Run
Command with the Acceleration/Deceleration Ramp Hold turned ON.
• When d4-01 is set to 0 and a Run Command is input while the Acceleration/Deceleration Ramp Hold is
turned ON, the output frequency will be set to zero.
• If you input an Acceleration/Deceleration Ramp Hold command by error when decelerating during posi-
tioning, deceleration may be canceled.

‹ Raising and Lowering Frequency References Using Contact Signals (UP/

DOWN)
The UP and DOWN commands raise and lower Inverter frequency references by turning ON and OFF a multi-
function contact input terminal S3 to S7.
To use this function, set one of the constants H1-01 to H1-10 (multi-function contact input terminal S3 to S12
function selection) to 10 (UP command) and 11 (DOWN command). Be sure to allocate two terminals so that
the UP and DOWN commands can be used as a pair.
The output frequency depends on the acceleration and deceleration time. Be sure to set b1-02 (Run Command
selection) to 1 (Control circuit terminal).

„Related Constants
Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Frequency ref-
erence upper Set the output frequency upper
0.0 to 100.0
d2-01 limit limit as a percent, taking the max. No A A A A A 289H
110.0 %
output frequency to be 100%.
频率指令上限

Frequency ref-
erence lower Sets the output frequency lower
0.0 to
d2-02 limit limit as a percentage of the maxi- 0.0% No A A A A A 28AH
110.0
mum output frequency.
频率指令下限

Master speed Set the master speed reference

reference lower lower limit as a percent, taking 0.0 to
d2-03 limit 0.0% No A A A A A 293H
the max. output frequency to be 110.0
主速指令下限 100%.

„Precautions
When setting and using UP and DOWN commands, observe the following precautions.

Setting Precautions
If multi-function input terminals S3 to S12 are set as follows, operation error OPE03 (Invalid multi-function
input selection) will occur:
• Only either the UP command or DOWN command has been set.
• UP/DOWN commands and Acceleration/Deceleration Ramp Hold have been allocated at the same time.

6-79
 Application Precautions
• Frequency outputs using UP/DOWN commands are limited by the frequency reference upper and lower
limits set in constants d2-01 to d2-03. Here, frequency references from analog frequency reference termi-
nal A1 becomes the frequency reference lower limit. If using a combination of the frequency reference
from terminal A1 and the frequency reference lower limit set in either constant d2-02 or d2-03, the larger
lower limit will become the frequency reference lower limit.
• If inputting the Run Command when using UP/DOWN commands, the output frequency accelerates to the
frequency reference lower limit.
• When using UP/DOWN commands, multi-step operations are disabled.
• When d4-01 (Frequency Reference Hold Function Selection) is set to 1, the frequency reference held using
the UP/DOWN functions is stored even after the power supply is turned OFF. When the power supply is
turned ON and the Run Command is input, the motor accelerates to the frequency reference that has been
stored. To reset (i.e., to 0 Hz) the stored frequency reference, turn ON the UP or DOWN command while
the Run Command is OFF.

„Connection Example and Time Chart

The time chart and settings example when the UP command is allocated to the multi-function contact input
terminal S3, and the DOWN command is allocated to terminal S4, are shown below.
Constant Name Set Value
H1-01 Multi-function input (terminal S3) 10
H1-02 Multi-function input (terminal S4) 11

Inverter

Forward
operation/Stop

Reverse
operation/Stop
Up command

Down command
Sequence
0 to 10 V analog common
signal Frequency
reference lower limit

Fig 6.52 Connection Example when UP/DOWN Commands Are Allocated

6-80
 Input Terminal Functions

Output frequency
Upper limit
Accelerates to
lower limit Same
frequency

Lower limit

Forward operation/stop

UP command
Reference
frequency reset
DOWN command

Frequency
matching signal*

Power supply

* The frequency matching signal turns ON when the motor is not accelerating/
decelerating while the Run Command is ON.

Fig 6.53 UP/DOWN Commands Time Chart

6-81
 ‹ Accelerating and Decelerating Constant Frequencies in the Analog Refer-
ences (+/- Speed)
The +/- speed function increments or decrements the frequency set in analog frequency reference d4-02 (+/-
Speed Limit) using two contact signal inputs.
To use this function, set One of the constants H1-01 to H1-10 (multi-function contact terminal inputs S3 to
S12 function selection) to 1C (Trim Control Increase command) and 1D (Trim Control Decrease command).
Be sure to allocate two terminals so that the Trim Control Increase command and Trim Control Decrease com-
mand can be used as a pair.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
+ - Speed limits Set the frequency to be add to or
subtracted from the analog fre-
quency reference as a percent,
taking the maximum output fre-
0 to
d4-02 quency to be 100%. 10% No A A A A A 299H
+ - 加减速极限 100
Enabled when the increase (+)
speed command or decrease (-)
speed command is set for a multi-
function input.

„Trim Control Increase/Decrease Command and Frequency Reference

The frequency references using Trim Control Increase/Decrease command ON/OFF operations are shown
below.
Set Frequency Set Frequency
Frequency Reference Reference Reference Set Frequency Command
+ d4-02 - d4-02
Trim Control Increase
ON OFF ON OFF
Command Terminal
Trim Control Decrease
OFF ON ON OFF
Command Terminal

„Application Precautions
• Trim Control Increase/Decrease command is enabled when speed reference > 0 and the speed reference is
from an analog input.
• When the analog frequency reference value - d4-02 < 0, the frequency reference is set to 0.
• If only the Trim Control Increase command or Trim Control Decrease command has been set for a multi-
function contact input terminal S3 to S12, operation error OPE03 (invalid multi-function input selected)
will occur.

6-82
 Input Terminal Functions

‹ Hold Analog Frequency Using User-set Timing

When one of H1-01 to H1-10 (multi-function contact input terminal S3 to S12 function selection) is set to 1E
(sample/hold analog frequency command), the analog frequency reference will be held from 100 ms after the
terminal is turned ON, and operation will continue thereafter at that frequency.

The analog value 100 ms after the command is turned ON is used as the frequency reference.

Sample/hold
command

Analog input

Frequency reference

Fig 6.54 Sample/Hold Analog Frequency

„Precautions
When setting and executing sample and hold for analog frequency references, observe the following precau-
tions.

Setting Precautions
When using sample/hold of analog frequency reference, you cannot use the following commands at the same
time. If these commands are used at the same time, operation error OPE03 (invalid multi-function input selec-
tion) will occur.
• Acceleration/Deceleration Ramp Hold command
• UP/DOWN command
• Trim Control Increase/Decrease command

Application Precautions
• When performing sample/hold of analog frequency references, be sure to store references of 100 ms mini-
mum. If the reference time is less than 100 ms, the frequency reference will not be held.
• The analog frequency reference that is held will be deleted when the power supply is turned OFF.

‹ Switching Operations between a Communications Option Board and

Control Circuit Terminals
You can switch reference input between the Communications Option Board and the control circuit terminals.
Set one of the constants H1-01 to H1-10 (multi-function contact input terminal S3 to S12 function selection)
to 2 (Option/Inverter selection) to enable switching reference input using the terminal ON/OFF status when
the Inverter is stopped.

6-83
 „Setting Precautions
To switch command inputs between the Communications Option Board and the control circuit terminals, set
the following constants.
• Set b1-01 (Reference Selection) to 1 [Control circuit terminal (analog input)]
• Set b1-02 (Operation Method Selection to 1 [Control circuit terminal (sequence inputs)]
• Set one of the constants H1-01 to H1-10 (multi-function contact input terminal S3 to S12 function selec-
tion) to 2 (Option/Inverter selection).
Terminal Status Frequency Reference and Run Command Selection
Inverter
OFF (Can be operated from frequency reference or control circuit terminal from analog input termi-
nal.)
Communications Option Board
ON
(Frequency reference and Run Command are enabled from Communications Option Board.)

‹ Jog Frequency Operation without Forward and Reverse Commands

(FJOG/RJOG)
The FJOG/RJOG command functions operate the Inverter using jog frequencies by using the terminal ON/
OFF operation. When using the FJOG/RJOG commands, there is no need to input the Run Command.
To use this function, set one of the constants H1-01 to H1-10 (multi-function contact input terminal S3 to S12
function selection) to 12 (FJOG command) or 13 (RJOG command).

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Jog frequency The frequency reference when the
0 to
reference jog frequency reference selec- 6.00
d1-17 400.00 Yes Q Q Q Q Q 292H
tion, FJOG command, or RJOG Hz
点动频率上限 *
command is ON.
Note The unit is set in o1-03 (Frequency units of reference setting and monitor). The default for o1-03 is 0 (increments of 0.01 Hz).
* The setting range for open-loop vector 2 control is 0 to 132.0.

Multi-Function Contact Inputs (H1-01 to H1-10)

Control Methods
Set- Open Open
ting Function V/f Loop Flux Loop
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
12 FJOG command (ON: Forward run at jog frequency d1-17) Yes Yes Yes Yes Yes

13 RJOG command (ON: Reverse run at jog frequency d1-17) Yes Yes Yes Yes Yes

„Application Precautions
• Jog frequencies using FJOG and RJOG commands are given priority over other frequency references.
• When both FJOG command and RJOG commands are ON for 500 ms or longer at the same time, the
Inverter stops according to the setting in b1-03 (stopping method selection).

6-84
 Input Terminal Functions

‹ Stopping the Inverter by Notifying Programming Device Errors to the

Inverter (External Fault Function)
The external fault function performs the error contact output, and stops the Inverter operation if the Inverter
peripheral devices break down or an error occurs. The digital operator will display EFx (External fault [input
terminal Sx]). The x in EFx shows the terminal number of the terminal that input the external fault signal. For
example, if an external fault signal is input to terminal S3, EF3 will be displayed.
To use the external fault function, set one of the values 20 to 2F in one of the constants H1-01 to H1-10 (multi-
function contact input terminal S3 to S12 function selection).
Select the value to be set in H1-01 to H1-10 from a combination of any of the following three conditions.
• Signal input level from peripheral devices
• External fault detection method
• Operation during external fault detection
The following table shows the relationship between the combinations of conditions and the set value in H1-
††.
Input Level Error Detection Method
Operation During Error Detection
(See Note 1.) (See Note 2.)
Set
Detection Deceler- Coast to Emer- Continue
Value NO Con- NC Con- Constant
During ate to Stop Stop gency Stop Operation
tact tact Detection
Operation (Error) (Error) (Error) (Warning)
20 Yes Yes Yes
21 Yes Yes Yes
22 Yes Yes Yes
23 Yes Yes Yes
24 Yes Yes Yes
25 Yes Yes Yes
26 Yes Yes Yes
27 Yes Yes Yes
28 Yes Yes Yes
29 Yes Yes Yes
2A Yes Yes Yes
2B Yes Yes Yes
2C Yes Yes Yes
2D Yes Yes Yes
2E Yes Yes Yes
2F Yes Yes Yes
Note 1. Set the input level to detect errors using either signal ON or signal OFF. (NO contact: External fault when ON; NC contact: External fault when
OFF).
2. Set the detection method to detect errors using either constant detection or detection during operation.
Constant detection: Detects while power is supplied to the Inverter.
Detection during operation: Detects only during Inverter operation.

6-85
 Output Terminal Functions
The output terminal function, which sets the output methods by switching the functions of the multi-func-
tion output terminals (M1-M2, P1-PC, P2-PC, P3-C3, and P4-C4), is described here.

During Run (Setting: 0)

OFF The Run Command is OFF and there is not output voltage.
ON The Run Command is ON or a voltage is being output.

During Run 2 (Setting: 37)

The Inverter is not outputting a frequency. (Baseblock, DC injection braking, initial excitation, or
OFF
stopped)
ON The Inverter is outputting a frequency.

• These outputs can be used to indicate the Inverter's operating status.

Run Command OFF ON

Baseblock command OFF ON

Output frequency

During run 1 output OFF ON

OFF ON
During run 2 output

Fig 6.55 Timing Chart for “During RUN” Output

Zero-speed (Setting: 1)
The output frequency is greater than the minimum output frequency (E1-09).
OFF
(With flux vector control, is greater than the zero-speed level (b2-01).)
The output frequency is less than the minimum output frequency (E1-09).
ON
(With flux vector control, is less than the zero-speed level (b2-01).)

Minimum output frequency (E1-09)

(Zero speed level (b2-01) when flux vector control is
Output frequency
being used.)

OFF ON
Zero-speed output

Fig 6.56 Timing Chart for Zero-speed

6-86
 Output Terminal Functions

Motor Overload (OL1) Pre-alarm (Setting: 1F)

OFF The motor protection function's electronic thermal value is less than 90% of the detection level.
ON The motor protection function's electronic thermal value is greater than 90% of the detection level.

• This output function is valid when the motor overload protection function is enabled (L1-01 =1).
• This output can be used to warn of overheating before the protection function itself operates.

Inverter Overheat (OH) Pre-alarm (Setting: 20)

OFF The cooling fin temperature is less than the "OH Pre-Alarm Level" set in L8-02.
ON The cooling fin temperature exceeds the "OH Pre-Alarm Level" set in L8-02.

• This output function indicates that the temperature of the cooling fins reaches the temperature set in L8-02
(the Inverter overheating alarm detection level).

Speed reference limit (Setting: 31)

OFF Other than ON condition
Enables the speed reference limit in the following conditions (During flux vector control method):
1. Frequency reference ≥ Frequency reference upper limit (d2-01)
Frequency reference ≤ Frequency reference lower limit (d2-02)
ON Frequency reference ≥ Output frequency lower limit of the multi-function analog input
(Setting: 9)
2. The frequency reference is less than the Min. output frequency (E1-09), and b1-05 is set to 1,
2, or 3.

Zero-servo End (Setting: 33)

OFF The zero-servo command isn't being input or zero-servo position control hasn't been completed.
The position has been brought within the zero-servo completion width (b9-02) after the zero-servo
ON
command was input.

• This output function indicates that zero-servo position control has been completed.
• The output is turned ON after the zero-servo command is input and the difference between the zero-servo
operation starting position and the current position is within the zero-servo completion width (b9-02).

6-87
 Monitor Constants
This section explains the analog monitor and pulse monitor constants.

‹ Using the Analog Monitor Constants

This section explains the analog monitor constants.

„Related Constants
Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Monitor selec- Sets the number of the monitor
tion (terminal item to be output (U1-††) from
FM) terminal FM.
H4-01 1 to 45 2 No A A A A A 41DH
4, 10 to 14, 25, 28, 34, 39, 40 can-
端子 FM 设定 not be set. 29 to 31 and 41 are not
used.

Gain (terminal Sets the multi-function analog

FM) output 1 voltage level gain.
Sets whether the monitor item
output will be output in multiples 0.00 to
H4-02 1.00 Yes Q Q Q Q Q 41EH
of 10 V. 2.50
端子 FM 增益 The maximum output from the
terminal is 10 V. A meter calibra-
tion function is available.
Bias (terminal Sets the multi-function analog
FM) output 1 voltage level bias.
Sets output characteristic up/
-10.0
down parallel movement as a per-
H4-03 to 0.0% Yes A A A A A 41FH
centage of 10 V.
端子 FM 偏置 +10.0
The maximum output from the
terminal is 10 V. A meter calibra-
tion function is available.

Monitor selec- Sets the number of the monitor

tion (terminal item to be output (U1-††) from
AM) terminal AM.
H4-04 1 to 45 3 No A A A A A 420H
4, 10 to 14, 25, 28, 34, 39, 40 can-
端子 AM 设定 not be set. 29 to 31 and 41 are not
used.

Gain (terminal Set the voltage level gain for

AM) multi-function analog output 2.
Set the number of multiples of 10
V to be output as the 100% output 0.00 to
H4-05 0.50 Yes Q Q Q Q Q 421H
for the monitor items. The maxi- 2.50
端子 AM 增益 mum output from the terminal is
10 V. A meter calibration function
is available.

Bias (terminal Sets the multi-function analog

AM) output 2 voltage level bias.
Sets output characteristic up/
-10.0
down parallel movement as a per-
H4-06 to 0.0% Yes A A A A A 422H
centage of 10 V.
端子 AM 偏置 +10.0
The maximum output from the
terminal is 10 V. A meter calibra-
tion function is available.
Analog output 1 Sets the signal output level for
signal level multi-function output 1 (terminal
H4-07 selection FM) 0 or 1 0 No A A A A A 423H
0: 0 to +10 V output
AO1 信号电平 1: -10 to 10 V output

6-88
 Monitor Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Channel 1 mon- Effective when the Analog Moni-
F4-01 itor selection tor Board is used. 1 to 50 2 No A A A A A 391H
Monitor selection:
CH1 输出监视
Set the number of the monitor
Channel 1 gain item to be output. (U1-††) 0.00 to
F4-02 Gain: 1.00 Yes A A A A A 392H
CH1 输出增益 2.50
Set the multiple of 10 V for out-
putting monitor items.
Channel 2 mon-
4, 10 to 14, 25, 28, 34, 39, 40 can-
F4-03 itor selection 1 to 50 3 No A A A A A 393H
not be set. 29 to 31 and 41 are not
CH2 输出监视 used. When the AO-12 Analog
Monitor Board is used, outputs of
Channel 2 gain ± 10 V are possible. To output ±
10 V, set F4-07 or F4-08 to 1.
When the AO-08 Analog Monitor 0.00 to
F4-04 Board is used, only outputs of 0 to 0.50 Yes A A A A A 394H
CH2 输出增益 2.50
+10 V are possible.
A meter calibration function is
available.

Channel 1 out-
put monitor Sets the channel 1 item bias to
-10.0
F4-05 bias 100%/10 V when the Analog 0.0 Yes A A A A A 395H
to 10.0
Monitor Board is used.
AO CH1 偏置

Channel 2 out-
put monitor Sets the channel 2 item bias to
-10.0
F4-06 bias 100%/10 V when the Analog 0.0 Yes A A A A A 396H
to 10.0
Monitor Board is used.
AO CH2 偏置

Analog output
signal level for 0: 0 to 10 V
F4-07 channel 1 0 or 1 0 No A A A A A 397H
1: -10 to +10 V
CH1 信号电平

Analog output
signal level for 0: 0 to 10 V
F4-08 channel 2 0 or 1 0 No A A A A A 398H
1: -10 to +10 V
CH2 信号电平

„Selecting Analog Monitor Items

The digital operator monitor items (U1-†† [status monitor]) are output from multi-function analog output
terminals FM-AC and AM-AC. Refer to Chapter 5 User Constants, and set the values for the †† part of U1-
†† (status monitor).
Alternatively, you can output monitor items (U1-†† [status monitor]) from analog output option terminal
channels 1 and 2 on analog monitor boards AO-08 and AO-12. Refer to the table of constants, and set the val-
ues.

„Adjusting the Analog Monitor Items

Adjust the output voltage for multi-function analog output terminals FM-AC and AM-AC using the gain and
bias in H4-02, H4-03, H4-05, and H4-06. Also, adjust the output voltage for output channels 1 and 2 of Ana-
log Output option boards AO-08 and AO-12 using the gain and bias in F4-02, F4-04, F4-05, and F4-06.

6-89
 Adjusting the Meter
The output voltage for terminals FM-AC and AM-AC and output channels 1 and 2 of the AO option board can
be adjusted while the Inverter is stopped. For example, just pressing the Enter Key and displaying the data set-
ting display for H4-02 or H4-03 will cause the following voltage to be output by the FM-AC terminals.
10 V/100% monitor output × output gain (H4-02) + output bias (H4-03)
Just pressing the Enter Key and displaying the data setting display for F4-02 or F4-05 will cause the following
voltage to be output to channel 1 of the AO option board.
10 V/100% monitor output × output gain (H4-02) + output bias (H4-05)
Output voltage

Gain x 10 V

Bias x 10/100 V

Monitor item

Fig 6.57 Monitor Output Adjustment

„Switching Analog Monitor Signal Levels

Monitor items corresponding to -10 to 10 V output 0 to 10 V signals when the monitor value is positive (+),
and 0 to -10 V signals when the monitor value is negative (-). For monitor items corresponding to -10 to 10 V,
refer to Chapter 5 User Constants.

You can select the signal levels separately for multi-function analog output terminals and analog output option
terminals.

INFO

‹ Using Pulse Train Monitor Contents

This section explains pulse monitor constants.

„Related Constants
Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Pulse train Select the pulse train monitor out-
monitor selec- put items (value of the †† part 1, 2, 5,
tion of U1-††).
H6-06 20, 24, 2 Yes A A A A A 431H
There are two types of monitor
items: Speed-related items and 36
脉冲监视选择
PID-related items.

Pulse train Set the number of pulses output

monitor scaling when speed is 100% in hertz.
Set H6-06 to 2, and H6-07 to 0, to 0 to 1440
H6-07 Yes A A A A A 432H
make the pulse train monitor out- 32000 Hz
脉冲监视比例 put synchronously to the output
frequency.

6-90
 Monitor Constants

„Selecting Pulse Monitor Items

Output digital operator monitor items (U1-†† [status monitor]) from pulse monitor terminal MP-AC. Refer
to Chapter 5 User Constants, and set the †† part of U1-†† (Status monitor). The possible monitor selec-
tions are limited as follows: U1-01, 02, 05, 20, 24, 36.

„Adjusting the Pulse Monitor Items

Adjust the pulse frequency output from pulse monitor terminal MP-AC. Set the pulse frequency output when
100% frequency is output to H6-07.
Set H6-06 to 2, and H6-07 to 0, to output the frequency synchronous with the Inverter's U-phase output.

„Application Precautions
When using a pulse monitor constant, connect a peripheral device according to the following load conditions.
If the load conditions are different, there is a risk of characteristic insufficiency or damage to the machinery.

Using a Sourcing Output

Load impedance
Output Voltage MP
(Isolated) Load Impedance (kΩ)
VRL (V)
VRL
+5 V min. 1.5 kΩ min. AC
+8 V min. 3.5 kΩ min.
+10 V min. 10 kΩ min.

External power supply

Using a Sinking Input
External Power 12 VDC±10%, Load impedance
Supply (V) 15 VDC±10% MP
Sink Current (mA) 16 mA Max Sinking current

AC

6-91
 Individual Functions
This section explains the individual functions used in special applications.

‹ Using MEMOBUS Communications

You can perform serial communications with MEMOCON-series Programmable Controllers (PLCs) or simi-
lar devices using the MEMOBUS protocol.

„MEMOBUS Communications Configuration

MEMOBUS communications are configured using 1 master (PLC) and a maximum of 31 slaves. Serial com-
munications between master and slave are normally started by the master, and the slave responds.
The master performs signal communications with one slave at a time. Consequently, you must set the address
of each slave beforehand, so the master can perform signal communications using that address. Slaves receiv-
ing commands from the master perform the specified function, and send a response to the master.

MEMOCON-series PLC

Inverter Inverter Inverter

RS-485 connections
example

Fig 6.58 Example of Connections between PLC and Inverter

„Communications Specifications
The MEMOBUS communications specifications are shown in the following table.
Item Specifications
Interface RS-422, RS-485
Communications Cycle Asynchronous (Start-stop synchronization)
Baud rate: Select from 1,200, 2,400, 4,800, 9,600, and 19,200 bps.
Data length: 8 bits fixed
Communications Parameters
Parity: Select from even, odd, or none.
Stop bits: 1 bit fixed
Communications Protocol MEMOBUS (RTU mode only)
Number of Connectable Units 31 units max. (when using RS-485)

6-92
 Individual Functions

„Communications Connection Terminal

MEMOBUS communications use the following terminals: S+, S-, R+, and R-. Set the terminating resistance
by turning ON pin 1 of switch S1 for the last Inverter only, as seen from the PLC.

S+ +
-
S- S1 Terminating
O OFF ON resistance
RS-422A 1
or RS-485 R+ F
F 2
Switch
R- 1

Terminating resistance (1/2 W, 110 Ohms)

Fig 6.59 Communications Connection Terminal

1. Separate the communication cables from the main circuit cables and other wiring and power cables.
2. Use shielded cables for the communication cables, connect the shield cover to the Inverter earth terminal,
and arrange the terminals so that the other end is not connected to prevent operating errors due to noise.
IMPORTANT 3. When using RS-485 communications, connect S+ to R+, and S- to R-, on the Inverter exterior.

R+ R S+ S

„Procedure for Communicating with the PLC

Use the following procedure to perform communications with the PLC.
1. Turn OFF the power supply turned and connect the communication cable between the PLC and the
Inverter.
2. Turn ON the power supply.
3. Set the required communications constants (H5-01 to H5-07) using the Digital Operator.
4. Turn OFF the power supply, and check that the Digital Operator display has completely disappeared.
5. Turn ON the power supply once again.
6. Perform communications with the PLC.

Set the timer on the master to monitor response time from the slave. Set the master so that if the slave does
not respond to the master within the set time, the same command message will be sent from the master
again.
INFO

6-93
 „Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Reference Set the frequency reference input
selection method.
0: Digital Operator
1: Control circuit terminal
b1-01 0 to 4 1 No Q Q Q Q Q 180H
(analog input)
频率指令选择 2: MEMOBUS communications
3: Option board
4: Pulse train input

Operation Set the Run Command input

method selec- method.
tion 0: Digital Operator
b1-02 1: Control circuit terminal 0 to 3 1 No Q Q Q Q Q 181H
(sequence input)
运行指令选择 e 2: MEMOBUS communications
3: Option board
Slave address 0 to 20
H5-01 Set the Inverter's slave address. 1F No A A A A A 425H
*
从站地址

Communica- Set the baud rate for MEMO-

tion speed BUS communications of com-
selection munications connection
terminals.
H5-02 0: 1200 bps 0 to 4 3 No A A A A A 426H
1: 2400 bps
通信速度选择
2: 4800 bps
3: 9600 bps
4: 19200 bps

Communica- Set the parity for MEMO-

tion parity BUS communications of com-
selection munications connection
H5-03 terminals. 0 to 2 0 No A A A A A 427H
0: No parity
通信校验选择
1: Even parity
2: Odd parity

Stopping Set the stopping method for com-

method after munications errors.
communication 0: Deceleration to stop using
error deceleration time in C1-02
H5-04 0 to 3 3 No A A A A A 428H
1: Coast to stop
通信错误检出错
2: Emergency stop using
误 deceleration time in C1-09
3: Continue operation

Communica- Set whether or not a communica-

tion error detec- tions timeout is to be detected as a
H5-05 tion selection communications error. 0 or 1 1 No A A A A A 429H
通信错误检出选
0: Do not detect.
择 1: Detect

Send wait time Set the time from the Inverter

H5-06 receiving data to when the 5 to 65 5 ms No A A A A A 42AH
通信等待时间 Inverter starts to send.

RTS control Select to enable or disable RTS

ON/OFF control.
H5-07 0: Disabled (RTS is always ON) 0 or 1 1 No A A A A A 42BH
RTS 控制选择 1: Enabled (RTS turns ON only
when sending)

6-94
 Individual Functions

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Unit Selection Selects the units used for MEMO-
H5-10 for MEMOBUS BUS registry 0025H (monitors
Register 0025H the output voltage reference). 0 or 1 0 No A A A A A 436H
0: 0.1 V units
MEM25H 单位 1: 1 V units

* Set H5-01 to 0 to disable Inverter responses to MEMOBUS communications.

MEMOBUS communications can perform the following operations regardless of the settings in b1-01 and b1-
02.
• Monitoring operation status from the PLC
• Setting and reading constants
• Resetting errors
• Inputting multi-function commands
An OR operation is performed between the multi-function commands input from the PLC and commands
input from multi-function contact input terminals S3 to S12.

„Message Format
In MEMOBUS communications, the master sends commands to the slave, and the slave responds. The mes-
sage format is configured for both sending and receiving as shown below, and the length of data packets is
changed by the command (function) contents.

Slave address
Function code

Data

Error check
The space between messages must support the following.

PLC to Inverter Inverter to PLC PLC to Inverter

Command message Response message Command message

Time (Seconds)

24 bits long H5-06 24 bits long 5 ms min.

setting

Fig 6.60 Message Spacing

Slave Address
Set the Inverter address from 0 to 20 Hex. If you set 0, commands from the master will be broadcast (i.e., the
Inverter will not return responses).

6-95
 Function Code
The function code specifies commands. There are three function codes, as shown below.
Command Message Response Message
Function Code
Function Min. Max. Min. Max.
(Hexadecimal)
(Bytes) (Bytes) (Bytes) (Bytes)
03H Read storage register contents 8 8 7 37
08H Loopback test 8 8 8 8
10H Write multiple storage registers 11 41 8 8

Data
Configure consecutive data by combining the storage register address (test code for a loopback address) and
the data the register contains. The data length changes depending on the command details.

Error Check
Errors are detected during communications using CRC-16. Perform calculations using the following method.
1. The factory setting for CRC-16 communications is usually 0, but when using the MEMOBUS system, set
the factory setting to 1 (i.e., set all 16 bits to 1).
2. Calculate CRC-16 using MSB as slave address LSB, and LSB as the MSB of the final data.
3. Also calculate CRC-16 for response messages from the slaves, and compare them to the CRC-16 in the
response messages.

6-96
 Individual Functions

„MEMOBUS Message Example

An example of MEMOBUS command/response messages is given below.

Reading Storage Register Contents

Read the contents of the storage register only for specified quantities whose addresses are consecutive, starting
from a specified address. The contents of the storage register are separated into higher place 8 bits and lower
place 8 bits, and comprise the data within response messages in address order.
The following table shows message examples when reading status signals, error details, data link status, and
frequency references from the slave 2 Inverter.

Response Message Response Message

Command Message
(During Normal Operation) (During Error)
Slave Address 02H Slave Address 02H Slave Address 02H
Function Code 03H Function Code 03H Function Code 83H
Higher
00H Data quantity 08H Error code 03H
Start place
Address Lower Higher Higher
20H 00H F1H
place Lead stor- place place
CRC-16
Higher age register Lower Lower
00H 65H 31H
place place place
Quantity
Lower Higher
04H 00H
place Next stor- place
Higher age register Lower
45H 00H
place place
CRC-16
Lower Higher
F0H 00H
place Next stor- place
age register Lower
00H
place
Higher
01H
Next stor- place
age register Lower
F4H
place
Higher
AFH
place
CRC-16
Lower
82H
place

6-97
 Loopback Test
The loopback test returns command messages directly as response messages without changing the contents to
check the communications between the master and slave. You can set user-defined test code and data values.
The following table shows a message example when performing a loopback test with the slave 1 Inverter.
Response Message Response Message
Command Message
(During Normal Operation) (During Error)
Slave address 01H Slave address 01H Slave address 01H
Function code 08H Function code 08H Function code 89H
Higher Higher
00H 00H Error Code 01H
place place
Test Code Test Code
Lower Lower Higher
00H 00H 86H
place place place
CRC-16
Higher Higher Lower
A5H A5H 50H
place place place
Data Data
Lower Lower
37H 37H
place place
Higher Higher
DAH DAH
place place
CRC-16 CRC-16
Lower Lower
8DH 8DH
place place

Writing to Multiple Storage Registers

Write the specified data to each specified storage register from the specified addresses. The written data must
be in the following order in the command message: Higher place 8 bits, then lower place 8 bits, in storage reg-
ister address order.
The following table shows an example of a message when forward operation has been set at a frequency refer-
ence of 60.0 Hz in the slave 1 Inverter by the PLC.
Response Message Response Message
Command Message
(During Normal Operation) (During Error)
Slave Address 01H Slave Address 01H Slave Address 01H
Function Code 10H Function Code 10H Function Code 90H
Higher Higher
00H 00H Error code 02H
Start place Start place
Address Lower Address Lower Higher
01H 01H CDH
place place place
CRC-16
Higher Higher Lower
00H 00H C1H
place place place
Quantity Quantity
Lower Lower
02H 02H
place place
Higher
No. of data 04H 10H
place
CRC-16
Higher Lower
00H 08H
place place
Lead data
Lower
01H
place
Higher
02H
place
Next data
Lower
58H
place
Higher
63H
place
CRC-16
Lower
39H
place

6-98
 Individual Functions

Set the number of data specified using command messages as quantity of specified messages x 2. Handle
response messages in the same way.

INFO

„Data Tables
The data tables are shown below. The types of data are as follows: Reference data, monitor data, and broadcast
data.

Reference Data
The reference data table is shown below. You can both read and write reference data.
Register No. Contents
0000H Not used
Frequency reference
Bit 0 Forward Run/Stop Command 1: Forward run 0: Stop
Bit 1 Reverse Run/Stop Command 1: Reverse run 0: Stop
Bit 2 External fault 1: Error (EFO)
Bit 3 Fault reset 1: Reset command
Bit 4 ComNet
Bit 5 ComCtrl
Bit 6 Multi-function input command 3
0001H Bit 7 Multi-function input command 4
Bit 8 Multi-function input command 5
Bit 9 Multi-function input command 6
Bit A Multi-function input command 7
Bit B Multi-function input command 8
Bit C Multi-function input command 9
Bit D Multi-function input command 10
Bit E Multi-function input command 11
Bit F Multi-function input command 12
0002H Frequency reference (Set units using constant o1-03)
0003H Not used
0004H Not used
0005H Not used
0006H PID target value
0007H Analog output 1 setting (-11 V/-1540 to 11 V/1540)
0008H Analog output 2 setting (-11 V/-1540 to 11 V/1540)
Multi-function contact output setting
Bit 0 Contact output (Terminal M1-M2) 1: ON 0: OFF
Bit 1 PHC1(Contact P1-PC) 1: ON 0: OFF
Bit 2 PHC2(Contact P2-PC) 1: ON 0: OFF
Bit 3 PHC3(Contact P3-C3) 1: ON 0: OFF
0009H
Bit 4 PHC4(Contact P4-C4) 1: ON 0: OFF
Bit 5 Not used
Bit 6 Set error contact (terminal MA-MC) output using bit 7. 1: ON 0: OFF
Bit 7 Error contact (terminal MA-MC) 1: ON 0: OFF
Bits 8 to F Not used
000AH to 000EH Not used

6-99
 Register No. Contents
Reference selection settings
Bit 0 Not used
Bit 1 Use MEMOBUS 0006H PID target value 1: Enabled 0: Disabled
Bits 2 to B Not used
000FH
C Broadcast data terminal S5 input 1: Enabled 0: Disabled
D Broadcast data terminal S6 input 1: Enabled 0: Disabled
E Broadcast data terminal S7 input 1: Enabled 0: Disabled
F Broadcast data terminal S8 input 1: Enabled 0: Disabled
Note Write 0 to all unused bits. Also, do not write data to reserved registers.

Monitor Data
The following table shows the monitor data. Monitor data can only be read.
Register No. Contents
Inverter status
Bit 0 Operation 1: Operating 0: Stopped
Bit 1 Reverse operation 1: Reverse operation 0: Forward operation
Bit 2 Inverter startup complete 1: Completed 2: Not completed
Bit 3 Error 1: Error
Bit 4 Data setting error 1: Error
0020H
Bit 5 Multi-function contact output (terminal M1 - M2) 1: ON 0: OFF
Bit 6 Multi-function PHC output 1 (terminal P1 - PC) 1: ON 0: OFF
Bit 7 Multi-function PHC output 2 (terminal P2 - PC) 1: ON 0: OFF
Bit 8 Multi-function PHC output 3 (terminal P3 - C3) 1: ON 0: OFF
Bit 9 Multi-function PHC output 4 (terminal P4 - C4) 1: ON 0: OFF
Bits A and B Not used
Error details
Bit 0 Overcurrent (OC) Ground fault (GF)
Bit 1 Main circuit overvoltage (OV)
Bit 2 Inverter overload (OL2)
Bit 3 Inverter overheat (OH1, OH2)
Bit 4 Injection brake transistor resistance overheat (rr, rH)
Bit 5 Fuse blown (PUF)
Bit 6 PID feedback reference lost (FbL)
Bit 7 External fault (EF, EFO)
0021H Bit 8 Hardware error (CPF)
Motor overload (OL1), overtorque 1 (OL3) detected, or overtorque 2 (OL4)
Bit 9
detected
Bit A PG broken wire detected (PGO), Overspeed (OS), Speed deviation (DEV)
Bit B Main circuit undervoltage (UV) detected
Main circuit undervoltage (UV1), control power supply error (UV2), inrush preven-
Bit C
tion circuit error (UV3), power loss
Bit D Main Circuit Voltage Fault (PF), Output Open-phase (LF)
Bit E MEMOBUS communications error (CE)
Bit F Operator disconnected (OPR)
Data link status
Bit 0 Writing data
Bit 1 Not used
0022H Bit 2 Not used
Bit 3 Upper and lower limit errors
Bit 4 Data integrity error
Bits 5 to F Not used
0023H Frequency reference (U1-01)
0024H Output frequency (U1-02)
0025H Output voltage reference (U1-06)
0026H Output current (U1-03) (Unit: 1/0.1A)
0027H Output power (U1-08)

6-100
 Individual Functions

Register No. Contents

0028H Torque reference (U1-09)
0029H Not used
002AH Not used
Sequence input status
Bit 0 1: Control circuit terminal S1 ON
Bit 1 1: Control circuit terminal S2 ON
Bit 2 1: Control circuit terminal S3 ON
Bit 3 1: Control circuit terminal S4 ON
Bit 4 1: Control circuit terminal S5 ON
Bit 5 1: Control circuit terminal S6 ON
002BH
Bit 6 1: Control circuit terminal S7 ON
Bit 7 1: Control circuit terminal S8 ON
Bit 8 1: Control circuit terminal S9 ON
Bit 9 1: Control circuit terminal S10 ON
Bit A 1: Control circuit terminal S11 ON
Bit B 1: Control circuit terminal S12 ON
Bits C to F Not used
Inverter status
Bit 0 Operation 1: Operating
Bit 1 Zero-speed 1: Zero-speed
Bit 2 Frequency matching 1: Matched
Bit 3 User-defined speed matching 1: Matched
Bit 4 Frequency detection 1 1: Output frequency ≤ L4-01
Bit 5 Frequency detection 2 1: Output frequency ≥ L4-01
Bit 6 Inverter startup completed 1: Startup completed
002CH Bit 7 Low voltage detection 1: Detected
Bit 8 Baseblock 1: Inverter output baseblock
Bit 9 Frequency reference mode 1: Not communications 0: Communications
Bit A Run Command mode 1: Not communications 0: Communications
Bit B Overtorque detection 1: Detected
Bit C Frequency reference lost 1: Lost
Bit D Retrying error 1: Retrying
Bit E Error (including MEMOBUS communications time-out) 1:Error occurred
Bit F MEMOBUS communications time-out 1: Timed out
Multi-function contact output status
Bit 0 Multi-function contact output (terminal M1-M2) 1: ON 0: OFF
Bit 1 Multi-function PHC output 1 (terminal P1 - PC) 1: ON 0: OFF
002DH Bit 2 Multi-function PHC output 2 (terminal P2 - PC) 1: ON 0: OFF
Bit 3 Multi-function PHC output 3 (terminal P3 - C3) 1: ON 0: OFF
Bit 4 Multi-function PHC output 4 (terminal P4 - C4) 1: ON 0: OFF
Bits 5 to F Not used
002EH - 0030H Not used
0031H Main circuit DC voltage
0032H Torque monitor (Unit: 1/0.1%)
0033H Output power (U1-08)
0034H - 0037H Not used
0038H PID feedback quantity (Input equivalent to 100%/Max. output frequency; 10/1%; without sign)
0039H PID input quantity (±100%/±Max. output frequency; 10/1%; with sign)
003AH PID output quantity (±100%/±Max. output frequency; 10/1%; with sign)
003BH CPU software number
003CH Flash software number

6-101
 Register No. Contents
Communications error details
Bit 0 CRC error
Bit 1 Invalid data length
Bit 2 Not used
003DH Bit 3 Parity error
Bit 4 Overrun error
Bit 5 Framing error
Bit 6 Time-out
Bits 7 to F Not used
003EH kVA setting
003FH Control method
Note Communications error details are stored until an fault reset is input (you can also reset while the Unit is operating).

Broadcast Data
The following table shows the broadcast data. You can also write this data.
Register
Contents
Address
Operation signal
Bit 0 Run Command 1: Operating 0: Stopped
Bit 1 Reverse operation command 1: Reverse 0: Forward
Bits 2 and 3 Not used
Bit 4 External fault 1: Error (set using H1-01)
0001H Bit 5 Fault reset 1: Reset command (set using H1-02)
Bits 6 to B Not used
Bit C Multi-function contact input terminal S5 input
Bit D Multi-function contact input terminal S6 input
Bit E Multi-function contact input terminal S7 input
Bit F Multi-function contact input terminal S8 input
Frequency ref-
0002H 30000/100%
erence
Note Bit signals not defined in the broadcast operation signals use local node data signals continuously.

„ENTER Command
When writing constants to the Inverter from the PLC using MEMOBUS communications, the constants are
temporarily stored in the constant data area in the Inverter. To enable these constants in the constant data area,
use the ENTER command.
There are two types of ENTER commands: ENTER commands that enable constant data in RAM, and
ENTER commands that write data to EEPROM (non-volatile memory) in the Inverter at the same time as
enabling data in RAM.
The following table shows the ENTER command data. ENTER command data can only be written.
The ENTER command is enabled by writing 0 to register number 0900H or 0901H.
Register No. Contents
0900H Write constant data to EEPROM
0910H Constant data is not written to EEPROM, but refreshed in RAM only.

The maximum number of times you can write to EEPROM using the Inverter is 100 thousand. Do not fre-
quently execute ENTER commands (0900H) written to EEPROM.
The ENTER command registers are write-only. Consequently, if reading these registers, the register address
will become invalid (Error code: 02H).
INFO

6-102
 Individual Functions

„Error Codes
The following table shows MEMOBUS communications error codes.
Error Code Contents
Function code error
01H
A function code other than 03H, 08H, or 10H has been set by the PLC.
Invalid register number error
02H • The register address you are attempting to access is not recorded anywhere.
• With broadcast sending, a start address other than 0000H, 0001H, or 0002H has been set.
Invalid quantity error
03H • The number of data packets being read or written is outside the range 1 to 16.
• In write mode, the number of data packets in the message is not No. of packets x 2.
Data setting error
• A simple upper limit or lower limit error has occurred in the control data or when writing con-
21H
stants.
• When writing constants, the constant setting is invalid.
Write mode error
• Attempting to write constants from the PLC during operation.
• Attempting to write via ENTER commands from the PLC during operation.
22H
• Attempting to write constants other than A1-00 to A1-05, E1-03, or 02-04 when warning alarm
CPF03 (defective EEPROM) has occurred.
• Attempting to write read-only data.
Writing during main circuit undervoltage (UV) error
23H • Writing constants from the PLC during UV (main circuit undervoltage) alarm.
• Writing via ENTER commands from the PLC during UV (main circuit undervoltage) alarm.
Writing error during constants processing
24H
Attempting to write constants from the PLC while processing constants in the Inverter.

„Slave Not Responding

In the following cases, the slave will ignore the write function. If the slave address specified in the command
message is 0, all slaves execute the write function, but do not return response messages to the master.
• When a communications error (overrun, framing, parity, or CRC-16) is detected in the command message.
• When the slave address in the command message and the slave address in the Inverter do not agree.
• When the data that configures the message and the data time length exceeds 24 bits.
• When the command message data length is invalid.

Application Precautions
Set a timer in the master to monitor response time from the slaves. Make the setting so that if no response is
sent to the master from the slave within the set time, the same command message is sent again from the mas-
ter.

6-103
 „Self-Diagnosis
The Inverter has a built-in function for self-diagnosing the operations of serial communications interface cir-
cuits. This function is called the self-diagnosis function. The self-diagnosis function connects the communica-
tions parts of the send and receive terminals, receives the data sent by the Inverter, and checks if
communications are being performed normally.
Perform the self-diagnosis function using the following procedure.
1. Turn ON the power supply to the Inverter, and set 67 (communications test mode) in constant H1-05 (Ter-
minal S7 Function Selection).
2. Turn OFF the power supply to the Inverter.
3. Perform wiring according to the following diagram while the power supply is turned OFF.
4. Turn ON the terminating resistance. (Turn ON pin 1 on DIP switch 1.)
5. Turn ON the power supply to the Inverter again.

Fig 6.61 Details of Communications Terminals

“Pass” will be displayed if self-diagnosis is completed without an error occurring.

If an error occurs, a CE (MEMOBUS communications error) alarm will be displayed on the Digital Operator,
the error contact output will be turned ON, and the Inverter operation ready signal will be turned OFF.

6-104
 Individual Functions

‹ Using the Timer Function

Multi-function contact input terminals S3 to S12 can be designated as timer function input terminals, and
multi-function output terminals M1-M2, P1-PC, P2-PC, P3-C3, and P4-C4 can be designated as timer func-
tion output terminals. By setting the delay time, you can erase chattering from the sensors and switches.
• Set one of the constants H1-01 to H1-10 (multi-function contact input terminal S3 to S12) to 18 (timer
function input).
• Set H2-01 to H2-03 (multi-function output terminals M1-M2, P1-PC, P2-PC, P3-C3, and P4-C4 function
selection) to 12 (timer function output).

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Timer function Sets the timer function output
ON-delay time ON-delay time (dead band) for
the timer function input, in 1-sec- 0.0 to
b4-01 0.0 s No A A A A A 1A3H
ond units. 300.0
ON 延迟时间 Enabled when a timer function is
set in H1-†† or H2-††.

Timer function Sets the timer function output

OFF-delay time OFF-delay time (dead band) for
the timer function input, in 1-sec- 0.0 to
b4-02 0.0 s No A A A A A 1A4H
ond units. 300.0
OFF 延迟时间 Enabled when a timer function is
set in H1-†† or H2-††.

„Setting Example
When the timer function input ON time is longer than the value set in b4-01, the timer output function is
turned ON. When the timer function input OFF time is longer than the value set in b4-02, the timer output
function is turned OFF. An example of timer function operation is given in the following diagram.

Timer function input

Timer function output

Fig 6.62 Timer Function Operation Example

6-105
 ‹ Using PID Control
PID control is a method of making the feedback value (detection value) match the set target value. By combin-
ing proportional control (P), integral control (I), and derivative control (D), you can even control targets
(machinery) with play time.
The characteristics of the PID control operations are given below.

P control Outputs the amount of operation proportional to the deviation. You cannot, however, set the
deviation to zero using P control alone.
I control Outputs the amount of operation that integrates the deviation. Used for matching feedback
value to the target value. I control is not suited, however, to rapid variations.
D control Outputs the amount of operation derived from the deviation. Can respond promptly to rapid
variations.

„PID Control Operation

To understand the differences between each PID control operation (P, I, and D, the variation in the amount of
operation (output frequency) is as shown in the following diagram when the deviation (i.e., the difference
between the target value and feedback value) is fixed.

Deviation
Time

PID control
Amount of operation I control
D control

P control
Time

Fig 6.63 PID Control Operation

„PID Control Applications

The following table shows examples of PID control applications using the Inverter.
Applica- Example of Sen-
Control Details
tion sor Used
• Feeds back machinery speed information, and matches speed to the target value.
Speed Con- Tachometer genera-
• Inputs speed information from other machinery as the target value, and performs
trol tor
synchronous control using the actual speed feedback.
Pressure
Feeds back pressure information, and performs constant pressure control. Pressure sensor
Control
Flow Rate
Feeds back flow rate information, and controls the flow rate highly accurately. Flow rate sensor
Control
Tempera-
Feeds back temperature information, and performs temperature adjustment control • Thermocouple
ture Con-
by rotating the fan. • Thermistor
trol

6-106
 Individual Functions

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
PID control 0: Disabled
method selec- 1: Enabled (Deviation is D-
tion controlled.)
2: Enabled (Feedback value is D-
controlled.)
3: PID control enabled
b5-01 0 to 4 0 No A A A A A 1A5H
(frequency reference + PID
PID 控制选择 output, D control of deviation)
4: PID control enabled
(frequency reference + PID
output, D control of feedback
value).
Proportional Sets P-control proportional gain
0.00
gain (P) as a percentage.
b5-02 to 1.00 Yes A A A A A 1A6H
P-control is not performed when
PID 增益 25.00
the setting is 0.00.

Integral (I) time Sets I-control integral time in 1-

second units. 0.0 to
b5-03 1.0 s Yes A A A A A 1A7H
PID 积分时间 I-control is not performed when 360.0
the setting is 0.0.

Integral (I) limit Sets the I-control limit as a per-

0.0 to 100.0
b5-04 centage of the maximum output Yes A A A A A 1A8H
PID 时间上限 100.0 %
frequency.

Derivative (D) Sets D-control derivative time in

time 1-second units. 0.00 to
b5-05 0.00 s Yes A A A A A 1A9H
D-control is not performed when 10.00
PID 微分时间 the setting is 0.00.
PID upper limit Sets the upper limit after PID-
0.0 to 100.0
b5-06 control as a percentage of the Yes A A A A A 1AAH
PID 上限 100.0 %
maximum output frequency.
PID offset Sets the offset after PID-control -100.0
b5-07 adjustment as a percentage of the maximum to 0.0% Yes A A A A A 1ABH
PID 偏置 output frequency. +100.0

PID first order Sets the time constant for low

lag time con- pass filter for PID-control outputs 0.00 to
b5-08 stant 0.00 s Yes A A A A A 1ACH
in 1-second units. 10.00
PID 延迟时间 Not usually necessary to set.

PID output Select forward/reverse for PID

characteristics output.
b5-09 selection 0: PID output is forward. 0 or 1 0 No A A A A A 1ADH
1: PID output is reverse
输出特性选择 (highlights the output code)
PID output gain 0.0 to
b5-10 Sets output gain. 1.0 No A A A A A 1AEH
PID 输出增益 25.0

PID reverse 0: 0 limit when PID output is

output selection negative.
1: Reverses when PID output is
b5-11 0 or 1 0 No A A A A A 1AFH
negative.
输出逆转选择 0 limit when reverse prohibit is
selected using b1-04.

6-107
 Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Selection of 0: No detection of loss of PID
PID feedback feedback.
command loss 1: Detection of loss of PID
detection feedback.
Operation continues during
detection, with the
b5-12 malfunctioning contact not 0 to 2 0 No A A A A A 1B0H
operating.
反馈丧失检出 2: Detection of loss of PID
feedback.
Coasts to stop during
detection, and fault contact
operates.

PID feedback
command loss Sets the PID feedback loss detec-
detection level tion level as a percent units, with 0 to
b5-13 0% No A A A A A 1B1H
the maximum output frequency at 100
反馈丧失 100%.
检出值

PID feedback
command loss
detection time Sets the PID feedback loss detec- 0.0 to
b5-14 1.0 s No A A A A A 1B2H
tion level in s units. 25.5
反馈丧失检出时
间

PID sleep func-

tion operation Set the PID sleep function start 0.0 to
b5-15 level 0.0 Hz No A A A A A 1B3H
level as a frequency. 400.0
暂停动作值

PID sleep oper-

ation delay time Set the delay time until the PID 0.0 to
b5-16 0.0 s No A A A A A 1B4H
暂停动作延迟时
sleep function starts in seconds. 25.5
间

Accel/decel
time for PID
reference Set the accel/decel time for PID 0.0 to
b5-17 0.0 s No A A A A A 1B5H
reference in seconds. 25.5
PID 加减速
时间

Pulse train
input function 0: Frequency reference
H6-01 selection 1: PID feedback value 0 to 2 0 No A A A A A 42CH
2: PID target value
脉冲输入选择

Monitor Functions

Name Control Methods

Con- Output Signal Level Open Open MEMO
Min. V/f Loop Flux Loop BUS
stant Description During Multi-Func- Unit Reg-
Number Display V/f with Vec- Vec- Vec-
tion Analog Output PG tor tor tor ister
1 2
PID feed- Monitors the feedback value
back value when PID control is used.
10 V: Max. frequency 0.01
U1-24 The input for the max. fre- A A A A A 57H
(-10 to 10 V possible) %
PID 反馈 quency corresponds to
100%.

6-108
 Individual Functions

Name Control Methods

Con- Output Signal Level Open Open MEMO
Min. V/f Loop Flux Loop BUS
stant Description During Multi-Func- Unit Reg-
Number Display V/f with Vec- Vec- Vec-
tion Analog Output PG tor tor tor ister
1 2
PID input PID feedback volume
volume 10 V: Max. frequency 0.01
U1-36 Given as maximum fre- A A A A A 58H
(-10 to 10 V possible) %
PID 的输入量 quency/100%

PID output PID control output

volume 10 V: Max. frequency 0.01
U1-37 Given as maximum fre- A A A A A 59H
(-10 to 10 V possible) %
PID 的输出量 quency/100%

PID com- PID command + PID com-

mand mand bias 0.01
U1-38 10 V: Max. frequency A A A A A 5AH
Given as maximum fre- %
PID 目标值 quency/100%

Multi-Function Contact Inputs (H1-01 to H1-10)

Control Methods
Set- Open Open
ting Function V/f Loop Flux Loop
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
19 PID control disable (ON: PID control disabled) Yes Yes Yes Yes Yes

PID control integral reset (reset when reset command is input or when stopped during
30 Yes Yes Yes Yes Yes
PID control)
31 PID control integral hold (ON: Hold) Yes Yes Yes Yes Yes

34 PID soft starter Yes Yes Yes Yes Yes

35 PID input characteristics switch Yes Yes Yes Yes Yes

Multi-Function Analog Input (H3-05, H3-09)

Control Methods
Set- Open Open
ting Function Contents (100%) V/f Loop Flux Loop
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
B PID feedback Maximum output frequency Yes Yes Yes Yes Yes

C PID target value Maximum output frequency Yes Yes Yes Yes Yes

„PID Control Methods

There are four PID control methods. Select the method by setting constant b5-01.
Set Value Control Method
PID output becomes the Inverter output frequency, and D control is used in the difference between PID
1
target value and feedback value.
2 PID output becomes the Inverter output frequency, and D control is used in the PID feedback value.
PID output is added as compensation value of the Inverter output frequency, and D control is used in the
3
difference between PID target value and feedback value.
PID output is added as compensation value of the Inverter output frequency, and D control is used in the
4
PID feedback value.

6-109
 „PID Input Methods
Enable PID control using constant b5-01, and set the PID target value and PID feedback value.

PID Target Value Input Methods

Select the PID control target value input method according to the setting in b1-01 (Reference Selection).
Normally, the frequency reference selected in b1-01 is the PID target value, but you can also set the PID target
value as shown in the following table.

PID Target Input Method Setting Conditions

Set H3-05 or H3-09 to C (PID target value). Also, be sure to set H6-01 (pulse train input
Multi-Function Analog Ter-
function selection) to 1 (PID feedback value).
minal A2, or A3 Input
The negative inputs cannot be used for target values.
Set MEMOBUS bit 1 in register address 000FH to 1 (enable/disable PID target value
MEMOBUS register 0006H
from communications) to be able to use register number 0006H as the PID target value.
Pulse train input Set H6-01 to 2 (PID target value).

PID Feedback Input Methods

Select one of the following PID control feedback input methods.

Input Method Setting Conditions

Set H3-09 (Multi-function Analog Input Terminal A2 Selection) or H3-05 (Multi-func-

Multi-function analog input
tion Analog Input Terminal A3 Function Selection) to B (PID feedback).
Pulse train input Set H6-01 to 1 (PID feedback).

Adjust PID target value and PID feedback value using the following items.
• Analog input: Adjust using the analog input terminal gain and bias.
• Pulse train input: Adjust using pulse train scaling, pulse train input gain, and pulse train input bias.
INFO

„PID Adjustment Methods

Use the following procedure to adjust PID while performing PID control and measuring the response wave-
form.
1. Set b5-01 (PID Control Method Selection) to 1 or 2 (PID control enabled).
2. Increase b5-02 (Proportional Gain (P)) to within a range that does not vibrate.
3. Reduce b5-03 (Integral (I) time) to within a range that does not vibrate.
4. Increase b5-05 (Derivative (D) time) to within a range that does not vibrate.

6-110
 Individual Functions

„PID Fine Adjustment Methods

This section explains the fine adjustment of PID after setting the PID control constants.

Suppressing Overshoot
If overshoot occurs, reduce derivative time (D), and increase integral time (I).

Response Before adjustment

After adjustment

Time

Set a Rapidly Stabilizing Control Condition

To rapidly stabilize the control even if overshoot occurs, reduce integral time (I), and lengthen derivative time
(D).

Response
Before adjustment

After adjustment

Time

Suppressing Long-cycle Vibration

If vibration occurs with a longer cycle than the integral time (I) set value, the integral operation is too strong.
Lengthen the integral time (I) to suppress the vibration.

Response Before adjustment

After adjustment

Time

6-111
 Suppressing Short Cycle Vibration
If vibration occurs when the vibration cycle is short, and the cycle is almost identical to the derivative time (D)
set value, the differential operation is too strong. Shorten the derivative time (D) to suppress the vibration.
If vibration continues even when the derivative time (D) is set to 0.00 (D control disabled), reduce the propor-
tional gain (P), or increase the PID primary delay time constant.

Response Before adjustment

After adjustment

Time

„Setting Precautions
• In PID control, the b5-04 constant is used to prevent the calculated integral control value from exceeding a
specified amount. If the load changes rapidly, the machine may be damaged or the motor may stall because
of unpredictable response from the Inverter. In this case, reduce the set value.
• The b5-06 constant is used to prevent the arithmetic operation following the PID control calculation from
exceeding a specified amount. Set taking the maximum output frequency to be 100%.
• The b5-07 constant is used to adjust PID control offset. Set in increments of 0.1%, taking the maximum
output frequency to be 100%.
• Set the low pass filter time constant for the PID control output in b5-08. Enable this constant to prevent
machinery resonance from occurring when machinery adhesive abrasion is great, or rigidity is poor. In this
case, set the constant to be greater than the resonance frequency cycle. Increase this time constant to
reduce Inverter responsiveness.
• Using b5-09, you can invert the PID output polarity. Consequently, if you increase the PID target value,
you can apply this constant to applications to lower the Inverter output frequency.
• Using b5-10, you can apply gain to the PID control output. Enable this constant to adjust the amount of
compensation if adding PID control output to the frequency reference as compensation.
• When PID control output is negative, you can use constant b5-11 to invert the Inverter. When b1-04 (Pro-
hibition of Reverse Operation) is set to 1 (enabled), however, PID output limit is 0.
• With the Inverter, by setting an independent acceleration/deceleration time in constant b5-17, you can
increase or decrease the PID target value using the acceleration/deceleration time. The acceleration/
deceleration function (constant C1) used normally, however, is allocated after PID control, so depending
on the settings, resonance with PID control and hunting in the machinery may occur. If this happens,
reduce constant C1 until hunting does not occur, and maintain the acceleration/deceleration time using b5-
17. Also, you can disable the set value in b5-17 from the external terminals during operation using multi-
function input set value 34 (PID soft starter ON/OFF).

6-112
 b1-01

Pulse train input

4

Option Card 3
Frequency reference
using multi-step command
Serial Com b5-01=0 Enable/disable reverse operation
2 Frequency reference when PI output is negative
b5-01=3,4 Upper limit
(U1-01)
1 Fmax x109%
Terminal A1 PID OFF +
1 b5-11=0
Output frequency
b5-17 (U1-02)
„PID Control Block

+
0 b5-01=1,2
d1-01 Lower limit 0
0 PID ON b5-11=1
PID SFS Cancel Multi-function input PID control cancel
signal is ON. PID is OFF under the Upper limit
d1-02 Fmax x109%
following conditions:
b5-01 = 0
During JOG command input
Lower limit
d1-16 -(Fmaxx109%)

Pulse input terminal RP

H6-01=2 PID output monitor
PID target value (U1-37)
MEMOBUS communications (U1-38)
register 06 H PID target value
Set bit 1 of MEMOBUS
Terminal A2 or A3 PID register 0FH to 1
target value
Set PID target value in
multi-function analog input

Fig 6.64 PID Control Block

Terminal A2 or A3 PID
The following diagram shows the PID control block in the Inverter.

feedback H3-05 or
H3-09=B
Pulse input terminal RP PID input volume PID output
H6-01=1 (U1-36) gain (b5-10)
+
+ Store integral using Integral rset using
P multi-function inputs multi-function inputs
+
b5-01=2,4 Proportional -1 Integral Integral (I)
+ time PID first order lag
gain (P) (I) time
b5-05 b5-04 time constant 0
b5-02 b5-03 PID Limit
Derivative (D) + b5-08 1
time + + + + +
Z -1 1 1
b5-01=1,3 T T
Select multi-function inputs
+ + + -1 +
PID input characteristics
PID feed-back Z -1 1
Z -1 PID upper
value (U1-24) limit PID offset
b5-01=1,3 b5-06 adjustment (b5-07)
+
b5-05 Select PID output
characteristics selection
Z-1 Derivative (b5-09)
b5-01=2,4
time
Individual Functions

6-113
 „PID Feedback Loss Detection
When performing PID control, be sure to use the PID feedback loss detection function. If PID feedback is lost,
the Inverter output frequency may accelerate to the maximum output frequency.
When setting b5-12 to 1 and the status of the PID feedback value detection level in b5-13 is insufficient and
continues for the time set in b5-14, an FbL (PID feedback reference lost) alarm will be displayed on the Digi-
tal Operator and Inverter operation will continue.
When b5-12 is set to 2, an FbL (PID feedback reference lost) error alarm will be displayed on the Digital
Operator, the error contact will operate, and Inverter operation will be stopped.
The time chart for PID feedback loss detection (set b5-12 to 2) is shown below.

PID feedback value

Loss detection
level
(b5-13)

Time
No FbL
detection
FbL detection
Loss detection time Loss detection time
(b5-14) (b5-14)

Fig 6.65 PID Feedback Loss Detection Time Chart

„PID Sleep
The PID sleep function stops the Inverter when the PID sleep function delay time continues while the PID
control target value is at an insufficient level to operate the PID sleep function. When the PID sleep delay time
continues and the PID control target value is above the PID sleep function operation level, Inverter operation
will automatically resume.
When PID control is disabled, the PID sleep function is also disabled. When using the PID sleep function,
select decelerate to stop or coast to stop as the stopping method.
The PID sleep time chart is shown below.

PID target value

Sleep operation
level b5-15
Sleep operation Sleep operation
delay time delay time
b5-16 b5-16
Internal Run Command
Operation Stopped
Run Command has been input
External Run Command
Operation status output
Operating

Fig 6.66 PID Sleep Time Chart

6-114
 Individual Functions

‹ Energy-saving
To perform energy saving, set b8-01 (Energy Saving Mode Selection) to 1. Energy-saving control can be per-
formed using both V/f control and vector control. The constants to be adjusted are different for each. In V/f
control, adjust b8-04 to b8-06, and in vector control, adjust b8-02 and b8-03.
„Related Constants
Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Energy-saving Select whether to enable or dis-
mode selection able energy-saving control.
b8-01 0 or 1 0 No A A A A A 1CCH
0: Disable
节能模式设定 1: Enable

Energy-saving Set the energy-saving gain with

gain 0.0 to 0.7
b8-02 the open-loop vector control Yes No No A A A 1CDH
10.0 *1
节能增益 method.

Energy-saving
filter time con- Set the energy-saving filter time
0.00 to 0.50 s
b8-03 stant constant with the open-loop vec- Yes No No A A A 1CEH
10.0 *2
tor control method.
节能滤波时间

Energy-saving Set the maximum motor effi-

coefficient ciency value.
Set the motor rated capacity in 0.0 to 288.20
b8-04 No A A No No No 1CFH
E2-11, and adjust the value by 5% 655.00 *3 *4
节能系数 at a time until output power
reaches a minimum value.

Power detection
filter time con-
stant Set the time constant for output 0 to
b8-05 20 ms No A A No No No 1D0H
power detection. 2000
电力检出滤波时
间

Search opera- Set the limit value of the voltage

tion voltage control range during search opera-
limiter tion.
Perform search operation to opti-
0 to
b8-06 mize operations using minute 0% No A A No No No 1D1H
100
探索运行电压极
variations in voltage using
限 energy-saving control. Set to 0 to
disable the search operation.
100% is the motor base voltage.

Motor rated slip Sets the motor rated slip in Hz

units.
These set values will become the 2.90
0.00 to
E2-02 reference values for slip compen- Hz No A A A A A 30FH
电机额定滑差 20.00
sation. *4
This constant is automatically set
during autotuning.

Motor rated Set the rated output of the motor

output in units of 0.01 kW. 0.00 to 0.40
E2-11 No Q Q Q Q Q 318H
This constant is automatically set 650.00 *4
电机额定功率 during autotuning.
* 1. The factory setting is 1.0 when using flux vector control.
* 2. The factory setting is 2.00 s when Inverter capacity is 55 kW min.
The factory setting will change when the control method is changed. The open-loop vector 1 factory setting is given.
* 3. By setting E2-11 (Motor rated output) the appropriate value will be set.
* 4. The factory settings depend on the Inverter capacity. The values for a 200 V Class Inverter of 0.4 kW are given.

6-115
 „Adjusting Energy-saving Control
The method of adjustment during energy-saving control operations differs depending on the control method.
Refer to the following when making adjustments.

V/f Control
In V/f control method, the voltage for optimum motor efficiency is calculated and becomes the output voltage
reference.
• b8-04 (Energy-saving Coefficient) is set at the factory for motor use applied to the Inverter. If the motor
capacity differs from the motor applied to the Inverter, set the motor capacity in E2-11 (Motor Rated Out-
put). Also, adjust the output voltage in steps of 5 until it reaches minimum. The larger the energy-saving
coefficient, the greater the output voltage.
• To improve response when the load fluctuates, reduce the power detection filter time constant b8-05. If b8-
05 is set too small, however, motor rotations when the load is light may become unstable.
• Motor efficiency varies due to temperature fluctuations and differences in motor characteristics. Conse-
quently, control motor efficiency online to optimize efficiency by causing minute variations in voltage
using the search operation. Constant b8-06 (Search Operation Voltage Limiter) controls the range that con-
trol the voltage using the search operation. For 200 V Class Inverters, set the range to 100%/200 V, and for
400 V Class Inverters, set the range to 100%/400 V. Set to 0 to disable the search operation.

Vector Control
In vector control method, control the slip frequency so that motor efficiency is maximized.
• Taking the motor rated slip for the base frequency as optimum slip, calculate the optimum slip for motor
efficiency for each frequency. In vector control, be sure to perform autotuning, and set the motor rated slip.
• If the motor performs hunting when using energy-saving control in vector control, reduce the set value in
b8-02 (Energy-saving Gain), or increase the set value in b8-03 (Energy-saving Filter Time Constant).

6-116
 Individual Functions

‹ Setting Motor Constants

In vector control method, the motor constants are set automatically using autotuning. If autotuning does not
complete normally, set them manually.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Motor rated Sets the motor rated current in 1 A
current units.
These set values will become the
0.32 to
reference values for motor protec- 1.90 A
E2-01 6.40 No Q Q Q Q Q 30EH
tion, torque limits and torque con- *1
*2
电机额定电流 trol.
This constant is automatically set
during autotuning.

Motor rated slip Sets the motor rated slip in Hz

units.
These set values will become the 2.90
0.00 to
E2-02 reference values for slip compen- Hz No A A A A A 30FH
电机额定滑差 20.00
sation. *1
This constant is automatically set
during autotuning.
Motor no-load Sets the motor no-load current in
0.00 to
current 1 A units. 1.20 A
E2-03 1.89 No A A A A A 310H
This constant is automatically set *1
*3
空载电流 during autotuning.

Number of Sets the number of motor poles.

motor poles 4
E2-04 This constant is automatically set 2 to 48 No No Q No Q Q 311H
poles
电机极数 during autotuning.

Motor line-to- Sets the motor phase-to-phase

0.000 9.842
line resistance resistance in Ω units.
E2-05 to Ω No A A A A A 312H
This constant is automatically set
线间电阻 65.000 *1
during autotuning.
Motor leak Sets the voltage drop due to motor
inductance leakage inductance as a percent-
0.0 to 18.2%
E2-06 age of the motor rated voltage. No No No A A A 313H
40.0 *1
电机漏电感 This constant is automatically set
during autotuning.

Motor iron sat- Sets the motor iron saturation

uration coeffi- coefficient at 50% of magnetic
0.00 to
E2-07 cient 1 flux. 0.50 No No No A A A 314H
0.50
This constant is automatically set
饱和系数 1 during rotational autotuning.

Motor iron sat- Sets the motor iron saturation

uration coeffi- coefficient at 75% of magnetic
0.00 to
E2-08 cient 2 flux. 0.75 No No No A A A 315H
0.75
This constant is automatically set
饱和系数 2 during rotational autotuning.
Motor iron loss
for torque com- 0 to 14 W
E2-10 pensation Sets motor iron loss in W units. No A A No No No 317H
65535 *1

铁损

6-117
 Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Motor iron sat- Sets the motor iron saturation
uration coeffi- coefficient at 130% of magnetic
1.30 to
E2-12 cient 3 flux. 1.30 No No No A A A 328H
1.60
This constant is automatically set
饱和系数 3 during rotational autotuning.
* 1. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given.
* 2. The setting range is from 10% to 200% of the Inverter rated output current. The value for a 200 V Class Inverter for 0.4 kW is given.
For the motor no-load current, set E2-03 to a value less than that of E2-01.
* 3. The setting range depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. The upper limit depends on the setting of
E2-01.

„Manual Motor Constant Setting Methods

The motor constants settings methods are given below. Make (enter) settings referring to the motor test report.

Motor Rated Voltage Setting

Set E2-01 to the rated current on the motor nameplate.

Motor Rated Slip Setting

Set E2-02 to the motor rated slip calculated from the number of rated rotations on the motor nameplate.

Amount of motor rated slip = Motor rated frequency (Hz) - No. of rated rotations (min−1) x No. of motor
poles/120.

Motor No-Load Current Setting

Set E2-03 to the motor no-load current using the rated voltage and rated frequency. The motor no-load current
is not normally written on the motor nameplate. Consult the motor manufacturer.
Factory setting is the no-load current value for a standard Yaskawa 4-pole motor.

Number of Motor Poles Setting

Set the number of motor poles (number of poles) as written on the motor nameplate. E2-04 is not displayed
when V/f control or open-loop vector control is selected.

Motor Line-to-Line Resistance Setting

E2-05 is set automatically when performing motor line-to-line resistance autotuning. When you cannot per-
form tuning, consult the motor manufacturer for the line-to-line resistance value. Calculate the resistance from
the line-to-line resistance value in the motor test report using the following formula, and then make the setting
accordingly.
• E-type isolation: [Line-to-line resistance (Ω) at 75°C of test report] × 0.92 (Ω)
• B-type isolation: [Line-to-line resistance (Ω) at 75°C of test report] × 0.92 (Ω)
• F-type isolation: [Line-to-line resistance (Ω) at 115°C of test report] × 0.87 (Ω)

Motor Leak Inductance Setting

Set the amount of voltage drop due to motor leak inductance in E2-06 using the percentage over the motor
rated voltage. Make this setting when the high-speed motor inductance is small. If the inductance is not writ-
ten on the motor nameplate, consult the motor manufacturer.

6-118
 Individual Functions

Motor Iron Saturation Coefficients 1, 2 and 3 Settings

E2-07, E2-08 and E2-12 are set automatically using rotational autotuning.

Motor Iron Loss for Torque Compensation Setting

E2-10 is displayed only when in V/f control method. To increase the torque compensation accuracy when in
V/f control method, set the motor iron loss in Watts.

Motor Mechanical Loss

When using flux vector control, adjust mechanical loss in the following cases. (There is normally no reason to
make this adjustment.) The mechanical loss setting is used to compensate the torque.
• There is excessive torque loss from the motor bearings.
• There is excessive torque loss from a fan, pump, etc.

6-119
 ‹ Setting the V/f Pattern
In V/f control method, you can set the Inverter input voltage and the V/f pattern as the need arises.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Input voltage Set the Inverter input voltage in 1
155 to
setting volt. 200 V
E1-01 255 No Q Q Q Q Q 300H
This setting is used as a reference *1
*1
输入电压 value in protection functions.
V/f pattern 0 to E: Select from the 15 preset
selection patterns.
E1-03 F: Custom user-set patterns 0 to F F No Q Q No No No 302H
V/F 曲线设定 (Applicable for settings E1-04
to E1-10.)

Max. output 40.0 to 50.0

E1-04 frequency 400.0 Hz No Q Q Q Q Q 303H
*5 *2
最高输出频率

Max. voltage 0.0 to 200.0

E1-05 255.0 V No Q Q Q Q Q 304H
最大电压 Output voltage (V) *1 *1*2

Base 0.0 to 50.0

E1-06 frequency 400.0 Hz No Q Q Q Q Q 305H
*5 *2
基本频率

Mid. output
frequency Frequency (Hz) 0.0 to 3.0 Hz
E1-07 No A A A No No 306H
400.0 *2
中间频率 To set V/f characteristics in a
straight line, set the same values for
Mid. output
E1-07 and E1-09. In this case, the 0.0 to
frequency 13.2 V
E1-08 setting for E1-08 will be disre- 255.0 No A A A No No 307H
voltage *1 *2
garded. *1
中间电压 Always ensure that the four fre-
quencies are set in the following
Min. output manner: 0.0 to
frequency 0.5 Hz
E1-09 E1-04 (FMAX) ≥ E1-06 (FA) > E1- 400.0 No Q Q Q A Q 308H
*2
最低输出频率 07 (FB) ≥ E1-09 (FMIN) *5

Min. output
frequency 0.0 to
2.4 V
E1-10 voltage 255.0 No A A A No No 309H
*1 *2
*1
最低输出电压

Mid. output 0.0 to

frequency 2 0.0 Hz
E1-11 400.0 No A A A A A 30AH
*3
*5
中间频率 2

Mid. output
Set only to fine-adjust V/f for the
frequency 0.0 to
output range. Normally, this setting 0.0 V
E1-12 voltage 2 255.0 No A A A A A 30BH
is not required. *1
*3

中间电压 2

Base voltage 0.0 to

0.0 V
E1-13 255.0 No A A Q Q Q 30CH
*4
基本电压 *1

6-120
 Individual Functions

* 1. These are values for a 200 V Class Inverter. Values for a 400 V Class Inverter are double.
* 2. The factory setting will change when the control method is changed. The open-loop vector 1 factory settings are given.
* 3. E1-11 and E1-12 are disregarded when set to 0.0.
* 4. E1-13 is set to the same value as E1-05 by autotuning.
* 5. The setting range for open-loop vector 2 control is 0 to 132.0.

„Setting Inverter Input Voltage

Set the Inverter input voltage correctly in E1-01 to match the power supply voltage. This set value will be the
standard value for the protection function and similar functions.
The overvoltage detection level (OV) and the braking transistor operation level (BTR) vary depending on the
input voltage as shown in the following table.
Inverter Class E1-01 Setting OV Detection Level BTR Operation Level∗
200 V Class All values Approx. 410 V Approx. 394 V
400 V or more Approx. 820 V Approx. 788 V
400 V Class
Less than 400 V Approx. 720 V Approx. 682 V
* These are values of operation levels for braking transistors built in Inverters of 0.4 to 15 kW. Refer to FOR VARISPEED-600 SERIES INVERTER BRAK-
ING UNIT BRAKING RESISTOR UNIT INSTRUCTIONS (TOBPC72060000) for operation levels for separately-installed type Braking Resistor Units.

If selecting a fixed V/f pattern (E1-03 = 0 to E) in V/f control the values of the max. voltage (E1-05), the mid.
Output frequency voltage (E1-08), and the min. output frequency voltage (E1-10) will change if the value for
the input voltage setting (E1-01) is changed.

6-121
 „Setting V/f Pattern
Set the V/f pattern in E1-03 when using V/f control (with or without a PG). There are two methods of setting
the V/f pattern: Select one of the 15 pattern types (set value: 0 to E) that have been set beforehand, or set a
user-defined V/f pattern (set value: F).
The factory setting for E1-03 is F. The contents of E1-03 when factory-set to F are the same as when E1-03 is
set to 1.
To select one of the existing patterns, refer to the following table.
Set
Characteristic Application Specifications
Value
0 (F) 50 Hz specifications

This pattern is used in general applications. 1 60 Hz specifications

Constant Torque Used when the load torque is fixed, regard- 60 Hz specifications, voltage saturation at
Characteristic less of rotation speed, for linear transport 2
50 Hz
systems.
72 Hz specifications, voltage saturation at
3
60 Hz
4 50 Hz specifications,× 3 decrement
This pattern is used for loads with torque 5 50 Hz specifications, × 2 decrement
Variable torque
proportional to two or three times the rota-
characteristic 6 60 Hz specifications, × 3 decrement
tion speed, such as fans and pumps.
7 60 Hz specifications, × 2 decrement
Select the high startup torque V/f pattern 50 Hz specifications, medium startup
8
only in the following cases. torque
• The wiring distance between Inverter and
High Startup motor is large (approx. 150 m min.) 9 50 Hz specifications, large startup torque
Torque (See • A large torque is required at startup (ele-
vator loads, etc.) 60 Hz specifications, medium startup
Note)* • An AC reactor is inserted in the Inverter A
torque
input or output.
• You are operating a motor that is less B 60 Hz specifications, large startup torque
than optimum.
90 Hz specifications, voltage saturation at
C
60 Hz
Fixed Output This pattern is used for frequencies of 60 120 Hz specifications, voltage saturation at
D
Operation Hz or higher. A fixed voltage is applied. 60 Hz
180 Hz specifications, voltage saturation at
E
60 Hz
* The torque is protected by the fully automatic torque boost function, so normally there is no need to use this pattern.

When you select these patterns, the values of constants E1-04 to E1-10 are changed automatically. There are
three types of values for E1-04 to E1-10, depending on the Inverter capacity.
• 0.4 to 1.5 kW V/f pattern
• 2.2 to 45 kW V/f pattern
• 55 to 300 kW V/f pattern
The characteristics diagrams for each are shown in the following pages.

6-122
 Individual Functions

0.4 to 1.5 kW V/f Pattern

The diagrams show characteristics for a 200-V class motor. For a 400-V class motor, multiply all voltages by
2.
• Constant Torque Characteristics (Set Value: 0 to 3)

Set Value 0 50 Hz Set Value 1 60 Hz Set Value 2 60 Hz Set Value 3 72 Hz

(Initial value of set value F)

(1.2)

• Decrement Torque Characteristics (Set Value: 4 to 7)

Set Value 4 50 Hz Set Value 5 50 Hz Set Value 6 60 Hz Set Value 7 60 Hz

• High startup torque (Set value 8: to B)

Set Value 8 50 Hz Set Value 9 50 Hz Set Value A 60 Hz Set Value B 60 Hz

• Fixed Output Operation (Set Value: C to E)

Set Value C 90 Hz Set Value D 120 Hz Set Value E 180 Hz

6-123
 2.2 to 45 kW V/f Pattern
The diagrams show characteristics for a 200-V class motor. For a 400-V class motor, multiply all voltages by 2.
• Constant Torque Characteristics (Set Value: 0 to 3)

Set Value 0 50 Hz Set Value 1 60 Hz Set Value 2 60 Hz Set Value 3 72 Hz

(Initial value of set value F)

(1.2)

• Decrement Torque Characteristics (Set Value: 4 to 7)

Set Value 4 50 Hz Set Value 5 50 Hz Set Value 6 60 Hz Set Value 7 60 Hz

• High Startup Torque (Set Value: 8 to B)

Set Value 8 50 Hz Set Value 9 50 Hz Set Value A 60 Hz Set Value B 60 Hz

• Fixed Output Operation (Set Value: C to E)

Set Value C 90 Hz Set Value D 120 Hz Set Value E 180 Hz

6-124
 Individual Functions

55 to 300 kW V/f Pattern

The diagrams show characteristics for a 200-V class motor. For a 400-V class motor, multiply all voltages by
2.
• Constant Torque Characteristics (Set Value: 0 to 3)

Set Value 0 50 Hz Set Value 1 60 Hz Set Value 2 60 Hz Set Value 3 72 Hz

(Initial value of set value F)

(1.2)

• Decrement Torque Characteristics (Set Value: 4 to 7)

Set Value 4 50 Hz Set Value 5 50 Hz Set Value 6 60 Hz Set Value 7 60 Hz

• High Startup Torque (Set Value: 8 to B)

Set Value 8 50 Hz Set Value 9 50 Hz Set Value A 60 Hz Set Value B 60 Hz

• Fixed Output Operation (Set Value: C to E)

Set Value C 90 Hz Set Value D 120 Hz Set Value E 180 Hz

6-125
 When E1-03 is set to F (User-defined V/f pattern), you can set constants E1-04 to E1-10. If E1-03 is set to
anything other than F, you can only refer to constants E1-04 to E1-10. If the V/f characteristics are linear, set
E1-07 and E1-09 to the same value. In this case, E1-08 will be ignored.

Output voltage (V)

E1-05
(VMAX)

E1-13
(V Base)

E1-08
(VC)

E1-10
(VMIN)

Frequency (Hz)
E1-09 E1-07 E1-06 E1-04
(FMIN) (FB) (FA) (FMAX)

Fig 6.67 User-Set V/f Pattern

„Setting Precautions
When the setting is to user-defined V/f pattern, beware of the following points.
• When changing control method, constants E1-07 to E1-10 will change to the factory settings for that
control method.
• Be sure to set the four frequencies as follows:
E1-04 (FMAX) ≥ E1-06 (FA) > E1-07 (FB) ≥ E1-09 (FMIN)

6-126
 Individual Functions

‹ Torque Control
With flux vector control or open-loop vector 2 control, the motor's output torque can be controlled by a torque
reference from an analog input. To control torque, set d5-01 to 1 or set multi-function contact inputs H1-††
to 71 (Speed/Torque control) and turn ON the contact.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Torque control 0: Speed control (C5-01 to C5-
selection 07)
1: Torque control
This function is only available in
flux vector control method. To
d5-01 0 or 1 0 No No No No A A 29AH
转矩控制选择
use the function for switching
between speed and torque control,
set to 0 and set the multi-function
input to “speed/torque control
change.”

Torque Set the torque reference filter pri-

reference delay mary delay time in ms units.
time This function can be used to
adjust the noise of the torque con- 0 to
d5-02
trol signal or the responsiveness 1000 0* No No No No A A 29BH
转矩控制延迟 with the host controller. When
时间 oscillation occurs during torque
control, increase the set value.

Speed limit Set the speed limit command

selection method for the torque control
method.
d5-03 1: The analog input limit from a 1 or 2 1 No No No No A A 29CH
速度极限选择 frequency reference
2: Limited by d5-04 constant set-
ting values.

Speed limit Set the speed limit during torque

control as a percentage of the
maximum output frequency.
-120
This function is enabled when d5-
d5-04 to 0 No No No No A A 29DH
速度极限 03 is set to 2. Directions are as
+120
follows:
+: Run Command direction
-: Opposite of Run Command

Speed limit bias Set the speed limit bias as a per-

centage of the maximum output
frequency.
0 to
d5-05 Bias is applied to the specified 10 No No No No A A 29EH
速度极限偏置 120
speed limit. It can be used to
adjust the margin for the speed
limit.

6-127
 Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Speed/torque Set the delay time from inputting
control the multi-function input “speed/
switching timer torque control change” (from ON
to OFF or OFF to ON) until the
control is actually changed in ms
units.
This function is enabled when the
0 to
d5-06 multi-function input “speed/ 0 No No No No A A 29FH
1000
torque control change” is set. In
控制切换时间 the speed/torque control switch-
ing timer, the analog inputs hold
the values of when the “speed/
torque control change” changes.
Always be sure to allow time for
this process to finish completely.

Rotation 0: Disabled
direction limit 1: Enabled
operation Usually, use a setting of 1
selection (enabled).
d5-07 0 or 1 1 No No No No No A 2A6H
Be sure to enable this setting
when rotating the motor in the
旋转方向限制
动作 same direction as the speed limit
(winding operation).
Signal level 0: 0 to 10V
selection (ter- 1: -10 to 10V
H3-04 minal A3) 0 or 1 0 No A A A A A 413H
[11-bit + polarity (positive/
端子 A3 信号电平 negative) input]

Multi-function
analog input
(terminal A3) Select multi-function analog input
H3-05 function selec- 0 to 1F 2 No A A A A A 414H
function for terminal A3.
tion

端子 A3 设定

Gain (terminal Sets the input gain (level) when

A3) 10 V is input. 0.0 to 100.0
H3-06 Yes A A A A A 415H
Set according to the 100% value 1000.0 %
端子 A3 增益 selected from H3-05.

Bias (terminal Sets the input gain (level) when

-100.0
A3) 0 V is input.
H3-07 to 0.0% Yes A A A A A 416H
Set according to the 100% value
端子 A3 偏置 +100.0
selected from H3-05.

Signal level0: 0 to 10V

selection 1: -10V to 10V
(terminal A2)
2: 4 to 20 mA (9-bit input).
H3-08 0 to 2 2 No A A A A A 417H
Switch current and voltage input
端子 A2 信号选择 using the switch on the control
panel.
Multi-function
analog input
(terminal A2) Select multi-function analog input
H3-09 function selec- 0 to 1F 0 No A A A A A 418H
function for terminal A2.
tion

端子 A2 设定

Gain (terminal Sets the input gain (level) when

A2) 10 V (20 mA) is input. 0.0 to 100.0
H3-10 Yes A A A A A 419H
Set according to the 100% value 1000.0 %
端子 A2 增益 for the function set for H3-09.

6-128
 Individual Functions

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Bias (terminal Sets the input gain (level) when 0 -100.0
A2) V (4 mA) is input. to
H3-11 0.0% Yes A A A A A 41AH
Set according to the 100% value +100.
端子 A2 偏置 for the function set for H3-09. 0
* The factory setting will change when the control method is changed. The flux vector factory setting is given.

Multi-function Contact Input Functions (H1-01 to H1-10)

Control Methods
Set- Open Open
ting Function V/f Loop Flux Loop
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
71 Speed/torque control change (ON: Torque control) No No No Yes Yes

78 Polarity Reverse Command for external torque reference No No No Yes Yes

Multi-function Contact Output Functions (H2-01 to H2-05)

Control Methods
Set- Open Open
ting Function V/f Loop Flux Loop
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
Speed control circuit operating for torque control (except when stopped).
32 The external torque reference will be limited if torque control is selected. No No No Yes Yes
Output when the motor is rotating at the speed limit.

Multi-function Analog Inputs (H3-05, H3-09)

Control Methods
Set- Open Open
ting Function V/f Loop Flux Loop
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
0 Add to terminal A1 Yes Yes Yes Yes Yes
13 Torque reference/torque limit at speed control No No No Yes Yes

14 Torque compensation No No No Yes Yes

Monitor Function
Name Control Methods
Con- Output Signal Level Open Open MEMO
Min. V/f Loop Flux Loop BUS
stant Description During Multi-Func- Unit Reg-
Number Display V/f with Vec- Vec- Vec-
tion Analog Output PG tor tor tor ister
1 2
Torque refer- Monitor in internal torque
ence 10 V: Motor rated torque 0.1
U1-09 reference value for vector No No A A A 48H
(-10 to 10 V possible) %
转矩指令 control.

6-129
 „Inputting Torque References and Torque Reference Directions
The torque reference can be changed according to an analog input by setting H3-09 (Multi-function analog
input terminal A2 selection) or H3-05 (Multi-function analog input terminal A3 selection) to 13 (torque refer-
ence) or 14 (torque compensation). The torque reference input methods are listed in the following table.

Torque Reference Input Selection

Reference Location Remarks
Method Method
Set H3-04 to 0 for a 0 to 10-V torque ref-
erence.
H3-04 = 1
Between A3 and AC To switch the torque reference between
H3-05 = 13
positive and negative torque, set a multi-
function analog input to 78.

Voltage input (-10 to 10 V) Set H3-08 to 0 for a 0 to 10-V torque ref-

erence.
Between A2 and AC To switch the torque reference between
H3-08 = 1
(Turn OFF pin 2 of positive and negative torque, set a multi-
H3-09 = 13
SW1.) function analog input to 78.
The input can be used for torque compen-
sation by setting H3-09 to 14.
To switch the torque reference between
Between A2 and AC positive and negative torque, set a multi-
H3-08 = 2
Current input (4 to 20 mA) (Turn ON pin 2 of function analog input to 78.
H3-09 = 13
SW1.) The input can be used for torque compen-
sation by setting H3-09 to 14.
F2-01 = 0
Option board (AI-14B) The input can be used for torque compen-
Between TC2 and TC4 H3-08 = 1
(-10 to 10 V) sation by setting H3-05 to 14.
H3-09 = 13
The direction of the torque output from the motor will be determined by the sign of the analog signal input. It
does not depend on the direction of the Run Command. The direction of torque will be as follows:
• Positive analog reference: Torque reference for forward motor rotation (counterclockwise as viewed from
the motor output axis).
• Negative analog reference: Torque reference for reverse motor rotation (clockwise as viewed from the
motor output axis).

Application Precautions
If the analog signal input level is 0 to 10 V or 4 to 20 mA, a forward torque reference will not be applied. To
apply reverse torque, use an input level of -10 V to 10 V or switch the direction using a multi-function input
set to 78 (polarity Reverse Command for external torque reference).

6-130
 Individual Functions

Torque compensation
from analog input

Torque reference Torque primary delay

from analog input filter d5-02

Speed limit from analog 1 Priority Internal torque

Torque limit
input from terminal A1 circuit reference
+ +
Speed controller + Refer to torque limit setting
(ASR)
− via constants and analog input
Speed limit
d5-04
2
d5-03

Speed limit bias

d5-05

Speed limiter
Speed feedback

Fig 6.68 Torque Control Block Diagram

„Speed Limiter and Priority Circuit (Speed Limit Function)

If the external torque reference and load are not balanced during torque control, the motor will accelerate in
either the forward or reverse direction. The speed limit function is used to limit the speed to a specified value
and it consists of the speed limiter circuit and priority circuit.
When the motor speed exceeds the speed limit value during torque control, the speed limiter circuit generates
the suppression torque proportional to the speed above the limit value and adds to the torque reference. The
priority circuit switches the internal torque reference to ASR output so that the motor speed does not exceed
the speed limit value.

Application Precautions
There are two ways to set a speed limit: using an input from an analog input terminal and setting a speed limit
in d5-04. The inputs methods for a speed limit are listed in the following table.

Location of Refer- Constant Set-

Speed Limit Input Method Remarks
ence tings
Set in d5-04 d5-03 = 2 -
Set H3-01 to 0 if the speed limit is always
b1-01 = 1
Between A1 and AC to be positive.
H3-01 = 1

Voltage input (-10 to 10 V) The value will be added to the value input
on A1 to determine the speed limit.
b1-01 = 0
Set H3-03 to 0 if the speed limit input on
Between A2 and AC H3-08 = 1
A2 is always to be positive.
H3-09 = 1
Turn OFF (V side) pin 2 of DIP switch S1
on the terminal board.
The value will be added to the value input
b1-01 = 0
on A1 to determine the speed limit.
Current input (4 to 20 mA) Between A2 and AC H3-08 = 2
Turn ON (I side) pin 2 of DIP switch S1
H3-09 = 1
on the terminal board.
If H3-09 is set to 0, the sum of the input
Option board (AI-4B) b1-01 = 3 between TC2 and TC4 will be added the
Between TC1 and TC4
(-10 to 10 V) F2-01 = 0 input between TC1 and TC4 to determine
the speed limit.

6-131
 The direction in which speed is controlled is determined by the sign of the speed limit signal and the direction
of the Run Command.
• Positive voltage applied: The speed in the forward direction will be limited for forward operation.
IMPORTANT • Negative voltage applied: The speed in the reverse direction will be limited for reverse operation.
If the direction of motor rotation and the command direction are not the same, speed will be limited to 0 as
long as b5-05 is set to 0.

„Setting Speed Limit Bias

The same speed limit bias can be set for the forward and reverse side, and is different from the speed limit. Set
d5-04 to 0, and set the speed limit bias (d5-05) as a percentage of the maximum output frequency.
When setting both forward and reverse speed limit biases to 50%, set the speed limit to 0 (d5-03 = 2, d5-04 =
0, d5-05 = 50). The torque control range with these settings is between -50 to +50% of the speed.
When using the speed limit together with the speed limit bias, the torque control range will be limited by the
speed limit + the speed limit biases on the forward and reverse sides of the speed limit range.
When the forward speed limit is set to 50% and the speed limit bias to 10%, the torque control range will be as
shown in the figure below unless the priority circuit is taken into consideration.

Forward torque

ΔN %

Reverse run Forward run

Forward speed limit

Speed limit bias d5-04 50 %
d5-05 10 %

ΔN will be set as follows

Torque reference [%]
At motoring operation:
C5-01

Reverse torque At regenerative operation: The smaller vaue

Torque reference [%]
or d5-05
C5-04

Fig 6.69 Setting Speed Limit Bias

„Torque Limit Operation Examples

Operation examples will be described separately for winding operation, in which the speed and motor torque
are in the same directions, and rewinding operation, in which the speed and motor torque are in opposite direc-
tions.

Winding Operation
In a winding operation, the line (speed) and torque generated by the motor are in the same direction. For the
winding operation, both the speed limit and the torque reference input are positive. The motor will accelerate
when the torque reference input is larger than the load and will decelerate when it is smaller than the load. If
the motor turns faster than the speed limit, a negative compensation value is output from the speed limiter cir-
cuit. When the speed then drops below the speed limit, a positive compensation value is output. The torque
compensation is proportional to the ASR proportional gain. When the sum of the torque reference and the
torque compensation output by the speed limiter is the same as the actual load, the motor will stop accelerating
and run at a constant speed.

6-132
 Individual Functions

Rewinding Operation
In a rewinding operation, the line (speed) and torque generated by the motor are in the opposite directions. (In
this example, we’ll assume that the line speed is positive and the torque reference input is negative.) For the
rewinding operation, the speed limit is positive and the torque reference input is negative. If the motor turns
faster than the speed limit, a negative compensation value is output from the speed limiter circuit. If the motor
is rotating in reverse, a negative compensation value is output. If the speed is 0 or is below the speed limit, a 0
compensation value is output. In this way, the output from the speed limiter is used to maintain the motor
speed between 0 and the speed limit. When the sum of the torque reference and the torque compensation out-
put by the speed limiter is the same as the actual load, the motor will stop accelerating and run at a constant
speed.
Winding Operation Rewinding Operation
Line direction N T N T Line direction
T N T N

X X X X
Configuration

Line direction Line

direction
M M M M

Normal Rotation
Forward Reverse Forward Reverse
Direction
Torque Reference
Polarity (TREF)
Speed Limit
Polarity (SLIM)
Torque Torque Torque
Torque Torque Torque
Torque Torque limit limit
limit ΔN limit
TREF
TREF
(d5-05) ΔN
(d5-05)
SLIM
SLIM
0 Speed
0 Speed
0 0 Speed SLIM
SLIM Speed ΔN
Generated Torque (d5-05) Torque (d5-05)
TREF TREF limit

Torque
Torque ǍN Torque
limit
limit limit

The lower value of ΔN(%) = The lower value of ΔN(%) =

TREF(%) TREF(%)
N(%) = N(%) = TREF(%) or d5-05(%) TREF(%) or d5-05(%)
C5-01 C5-01
C5-01 C5-01

„Rotation Direction Limit Operation Selection (Valid Only in Open-loop Vector 2 Con-
trol)
In applications where the machine is not rotated in the opposite direction to the sign of the speed limit (i.e., in
winding operation), use with d5-07 set to 1. If the sign of the calculated speed is the opposite to that of the
speed limit, a torque will be output to prevent the motor from accelerating in the opposite direction.

„Torque Reference Adjustment

Consider the following information when adjusting the torque.

Torque Reference Delay Time: d5-02

The time constant of the primary filter in the torque reference section can be adjusted. This constant is used to
eliminate noise in the torque reference signal and adjust the responsiveness to the host controller. Increase the
setting if oscillation occurs during torque control.

6-133
 Setting the Torque Compensation
Set multi-function analog input A2 or A3 to torque compensation (setting 14). When the amount of torque loss
for mechanical loss or other factor at the load is input to one of these terminals, it is added to the torque refer-
ence to compensate for the loss. The direction of torque will be as follows:
• Positive voltage (current): Torque compensation reference for forward motor rotation (counterclockwise as
viewed from the motor output axis).
• Negative voltage: Torque compensation reference for reverse motor rotation (clockwise as viewed from
the motor output axis).
Since the polarity of the voltage input determines the direction, only forward torque compensation can be
input when the 0 to 10 V or 4 to 20 mA signal level has been selected. If you want to input reverse torque com-
pensation, be sure to select the -10 to 10 V signal level.

„Speed/Torque Control Switching Function

It is possible to switch between speed control and torque control when one of the multi-function inputs (H1-01
to H1-10) is set to 71 (Speed/Torque Control Change). Speed control is performed when the input is OFF and
torque control is performed when the input is ON. Set d5-01 to switch speed/torque control.

6-134
 Individual Functions

„Setting the Speed/Torque Control Switching Timer

The delay between a change in the speed/control switching function input (ON to OFF or OFF to ON) and the
corresponding change in the control method can be set in d5-06. During the timer delay, the value of the 3 ana-
log inputs will retain the values they had when the ON/OFF status of speed/torque control switching signal
was changed. Use this delay to complete any changes required in external signals.

Application Precautions
• The frequency reference (during speed control) is set in b1-01. The speed limit during torque control is set
in d5-03.
• If the torque reference has been assigned to a multi-function analog input, terminal A2, or terminal A3, the
input function changes when the control method is switched between torque control and speed control.
During speed control: The multi-function analog input terminal is used as the torque limit input.
During torque control: The multi-function analog input terminal is used as the torque reference input.
• When the Run Command turns OFF, the control method when stopped will be for speed control. Even
from the torque control method, the system will automatically change to speed control and decelerate to a
stop when the Run Command turns OFF.
• When A1-02 (control method selection) is set to 3 (flux vector control), the speed/torque change command
(a setting of 71) can be set for a multi-function input (H1-01 to H1-10) to switch between speed and torque
control during operation. An example is shown below.

Terminal No. User Constant No. Factory Setting Setting Function

S8 H1-06 8 71 Speed/torque control change
Frequency reference selection
b1-01 1 1
A1 (terminals A1, A2)
d5-03 1 1 Speed limit (terminals A1, A2)
A3 H3-05 0 13 Torque reference/torque limit
A timing chart for switching between speed and torque control is shown in the following figure.

CLOSED CLOSED

OPEN OPEN
Speed/torque change signal
(terminal S8 input)
Run

Run Command Stop

Control mode Speed Torque Speed Torque Speed (decel to stop)

Speed limit Speed limit

Speed Speed
reference reference
Terminal A1 input
Torque limit Torque limit
Terminal A3 input
Torque Torque
reference reference

Fig 6.70 Speed/Torque Control Switching Time Chart.

6-135
 ‹ Speed Control (ASR) Structure
Speed control (ASR) during vector control adjusts the torque reference so that the deviation between the
speed reference and the estimated speed (PG feedback or speed estimator) is 0. Speed control (ASR) during V/
f control with a PG adjusts the output frequency so that the deviation between the speed reference and the esti-
mated speed (PG feedback or speed estimator) is 0. The following block diagram shows the structure of the
speed control for vector or V/f control with a PG.

Torque limits
C5-01, C5-03
+ + Torque reference
Frequency Primary
P filter
reference
− I +
I limit
C5-06
(C5-10) L7-01 to L7-04
Detected speed
C5-02, C5-04 C5-08
Estimated speed
Speed Control Block Diagram for Vector Control

+ Output frequency
Frequency
reference
+

Limit

+ +
− Change
Detected speed
rate
P
+
limiter
I
C5-01
C5-05
C5-03
C5-02, C5-04

Speed Control Block Diagram for V/f Control with a PG

Fig 6.71 Speed Control Block Diagrams

„Related Constants

Name Control Methods

Change Open Open MEMO
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera- Reg-
Number Display V/f with Vec- Vec- Vec-
tion PG tor tor tor ister
1 2
ASR propor-
tional (P) 0.00 to
Sets the proportional gain of the speed 20.00
C5-01 gain 1 300.00 Yes No A No A A 21BH
loop (ASR.) *1
*2
比例增益 1

ASR inte-
gral (I) time 0.000 0.500
Sets the integral time of the speed loop
C5-02 1 to Yes No A No A A 21CH
(ASR) in 1-second units.
10.000 s*1
积分时间 1

ASR propor-
tional (P) Usually setting is not necessary. 0.00 to
20.00
C5-03 gain 2 Set to change the rotational speed gain. 300.00 Yes No A No A A 21DH
*1
P, I *2
比例增益 2 P=C5-01
I=C5-02
ASR inte-
P=C5-03 0.000
gral (I) time I=C5-04 0.500
C5-04 2 to Yes No A No A A 21EH
0 E1-04 Motor speed (Hz) 10.000 s*1
积分时间 2

6-136
 Individual Functions

Name Control Methods

Change Open Open MEMO
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera- Reg-
Number Display V/f with Vec- Vec- Vec-
tion PG tor tor tor ister
1 2
ASR limit Sets the upper limit for the compensation
frequency for the speed control loop 0.0 to
C5-05 5.0% No No A No No No 21FH
ASR 极限 (ASR) to a percentage of the maximum 20.0
output frequency.

ASR pri- Sets the filter time constant for outputting

mary delay torque references from the speed control
time loop (ASR). It is set in 1-second units. 0.000
0.004s
C5-06 With open-loop vector 2 control, this set- to No No No No A A 220H
*1
ting is enabled only for speeds in the 0.500
ASR 延迟时间 range 0 to 35 Hz.
Usually setting is not necessary.

ASR switch-
Set the frequency for switching between
ing fre-
Proportion Gain 1, 2 and Integral Time 1,
quency 2 in Hz units. 0.0 to
C5-07 0.0 Hz No No No No A A 221H
Speed control (ASR) proportional gain 400.0
增益切换频率 switching for a multi-function input takes
priority.

ASR inte- Set the upper limit of the speed control

gral (I) limit 0 to
C5-08 loop integral as a percentage of the value 400% No No No No A A 222H
400
积分极限 at the rated load.

ASR pri- Sets the filter time constant for outputting

mary delay
torque references from the speed control
time 2 loop (ASR). It is set in 1-second units. 0.000
0.010
C5-10 With open-loop vector 2 control, this set- to No No No No No A 231H
s
ting is enabled only for speeds greater 0.500
ASR延迟时间2 than 35 Hz.
Usually setting is not necessary.
* 1. When the control method is changed, the factory settings will change. The flux vector factory settings are given.
* 2. The setting range for flux vector and open-loop vector 2 controls is 1.00 to 300.00.

Multi-function Contact Input Functions (H1-01 to H1-10)

Control Methods
Set- Open Open
ting Function V/f Loop Flux Loop
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
Speed control disable setting for V/f control with PG
D OFF: Use speed control V/f control with PG No Yes No No No
ON: Do not use speed control for V/f control with PG
Speed control integral reset
E No No No Yes Yes
Enables switching between PI and P control for the speed control loop.

Speed control (ASR) proportional gain switch (switching between C5-01 and C5-03)
77 OFF: Use proportional gain in C5-01 No No No Yes Yes
ON: Use proportional gain in C5-03

6-137
 „Speed Control (ASR) Gain Adjustment for Vector Control
Use the following procedure to adjust C5-01 and C5-03 with the mechanical system and actual load con-
nected.

At zero-speed, increase C5-01

(ASR P Gain 1) until there is no oscillation.

At zero-speed, decrease C5-02

(ASR I Time 1) until there is no oscillation.

Does oscillation develop when the motor

operates at the maximum normal operating YES Decrease C5-01 (ASR P Gain 1).
speed?

NO

Adjustment completed. Increase C5-02 (ASR I Time 1).

(When there is higher-level position control,
adjust the position loop gain so that
overshooting/undershooting doesn't occur.)

Fine Adjustments
When you want even finer gain adjustment, adjust the gain while observing the speed waveform. Constant set-
tings like those shown in the following table will be necessary to monitor the speed waveform.

Constant
Name Setting Explanation
No.
H4-01 Multi-function analog output 1 terminal FM monitor selection 2
Settings that allow multi-func-
H4-02 Multi-function analog output 1 terminal FM output gain 1.00 tion analog output 1 to be used
to monitor the output frequency.
H4-03 Multi-function analog output 1 terminal FM bias 0.0
H4-04 Multi-function analog output 2 terminal AM monitor selection 5
Settings that allow multi-func-
H4-05 Multi-function analog output 2 terminal AM output gain 1.00 tion analog output 2 to be used
to monitor the motor speed.
H4-06 Multi-function analog output 2 terminal AM bias selection 0.00
H4-07 Multi-function analog output 1 terminal signal level selection 1 Settings that allow a -10 to 10 V
H4-08 Multi-function analog output 2 terminal signal level selection 1 signal range to be monitored.

The multi-function analog outputs have the following functions with these constant settings.
• Multi-function analog output 1 (terminal FM): Outputs Inverter's output frequency (-10 to 10 V).
• Multi-function analog output 2 (terminal AM): Outputs actual motor speed (-10 to 10 V).
Terminal AC is the multi-function analog output common.
We recommend monitoring both the output frequency and the motor speed to monitor the response delay or
deviations from the reference value, as shown in the following diagram.

6-138
 Individual Functions

Adjusting ASR Proportional Gain 1 (C5-01)

This gain setting adjusts the responsiveness of the speed control (ASR). The responsiveness is increased when
this setting is increased. Usually this setting is higher for larger loads. Oscillation will occur if this setting is
increased too much.
The following diagram shows the type of changes that can occur in the response when the ASR proportional
gain is changed.

Motor speed

The proportional gain is high.

(Oscillation occurs when the gain is too high.)

The proportional gain is low.

Time

Fig 6.72 Responsiveness for Proportional Gain

Adjusting ASR Integral Time 1 (C5-02)

This constant sets the speed control (ASR) integral time.
Lengthening the integral time lowers the responsiveness, and weakens the resistance to external influences.
Oscillation will occur if this setting is too short. The following diagram shows the type of changes that can
occur in the response when the ASR integral time is changed.

Motor speed

Short integral time

Long integral time

Time

Fig 6.73 Responsiveness for Integral Time

6-139
 Different Gain Settings for Low-speed and High-speed
Switch between low-speed and high-speed gain when oscillation occurs because of resonance with the
mechanical system at low speed or high speed. The proportional gain P and integral time I can be switched
according to the motor speed, as shown below.

P = C5-01
P, I
I = C5-02

P = C5-03
I = C5-04 (Low speed)

Motor speed (Hz)

C5-07
If C5-07 is set to 0, P = C5-01 and I = C5-02.

Fig 6.74 Low-speed and High-speed Gain Settings

Setting the Gain Switching Frequency (C5-07)

Set the switching frequency to about 80% of the motor operating frequency or the frequency at which oscilla-
tion occurs.

Low-speed Gain Adjustments (C5-03, C5-04)

Connect the actual load and adjust these constants at zero-speed. Increase C5-03 (ASR proportional gain 2)
until there is no oscillation. Decrease C5-04 (ASR integral time 2) until there is no oscillation.

High-speed Gain Adjustments (C5-01, C5-02)

Adjust these constants at normal operating speed. Increase C5-01 (ASR proportional gain 1) until there is no
oscillation. Decrease C5-02 (ASR integral time 1) until there is no oscillation. Refer to Fine Adjustments on
page 6-138 for details on making fine adjustments of high-speed operation.

ASR Proportional Gain Switch Setting

When one of the multi-function inputs (H1-01 to H1-10) is set to 77, the input can be used to switch between
C5-01 (proportional gain 1) and C5-03 (proportional gain 2). Proportional gain 2 is used when the multi-func-
tion input is ON. This input has higher priority than the ASR switching frequency set in C5-07.

ON
ASR Gain Switch signal
(a multi-function input)
OFF

Proportional gain
Proportional gain (P)
determined
by motor speed.

C5-03 gain setting

C5-02 C5-02

The gain is changed linearly in integral time 1 (C5-02).

Fig 6.75 ASR Proportional Gain Switch

6-140
 Individual Functions

„Precautions for Open-loop Vector 2 Control

• The ASR primary delay time setting for open-loop vector 2 control is divided between constants C5-06
and C5-10. The constant that is used depends on the size of the operating frequency. If the operating fre-
quency is between 0 and 35 Hz, adjust the setting using C5-06, and if the operating frequency is greater
than 35 Hz, adjust the setting using C5-10.
• To increase the speed response, adjust the gain with reference to the explanations on page 4-19 in Chapter
4 Trial Operation.

„Gain Adjustment for Speed Control during V/f Control with PG

When using V/f control with PG, set the proportional gain (P) and the integral time (I) at E1-09 (minimum out-
put frequency) and E1-04 (maximum output frequency). Speed Control Gain Integral Time Adjustment for V/f
Control with PG shows how the proportional gain and integral time change in linear fashion based on the
speed.

P and I setting
P = C5-01
I = C5-02

P = C5-03
I = C5-04

Motor speed (Hz)

0 E1-09 E1-04
Min. output frequency Max. output frequency

Fig 6.76 Speed Control Gain Integral Time Adjustment for V/f Control with PG

Gain Adjustments at Minimum Output Frequency

Operate the motor at the minimum output frequency. Increase C5-03 (ASR proportional gain 2) to a level
where there is no oscillation. Decrease C5-04 (ASR integral time 2) to a level where there is no oscillation.
Monitor the Inverter's output current and verify that it is less than 50% of the Inverter rated current. If the out-
put current exceeds 50% of the Inverter's rated current, decrease C5-03 and increase C5-04.

Gain Adjustments at Maximum Output Frequency

Operate the motor at the maximum output frequency. Increase C5-01 (ASR proportional gain 1) to a level
where there is no oscillation. Decrease C5-02 (ASR integral time 1) to a level where there is no oscillation.

Fine Adjustments
When you want even finer gain adjustment, adjust the gain while observing the speed waveform. The adjust-
ment method is the same as that for vector control.
Enable integral operation during acceleration and deceleration (by setting F1-07 to 1) when you want the
motor speed to closely follow the frequency reference during acceleration and deceleration. Reduce the setting
of C5-01 if overshooting occurs during acceleration, and reduce the setting of C5-03 and increase the setting
of C5-04 if undershooting occurs when stopping. If overshooting and undershooting cannot be eliminated by
adjusting only the gain, reduce the value of C5-05 speed control and reduce the limit of the frequency refer-
ence compensation value.

6-141
 ‹ Increasing the Speed Reference Response (Feed Forward Control)
Use feed forward control to increase the responsiveness to speed references. This function is effective for
machines for which the ASR gain cannot be increased to a large value because doing so would result in vibra-
tions. There is also the additional effect of making the system less prone to overshoot. This function is valid
only in flux vector and open-loop vector 2 controls.
Overshooting when acceleration completed
is being suppressed

Overshooting
Rotation Rotation
speed speed
(min-1) (min-1)

Time(s) Time(s)
Feed forward control Conventional speed control

Overshooting control effect

Fig 6.77 Overshooting Control Effect

„Related Constants
Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Feed forward
control selec- Select the feed forward control.
0
N5-01 tion 0: Disabled 0 or 1 No No No No A A 5B0H
*1
1: Enabled
FF 控制选择

Motor accelera- Set the time required to acceler-

tion time ate the motor at the rated torque
(T100) to the rated speed (Nr).
J: GD2/4, P: Motor rated output 0.001 0.178
N5-02 2π x J [kgm2] x Nr [min-1]
to No No No No A A 5B1H
ta = [s]
10.000 s*2
60 x T100 [N x m]
电机加速时间
However,
60 P [kW]
T100 = x × 103 [N x m]
2π Nr [min-1]

Feed forward Set the proportional gain for feed

proportional forward control.
0.00 to
N5-03 gain Speed reference response will 1.0 No No No No A A 5B2H
100.00
increase as the setting of N5-03 is
前馈控制 P 增益 increased.
* 1. When the control method is changed, the factory setting will change. The flux vector factory setting is given.
* 2. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given.

6-142
 Individual Functions

„Feed Forward Control Structure

• The following block diagram shows the speed controller (ASR) and the feed forward control structure.
N5-02, N5-03 U1-45

Feed
Frequency Secondary
forward Torque limit
reference U1-44 current
controller
reference
Primary
Speed controller (ASR)
filter

C5-06
L7-01 to L7-04
(C5-10)
U1-05

Detected speed
(Calculated speed)

Fig 6.78 Structure of Speed Controller (ASR) and Feed Forward Control

„Setting Precautions
• When N5-02 (Motor acceleration time) is not properly set, the acceleration time may not increase. The fac-
tory setting of N5-02 depends on the Inverter capacity. When the Inverter capacity is different from the
motor capacity, calculate an appropriate acceleration time using the equation given in N5-02 of Chapter 5
User Constants or set the time that corresponds to the motor capacity referring to Factory Settings that
Change with the Control Method (A1-02) (Page 5-86)
• When setting the feed forward proportional gain (N5-03), take the inertia of the motor to be equivalent to
1. If the speed reference response is slow, increase the feed forward proportional gain (N5-03). If over-
shoot occurs with the actual speed, or if a negative torque reference is output when acceleration is com-
pleted, reduce the feed forward proportional gain (N5-03).
• When using the droop control function (i.e., if b7-01 is not set to 0.0), disable feed forward control (i.e., set
N5-01 to 0).

‹ Droop Control Function

Droop control is a function that allows the user to set the amount of motor slip.
When a single load is operated with two motors (such as in a crane conveyor), a high-resistance motor is nor-
mally used. This is to use torque characteristics that exhibit proportion movements due to changes in the sec-
ondary resistor to maintain torque balance with the load and overall speed balance with the load.
If droop control is used, a high-resistance motor characteristics can be set for a general-purpose motor.

The balance of the load is very different with different amounts of slip.

Torque Motor A's torque Torque Motor A's torque characteristics

characteristics
Motor B's torque characteristics

TA TA
Load torque Load torque
TB TB

Motor B's torque The difference between The difference between

characteristics TA and TB is getting larger. TA and TB is getting smaller.

Reference Speed Reference Speed

speed speed
Load balance when using a general-purpose motor Load balance when using a high-purpose motor

Fig 6.79 Droop Control Function

6-143
 „Related Constants
Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Droop control Sets the slip as a percentage of
gain maximum frequency when the
maximum output frequency is
specified and the rated torque 0.0 to
b7-01 0.0 Yes No No No A A 1CAH
occurs. 100.0
DROOP 增益 Droop-control is not performed
when the setting is 0.0.

Droop control Droop control responsiveness

delay time constant 0.03 to
b7-02 0.05 s No A A A A A 1CBH
When hunting or oscillation 2.00
DROOP 延时 occurs, increase the value.

„Setting Precautions
• Droop control is disabled if b7-01 is set to 0.0.
• Set b7-01 to the amount of slip as the percentage of slip when the maximum output frequency is input and
the rated torque is generated.
• Constant b7-02 is used to adjust the responsiveness of droop control. Increase this setting if oscillation or
hunting occur.
• Disable the feed forward control (N5-01 = 0) when using the droop control function.

„Setting the Droop Control Gain

Set the droop control gain as the speed reduction at a 100% motor torque, as a percentage of the maximum
output frequency.

Torque

b7-01

100%

Speed
0 Speed reference

Fig 6.80 Droop Control Gain

6-144
 Individual Functions

‹ Zero-servo Function
The zero-servo function holds the motor when the motor is stopped in what is call a zero-servo status. This
function can be used to stop the motor even with an external force acts on the motor or the analog reference
input is offset.
The zero-servo function is enabled when one of the multi-function inputs (H1-01 to H1-10) is set to 72 (zero-
servo command). If the zero-servo command is ON when the frequency (speed) reference falls below the zero-
speed level, a zero-servo status is implemented.

„Related Constants
Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Zero-speed Used to set the frequency which
level (DC injec- starts DC injection braking in
tion braking units of Hz when deceleration to
starting fre- stop is selected.
0.0 to
b2-01 quency) When b2-01 is less than E1-09, 0.5 Hz No A A A A A 189H
10.0
E1-09 becomes the DC injection
直流制动开始频
braking starting frequency.
率 (For flux vector control, zero-
speed control from B2-01)
Zero-servo gain Adjust the strength of the zero-
servo lock.
Enabled when the zero-servo
command is set for a multi-func-
tion input. When the zero-servo
command has been input and the
frequency reference drop below 0 to
b9-01 5 No No No No A No 1DAH
零伺服增益 excitation level (b2-01), a posi- 100
tion control loop is created and
the motor stops. Increasing the
zero-servo gain in turn increases
the strength of the lock. Increas-
ing it by too much will cause
oscillation.

Zero-servo Sets the output width of the P-

completion lock completion signal.
width Enabled when the “zero-servo
completion (end)” is set for a
multi-function input. The zero-
servo completion signal is ON
when the current position is
0 to
b9-02 within the range (the zero-servo 10 No No No No A No 1DBH
16383
position + zero-servo completion
零伺服结束
幅度 width.)
Set the allowable position dis-
placement from the zero-servo
position to 4 times the pulse rate
of the PG (pulse generator,
encoder) in use.

6-145
 Multi-function Contact Input Functions (H1-01 to H1-10)
Control Methods
Set- Open Open
ting Function V/f Loop Flux Loop
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
72 Zero-servo command (ON: Zero-servo) No No No Yes No

Multi-function Contact Output Functions (H2-01 to H2-05)

Control Methods
Set- Open Open
ting Function V/f Loop Flux Loop
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
Zero-servo end
33 No No No Yes No
ON: Current position is within zero-servo start position ± the zero-servo end width.

To output the zero-servo status externally, assign the Zero-servo End signal (setting 33) to one of the multi-
function outputs (H2-01 to H2-05).

Monitor Function
Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Zero-servo (Can-
movement Shows the number of PG pulses
not be
U1-35 pulses times 4 for the movement range 1 No No No A No 62H
out-
when stopped at zero.
零伺服移动脉冲 put.)

„Time Chart
A time chart for the zero-servo function is given in Time Chart for Zero-servo.

ON OFF
Run Command

Zero servo command ON OFF

Frequency (speed) reference

Excitation level
b2-01

Motor speed

Zero Servo End signal Zero-servo status

Fig 6.81 Time Chart for Zero-servo

6-146
 Individual Functions

„Application Precautions
• Be sure to leave the Run Command input ON. If the Run Command is turned OFF, the output will be inter-
rupted and the zero-servo function will become ineffective.
• The holding force of the zero-servo is adjusted in b9-01. The holding force will increase if the value of the
setting is increased, but oscillation and hunting will occur if the setting is too large. Adjust b9-01 after
adjusting the speed control gain.
• The zero-servo detection width is set as the allowable position offset from the zero-servo start position. Set
4 times the number of pulses from the PG.
• The Zero-servo End signal will go OFF when the zero-servo command is turned OFF.

Do not lock the servo for extended periods of time at 100% when using the zero-servo function. Inverter
errors may result. Extended periods of servo lock can be achieved by ensuring that the current during the ser-
volock is 50% or less or by increasing the Inverter capacity.
IMPORTANT

6-147
 Digital Operator Functions
This section explains the Digital Operator functions.

‹ Setting Digital Operator Functions

You can set Digital Operator-related constants such as selecting the Digital Operator display, multi-function
selections, and copy functions.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Monitor selec- Sets the monitor item to be dis-
tion after power played when the power is turned
up on.
o1-02 1: Frequency reference 1 to 4 1 Yes A A A A A 501H
2: Output frequency
通电监视项目
选择 3: Output current
4: The monitor item set for o1-01
Frequency units Sets the units that will be set and
of reference set- displayed for the frequency refer-
ting and moni- ence and frequency monitor.
tor 0: 0.01 Hz units
1: 0.01% units (Maximum
output frequency is 100%)
2 to 39:
min−1 units (Sets the motor
poles.)
40 to 39999:
User desired display
Set the desired values for setting 0 to
o1-03 0 No A A A A A 502H
and display for the max. output 39999
frequency.
频率指令单位

Set 4-digit number

excluding the decimal
point.
Set the number of digits
below the decimal point
to display.
Example: When the max. output
frequency value is 200.0, set
12000

Setting unit for

frequency con- Set the setting unit for frequency
stants related to reference-related constants.
o1-04 V/f characteris- 0: Hz 0 or 1 0 No No No No A A 503H
tics
1: min−1
参数设定单位

LOCAL/ Sets the Digital Operator Local/

REMOTE key Remote Key
enable/disable 0: Disabled
o2-01 0 or 1 1 No A A A A A 505H
1: Enabled (Switches between
L/R 键功能 the Digital Operator and the
constant settings.)

6-148
 Digital Operator Functions

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
STOP key dur- Sets the Stop Key in the run
ing control cir- mode.
cuit terminal 0: Disabled (When the Run
operation Command is issued from and
o2-02 0 or 1 1 No A A A A A 506H
external terminal, the Stop
Key is disabled.)
STOP 键 1: Enabled (Effective even
during run.)
User constant Clears or stores user initial values.
initial value 0: Stores/not set
1: Begins storing (Records the
set constants as user initial
values.)
o2-03 0 to 2 0 No A A A A A 507H
2: All clear (Clears all recorded
用户参数保存 user initial values)
When the set constants are
recorded as user initial values,
1110 will be set in A1-03.

Frequency ref- When the frequency reference is

erence setting set on the Digital Operator fre-
method selec- quency reference monitor, sets
tion whether the Enter Key is neces-
sary.
o2-05 0 or 1 0 No A A A A A 509H
0: Enter Key needed
1: Enter Key not needed
频率指令设定 When set to 1, the Inverter
accepts the frequency reference
without Enter Key operation.

Cumulative
operation time Sets the cumulative operation
setting time in hour units. 0 to
o2-07 0 hr No A A A A A 50BH
Operation time is calculated from 65535
累积运行时间设 the set values.
定

Fan operation Set the initial value of the fan

time setting operation time using time units. 0 to
o2-10 0 hr No A A A A A 50EH
风扇累积运行时
The operation time accumulates 65535
间 from the set value.

„Changing Frequency Reference and Display Units

Set the Digital Operator frequency reference and display units using constant o1-03. You can change the units
for the following constants using o1-03.
• U1-01 (Frequency Reference)
• U1-02 (Output Frequency)
• U1-05 (Motor Speed)
• U1-20 (Output Frequency after Soft Start)
• d1-01 to d1-17 (Frequency references)

„Switching Monitors when the Power Supply Is ON

Using constant o1-02, select the monitor item (U1-†† [status monitor]) to be displayed on the Digital Oper-
ator when the power supply is turned ON. For monitors that can be displayed, refer to U1-†† in Chapter 5
User Constants.

6-149
 Setting Precautions
If selecting monitor constants other than U1-01 (Frequency Reference), U1-02 (Output Frequency), and U1-
03 (Output Current), first select the monitor items to be displayed in o1-01, and then set o1-02 to 4.

„Disabling the STOP Key

If b1-02 (Operation Method Selection) is set to 1, 2, or 3, the Stop Command from the STOP Key on the Dig-
ital Operator is an emergency Stop Command.
Set o2-02 to 0 to disable emergency Stop Commands from the STOP Key on the Digital Operator.

„Disabling the LOCAL/REMOTE Key

Set o2-01 to 0 to disable the LOCAL/REMOTE Key on the Digital Operator. You cannot switch Inverter ref-
erence inputs set using reference inputs from the Digital Operator, b1-01 (Reference Selection), or b1-02
(Operation Method Selection).

„Initializing Changed Constant Values

You can save the Inverter constant set values that you have changed as constant initial values. Change the set
values from the Inverter factory settings, and then set o2-03 to 1.
If, however, “Out of Memory MAX Param Change” is displayed on the Operator when changes in the settings
of the constants are saved as initial values, do not attempt to register any further changes as initial values.
Set A1-03 (Initialize) to 1110 to initialize the Inverter constants using the user-set initial values in memory. To
clear the user-set initial values in memory, set o2-03 to 2.

„Setting the Frequency Reference using the UP and DOWN Keys without Using the
Enter Key
Use this function when inputting frequency references from the Digital Operator. When o2-05 is set to 1, you
can increment and decrement the frequency reference using the UP and DOWN Keys without using the Enter
Key.
For example, enter the Run Command using a 0 Hz reference, and then continuously press the UP Key to
increment the frequency reference by 0.01 Hz only for the first 0.5 s, and then by 0.01 Hz every 80 ms for 3 s
thereafter. Press and hold down the UP Key for 3 s minimum to reach the maximum output frequency 10 s
after that. The frequency reference that has been set will be stored in memory 5 s after the UP or DOWN Keys
are released.

„Clearing Cumulative Operation Time

Set the cumulative operation time initial value in time units in constant o2-07. Set o2-07 to 0 to clear U1-13
(Inverter Operating Time).

„Clearing Inverter Cooling Fan Operation Time

Set the fan operation time initial value in time units in constant o2-10. Set o2-10 to 0 to clear U1-40 (Cooling
Fan Operating Time).

6-150
 Digital Operator Functions

‹ Copying Constants
The Digital Operator can perform the following three functions using the built-in EEPROM (non-volatile
memory).
• Store Inverter constant set values in the Digital Operator (READ)
• Write constant set values stored in the Digital Operator to the Inverter (COPY)
• Compare constant set values stored in the Digital Operator with Inverter constants (VERIFY)

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Copy function 0: Normal operation
selection 1: READ (Inverter to Operator)
o3-01 0 to 3 0 No A A A A A 515H
2: COPY (Operator to Inverter)
拷贝功能选择 3: Verify (compare)

Read permitted
selection 0: Read prohibited
o3-02 0 or 1 0 No A A A A A 516H
1: Read permitted
读出许可选择

6-151
 „Storing Inverter Set Values in the Digital Operator (READ)
To store Inverter set values in the Digital Operator, make the settings using the following method.
Set 03-02 (Read permitted selection) to 1 (read permitted).

Table 6.1 READ Function Procedure

Step
Digital Operator Display Explanation
No.

1 Press the Menu Key, and select advanced programming mode.

* *

2 Press the DATA/ENTER Key, and select the constants monitor display.

Display o3-01 (Copy Function Selection) using the Increment Key and Decrement
3
Key.

4 Press the DATA/ENTER Key, and select the constants setting display.

5 Change the set value to 1 using the Increment Key.

6 Set the changed data using the DATA/ENTER Key. The READ function will start.

7 If the READ function ends normally, End is displayed on the Digital Operator.

8 The display returns to o3-01 when a key is pressed.

An error may occur while saving to memory. If an error is displayed, press any key to cancel the error display
and return to the o3-01 display.
Error displays and their meanings are shown below. (Refer to Chapter 7 Errors when Using the Digital Oper-
ator Copy Function.)
Error Display Meaning

You are attempting to set o3-01 to 1 while o3-02 is set to 0.

6-152
 Digital Operator Functions

Error Display Meaning

Read data length mismatch or read data error.

Tried to write constants to EEPROM on the Digital Operator, but unable to perform write
operation.

Select READ Permitted

Prevent overwriting the data stored in EEPROM in the Digital Operator by mistake. With o3-02 set to 0, if you
set o3-01 to 1, and perform the write operation, PrE will be displayed on the Digital Operator, and the write
operation will be stopped.

„Writing Constant Set Values Stored in the Digital Operator to the Inverter (COPY)
To write constant set values stored in the Digital Operator to the Inverter, make the settings using the follow-
ing method.

Table 6.2 COPY Function Procedure

Step
Digital Operator Display Explanation
No.

1 Press the MENU Key, and select advanced programming mode.

* *

2 Press the DATA/ENTER Key, and select the constants monitor display.

Display o3-01 (Copy Function Selection) using the Increment Key and Decrement
3
Key.

4 Press the DATA/ENTER Key, and select the constants setting display.

5 Change the set value to 2 using the Increment Key.

6 Set the changed data using the DATA/ENTER Key. The COPY function will start.

7 If the COPY function ends normally, End is displayed on the Digital Operator.

6-153
 Table 6.2 COPY Function Procedure(Continued)
Step
Digital Operator Display Explanation
No.

8 The display returns to o3-01 when a key is pressed.

During the copy operation, errors may occur. If an error is displayed, press any key to cancel the error display
and return to the 03-01 display.
Error displays and their meanings are shown below. (Refer to Chapter 7 Errors when Using Digital Operator
Copy Function.)
Error Display Meaning

Inverter product code and Inverter software number are different.

Inverter capacity with which you are trying to copy, and the Inverter capacity stored in
the Digital Operator are different.

The Inverter control method in which you are trying to copy, and the Inverter control
method stored in the Digital Operator are different.

Comparison between the constant written to the Inverter and the constant in the Digital
Operator shows they are different.

After copying has ended, comparison between the sum value of the Inverter constant area
and the sum value of the Digital Operator constant area shows they are different.

„Comparing Inverter Constants and Digital Operator Constant Set Values (VERIFY)
To compare Inverter constants and Digital Operator constant set values, make the settings using the following
method.

Table 6.3 VERIFY Function Procedure

Step
Digital Operator Display Explanation
No.

1 Press the MENU Key. and select advanced programming mode.

* *

2 Press the DATA/ENTER Key, and select the constants monitor display.

6-154
 Digital Operator Functions

Table 6.3 VERIFY Function Procedure (Continued)

Step
Digital Operator Display Explanation
No.

Display o3-01 (Copy Function Selection) using the Increment Key and Decrement
3
Key.

4 Press the DATA/ENTER Key, and select the function setting display.

5 Change the set value to 3 using the Increment Key.

Set the changed data using the DATA/ENTER Key. The VERIFY function will
6
start.

7 If the VERIFY function ends normally, End is displayed on the Digital Operator.

8 The display returns to o3-01 when a key is pressed.

An error may occur during the comparison. If an error is displayed, press any key to cancel the error display
and return to the o3-01 display. Error displays and their meanings are shown below. (Refer to Chapter 7
Errors when Using Digital Operator Copy Function.)
Error Display Meaning

Verify error (Settings in the Digital Operator and the Inverter do not match).

Inverter product code and Inverter software number are different.

„Application Precautions
• When using the copy function, check that the following settings are the same between the Inverter and the
Digital Operator.
• Inverter product and type • Inverter capacity and voltage
• Software number • Control method

• Use the copy function off-line or with a communications option board removed.
• A CPF03 fault (EEPROM error) can occur if the power is shut down while the Inverter constants are being
copied. Do not shut down the power while copying the constants.

6-155
 ‹ Prohibiting Writing Constants from the Digital Operator
If you set A1-01 to 0, you can refer to and set the A1 and A2 constant groups, and refer to drive mode, using
the Digital Operator.
If you set one of the constants H1-01 to H1-10 (multi-function contact input terminal S3 to S12 function selec-
tion) to 1B (write constants permitted), you can write constants from the digital operator when the terminal
that has been set is ON. When the set terminal is OFF, writing constants other than the frequency reference is
prohibited. You can, however, reference constants.

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Constant access Used to set the constant access
level level (set/read.)
0: Monitoring only (Monitoring
drive mode and setting A1-01
and A1-04.)
1: Used to select user constant
A1-01 (Only constants set in A2-01 0 to 2 2 Yes A A A A A 101H
参数的访问级 to A2-32 can be read and set.)
2: Advanced
(Constants can be read and set
in both quick programming
mode and advanced
programming (A) mode.)

‹ Setting a Password
When a password is set in A1-05, if the set values in A1-04 and A1-05 do not match, you cannot refer to or
change the settings of constants A1-01 to A1-03, or A2-01 to A2-32.
You can prohibit the setting and referencing of all constants except A1-00 by using the password function in
combination with setting A1-01 to 0 (Monitor only).

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Constant access Used to set the constant access
level level (set/read.)
0: Monitoring only (Monitoring
drive mode and setting A1-01
and A1-04.)
1: Used to select user constant
A1-01 (Only constants set in A2-01 0 to 2 2 Yes A A A A A 101H
参数的访问级 to A2-32 can be read and set.)
2: Advanced
(Constants can be read and set
in both quick programming
mode and advanced
programming (A) mode.)

6-156
 Digital Operator Functions

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Password Password input when a password
has been set in A1-05.
This function write-protects some
constants of the initialize mode.
0 to
A1-04 If the password is changed, A1-01 0 No A A A A A 104H
密码 9999
to A1-03 and A2-01 to A2-32
constants can no longer be
changed. (Programming mode
constants can be changed.)

Password set- Used to set a four digit number as

ting the password.
This constant is not usually dis-
played. When the Password (A1- 0 to
A1-05 0 No A A A A A 105H
04) is displayed, hold down the 9999
密码设定 RESET Key and press the Menu
Key and the password will be dis-
played.

„Setting Precautions
Constant A1-05 cannot be displayed using normal key operations. To display A1-05, hold down the RESET
Key and press the MENU Key while A1-04 is displayed.

‹ Displaying User-set Constants Only

You can set and refer to constants necessary to the Inverter only, using the A2 constants (user-set constants)
and A1-01 (Constants Access Level).
Set the number of the constant to which you want to refer in A2-01 to A2-32, and then set A1-01 to 1. You can
set and refer to constants set in A1-01 to A1-03 and A2-01 to A2-32 only, using advanced programming mode.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
User setting Used to set the constant numbers
constants that can be set/read. Maximum
32.
b1-01 106H
A2-01 to Effective when the Constant
to - No A A A A A to
A2-32 Access Level (A1-01) is set to
用户参数 o3-02 125H
User Program (1). Constants set
in constants A2-01 to A2-32 can
be set/read in programming mode.

6-157
 Options
This section explains the Inverter option functions.

‹ Performing Speed Control with PG

This section explains functions with V/f control with PG.

„Related Constants
Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
PG constant Sets the number of PG (pulse gen-
erator or encoder) pulses. 0 to
F1-01 600 No No Q No Q No 380H
PG 脉冲数 Sets the number of pulses per 60000
motor revolution.

Operation Sets the PG disconnection stop-

selection at PG ping method.
open circuit 0: Ramp to stop (Deceleration
(PGO) stop using Deceleration Time
1, C1-02.)
1: Coast to stop
F1-02 0 to 3 1 No No A No A No 381H
2: Fast stop (Emergency stop
using the deceleration time in
PG 动作选择 C1-09.)
3: Continue operation (To protect
the motor or machinery, do not
normally make this setting.)

Operation Sets the stopping method when an

selection at overspeed (OS) fault occurs.
overspeed (OS) 0: Ramp to stop (Deceleration
stop using Deceleration Time
1, C1-02.)
1: Coast to stop
F1-03 0 to 3 1 No No A No A A 382H
2: Fast stop (Emergency stop
OS 动作选择 using the deceleration time in
C1-09.)
3: Continue operation (To protect
the motor or machinery, do not
normally make this setting.)

Operation Sets the stopping method when a

selection at speed deviation (DEV) fault
deviation occurs.
0: Ramp to stop (Deceleration
stop using Deceleration Time
1, C1-02.)
F1-04 1: Coast to stop 0 to 3 3 No No A No A A 383H
2: Fast stop (Emergency stop
DEV 动作选择 using the deceleration time in
C1-09.)
3: Continue operation (DEV is
displayed and operation
continued.)

PG rotation 0: Phase A leads with Forward

Run Command. (Phase B
leads with Reverse Run Com-
mand.)
F1-05 0 or 1 0 No No A No A No 384H
PG 方向设定 1: Phase B leads with Forward
Run Command. (Phase A
leads with Reverse Run Com-
mand.)

6-158
 Options

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
PG division rate Sets the division ratio for the PG
(PG pulse mon- speed control board pulse output.
itor) Division ratio = (1+ n) /m (n=0 or
1 m=1 to 32)
F1-06 1 to
F1-06 1 No No A No A No 385H
n m 132
PG 输出分频比 This constant is only effective
when a PG-B2 is used.
The possible division ratio set-
tings are: 1/32 ≤ F1-06 ≤ 1.

Integral value Sets integral control during accel-

during accel/ eration/deceleration to either
decel enable/ enabled or disabled.
disable 0: Disabled (The integral
F1-07 function isn't used while 0 or 1 0 No No A No No No 386H
accelerating or decelerating; it
积分动作选择 is used at constant speeds.)
1: Enabled (The integral function
is used at all times.)

Overspeed
detection level Sets the overspeed detection 0 to
F1-08 115% No No A No A A 387H
method. 120
过速检出值 Frequencies above that set for F1-
Overspeed 08 (set as a percentage of the
maximum output frequency) that
detection delay
continue to exceed this frequency 0.0 to
F1-09 time 0.0 s* No No A No A A 388H
for the time set in F1-09 are 2.0
OS 过速检出 detected as overspeed faults.
时间

Excessive Sets the speed deviation detection

speed deviation method.
F1-10 detection level Any speed deviation above the 0 to 50 10% No No A No A A 389H
F1-10 set level (set as a percent-
DEV 检出值
age of the maximum output fre-
Excessive quency) that continues for the
speed deviation time set in F1-11 is detected as a
F1-11 detection delay speed deviation. 0.0 to
0.5 s No No A No A A 38AH
time Speed deviation is the difference 10.0
between actual motor speed and
DEV 检出时间 the reference command speed.

Number of PG Sets the number of teeth on the

F1-12 gear teeth 1 gears if there are gears between 0 No No A No No No 38BH
the PG and the motor.
PG 齿轮齿数 1
Input pulses from PG 60 F1-13 0 to
Number of PG 1000
F1-01 F1-12
gear teeth 2
F1-13 A gear ratio of 1 will be used if 0 No No A No No No 38CH
PG 齿轮齿数 2
either of these constants is set to
0.

PG open-cir- Used to set the PG disconnection

cuit detection detection time. PGO will be 0.0 to
F1-14 time 2.0 s No No A No A No 38DH
detected if the detection time con- 10.0
PGO 检出时间 tinues beyond the set time.

* When the control method is changed, the factory setting will change. The flux vector factory setting is given.

6-159
 „Using PG Speed Control Board
There are four types of PG Speed Control Board that can be used in V/f control with PG.
• PG-A2: A-phase (single) pulse input, compatible with open collector or complimentary outputs.
• PG-B2: A/B-phase pulse input, compatible with complimentary outputs.
• PG-D2: A-phase (single) pulse input, compatible with line drivers.
• PG-X2: A/B/Z-phase pulse input, compatible with line drivers.
There are two types of PG Speed Control Boards that can be used for flux vector control.
• PG-B2: A/B phase pulse inputs, complementary outputs
• PG-X2: A/B/Z phase pulse inputs, line driver outputs
For the connection diagram, refer to page 2-35 to 2-37.

„Setting Number of PG Pulses

Set the number of PG (Pulse Generator/Encoder) pulses in pulses/rotation. Set the number of A-phase or B-
phase pulses per 1 motor rotation in F1-01.

„Matching PG Rotation Direction and Motor Rotation Direction

Constant F1-05 matches the PG rotation direction and the motor rotation direction. If the motor is rotating for-
wards, set whether it is A-phase driven or B-phase driven. Make this setting when using PG-B2 or PG-X2.

Inverter
Motor PG (encoder)
Forward
Command

Pulse output
A-phase driven when set value = 0 B-phase driven when set value = 1

A-phase A-phase
B-phase B-phase

Example: Forward rotation of standard Yaskawa motor (PG used: Samtack (KK))

Motor output axis rotates

counter-clockwise during In-
Forward verter Forward Command.
Command Rotation
(CCW)
A-phase
B-phase

Yaskawa standard PG used is A-phase driven (CCW) when motor rotation is forward.

Fig 6.82 PG Rotation Direction Setting

Generally, PG is A-phase driven when rotation is clockwise (CW) see from the input axis. Also, motor rota-
tion is counter-clockwise (CCW) seen from the output side when Forward Commands are output. Conse-
quently, when motor rotation is forward, PG is normally A-phase driven when a load is applied, and B-phase
driven when a load is not applied.

6-160
 Options

„Setting Number of Gear Teeth Between PG and Motor

Set the number of PG gear teeth in F1-12 and F1-13. If there are gears between the motor and PG, you can
operate the motor by setting the number of gear teeth.
When the number of gear teeth has been set, the speed of motor rotations within the Inverter is calculated
using the following formula.

Speed of motor rotations (min−1.) = No. of input pulses from PG × 60 / F1-01 × F1-13 (No. of gear teeth on
load side) / F1-12 (No. of gear teeth on motor side)

„Matching Motor Speed During Acceleration and Deceleration to Frequency Reference

You can select whether to enable or disable integral operation during acceleration and deceleration when using
V/F with PG control.
To match the motor speed as closely as possible to the frequency reference even during acceleration and decel-
eration, set F1-07 to 1.

If F1-07 is set to 1, overshoot or undershoot may occur easily immediately after acceleration and decelera-
tion. To minimize the possibility of overshoot or undershoot occurring, set F1-07 to 0.

IMPORTANT

„Setting PG Pulse Monitor Output Dividing Ratio

This function is enabled only when using PG speed control board PG-B2. Set the dividing ratio for the PG
pulse monitor output. The set value is expressed as n for the higher place digit, and m for the lower place 2
digits. The dividing ratio is calculated as follows:
Dividing ratio = (1 + n)/m (Setting range) n: 0 or 1, m: 1 to 32
F1-06 = † ††
n m

The dividing ratio can be set within the following range: 1/32 ≤ F1-06 ≤ 1. For example, if the dividing ratio is
1/2 (set value 2), half of the number of pulses from the PG are monitor outputs.

„Detecting PG Open Circuit

Select the stopping method when PG cable disconnected is detected and the PG open circuit (PGO) detection
time.
When the Inverter is operating with the frequency reference set to 1% minimum (except when operating on
direct current), if the speed feedback from PG is greater than the time setting in F1-14, PGO is detected.

„Detecting Motor Overspeed

An error is detected when the number of motor rotations exceeds the regulated limit. An overspeed (OS) is
detected when a frequency that exceeds the set value in F1-08 continues for longer than the time set in F1-09.
After detecting an overspeed (OS), the Inverter stops according to the setting in F1-03.

„Detecting Speed Difference between the Motor and Speed Reference

An error is detected when the speed deviation (i.e., the difference between the designated speed and the actual
motor speed) is too great. Speed deviation (DEV) is detected after a speed agreement is detected and when the
speed reference and actual workpiece speed are within the setting of L4-02, if a speed deviation great than the
set value in F1-10 continues for longer than the time set in F1-11. After a speed deviation is detected, the
Inverter stops according to the setting in F1-04.

6-161
 ‹ Using Digital Output Boards
There are two types of Inverter digital output boards:
• DO-02C
Relay contact output (DPDT contact)
• DO-08
6 photocoupler output channels (shared commons)
2 (independent) relay contact output channels (NC contact)

Photocoupler TD5
CH1 Photocoupler
+24 V TD6
Inverter CH2
TD
1 control TD7
Inverter panel 3CN 3CN CH3
control NC NO 2
CH1
panel 3CN 3 TD8 CH4
3CN
4 TD9 CH5
NC NO 5
CH2 TD10 CH6
6 TD11 COM (0 V common)
TD1
Relay contact TD2 CH7
TD3 Relay contact
DO-02C Digital Output Card TD4 CH8

DO-08 Digital Output Card

Fig 6.83 Digital Output Boards

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Channel 1 out- Effective when a Digital Output
put selection Board (DO-02C or DO-08) is
F5-01 used. 0 to 37 0 No A A A A A 399H
DO CH1 选择 Set the number of the multi-func-
tion output to be output.

Channel 2 out- Effective when a Digital Output

put selection Board (DO-02C or DO-08) is
F5-02 used. 0 to 37 1 No A A A A A 39AH
DO CH2 选择 Set the number of the multi-func-
tion output to be output.
Channel 3 out- Effective when a DO-08 Digital
put selection Output Board is used.
F5-03 0 to 37 2 No A A A A A 39BH
Set the number of the multi-func-
DO CH3 选择 tion output to be output.

Channel 4 out- Effective when a DO-08 Digital

put selection Output Board is used.
F5-04 0 to 37 4 No A A A A A 39CH
Set the number of the multi-func-
DO CH4 选择 tion output to be output.

Channel 5 out- Effective when a DO-08 Digital

put selection Output Board is used.
F5-05 0 to 37 6 No A A A A A 39DH
Set the number of the multi-func-
DO CH5 选择 tion output to be output.
Channel 6 out- Effective when a DO-08 Digital
put selection Output Board is used.
F5-06 0 to 37 37 No A A A A A 39EH
Set the number of the multi-func-
DO CH6 选择 tion output to be output.

6-162
 Options

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Channel 7 out- Effective when a DO-08 Digital
put selection Output Board is used.
F5-07 Set the number of the multi-func- 0 to 37 0F No A A A A A 39FH
DO CH7 选择 tion output to be output.

Channel 8 out- Effective when a DO-08 Digital

put selection Output Board is used.
F5-08 0 to 37 0F No A A A A A 3A0H
Set the number of the multi-func-
DO CH8 选择 tion output to be output.

DO-08 output Effective when a DO-08 Digital

mode selection Output Board is used.
Set the output mode.
F5-09 0: 8-channel individual outputs 0 to 2 0 No A A A A A 3A1H
DO-08 选择 1: Binary code output
2: Output according to
F5-01 to F5-08 settings.

„Setting Output Items for the DO-02C Digital Output Board

If using DO-02C Digital Output Board, set the output items using F5-01 and F5-02.

„Setting Output Items for the DO-08 Digital Output Board

If using DO-08 Digital Output Board, select one of the following three output modes according to the setting
in F5-09.

F5-09 Set to 0
Terminal
Set Value Output Details
Number
TD5-TD11 Overcurrent (SC, OC, GF)
TD6-TD11 Overvoltage (OV)
TD7-TD11 Inverter overload (OL2)

0: 8 separate TD8-TD11 Fuse blown (PUF)

outputs TD9-TD11 Overspeed (OS)
TD10-TD11 Inverter overheated (OH1) or motor overload (OL1)
TD1-TD2 Zero-speed detected
TD3-TD4 Speed agreement

6-163
 F5-09 Set to 1
Terminal
Set Value Output Details
Number
TD5-TD11 bit 0

TD6-TD11 bit 1 Encoded output

(Refer to table below)
TD7-TD11 bit 2

1: Binary code TD8-TD11 bit 3

output TD9-TD11 Zero-speed detected
TD10-TD11 Speed agreement
TD1-TD2 Operating
TD3-TD4 Minor fault

The following table shows the code outputs.

Bits 3, 2, 1, Bits 3, 2, 1,
Output Details Output Details
and 0 and 0
0000 No error 1000 External fault (EFxx)
0001 Overcurrent (SC, OC, GF) 1001 Controller error (CPFxx)
0010 Overvoltage (OV) 1010 Motor overload (OL1)
0011 Inverter overload (OL2) 1011 Not used
0100 Inverter overheated (OH, OH1) 1100 Power loss (UV1, UV2, or UV3)
0101 Overspeed (OS) 1101 Speed deviation (DEV)
0110 Fuse blown (PUF) 1110 PG open circuit (PGO)
Dynamic braking resistor (RH)
0111 1111 Not used
Injection brake transistor error (RR)

F5-09 Set to 2
Output depends on the settings in F5-01 to F5-08.

‹ Using an Analog Reference Board

AI-14B provides 3 channels of bi-polar inputs with 14-bit A/D conversion accuracy (and a sign bit). The func-
tion of each channel is determined by the setting of F2-01.
AI-14U provides 2 channels of bi-polar inputs with 14-bit A/D conversion accuracy. Channel 1 is a voltage
input and channel 2 is a current input. The sum of channels 1 and 2 is a frequency input. F2-01 does not need
to be set for the AI-14U.

6-164
 Options

„Related Constants
Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Bi-polar or uni- Sets the functions for channel 1 to
polar input 3 that are effective when the AI-
selection 14B Analog Reference Board is
used.
0: 3-channel individual (Chan-
nel 1: terminal A1, Channel 2:
terminal A2, Channel 3: termi-
F2-01 nal A3) 0 or 1 0 No A A A A A 38FH
1: 3-channel addition (Addition
AI14 动作选择 values are the frequency refer-
ence)
When set to 0, select 1 for b1-01.
In this case the multi-function
input “Option/Inverter selection”
cannot be used.

„Setting Precautions
Always set b1-01 (Reference selection) to 1 (control circuit terminal) when using the AI-14B for three chan-
nels of independent inputs. When this is done, H1-01 to H1-10 (multi-function contact inputs) cannot be set to
2 (Option/Inverter selection).

‹ Using a Digital Reference Board

When using a DI-08 or DI-16H2 Digital Reference Board, set b1-01 (Reference selection) to 3 (Option board).
The DI-16H2 can be used to set a frequency using a 16-bit digital reference. The DI-08 can be used to set a
frequency using a 8-bit digital reference.

„Related Constants

Name Control Methods

Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Digital input Sets the Digital Reference Board
option input method.
0: BCD 1% unit
1: BCD 0.1% unit
2: BCD 0.01% unit
3: BCD 1 Hz unit
4: BCD 0.1 Hz unit
5: BCD 0.01 Hz unit
F3-01 6: BCD special setting (5-digit 0 to 7 0 No A A A A A 390H
DI 输入选择 input)
7: Binary input
6 is only effective when the DI-
16H2 is used.
When o1-03 is set to 2 or higher,
the input will be BCD, and the
units will change to the o1-03 set-
ting.

6-165
 Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Frequency units Sets the units that will be set and
of reference set- displayed for the frequency refer-
ting and moni- ence and frequency monitor.
tor 0: 0.01 Hz units
1: 0.01% units (Maximum
output frequency is 100%)
2 to 39:
min−1 units (Sets the motor
poles.)
40 to 39999:
User desired display
Set the desired values for setting 0 to
o1-03 0 No A A A A A 502H
and display for the max. output 39999
frequency.
频率指令单位

Set 4-digit number

excluding the decimal
point.
Set the number of digits
below the decimal point
to display.
Example: When the max. output
frequency value is 200.0, set
12000

„Selecting Input Terminal Functions for the DI-16H2 Digital Reference Board
The frequency reference from the DI-16H2 Board is determined by the setting of F3-01 and the 12/16-bit
switch on the option board. The possible settings are listed in the following table.

6-166
 Options

12-bit Binary 16-bit Binary 3-digit BCD with 4-digit BCD with 5-digit BCD with-
with Sign with Sign Sign Sign out Sign
Terminal Pin No.
F3-01 = 7 F3-01 = 7 F3-01 = 0 to 5 F3-01 = 0 to 5 F3-01 = 6
S1: 12 bit S1: 16 bit S1: 12 bit S1: 16 bit S1: 16 bit
1 Bit 1 (20) Bit 1 (20) 1 1 2
BCD digit 1
2 Bit 1 (21) Bit 1 (21) 2 BCD digit 1 2 BCD digit 1 4
(0, 2, 4, 6, 8)
(0 to 9) (0 to 9)
3 Bit 1 (22) Bit 1 (22) 4 4 8

4 Bit 1 (23) Bit 1 (23) 8 8 1

5 Bit 1 (24) Bit 1 (24) 1 1 2 BCD digit 2

TC1
(0 to 9)
6 Bit 1 (25) Bit 1 (2 )5 2 BCD digit 2 2 BCD digit 2 4
(0 to 9) (0 to 9)
7 Bit 1 (26) Bit 1 (26) 4 4 8

8 Bit 1 (27) Bit 1 (27) 8 8 1

9 Bit 1 (28) Bit 1 (28) 1 1 2 BCD digit 3

(0 to 9)
10 Bit 1 (29) Bit 1 (2 )9 2 BCD digit 3 2 BCD digit 3 4
(0 to 9) (0 to 9)
1 Bit 1 (210) Bit 1 (210) 4 4 8

2 Bit 1 (211) Bit 1 (211) 8 8 1

3 - Bit 1 (212) - 1 2 BCD digit 4

(0 to 9)
4 - Bit 1 (213) - 2 BCD digit 4 4
TC2 (0 to 9)
5 - Bit 1 (214) - 4 8

6 - Bit 1 (215) - 8 1 BCD digit 5

7 Sign signal (0: Forward, 1: Reverse) 2 (0 to 3)

8 SET (read) signal (1: Read)

9 Input signal common (0 V)
TC3 Shield wire connection terminal

„Application Precautions
• The maximum frequency (100% speed) reference will be used when the binary input is set (setting: 6 or 7)
and all bits are 1.
• Setting F3-01 to 6 is valid only when the D1-16H2 is used. Using this setting, a frequency from 0.00 to
399.8 Hz can be set in BCD. The sign bit is used as a data bit, so only positive (plus) data can be set. Also,
the digit starts from 0, so the minimum setting is 0.02 Hz.

„Selecting the Input Terminal Function for a DI-08 Digital Reference Board
The frequency reference from a DI-08 Board is determined by the setting of F3-01, as shown in the following
table.

6-167
 8-bit Binary with Sign 2-digit BCD with Sign
Terminal Pin No.
F3-01 = 7 F3-01 = 0 to 5
1 Bit 1 (20) 1

2 Bit 1 (21) 2 BCD digit 1

(0 to 9)
3 Bit 1 (22) 4

4 Bit 1 (23) 8

5 Bit 1 (24) 1
TC 6 Bit 1 (25) 2 BCD digit 2
7 6 4 (0 to 15)
Bit 1 (2 )

8 Bit 1 (27) 8

9 Sign signal
10 SET (read) signal
11 Reference common signal (0 V)

„Application Precautions
The DI-08 will not function if F3-01 is set to 6

„Selecting the Digital Reference

The range of the digital references is determined by the combination of the settings of o1-03 and F3-01. The
information monitored in U1-01 (Frequency reference) will also change.

DI-16H2 Reference Ranges

When using the DI-16H2, the following ranges can be set depending on the settings of the constants.

Switch Reference Setting U1-01 Monitor Unit

o1-03 F3-01 Reference Input Mode
S1 Range o1-03 = 0 o1-03 = 1
12 bits 3-digit BCD with sign, 1% -110 to 110%
0
16 bits 4-digit BCD with sign, 1% -110 to 110%
12 bits 3-digit BCD with sign, 0.1% -110.0 to 110.0%
1
16 bits 4-digit BCD with sign, 0.1% -110.0 to 110.0%
12 bits 3-digit BCD with sign, 0.01% -15.99 to 15.99%
2
16 bits 4-digit BCD with sign, 0.01% -110.0 to 110.0%
12 bits 3-digit BCD with sign, 1 Hz -400 to 400 Hz
3
0 or 1 16 bits 4-digit BCD with sign, 1 Hz -400 to 400 Hz 0.01 Hz 0.01%
12 bits 3-digit BCD with sign, 0.1 Hz -159.9 to 159.9 Hz
4
16 bits 4-digit BCD with sign, 0.1 Hz -400.0 to 400.0 Hz
12 bits 3-digit BCD with sign, 0.01 Hz -15.99 to 15.99 Hz
5
16 bits 4-digit BCD with sign, 0.01 Hz -159.99 to 159.99 Hz
6 16 bits 5-digit BCD without sign, 0.01 Hz 000.00 to 399.98 Hz
12 bits 12-bit binary with sign, 100%/4095 -4095 to 4095
7
16 bits 16-bit binary with sign, 100%/30000 -33000 to 33000

6-168
 Options

Switch Reference Setting U1-01 Monitor Unit

o1-03 F3-01 Reference Input Mode
S1 Range o1-03 = 0 o1-03 = 1
12 bits 3-digit BCD with sign, 1 rpm -1599 to 1599 rpm 1 rpm
2 to 39 -
16 bits 4-digit BCD with sign, 1 rpm -15999 to 15999 rpm 1 rpm
X0040 3-digit BCD with sign, 100%/(1- to 4-
- 12 bits -1599 to 1599
to digit setting of o1-03) 5th digit of o1-03 set-
X9999 ting:
(X = 0 4-digit BCD with sign, 100%/(1- to 4- -9999 to 9999
- 16 bits X = 0, unit: 1
to 3) digit setting of o1-03) (when o1-03 = 9999)
X = 1, unit: 0.1
X1000 X = 2, unit: 0.01
(X = 0 - 16 bits 4-digit BCD with sign, 100%/10000 -1000 to 1000 X = 3, unit: 0.001
to 3)

DI-08 Reference Ranges

When using the DI-08, the following ranges can be set depending on the settings of the constants.
U1-01 Monitor Unit
F3-01 Reference Input Mode Reference Setting Range
o1-03 = 0 o1-03 = 1
0 2-digit BCD with sign, 1% -110 to 110%
1 2-digit BCD with sign, 0.1% -15.9 to 15.9%
2 2-digit BCD with sign, 0.01% -1.59 to 1.59%
3 2-digit BCD with sign, 1 Hz -159 to 159 Hz
0.01 Hz 0.01%
4 2-digit BCD with sign, 0.1 Hz -15.9 to 15.9 Hz
5 2-digit BCD with sign, 0.01 Hz -1.59 to 1.59 Hz
6 -
7 8-bit binary with sign, 100%/255 -255 to 255

6-169
 Using Inverters for Elevating Machines
This section describes precautions to be observed when using the Varispeed G7 for elevating machines
such as elevators and cranes.

When performing trial operation, enable Current alarm function (L8-41 =1), and be sure to make adjustments
to the braking sequence by using Peak hold functions (refer to Current Alarm Function and Peak Hold Cur-
rent Monitoring Function in Chapter 6 ) so that the startup current is less than 150% of the Inverter rated cur-
IMPORTANT rent.

‹ Brake ON/OFF Sequence

„Brake ON/OFF Sequence

For the holding brake’s ON/OFF sequence, use the following Inverter output signals according to the set con-
trol method.
Brake ON/OFF Signal Brake ON/OFF Level Adjustment
Control Method
Signal Name Constant *1 Signal Name Constant

V/f (A1-02 = 0) Frequency detec- • Speed agree • L4-01 = 1.0 to

tion 2 H2-01 = 05*4
V/f with PG (A1-02 = 1) detection level 3.0 Hz *2
Open-loop vector 1 (A1-02 = 2, Frequency detec- • Speed agree • L4-02 = 0.1 to
factory setting) H2-01 = 36*4 detection width 0.5 Hz *3
tion 5
Zero-speed level b2-01 = 0.1 to
Flux vector (A1-02 = 3) During run 2 H2-01 = 37
(OFF timing only) 0.5 Hz

Do not set Open-loop vector 2 for use in elevating machines.

IMPORTANT

* 1. This example shows multi-function output terminals M1-M2 used for the holding brake ON/OFF signal.
Do not set H2-01 to 0 (During run).
* 2. This is the standard setting range for open-loop vector 1 control. For V/f control, set to approximately the motor rated slip frequency +0.5 Hz.
If the set value is too low, the motor torque is insufficient and the load may slip when the brake is applied. Be sure to set L4-01 to a value larger than that
of E1-09 (Min. output frequency) and larger than that of L4-02 shown in Figure 6.84. If the set value is too large, the motor may not run smoothly when
it starts running.
* 3. The hysteresis in frequency detection 2 can be adjusted (from 0.1 to 0.5 Hz) by L4-02 (speed agree detection width). Change the setting to approxi-
mately 0.1 Hz if there are drops while stopping.
* 4. When using frequency detection 2, set L4-01 before H2-01. If H2-01 is set before L4-01, the holding brake will engage while stopping. Normally, use
frequency detection 5 in which a holding brake signal is OFF when the Inverter is baseblocked.

L4-01
L4-02
Output frequency Time

ON OFF
Frequency detection 2

Fig 6.84

6-170
 Using Inverters for Elevating Machines

„Sequence Circuit Configuration

The brake ON/OFF sequence circuit configuration is shown below.

Inverter (Varispeed G7) Holding brake

Fault contacts auxiliary relay coil
MA
UP
S1 MB UP
(Forward run) Safety
BR
circuit DOWN
DOWN MC
S2
(Reverse run) BR
HIGH/LOW S6
(Multi-step speed reference 2) Energizes the brake when ON
M1 (250 VAC 1 A or less, 30 VDC
SC
1 A or less)
M2
Frequency
detection 2, 5 or
During run 2

Note Design the sequence so that the holding brake contact is open when the sequence operation conditions are satisfied and the contact between M1 and M2
is closed (ON).
Make sure that the holding brake contact is closed when the emergency stop signal or Inverter fault contact output signal is ON.
Fig 6.85 Brake ON/OFF Sequence Circuit Configuration

„Time Chart
The brake ON/OFF sequence time charts are shown in Figs. 6.86 and 6.87.

OFF ON
S1-SC UP
Input

High speed/ OFF ON

S6-SC
Low speed

d1-01 (Enabled when b1-01 = 0)

d1-03
Output frequency b4-01
L4-01
0
Output

Time
DC injection braking
Frequency detection 2
ON OFF
M1-M2 (H2-01 = 05)
Holding brake
operation CLOSE OPEN CLOSE

Note For variable speed operation by an analog signal, set to b1-01 = 1.

Fig 6.86 Brake ON/OFF Sequence Time Chart (V/f, V/f with PG, open-loop vector 1)

OFF ON
S1-SC UP
Input

S6-SC High speed/ OFF ON

Low speed

d1-01 (Enabled when b1-01 = 0)

d1-03
Output frequency b2-01
0 Time
Output

DC injection braking (Zero-speed control)

During run 2
M1-M2 (H2-01 = 37) ON OFF
Holding brake
operation CLOSE OPEN CLOSE

Note For variable speed operation by an analog signal, set to b1-01 = 1.

Fig 6.87 Brake ON/OFF Sequence Time Chart (Flux Vector)

6-171
 ‹ Stall Prevention during Deceleration
If connecting a braking resistor to discharge regenerative energy, be sure to set Stall prevention selection dur-
ing decel (L3-04) to 0 (Disabled).

If Stall prevention selection during decel (L3-04) is set to the initial value 1 (Enabled), the motor may not stop
within the specified decelerating time.
Stall prevention selection during accel (L3-01) and Stall prevention selection during running (L3-05) should be
IMPORTANT set to their initial values 1 (Enabled) to enable these functions.

‹ Autotuning
Always perform autotuning with the motor before operating using vector control. Be sure to disconnect the
motor from the load before conducting autotuning. Conducting autotuning while the motor is connected to an
elevating machine system is dangerous because it automatically runs the motor for approximately one minute.

1. When the motor cannot be disconnected from the load, perform stationary autotuning (T1-01 = 1 or 4).
Stationary autotuning will apply current to the motor in its stopped condition and automatically measure the
motor data. In the initial running period after autotuning (T1-01 =1) (20% speed min., fixed speed for 1 s
IMPORTANT min.), the motor data measured by autotuning will automatically be corrected.
2. To improve low-speed torque characteristics using V/f control, conduct stationary autotuning for line to line
resistance only (T1-01 = 2).
3. When conducting autotuning on wound motor or other special types of motors, obtain a test report for the
motor in advance and confirm that the E2 motor constants after autotuning do not vary greatly from those
of the test report.

‹ Braking Resistor Overheating Protection

When using a braking resistor other than the Braking Resistor Unit, provide a sequence with a thermal over-
load relay or similar means to turn off the power input to the Inverter when it detects resistor overheating. See
the Connection Diagram on page 2-3 for this sequence circuit.

‹ Momentary Power Loss Restart

Do not use the momentary power loss restart and fault restart functions in applications for elevating machines.
Make sure that L2-01=0 and L5-01=0. If these functions are used, the motor coasts to a stop with the brake
contact open when a momentary power loss or fault occurs during operation, possibly resulting in serious acci-
dents.

‹ Torque Limit
The torque limit values (L7-01 to L7-04) are the motor's rated torque. When there is a possibility of insuffi-
cient torque at start-up or other time, increase the Inverter capacity and set the torque limit value to between
200% and 300% (factory setting is 200%).

6-172
 Using Inverters for Elevating Machines

‹ I/O Open-phase Protection and Overtorque Detection

To prevent the machine from falling when the motor is open-phase or a similar situation, enable L8-05 and L8-
07 (Input and output open-phase protection selection) and L6-01 to L6-06 (Overtorque detection) (factory set-
ting is Disabled).
Falling detection or a similar safety measure should also be provided on the machine side.

‹ External Baseblock Signal

If the external baseblock command (settings 8 and 9 of H1-01 to H1-10) is input while the motor is running,
the motor will immediately coast to a stop. Do not input the external baseblock command while the motor is
running unless necessary.
Make sure that the holding brake operates when using the external base block command for an emergency
stop or interlock to start the Inverter.
If the external baseblock command is input and immediately reset, the Inverter does not output voltage during
the value of L2-03 (Min. baseblock time), which factory setting is 0.5 to 2.0 seconds depending on the Inverter
capacity. Do not use the external baseblock command in an application where the motor is frequently started
and stopped.

‹ Acceleration/Deceleration Time
If the delay time for the holding brake’s mechanical operation is not taken into consideration and the accelera-
tion/deceleration time on the Inverter side is set to a time that is too short, and overcurrent or wear on the
brakes may occur at staring or the load will slip at stopping because the holding brake does not operate on
time. If so, use the dwell function at start described on page 6-176 or the dwell function at stop described on
page 6-177 to tune the timing for the holding brake.

‹ Magnetic Contactor on the Inverter’s Output-side

Do not install a magnetic contactor between the Inverter and the motor. If a magnetic contactor must be
installed because of local electrical codes or regulations or to operate motors with an Inverter, excluding emer-
gencies, open or close the magnetic contactor only when the holding brake is fully closed and the Inverter is in
baseblock status with the baseblock signal ON.
If the magnetic contactor is opened or closed while the Inverter is controlling the motor or DC injection brak-
ing (Zero-speed control), surge voltage or a current from the motor by full-voltage starting may cause an
Inverter fault.
When a magnetic contactor is installed between the Inverter and the motor, set L8-07 (Output open-phase pro-
tection selection) to 1 or 2 (Enabled).

6-173
 ‹ Control-related Adjustments
The Varispeed G7 is designed to provide sufficient performance for elevating machines. However, if problems
related to controllability should occur, such as vibration or slipping, adjust the following constants in accor-
dance with the control method. Only constants that frequently require adjustment are listed in this table.

Table 6.4 Control-related Adjustments

Con- Recom-
Control Factory
stant Name Performance mended Adjustment Method
Method Setting
Number Setting
• Increasing torque and • Torque or speed response
Speed feed- speed response is insufficient: Reduce the
back detec- • Controlling hunting setting
N2-01 1.00 0.50 to 2.00
tion control and vibration in mid- • Hunting or vibration
(AFR) gain dle-range speeds (10 occurs: Increase the set-
to 40 Hz) ting

• Torque or speed response

Torque com-
• Increasing torque and is insufficient: Reduce the
pensation
speed response setting
C4-02 primary 20 ms 20 to 100 ms
• Controlling hunting • Hunting or vibration
delay time
and vibration occurs: Increase the set-
constant
ting

Slip compen- • Increasing speed • Speed response is slow:

sation pri- response 100 to Reduce the setting
C3-02 200 ms
mary delay • Improving speed sta- 500 ms • Speed is not stable:
Open-loop time bility Increase the setting
vector 1 con-
• Speed is slow: Increase
trol (A1-02 =
Slip compen- • Improving speed the setting
2) C3-01 1.0 0.5 to 1.5
sation gain accuracy • Speed is too fast: Reduce
the setting

• Reducing motor mag-

• Motor magnetic noise is
netic noise
Carrier fre- high: Increase the setting
• Controlling hunting
C6-02 quency *1 1 to F • Hunting or vibration
and vibration at low
selection occurs at low speeds:
speeds (10 Hz or
Reduce the setting
lower)

Mid. output 12.0 to

E1-08 frequency *2
• Improving torque and 11.0 V 13.0 V*2 • Torque or speed response
voltage (VC) speed response at low is insufficient: Increase
Min. output speeds the setting
frequency • Controlling shock at 2.0 to • Shock at startup is large:
E1-10 startup 2.0 V*2 Reduce the setting
voltage 3.0 V*2
(VMIN)

6-174
 Using Inverters for Elevating Machines

Table 6.4 Control-related Adjustments (Continued)

Con- Recom-
Control Factory
stant Name Performance mended Adjustment Method
Method Setting
Number Setting
ASR propor-
C5-01 tional (P) • Torque or speed response
• Increasing torque and
gain 1 is insufficient: Increase
speed response 10.00 to
20.00 the setting
ASR propor- • Controlling hunting 50.00
• Hunting or vibration
C5-03 tional (P) and vibration
occurs: Reduce the setting
gain 2

ASR inte- • Torque or speed response

C5-02 gral (I) time • Increasing torque and is insufficient: Reduce the
1 speed response 0.300 to setting
0.500 s
ASR inte- • Controlling hunting 1.000 s • Hunting or vibration
Flux vector
C5-04 gral (I) time and vibration occurs: Increase the set-
control
2 ting
(A1-02 = 3)
Set the output frequency at
which to change the ASR
Switching the ASR pro-
ASR switch- 0.0 to max. proportional gain and inte-
portional gain and inte- 0.0 Hz (no
C5-07 ing fre- output fre- gral time when the same val-
gral time according to switching)
quency quency ues cannot be used for both
the output frequency.
high-speed and low-speed
operation.

ASR pri- Machine rigidity is low and

• Controlling hunting 0.004 to
C5-06 mary delay 0.004 s the system vibrates easily:
and vibration 0.020
time Increase the setting

• Torque is insufficient for

• Controlling hunting heavy loads: Reduce the
Hunting-pre- and vibration in mid- setting
N1-02 1.00 0.50 to 2.00
vention gain dle-range speeds (10 • Hunting or vibration
to 40 Hz) occurs for light loads:
Increase the setting

• Motor magnetic noise is

• Reducing motor mag-
high: Increase the setting
Carrier fre- netic noise
• Hunting or vibration
C6-02 quency • Controlling hunting *1 1 to F
occurs at low to middle-
selection and vibration at low
range speeds: Reduce the
and medium speeds
setting
V/f control
(A1-02 = 0 • Improving torque at • Torque is insufficient at
or 1) low speeds (10 Hz or low speeds: Increase the
Torque com-
lower) setting
C4-01 pensation 1.00 0.50 to 1.50
• Controlling hunting • Hunting or vibration
gain
and vibration for light occurs for light loads:
loads Reduce the setting

Mid. output 13.0 to

E1-08 frequency 15.0 V*2 • Torque is insufficient at
voltage (VC) • Improving torque at 16.0 V*2
low speeds: Increase the
low speeds
Min. output • Controlling shock at setting
frequency 7.0 to • Shock at startup is large:
startup
E1-10 9.0 V*2 Reduce the setting
voltage 10.0 V*2
(VMIN)
* 1. Varies depending on capacity.
* 2. The setting is given for 200 V Class Inverters. Double the voltage for 400 V Class Inverters.
Note 1. Do not change C4-01 (Torque compensation gain) from its factory setting of 1.00 when using open-loop vector 1 control.
2. If speeds are inaccurate during regeneration in open-loop vector 1 control, enable Slip compensation selection during regeneration (C3-04 = 1). If
speeds are inaccurate in the high-speed range, enable Output voltage limit operation selection (C3-05 = 1).

6-175
 3. Do not use Slip compensation gain (C3-01) during V/f control (A1-02 = 0). (It is not used with the factory setting.)
4. Use the ASR constants (C5-01 to C5-05) in their factory settings when using V/f control with PG (A1-02 = 1). Vibration may occur if these constants
are changed greatly from their factory settings.
5. The torque and speed response of high-resistance (high-slip) motors are insufficient. Use appropriate adjustments to improve them. On the contrary,
low-resistance (low-slip) motors are easily subject to hunting and vibration. Here too, use appropriate adjustments to improve them.
6. The current during startup may increase when C4-02 (Torque compensation primary delay time constant) is increased. Check the current during star-
tup while adjusting this constant.

‹ Reducing Shock during Elevating Machine Start, Stop, Acceleration, and

Deceleration
When the riding comfort during start, stop, acceleration, and deceleration is of high importance, as it is for ele-
vators in which people ride, adjust the following constants.

„S-curve Characteristics, Acceleration/Deceleration Times

(High speed)
C2-02 C2-03
Output frequency (Low speed)
C2-03
C2-01 C2-04
C2-04

Acceleration time Deceleration time DC injection braking when stopping

(Zero-speed control for flux vector control)

1. The factory setting for C2-04 (S-curve characteristic time at deceleration end) is 0.00 second, while the fac-
tory setting for all other S-curve characteristic times is 0.20 second. Make appropriate settings for the
accel/decel times and S-curve characteristic times at each point. (S-curve characteristic time = Approxi-
IMPORTANT mately 0.2 to 1.0 second)
2. The accel/decel rate can be automatically switched during acceleration and deceleration by using C1-11
(Accel/decel time switching frequency). (Factory setting: Disabled)
Output frequency ≥ set frequency: C1-01, C1-02 accel/decel times
Output frequency < set frequency: C1-07, C1-08 accel/decel times
3. If the output frequency during the S-curve characteristic time for deceleration falls below the value set for
E1-09 (Min. output frequency), the S-curve characteristic will be cancelled, and the DC injection braking
(Zero-speed control) will be applied.
4. Do not use the S-curve characteristic for applications where a short run time is desired, such as in cranes
and hoists. (S-curve characteristic time = Approximately 0.0 to 0.2 second)

„Dwell Function at Start

b6-02
(High speed)
(Dwell time at start)
Output frequency 0.1 to 0.3 sec
b6-01 (Dwell frequency at start) 0.1 to 3.0 Hz
Frequency detection t
2 or During run 2 OFF ON
Holding brake
CLOSE OPEN
operation

6-176
 Using Inverters for Elevating Machines

If the mechanical operation of the holding brake is slow, use the dwell function at start to prevent brake wear,
and accelerate after the brake is completely open.

1. When using open-loop vector 1 control and V/f control, set b6-01 (Dwell frequency at start) higher than fre-
quency detection 2 (frequency when brakes open).
2. If the motor tends to have insufficient torque when started, use the DC injection braking function to allow
IMPORTANT sufficient motor current (torque) before starting.
• b2-03 (DC injection braking time at start): 0.2 to 0.5 s
• b2-02 (DC injection braking current): 50% to 80% (open-loop vector 1 control, V/f control only)

„Stopping with DC Injection Braking and Zero-speed Control

(HIGH) b2-04 (DC injection braking time at stop

(zero-speed control time at stop): 0.3 to 0.5 s
Output frequency (LOW)
Frequency t b2-01 [Zero speed level (DC injection braking
detection 2 or starting frequency)]: 0.1 to 3.0 Hz
During run 2 ON OFF b2-02 (DC injection braking current): 50% to 80%
(open-loop vector control, V/f control only)
Holding brake operation OPEN CLOSE

When the holding brake’s mechanical operation is slow, use DC injection braking (zero-speed control for flux
vector control) until the brakes are fully closed to prevent the brakes from slipping when stopping.

1. When the load cannot be maintained sufficiently using DC injection braking with open-loop vector 1 control
and V/f control, use the dwell functions at stop.
• b6-03 (Dwell frequency at stop): Min. output frequency to 3.0 Hz.
IMPORTANT The value must be less than the frequency when frequency detection 2 is OFF (L4-01 - L4-02).
• b6-04 (Dwell time at stop): 0.3 to 0.5 s
[b2-04 (DC injection braking at stop): 0.0 s]
2. If the Inverter and motor must be isolated while stopping using a magnetic contactor, for example in an ele-
vator, fully close the holding brakes and isolate the Inverter during baseblock (during baseblock signal: ON)
as stipulated by law in the EU.
During motor control or DC injection braking (zero-speed control), an Inverter error may occur due to surge
voltage. When a magnetic contactor is used between the Inverter and motor, set L8-07 (Output open-
phase protection) to 1 (enabled).

„Torque Compensation (Flux Vector Control Only)

When flux vector control is used, the torque compensation signals corresponding to the load can be input from
the multi-function analog input terminals in advance to reduce shock, such as that caused by opening and clos-
ing holding brakes. The load size and motoring/regenerating status must be detected at the machine side in
advance. Check that polarity is correct. Incorrect polarity will increase the shock.

6-177
 Sequence Circuit Configuration
The following diagram shows the sequence circuit configuration for torque compensation.

UP
S1 (Forward run)
DOWN
S2 (Reverse run)
HIGH/LOW
S6 (Multi-step speed reference 2)

SC

(Using elevator control circuit) A3

Torque compensation signal H3-04 (multi-function analog input terminal A3 signal level)
−10 to +10 V AC = 1 (−10 to +10 V)
H3-05 (multi-function analog input terminal A3 function
selection) = 14 (torque compensation)
Use H3-06 and H3-07 for fine tuning.

Fig 6.88 Torque Compensation Sequence Circuit Configuration

Time Chart
• Lifting
The analog signals corresponding to the load size are input as torque compensation signals from before the
Inverter starts until operation stops. (Factory setting: 10 V/100% torque)
Positive polarity is input for motor loads and negative polarity is input for regenerative loads.
The following diagram shows the time chart for lifting.

UP (Forward) OFF
ON
HIGH/LOW OFF
ON
Torque compensation
signal: 0 Analog signals corresponding to load size (Motor load: Inputs positive polarity.)
Same as above (Regenerative load: Inputs negative polarity.)

Output frequency
Zero-speed control
0 t

Motor torque (Motor load)

0
(Regenerative load)

During run 2 ON OFF

Holding brake operation OPEN

CLOSE

Fig 6.89 Torque Compensation Time Chart (Lifting)

• Lowering
In the same way as for lifting, when the torque decreases, the analog signals corresponding to the load size are
input as torque compensation signals from before the Inverter starts until operation stops. (Factory setting: 10
V/100% torque)
Negative polarity is input for motor loads and positive polarity is input for regenerative loads.
The following diagram shows the time chart for lowering.

6-178
 Using Inverters for Elevating Machines

DOWN (Forward) OFF

ON
HIGH/LOW OFF
ON
Torque compensation Analog signals corresponding to load size (Regenerative load: Inputs positive polarity.)
signal: 0
Same as above (Motor load: Inputs negative polarity.)

0 t
Output frequency

Motor torque (Regenerative load)

0
(Motor load)

During run 2 ON OFF

Holding brake operation OPEN
CLOSE

Fig 6.90 Torque Compensation Time Chart (Lowering)

1. For either increasing or decreasing torque, externally maintain the torque compensation signals during
operation to prevent them from fluctuating. Fluctuation in compensation signals during operation may result
in vibration.
IMPORTANT 2. If reverse run is used for lifting and forward run is used for lowering, the torque compensation signal polar-
ity must be reversed.

„Analog Input Filter Time Constant

If noise enters the analog frequency reference during operation using analog frequency reference (b1-01 = 1),
and operation becomes rough, implement noise countermeasures and also set H3-12 (Analog input filter time
constant) to between 0.01 and 0.10 s.

‹ Confirming Startup Current and Reducing Carrier Frequency

When performing a trial operation, set L8-41 (Current Alarm) to 1 (Enabled) and check the motor current
using the peak hold current monitoring function (U1-83) of the Digital Operator or a clamp ammeter, with and
without a mechanical load. An extremely high current will flow if the motor torque at start is insufficient, or if
timing is not correct and the motor locks with the holding brake.
If a current exceeding 150% of the Inverter rated current flows, the IGBT in the Inverter will be subject to heat
stress, resulting in a shortened life span.
In this case, take measures such as retuning and reduction of the load to reduce the current to a value less than
150% of the Inverter rated current.
Unless low noise operation is required, reduce the Inverter carrier frequency to a value between 2 kHz and 2.5
kHz to reduce the influence of heat stress.

6-179
 ‹ Overvoltage Inhibit Function
Leave L3-11 (Overvoltage inhibit function selection) set to 0 (disabled). This function is used to prevent over-
voltage tripping when the braking resistor is not used with a regenerative load. When this function is enabled,
the torque reference on the regenerative side is automatically inhibited in the Inverter during regeneration.
Using this function in elevating machines is dangerous because the elevator may slip and fall.

Contact your Yaskawa representative for details on applications such as high-speed elevators (speed: 2 m/s or higher),
direct-drive elevators, or Inverters designed for cranes.

6-180
 Current Alarm Function

Current Alarm Function

This function displays a current alarm (HCA) on the Digital Operator and outputs a minor fault contact
signal* when the Inverter output current exceeds 150% (effective value) of the rated output current. Use
this function to check the current during trial operation for machines that increase Inverter output current,
such as elevating machines.

*To output a minor failure contact signal from a multi-function contact terminal, set H2- to 10 (Minor failure).

If a current alarm occurs frequently, reduce the Inverter load.

Use the peak hold current monitoring function (U1-83 and U1-84) when performing retuning to reduce
the Inverter output current to 150% of the rated output current. Refer to Chapter 4 Trial Operation for
details.

For applications where a high current flows because of frequent start and stop operations, such as cranes, set L8-41 to 1
(Enabled).
If a current alarm occurs frequently, take measures such as:
IMPORTANT
• Reducing the frequency of operation and loading.
• Adjusting open/close timing of holding brake.
• Increasing acceleration/deceleration time.
• Taking enough time to produce motor magnetic flux (As described below).

■Related Constants
Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Allows or restricts an alarm from
Current alarm being triggered when the relative
output current rises above 150%.
L8-41 0 or 1 1 No A A A A A 4F2H
0: Disabled.
1: Enabled (alarm will be
电流警告
output).

If load is applied to an induction motor at startup before motor magnetic flux has been produced (as when
acceleration starts while the motor is locked by a brake mechanism or acceleration is too sudden), a high start-
ing current may flow.
In this case, use the following functions and constants to accelerate the motor after the magnetic flux is pro-
duced.
Startup current can be reduced by producing motor magnetic flux.
• Magnetic flux compensation function (See related constants b2-02 and b2-08)
• Dwell function (See related constants b6-01 and b6-02)
• Initial excitation function (See the setting 60 of the multi-function contact input H1)
For flux loop vector control, a multi-function input terminal can be used for initial excitation by setting
H1- to 60.
• Field forcing function (See related constant d6-03)

6-181
 Peak Hold Current Monitoring Function
This function saves the peak value (effective value) of the Inverter output current and displays it on the
Digital Operator for monitoring (U1-83). The Inverter output frequency at the moment the peak current
value is saved can be also monitored (U1-84).

At trial operation, perform adjustments so that the Inverter output current is limited to 150% of the rated
current checking the constants U1-83 and U1-84 of this function.

The values of peak current and output frequency during peak hold will be cleared when the Inverter stops and then starts,
or when the power is turned OFF and then ON. They will be retained while being baseblocked (stopped).

IMPORTANT

■Related Status Monitoring Constants

Name Control Methods
Con- Output Signal Level Open Open MEMO-
Min. V/f Loop Flux Loop BUS
stant Description During Multi-Function Unit
Number Display V/f with Vec- Vec- Vec- Regis-
Analog Output PG tor tor tor ter
1 2
Peak hold Displays the peak value of the 10V: Inverter rated output
current 0.01
current during run. “Peak current
U1-83 A A A A A A 7CFH
峰值保持电
Hold” refers to the moment (-10 to 10V absolute value
*1
流 that the peak value is saved. output)

Output
frequency
during Displays the frequency value 0.01
10V: Max frequency
U1-84 peak hold when the output current Hz A A A A A 7D0H
(-10V to 10V)
reached its peak value. *2
峰值保持输
出频率

* 1. The minimum unit differs depending on the Inverter capacity. (0.01 A for Inverter of 0.4 kW to 7.5 kW, and 0.1 A for Inverter of 11 kW or more)
* 2. The setting unit can be selected in o1-03.

„Related Fault Tracing Constants

The peak hold values are saved in the fault trace memory when a fault occurs.
Name Control Methods
Output Signal
Con- Open Open MEMO-
Level During Min. V/f Loop Flux Loop BUS
stant Description Unit
Number Display Multi-Function V/f with Vec- Vec- Vec- Regis-
PG tor tor tor ter
Analog Output
1 2
Peak hold
current at Displays the peak hold current 0.01
U2-21 fault (Cannot be output.) A A A A A 7E6H
when the last fault occurred. A*
峰值保持电流

Peak hold
output Displays the frequency value at
frequency at the moment the current reached 0.01
U2-22 fault (Cannot be output.) A A A A A 7E7H
its peak value when the last fault Hz
峰值保持输出
occurred.
频率

* The minimum unit differs depending on the Inverter capacity. (0.01 A for Inverter of 0.4 kW to 7.5 kW, and 0.1 A for Inverter of 11 kW or more)

6-182
 Maintenance Timer Display Function

Maintenance Timer Display Function

This function indicates that the estimated performance life of the cooling fan and electrolytic capacitor
have been reached.

The maintenance time periods displayed in the monitors as a percentage to the total life are only an estimate, not an exact
prediction of actual performance life.
Use them as guidelines for replacement.
IMPORTANT

‹ Settings Required to Use Maintenance Timer Display Function

Set H2- to 2F to use a multi-function contact output for this function and display an alarm on the Digital
Operator (the constants U1-61 and U1-63).

„Multi-function Contact Outputs (H2-01 to H2-03)

The maintenance time period for the cooling fan or electrolytic capacitor can be output from the multi-func-
tion contact terminal by setting H2-†† to 2F. Minor faults will not be output.
Control Methods
Set- Open Open
ting Function V/f Loop Flux Loop
V/f with Vec- Vec- Vec-
Value PG tor tor tor
1 2
Maintenance Time
2F ON: The operation time of either the electrolytic capacitors or the cooling fan has Yes Yes Yes Yes Yes
reached the specified maintenance time.

Refer to Multi-function Contact Outputs: H2 in Chapter 5 User Constants for information on multi-function
contact outputs.

„Related Status Monitoring Constants

Name Control Methods
Change MEMO
Con- Open Open
Setting Factory during V/f Flux BUS
stant Description Range Setting Opera- Loop Loop Regis-
Number Display V/f with
Vector
Vec-
Vector
tion PG tor ter
1 2
Cooling fan (Can-
Monitors the total operating time
operating time not be 1
U1-40 of the cooling fan. The time can A A A A A A 67H
out- hr
风扇运行时间 be set in o2-10.
put.)

Electrolytic For maintenance purposes, this

capacitor main- timer shows the amount of time (Can-
tenance the electrolytic capacitors have not be
U1-61 1% A A A A A A 7CH
been operating. Capacitors should out-
电容维护时期 be replaced when the monitor put.)
reaches 100%.
Cooling fan This monitor displays the amount (Can-
maintenance of time the cooling fan has been not be
U1-63 1% A A A A A A 7EH
operating. Replace the cooling fan out-
冷却扇维护 when the display reads 100%. put.)

6-183
 „Related Alarm Displays
When setting a multi-function contact output H2-†† to 2F, the alarm is displayed on the Digital Operator as
shown below.

Display Meaning Probable causes Corrective Actions

Electrolytic Capacitor Main-
LT-C The electrolytic capacitors have
tenance Timer Reset constant o2-18 to “0%” after
(blinking) reached their estimated maintenance
Monitor U1-61 has reached replacing the electrolytic capacitors.
C Maintenance time period.
100%.

Cooling Fan Maintenance

LT-F Timer The cooling fan has reached its esti- Replace the cooling fan and set con-
(blinking)
Monitor U1-63 has reached mated maintenance time period. stant o2-10 to “0H”.
Fan Maintenance
100%.

‹ Settings Required After Replacement of Cooling Fan or Electrolytic

Capacitor
• Set o2-10 to 0 after replacing the cooling fan.
• Set o2-18 to 0 after replacing the electrolytic bus capacitor.
Refer to Chapter 8 Maintenance and Inspection for the replacement procedure.

„Related Constants
Name Control Methods
Change Open Open MEMO-
Con-
Setting Factory during V/f Loop Flux Loop BUS
stant Description Range Setting Opera-
Number Display V/f with Vec- Vec- Vec- Regis-
tion PG tor tor tor ter
1 2
Fan opera- Set the initial value of the fan
tion time set- operation time using time
ting 0 to
o2-10 units. 0 hr No A A A A A 50EH
65535
The operation time accumu-
风扇累积运行
时间 lates from the set value.

Capacitor Allows the user to set the

maintenance maintenance time for the
setting electrolytic capacitors (U1-
0 to
o2-18 61). The user can reset the 0% No A A A A A 51DH
150
accumulated operation time
电容维护设定 back to zero, or to some other
desired value.

6-184
 Troubleshooting
This chapter describes the fault displays and countermeasure for the Inverter and motor prob-
lems and countermeasures.

Protective and Diagnostic Functions ...........................7-2

Troubleshooting .........................................................7-24
 Protective and Diagnostic Functions
This section describes the alarm functions of the Inverter. The alarm functions include fault detection,
alarm detection, operation error detection, and autotuning error detection.

‹ Fault Detection
When the Inverter detects a fault, the fault contact output operates, and the Inverter output is shut OFF causing
the motor to coast to a stop. (The stopping method can be selected for some faults, and the selected stopping
method will be used with these faults.) A fault code is displayed on the Digital Operator.
When a fault has occurred, refer to the following table to identify and correct the cause of the fault.
Use one of the following methods to reset the fault before restarting the Inverter:
• Set a multi-function contact input (H1-01 to H1-05) to 14 (Fault Reset) and turn ON the fault reset signal.
• Press the RESET Key on the Digital Operator.
• Turn the main circuit power supply OFF and then ON again.

Table 7.1 Fault Displays and Processing

Display Meaning Probable Causes Corrective Actions
• A short-circuit or ground fault
occurred at the Inverter output. (A
short or ground fault can be caused
by motor burn damage, worn insu- Reset the fault after correcting its
lation, or a damaged cable.) cause.
• The load is too large or the accelera- Note) Before turning the power
tion/deceleration time is too short. ON again, make sure that no
• A special-purpose motor or motor short-circuit or ground fault
with a capacity too large for the occurs at the Inverter output.
Inverter is being used.
• A magnetic contactor was switched
Overcurrent at the Inverter output.
OC
The Inverter output current exceeded
输出 Fix the broken/disconnected wir-
the overcurrent detection level. (200% There is a break in the PG wiring.
过电流 ing.
of rated current)
The PG is wired incorrectly. Fix the wiring.

Power isn't being supplied to the PG. Supply power to the PG properly.

• Make sure that incorrect wiring

has not been done.
• A short-circuit between +V, −V, and
• Check the resistance and wir-
AC terminals occurred.
ing for the frequency setting
• Overload in the control circuit ter-
potentiometer, etc. (Check that
minal.
the current for terminals +V and
–V is 20 mA or less.)

Reset the fault after correcting its

A ground fault occurred at the Inverter cause.
output. (A ground fault can be caused Note) Before turning the power
by motor burn damage, worn insula- ON again, make sure that no
Ground Fault* tion, or a damaged cable.) short-circuit or ground fault
GF occurs at the Inverter output.
The ground fault current at the
输出接地 Inverter output exceeded approxi- • Make sure that incorrect wiring
故障 mately 50% of the Inverter rated out- has not been done.
put current. • A short-circuit between +V, −V, and
• Check the resistance and wir-
AC terminals occurred.
ing for the frequency setting
• Overload in the control circuit ter-
potentiometer, etc. (Check that
minal.
the current for terminals +V and
–V is 20 mA or less.)
* The ground fault here is one which occurs in the motor wiring while the motor is running. A ground fault may not be detected in the following cases.
y A ground fault with low resistance which occurs in motor cables or terminals.
y A ground fault occurs when the power is turned ON.

7-2
 Protective and Diagnostic Functions

Table 7.1 Fault Displays and Processing (Continued)

Display Meaning Probable Causes Corrective Actions
The output transistor has failed
because of a short-circuit or ground
fault at the Inverter output.
PUF Check whether there is a short-circuit
Fuse Blown between the following terminals. A Replace the Inverter after correct-
保险丝
The fuse in the main circuit is blown. short-circuit will damage the output ing the cause.
熔断
transistor:
B1 ( 3) ←→ U, V, W
←→ U, V, W

Increase the deceleration time or

connect a braking resistor (or
The deceleration time is too short and
Braking Resistor Unit). Alterna-
the regenerative energy from the
tively, enable (set to 1) the stall
motor is too large.
prevention selection during decel-
eration (L3-04).

Motor ground fault

Check the output cable, relay ter-
(Ground fault current flowed to the
minal, or motor terminal box and
capacitor in the control circuit of the
correct the cause of ground fault.
Inverter through the power supply.)
Main Circuit Overvoltage
• Use the speed search function.
The main circuit DC voltage exceeded
• Adjust the settings of the Speed
the overvoltage detection level.
OV Incorrect constant setting for speed search operating current (b3-02)
200 V Class: Approx. 410 V
主回路过 search and Speed search deceleration
400 V Class: Approx. 820 V
电压 (The speed search can be performed time (b3-03).
(E1-01 ≥ 400 V)
during momentary power loss recov- • Use the estimated speed search
Approx. 720 V
ery and auto restart after a fault.) function. (Perform stationary
(E1-01 < 400 V)
autotuning for line-to-line resis-
tance only.)

Improper PG cable connection Check to see if the PG cable is

(PG noise, PG disconnection) connected properly.

The regenerative energy when an In vector control, enable (set to 1)

overshoot occurs after acceleration is the overvoltage inhibit selection
completed is too large. (L3-11).

Decrease the voltage so it’s within

The power supply voltage is too high.
specifications.

• An open-phase occurred with the

input power supply.
Main Circuit Undervoltage
• A momentary power loss occurred.
The main circuit DC voltage is below
• The wiring terminals for the input
the Undervoltage Detection Level
power supply are loose. • Reset the fault after correcting
(L2-05).
• The voltage fluctuations in the input its cause.
200 V Class: Approx. 190 V
power supply are too large. • Improve the power supply envi-
UV1 400 V Class: Approx. 380 V
• A fault occurred in the surge pre- ronment. (Check to see if the
主回路欠 Main Circuit Magnetic Connector
vention circuit. correct power tap is selected.)
电压 Operation Failure
• The magnetic contactor in the con- • Improve the operating environ-
The magnetic connector stopped
trol circuit was released (Contact ment.
responding during Inverter operation.
failure in the auxiliary contact). • Replace the Inverter.
Applicable Inverter Capacities
• The contact of the magnetic contac-
200 V Class: 37 to 110 kW
tor in the control circuit was cor-
400 V Class: 75 to 300 kW
roded due to environmental dust or
gas.

7-3
 Table 7.1 Fault Displays and Processing (Continued)
Display Meaning Probable Causes Corrective Actions
• The wiring of the control power cir-
cuit is incorrect.
• A Backup Capacitor Unit for • Try turning the power supply
Momentary Power Loss is not off and on.
UV2 Control Power Fault
attached to a 200 V/400 V Class • Replace the Inverter if the fault
控制回路 The control power supply voltage
Inverter of 7.5 kW or less and the continues to occur.
欠电压 dropped.
value of the Momentary power loss • Attach a Backup Capacitor Unit
ridethru time (L2-02) factory setting for Momentary Power Loss.
has been changed to the larger
value.

Inrush Prevention Circuit Fault

A fault occurred in the surge preven-
• The magnetic contactor in the main • Try turning the power supply
UV3 tion circuit.
circuit failed. off and on.
冲击防止 The magnetic contactor did not
• The magnetic contactor excitation • Replace the Inverter if the fault
回路故障 respond for 10 s even though the mag-
coil is burned out. continues to occur.
netic contactor ON signal has been
output.

• An open-phase occurred in the input

Main Circuit Voltage Fault
power supply.
The main circuit DC voltage oscillates
• A momentary power loss occurred.
unusually (not when regenerating).
• The wiring terminals for the input
PF This fault is detected if a load is Reset the fault after correcting its
power supply are loose.
输入缺相 greater than approximately 80% of the cause.
• The voltage fluctuations in the input
maximum motor capacity.
power supply are too large.
This fault is detected when L8-05 is
• The voltage balance between phases
set to 1.
is bad.

• There is a broken wire in the output

cable.
Output Open-phase Reset the fault after correcting its
• There is a broken wire in the motor-
An open-phase occurred at the cause.
winding.
LF
Inverter output. • The output terminals are loose.
输出缺相
This fault is detected when L8-07 is
set to 1 or 2 The motor being used has a capacity
Check the motor and Inverter
less than 5% of the rated output cur-
capacity.
rent.

The ambient temperature is too high. Install a cooling unit.

Cooling Fin Overheating There is a heat source nearby. Remove the heat source.
The temperature of the Inverter's cool-
ing fins exceeded the setting in L8-02 Replace the cooling fan. (Contact
The Inverter's cooling fan has stopped.
or the overheat protection level. our sales representative.)
OH: The temperature exceeded the
• Make sure that incorrect wiring
setting in L8-02 (Stopping method can
OH has not been done.
be changed by L8-03.). • A short-circuit between +V, −V, and
（OH1） • Check the resistance and wir-
OH1: The temperature exceeded AC terminals occurred.
散热片 ing for the frequency setting
100°C (Stopping method: Coast to • Overload in the control circuit ter-
过热 potentiometer, etc. (Check that
stop). minal.
the current for terminals +V and
–V is 20 mA or less.)

Inverter's Cooling Fan Fault

(200 V Class: 7.5 kW or more, • The Inverter's cooling fan has • Replace the cooling fan. (Con-
400 V Class: 5.5 kW or more) stopped. tact our sales representative.)
This fault is detected when L8-32 is • The heatsink is clogged. • Clean the heatsink.
set to 1.

7-4
 Protective and Diagnostic Functions

Table 7.1 Fault Displays and Processing (Continued)

Display Meaning Probable Causes Corrective Actions
Inverter’s Cooling Fan Fault
An Inverter’s cooling fan fault was
FAN detected, and the Inverter-overload The Inverter continued running with
Replace the cooling fan. (Contact
内部风扇 protection was activated based on the an overload after the cooling fan
our sales representative.)
故障 internal electric thermal value. stopped.
This fault is detected when L8-32 is
set to 0.

Check the size of the load and the

length of the acceleration, deceler-
Motor Overheating Alarm ation, and cycle times.
OH3
The Inverter will stop or will continue
电机 过热 The motor has overheated.
to operate according to the setting of Check the V/f characteristics.
警告
L1-03.
Check the Motor Rated Current
(E2-01).

Check the size of the load and the

length of the acceleration, deceler-
OH4 Motor Overheating Fault ation, and cycle times.
电机 过热 The Inverter will stop according to the The motor has overheated.
Check the V/f characteristics.
警告 2 setting of L1-04.
Check the Motor Rated Current
(E2-01).

• Reduce the load, increase the

Installed Braking Resistor Over-
RH The deceleration time is too short and deceleration time, or reduce the
heating
制动电阻 the regenerative energy from the motor speed.
Braking resistor protection function
过热 motor is too large. • Change to a Braking Resistor
set in L8-01 has operated.
Unit.

• Try turning the power supply

RR Internal Braking Transistor Fault • The braking transistor is damaged.
off and on.
制动晶体 The braking transistor is not operating • The Inverter’s control circuits are
• Replace the Inverter if the fault
管故障 properly. faulty.
continues to occur.

7-5
 Table 7.1 Fault Displays and Processing (Continued)
Display Meaning Probable Causes Corrective Actions
The load is too heavy. The accelera- Check the size of the load and the
tion time, deceleration time, and cycle length of the acceleration, deceler-
time are too short. ation, and cycle times.

• Use the speed search function.

• Adjust the settings of the Speed
search operating current (b3-02)
The constant setting for speed search
and Speed search deceleration
is incorrect.
time (b3-03).
(Motor overload occurred due to
• Use the estimated speed search
motor hunting and vibration.)
function. (Perform stationary
autotuning for line-to-line resis-
tance only.)

• Motor overload occurred when run-

ning at low speed. (If a general-pur-
pose motor is used, motor overload
can occur when running at low • Check the size of the load.
speed even if running within the • Check the setting of L1-01.
rated current.) • Increase the frame size of the
Motor Overload
• Motor protection selection (L1-01) Inverter.
OL1 The motor overload protection func- is set to general-purpose motor pro-
电机过载 tion has operated based on the internal tection (1) when an Inverter duty
electronic thermal value. motor is used.

• Correct the PG wiring.

The directions of the motor and PG
• Correct the motor wiring.
are different. (Only in flux vector con-
• Change the setting of PG rota-
trol)
tion (F1-05).

The V/f characteristics voltage is too

Check the V/f characteristics.
high.

The Motor Rated Current (E2-01) is Check the Motor Rated Current
incorrect. (E2-01).

• Make sure that incorrect wiring

has not been done.
• A short-circuit between +V, −V, and
• Check the resistance and wir-
AC terminals occurred.
ing for the frequency setting
• Overload in the control circuit ter-
potentiometer, etc. (Check that
minal.
the current for terminals +V and
–V is 20 mA or less.)

7-6
 Protective and Diagnostic Functions

Table 7.1 Fault Displays and Processing (Continued)

Display Meaning Probable Causes Corrective Actions
The load is too heavy. The accelera- Check the size of the load and the
tion time, deceleration time and cycle length of the acceleration, deceler-
time are too short. ation, and cycle times.

• Use the speed search function.

• Adjust the settings of the Speed
search operating current (b3-02)
The constant setting for speed search
and Speed search deceleration
is incorrect.
time (b3-03).
(Motor overload occurred due to
• Use the estimated speed search
motor hunting and vibration.)
function. (Perform stationary
autotuning for line-to-line resis-
tance only.)

• Correct the PG wiring.

The directions of the motor and PG
• Correct the motor wiring.
are different. (Only in flux vector con-
Inverter Overload • Change the setting of PG rota-
OL2 trol)
The Inverter overload protection func- tion (F1-05).
变频器
tion has operated based on the internal
过载 The V/f characteristics voltage is too
electronic thermal value. Check the V/f characteristics.
high.

Replace the Inverter with one that

The Inverter capacity is too low.
has a larger capacity.

• Make sure that incorrect wiring

has not been done.
• A short-circuit between +V, −V, and
• Check the resistance and wir-
AC terminals occurred.
ing for the frequency setting
• Overload in the control circuit ter-
potentiometer, etc. (Check that
minal.
the current for terminals +V and
–V is 20 mA or less.)

• Reduce the load.

Inverter overload occurred when run- • Increase the frame size of the
ning at a low speed of 6 Hz or less. Inverter.
• Lower the carrier frequency.

• Make sure that the settings in

Overtorque Detected 1 L6-02 and L6-03 are appropri-
OL3
There has been a current greater than ate.
过转矩 -
the setting in L6-02 for longer than the • Check the mechanical system
检出 1
setting in L6-03. and correct the cause of the
overtorque.

• Make sure that the current set-

Overtorque Detected 2 ting in L6-05 and time setting in
OL4
There has been a current greater than L6-06 are appropriate.
过转矩 -
the setting in L6-05 for longer than the • Check the mechanical system
检出 2
setting in L6-06. and correct the cause of the
overtorque.

• Make sure the load is an inertial

load.
OL7 High-slip Braking OL
The inertia returned to the load is too • Set the system so that the decel-
高滑差制 The output frequency did not change
large. eration time that does not pro-
动过载 for longer than the time set in N3-04.
duce overvoltages is 120 s or
less.

7-7
 Table 7.1 Fault Displays and Processing (Continued)
Display Meaning Probable Causes Corrective Actions
• Make sure that the settings in
Undertorque Detected 1 L6-02 and L6-03 are appropri-
UL3
There has been a current less than the ate.
欠转矩 -
setting in L6-02 for longer than the • Check the mechanical system
检出 1
setting in L6-03. and correct the cause of the
overtorque.

• Make sure that the current set-

Undertorque Detected 2 ting in L6-05 and time setting in
UL4
There has been a current less than the L6-06 are appropriate.
欠转矩 -
setting in L6-05 for longer than the • Check the mechanical system
检出 2
setting in L6-06. and correct the cause of the
overtorque.

Overshooting/Undershooting are
Adjust the gain again.
occurring.
Overspeed
OS The speed has been greater than the Check the reference circuit and
The reference speed is too high.
电机过速 setting in F1-08 for longer than the reference gain.
setting in F1-09.
The settings in F1-08 and F1-09 aren't Check the settings in F1-08 and
appropriate. F1-09.

Fix the broken/disconnected wir-

There is a break in the PG wiring.
ing.

PGO PG Disconnection Detected The PG is wired incorrectly. Fix the wiring.

PG 回路 PG pulses were input when the
故障 Inverter was outputting a frequency. Power isn't being supplied to the PG. Supply power to the PG properly.

Check for open circuit when using

Brake is applied to the motor.
brake (motor).

The load is too heavy. Reduce the load.

The acceleration time and deceleration Lengthen the acceleration time

time are too short. and deceleration time.
Excessive Speed Deviation
DEV
The speed deviation has been greater The load is locked. Check the mechanical system.
电机速度
than the setting in F1-10 for longer
偏差过大 The settings in F1-10 and F1-11 aren't Check the settings in F1-10 and
than the setting in F1-11.
appropriate. F1-11.

Check for open circuit when using

Brake is applied to the motor.
brake (motor).

Control Fault
The torque limit was reached continu-
Motor constant settings are not cor- • Check the motor constants.
ously for 3 seconds or longer during a
rect. • Perform autotuning.
deceleration stop during open-loop
CF
vector 1 control.
控制故障
An error occurred in the speed estima-
tion calculation for open-loop vector 2 Refer to Corrective Actions for Control Faults (CF) on page 7-14.
control.

PID Feedback Reference Lost

The settings in b5-13 and b5-14 aren’t Check the settings in b5-13 and
A PID feedback reference loss was
appropriate. b5-14.
detected (b5-12 = 2) and the PID feed-
FBL
back input was less than b5-13 (PID
反馈丧失
feedback loss detection level) for
The wiring of the PID feedback circuit
longer than the time set in b5-14 (PID Fix the wiring.
is incorrect.
feedback loss detection time).

7-8
 Protective and Diagnostic Functions

Table 7.1 Fault Displays and Processing (Continued)

Display Meaning Probable Causes Corrective Actions
EFO Check the Communications
External Fault Input from Commu-
选件卡外 - Option Board and communica-
nications Option Board
部故障 tions signals.

EF3
端子 S3 External Fault (Input Terminal 3)
故障

EF4 External Fault (Input Terminal 4)

EF5 External Fault (Input Terminal 5)

EF6 External Fault (Input Terminal 6) • Reset external fault inputs to the
An “external fault” was input from a multi-function inputs.
EF7 External Fault (Input Terminal 7) multi-function input terminal. • Remove the cause of the exter-
nal fault.
EF8 External Fault (Input Terminal 8)

EF9 External Fault (Input Terminal 9)

EF10 External Fault (Input Terminal 10)

EF11 External Fault (Input Terminal 11)

EF12 External Fault (Input Terminal 12)

The torque limit is too small. Increase the limit.

SVE Zero-servo Fault
零伺服 The rotation position moved during The load torque is too large. Reduce the load torque.
故障 zero-servo operation.
- Check for signal noise.

Exceeded Allowable Number of

Speed Search Retrials
SER The speed search has been retried The settings in b3-17 and b3-18 aren’t Make sure that the settings in b3-
速度搜索 more than the number of times set in appropriate. 17 and b3-18 are appropriate.
故障 b3-19 (Number of speed search retri-
als).

Digital Operator Connection Fault

OPR The connection to the Digital Operator Check the connection to the Digi-
操作器连 -
was broken during operation for a Run tal Operator.
接不良 Command from the Digital Operator.

MEMOBUS Communications Error Check the communications

CE A normal reception was not possible devices and communications sig-
-
通信故障 for 2 s or longer after control data was nals.
received once.

Option Communications Error

Check the communications
BUS A communications error was detected
devices and communications sig-
选件卡通 during a Run Command or while set- -
nals.
信故障 ting a frequency reference from a
Communications Option Board.

Check the communications tim-

ing such as communications cycle.
SI-T Watchdog Error Synchronization error between master
E5 Refer to MECHATROLINK COM-
Consistency error of received control controller and Inverter for control
SI-T WDT MUNICATIONS INTERFACE
data data.
CARD INSTRUCTIONS
(TOBPC73060008) for details.

7-9
 Table 7.1 Fault Displays and Processing (Continued)
Display Meaning Probable Causes Corrective Actions
SI-F/G Communications Error
Detected
E-15 A communications error was detected
Check the communications sig-
SI-F/G when a Run Command or frequency -
nals.
故障 reference was set from an option
board and continuous operation was
set for the E-15 operation selection.

Disconnect and then reconnect the

E-10 Digital Operator connection is faulty.
SI-F/G Option Board CPU Failure Digital Operator.
SI-F/G SI-F/G Option Board operation failed.
芯片 Inverter control circuit is faulty. Replace the Inverter.

Digital Operator Communications The Digital Operator's connector isn't Disconnect the Digital Operator
Error 1 connected properly. and then connect it again.
Communications with the Digital
CPF00 Operator were not established within 5 The Inverter's control circuits are
seconds after the power was turned Replace the Inverter.
操作器 faulty.
故障 1 on.

Try turning the power supply off

-
CPU External RAM Fault and on again.

The control circuits were destroyed. Replace the Inverter.

Digital Operator Communications The Digital Operator isn't connected Disconnect the Digital Operator
Error 2 properly. and then connect it again.
CPF01 After communications were estab-
操作器 lished, there was a communications
故障 2 The Inverter's control circuits are
error with the Digital Operator for Replace the Inverter.
faulty.
more than 2 seconds.

Try turning the power supply off

CPF02 -
Baseblock Circuit Error and on again.
BB 回路
故障 The control circuit is damaged. Replace the Inverter.

Try turning the power supply off

-
and on again.
CPF03 The Inverter power supply was shut
EEPROM EEPROM Error Initialize the constant settings
off while writing data to the Inverter
故障 (A1-03).
constants.

The control circuit is damaged. Replace the Inverter.

Try turning the power supply off

-
and on again.

The control circuit is damaged. Replace the Inverter.

CPF04 • Make sure that incorrect wiring
内部 A/D1 CPU Internal A/D Converter Error has not been done.
故障 • A short-circuit between +V, −V, and
• Check the resistance and wir-
AC terminals occurred.
ing for the frequency setting
• Overload in the control circuit ter-
potentiometer, etc. (Check that
minal.
the current for terminals +V and
–V is 20 mA or less.)

7-10
 Protective and Diagnostic Functions

Table 7.1 Fault Displays and Processing (Continued)

Display Meaning Probable Causes Corrective Actions
Try turning the power supply off
-
and on again.

The control circuit is damaged. Replace the Inverter.

CPF05 • Make sure that incorrect wiring
外部 A/D2 CPU External A/D Converter Error has not been done.
故障 • A short-circuit between +V, −V, and
• Check the resistance and wir-
AC terminals occurred.
ing for the frequency setting
• Overload in the control circuit ter-
potentiometer, etc. (Check that
minal.
the current for terminals +V and
–V is 20 mA or less.)

The option board is not connected Turn off the power and insert the
CPF06 properly. board again.
选择卡连 Option Board Connection Error
接故障 Replace the option board or the
The Inverter or option board is faulty.
Inverter.

Try turning the power supply off

-
CPF07 ASIC Internal RAM Fault and on again.
RAM 故障
The control circuit is damaged. Replace the Inverter.

Try turning the power supply off

-
CPF08 Watchdog Timer Fault and on again.
WAT 故障
The control circuit is damaged. Replace the Inverter.

Try turning the power supply off

-
CPF09 CPU-ASIC Mutual Diagnosis Fault and on again.
CPU 故障
The control circuit is damaged. Replace the Inverter.

CPF10 ASIC Version Fault The Inverter control circuit is faulty Replace the Inverter.
ASIC 故障
The option board is not connected Turn off the power and insert the
CPF20 Communications Option Board A/ properly. board again.
选件卡 D Converter Error
故障 The option board's A/D converter is Replace the Communications
faulty. Option Board.

CPF21 Communications Option Board

选件卡自 Self Diagnostic Error
诊故障
Communications Option Board fault. Replace the option board.
CPF22 Communications Option Board
选件卡类 Model Code Error
型故障
Communications Option Board fault. Replace the option board.

• Use the copy function off-line.

CPF23 The copy function of the Digital Oper-
Communications Option Board • Use the copy function with an
选件卡互 ator was used during communications.
DPRAM Error option board removed.
诊故障
The option board is not connected Turn off the power and insert the
properly. board again.

7-11
 Table 7.1 Fault Displays and Processing (Continued)
Display Meaning Probable Causes Corrective Actions
Replace the main circuit capacitor.
A loss in capacity due to aging of the
(Consult your YASKAWA repre-
main circuit capacitor.
sentative.)

The Inverter parts are faulty. Replace the Inverter.

An open phase was detected for an Refer to LF (output open phase) in

output. this table.
Main Circuit Capacitor Neutral
Point Potential Error Check the set values for C6-03
VCF An excessive imbalance occurred in and C6-04. The maximum output
VCF the main circuit capacitor’s neutral Carrier frequency set value (C6-03, frequency that can be set for 400
point potential. C6-04) is unsuitable. V Class Inverters is restricted by
the carrier frequency setting.
Refer to page 6-45.

• Reduce the load.

In V/f or open-loop vector control, the
• Increase the acceleration time.
motor consecutively loses synchro-
• Check the settings for V/f con-
nism (the output current exceeds
trol.
200% of the Inverter rated current).
• Use larger capacity Inverter.

Operator Error (Internal RAM

OPERATOR Fault)
ERR RAM At power ON, an error was detected
CHECK ERR from the results of the internal RAM
Write/Read check.

Operator Error (CPU Internal ROM

OPERATOR Fault)
ERR ROM At power ON and during operation, an
CHECK ERR error was detected when the internal
ROM was checked.

Operator Error (Transmission Cir-

OPERATOR cuit Fault) ---
Replace the Operator.
ERR DATA During operation, send processing did
SEND ERR not complete within 500 ms continu-
ously at least 10 times.

Operator Error (Internal RAM

Fault)
OPERATOR During operation, an error was
ERR RAM detected when the display pattern for
CHECK ERR the character code 80 to 8F recorded
in the internal RAM was checked.

OPERATOR Operator Error (Watchdog Error)

ERR WATCH During operation, an error was
DOG ERR detected in the program execution.

7-12
 Protective and Diagnostic Functions

Table 7.2 Causes and Corrective Actions When the Digital Operator Goes Dark
Display Meaning Probable Causes Corrective Actions
• Make sure that incorrect wiring
has not been done.
• A short-circuit between +V, −V, and
• Check the resistance and wir-
AC terminals occurred.
ing for the frequency setting
• Overload in the control circuit ter-
potentiometer, etc. (Check that
minal.
the current for terminals +V and
–V is 20 mA or less.)

The short-circuit bar between +1 and

+2 terminals in the main circuit has Attach the short-circuit bar.
been removed.
• Check the wiring for the Brak-
ing Unit, including cables con-
P terminal and N terminal of the Brak-
操作器 There was a drop in control power nected to the Braking Unit and
ing Unit are connected in reverse.
熄灭 voltage. relay terminals.
• Replace the Inverter.

Charge indicator is lit:

• Replace the Digital Operator.
• Replace the board or the
Inverter.
Control power circuit failure
Charge indicator is not lit:
• Check the input power supply
voltage.
• Replace the Inverter.

Turn OFF the power, wait for 5

Malfunction occurred in the control
minutes, and turn ON the power
power circuit.
again.

7-13
 „Corrective Actions for Control Faults (CF)

CF occurs

Are the motor and No

Inverter connected Fix the wiring.
properly?

Yes
U1-50 = 01,02 Refer to Autotuning on page
Are the motor No Execute autotuning for the 4-9. Execute autotuning after
constants set
correctly? motor constants. the control method is
changed.
Yes
U1-50 = 00,01, Refer to Autotuning on page
Has autotuning been No 02,08 Execute autotuning for the 4-9. Execute autotuning
executed for line-to-line
resistance?
line-to-line resistance. after changing cables.
Yes
Increase the torque limit Refer to Torque Limits: L7
Are the torque limit settings (L7-01 Yes or torque reference until on page 5-64. In particular, if
to L7-04, analog input) or the torque
reference input too small? is it within the allowable the regenerative torque limit
range for the machine. has been reduced to prevent
No
overvoltages, set L3-11 to 1
U1-50 = 00 If deceleration stop is not and set the regenerative
Is the stopping No torque limit to a large value.
possible or unnecessary
method appropriate? for the machine, set b1-03
to 1 (coast to stop).
Yes
U1-50 = 02 · Input the operation reference Refer to Speed Search
Is an operation reference Yes after the motor stops. on page 6-64.
being input while the motor · Set b3-01 to 1 or 3 (speed
is coasting?
search enabled).
No
U1-50 = 04 Refer to Procedure for
Adjust the speed estimator's
What is the CF error integral time (N4-07) or Increasing the Speed
code (U1-50)?
proportional gain (N4-08). Response on page 4-21.

U1-50 = 08
If the machine rotates only in the
same direction as the sign of the
speed limit, set b1-10 to 1.

U1-50 = 10 · If the machine rotates only in the

same direction as the sign of the
speed limit (winding operation), set
d5-07 to 1.
· Ensure that the motor's speed is
not 0 or that it does not rotate in
the opposite direction.

U1-50 = 20
· If the machine rotates in the Refer to Speed/Torque
opposite direction to the sign of Control Switching Function
the speed limit (rewinding on page 6-134.
operation), set d5-07 to 0.
· Start with speed control and then
switch to torque control when the
Use in open loop vector 1 control. frequency exceeds 3 Hz.

Meaning of CR Error Codes

U1-50 Meaning

00 Stop error

01 Magnetic flux calculation error 1

02 Magnetic flux calculation error 2

04 Speed estimator gain adjustment fault

08 Low-speed regeneration fault

10 Zero-speed fault

20 Rotation direction limit fault

7-14
 Protective and Diagnostic Functions

‹ Alarm Detection
Alarms are detected as a type of Inverter protection function that do not operate the fault contact output. The
system will automatically returned to its original status once the cause of the alarm has been removed.
The Digital Operator display blinks and an alarm is sent from the multi-function outputs (H2-01 to H2-05) if
selected.
When an alarm occurs, take appropriate countermeasures according to the table below.

Table 7.3 Alarm Displays and Processing

Display Meaning Probable causes Corrective Actions
Check the sequence of the forward and
EF Forward/Reverse Run Commands
Reverse Run Commands.
（闪烁） Input Together
Since the rotational direction is
正反转 Both the forward and Reverse Run -
unknown, the motor will be deceler-
同时 Commands have been ON for more
ated to a stop when this minor fault
输入 than 0.5 s.
occurs.

Main Circuit Undervoltage

The following conditions occurred
when there was no Run signal.
UV • The main circuit DC voltage was
（闪烁） below the Undervoltage Detection See causes for UV1, UV2, and UV3 See corrective actions for UV1, UV2,
主回路 Level Setting (L2-05). faults in the previous table. and UV3 faults in the previous table.
欠电压 • The surge current limiting mag-
netic contactor opened.
• The control power supply voltage
when below the CUV level.

Main Circuit Overvoltage

OV The main circuit DC voltage exceeded
（闪烁） Decrease the voltage so it's within
the overvoltage detection level. The power supply voltage is too high.
主回路 specifications.
200 V Class: Approx. 410 V
过电压 400 V Class: Approx. 820 V

The ambient temperature is too high. Install a cooling unit.

There is a heat source nearby. Remove the heat source

Replace the cooling fan. (Contact your

OH The Inverter cooling fan has stopped.
Cooling Fin Overheating Yaskawa representative.)
（闪烁） The temperature of the Inverter's cool-
散热片 ing fins exceeded the setting in L8-02. • Make sure that incorrect wiring has
过热 • A short-circuit between +V, −V, and not been done.
AC terminals occurred. • Check the resistance and wiring for
• Overload in the control circuit ter- the frequency setting potentiometer,
minal. etc. (Check that the current for ter-
minals +V and –V is 20 mA or less.)

Inverter’s Cooling Fan Fault

FAN An Inverter’s cooling fan fault was
（闪烁） The Inverter’s cooling fan has Replace the cooling fan. (Contact our
detected.
内部风 stopped. sales representative.)
This fault is detected when L8-32 is
扇故障 set to 0.

Inverter Overheating Pre-alarm

OH2 An OH2 alarm signal (Inverter over-
Clear the multi-function input termi-
（闪烁） heating alarm signal) was input from a -
nal's overheating alarm input.
过热 2 multi-function input terminal (S3 to
S7).

7-15
 Table 7.3 Alarm Displays and Processing (Continued)
Display Meaning Probable causes Corrective Actions
Check the size of the load and the
length of the acceleration, decelera-
OH3 Motor Overheating tion, and cycle times.
（闪烁） E was set for H3-09 and the motor
The motor has overheated.
电机过 temperature thermistor input exceeded Check the V/f characteristics.
热警告 the alarm detection level.
Check the motor temperature input on
terminals A1 and A2.

OL3 Overtorque 1 • Make sure that the settings in L6-02

（闪烁） There has been a current greater than and L6-03 are appropriate.
-
过转矩 the setting in L6-02 for longer than the • Check the mechanical system and
检出 1 setting in L6-03. correct the cause of the overtorque.

• Make sure that the current setting in

OL4 Overtorque 2
L6-05 and time setting in L6-06 are
（闪烁） There has been a current greater than
- appropriate.
过转矩 the setting in L6-05 for longer than the
• Check the mechanical system and
检出 2 setting in L6-06.
correct the cause of the overtorque.

UL3 Undertorque 1 • Make sure that the settings in L6-02

（闪烁） There has been a current less than the and L6-03 are appropriate.
-
欠转矩 setting in L6-02 for longer than the • Check the mechanical system and
检出 1 setting in L6-03. correct the cause of the overtorque.

• Make sure that the current setting in

UL4 Undertorque 2
L6-05 and time setting in L6-06 are
（闪烁） There has been a current less than the
- appropriate.
欠转矩 setting in L6-05 for longer than the
• Check the mechanical system and
检出 2 setting in L6-06.
correct the cause of the overtorque.

Overshooting/undershooting are
Adjust the gain again.
occurring.
Overspeed
OS The speed has been greater than the Check the reference circuit and refer-
（闪烁） setting in F1-08 for longer than the The reference speed is too high.
ence gain.
过速 setting in F1-09.
The settings in F1-08 and F1-09 aren't
Check the settings in F1-08 and F1-09.
appropriate.

There is a break in the PG wiring. Fix the broken/disconnected wiring.

PGO The PG is Disconnected The PG is wired incorrectly. Fix the wiring.

（闪烁） The Inverter is outputting a frequency,
PG断线 but PG pulses aren't being input. Power isn't being supplied to the PG. Supply power to the PG properly.
检出
Check for open circuit when using
Brake is applied to the motor.
brake (motor).

The load is too large. Reduce the load.

The acceleration time and decelera- Lengthen the acceleration time and
DEV tion time are too short. deceleration time.
Excessive Speed Deviation
（闪烁） The speed deviation has been greater The load is locked. Check the mechanical system.
电机速 than the setting in F1-10 for longer
度偏差 than the setting in F1-11. The settings in F1-10 and F1-11 aren't
过大 Check the settings in F1-10 and F1-11.
appropriate.

Check for open circuit when using

Brake is applied to the motor.
brake (motor).

7-16
 Protective and Diagnostic Functions

Table 7.3 Alarm Displays and Processing (Continued)

Display Meaning Probable causes Corrective Actions
External Fault Detected for Com-
EF0 munications Board Other Than
（闪烁） SI-K2
选件卡 - Remove the cause of the external fault.
Continuing operation was specified
外部 for EF0 (F6-03 = 3)and an external
故障 fault was input from the option board.

EF3
（闪烁） External Fault (Input Terminal S3)
端子 S3
故障

EF4 External Fault (Input Terminal S4)

（闪烁）

EF5 External Fault (Input Terminal S5)

（闪烁）

EF6 External Fault (Input Terminal S6)

（闪烁）
• Reset external fault inputs to the
EF7 An external fault was input from a
External Fault (Input Terminal S7) multi-function inputs.
（闪烁） multi-function input terminal (S3 to
• Remove the cause of the external
S7).
fault.
EF8 External Fault (Input Terminal S8)
（闪烁）

EF9 External Fault (Input Terminal S9)

（闪烁）

EF10 External Fault (Input Terminal S10)

（闪烁）

EF11 External Fault (Input Terminal S11)

（闪烁）

EF12 External Fault (Input Terminal S12)

（闪烁）
PID Feedback Reference Lost The settings in b5-13 and b5-14 aren’t
Check the settings in b5-13 and b5-14.
A PID feedback reference loss was appropriate.
FBL detected (b5-12 = 2) and the PID feed-
（闪烁） back input was less than b5-13 (PID
反馈 feedback loss detection level) for The wiring of the PID feedback cir-
丧失 Fix the wiring.
longer than the time set in b5-14 (PID cuit is incorrect.
feedback loss detection time).

CE MEMOBUS Communications Error

（闪烁） Normal reception was not possible for Check the communications devices
-
通信 2 s or longer after received control and signals.
故障 data.

Option Board Communications

BUS Error
（闪烁） A communications error occurred in a Check the communications devices
选件卡 -
mode where the Run Command or a and signals.
通信 frequency reference is set from an
故障 Communications Option Board.

CALL
（闪烁） Communications on Standby Check the communications devices
SI-B Control data was not normally -
and signals.
通信 received when power was turned ON.
错误

7-17
 Table 7.3 Alarm Displays and Processing (Continued)
Display Meaning Probable causes Corrective Actions
RUNC Reset during Run Command Input
（闪烁） Error Check that a Run Command is not
外部运 The reset signal was input during Run - being input from an external terminal
行输入 Command input from an external ter- or other source.
不能 minal or other source.
复位
SI-T Watchdog Error Detected
E5 A Watchdog error was detected when
Synchronization error between master Check the communications timing
（闪烁） the Run Command or a frequency ref- controller and Inverter for control
SI-T erence was set from an option board
data. such as communications cycle. *1
WDT and continuous operation was set for
the E5 operation selection.

AEr Check the setting of the station num-

Station number setting error.
（闪烁） SI-T Station Number Setting Error ber. *1
SI-T Station number of SI-T option board
地址 was out of setting range. Check the communications devices
Circuit of SI-T option board is faulty.
故障 and signals. *1

CyC SI-T Communications Cycle Set-

（闪烁） Communications cycle of SI-T option Check the communication cycle of SI-
ting Error
SI-T board set in master controller was out T option board set in master control-
Communications cycle of SI-T option
周期 board was out of range.
of range. ler.*1
故障
Receiving External Baseblock
BB Command
An external baseblock signal was
（闪烁） An external baseblock signal was
input from a multi-function input ter- Check the external sequence.
基极 input from a multi-function input ter-
minal.
封锁 minal, and the Inverter output was
shut down.

The load is too heavy or the accel/ Increase the acceleration/deceleration

decel time is too short. time.

HCA Current Alarm Either a specialized motor or an Verify the setting for the Inverter
（闪烁） The output current has exceeded the excessively large motor is being used. capacity.
电流 overcurrent alarm level (over 150% of
the rated current). Momentary losses in power or fault
警告 The current has risen too high while
restarts may occasionally trigger an
performing speed search either during
overcurrent alarm, and are not neces-
a momentary loss in power or during
sarily indicators of an overcurrent
a fault restart.
problem.

LT-C
（闪烁） Electrolytic Capacitor Maintenance The electrolytic capacitors have Reset constant o2-18 to “0%” after
电容 Timer reached their estimated maintenance
Monitor U1-61 has reached 100%. time period. replacing *2 the electrolytic capacitors.
维护
时期

LT-F
（闪烁） Cooling Fan Maintenance Timer The cooling fan has reached its esti- Replace the cooling fan *2 and set con-
冷却扇 Monitor U1-63 has reached 100%. mated maintenance time period. stant o2-10 to “0H”.
维护
时期
* 1. Refer to MECHATROLINK COMMUNICATIONS INTERFACE CARD INSTRUCTIONS (TOBPC73060008) for details.
* 2. For details on replacement, refer to Chapter 8 Maintenance and Inspection

7-18
 Protective and Diagnostic Functions

‹ Operation Errors
An operation error will occur if there is an invalid setting or a contradiction between two constant settings. It
won't be possible to start the Inverter until the constants have been set correctly. (The alarm output and fault
contact outputs will not operate either.)
When an operation error has occurred, refer to the following table to identify and correct the cause of the
errors.

Table 7.4 Operation Error Displays and Incorrect Settings

Display Meaning Incorrect settings
OPE01 Incorrect Inverter The Inverter capacity setting doesn't match the Unit. (Contact your Yaskawa repre-
参数设定 Capacity Setting sentative.)
故障 1

OPE02 Constant Setting Range The constant setting is outside of the valid setting range. Press the ENTER Key on
参数设定 Error the Digital Operator to display OPE fault constant (U1-34).
故障 2
One of the following errors has been made in the multi-function input (H1-01 to H1-
10) settings:
• The same setting has been selected for two or more multi-function inputs.
• An up or down command was selected independently. (They must be used
together.)
OPE03 • The up/down commands (10 and 11) and Accel/Decel Ramp Hold (A) were
Multi-function Input
参数设定 selected at the same time.
Selection Error
故障 3 • Speed Search 1 (61, maximum output frequency) and Speed Search 2 (62. set fre-
quency) were selected at the same time.
• The up/down commands (10 and 11) were selected while PID Control Method
Selection (b5-01) was enabled.
• Positive and negative speed commands have not been set at the same time.
• The emergency Stop Command NO and NC have been set at the same time.

OPE05 Option Board Selection The option board was selected as the frequency reference source by setting b1-01 to
参数设定 Error 3, but an option board isn't connected (C option).
故障 5

OPE06 Control Method Selec- V/f control with PG feedback was selected by setting A1-02 to 1, but a PG Speed
参数设定 tion Error Control Board isn't connected.
故障 6
The same setting has been selected for the analog input selection and the PID func-
tion selection.
OPE07 Multi-function Analog • H3-09 = B and H6-01 = 1
参数设定 Input Selection Error • H3-09 = C and H6-01 = 2
故障 7 b1-01 (Reference Selection) is set to 4 (pulse input) and H6-01 (Pulse Train Input
Function Selection) is set to a value other than 0 (frequency reference).

OPE08 A setting has been made that is not required in the current control method. Ex.: A
Constant Selection
参数设定 function used only with open-loop vector control was selected for V/f control. Press
Error
故障 8 the ENTER Key on the Digital Operator to display OPE fault constant (U1-34).

The following settings have been made at the same time.

OPE09 PID Control Selection • b5-01 (PID Control Method Selection) has been set to a value other than 0.
参数设定 Error • b5-15 (PID Sleep Function Operation Level) has been set to a value other than 0.
故障 9 • b1-03 (Stopping Method Selection) has been set to 2 or 3.

OPE10 Constants E1-04, E1-06, E1-07, and E1-09 do not satisfy the following conditions:
参数设定 V/f Data Setting Error • E1-04 (FMAX) ≥ E1-06 (FA) > E1-07 (FB) ≥ E1-09 (FMIN)
故障 10 • E3-02 (FMAX) ≥ E3-04 (FA) > E3-05 (FB) ≥ E3-07 (FMIN)

7-19
 Table 7.4 Operation Error Displays and Incorrect Settings (Continued)
Display Meaning Incorrect settings
One of the following constant setting errors exists.
OPE11 • C6-05 (Carrier Frequency Gain) > 6, the Carrier Frequency Lower Limit (C6-04)
参数设定 Constant Setting Error > the Carrier Frequency Gain (C6-05)
故障 11 • Upper/lower limit error in C6-03 to 05.
• C6-02 is 7 to E.

ERR A verification error occurred when writing EEPROM.

EEPROM 读写 EEPROM Write Error • Try turning the power supply off and on again.
故障 • Try setting the constants again.
Note If the settings for the constants of an Inverter with a different version of software are copied, an OPE error can occur. Contact your Yaskawa representative if
wanting to copy the settings with a different software version.

7-20
 Protective and Diagnostic Functions

‹ Errors During Autotuning

The errors that can occur during autotuning are given in the following table. If an error is detected, the motor
will coast to a stop and an error code will be displayed on the Digital Operator. The error contact output and
alarm output will not function.
Table 7.5 Errors During Autotuning
Display Meaning Probable causes Corrective Actions
There is an error in the data input for
autotuning.
There is an error in the relationship
• Check the input data.
between the motor output and the motor
• Check the capacity of the Inverter and
rated current.
电机数据故障 Motor data error motor.
The is an error between the no-load cur-
• Check the motor rated current and no-
rent setting and the input motor rated
load current.
current (when autotuning for only line-
to-line resistance is performed for vector
control).
A minor fault occurred during
轻故障 Alarm • Check the input data.
autotuning (xxx).
• Check wiring and the machine.
The STOP Key was pressed to cancel • Check the load.
输入了 STOP 键 STOP key input
autotuning.
Line-to-line resis-
线间电阻故障 tance error Autotuning was not completed in the • Check the input data.
specified time. • Check motor wiring.
空载电流故障 No-load current error The results of autotuning has exceeded • If the motor is connected to the
the setting range for a user constant. machine, disconnect it.
额定滑差故障 Rated slip error
• Increase C1-01 (Acceleration Time 1).
Acceleration error • Increase L7-01 and L7-02 (Reverse
The motor did not accelerate in the spec-
加速故障 (detected only for Torque Limits) if they are low.
ified time.
rotational autotuning) • If the motor is connected to the
machine, disconnect it.
• Check the PG wiring.
There is a faulty connection between the
电机方向 Motor Direction • Check the motor wiring.
Inverter and PC (A or B phase) or the
故障 Error • Check the PG rotation direction and
Inverter and Motor (U, V, or W).
F1-05 (PG rotation).
• If the motor is connected to the
Motor speed error machine, disconnect it.
The torque reference was too high
(detected only for • Increase C1-01 (Acceleration Time 1).
电机速度故障 (100%) during acceleration (for open-
rotational autotuning) • Check the input data (particularly the
loop vector control only).
number of PG pulses and the number
of motor poles).
The current flow exceeded the motor
rated current.
Check the current detection circuit,
Current detection The detected current sign was the oppo-
电流检出故障 motor wiring, current detector, and
error site of what it should be. installation methods.
There is a phase fault for U, V, or W.
Leakage inductance Autotuning was not completed in the
漏电故障 Check motor wiring.
error specified time.
PG Disconnection PG pulses were input when the Inverter
PG 断线检出 Fix the broken/disconnected wiring.
Detected was outputting a frequency.
The torque reference exceeded 100%
V/f settings exces- • Check and correct the settings.
V/F 设定过大 and the no-load torque exceeded 70%
sive* • Disconnect the load from the motor.
during autotuning.

7-21
 Table 7.5 Errors During Autotuning (Continued)
Display Meaning Probable causes Corrective Actions
Motor core satura- The results of autotuning has exceeded • Check the input data.
tion error (detected the setting range for a user constant so a • Check motor wiring.
饱和系数故障 only for rotational temporary setting was made for the • If the motor is connected to the
autotuning)* motor core saturation coefficient. machine, disconnect it.

Rated current setting Check the input data (particularly the

额定电流警告 The rated current is set high. motor output current and motor rated
alarm* current).
Check the input data.
As a result of stationary autotuning 1,
Adjusted slip value
滑差调整下限值 the slip value has fallen to 0.2 Hz or If rotational autotuning is possible, per-
fell below lower limit
below. form it. If impossible, perform stationary
autotuning 2.
* Displayed after autotuning has been completed. For constants in which no error is detected, the settings are reset to the values determined by autotuning.

‹ Errors when Using the Digital Operator Copy Function

The errors that can occur when using the copy function from the Digital Operator are given in the following
table. An error code will be displayed on the Digital Operator. If a Digital Operator key is pressed when an
error code is being displayed, the display will be cleared and 03-01 will be displayed. The error contact output
and alarm output will not function.

Table 7.6 Errors during Copy Function

Func-
Display Meaning Probable causes Corrective Actions
tion
PRE o3-01 was set to 1 to write a constant
Digital Operator Set o3-02 to 1 to enable writing con-
READ when the Digital Operator was write-
write-protected stants with the Digital Operator.
IMPOSSIBLE protected (o3-02 = 0).

IFE The read data length does not agree. Repeat the read.
READ READ DATA Illegal read data Check the Digital Operator cable.
功能 ERROR The write data is incorrect. Replace the Digital Operator.

A low Inverter voltage has been

RDE An attempted write of a constant to detected.
Illegal write status
DATA ERROR EEPROM on the Digital Writer failed. Repeat the read.
Replace the Digital Operator.

7-22
 Protective and Diagnostic Functions

Table 7.6 Errors during Copy Function (Continued)

Func-
Display Meaning Probable causes Corrective Actions
tion
CPE The Inverter product code or software Use the copy function for the same
ID not matched
ID UNMATCH number is different. product code and software number.

VAE The capacity of the Inverter being

Inverter capacity Use the copy function for the same
INV. KVA copied and the capacity in the Digital
matched Inverter capacity.
UNMATCH Operator are different.

CRE The control method of the Inverter

Control method Use the copy function for the same
CONTROL being copied and the control method
matched control method.
UNMATCH in the Digital Operator are different.
COPY The constant written to the Inverter
功能 CYE was compared with the constant in the
Verify error Retry the copy.
COPY ERROR Digital Operator and they were differ-
ent.

The checksum in the Inverter constant

area was compared with the checksum
CSE Retry the copy.
in the Digital Operator constant area
SUM CHECK Checksum error and they were different.
ERROR
The Inverter product code or software Use the copy function for the same
number is different. product code and software number.

VYE
The Digital Operator and Inverter set-
VERIFY Verify error Retry the copy and verify again.
tings do not agree.
VERIFY ERROR
功能
CPE The Inverter product code or software Use the copy function for the same
ID not matched
ID UNMATCH number is different. product code and software number.

7-23
 Troubleshooting
Due to constant setting errors, faulty wiring, and so on, the Inverter and motor may not operate as
expected when the system is started up. If that should occur, use this section as a reference and apply the
appropriate measures.

If the contents of the fault are displayed, refer to Protective and Diagnostic Functions.

‹ If Constant Constants Cannot Be Set

Use the following information if an Inverter constant cannot be set.

„The display does not change when the Increment and Decrement Keys are pressed.
The following causes are possible.

The Inverter is operating (drive mode).

There are some constants that cannot be set during operation. Turn the Inverter off and then make the settings.

Constant write enable is input.

This occurs when “constant write enable” (set value: 1B) is set for a multi-function input terminal (H1-01 to
H1-10). If the constant write enable input is OFF, the constants cannot be changed. Turn it ON and then set the
constants.

Passwords do not match. (Only when a password is set.)

If the constant A1-04 (Password) and A1-05 (Password Setting) numbers are different, the constants for the
initialize mode cannot be changed. Reset the password.
If you cannot remember the password, display A1-05 (Password Setting) by pressing the Reset/Select Key and
the Menu Key simultaneously while in the A1-04 display. Then reset the password. (Input the reset password
in constant A1-04.)

„OPE01 through OPE11 is displayed.

The set value for the constant is wrong. Refer to Operation Errors in this chapter and correct the setting.

„CPF00 or CPF01 is displayed.

This is a Digital Operator communications error. The connection between the Digital Operator and the
Inverter may be faulty. Remove the Digital Operator and then re-install it.

7-24
 Troubleshooting

‹ If the Motor Does Not Operate

Use the following information if the motor does not operate.

„The motor does not operate when the RUN Key on the Digital Operator is pressed.
The following causes are possible.

If the Inverter is not in drive mode and the DRIVE indicator on the Digital Operator (JVOP-161) does not light
up, the Inverter will remain in ready status and will not start. Press the Menu Key to display the drive mode,
and enter the drive mode by pressing the DATA/ENTER Key. “-Rdy-” will be displayed when drive mode is
IMPORTANT entered.

The operation method setting is wrong.

If constant b1-02 (Operation Method Selection) is set to 1 (control circuit terminal), the motor will not operate
when the Run Key is pressed. Either press the LOCAL/REMOTE Key* to switch to Digital Operator opera-
tion or set b1-02 to 0 (Digital Operator).

The LOCAL/REMOTE Key is enabled by setting o2-01 to 1 and disabled by setting o2-01 to 2. It is enabled
when the drive mode is entered.

INFO

The frequency reference is too low.

If the frequency reference is set below the frequency set in E1-09 (Minimum Output Frequency), the Inverter
will not operate.
Raise the frequency reference to at least the minimum output frequency.

There is a multi-function analog input setting error.

If multi-function analog input H3-09 is set to 1 (frequency gain), and if no voltage (current) is input, then the
frequency reference will be zero. Check to be sure that the set value and analog input value are correct.

„The motor does not operate when an external operation signal is input.
The following causes are possible.

The Inverter is not in drive mode.

If the Inverter is not in drive mode and the DRIVE indicator on the Digital Operator (JVOP-161) does not
light up, the Inverter will remain in ready status and will not start. Press the MENU Key to make the DRIVE
indicator flash, and enter the drive mode by pressing the DATA/ENTER Key. “-Rdy-” will be displayed when
drive mode is entered.

7-25
 The operation method selection is wrong.
If constant b1-02 (reference selection) is set to 0 (Digital Operator), the motor will not operate when an exter-
nal operation signal is input. Set b1-02 to 1 (control circuit terminal) and try again.
Similarly, the motor will also not operate if the LOCAL/REMOTE Key has been pressed to switch to Digital
Operator operation. In that case press the LOCAL/REMOTE Key* again to return to the original setting.

The LOCAL/REMOTE Key is enabled by setting o2-01 to 1 and disabled by setting o2-01 to 2. It is enabled
when the drive mode is entered.

INFO

A 3-wire sequence is in effect.

The input method for a 3-wire sequence is different than when operating by forward/stop and reverse/stop (2-
wire sequence). When 3-wire sequence is set, the motor will not operate even when an input terminal suitable
for forward run/stop and reverse run/stop is turned ON.
When using a 3-wire sequence, refer to the timing chart and input the proper signals.
When using a 2-wire sequence, set the multi-function input terminal (H1-01 through H1-10, terminals S3 to
S11) to a value other than 0.

The frequency reference is too low.

If the frequency reference is set below the frequency set in E1-09 (Minimum Output Frequency), the Inverter
will not operate. Raise the frequency reference to at least the minimum output frequency.

There is a multi-function analog input setting error.

If multi-function analog inputs H3-05 (Multi-function Analog Input Terminal A3 Selection) and H3-09
(Multi-function Analog Input Terminal A2 Selection) are set to 1 (frequency gain), and if no voltage (current)
is input, then the frequency reference will be zero. Check to be sure that the set value and analog input value
are correct.

„The Inverter does not operate.

When the motor does not operate, and there is no fault or alarm indication, check the items listed below to find
the cause and take corrective action.
Table 7.7 Troubleshooting when Motor Does Not Operate
Probable Causes Descriptions Corrective Actions
If the indicator on the RUN Key is not lit,
Inverter does not operate if a Run command
Run command is not sent. the Run Command is not sent. Input the
is not sent.
Run Command.
b1-02 has to be set according to the Run
Command input method to be used.
b1-02=
The operation method 0: Digital Operator Set b1-02 according to the Run Command
selection is wrong. 1: Control circuit terminal (factory setting) input method to be used.
2: MEMOBUS communications
3: Option board
4: Pulse train input
If the indicator on the STOP Key is flash-
The frequency reference has to be set above ing, check the frequency reference moni-
The frequency reference is
the frequency set in E1-09 (Minimum Out- tor (U1-01) and set the frequency
too low.
put Frequency). reference above the frequency set in E1-
09.

7-26
 Troubleshooting

Table 7.7 Troubleshooting when Motor Does Not Operate (Continued)

Probable Causes Descriptions Corrective Actions
b1-01 has to be set according to the fre-
quency reference input method to be used.
b1-01=
The frequency reference 0: Digital Operator Set b1-01 according to the frequency ref-
selection is wrong. 1: Control circuit terminal (factory setting) erence input method to be used.
2: MEMOBUS communications
3: Option board
4: Pulse train input
The MENU Key was • Press the DATA/ENTER Key.
pressed. If the MENU Key is pressed once or the • Try turning the power supply off and on
ESC Key is pressed twice, the Inverter will again.
exit the drive mode and will not operate. If • Set b8-01 (Run Command selection in
The ESC Key was pressed the MENU Key is pressed during operation, programming modes) to 1(Cannot oper-
twice. the Inverter will not start even if the Run ate) to remain in the drive mode and
Command is sent at the next operation. continue operation even if the MENU
Key or ESC Key is pressed.
• Press the LOCAL/REMOTE Key.
If the LOCAL/REMOTE Key is pressed
• Try turning the power supply off and on
while the Inverter is stopped, the Inverter
The LOCAL/REMOTE Key again.
will switch to Digital Operator operation
was pressed. • Set o2-01 (LOCAL/REMOTE Key
and cannot be operated with the external
enable/disable) to 0 (Disabled) to dis-
input terminals.
able the LOCAL/REMOTE Key.
• Turn the Run Command off and then on
again.
The STOP Key was If the STOP Key is pressed during opera-
• Set o2-02 (STOP key during control cir-
pressed. tion, the Inverter will decelerate to a stop.
cuit terminal operation) to 0 (Disabled)
to disable the STOP Key.
Make sure that H1-01 to H1-10 are set to a
Wrong selection of a 2-wire If 0 is set to one of H1-01 to H1-10, a 3-
value other than 0 to use a 2-wire
or a 3-wire sequence. wire sequence is set.
sequence.
If b1-04 (Prohibition of reverse operation)
“Reverse run prohibited” is is set to 1 (Reverse disabled), the motor will
Check the setting of b1-04.
selected. not start if the Reverse Run Command is
sent.
The Inverter remains in the autotuning Press the MENU Key to display the drive
Autotuning has just been mode right after autotuning has been com- mode on the Digital Operator and press
completed. pleted and cannot be operated even if the the DATA/ENTER Key to enter the drive
Run Command is sent. mode.

„The motor stops during acceleration or when a load is connected.

The load may be too heavy. The Inverter has a stall prevention function and an automatic torque boost func-
tion, but the motor responsiveness limit may be exceeded if acceleration is too rapid or if the load is too heavy.
Lengthen the acceleration time or reduce the load. Also consider increasing the motor capacity.

„The motor does not accelerate.

If the torque limit settings (L7-01 to L7-04) or the torque reference input (torque control) are too small, the
motor may not be able to accelerate. Check the settings and input values. Also, for operation with open-loop
vector 2 control, refer to Corrective Actions for Control Faults (CF) on page 7-14.

7-27
 „The motor only rotates in one direction.
“Reverse run prohibited” is selected. If b1-04 (Prohibition of Reverse Operation) is set to 1 (reverse run pro-
hibited), the Inverter will not receive Reverse Run Commands. To use both forward and reverse operation, set
b1-04 to 0.

‹ If the Direction of the Motor Rotation is Reversed

If the motor operates in the wrong direction, the motor output wiring is faulty. When the Inverter T1 (U), T2
(V), and T3 (W) are properly connected to the motor T1 (U), T2 (V), and T3 (W), the motor operates in a for-
ward direction when a Forward Run Command is executed. The forward direction depends on the manufac-
turer and the motor type, so be sure to check the specifications.
The direction of rotation can be reversed by switching two wires among T1 (U), T2 (V), and T3 (W).

‹ If the Motor Does Not Put Out Torque or If Acceleration is Slow

Use the following information if the motor does not output torque or if acceleration is too slow.

„The torque limit has been reached.

When a torque limit has been set in constants L7-01 to L7-04, no torque will be output beyond that limit. This
can cause the torque to be insufficient, or the acceleration time to be too long. Check to be sure that the value
set for the torque limit is suitable.
If torque limits have been set for the multi-function analog input (H3-05 or H3-09 = 10 to 12 or 15), check to
be sure that the analog input value is suitable.

„The stall prevention level during acceleration is too low.

If the value set for L3-02 (Stall Prevention Level during Acceleration) is too low, the acceleration time will be
too long. Check to be sure that the set value is suitable.

„The stall prevention level during running is too low.

If the value set for L3-06 (Stall Prevention Level during Running) is too low, the speed will drop before out-
putting torque. Check to be sure that the set value is suitable.

„Autotuning has not been performed for vector control

Vector control will not perform if autotuning has not been performed. Perform autotuning separately for the
motor, or set the motor constants through calculations. Alternatively, change the Control Method Selection
(A1-02) to V/f control (0 or 1).

‹ If the Motor Operates Higher Than the Reference

Use the following information if the motor operates higher than the reference.

7-28
 Troubleshooting

„The analog frequency reference bias setting is wrong (the gain setting is wrong).
The frequency reference bias set in constant H3-03 is added to the frequency reference. Check to be sure that
the set value is suitable.

„A signal is being input to the frequency reference (current) terminal A2 or A3.

When 0 (Add to terminal A1) is set for constant H3-09 (Multi-function Analog Input Terminal A2 Function
Selection) or H3-05 (Multi-function Analog Input Terminal A3 Function Selection), a frequency correspond-
ing to the terminal A2 or A3 input voltage (current) is added to the frequency reference. Check to be sure that
the set value and analog input value are suitable.

‹ If the Slip Compensation Function Has Low Speed Precision

If speed control accuracy is low for the slip compensation function, the slip compensation limit has been
reached. With the slip compensation function, compensation cannot be carried out beyond the slip compensa-
tion limit set in constant C3-03. Check to be sure that the set value is suitable.

‹ If There is Low Speed Control Accuracy at High-speed Rotation in Open-

loop Vector Control Method
The motor's rated voltage is high.
The Inverter's maximum output voltage is determined by its input voltage. (For example, if 200 VAC is input,
then the maximum output voltage will be 200 VAC.) If, as a result of vector control, the output voltage refer-
ence value exceeds the Inverter output voltage maximum value, the speed control accuracy will decrease. Use
a motor with a low rated voltage (i.e., a special motor for use with vector control), or change to flux vector
control.

‹ If Motor Deceleration is Slow

Use the following information when the motor deceleration is slow.

„The deceleration time is long even when braking resistor is connected.

The following causes are possible.

“Stall prevention during deceleration enabled” is set.

When braking resistor is connected, set constant L3-04 (Stall Prevention Selection during Deceleration) to 0
(disabled) or 3 (with braking resistor). When this constant is set to 1 (enabled, the factory setting), braking
resistor does not fully function.

The deceleration time setting is too long.

Check the deceleration time setting (constants C1-02, C1-04, C1-06, and C1-08).

Motor torque is insufficient.

If the constants are correct and there is no overvoltage fault, then the motor's power is limited. Consider
increasing the motor capacity.

7-29
 The torque limit has been reached.
When a torque limit has been set in constants L7-01 to L7-04, no torque will be output beyond that limit. This
can cause the deceleration time to be too long. Check to be sure that the value set for the torque limit is suit-
able.
If H3-09 (Multi-function Analog Input Terminal A2 Function Selection) or H3-05 (Multi-function Analog
Input Terminal A3 Function Selection) is set to 10, 11, 12 or 15 (positive and negative torque limit), check to
be sure that the analog input value is suitable.

„If the Vertical-axis Load Drops When Brake is Applied

The sequence is incorrect. The Inverter goes into DC injection braking status for 0.5 seconds after deceleration
is completed. (This is the factory-set default.)
To ensure that the brake holds, set frequency detection 2 (H2-01 = 5) for the multi-function contact output ter-
minals (M1 and Mw) so that the contacts will turn OFF when the output frequency is greater than L4-01 (3.0
to 5.0 Hz). (The contacts will turn ON below L4-01.)
There is hysteresis in frequency detection 2 (i.e., a frequency detection width, L4-02 = 2.0 Hz). Change the
setting to approximately 0.5 Hz if there are drops during stop. Do not use the multi-function contact output run
signal (H2-01 = 0) for the brake ON/OFF signal.

‹ If the Motor Overheats

Take the following steps if the motor overheats.

„The load is too big.

If the motor load is too heavy and the motor is used with the effective torque exceeding the motor's rated
torque, the motor will overheat. Some motor rating are given for short period performance and are not contin-
uous ratings. Reduce the load amount by either lightening the load or lengthening the acceleration/decelera-
tion time. Also consider increasing the motor capacity.

„The ambient temperature is too high.

The motor rating is determined within a particular ambient operating temperature range. The motor will burn
out if it is run continuously at the rated torque in an environment in which the maximum ambient operating
temperature is exceeded. Lower the motor's ambient temperature to within the acceptable ambient operating
temperature range.

„The withstand voltage between the motor phases is insufficient.

When the motor is connected to the Inverter output, a surge is generated between the Inverter switching and
the motor coil. Normally the maximum surge voltage is three times the Inverter's input power supply voltage
(i.e., 1,200 V for 400 V Class). Be sure to use a motor with a withstand voltage between the motor phases that
is greater than the maximum surge voltage. In particular, when using a 400 V Class Inverter, use a special
motor for Inverters.

„Autotuning has not been performed for vector control

Vector control will not perform if autotuning has not been performed. Perform autotuning, or set the motor
constants through calculations. Alternatively, change the Control Method Selection (A1-02) to V/f control (0
or 1).

7-30
 Troubleshooting

‹ If There is Noise When the Inverter is Started or From an AM Radio

If noise is generated by Inverter switching, implement the following countermeasures:
• Change the Inverter's Carrier Frequency Selection (C6-02) to lower the carrier frequency. This will help to
some extent by reducing the amount of internal switching.
• Install an Input Noise Filter at the Inverter's power supply input area.
• Install an Output Noise Filter at the Inverter's power supply output area.
• Use metal tubing. Electric waves can be shielded by metal, so encase the Inverter with metal (steel).
• Ground the Inverter and motor.
• Separate main circuit wiring from control wiring.

‹ If the Ground Fault Interrupter Operates When the Inverter is Run

The Inverter performs internal switching, so there is a certain amount of leakage current. This may cause the
ground fault interrupter to operate and cut off the power supply. Change to a ground fault interrupter with a
high leakage detection level (i.e., a sensitivity current of 200 mA or greater per Unit, with an operating time of
0.1 s or more), or one that incorporates high frequency countermeasures (i.e., one designed for use with Invert-
ers). It will also help to some extent to change the Inverter's Carrier Frequency Selection (C6-02) to lower the
carrier frequency. In addition, remember that the leakage current increases as the cable is lengthened.

‹ If There is Mechanical Oscillation

Use the following information when there is mechanical oscillation.

„The machinery is making unusual sounds.

The following causes are possible.

There may be resonance between the mechanical system's characteristic frequency and the
carrier frequency.
If the motor is running with no problems and the machinery is oscillating with a high-pitched whine, it may
indicate that this is occurring. To prevent this type of resonance, adjust the carrier frequency with constants
C6-02 to C6-05.

There may be resonance between a machine's characteristic frequency and the output fre-
quency of the Inverter.
To prevent this from occurring, either use the jump frequency functions in constants d3-01 to d3-04 or install
rubber padding on the motor base to reduce oscillation.

„Oscillation and hunting are occurring with open-loop vector 1 control.

The gain adjustment may be insufficient. Reset the gain to a more effective level by adjusting constants C4-02
(torque compensation time constant), C2-01 (S-curve Characteristic Time at Acceleration Start), and C3-02
(Slip Compensation Primary Delay Time) in order. Lower the gain setting and raise the primary delay time
setting.

7-31
 Vector control will not perform if autotuning has not been performed. Perform autotuning separately for the
motor, or set the motor constants through calculations. Alternatively, change the control method selection (A1-
02) to V/f control (0 or 1).

„Oscillation and hunting are occurring with V/f control.

The gain adjustment may be insufficient. Reset the gain to a more effective level by adjusting constants C4-02
(Torque Compensation Primary Delay Time Constant), N1-02 (Hunting Prevention Gain), and C3-02 (Slip
Compensation Primary Delay Time) in order. Lower the gain setting and raise the primary delay time setting.

„Oscillation and hunting are occurring with V/f w/PG control.

The gain adjustment may be insufficient. Adjust the various types of speed control loop (ASR) gain.
If the oscillation cannot be eliminated in this way, set the hunting prevention selection (constant N1-01) to 0
(disabled) and then try adjusting the gain again.

„Oscillation and hunting are occurring with open-loop vector 2 control.

Adjust the control constants with reference to Adjusted User Constants on page 18 in Chapter 4 Trial Opera-
tion. If autotuning has not been performed, or the control method has been changed since last performing auto-
tuning, perform autotuning. If the problem occurs after performing stationary autotuning, perform rotational
autotuning.
If oscillation and hunting occur under the following special conditions, perform the adjustments described
here.

Low-speed regenerative load

• If oscillation occurs during low-speed regeneration, increase the setting of N4-30 (low-speed regeneration
stability coefficient 2). Increase the setting in intervals of approximately 0.2. The larger the setting, the
greater the ratio of the speed increase relative to the regenerative load will be.

Operating frequency between 6 and 10 Hz

• Accelerate the motor gradually, set N4-32 (speed estimator gain fluctuation frequency 1) to the lowest
speed at which oscillation occurs and set N4-33 (speed estimator gain fluctuation frequency 2) to the high-
est. Then, reduce the setting of N4-34 (speed estimator gain fluctuation rate) until the oscillation stops.
Adjust N4-34 in intervals of approximately 5% in the range 50% to 100%.

„Oscillation and hunting are occurring with flux vector control.

The gain adjustment is insufficient. Adjust the various gains for speed control (ASR). If the oscillation points
overlap with those of the machine and cannot be eliminated, increase the primary delay time constant for
speed control (ASR) in C5-06 and then readjust the gains.
If autotuning is not performed, proper performance cannot be achieved for vector control. Perform autotuning
or set the motor constants according to calculations.

„Oscillation and hunting are occurring with PID control.

If there is oscillation or hunting during PID control, check the oscillation cycle and individually adjust P, I,
and D constants. (Refer to page 6-110.)

7-32
 Troubleshooting

„Autotuning has not been performed with vector control.

Vector control will not perform if autotuning has not been performed. Perform autotuning separately for the
motor, or set the motor constants through calculations. Alternatively, change the Control Method Selection
(A1-02) to V/f control.

‹ If the Torque Generated for the Motor is Insufficient (Insufficient Power)

If autotuning has not been performed, or the control method has been changed since last performing
autotuning, perform autotuning. If the problem occurs after performing stationary autotuning, perform rota-
tional autotuning.

„The torque is insufficient with open-loop vector 2 control (insufficient power).

In particular, if there is insufficient power at low speeds, make adjustments using the following methods.

Low-speed Electromotive Load

Increase the setting of N4-29 (torque adjustment gain 2). Increase the setting in intervals of approximately
0.05. If the setting is too high, it may have the opposite effect and so do not change the setting by a large
amount.

Low-speed Regenerative Load

Increase the setting of N4-15 (low-speed regeneration stability coefficient 1). Increase the setting in intervals
of approximately 0.1. If the setting is too large, the torque reference monitor and the actual torque accuracy
may deteriorate and so do not change the setting by a large amount.

‹ If the Torque Reference (U1-09) at Low Speeds in Open-loop Vector 2

Control is Large Compared to That at Medium and High Speeds
If the torque reference (U1-09) at low speeds is large compared to that at medium and high speeds for the
same load conditions, make adjustments in the way described below.
• Reduce the setting for N4-17 (torque adjustment gain).
• If the problem still occurs after making the above adjustment, linearize the V/f characteristics. This means
making the ratios E1-10/E1-09 and E1-08/E1-07 closer to the ratio E1-13/E1-06. Linearizing the V/f char-
acteristics will, however, reduce the power and so check that the power is sufficient after changing the set-
tings. Do not change the settings more than necessary.

‹ If Shock Occurs Near the Speed Estimator Switching Frequency in Open-

loop Vector 2 Control
The switching frequency refers to the frequency range near the N4-11 setting during acceleration and near the
N4-28 setting during deceleration. In open-loop vector 2 control, two speed estimators are switched between
and there may be instances of shock occurring at the switchover. If switching shock is a problem, make the
adjustments described below.
• If shock occurs during acceleration:
• Increase the acceleration time within the allowable range. Alternatively, reduce the torque limit.

7-33
 • Reduce the setting for N4-11 to a value less than the factory setting. Reduce the setting in intervals of
approximately 5 Hz.
• If shock occurs during deceleration:
• Increase the deceleration time within the allowable range. Alternatively, reduce the torque limit.
• Reduce the setting for N4-28 to a value less than the factory setting. Reduce the setting in intervals of
approximately 5 Hz.
The factory settings for N4-11 (speed estimator switching frequency) and N4-28 (speed estimator switching
frequency 2) are 70 Hz and 50 Hz respectively. If the problem still occurs after making the above adjustments,
use open-loop vector 1 control (A1-02 = 2).

‹ If Torque Ripple Occurs at Very Low Speeds in Open-loop Vector 2 Con-

trol
Either increase the operating frequency or use open-loop vector 1 control (A1-02 = 2).

‹ If the Motor Rotates Even When Inverter Output is Stopped

If the motor rotates even when the Inverter output is stopped, the DC injection braking is insufficient. If the
motor continues operating at low speed, without completely stopping, and after a deceleration stop has been
executed, it means that the DC injection braking is not decelerating enough. Adjust the DC injection braking
as follows:
• Increase the constant b2-02 (DC Injection Braking Current) setting.
• Increase the constant b2-04 (DC Injection Braking (initial excitation) Time at Stop) setting.

‹ If OV is Detected When the Fan is Started, or Fan Stalls

Generation of OV (main circuit voltage) and stalling can occur if the fan is turning when it is started. The DC
injection braking is insufficient when starting.
This can be prevented by slowing fan rotation by DC injection braking before starting the fan. Increase the
constant b2-03 (DC injection braking time (initial excitation) at start) setting.

‹ If Output Frequency Does Not Rise to Frequency Reference

Use the following information if the output frequency does not rise to the frequency reference.

„The frequency reference is within the jump frequency range.

When the jump frequency function is used, the output frequency does not change within the jump frequency
range. Check to be sure that the Jump Frequency (constants d3-01 to d3-03) and Jump Frequency Width (con-
stant d3-04) settings are suitable.

7-34
 Troubleshooting

„The frequency reference upper limit has been reached.

The output frequency upper limit is determined by the following formula:
Maximum Output Frequency (E1-04) × Frequency Reference Upper Limit (d2-01) / 100
Check to be sure that the constant E1-04 and d2-01 settings are suitable.

‹ Acoustic Noise From the Motor

The carrier frequency is automatically reduced if a current exceeding 110% of the Inverter rated current flows
while the Inverter output frequency is low. When the carrier frequency is reduced, acoustic noise form the
motor will change.
If acoustic noise from the motor causes a problem, change L8-38 (Carrier frequency reduction selection) to 0
(Disabled). However, for mechanical loads that require repetitive high torque, such as with cranes, leave L8-
38 to 1 (Enabled) without changing.
Acoustic noise from the motor can be changed by changing the setting of L8-39 (Reduced carrier frequency).
(The minimum set value is 1.0 kHz for open-loop vector control.)

7-35
 Maintenance and
Inspection
This chapter describes basic maintenance and inspection for the Inverter.

Maintenance and Inspection........................................8-2

 Maintenance and Inspection

‹ Outline of Warranty
The warranty period of the Inverter is as follows:
Warranty Period: This product is warranted for twelve months after being delivered to Yaskawa's customer or
if applicable eighteen months from the date of shipment from Yaskawa's factory whichever comes first.

‹ Daily Inspection
Check the following items with the system in operation.
• The motor should not be vibrating or making unusual noises.
• There should be no abnormal heat generation.
• The ambient temperature should not be too high.
• The output current value shown on the monitor displays should not be higher than normal.
• The cooling fan on the bottom of the Inverter should be operating normally.

‹ Periodic Inspection
Check the following items during periodic maintenance.
Always turn OFF the power supply before beginning inspection. Confirm that the LCD and LED indicators on
the front cover have all turned OFF, and then wait until at least five minutes has elapsed before beginning the
inspection. Be sure not to touch terminals right after the power has been turned off. Doing so can result in
electric shock.

Table 8.1 Periodic Inspections

Item Inspection Corrective Procedure
External terminals, Are all screws and bolts tight? Tighten loose screws and bolts firmly.
mounting bolts, connec-
tors, etc. Are connectors tight? Reconnect the loose connectors.

Clean off any dirt and dust with an air gun using
Heatsinks Are the fins dirty or dusty? dry air at a pressure of 39.2 x 104 to 58.8 x 104 Pa
(4 to 6 kg•cm2).
Clean off any dirt and dust with an air gun using
Is there any conductive dirt or oil mist on dry air at a pressure of 39.2 x 104 to 58.8 x 104 Pa
PCBs
the PCBs? (4 to 6 kg•cm2).
Replace the boards if they cannot be made clean.
Is there any abnormal noise or vibration or
Cooling fan has the total operating time exceeded Replace the cooling fan.
20,000 hours?
Clean off any dirt and dust with an air gun using
Is there any conductive dirt or oil mist on
Power elements dry air at a pressure of 39.2 x 104 to 58.8 x 104 Pa
the elements?
(4 to 6 kg•cm2).
Are there any irregularities, such as dis-
Smoothing capacitor Replace the capacitor or Inverter.
coloration or odor?

8-2
 Maintenance and Inspection

‹ Periodic Maintenance of Parts

The Inverter is configured of many parts, and these parts must be operating properly in order to make full use
of the Inverter functions.
Among the electronic components, there are some that require maintenance depending on their usage condi-
tions. In order to keep the Inverter operating normally over a long period of time, it is necessary to perform
period inspections and replace parts according to their service life.
Periodic inspection standards vary depending the Inverter's installation environment and usage conditions.
The Inverter's maintenance periods are noted below. Keep them as reference.
Refer to Cooling Fan Replacement Outline (Page 8-6) for replacing a cooling fan and Circulation Fan
Replacement Outline (Page 8-16) for replacing a circulation fan.
To replace other parts, contact your Yaskawa representative or YASKAWA ELECTRIC ENGINEERING
CORPORATION for details on preventive maintenance for Inverters.

Table 8.2 Part Replacement Guidelines

Part Standard Replacement Period Replacement Method
Cooling fan 2 to 3 years Replace with new part.
Replace with new part. (Determine need by
Smoothing capacitor 5 years
inspection.)
Breaker relays - Determine need by inspection.
Fuses 10 years Replace with new part.
Replace with new board. (Determine need by
Aluminum capacitors on PCBs 5 years
inspection.)
Note The standard replacement period is based on the following usage conditions:
Ambient temperature:Yearly average of 30°C
Load factor: 80% max.
Operating rate: 12 hours max. per day

‹ Procedure for Adjusting Constants after Replacement of Control Board

Perform the following operations before adjusting the constants.
• For 400-V class Inverters of 55 kW to 300 kW, take safety measures such as the installation of an emer-
gency-stop switch. Failure to do so may result in injury caused by the motor accidentally rotating during
stationary autotuning performed by the Inverter when the constants are adjusted.
• Before replacing the control board, first use the COPY function of the Digital Operator to copy the settings
of the constants of board from the Inverter to the Digital Operator.
When using the copy function of the Digital Operator, check that the following settings are the same between
the Inverter and the Digital Operator. Note the setting of A1-02 (Control method selection).
• Inverter product and type
• Software number
• Inverter capacity and voltage
• Control method
Refer to Copying Constants in Chapter 6.
After replacing the board, use the following procedure to adjust the constants.
Steps 4 and 5 are not required for 400-V class Inverters of 0.4 kW to 45 kW, and all models of 200-V class
Inverters regardless of capacity. If using a 400-V class Inverter of 55 kW to 300 kW then perform steps 4 and
5.
Contact your Yaskawa representative if a motor cannot be connected, the motor being used is two frames
smaller than the Inverter.

8-3
 Step No. Digital Operator Display Description

1 Set o2-04 (kVA selection) to the capacity of the Inverter that you use.

Set A1-02 to the control method to be used. The value of the control method
2 should be set to the same value as when the constants were copied from the
Inverter to the Digital Operator.

Set A1-03 (Initialize) to 2220 (2-wire initialization) or 3330 (3-wire initializa-

3 tion).
This example is a typical setting for initialization by a 2-wire sequence.

If the mode is switched to the DRIVE after initialization has been completed,
the motor power setting display appears. Set T1-02 (Motor output power) to
4
the motor capacity of the connected motor.
This example is the setting for a 55 kW motor.
Press the Increment Key to view the shipping adjustment display. After con-
firming that the motor has been connected, press the RUN Key to start auto-
5 tuning.
Note: Do not touch the motor terminals. Although the motor does not rotate,
voltage is being supplied to the motor though the motor is not rotating.
After autotuning has been completed, use the copy function of the Operator to
copy the settings of the constants of the control board from the Operator to the
6 - Inverter before replacing the board.
If the copy function is not available, change the setting of the constants manu-
ally.

If the mode is switched to the DRIVE, the frequency setting display appears,
7
and the operation becomes enabled.

„Procedure for Changing Constants through Communications

For 400-V class Inverters of 55 kW to 300 kW, take safety measures such as the installation of an emergency-
stop switch before adjusting constants. Failure to do so may result in injury caused by the motor accidentally
rotating during stationary autotuning performed by the Inverter when the constants are adjusted.
After replacing the control board, write in all of the constants to the new board with MEMOBUS communica-
tions or a Communications Option Board.
Next, be sure to perform autotuning to make adjustments after shipping.
Step No. Digital Operator Display Description

1 Set T1-01 (Autotuning mode selection) to 3 (Shipping adjustment).

Press the Increment Key to view the motor rated power display. Set T1-02
2
(Motor output power) to the capacity of the connected motor.

Press the Increment Key to view the motor rated current display. Set T1-04
3
(Motor rated current) to the value of motor rated current.

Press the Increment Key to view the shipping adjustment display.

After confirming that the motor has been connected, press the RUN Key to
4 start autotuning.
Note: Do not touch the motor terminals. Although the motor does not rotate,
voltage is being supplied to the motor though the motor is not rotating.

8-4
 Maintenance and Inspection

‹ Types and Number of Cooling Fans Used in the Drive

Cooling fans used for the Drive has two types; Heatsink cooling fan and heatsink circulation fan. Heatsink
cooling fan blows air to the Drive cooling fin. Heatsink circulation fan stirs up the air inside the Drive unit.
Table 8.3 shows the number of cooling fans used in the Drive. For more information on models and specifica-
tions of cooling fans, contact your Yaskawa representative or YASKAWA ELECTRIC ENGINEERING COR-
PORATION.
When replacing the fan, use the specified type of the fan. If the inapplicable fans are used, performance of the
Drive will not be fully obtained.

Table 8.3 Number of Cooling Fans to be Used

Maximum Motor 200 V Class 400 V Class
Capacity Heatsink Cooling Heatsink Circulation Heatsink Cooling Heatsink Circulation
(kW) Fan Fan Fan Fan
0.4 - - - -
0.75 - - - -
1.5 - - 1 -
2.2 1 - 1 -
3.7 1 - 1 -
4.0 - 1 -
5.5 2 - 2 1
7.5 2 1 2 1
11 2 - 2 1
15 2 1 2 1
18.5 2 - 2 -
22 2 - 2 -
30 2 1 2 -
37 2 1 2 -
45 2 1 2 -
55 2 1 2 1
75 2 1 2 1
90 2 1 2 1
110 2 1 2 1
132 2 1
160 2 1
185 - 4 2
220 4 2
300 5 2

8-5
 ‹ Cooling Fan Replacement Outline

„200 V and 400 V Class Inverters of 15 kW or Less

A cooling fan is attached to the bottom of the Inverter.
If the Inverter is installed using the mounting holes on the back of the Inverter, the cooling fan can be replaced
without removing the Inverter from the installation panel.

Removing the Cooling Fan

1. Press in on the right and left sides of the fan cover in the direction of arrows 1 and pull the fan out in the
direction of arrow 2.
2. Pull out the cable connected to the fan from the fan cover and disconnect the relay connector.
3. Open the fan cover on the left and right sides and remove the fan cover from the fan.

Mounting the Cooling Fan

1. Attach the fan cover to the cooling fan. Be sure that the airflow direction indicated by the arrows above
faces into the Inverter.
2. Connect the relay connector securely and place the relay connector and cable into the fan cover.
3. Mount the fan cover on the Inverter. Be sure that the tabs on the sides of the fan cover click into place on
the Inverter.

Airflow direction

2
1
Fan cover

Fig 8.1 Cooling Fan Replacement (200 V Class Inverters of 3.7 kW)

8-6
 Maintenance and Inspection

„200 V and 400 V Class Inverters of 18.5 kW or More

A cooling fan is attached to the top panel inside the Inverter.
The cooling fan can be replaced without removing the Inverter from the installation panel.

200 V Class Inverters of 18.5 kW

Removing the Cooling Fan

1. Remove the terminal cover, Inverter cover, Digital Operator, and front cover from the front of the Inverter.
2. Remove the control board bracket to which the boards are mounted. Remove all cables connected to the
controller. The cables connected to the control circuit terminals can be removed at the same time by
removing them together with the control circuit terminal board. (Refer to page 8-21)
3. Remove the cooling fan power cable connector (CN26 and CN27) from the gate drive board positioned at
the back of the control board.
4. Remove the fan cover screws and pull out the fan cover from the Inverter.
5. Remove the cooling fan from the fan cover and replace it with a new one.

Mounting the Cooling Fan

After attaching a new cooling fan, reverse the above procedure to attach all of the components.
When attaching the cooling fan to the mounting bracket, be sure that the airflow faces the top of the Inverter.

Airflow direction

Control board bracket Fan cover

Control board Connector

Gate drive board

Fig 8.2 Cooling Fan Replacement (200 V Class Inverters of 18.5 kW)

8-7
 200 V Class Inverters of 22 kW, 45 kW, 55 kW and 400 V Class Inverters of 18.5 kW to 75 kW

Removing the Cooling Fan

1. Remove the terminal cover, Inverter cover, Digital Operator, and front cover from the front of the Inverter.
2. Pull the cooling fan power cable connector that extends from the fan cover cable hole out of the cooling
fan power relay board.
3. Remove the fan cover screws and pull out the fan cover from the Inverter.
4. Remove the cooling fan from the fan cover and replace it with a new one.

Mounting the Cooling Fan

After attaching a new cooling fan, reverse the above procedure to attach all of the components. Refer to the
next page for attaching the fan cover.
When attaching the cooling fan to the mounting bracket, be sure that the airflow faces the top of the Inverter.

Front cover mounting screws

Front cover

Terminal cover

Terminal cover mounting screws

Circulation fan
mounting screws
Fan cable pullout position
Circulation fan

Airflow direction
Fan support Fan support
mounting screws
Fan support
Airflow
direction

Cooling fans

Fan power relay board

Cooling fans

Cooling fan mounting screws

Cooling fan mounting screws

Fan power cable pullout position

Fig 8.3 Cooling Fan Replacement (200 V Class Inverters of 45 kW and 55 kW)

8-8
 Maintenance and Inspection

Attaching the Fan Cover

1. Tilt the fan cover toward the bottom of the Inverter as shown in Fig 8.4 and insert it to the mounting hole
until it meets with A.

Fan cover

Bottom Inverter

Cooling fan
Top Inverter

Fig 8.4

2. Push the fan cover toward the top of the Inverter.

Fig 8.5

3. Make sure that there is no gap between the fan cover and A. Then screw it in place with the three screws.

Make sure that

there is no gap.

NG
A
A

Fig 8.6

8-9
 200 V Class Inverters of 30 kW and 37 kW

Removing the Cooling Fan

1. Remove the terminal cover, Inverter cover, Digital Operator, and front cover from the front of the Inverter.
2. Remove the panel to which the control board, the gate drive board, and the cooling fan power relay board
are mounted. Remove any cables that are connected to the control board, the gate drive board, and the
cooling fan power relay board. The cable that is connected to the control circuit terminals can be removed
together with the control circuit terminal board. (Refer to page 8-21)
3. Remove the fan cover screws and pull out the fan cover from the Inverter.
4. Remove the cooling fan from the fan cover and replace it with a new one.

Mounting the Cooling Fan

After attaching a new cooling fan, reverse the above procedure to attach all of the components.
When attaching the cooling fan to the mounting bracket, be sure that the airflow faces the top of the Inverter.

Fan support mounting screws

Fan cover Panel mounting screws

Front cover mounting screws Cooling fan power relay board

Gate drive
board

Front cover
Panel
mounting
screws

Capacitor

Terminal cover

Terminal
board
Terminal cover mounting screws

Circulation fan mounting screws

Pay attention to
the protruding part Circulation fan
of the fan cable. Cooling fans

Airflow direction

Cooling fan
mounting screws
Fan cover

Fig 8.7 Cooling Fan Replacement (200 V Class Inverters of 30 kW and 37 kW)

8-10
 Maintenance and Inspection

200 V Class Inverters of 75 kW

Removing the Cooling Fan

1. Remove the terminal cover, Inverter cover, Digital Operator, and front cover from the front of the Inverter.
2. Remove the panel to which the control board, the gate drive board, and the cooling fan power relay board
are mounted. Remove any cables that are connected to the control board, the gate drive board, and the
cooling fan power relay board. The cable that is connected to the control circuit terminals can be removed
together with the control circuit terminal board. (Refer to page 8-21)
3. Remove the fan cover screws and pull out the fan cover from the Inverter.
4. Remove the cooling fan from the fan cover and replace it with a new one.

Mounting the Cooling Fan

After attaching a new cooling fan, reverse the above procedure to attach all of the components.
When attaching the cooling fan to the mounting bracket, be sure that the airflow faces the top of the Inverter.

Front cover mounting screws

Front cover

Terminal cover

Terminal cover mounting screws

Fan cover
mounting screws
Fan power relay board Fan cover
Control board mounting panel
Control board mounting Circulation fan
mounting screws
panel

Control board mounting Circulation fan

panel mounting screws Cooling fan
power connector Cooling fan airflow direction
(CN26)
Fan cover
Gate drive
board

Cooling fan
Control circuit terminal board

Cooling fan mounting screws

Cooling fan
airflow direction
Finger guard

Note: A finger guard is not provided on Inverters with slits.

Fig 8.8 Cooling Fan Replacement (200 V Class Inverters of 75 kW)

8-11
 400 V Class Inverters of 90 kW and 110 kW

Removing the Cooling Fan

1. Remove the terminal cover, Inverter cover, Digital Operator, and front cover from the front of the Inverter.
2. Remove the panel to which the control board, the gate drive board, and the cooling fan power relay board
are mounted. Remove any cables that are connected to the control board, the gate drive board, and the
cooling fan power relay board. The cable that is connected to the control circuit terminals can be removed
together with the control circuit terminal board. (Refer to page 8-21)
3. Remove the fan cover screws and pull out the fan cover from the Inverter.
4. Remove the cooling fan from the fan cover and replace it with a new one.

Mounting the Cooling Fan

After attaching a new cooling fan, reverse the above procedure to attach all of the components.
When attaching the cooling fan to the mounting bracket, be sure that the airflow faces the top of the Inverter.

Front cover mounting screws

Front cover

Terminal cover

Terminal cover mounting screws

Circulation fan
Cooling fan power relay board
Fan cover mounting screws Airflow direction

Circulation fan
mounting screws

Circulation fan
Circulation fan
power connector

Cooling fan mounting screws

Fig 8.9 Cooling Fan Replacement (400 V Class Inverters of 90 kW and 110 kW)

8-12
 Maintenance and Inspection

200 V Class Inverters of 90 kW and 110 kW/400 V Class Inverters of 132 kW and 160 kW

Removing the Cooling Fan

1. Remove the terminal cover, Inverter cover, Digital Operator, and front cover from the front of the Inverter.
2. Remove the panel to which the control board, the gate drive board, and the cooling fan power relay board
are mounted. Remove any cables that are connected to the control board, the gate drive board, and the
cooling fan power relay board. The cable that is connected to the control circuit terminals can be removed
together with the control circuit terminal board. (Refer to page 8-21)
3. Remove the fan cover screws and pull out the fan cover from the Inverter.
4. Remove the cooling fan from the fan cover and replace it with a new one.

Mounting the Cooling Fan

After attaching a new cooling fan, reverse the above procedure to attach all of the components.
When attaching the cooling fan to the mounting bracket, be sure that the airflow faces the top of the Inverter.

Front cover mounting screws Fan cover Fan cover mounting screws

Fan power
relay board
Gate drive
board
Front cover
Control board
Terminal
cover

Terminal cover mounting screws

Circulation fan
Circulation fan mounting screws
Circulation fan
Fan cover mounting screws airflow direction

Fan cover

Fan cover
Fan airflow
direction

Fan power relay board

Fan mounting
screws
Finger guard*1
Cooling fan

Fan ground cable*2

* 1. There is no finger guard mounted to the fan for some capacities. (There is a guard on the Inverter side.)
* 2. There is no fan ground cable for the capacities without a finger guard.
Fig 8.10 Cooling Fan Replacement (200 V Class Inverters of 90 kW and 110 kW)

8-13
 400 V Class Inverters of 185 kW and 220 kW

Removing the Cooling Fan

1. Remove the terminal cover and top and bottom front covers from the front of the Inverter.
2. Remove any cables that are connected to the cooling fan power relay board.
3. Remove the fan cover screws and pull out the fan covers from the Inverter.
4. Remove the cooling fan from the fan cover and replace it with a new one.

Mounting the Cooling Fan

After attaching a new cooling fan, reverse the above procedure to attach all of the components.
When attaching the cooling fan to the fan cover, be sure that the airflow faces the top of the Inverter.
Make sure that the fan cable and the fan ground cable are not tangled or pinched.

Fan power relay

Fan cover board Fan cover
Front cover mounting screws

Top front
cover

Terminal
Bottom cover
front
cover

Terminal cover mounting screws

Fan cable
Fan cover mounting screws Fan ground
cable
Enlarged view

Fan airflow
Fan cover mounting screws direction
Colling fan
Cooling fan mounting screws
Finger guard

Fig 8.11 Cooling Fan Replacement (400 V Class Inverters of 185 kW and 220 kW)

8-14
 Maintenance and Inspection

400 V Class Inverters of 300 kW

Removing the Cooling Fan

1. Remove the terminal cover, Inverter cover, Digital Operator, and front cover from the front of the Inverter.
2. Remove any cables that are connected to the cooling fan power relay board. The cable that is connected to
the terminal board can be removed together with the terminal board.
3. Remove the fan unit screws and pull out the fan units from the Inverter.
4. Replace the fan units with new ones.
And, remove the screws for the fan power relay board and attach this board to the new unit.

Mounting the Cooling Fan

After attaching a new cooling fan unit, reverse the above procedure to attach all of the components.

Front cover mounting screws Fan power relay

board Fan cover
Fan cover

Top front
cover

Bottom
front Terminal
cover cover

Terminal cover mounting screws

Relay board mounting screws

Fan cover mounting screws Fan power relay
board
Enlarged
view

Fan cover mounting screws

Fan units
Fan airflow
derection

Fig 8.12 Cooling Fan Replacement (400 V Class Inverters of 300 kW)

8-15
 ‹ Circulation Fan Replacement Outline
With some capacities, there is a small fan installed inside the Inverter for the purpose of increasing circulation
in areas where heat has built up. These fans have built-in fan sensors that output an alarm when the rotation
rate of the fan drops to indicate that replacement is necessary.

„200 V Class Inverters of 7.5 kW/400 V Class Inverters of 5.5 kW and 7.5 kW
The circulation fan is installed behind the control circuit terminal board inside the Inverter.
The circulation fan can be replaced by removing the control circuit terminal board.

Removing the Circulation Fan

1. Remove the Digital Operator, the terminal cover, and the front cover.
2. Remove the control circuit terminal board. Remove the cables connected to the terminals if necessary.
3. While pushing the two tabs (A) in direction 1, pull the fan out in direction 2.
4. Remove the relay connector connected to the fan.

Mounting the Circulation Fan

Reverse the above procedure to mount the fan.
Be sure to mount the fan so that the air flows towards the top of the Inverter (direction indicated by the arrow).
Mount the fan securely using the tabs (A).
Confirm that there are no cables in contact with the fan’s rotating parts.

Control Board
2
1

Airflow direction

Tabs (A)
Circulation fan

Inverter with Control Circuit Terminal Board Removed

Fig 8.13 Circulation Fan Replacement (200 V Class Inverters of 7.5 kW/400 V Class Inverters of 5.5 kW and 7.5 kW)

8-16
 Maintenance and Inspection

„200 V Class Inverters of 15 kW/400 V Class Inverters of 11 kW and 15 kW

The circulation fan is installed at the top-left corner of the Inverter interior.

Removing the Circulation Fan

1. Remove the Digital Operator, the terminal cover, and the front cover.
2. While pushing the relay connector tab (A) in direction 1, pull the relay connector out in direction 2.
3. While pushing the fan tabs (B) in direction 3, pull the fan out in direction 2.
4. Remove the relay connector connected to the fan.

Mounting the Circulation Fan

Reverse the above procedure to mount the fan.
Be sure to mount the fan so that the air flows towards the bottom of the Inverter (direction indicated by the
arrow).
Mount the fan securely using the fan tabs (B).
Confirm that there are no cables in contact with the fan’s rotating parts.

4
Circulation fan
2 1
Relay connector tab (A)
Fan tabs (B)

3
Airflow
direction

Fig 8.14 Circulation Fan Replacement (200 V Class Inverters of 15 kW/400 V Class Inverters of 11 kW and 15 kW)

„200 V Class Inverters of 30 kW or More/400 V Class Inverters of 55 kW or More

The circulation fan is installed in front of the fan cover inside the Inverter. Remove the circulation fan using
the procedure for replacing the cooling fan and replace it with the new fan. (The installation position for 200 V
Class Inverters of 75 kW is different.)

200 V Class Inverters of 75 kW

The circulation fan is installed behind the control board mounting panel. Do not subject the fan to shock dur-
ing replacement.

Removing the Circulation Fan

1. Remove the terminal cover, the Inverter cover, the Digital Operator, and the control board cover.

8-17
 2. Pull out the cables connected to the control circuit terminal board, the gate drive board, and the cooling fan
power relay board.
3. Remove the control board mounting panel.
4. Replace the circulation fan installed behind the control board mounting panel.

Mounting the Circulation Fan

Reverse the above procedure to mount the fan.
Be sure to mount the fan so that the air flows in the direction indicated by the arrow in the corresponding dia-
gram.
Confirm that there are no cables in contact with the fan’s rotating parts.
Refer to Fig 8.8 Cooling Fan Replacement (200 V Class Inverters of 75 kW) for details.

8-18
 Maintenance and Inspection

400 V Class Inverters of 185 kW and 220 kW

Two circulation fans are installed as described in the following sections.

Removing the Circulation Fan

1. Remove the terminal cover and top and bottom front covers.
2. Unscrew the frame fixing screws and take off the frame.
3. Remove the relay connector connected to the fan.
4. Remove the fan cover mounting screws and pull the fan cover out.
5. Remove the fan from the fan cover and replace it with a new one.

Mounting the Circulation Fan

Reverse the above procedure to mount the fan.
Be sure to mount the fan so that the air flows in the direction indicated by the arrow in the corresponding dia-
gram.
Confirm that there are no cables in contact with the fan’s rotating parts.
Fan cable
Fix the fan cable with lnsulok ties

Frame
Frame fixing screws
Fan airflow
direction
Enlarged view

Fan cover mounting screws

Circulation fan

Fan airflow
direction

Fan cover mounting

screws

Enlarged view

Fan cable

Fig 8.15 Circulation Fan Replacement (400 V Class Inverters of 185 kW and 220 kW)

8-19
 400 V Class Inverters of 300 kW
Two circulation fans are installed as described in the following sections.

Removing the Circulation Fan

1. Remove the terminal cover and top and bottom front covers.
2. Unscrew the frame fixing screws and takeoff the frame.
3. Remove the relay connector connected to the fan.
4. Remove the fan cover mounting screws and pull the fan cover out.
5. Remove the fan from the fan cover and replace it with a new one.

Mounting the Circulation Fan

Reverse the above procedure to mount the fan.
Be sure to mount the fan so that the air flows in the direction indicated by the arrow in the corresponding dia-
gram.
Confirm that there are no cables in contact with the fan’s rotating parts.
Fan cable
Fix the fan cable with Insulok ties
Frame
Frame fixing screws Fan airflow
direction

Enlarged view

Fan cover mounting screws

Circulation fan

Fan airflow
direction

Enlarged view
Fix the fan cable
with Insulok ties

Fan cable

Fan cover mounting scerws

Fig 8.16 Circulation Fan Replacement (400 V Class Inverters of 300 kW)

8-20
 Maintenance and Inspection

‹ Removing and Mounting the Control Circuit Terminal Board

The control circuit terminal board can be removed and mounted without disconnecting the cables.

Always confirm that the charge indicator is not lit before removing or mounting the control circuit terminal
board.

IMPORTANT

„Removing the Control Circuit Terminal Board

1. Remove the Digital Operator and front cover.
2. Remove the connecting line connectors connected to FE and NC on the control circuit terminal board.
3. Loosen the mounting screws (1) on the left and right sides of the control terminals until they are free. (It is
not necessary to remove these screws completely. They are self-rising.)
4. Pull the terminal board out sideways (in direction 2) with the screws sticking out from the board.

„Mounting the Control Circuit Terminal Board

Reverse the removal procedure to mount the terminal board.
Confirm that the control circuit terminal board and the control board properly meet at connector CN5 before
pressing in on the board.
The connector pins may be bent if the board is forced into place, possibly preventing correct Inverter opera-
tion.

Removing and Mounting the

Control Circuit Terminal Board

FE NC

Fig 8.17 Removing the Control Circuit Terminal Board

8-21
 Specifications
This chapter describes the basic specifications of the Inverter and specifications for options and
peripheral devices.

Standard Inverter Specifications ..................................9-2

Specifications of Options and Peripheral Devices .......9-6
 Standard Inverter Specifications
The standard Inverter specifications are listed by capacity in the following tables.

‹ Specifications by Model
Specifications are given by model in the following tables.

„200 V Class

Table 9.1 200 V Class Inverters

Model Number CIMR-G7B † 20P4 20P7 21P5 22P2 23P7 25P5 27P5 2011 2015 2018 2022 2030 2037 2045 2055 2075 2090 2110
Max. applicable motor output
0.4 0.75 1.5 2.2 3.7 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90 110
(kW)
Rated input current (A) 3.8 7.2 9.6 14.4 22 32 40 59 79 88 106 143 176 201 246 330 394 457
Rated output capacity
1.2 2.3 3.0 4.6 6.9 10 13 19 25 30 37 50 61 70 85 110 140 160
(kVA)
Output ratings

Rated output current (A) 3.2 6 8 12 18 27 34 49 66 80 96 130 160 183 224 300 358 415
3-phase; 200, 208, 220, 230, or 240 VAC
Max. output voltage (V)
(Proportional to input voltage.)
Max. output frequency
Frequencies supported up to 400 Hz using constant setting
(Hz)
Rated voltage (V)
3-phase, 200/208/220/230/240 VAC, 50/60 Hz*2
Power supply characteristics

Rated frequency (Hz)

Allowable voltage fluctua-
+ 10%, - 15%
tion

Allowable frequency fluc-

±5%
tuation

Measures for DC reactor Optional Built in

power supply 12-phase rec-
harmonics tification
Not possible Possible*3

* 1. The maximum applicable motor output is given for a standard 4-pole Yaskawa motor. When selecting the actual motor and Inverter, be sure that the Inverter's
rated current is applicable for the motor's rated current.
* 2. The voltage of the cooling fan for 200 V Class Inverters of 30 kW is three-phase, 200, 208, or 220 V at 50 Hz or 200, 208, 220, or 230 V at 60 Hz.
* 3. A 3-wire transformer is required on the power supply for 12-phase rectification.

9-2
 Standard Inverter Specifications

„400 V Class
Table 9.2 400 V Class Inverters
Model Number CIMR-G7B † 40P4 40P7 41P5 42P2 43P7 45P5 47P5 4011 4015 4018
Max. applicable motor output
0.4 0.75 1.5 2.2 3.7 5.5 7.5 11 15 18.5
(kW) *1
Rated input current (A) 2.2 4.1 5.8 7.4 10.8 18 25 32 40 46
Rated output capacity
1.4 2.6 3.7 4.7 6.9 11 16 21 26 32
Output ratings

(kVA)
Rated output current (A) 1.8 3.4 4.8 6.2 9 15 21 27 34 42
Max. output voltage (V) 3-phase; 380, 400, 415, 440, 460, or 480 VAC (Proportional to input voltage.)
Max. output frequency Frequencies supported up to 400 Hz using constant setting
(Hz)
Power supply characteristics

Rated voltage (V)

3-phase, 380, 400, 415, 440, 460 or 480 VAC, 50/60 Hz
Rated frequency (Hz)

Allowable voltage fluctua-

+ 10%, - 15%
tion

Allowable frequency fluc-

±5%
tuation

Measures for DC reactor Optional Built in

power supply 12-phase rec-
harmonics tification
Not possible Possible*2

Model Number CIMR-G7B † 4022 4030 4037 4045 4055 4075 4090 4110 4132 4160 4185 4220 4300
Max. applicable motor output
22 30 37 45 55 75 90 110 132 160 185 220 300
(kW)*1
Rated input current (A) 57 72 88 107 141 182 215 264 297 332 407 495 666
Rated output capacity
40 50 61 74 98 130 150 180 210 230 280 340 460
Output ratings

(kVA)
Rated output current (A) 52 65 80 97 128 165 195 240 270 302 370 450 605
Max. output voltage (V) 3-phase, 380, 400, 415, 440, 460, or 480 VAC (Proportional to input voltage.)
Max. output frequency Frequencies supported up to 400 Hz using constant setting
(Hz)

Max. voltage (V)

Power supply characteristics

3-phase, 380, 400, 415, 440, 460, or 480 VAC, 50/60 Hz

Rated frequency (Hz)

Allowable voltage fluctua-

+ 10%, - 15%
tion

Allowable frequency fluc-

±5%
tuation

Measures for DC reactor Built in

power supply 12-phase rec-
harmonics tification Possible*2

* 1. The maximum applicable motor output is given for a standard 4-pole Yaskawa motor. When selecting the actual motor and Inverter, be sure that the Inverter's
rated current is applicable for the motor's rated current.
* 2. A 3-wire transformer (optional) is required on the power supply for 12-phase rectification.

9-3
 ‹ Common Specifications
The following specifications apply to both 200 V and 400 V Class Inverters.

Table 9.3 Common Specifications

Model Number
Specification
CIMR-G7B †
Sine wave PWM
Control method
Flux vector control, open-loop vector 1/2 control, V/f control, V/f with PG control (switched by constant setting)
Torque characteristics 150%/0.3 Hz (Open-loop vector 2 control), 150%/0 min−1 (Flux vector control)*1
Speed control range 1:200 (Open-loop vector 2 control), 1:1000 (Flux vector control)*1
Speed control accuracy*4 ±0.2% (Open-loop vector 2 control, 25°C ± 10°C), ±0.02% (Flux vector control, 25°C ± 10°C)
Speed control response 10 Hz (Open-loop vector 2 control), 30 Hz (Flux vector control)
Torque limits Provided for vector control only (4 quadrant steps can be changed by constant settings.)
Torque accuracy ±5%
Frequency control range 0.01 to 400 Hz*3
Frequency accuracy (tem- Digital references: ± 0.01% (-10°C to +40°C)
Control characteristics

perature characteristics) Analog references: ±0.1% (25°C ±10°C)

Frequency setting resolu-
Digital references: 0.01 Hz, Analog references: 0.03 Hz/60 Hz (11 bit with no sign)
tion
Output frequency resolu-
0.001 Hz
tion
Overload capacity and
150% of rated output current per minute*5 *8
maximum current*2
Frequency setting signal -10 to 10 V, 0 to 10 V, 4 to 20 mA, pulse train
Acceleration/Decelera-
0.01 to 6000.0 s (4 selectable combinations of independent acceleration and deceleration settings)
tion time
Approximately 20% (Approximately 125% with Braking Resistor option, braking transformer built into 200 V and 400 V Class
Braking torque
Inverters for 15 kW or less.)*2
Restarting for momentary power loss, speed searches, overtorque detection, torque limits, 16-speed control (maximum), accelera-
tion/deceleration time changes, S-curve acceleration/deceleration, 3-wire sequence, autotuning (rotational or stationary), dwell
functions, cooling fan ON/OFF control, slip compensation, torque compensation, jump frequencies, upper and lower limits for
Main control functions
frequency references, DC braking for starting and stopping, high-slip braking, PID control (with sleep function), energy-saving
control, MEMOBUS communications (RS-485/422, 19.2 kbps maximum), fault reset, function copying, droop control (flux vec-
tor control only) torque control, speed/torque control switching, etc.
Motor protection Protection by electronic thermal overload relay.
Instantaneous overcurrent
Stops at approx. 200% of rated output current.
protection
Fuse blown protection Stops for fuse blown.
Overload protection 150% of rated output current per minute
200 Class Inverter: Stops when main-circuit DC voltage is approximately above 410 V.
Protective functions

Overvoltage protection
400 Class Inverter: Stops when main-circuit DC voltage is approximately above 820 V.
200 Class Inverter: Stops when main-circuit DC voltage is approximately below 190 V.
Undervoltage protection
400 Class Inverter: Stops when main-circuit DC voltage is approximately below 380 V.
Momentary power loss Stops for 15 ms or more.
ridethrough *7 With a suitable constant setting, operation can be continued if power is restored within 2 s.
Cooling fin overheating Protection by thermistor.
Stall prevention Stall prevention during acceleration, deceleration, or running.
Grounding protection*6 Protection by electronic circuits. (Overcurrent level)
Charge indicator Lit when the main circuit DC voltage is approx. 50 V or more.
Ambient operating tem- -10°C to 40°C (Enclosed wall-mounted type)
perature 10°C to 45°C (Open chassis type)
Ambient operating humid-
95% max. (with no condensation)
ity
Storage temperature - 20°C to + 60°C (short-term temperature during transportation)
Environment

Application site Indoor (no corrosive gas, dust, etc.)

Altitude 1000 m max.
200 V Class Inverters of 0.4 to 37 kW and 400 V Class Inverters of 0.4 to 45 kW
10 to 20 Hz: 9.8 m/s2
20 to 55 Hz: 5.9 m/s2
Vibration
200 V Class Inverters of 45 to 110 kW and 400 V Class Inverters of 55 to 300 kW
10 to 20 Hz: 9.8 m/s2
20 to 55 Hz: 2.0 m/s2

* 1. Rotational autotuning must be performed to ensure obtaining the specifications given for flux or open-loop vector 1/2 control.

9-4
 Standard Inverter Specifications

* 2. When connecting a Braking Resistor or Braking Resistor Unit, set L3-04 (Stall prevention selection during deceleration) to 0 (disabled). Stopping may not be pos-
sible in the specified deceleration time if this function is not disabled.
* 3. The maximum output frequency for open-loop vector 2 control is 132 Hz.
* 4. The speed control accuracy depends on the installation conditions and type of motor used. Contact your Yaskawa representative for details.
* 5. Derating is required for applications that use repetitive loads. (Refer to page 10-6 for details.)
* 6. The ground fault here is one which occurs in the motor wiring while the motor is running. A ground fault may not be detected in the following cases.
y A ground fault with low resistance which occurs in motor cables or terminals.
y A ground fault occurs when the power is turned ON.
* 7. Attach a Backup Capacitor Unit for Momentary Power Loss if compensation for power interruptions of up to 2.0 seconds is required for 200 V/400 V Class
Inverters with outputs of 0.4 to 7.5 kW.
* 8. If running at a speed of 6 Hz or less, the overload protection function can operate even if running within 150% of rated output current per minute.

9-5
 Specifications of Options and Peripheral Devices
The following options and peripheral devices can be used for the Inverter. Select them according to the
application.

Table 9.4 Options and Peripheral Devices

Purpose Name Model (Code) Descriptions
MCCB or Ground Always connect a breaker to the power supply line to protect
Protect Inverter wiring NF† Inverter wiring. Use a ground fault interrupter suitable for high
Fault Interrupter*1 frequencies. Power supply

Prevents burning when

Magnetic Install to prevent the braking resistor from burning out when
a Braking Resistor is SC series
Contactor one is used. Always attach a surge absorber to the coil. Molded-case
used. circuit breaker
or ground fault
Absorbs surge from the magnetic contactor and control relays.
Contains switching interrupter
Surge Absorber DCR2-† Connect surge absorbers to all magnetic contactors and relays
surge
near the Inverter.
Isolates the I/O signals of the Inverter and is effective against Magnetic con-
Isolates I/O signals Isolator DGP† tactor (MC)
inductive noise.
Used to improve the input power factor of the Inverter. All AC reactor for power
Improve the input Inverters of 18.5 kW or higher contain built-in DC reactors. factor improvement
DC Reactor UZDA-†
power factor of the These are optional for Inverters of 15 kW or less. Install DC
AC Reactor UZBA-†
Inverter and AC reactors for applications with a large power supply
capacity (600 kVA or higher).
Reduces noise coming into the Inverter from the power supply
LNFD-† Zero phase reactor
Input Noise Filter line and to reduce noise flowing from the Inverter into the
FN-†
power supply line. Connect as close to the Inverter as possible.
F6045GB Braking resistor

(FIL001098)
Reduce the affects of Finemet zero- Input noise filter
phase reactor to Reduces noise from the line that sneaks into the Inverter input
radio and control device F11080GB
reduce radio power system. Insert as close to the Inverter as possible.
noise (FIL001097)
Can be use on both the input side and output side.
noise*2
F200160BP
(300-001-041) Inverter
Output Noise Fil- Reduces noise generated by the Inverter. Connect as close to
LF-†
ter the Inverter as possible. Varispeed F7

ERF-150WJ†† Consumes the regenerative motor energy with a resistor to

Braking Resistor DC reactor
(R00††††) reduce deceleration time (use rate: 3% ED). for power
factor
Enable stopping the Braking Resistor LKEB-† Consumes the regenerative motor energy with a resistor to improvement
machine in a set time Unit (75600-K†††0) reduce deceleration time (use rate: 10% ED). Ground
Output noise filter
CDBR-† Used with a Braking Resistor Unit to reduce the deceleration
Braking Unit
(72600-R†††0) time of the motor.
Allows frequency reference settings and ON/OFF operation Zero phase
VS Operator
JVOP-95•† control to be performed by analog references from a remote reactor
(small plastic
(73041-0905X-†) location (50 m max.).
Operator)
Frequency counter specifications: 60/120 Hz, 90/180Hz
Allows frequency reference settings and ON/OFF operation
VS Operator
Operates the Inverter JVOP-96•† control to be performed by analog references from a remote
(Standard steel-
externally (73041-0906X-†) location (50 m max.).
plate Operator) Motor
Frequency counter specifications: 75 Hz, 150 Hz, 220 Hz
Ground
1 m cable: (72606-
Digital Operator WV001) Extension cable to use a Digital Operator remotely.
Connection Cable 3 m cable: (72606- Cable length: 1 m or 3 m
WV003)
Controls an Inverter VS System Mod- A system controller that can be match to the automatic control
JGSM-†
system ule system to produce an optimum system configuration.
Provides Inverter Momentary Power
P00†0 Handles momentary power losses for the control power supply
momentary power loss Loss Recovery
(73600-P00†0) for models 7.5 kW or less (maintains power for 2 s).
recovery time Unit
Frequency Meter DCF-6A
Frequency Setter RV30YN20S (2 kΩ)
Set/monitor frequen- Devices to set or monitor frequencies externally.
cies and voltages exter- Frequency Setter
CM-3S
nally. Knob
Measures the output voltage externally and designed for use
Output Voltmeter SCF-12NH
with a PWM Inverter.
Variable Resistor
2 kΩ (ETX003270) Connected to the control circuit terminals to input a frequency
Board for Fre-
Correct frequency refer- quency Reference 20 kΩ (ETX003120) reference.
ence input, frequency
meter, ammeter scales Frequency Meter
Scale Correction (RH000850) Calibrates the scale of frequency meters and ammeters.
Resistor

* 1. Use a ground fault interrupter with a current sensitivity of 200 mA minimum and an operating time of 0.1 s minimum to prevent operating errors. The interrupter
must be suitable for high-frequency operation.
Example: NV series by Mitsubishi Electric Corporation (manufactured in or after 1988)
EG, SG series by Fuji Electric Co., Ltd. (manufactured in or after 1984)
* 2. The finement zero-phase reactor is manufactured by Hitachi Metals.

9-6
 Specifications of Options and Peripheral Devices

The following option boards are available

Table 9.5 Option Boards
Code Num- Document
Type Name Function
ber Number
Enables high-precision, high-resolution setting of analog
Analog Ref- speed references.
73600- TOE-C736-
erence Board • Input signal ranges: 0 to 10 V (20 kΩ), 1 channel
C001X 30.13
AI-14U 4 to 20 mA (250 Ω), 1 channel
• Input resolution: 14-bit (1/16384)

Enables high-precision, high-resolution setting of analog

Analog Ref- speed references.
73600- TOE-C736-
erence Board • Input signal ranges: -10 to 10 V (20 kΩ)
Speed C002X 30.14
AI-14B 4 to 20 mA (500 Ω), 3 channels
(Fre-
• Input resolution: 13-bit + sign (1/8192)
quency)
Refer-
Enables 8-bit digital setting of speed references.
ence
Digital Refer- • Input signal: 8-bit binary
Option 73600- TOE-C736-
Boards ence Board 2-digit BCD + sign signal + set signal
C003X 30.15
DI-08 • Input voltage: +24 V (isolated)
• Input current: 8 mA

Enables 16-bit digital setting of speed references.

• Input signal: 16-bit binary
Digital Refer-
73600- 4-digit BCD + sign signal + set signal TOE-C736-
ence Board
C016X • Input voltage: +24 V (isolated) 40.7
Built-in DI-16H2
• Input current: 8 mA
(con-
With 16-bit/12-bit switch.
nect to
con- Converts analog signals to monitor the Inverter's output status
nector) (output frequency, output current, etc.) to absolute values and
Analog Mon-
73600- outputs them. TOE-C736-
itor Board
D001X • Output resolution: 8 bits (1/256) 30.21
AO-08
• Output voltage: 0 to +10 V (not insulated)
• Output channels: 2 channels

Output analog signals to monitor the Inverter's output status

Analog Mon- (output frequency, output current, etc.).
73600- TOE-C736-
itor Board • Output resolution: 11 bits (1/2048) + sign
Moni- D002X 30.22
AO-12 • Output voltage: -10 to +10 V (not insulated)
toring
Option • Output channels: 2 channels
Boards
Outputs isolated digital signals to monitor the Inverters oper-
ating status (alarm signals, zero-speed detection, etc.)
Digital Out-
73600- Output form: Photocoupler output, 6 channels TOE-C736-
put Board
D004X (48 V, 50 mA max.) 30.24
DO-08
Relay contact outputs, 2 channels
(250 VAC: 1 A max., 30VDC: 1 A max.)

2C-Relay
73600- Provides two multi-function outputs (DPDT relay contacts) in TOE-C736-
Output Board
D007X addition to those provided by the Inverter. 40.8
DO-02C

9-7
 Table 9.5 Option Boards (Continued)
Code Num- Document
Type Name Function
ber Number
Used for V/f with PG control. Speed feedback is performed
using the PG attached to the motor to compensate for speed
fluctuations caused by slipping.
73600- • A-phase pulse (single pulse) input (voltage, complemen- TOE-C736-
PG-A2
A012X tary, open-collector input) 40.1
• Maximum input frequency: 32767 Hz
• Pulse monitor output: +12 V, 20 mA
(PG power supply output: +12 V, 200 mA max.)

• Used for V/f control with PG and flux vector control.

Built-in • A-, B-phase input (complimentary input)
PG 73600- TOE-C736-
(con- PG-B2 • Maximum input frequency: 32767 Hz
Speed A013X 40.2
nect to • Pulse monitor output: Open-collector
Con- (PG power supply output: +12 V, 200 mA max.)
con-
trol
nector) • Differential input.
Boards
• A-phase pulse (differential pulse) input, for V/f control
73600- • Maximum input frequency: 300 kHz TOE-C736-
PG-D2
A014X • Input: Conforms to RS-422 40.3
• Pulse monitor output: RS-422
(PG power supply output: +5 or +12 V, 200 mA max.)

• A-, B-, Z-phase pulse (differential pulse) input

• Maximum input frequency: 300 kHz
73600- TOE-C736-
PG-X2 • Input: Conforms to RS-422
A015X 40.4
• Pulse monitor output: RS-422
(PG power supply output: +5 or +12 V, 200 mA max.)

9-8
 Specifications of Options and Peripheral Devices

Table 9.5 Option Boards (Continued)

Code Num- Document
Type Name Function
ber Number
DeviceNet
Used to communicate with an Inverter from a host computer
Communica-
73600- using DeviceNet communications to start/stop Inverter opera-
tions Inter- -
C021X tion, read/set parameters, and read/set monitor constants (out-
face Board
put frequencies, output currents, etc.).
SI-N

ProfiBus-DP
Communica-
73600-
tions Inter-
C022X
face Board Used to communicate with an Inverter from a host computer
SI-P using ProfiBus-DP communications to start/stop Inverter
-
ProfiBus-DP operation, read/set parameters, and read/set monitor constants
Communica- (output frequencies, output currents, etc.).
73600-
tions Inter-
C033X
face Board
SI-P1

InterBus-S
Used to communicate with an Inverter from a host computer
Communica-
using InterBus-S communications to start/stop Inverter opera-
tions Inter- * -
tion, read/set parameters, and read/set monitor constants (out-
face Board
put frequencies, output currents, etc.).
SI-R

CANopen
Used to communicate with an Inverter from a host computer
Communica-
using CANopen communications to start/stop Inverter opera-
tions Inter- * -
tion, read/set parameters, and read/set monitor constants (out-
Built-in Com- face Board
put frequencies, output currents, etc.).
SI-S1
(con- muni-
nected cations ControlNet
to con- Option Used to communicate with an Inverter from a host computer
Communica-
nector) Boards using ControlNet communications to start/stop Inverter opera-
tions Inter- * -
tion, read/set parameters, and read/set monitor constants (out-
face Board
put frequencies, output currents, etc.).
SI-U

CC-Link
Used to communicate with an Inverter from a host computer
Communica-
73600- using CC-Link communications to start/stop Inverter opera-
tions Inter- -
C032X tion, read/set parameters, and read/set monitor constants (out-
face Board
put frequencies, output currents, etc.).
SI-C

LONWORKS
Used to communicate with an Inverter from a host computer
Communica-
73600- using LONWORKS communications to start/stop Inverter
tions Inter- -
C035X operation, read/set parameters, and read/set monitor constants
face Board
(output frequencies, output currents, etc.).
SI-J

LONWORKS Used to communicate with an Inverter from a host computer

Communica- using LONWORKS communications to start/stop Inverter
73600-
tions Inter- operation, read/set parameters, and read/set monitor constants -
C034X
face Board (output frequencies, output currents, etc.).
SI-W1 With Display Data Channel (DDC) function.

MECHA-
TROLINK- Used to communicate with an Inverter from a host computer
Communi- using MECHATROLINK communications to start/stop
cations Inter- 100-017-994 -
Inverter operation, read/set parameters, and read/set monitor
face Board constants (output frequencies, output currents, etc.).
SI-T
* Under development.

9-9
 Appendix
This chapter provides precautions for the Inverter, motor, and peripheral devices and also pro-
vides lists of constants.

Varispeed G7 Control Methods..................................10-2

Inverter Application Precautions ................................10-6
Motor Application Precautions ...................................10-9
Conformance to UL Standard .................................. 10-11
Conformance to CE Markings..................................10-13
Wiring Examples......................................................10-20
User Constants ........................................................10-29

10
 Varispeed G7 Control Methods
Details of the Varispeed G7-Series Inverter control methods and their features are provided in this section.

‹ Control Methods and Features

Varispeed G7-Series Inverters support the following five control methods, allowing the selection of a control
method to suit the required purpose. Table 10.1 provides an overview of the control methods and their fea-
tures.

Table 10.1 Overview and Features of Control Methods

V/f Control with Open-loop Vec- Flux Vector Con- Open-loop Vec-
Control Method V/f Control
PG tor 1 Control trol tor 2 Control
A1-02 = 2
Constant Setting A1-02 = 0 A1-02 = 1 A1-02 = 3 A1-02 = 4
(factory setting)

Current vector
Voltage/frequency control without a
fixed ratio control Current vector PG using a high-
Voltage/frequency Current vector
Basic Control with speed com- control without a performance mag-
fixed ratio control control with a PG
pensation using a PG netic flux and
PG speed estimator
(software)

Very high-perfor-
mance control
Variable speed
Very high-perfor- without a PG on
Variable speed control, applica-
mance control the motor side
control, particu- Applications tions requiring
with a PG on the (such as simple
larly for control of requiring high- high performance
motor side (sim- servodrives,
multiple motors precision speed without a PG on
Main Applications ple servodrives, torque control, and
with a single control using a PG the motor side,
high-precision torque limiting),
Inverter and for on the machine and for replacing
speed control, and function appli-
replacing existing side open-loop vector
torque control, and cations between
Inverters control of the pre-
torque limiting) flux vector and
vious VS-616G5.
open-loop vector 1
control.

PG Speed Control Board Required (PG-A2 Required (PG-B2

Not required. Not required. Not required.
(Option) or PG-D2). or PG-X2).

Speed Control 1:200 (1:10 on

1:40 1:40 1:100 1:1000
Range*1 regenerative side)

Speed Control
±2 to 3% ±0.03% ±0.2% ±0.02% ±0.2%
Accuracy*2

Basic Speed
Perfor- Approx. 1 Hz Approx. 1 Hz 5 Hz 40 Hz 10 Hz
Response*3
mance
Maximum
Output Fre- 400 Hz 400 Hz 400 Hz 400 Hz 60 Hz, 120 Hz
quency

Starting
150%/3 Hz 150%/3 Hz 150%/1 Hz 150%/0 min−1 150%/0.3 Hz
Torque*4

10-2
 Varispeed G7 Control Methods

Table 10.1 Overview and Features of Control Methods (Continued)

V/f Control with Open-loop Vec- Flux Vector Con- Open-loop Vec-
Control Method V/f Control
PG tor 1 Control trol tor 2 Control
Rotational Rotational Rotational
autotuning, sta- autotuning, sta- autotuning, sta-
Line-to-line resis- Line-to-line resis- tionary autotuning, tionary autotuning, tionary autotuning,
Autotuning tance (Normally tance (Normally stationary stationary stationary
not required.) not required.) autotuning for autotuning for autotuning for
line-to-line resis- line-to-line resis- line-to-line resis-
tance only tance only tance only

Yes (except dur-

ing acceleration/ Yes (except below
Torque Limit- deceleration, minimum fre-
No No below minimum Yes quency and dur-
ing*5 frequency, or dur- ing reverse
ing reverse rota- rotation)
tion)

Yes (except below

Torque Con- minimum fre-
No No No Yes quency and dur-
trol*6 ing reverse
rotation)

Appli- Yes (except for Yes (Except below

cation minimum fre-
Droop Con-
No No No 0 min−1 and dur- quency and dur-
Func- trol*7 ing reverse rota-
tions ing reverse
tion) rotation)

Zero-servo
No No No Yes No
Control*8

Speed Estima-
tion (Detec- Yes (speed detec-
tion) Yes (speed and Yes (speed and Yes (speed and Yes (speed and
tion and rotation
Instantaneous rotation direction rotation direction rotation direction rotation direction
direction estima-
Speed estimation) estimation) detection) estimation)
tion)
Search*9

Automatic
Energy-sav- Yes Yes Yes Yes Yes
ing Control*10

High-slip (Under develop- (Under develop- (Under develop-

Yes Yes
Braking*11 ment) ment) ment)
10
Feed For-
ward Con- No No No Yes Yes
trol*12
* 1. The variable speed control range. (For continuous operation, the motor's temperature rise must be considered.)
* 2. The speed deviation in relation to the maximum speed with a rated load and when the load is stable. (For open-loop vector 1 and 2 control, the motor temperature
must be 25 °C ± 10 °C.)
* 3. The speed response guidelines indicating the extent of the motor's actual speed gain in proportion to the speed reference, which changes in a sinusoidal wave
form, within a range where motor torque does not become saturated.
* 4. A guideline for the motor torque that can be generated when started at a low speed and its output frequency (rotations) at that time.
* 5. This function limits the maximum motor torque to protect the machine and the load.
* 6. This function directly controls the amount of torque being generated at the motor and its rotation direction, e.g., to control force.
* 7. This function controls the amount of motor slip that occurs to prevent mechanical shock, when replacing a torque motor, etc.
* 8. This function performs simple positioning control (servo lock), without using an external positioning control device.
* 9. This function instantaneously estimates (or detects) the speed and rotation direction of a coasting motor, and quickly starts it without subjecting it to shock.
* 10.This function automatically adjusts the voltage applied to the motor to optimize the motor's efficiency with light loads.
* 11.This function improves the deceleration time without using a braking resistor by making the motor winding absorb regenerative power. As a standard, this func-
tion is effective with a motor running on 160 kW or less with a high-inertia load.
* 12.This function enables proportional gain in relation to changes in the speed reference, even for low rigidity (corresponds to the servo's model gain control).
* 13.Set the maximum output frequency (E1-04) for open-loop vector 2 control to 120 Hz max. For torque control on the regenerative side, use in the speed range 1:10.

10-3
 „Application Function Precautions
Observe the following precautions when using the application functions.
• Perform rotational autotuning during trial operation whenever it is possible to separate the motor and
machine. To achieve the characteristics of vector control described in Table 10.1, the control must be
adjusted within a range that the machine will not vibrate after rotational autotuning has been performed.
• With vector control, the motor and Inverter must be connected 1:1. Vector control is not possible when
multiple motors are connected to a single Inverter. Select an Inverter capacity so the rated motor current is
50% to 100% of the rated Inverter current.
• For estimated speed searching, the motor and Inverter must be connected 1:1. The speed search must be
performed at a frequency of 130 Hz or less and with a motor with the same number of frames as or one
frame less than the Inverter capacity.
• During high-slip braking, motor loss increases, so use a high-slip braking frequency of 5% ED or less, and
a braking time of 90 seconds or less. Once high-slip braking has started, the motor cannot be restarted until
it has stopped.
• Feed forward control is a function that improves the proportional gain of the motor speed in relation to the
change in the speed reference. Adjust the response to interference loads using the speed controller (ASR)
constants.
• The torque limit function will not operate during acceleration or deceleration (during soft start transition)
when using a control method such as open-loop vector 1 control. Even if the motor speed drops due to
torque limiting while set to a fixed speed, the speed will not fall below the minimum frequency and the
motor will not slip into reverse rotation. These conditions also apply to open-loop vector 2 control and
other application functions.

„Precautions for Open-loop Vector 2 Control

In open-loop vector 2 control, two speed estimators are switched between and, if used at a maximum fre-
quency exceeding 70 Hz, there may be instances of shock occurring at the switchover. If switching shock is a
problem, reduce the switching frequency (N4-11 and N4-28). If the problem still occurs after making this
adjustment, use open-loop vector 1 control.
Do not use open-loop vector 2 control for elevating machines. Any other control method can be used.

‹ Control Methods and Applications

Application examples for the Inverter control methods are provided here.

„V/f Control (A1-02 = 0)

V/f control is suitable for applications where multiple motors are operated with a single Inverter, such as with
multi-motor drives.

(Thermal relay)

Inverter M1

M2

M3

Fig 10.1

10-4
 Varispeed G7 Control Methods

„V/f Control with PG (A1-02 = 1)

V/f control with a PG enables precise control of machine line speed. Speed control using the speed feedback
of the machine shaft is possible in this mode.

Conveyor
Inverter

PG
PG Speed Control Board
(PG-A2 or PG-D2)

Fig 10.2

„Open-loop Vector Control (A1-02 = 2 or 4)

Open-loop vector control enables the use of high-performance drives without a speed detector. PG (pulse gen-
erator) wiring is not required.

Inverter M

Fig 10.3

„Flux Vector Control (A1-02 = 3)

Flux vector control is suitable for applications using high-precision drives with PG feedback. High-precision
positioning, zero-speed control, and torque control are possible with this mode.

Inverter M

PG

PG Speed Control Board

(PG-B2 or PG-X2)

Fig 10.4

10

10-5
 Inverter Application Precautions
This section provides precautions for selecting, installing, setting, and handling Inverters.

‹ Selection
Observe the following precautions in selecting an Inverter.

„Installing Reactors
A large peak current will flow in the power input circuit when the Inverter is connected to a large-capacity
power transformer (600 kVA or higher) or when switching a phase advancing capacitor. Excessive peak cur-
rent can destroy the convertor section. To prevent this, install a DC or AC reactor (optional) to improve the
power supply power factor.
DC reactors are built into 200 V Class Inverters of 18.5 to 110 kW and 400 V Class Inverters of 18.5 to 300
kW.
If a thyristor convertor, such as a DC drive, is connected in the same power supply system, connect a DC or
AC reactor regardless of the power supply conditions shown in the following diagram.

DC or AC reactor
Power supply Required
capacity (kVA)
DC or AC reactor
Not required

Inverter capacity (kVA)

Fig 10.5

„Inverter Capacity
When connecting special motors or multiple motors in parallel to an Inverter, select the Inverter capacity so
that the rated output current of the Inverter is 1.1 times the sum of all the motor rated currents.

„Applications with Repetitive Loads

Applications with repetitive loads (cranes, elevators, presses, washing machines, etc.) using Inverters require
derating for the repetitive load [reducing carrier frequency and current (changing accel/decel timing, increas-
ing the frame size of the Inverter)]. Refer to Current Alarm Function and Peak Hold Current Monitoring
Function in Chapter 6 to confirm the output current during startup.

„Initial Torque
The startup and acceleration characteristics of the motor are restricted by the overload current ratings of the
Inverter that is driving the motor. The torque characteristics are generally less than those required when start-
ing using a normal commercial power supply. If a large initial torque is required, select an Inverter with a
somewhat larger capacity or increase the capacity of both the motor and the Inverter.

„Emergency Stop
Although the Inverter's protective functions will stop operation when a fault occurs, the motor will not stop
immediately. Always provide mechanical stop and protection mechanisms on equipment requiring an emer-
gency stop.

10-6
 Inverter Application Precautions

„Options
Terminals B1, B2, , 1, 2, 3 are for connecting only the options specifically provided by Yaskawa.
Never connect any other devices to these terminals.

‹ Installation
Observe the following precautions when installing an Inverter.

„Installation in Enclosures
Either install the Inverter in a clean location not subject to oil mist, air-bourne matter, dust, and other contam-
inants, or install the Inverter in a completely enclosed panel. Provide cooling measures and sufficient panel
space so that the temperature surrounding the Inverter does not go beyond the allowable temperature. Do not
install the Inverter on wood or other combustible materials.

„Installation Direction
Mount the Inverter vertically to a wall or other horizontal surface.

‹ Settings
Observe the following precautions when making settings for an Inverter.

„Upper Limits
The Digital Operator can be used to set high-speed operation up to a maximum of 400 Hz (depends on the car-
rier frequency). Incorrect settings can be dangerous. Use the maximum frequency setting functions to set
upper limits. (The maximum output frequency is factory-set to 60 Hz.)

„DC Injection Braking

The motor can overheat if the DC injection braking voltage or braking time is set to a large value.

„Acceleration/Deceleration Times
The motor's acceleration and deceleration times are determined by the torque generated by the motor, the load 10
2
torque, and the load's inertial moment (GD /4). If the stall prevention functions are activated during accelera-
tion or deceleration, increase the acceleration or deceleration time. The stall prevention functions will increase
the acceleration or deceleration time by the amount of time the stall prevention function is active.
To reduce the acceleration or deceleration times, increase the capacity of the motor and Inverter.

10-7
 ‹ Handling
Observe the following precautions when wiring or performing maintenance for an Inverter.

„Wiring Check
The Inverter will be internally damaged if the power supply voltage is applied to output terminal U, V, or W.
Check wring for any mistakes before supplying power. Check all wiring and sequences carefully.

„Magnetic Contactor Installation

Do not start and stop operation frequently with a magnetic contactor installed on the power supply line. Doing
so can cause the Inverter to malfunction. Do not turn the Inverter ON and OFF with a magnetic contactor more
than one time every 30 minutes.

„Setting the Power Supply Voltage Jumper (400 V Class Inverters of 55 kW or Higher)
If the jumper is inserted into a power tap that does not match the actual power supply voltage, the lifetime of
the transformer for the power supply or the wind capacity of the cooling fan may be reduced.
If the jumper is inserted and the voltage setting is too low for the actual power supply, a power surge may
occur on the transformer for the power supply and reduce the lifetime of the transformer.
If the jumper is inserted and the voltage setting is too high for the actual power supply, the wind capacity of
the cooling fan is reduced.
Insert the jumper into the power tap with the voltage setting nearest to the voltage of the actual power supply.
Refer to Chapter 4 Trial Operation for the procedure.

„Maintenance and Inspections

After turn OFF the main circuit power supply, always confirm that the CHARGE indicator is not lit before
performing maintenance or inspections. The voltage remaining in the capacitor may cause electric shock.

10-8
 Motor Application Precautions

Motor Application Precautions

This section provides precautions for motor application.

‹ Using the Inverter for an Existing Standard Motor

When a standard motor is operated with the Inverter, power loss is slightly higher than when operated with a
commercial power supply. Observe the following precautions when using an Inverter for an existing standard
motor.

„Low Speed Ranges

Cooling effects diminish in the low-speed range, resulting in an increase in the motor temperature. Therefore,
the motor torque should be reduced in the low-speed range whenever using a motor not made by Yaskawa. If
100% torque is required continuously at low speed, consider using a special Inverter or vector motor.

„Installation Withstand Voltage

If the input voltage is higher than the motor rated voltage or the wiring distance is long, the motor insulation
voltage must be considered. Contact your Yaskawa representative for details.

„High-speed Operation
When using the motor at a speed higher than the rated speed, problems may arise in dynamic balance and
bearing durability. Contact your Yaskawa representative for details.

„Torque Characteristics
The motor may require more acceleration torque when the motor is operated with the Inverter than when oper-
ated with a commercial power supply. Check the load torque characteristics of the machine to be used with the
motor to set a proper V/f pattern.

„Vibration
The Inverter uses a high carrier PWM to reduce motor vibration. (A constant can be set to select low carrier,
PWM modulation control as well.) When the motor is operated with the Inverter, motor vibration is almost the
same as when operated with a commercial power supply.
Motor vibration may, however, become greater in the following cases.

Resonance with the Natural Frequency of the Mechanical System 10

Take special care when a machine that has been operated at a constant speed is to be operated in variable speed
mode. If resonance occurs, install vibration-proof rubber on the motor base or use the frequency jump function
to skip any frequency resonating the machine.

Imbalanced Rotor
Take special care when the motor is operated at a speed higher than the rated speed.

„Noise
Noise varies with the carrier frequency. At high carrier frequencies, the noise is almost the same when the
motor is operated with a commercial power supply. Motor noise, however, becomes louder when the motor is
operated at a speed higher than the rated speed.

10-9
 ‹ Using the Inverter for Special Motors
Observe the following precautions when using a special motor.

„Pole-changing Motor
The rated input current of pole-changing motors differs from that of standard motors. Select, therefore, an
appropriate Inverter according to the maximum input current of the motor to be used. Before changing the
number of poles, always make sure that the motor has stopped. Otherwise, the overvoltage protective or over-
current protective mechanism will be actuated, resulting in an error.

„Submersible Motor
The rated input current of submersible motors is higher than that of standard motors. Therefore, always select
an Inverter by checking its rated output current. When the distance between the motor and Inverter is long, use
a cable thick enough to connect the motor and Inverter to prevent motor torque reduction.

„Explosion-proof Motor
When an explosion-proof motor is to be used, it must be subject to an explosion-proof test in conjunction with
the Inverter. This is also applicable when an existing explosion-proof motor is to be operated with the Inverter.
Since the Inverter itself is, however, not explosion-proof, always install it in a safe place.

„Gearmotor
The speed range for continuous operation differs according to the lubrication method and motor manufacturer.
In particular, continuous operation of an oil-lubricated motor in the low speed range may result in burning. If
the motor is to be operated at a speed higher than the rated speed, consult with the manufacturer.

„Synchronous Motor
A synchronous motor is not suitable for Inverter control. If a group of synchronous motors is individually
turned ON and OFF, synchronism may be lost.

„Single-phase Motor
Do not use an Inverter for a single-phase motor. The motor should be replaced with a 3-phase motor.

‹ Power Transmission Mechanism (Speed Reducers, Belts, and Chains)

If an oil-lubricated gearbox or speed reducer is used in the power transmission mechanism, oil lubrication will
be affected when the motor operates only in the low speed range. The power transmission mechanism will
make noise and experience problems with service life and durability if the motor is operated at a speed higher
than the rated speed.

10-10
 Conformance to UL Standard

Conformance to UL Standard
To comply with UL standard, follow the appropriate installation instructions.

„Installation Site
Install the Inverter in a pollution degree 2 environment or equivalent.

„Specification of Closed-Loop Connector

The closed-loop connectors must be installed on conductors before installing to terminal blocks.
Use UL Listed closed-loop connectors shown below.

Table 10.2 JST Closed-Loop Connector Model

Inverter JST Kit P/N
Model CIMR-G7B Input Output
27P5 14-5 14-5

2015 38-8 38-8

2018 60-8 38-8

2022 60-8 60-8

2030 80-10 80-10

2037 100-10 100-10

2045 60-10 (2perPh) 60-10 (2perPh)

2055 80-12 (2perPh) 80-10 (2perPh)

2075 150-12 (2perPh) 100-12 (2perPh)

2090 150-12 (2perPh) 150-12 (2perPh)

2110 200-12 (2perPh) 150-12 (2perPh)

4011 8-5 8-5

4015 14-5 14-5

4018 14-6 14-6

4022 22-6 22-6

4030 38-8 22-8

4037 38-8 38-8

4045 60-8 60-8 10

10-11
 „Control Circuit Terminal
A UL Listed, Class 2 power supply must be used for the control circuits. See below table.
.

Table 10.3 Power Supply for Control Circuits

Input/Output Terminal Power Supply
Open Collec- P1, P2, P3, P4
Class 2 power supply
tor Outputs PC, C3, C4

S1, S2, S3, S4,

S5, S6, S7, S8, LVLC power supply when using
Digital Inputs
S9, S10, S11, internal power supply. Class 2
S12, SC power supply when using exter-
RP, +V, -V, A1, nal power supply.
Analog Inputs
A2, A3, AC

„Interrupting Rating
Varispeed G7 is suitable for use on a circuit capable of delivering not more than 100,000 RMS symmetrical
amperes, 240 VAC maximum (200 V Class) and 480 VAC maximum (400 V Class).
Use a circuit breaker or fuses having an interrupting rating not less than 100,000 RMS symmetrical amperes,
600 VAC maximum.

„Motor Overheat Protection

To protect the motor from overheating, set the E2-01 constant in the Inverter to the same value as the level of
the motor rated current.

10-12
 Conformance to CE Markings

Conformance to CE Markings
Points regarding conformance to CE markings are given below.

‹ CE Markings
CE markings indicate conformance to safety and environmental standards that apply to business transactions
(including production, imports, and sales) in Europe. There are unified European standards for mechanical
products (Machine Directive), electrical products (Low Voltage Directive), and electrical noise (EMC Direc-
tive). CE markings are required for business transactions in Europe (including production, imports, and sales).
The Varispeed G7-Series Inverters bear CE markings indicating conformance to the Low Voltage Directive
and the EMC Directive.
• Low Voltage Directive: 2006/95/EC
• EMC Directive: 2004/108/EC
Machinery and installations that incorporate the Inverter are also subject to CE markings. It is ultimately the
responsibility of customers making products incorporating the Inverter to attach CE markings to the finished
products. The customer must confirm that the finished products (machines or installations) conform to the
European Standards.

‹ Requirements for Conformance to CE Markings

„Low Voltage Directive

Varispeed G7-Series Inverters satisfy testing for conformance to the Low Voltage Directive under the condi-
tions described in European Standard EN50178.

Requirements for Conformance to the Low Voltage Directive

Varispeed G7-Series Inverters must satisfy the following conditions in order to conform to the Low Voltage
Directive.
• It must be used under conditions corresponding to overvoltage category 3 or less and pollution degree 2 or
less as specified in IEC664.
• Input fuses:
For details on selecting fuses, refer to Table 10.4 Selection Requirements for Input Fuses with Examples.
• With Inverters CIMR-G7B2018 to 2110 and CIMR-G7B4018 to 4300, an enclosure preventing foreign
matter from entering from the top or front sides is required (IP4X or higher: panel installation).
10

10-13
 Wiring Example
This example shows wiring for conforming to undervoltage reference.
Thermal switch Thermal relay
contact trip contact

Braking Unit 3 4 1 2

(optional) + +0 P

Level
detector
-0 B
Motor
2MCCB Braking Resistor Unit
FU - (optional)
FU Cooling fan
FV
FW *1 FV IM
+1 +3 -
Noise FW
Fuse 1MCCB filter
MC
Inverter U
3-phase power R R/L1 U/T1
200 to 240 V S S/L2 V
CIMR-G7B2018 V/T2 IM
50/60 Hz
T W
T/L3 W/T3
Vm
ON
2MCCB THRX OFF MC

MC SA Forward Run/Stop S1 PG-B2 TA1

Thermal relay trip contact (optional) 1 C
for Braking Resistor Unit 2 H
THRX Reverse Run/Stop S2 3 B
1 2 4 G
SA Thermal switch contact PG
Thermal relay trip contact 5 A
for Braking Unit
for motor cooling fan 3 4 6 F
External fault S3
1 2
TA3 D

Fault reset Shielded twisted-pair

MC TRX S4 TA2 wires
1
SA Multi-step speed reference 1 Pulse monitor output
(Main speed switching) S5 2 Pulse A 30 mA max.
TRX
3

MC 4 Pulse B Wiring d
distance:
MA
Fault contact
reference 2 S6 30 m max.
Multi-step speed
Jog frequency
selection S7
External
Multi-function baseblock command S8 MP Pulse train output
contact inputs
Multi-step speed 0 to 32 kHz (2.2 kΩ)
Factory AC Default: Output
settings
reference 3 S9
frequency
Multi-step speed
reference 4 S10
Ammeter adjustment
Acc/dec time 1 S11 AM 20k Ω
Multi-function analog output 2
Emergency stop -10 to 10 V 2 mA
(NO) S12
- AM +
Default: Output current
0 to +10 V
CN5 (NPN setting) +24V 8mA
Ammeter adjustment
SC FM 20k Ω
Multi-function analog output 1
AC - + -10 to 10 V 2 mA
FM Default: Output frequency
+24V 0 to +10 V

E (G) Shield wire E(G)

connection
terminal *2
Pulse train input MA
RP Master speed MA
Error contact output
pulse train
Frequency setting 0 to 32 kHz (3 kΩ) MB
250 VAC, 10 mA min. 1 A max.
2kΩ adjustment High level: 3.5 to 13.2 V input
MC MC
30 VDC, 10 mA min. 1 A max.
Frequency Frequency setting power
setter +V
3 +15 V, 20 mA
0 to +10V M1
External 2kΩ A1 Master speed reference Multi-function contact output
2
frequency 1 0 to 10 V (20 kΩ)
4 to 20mA P M2 250 VAC, 10 mA min. 1 A max.
A2 Master speed reference
references 30 VDC, 10 mA min. 1 A max.
4 to 20 mA (250 Ω)
Default: Running
[0 to 10 V (20 kΩ) input]
P signal
0 to +10V Multi-function anlog input
A3
0 to 10 V (20 kΩ)
? P1
P AC Factory setting: Open collector 1
0V Not used Default: Zero-
speed Multi-function
open-collector outputs
-V ( -15V 20mA) P2
Open collector 2 48 VDC 50 mA max.
Default: Frequency
Terminating
resistance PC agree signal

R+
R- P3
MEMOBUS Open collector 3
communications S+ Factory setting:
RS-485/422 C3 Inverter operation
ready
S- P4
Open collector 4
Factory setting:
IG C4 minor fault

*3

* 1. The main circuit is separated from the terminal cover for safety reasons.
* 2. The contact output circuit is separated from the main circuit and the control circuit by reinforced insulation.
It can be connected to extra-low voltage circuits or circuits that are 250 VAC 1 A, 30 VDC 1 A or less.
* 3. The control circuit is an extra-low voltage circuit and separated from the main circuit and the contact output circuit by reinforced insulation. Always
connect it to extra-low voltage circuits.
Fig 10.6

10-14
 Conformance to CE Markings

Input Fuses
In order to conform to the Low Voltage Directive, fuses must be provided for inputs. Use UL-compatible input
fuses with ratings higher than the voltages and currents, and fusing I2t specifications within the ranges shown
in the table below.

Table 10.4 Selection Requirements for Input Fuses with Examples

Selection Requirements Input Fuse (Examples)
Inverter Model Fusing
Voltage
Number Voltage Current Fusing I2t
Class Model Number Manufacturer Ratings I2t
CIMR-G7B (V) (A) (A2sec)
(A2sec)
600V
20P4 240 10 12 to 25 A60Q12-2 FERRAZ 17
12A
600V
20P7 240 15 23 to 55 CR2LS-20/UL FUJI 27
12A
250V
21P5 240 20 34 to 98 CR2LS-30/UL FUJI 60
20A
250V
22P2 240 30 82 to 220 CR2LS-50/UL FUJI 200
30A
250V
23P7 240 40 220 to 610 CR2LS-75/UL FUJI 560
50A
250V
25P5 240 50 290 to 1300 CR2LS-75/UL FUJI 560
75A
250V
27P5 240 60 450 to 5000 CR2LS-100/UL FUJI 810
75A
250V
2011 240 90 1200 to 7200 CR2L-125/UL FUJI 1570
100A
250V
2015 240 120 1800 to 7200 CR2L-150/UL FUJI 2260
200 V 125A
Class 250V
2018 240 140 870 to 16200 CR2L-150/UL FUJI 2260
150A
250V
2022 240 160 1500 to 23000 CR2L-200/UL FUJI 4010
150A
250V
2030 240 220 2100 to 19000 CR2L-260/UL FUJI 7320
200A
250V
2037 240 270 2700 to 55000 CR2L-300/UL FUJI 9630
260A
250V
2045 240 300 4000 to 55000 CR2L-300/UL FUJI 9630
300A
250V
2055 240 370 7100 to 64000 CR2L-400/UL FUJI 24000 10
350A
250V
2075 240 500 11000 to 64000 CR2L-500/UL FUJI 40000
450A
250V
2090 240 600 13000 to 83000 CR2L-600/UL FUJI 52000
600A
250V
2110 240 700 13000 to 83000 A50P700-4 FERRAZ 49000
600A

10-15
 Table 10.4 Selection Requirements for Input Fuses with Examples (Continued)
Selection Requirements Input Fuse (Examples)
Inverter Model Fusing
Voltage
Number Voltage Current Fusing I2t
Class Model Number Manufacturer Ratings I 2t
CIMR-G7B (V) (A) (A2sec)
(A2sec)
600V
40P4 480 5 16 to 660 CR6L-20/UL FUJI 26
20A
600V
40P7 480 10 19 to 660 CR6L-20/UL FUJI 26
20A
600V
41P5 480 10 46 to 660 CR6L-30/UL FUJI 59
30A
600V
42P2 480 15 78 to 660 CR6L-50/UL FUJI 317
50A
600V
43P7 480 20 110 to 660 CR6L-50/UL FUJI 317
50A
600V
44P0 480 30 220 to 660 CR6L-50/UL FUJI 317
50A
600V
45P5 480 40 240 to 900 CR6L-50/UL FUJI 317
50A
600V
47P5 480 50 320 to 900 CR6L-75/UL FUJI 564
75A
600V
4011 480 50 1000 to 1800 CR6L-100/UL FUJI 1022
100A
600V
4015 480 60 1500 to 4100 CR6L-150/UL FUJI 3070
150A
600V
4018 480 70 530 to 5800 CR6L-150/UL FUJI 3070
150A
600V
4022 480 90 1130 to 5800 CR6L-150/UL FUJI 3070
400 V 150A
Class 600V
4030 480 110 1700 to 5800 CR6L-150/UL FUJI 3070
150A
600V
4037 480 140 2000 to 13000 CR6L-200/UL FUJI 5200
200A
600V
4045 480 160 3000 to 13000 CR6L-200/UL FUJI 5200
200A
600V
4055 480 220 6800 to 55000 CR6L-300/UL FUJI 17700
300A
600V
4075 480 280 9000 to 55000 CR6L-300/UL FUJI 17700
300A
700V
4090 480 330 12000 to 23000 A70P400-4 FERRAZ 19000
400A
700V
4110 480 400 18000 to 64000 A70P450-4 FERRAZ 24000
450A
700V
4132 480 450 28000 to 250000 A70P600-4 FERRAZ 43000
600A
700V
4160 480 540 40000 to 250000 A70P700-4 FERRAZ 59000
700A
700V
4185 480 620 43000 to 400000 A70P900-4 FERRAZ 97000
900A
700V
4220 480 750 63000 to 400000 A70P900-4 FERRAZ 97000
900A
700V
4300 480 1000 94000 to 920000 A70P1000-4 FERRAZ 120000
1000A

10-16
 Conformance to CE Markings

„EMC Directive
Varispeed G7-Series Inverters satisfy testing for conformance to the EMC Directive under the conditions
described in European Standard EN61800-3.

Installation Method
In order to ensure that the machinery or installation incorporating the Inverter conforms to the EMC Directive,
perform installation according to the method below.
• Install a noise filter that conforms to European Standards on the input side. (Refer to Table 10.5 EMC
Noise Filters).
• Use a shielded line or metal piping for wiring between the Inverter and Motor. Make the wiring as short as
possible.
• To suppress harmonics, install a DC reactor in CIMR-G7B20P4, 20P7, 40P4, and 40P7 models. (Refer to
Table 10.6 DC Reactors for Suppressing Harmonics.)

R/L1, S/L2, T/L3 PE

Remove the paint on the ground side.

Inputs
Inverter
Filter

Outputs U/T1, V/T2, W/T3

R/L1, S/L2, T/L3

Wiring length:
40 cm max.

Metallic plate
Wiring length: 20 m max.
Remove the paint on the ground side.

IM

Fig 10.7 Installation Method for Filter and Inverter (CIMR-G7B20P4 to 2015, 40P4 to 4015) 10

10-17
 R/L1, S/L2, T/L3 PE
Remove the paint on the ground side.

Inputs
Inverter
Filter

Outputs
U/T1, V/T2, W/T3
R/L1, S/L2, T/L3

Wiring length:
40 cm max.

Metallic plate
Wiring length: 20 m max.
Remove the paint on the ground side.

IM

Fig 10.8 Installation Method for Filter and Inverter (CIMR-G7B2018 to 2110, 4018 to 4300)

Table 10.5 EMC Noise Filters

Volt- Inverter Model Noise Filter (Made by Schaffner)
age Number
Class Model Number Rated Current (A) Weight (kg) Dimensions (mm)
CIMR-G7B
20P4 FS5972-10-07 10 1.1 141 × 46 × 330
20P7 FS5972-10-07 10 1.1 141 × 46 × 330
21P5 FS5972-18-07 18 1.3 141 × 46 × 330
22P2 FS5973-35-07 35 1.4 141 × 46 × 330
23P7 FS5973-35-07 35 1.4 141 × 46 × 330
25P5 FS5973-60-07 60 3 141 × 46 × 330
27P5 FS5973-60-07 60 3 206 × 60 × 355
2011 FS5973-100-07 100 4.9 236 × 80 × 408
200V 2015 FS5973-100-07 100 4.9 236 × 80 × 408
Class
2018 FS5973-130-35 130 4.3 90 × 180 × 366
2022 FS5973-130-35 130 4.3 90 × 180 × 366
2030 FS5973-160-40 160 6 120 × 170 × 451
2037 FS5973-240-37 240 11 130 × 240 × 610
2045 FS5973-240-37 240 11 130 × 240 × 610
2055 FS5972-400-99 400 18.5 300 × 160 × 610
2075 FS5972-400-99 400 18.5 300 × 160 × 610
2090
FS5972-460-99 460 19.5 300 × 160 × 610
2110

10-18
 Conformance to CE Markings

Table 10.5 EMC Noise Filters (Continued)

Volt- Inverter Model Noise Filter (Made by Schaffner)
age Number
Class Model Number Rated Current (A) Weight (kg) Dimensions (mm)
CIMR-G7B
40P4 FS5972-10-07 10 1.1 141 × 46 × 330
40P7 FS5972-10-07 10 1.1 141 × 46 × 330
41P5 FS5972-10-07 10 1.1 141 × 46 × 330
42P2 FS5972-18-07 18 1.3 141 × 46 × 330
43P7 FS5972-18-07 18 1.3 141 × 46 × 330
44P0 FS5972-18-07 18 1.3 141 × 46 × 330
45P5 FS5972-35-07 35 2.1 206 × 50 × 355
47P5 FS5972-35-07 35 2.1 206 × 50 × 355
4011 FS5972-60-07 60 4.0 236 × 65 × 408
4015 FS5972-60-07 60 4.0 236 × 65 × 408
4018 FS5972-70-52 70 3.4 80 × 185 × 329

400V 4022 FS5972-70-52 70 3.4 80 × 185 × 329

Class 4030 FS5972-130-35 130 4.7 90 × 180 × 366
4037 FS5972-130-35 130 4.7 90 × 180 × 366
4045 FS5972-130-35 130 4.7 90 × 180 × 366
4055 FS5972-170-40 170 6 120 × 170 × 451
4075 FS5972-170-40 170 6 120 × 170 × 451
4090 FS5972-250-37 250 11 130 × 240 × 610
4110 FS5972-250-37 250 11 130 × 240 × 610
4132 FS5972-410-99 410 10.5 260 × 115 × 386
4160 FS5972-410-99 410 10.5 260 × 115 × 386
4185 FS5972-600-99 600 18.5 260 × 135 × 386
4220 FS5972-800-99 800 31 300 × 160 × 716
4300 FS5972-800-99 800 31 300 × 160 × 716

Table 10.6 DC Reactors for Suppressing Harmonics

Inverter Model DC Reactor
Voltage Class Number
Model Number Manufacturer Ratings Code Number
CIMR-G7B
20P4
10
200 V Class UZDA-B YASKAWA 5.4 A 8 mH X010084
20P7

40P4
400 V Class UZDA-B YASKAWA 3.2 A 28 mH X010052
40P7

10-19
 Wiring Examples
This section provides wiring examples to connect a Braking Unit and other peripheral devices to the main
circuits, examples of wiring a transformer to Inverter I/O, and other aspects of Inverter wiring.

‹ Using a Braking Resistor Unit

This example shows wiring for a Braking Resistor Unit.
CIMR-G7B20P4 to -G7B2015 (200 V Class Inverters of 0.4 to 15 kW)
CIMR-G7B40P4 to -G7B4015 (400 V Class Inverters of 0.4 to 15 kW)

Braking Resistor overheating contacts

(Thermal overload relay trip contacts)
A sequence is required to turn DC Reactor to
OFF the power supply for the ther- improve input
mal overload relay trip contacts of power factor
the Braking Resistor Unit. (Optional) Braking Resistor Unit *3

Short-circuit bar

3-phase power MC *4 Motor

R/L1 U/T1
200 to 230 V 50/60 Hz
or 380 to 460 V S/L2 V/T2
50/60 Hz T/L3 W/T3
Inverter

200 V Class Inverters: Ground to

Overload relay trip contact
100 Ω max., 400 V Class Inverters:
of Braking Resistor Unit Ground to 10 Ω max.)

Fault contacts

* 1. A transformer is not required for 200 V Class

* 2. Remove the short-circuit bar (normally connected) from + 1 and + 2 when connecting a DC Reactor (Optional).
* 3. Disable stall prevention during deceleration by setting L3-04 and using a Braking Resistor Unit. The motor may not stop within the decel-
eration time if this setting is not changed.
* 4. When connecting a separately-installed type Braking Unit (model CDBR) to Inverters with built-in braking transistor (200 V/400 V 15 kW
or less), connect the B1 terminal of the Inverter to the + terminal of the Braking Unit and connect the - terminal of the Inverter to the - ter-
minal of the Braking Unit. The B2 terminal is not used in this case.
Fig 10.9

10-20
 Wiring Examples

‹ Using a Braking Unit and Braking Resistor Unit

When using a Braking Unit and Braking Resistor Unit, create a sequence to detect overheating of the braking
resistor and cut off the power supply to the Inverter.
CIMR-G7B2018, -G7B2022 (200 V Class Inverters of 18.5 kW, 22 kW)

DC Reactor to Braking Unit Braking Resistor Unit*2

improve input (Optional) (Optional)
A sequence is required to turn
power factor Level
OFF the power supply for the
(Optional) detector
thermal overload relay trip con-
tacts of the Braking Resistor
Unit. Braking Resistor overheating contacts
(Thermal overload relay trip contacts)
Short-circuit bar
MCCB
Motor
3-phase power R/L1 U/T1
200 to 230 V 50/60 Hz S/L2 V/T2
T/L3 W/T3
Inverter

Overload relay trip contact Ground to 100 Ω max.

of Braking Resistor Unit

Fault contacts
Forward Run/Stop
Forward Run Command (forward run when ON)
Reverse Run/Stop
Reverse Run Command (reverse run when ON)
Braking Unit
External fault

* 1. Remove the short-circuit bar (normally connected) from + 1 and + 2 when connecting a DC Reactor (Optional).
* 2. Disable stall prevention during deceleration by setting L3-04 when using a Braking Resistor Unit. The motor may not stop within the decel-
eration time if this setting is not changed.
Fig 10.10

10

10-21
 ‹ Using Braking Units in Parallel
This example shows wiring for using two Braking Units in parallel.
There are connectors for selecting whether each Braking Unit is to be a Master or Slave. Select “Master” for
the first Braking Unit only, and select “Slave” for all other Braking Units (i.e., from the second Unit onwards).

A sequence is required to turn OFF the

Thermal
power supply for the thermal overload relay Thermal protector
trip contacts of the Braking Resistor Unit. protector
Brak- Brak-
ing ing
Resis- Resis-
tor Unit tor Unit

detector
Level
Braking Unit 2

Thermal switch Thermal switch

MCCB
Motor
R/L1 U/T1
3-phase power Inverter
200 to 220 V 50 Hz S/L2 V/T2
200 to 230 V 60 Hz
T/L3 W/T3
Cooling fan

Overload relay trip contact Ground to 100 Ω max.

of Braking Resistor Unit

Fault contacts Fault contact output

Forward Run Com-
Forward Run/Stop mand (forward run
when ON)
Reverse Run/Stop
Reverse Run Com-
Braking Unit mand (reverse run
when ON)
External fault

* Disable stall prevention during deceleration by setting L3-04 to Resistor Unit. The motor may
not stop within the deceleration time if this setting is not changed.

Fig 10.11

10-22
 Wiring Examples

‹ Using a Braking Unit and Three Braking Resistor Units in Parallel

This example shows wiring for using three Braking Resistor Units in parallel.

Thermal Thermal Thermal

protector protector protector
Braking Braking Braking
Resistor Resistor Resistor
A sequence is required to turn OFF the Unit Unit Unit
power supply for the thermal overload relay
trip contacts of the Braking Resistor Unit.

detector
Level
Braking Unit

Thermal switch

MCCB
Motor
R/L1 U/T1
3-phase power Inverter
380 to 480 V S/L2 V/T2
50/60 Hz W/T3
T/L3
Cooling fan
Voltage
setting

Overload relay trip contact Ground to 10 Ω max.

of Braking Resistor Unit

Fault contact output

Fault contacts
Forward Run Com-
Forward Run/Stop mand (forward run
when ON)
Reverse Run/Stop
Reverse Run Com-
mand (reverse run
Braking Unit when ON)

External fault

* Disable stall prevention during deceleration by setting L3-04 to Resistor Unit. The motor may
not stop within the deceleration time if this setting is not changed.

Fig 10.12
10

10-23
 ‹ Using a VS Operator
This example shows wiring for using a VS Operator. The VS Operator model number is JVOP-95•† or
JVOP-96 •†.
CIMR-G7B27P5 (200 V Class Inverters of 7.5 kW)

Short-circuit bar
(Standard)

MCCB
Motor
R/L1 U/T1
3-phase power
S/L2 Inverter V/T2
T/L3 W/T3
JVOP-95•†, C-96•† VS Operator

Ground to 100 Ω max.

Forward Run Command
(forward run when closed)
Reverse Run Command
(reverse run when closed)

Multi-function contact inputs

Sequence common (0 V)

Shield terminal

Speed setting power (15 V, 20 mA)

Master speed (0 to 10 V, 20 kΩ)

Master speed (4 to 20 mA, 250 Ω)

Multi-function contact
output (Default: Running
signal)

Fault contact output

Open collector 1 (Default:
Zero-speed signal)

Multi-function Multi-function open-

analog output Open collector 2 (Default: collector output 48 V,
Frequency meter Speed agreement signal) 50 mA max.
Multi-function
analog output
(Default: Output Multi-function output
frequency) common

Fig 10.13

10-24
 Wiring Examples

‹ Using Transistors for Input Signals and a 0-V Common in Sinking Mode
with an Internal Power Supply
Set CN5 (shunt connector) on the control board to NPN as shown below for a sequence that uses an NPN tran-
sistor for an input signal (0-V command and sinking mode) and an internal +24-V power supply.

+1 +2 - B1 B2
MCCB

3-phase power
R R/L1 U/T1 Motor

S S/L2 V/T2 IM
T T/L3 Inverter W/T3

Ground
S1
Forward Run/Stop
S2
Reverse Run/Stop
S3
External fault
S4
Fault reset
Multi-function S5
contact inputs
Multi-step
Factory speed setting 1
settings

S12
Emergency stop CN5 (NPN setting) +24 V 8 mA
(NO contact)

SC

+24 V
E(G)
Shield wire
connection terminal

Pulse train input

RP Master speed pulse train
Frequency setting
adjustment 0 to 32 kHz (3 kΩ)
2 kΩ High level: 3.5 to 13.2 V input

Frequency Frequency setting power

setter +V
External
10
3 +15 V 20 mA
frequency 0 to +10 V
2 kΩ A1 Master speed reference
references 2
1 4 to 20 mA P 0 to 10 V (20 kΩ)
A2 Master speed reference
P AC 4 to 20 mA (250 Ω)
0 to 10 V (20 kΩ) input
0V

Fig 10.14

10-25
 ‹ Using Transistors for Input Signals and a +24-V Common in Sourcing
Mode
Set CN5 (shunt connector) on the control board to PNP as shown below for a sequence that uses a PNP tran-
sistor for an input signal (+24-V common and sourcing mode) and an internal +24-V power supply.

+1 +2 - B1 B2
MCCB

3-phase power
R R/L1 U/T1 Motor

S S/L2 V/T2 IM
T T/L3 Inverter W/T3

Ground
S1
Forward Run/Stop
S2
Reverse Run/Stop
S3
External fault
S4
Fault reset
Multi-function S5
contact inputs
Multi-step
Factory speed setting 1
settings

S12
Emergency stop CN5 (PNP setting) +24 V 8 mA
(NO contact)

SC

+24 V
E(G)
Shield wire
connection terminal

Pulse train input

RP Master speed pulse train
Frequency setting
adjustment 0 to 32 kHz (3 kΩ)
2 kΩ High level: 3.5 to 13.2 V input

Frequency +V Frequency setting power

External setter 3 +15 V 20 mA
frequency 0 to +10 V
2 kΩ A1 Master speed reference
references 2
0 to 10 V (20 kΩ)
1 4 to 20 mA P
A2 Master speed reference
P AC 4 to 20 mA (250Ω)
0 to 10 V (20 kΩ) input
0V

Fig 10.15

10-26
 Wiring Examples

‹ Using Transistors for Input Signals and a 0-V Common in Sinking Mode
with an External Power Supply
Set CN5 (shunt connector) on the control board to EXT as shown below for a sequence that uses an NPN tran-
sistor for an input signal (0-V common and sinking mode) and an external +24-V power supply.

+1 +2 - B1 B2
MCCB

3-phase power
R R/L1 U/T1 Motor

S S/L2 V/T2 IM
T T/L3 Inverter W/T3

Ground
S1
Forward Run/Stop
S2
Reverse Run/Stop
S3
External fault
S4
Fault reset
Multi-function S5
contact inputs
Multi-step
Factory
settings speed setting 1

S12
Emergency stop CN5 (EXT setting) +24 V 8 mA
(NO contact) External
+24V
SC

+24 V
E(G) Shield wire
connection terminal

Pulse train input

RP Master speed pulse train
Frequency setting
adjustment 0 to 32 kHz (3 kΩ)
2 kΩ High level: 3.5 to 13.2 V input

Frequency Frequency setting power

External setter
+V
3 +15 V 20 mA
frequency 0 to +10 V
2 kΩ A1 Master speed reference
references 2
0 to 10 V (20 kΩ)
1 4 to 20 mA P
A2 Master speed reference 10
P AC 4 to 20 mA (250 kΩ)
0 to 10 V (20 kΩ) input
0V

Note:
Set EXT as shown at the right even for
a PNP input signal transistor
sequence connection (+24-V S12
common/sourcing mode) with a +24-V
external power supply. +24 V 8 mA
CN5 (EXT setting)
External
+24V
SC

+24 V

Fig 10.16

10-27
 ‹ Using Contact and Open Collector Outputs
This example shows wiring for contact outputs and open collector outputs.
The following example is for the CIMR-G7B25P5 (200 V Class Inverter for 5.5 kW).

+1 +2 - B1 B2
MCCB
R R/L1 U/T1 Motor

3-phase power S S/L2 V/T2 IM

T T/L3 Inverter
W/T3

Ground

Ammeter scale adjustment resistor

AM 20 k
Multi-function analog output 2
-10 to +10 V 2 mA
AM Default: Ouput current,
0 to +10 V
Frequency meter scale adjustment resistor
FM 20 k
Multi-function analog output 1
AC FM -10 to +10 V 2 mA
Default: Output frequency,
0 to +10 V
E(G)
Sequence

Surge
absorber
MA

MB Error contact output

250 VAC max.
250 VAC, 10 mA min. 1 A max.
MC 30 VDC, 10 mA min. 1 A max.

Multi-function contact output

30 VDC max.
250 VAC, 10 mA min. 1 A max.
30 VDC, 10 mA min. 1 A max. Flywheel
(Default: RUN) diode
M1

M2
48 VDC max.
E(G) Flywheel
diode
P1
48 VDC max.
Open collector 1
Flywheel
(Default: zero speed)
diode
P2
Open collector 2
PC (Default: Freq agree)

Multi-function
open collector output
48 VDC 50 mA max.

Sequence external power

supply

Fig 10.17

10-28
 User Constants

User Constants
Factory settings are given in the following table.

Table 10.7 User Constants

Fac- Fac-
Set- Set-
No. Name tory No. Name tory
ting ting
Setting Setting
Language selection for Digital
A1-00
Operator display 7*1 b3-05 Speed search wait time 0.2

Speed search detection compensa-

A1-01 Constant access level 2 b3-10 1.10
tion gain (speed calculation)
Proportional gain of the speed esti-
A1-02 Control method selection 2*1 b3-13
mator during speed search
1.0

A1-03 Initialize 0 b3-14 Rotation direction search selection 1

A1-04 Password 0 b3-17 Speed search retrial current level 150

A1-05 Password setting 0 b3-18 Speed search retrial detection time 0.10

A2-01 to
User setting constants - b3-19 Number of speed search retrials 0
A2-32

b1-01 Reference selection 1 b4-01 Timer function ON-delay time 0.0

b1-02 Operation method selection 1 b4-02 Timer function OFF-delay time 0.0

b1-03 Stopping method selection 0 b5-01 PID control method selection 0

b1-04 Prohibition of reverse operation 0 b5-02 Proportional gain (P) 1.00

Operation selection for setting E1-

b1-05 0 b5-03 Integral (I) time 1.0
09 or less

b1-06 Read sequence input twice 1 b5-04 Integral (I) limit 100.0

Operation selection after switching

b1-07 0 b5-05 Derivative (D) time 0.00
to remote mode
Run Command selection in pro-
b1-08 0 b5-06 PID upper limit 100.0
gramming modes

b1-10 Mode selection for zero-speed 0 b5-07 PID offset adjustment 0.0

Zero-speed level (DC injection

b2-01 0.5 b5-08 PID first order lag time constant 0.00
braking starting frequency)
10
PID output characteristics selec-
b2-02 DC injection braking current 50 b5-09 0
tion

b2-03 DC injection braking time at start 0.00 b5-10 PID output gain 1.0

b2-04 DC injection braking time at stop 0.50 b5-11 PID reverse output selection 0

Magnetic flux compensation vol- Selection of PID feedback com-

b2-08 0 b5-12 0
ume mand loss detection
PID feedback command loss detec-
b3-01 Speed search selection 2*2 b5-13
tion level
0

PID feedback command loss detec-

b3-02 Speed search operating current 100*2 b5-14
tion time
1.0

b3-03 Speed search deceleration time 2.0 b5-15 PID sleep function operation level 0.0

10-29
 Table 10.7 User Constants (Continued)

Fac- Fac-
Set- Set-
No. Name tory No. Name tory
ting ting
Setting Setting

b5-16 PID sleep operation delay time 0.0 C1-10 Accel/decel time setting unit 1

Accel/decel time switching fre-

b5-17 Accel/decel time for PID reference 0.0 C1-11 0.0
quency
S-curve characteristic time at
b6-01 Dwell frequency at start 0.0 C2-01 0.20
acceleration start
S-curve characteristic time at
b6-02 Dwell time at start 0.0 C2-02 0.20
acceleration end
S-curve characteristic time at
b6-03 Dwell frequency at stop 0.0 C2-03 0.20
deceleration start
S-curve characteristic time at
b6-04 Dwell time at stop 0.0 C2-04 0.00
deceleration end

b7-01 Droop control gain 0.0 C3-01 Slip compensation gain 1.0*2

Slip compensation primary delay

b7-02 Droop control delay time 0.05 C3-02
time 200*2

b8-01 Energy-saving mode selection 0 C3-03 Slip compensation limit 200

Slip compensation selection during

b8-02 Energy-saving gain 0.7*3 C3-04
regeneration
0

Output voltage limit operation

b8-03 Energy-saving filter time constant 0.50*4 C3-05
selection
0

288.20
b8-04 Energy-saving coefficient C4-01 Torque compensation gain 1.00
*5 *6

Power detection filter time con- Torque compensation primary

b8-05
stant
20 C4-02
delay time constant 20*2

b8-06 Search operation voltage limiter 0 C4-03 Forward starting torque 0.0

b9-01 Zero-servo gain 5 C4-04 Reverse starting torque 0.0

b9-02 Zero-servo completion width 10 C4-05 Starting torque time constant 10

C1-01 Acceleration time 1 10.0 C5-01 ASR proportional (P) gain 1 20.00*7

C1-02 Deceleration time 1 10.0 C5-02 ASR integral (I) time 1 0.500*7

C1-03 Acceleration time 2 10.0 C5-03 ASR proportional (P) gain 2 20.00*7

C1-04 Deceleration time 2 10.0 C5-04 ASR integral (I) time 2 0.500*7

C1-05 Acceleration time 3 10.0 C5-05 ASR limit 5.0

C1-06 Deceleration time 3 10.0 C5-06 ASR primary delay time 0.004*7

C1-07 Acceleration time 4 10.0 C5-07 ASR switching frequency 0.0

C1-08 Deceleration time 4 10.0 C5-08 ASR integral (I) limit 400

C1-09 Emergency stop time 10.0 C5-10 ASR primary delay time 2 0.010

10-30
 User Constants

Table 10.7 User Constants (Continued)

Fac- Fac-
Set- Set-
No. Name tory No. Name tory
ting ting
Setting Setting

C6-02 Carrier frequency selection 6*6 d3-01 Jump frequency 1 0.0

C6-03*8 Carrier frequency upper limit 15.0*6 d3-02 Jump frequency 2 0.0

C6-04*8 Carrier frequency lower limit 15.0*6 d3-03 Jump frequency 3 0.0

Carrier frequency proportional

C6-05*8 gain 00 d3-04 Jump frequency width 1.0

Carrier frequency for open-loop Frequency reference hold function

C6-11
vector 2 control 1*6 d4-01
selection
0

d1-01 Frequency reference 1 0.00 d4-02 + - Speed limits 10

d1-02 Frequency reference 2 0.00 d5-01 Torque control selection 0

d1-03 Frequency reference 3 0.00 d5-02 Torque reference delay time 0*7

d1-04 Frequency reference 4 0.00 d5-03 Speed limit selection 1

d1-05 Frequency reference 5 0.00 d5-04 Speed limit 0

d1-06 Frequency reference 6 0.00 d5-05 Speed limit bias 10

Speed/torque control switching

d1-07 Frequency reference 7 0.00 d5-06 0
timer
Rotation direction limit operation
d1-08 Frequency reference 8 0.00 d5-07 1
selection

d1-09 Frequency reference 9 0.00 d6-01 Field weakening level 80

d1-10 Frequency reference 10 0.00 d6-02 Field frequency 0.0

d1-11 Frequency reference 11 0.00 d6-03 Field forcing function selection 0

d1-12 Frequency reference 12 0.00 d6-05 AφR time constant 1.00

d1-13 Frequency reference 13 0.00 d6-06 Field forcing limit 400

10
d1-14 Frequency reference 14 0.00 E1-01 Input voltage setting 200*9

d1-15 Frequency reference 15 0.00 E1-03 V/f pattern selection F

d1-16 Frequency reference 16 0.00 E1-04 Max. output frequency 50.0*2

200.0
d1-17 Jog frequency reference 6.00 E1-05 Max. voltage *2 *9

d2-01 Frequency reference upper limit 100.0 E1-06 Base frequency 50.0*2

d2-02 Frequency reference lower limit 0.0 E1-07 Mid. output frequency 3.0*2

d2-03 Master speed reference lower limit 0.0 E1-08 Mid. output frequency voltage 13.2*2 *9

10-31
 Table 10.7 User Constants (Continued)

Fac- Fac-
Set- Set-
No. Name tory No. Name tory
ting ting
Setting Setting

E1-09 Min. output frequency 0.5*2 E4-01 Motor 2 rated current 1.90 *6

E1-10 Min. output frequency voltage 2.4*2 *9 E4-02 Motor 2 rated slip 2.90 *6

E1-11 Mid. output frequency 2 0.0*10 E4-03 Motor 2 no-load current 1.20 *6

Motor 2 number of poles (number

E1-12 Mid. output frequency voltage 2 0.0*10 E4-04
of poles)
4

E1-13 Base voltage 0.0*11 E4-05 Motor 2 line-to-line resistance 9.842*6

E2-01 Motor rated current 1.90*6 E4-06 Motor 2 leak inductance 18.2*6

E2-02 Motor rated slip 2.90*6 E4-07 Motor 2 rated capacity 0.40*12

E2-03 Motor no-load current 1.20*6 F1-01 PG constant 600

Operation selection at PG open cir-

E2-04 Number of motor poles 4 F1-02 1
cuit (PGO)
Operation selection at overspeed
E2-05 Motor line-to-line resistance 9.842*6 F1-03
(OS)
1

E2-06 Motor leak inductance 18.2*6 F1-04 Operation selection at deviation 3

E2-07 Motor iron saturation coefficient 1 0.50 F1-05 PG rotation 0

PG division rate (PG pulse moni-

E2-08 Motor iron saturation coefficient 2 0.75 F1-06 1
tor)
Integral value during accel/decel
E2-09 Motor mechanical loss 0.0 F1-07 0
enable/disable
Motor iron loss for torque compen-
E2-10
sation 14*6 F1-08 Overspeed detection level 115

E2-11 Motor rated output 0.40*12 F1-09 Overspeed detection delay time 0.0*7

Excessive speed deviation detec-

E2-12 Motor iron saturation coefficient 3 1.30 F1-10 10
tion level
Excessive speed deviation detec-
E3-01 Motor 2 control method selection 2 F1-11 0.5
tion delay time
Motor 2 max. output frequency
E3-02 50.0 F1-12 Number of PG gear teeth 1 0
(FMAX)

E3-03 Motor 2 max. voltage (VMAX) 200.0*2 F1-13 Number of PG gear teeth 2 0

Motor 2 max. voltage frequency

E3-04 50.0 F1-14 PG open-circuit detection time 2.0
(FA)
Motor 2 mid. output frequency 1 Bi-polar or uni-polar input selec-
E3-05
(FB) 3.0 *2 F2-01
tion
0

Motor 2 mid. output frequency

E3-06
voltage 1 (VC) 13.2 *9 F3-01 Digital input option 0

Motor 2 min. output frequency

E3-07
(FMIN) 0.5 *2 F4-01 Channel 1 monitor selection 2

Motor 2 min. output frequency

E3-08
voltage (VMIN) 2.4 *9 F4-02 Channel 1 gain 1.00

10-32
 User Constants

Table 10.7 User Constants (Continued)

Fac- Fac-
Set- Set-
No. Name tory No. Name tory
ting ting
Setting Setting

F4-03 Channel 2 monitor selection 3 H1-03 Terminal S5 function selection 3 (0)*14

F4-04 Channel 2 gain 0.50 H1-04 Terminal S6 function selection 4 (3)*14

F4-05 Channel 1 output monitor bias 0.0 H1-05 Terminal S7 function selection 6 (4)*14

F4-06 Channel 2 output monitor bias 0.0 H1-06 Terminal S8 function selection 8 (6)*14

Analog output signal level for

F4-07 0 H1-07 Terminal S9 function selection 5
channel 1
Analog output signal level for
F4-08 0 H1-08 Terminal S10 function selection 32
channel 2

F5-01 Channel 1 output selection 0 H1-09 Terminal S11 function selection 7

F5-02 Channel 2 output selection 1 H1-10 Terminal S12 function selection 15

Terminal M1-M2 function selec-

F5-03 Channel 3 output selection 2 H2-01 0
tion (contact)
Terminal P1 function selection
F5-04 Channel 4 output selection 4 H2-02 1
(open collector)
Terminal P2 function selection
F5-05 Channel 5 output selection 6 H2-03 2
(open collector)
Terminal P3 function selection
F5-06 Channel 6 output selection 37 H2-04 6
(open-collector)
Terminal P4 function selection
F5-07 Channel 7 output selection 0F H2-05 10
(open-collector)
Signal level selection (terminal
F5-08 Channel 8 output selection 0F H3-01 0
A1)

F5-09 DO-08 output mode selection 0 H3-02 Gain (terminal A1) 100.0

Operation selection after commu-

F6-01 1 H3-03 Bias (terminal A1) 0.0
nications error
Input level of external fault from Signal level selection (terminal
F6-02 0 H3-04 0
Communications Option Board A3)
Multi-function analog input (termi-
Stopping method for external fault H3-05 2
nal A3) function selection 10
F6-03 from Communications Option 1
Board H3-06 Gain (terminal A3) 100.0

Trace sampling from Communica-

F6-04 0 H3-07 Bias (terminal A3) 0.0
tions Option Board
Torque reference/torque limit Signal level selection (terminal
F6-06 0 H3-08 2
selection from optical option A2)
Operation selection after SI-T Multi-function analog input (termi-
F6-08 1 H3-09 0
WDT error nal A2) function selection
Number of SI-T BUS error detec-
F6-09 2 H3-10 Gain (terminal A2) 100.0
tion

H1-01 Terminal S3 function selection 24 H3-11 Bias (terminal A2) 0.0

H1-02 Terminal S4 function selection 14 H3-12 Analog input filter time constant 0.03

10-33
 Table 10.7 User Constants (Continued)

Fac- Fac-
Set- Set-
No. Name tory No. Name tory
ting ting
Setting Setting
Alarm operation selection during
H4-01 Monitor selection (terminal FM) 2 L1-03 3
motor overheating
Motor overheating operation selec-
H4-02 Gain (terminal FM) 1.00 L1-04 1
tion
Motor temperature input filter time
H4-03 Bias (terminal FM) 0.0 L1-05 0.20
constant

H4-04 Monitor selection (terminal AM) 3 L2-01 Momentary power loss detection 0

Momentary power loss ridethru

H4-05 Gain (terminal AM) 0.50 L2-02
time 0.1*6

H4-06 Bias (terminal AM) 0.0 L2-03 Min. baseblock time 0.2*6

Analog output 1 signal level selec-

H4-07
tion
0 L2-04 Voltage recovery time 0.3*6

Analog output 2 signal level selec-

H4-08
tion
0 L2-05 Undervoltage detection level 190*9

H5-01 Slave address 1F L2-06 KEB deceleration time 0.0

H5-02 Communication speed selection 3 L2-07 Momentary recovery time 0.0*15

Frequency reduction gain at KEB

H5-03 Communication parity selection 0 L2-08 100
start
Stopping method after communi- Stall prevention selection during
H5-04 3 L3-01 1
cation error accel
Communication error detection
H5-05 1 L3-02 Stall prevention level during accel 150
selection

H5-06 Send wait time 5 L3-03 Stall prevention limit during accel 50

Stall prevention selection during

H5-07 RTS control ON/OFF 1 L3-04 1
decel
Unit Selection for MEMOBUS Stall prevention selection during
H5-10 0 L3-05 1
Register 0025H running
Stall prevention level during run-
H6-01 Pulse train input function selection 0 L3-06 160
ning

H6-02 Pulse train input scaling 1440 L3-11 Overvoltage inhibit selection 0

H6-03 Pulse train input gain 100.0 L3-12 Overvoltage inhibit voltage level 380*9

H6-04 Pulse train input bias 0.0 L4-01 Speed agreement detection level 0.0

H6-05 Pulse train input filter time 0.10 L4-02 Speed agreement detection width 2.0

Speed agreement detection level

H6-06 Pulse train monitor selection 2 L4-03 0.0
(+/-)
Speed agreement detection width
H6-07 Pulse train monitor scaling 1440 L4-04 2.0
(+/-)
Operation when frequency refer-
L1-01 Motor protection selection 1 L4-05 0
ence is missing

L1-02 Motor protection time constant 1.0 L5-01 Number of auto restart attempts 0

10-34
 User Constants

Table 10.7 User Constants (Continued)

Fac- Fac-
Set- Set-
No. Name tory No. Name tory
ting ting
Setting Setting
OH1 detection of Inverter’s cool-
L5-02 Auto restart operation selection 0 L8-32 1
ing fan
Carrier frequency reduction selec-
L6-01 Torque detection selection 1 0 L8-38 tion 1*19

2.0
L6-02 Torque detection level 1 150 L8-39 Reduced carrier frequency
*6 *13

L6-03 Torque detection time 1 0.1 L8-41 Current alarm 1

Hunting-prevention function selec-

L6-04 Torque detection selection 2 0 N1-01 1
tion

L6-05 Torque detection level 2 150 N1-02 Hunting-prevention gain 1.00

L6-06 Torque detection time 2 0.1 N1-03 Hunting-prevention time constant 10*6

Speed feedback detection control

L7-01 Forward drive torque limit 200 N2-01 1.00
(AFR) gain
Speed feedback detection control
L7-02 Reverse drive torque limit 200 N2-02 50
(AFR) time constant
Speed feedback detection control
L7-03 Forward regenerative torque limit 200 N2-03 750
(AFR) time constant 2
High-slip braking deceleration fre-
L7-04 Reverse regenerative torque limit 200 N3-01 5
quency width
Integral time setting for torque
L7-06 200 N3-02 High-slip braking current limit 150
limit

Control method selection for N3-03 High-slip braking stop dwell time 1.0
L7-07 torque limit during acceleration 0
deceleration N3-04 High-slip braking OL time 40

Protect selection for internal DB

L8-01 0
resistor (Type ERF)
N4-07 Integral time of speed estimator 0.030
L8-02 Overheat pre-alarm level 95*6

Operation selection after overheat Proportional gain of speed estima-

L8-03 3 N4-08 15
pre-alarm tor
Input open-phase protection selec- High-speed proportional gain of
L8-05 0 N4-10 15.0
tion speed estimator 10
Output open-phase protection Speed estimator switching fre-
L8-07 0 N4-11 70
selection quency
Low-speed regeneration stability
L8-09 Ground protection selection 1 N4-15 0.3
coefficient 1

L8-10 Cooling fan control selection 0 N4-17 Torque adjustment gain 0.8

L8-11 Cooling fan control delay time 60 N4-18 Feeder resistance adjustment gain 1.00

Speed estimator switching fre-

L8-12 Ambient temperature 45 N4-28 50
quency 2
OL2 characteristics selection at
L8-15 1 N4-29 Torque adjustment gain 2 0.10
low speeds
Low-speed regeneration stability
L8-18 Soft CLA selection 1 N4-30 1.00
coefficient 2

10-35
 Table 10.7 User Constants (Continued)

Fac- Fac-
Set- Set-
No. Name tory No. Name tory
ting ting
Setting Setting
Speed estimator gain fluctuation Cumulative operation time selec-
N4-32 5.0 o2-08 0
frequency 1 tion
Speed estimator gain fluctuation
N4-33 20.0 o2-10 Fan operation time setting 0
frequency 2
Speed estimator gain fluctuation Fault trace/fault history clear func-
N4-34 200.0 o2-12 0
rate tion
Output power monitor clear selec-
N5-01 Feed forward control selection 0*7 o2-14
tion
0

N5-02 Motor acceleration time 0.178*6 o2-18 Capacitor maintenance setting 0

N5-03 Feed forward proportional gain 1.0 o3-01 Copy function selection 0

o1-01 Monitor selection 6 o3-02 Read permitted selection 0

o1-02 Monitor selection after power up 1 T1-00 Motor 1/2 selection 1

Frequency units of reference set-

o1-03
ting and monitor
0 T1-01 Autotuning mode selection 0*2

Setting unit for frequency con-

o1-04
stants related to V/f characteristics
0 T1-02 Motor output power 0.40*6

o1-05 LCD brightness adjustment 3 T1-03 Motor rated voltage 200.0*9

LOCAL/REMOTE key enable/dis-

o2-01
able
1 T1-04 Motor rated current 1.90*6

STOP key during control circuit

o2-02 1 T1-05 Motor base frequency 50.0
terminal operation

o2-03 User constant initial value 0 T1-06 Number of motor poles 4

o2-04 kVA selection 0*6 T1-07 Motor base speed 1450

Frequency reference setting PG pulses per revolution for teach-

o2-05 0 T1-08 600
method selection ing
Operation selection when digital
o2-06
operator is disconnected
0 T1-09 Motor no-load current 1.20*6

o2-07 Cumulative operation time setting 0

* 1. Not initialized. (Japanese standard specifications: A1-00 = 1, A1-02 = 2)

* 2. When the control method is changed, the factory setting will change. The open-loop vector 1 factory settings are given.
* 3. The factory setting is 1.0 when using flux vector control.
* 4. The factory setting is 2.00 s when Inverter capacity is 55 kW min.
The factory setting will change when the control method is changed. The open-loop vector 1 factory setting is given.
* 5. By setting E2-11 (Motor rated output) the appropriate value will be set.
* 6. The factory settings depend on the Inverter capacity. The values for a 200 V Class Inverter of 0.4 kW are given.
* 7. When the control method is changed, the factory settings will change. The flux vector factory settings are given.
* 8. This constant can be monitored or set only when F is set for C6-02.
* 9. These are values for a 200 V Class Inverter. Values for a 400 V Class Inverter are double.
* 10.E1-11 and E1-12 are disregarded when set to 0.0.
* 11.E1-13 is set to the same value as E1-05 by autotuning.
* 12.The same capacity as that of the Inverter will be set if the constants are initialized.
* 13.If a current exceeding 110% of the Inverter rated current flows through the unit, the carrier frequency will automatically decrease and electromagnetic noise will
occur.
* 14.The factory settings in the parentheses are for 3-wire sequence.
* 15.If the setting is 0, the axis will accelerate to the specified speed for the specified acceleration time (C1-01 to C1-08).

10-36
 Index

INDEX EF0 Opt External Flt - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-9

emergency stop- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-17
enclosed wall-mounted type - - - - - - - - - - - - - - - - - - - - - - - 1-4
energy-saving - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6-115
excessive speed deviation - - - - - - - - - - - - - - - - - - - - 7-8, 7-16
Symbols external fault function- - - - - - - - - - - - - - - - - - - - - - - - - - 6-85
+/- speed - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-82 F
Numerics FJOG - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-84
2-wire sequence - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-10 forward/reverse run commands input together - - - - - - - - - - - 7-15
frequency reference - - - - - - - - - - - - - - - - - - - - - - - - 6-2, 6-28
3-wire sequence - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-11
fuse blown - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-3
A
G
AC reactor - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-17
ground fault - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-2
acceleration and deceleration times - - - - - - - - - - - - - - - - - - 6-18
ground fault interrupter - - - - - - - - - - - - - - - - - - - - - - - - - 2-16
advanced programming mode - - - - - - - - - - - - - - - - - - 3-5, 3-10
ASIC internal RAM fault - - - - - - - - - - - - - - - - - - - - - - - - 7-11 ground wiring - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-20
ASIC version fault - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-11 H
auto restart - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-72
high-slip braking OL - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-7
autotuning - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-9
hunting-prevention function - - - - - - - - - - - - - - - - - - - - - - 6-40
autotuning mode - - - - - - - - - - - - - - - - - - - - - - - - - - 3-5, 3-14
I
B
incorrect inverter capacity setting - - - - - - - - - - - - - - - - - - - 7-19
baseblock circuit error - - - - - - - - - - - - - - - - - - - - - - - - - 7-10
inductive noise - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-19
braking resistor - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-21
inrush prevention circuit fault - - - - - - - - - - - - - - - - - - - - - - 7-4
braking resistor unit - - - - - - - - - - - - - - - - - - - - - - 2-21, 10-20
installation site - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-9
braking unit - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -10-21
installed braking resistor overheating - - - - - - - - - - - - - - - - - 7-5
C internal braking transistor fault - - - - - - - - - - - - - - - - - - - - - 7-5
circuit breaker - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-16 inverter input voltage - - - - - - - - - - - - - - - - - - - - - - - - - -6-121
inverter overload - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-7
common specifications - - - - - - - - - - - - - - - - - - - - - - - - - - 9-4
communications on standby - - - - - - - - - - - - - - - - - - - - - - 7-17 J
communications option board A/D converter error - - - - - - - - 7-11
jump frequency function - - - - - - - - - - - - - - - - - - - - - - - - 6-31
communications option card DPRAM error - - - - - - - - - - - - - 7-11
communications option card model code error - - - - - - - - - - - 7-11 L
communications option card self diagnostic error - - - - - - - - - 7-11 limiting motor rotation direction - - - - - - - - - - - - - - - - - - - 6-62
constant selection error - - - - - - - - - - - - - - - - - - - - - - - - - 7-19 loaded operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-16
constant setting error - - - - - - - - - - - - - - - - - - - - - - - - - - 7-20
constant setting range error - - - - - - - - - - - - - - - - - - - - - - 7-19 M
control circuit terminals - - - - - - - - - - - - - - - - - - - - - - - - 2-22 magnetic contactor - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-17
control fault - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-8 main circuit overvoltage - - - - - - - - - - - - - - - - - - - - - - - - - 7-3
control method - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-8 main circuit undervoltage - - - - - - - - - - - - - - - - - - - - 7-3, 7-15
control method selection error - - - - - - - - - - - - - - - - - - - - - 7-19 main circuit voltage fault - - - - - - - - - - - - - - - - - - - - - - - - - 7-4
control power fault - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-4 maintenance and inspection - - - - - - - - - - - - - - - - - - - - - - - 8-1
cooling fin overheating - - - - - - - - - - - - - - - - - - - - - - - - - - 7-4 MEMOBUS communications - - - - - - - - - - - - - - - - - - - - - 6-92
CPU internal A/D converter error - - - - - - - - - - - - - - - 7-10, 7-11 MEMOBUS communications error - - - - - - - - - - - - - - - 7-9, 7-17
CPU-ASIC mutual diagnosis fault - - - - - - - - - - - - - - - - - - 7-11 modes - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-5
crimp terminals- - - - - - - - - - - - - - - - - - - - - - - 2-6, 2-22, 2-38 motor constants - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6-117
motor overheating - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-16
D motor overheating alarm - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
daily inspection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-2 motor overheating fault - - - - - - - - - - - - - - - - - - - - - - - - - - 7-5
DC reactor - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-17 motor overload - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-6
detecting motor overspeed - - - - - - - - - - - - - - - - - - - - - - -6-161 motor protection operation time - - - - - - - - - - - - - - - - - - - - 6-59
detecting motor torque - - - - - - - - - - - - - - - - - - - - - - - - - 6-53 mounting dimensions - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-6
detecting PG open circuit - - - - - - - - - - - - - - - - - - - - - - - -6-161 multi-function analog input - - - - - - - - - - - - - - - - - - - - - - 6-47
digital operator - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-2 multi-function analog input selection error - - - - - - - - - - - - - 7-19
digital operator communications error 1 - - - - - - - - - - - - - - - 7-10 multi-function input selection error - - - - - - - - - - - - - - - - - - 7-19
digital operator communications error 2 - - - - - - - - - - - - - - - 7-10 multi-speed operation - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-5
digital operator connection fault- - - - - - - - - - - - - - - - - - - - - 7-9
digital output cards - - - - - - - - - - - - - - - - - - - - - - - - - - -6-162 N
drive mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-5, 3-7 noise filter- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-17
dwell function - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-22 no-load operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-16
number of gear teeth between PG and motor - - - - - - - - - - - -6-161
E number of PG pulses - - - - - - - - - - - - - - - - - - - - - - - - - -6-160
EEPROM error - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-10
EEPROM write error - - - - - - - - - - - - - - - - - - - - - - - - - - 7-20

Index-1
Index

O undertorque 2 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-16
undertorque detected 1 - - - - - - - - - - - - - - - - - - - - - - - - - - -7-8
open chassis type - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-4
undertorque detected 2 - - - - - - - - - - - - - - - - - - - - - - - - - - -7-8
open-loop vector control - - - - - - - - - - - - - - - - - - - - - - - - - 4-9
user constant access levels - - - - - - - - - - - - - - - - - - - - - - - - 4-17
operation errors - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7-19
option card communications error - - - - - - - - - - - - - - - - - - -7-17 V
option card connection error - - - - - - - - - - - - - - - - - - - - - - -7-11
V/f control - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-8
option card selection error - - - - - - - - - - - - - - - - - - - - - - - -7-19
V/f control with PG - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-8
option communications error - - - - - - - - - - - - - - - - - - - - - - 7-9 V/f pattern - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-120, 6-122
output open-phase - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-4
verify mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-5, 3-13
overcurrent - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-2
VS operator - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10-24
overspeed - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-8, 7-16
overtorque 2 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7-16 W
overtorque detected 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-7 watchdog timer fault - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-11
overtorque detected 2 - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-7 wire size - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-22
wiring - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2-1
P
password - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-17, 6-156
periodic inspection - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-2
periodic maintenance of parts - - - - - - - - - - - - - - - - - - - - - - 8-3
PG (encoder) pulses - - - - - - - - - - - - - - - - - - - - - - - - - - - -2-39
PG disconnection - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7-16
PG disconnection detected - - - - - - - - - - - - - - - - - - - - - - - - 7-8
PG pulse monitor output dividing ratio - - - - - - - - - - - - - - - 6-161
PG rotation direction - - - - - - - - - - - - - - - - - - - - - - - - - - 6-160
PG speed control card - - - - - - - - - - - - - - - - - - - - - - - - - 6-160
PG speed control cards - - - - - - - - - - - - - - - - - - - - - - - - - -2-31
PID control - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-106
PID control selection error - - - - - - - - - - - - - - - - - - - - - - - -7-19
PID feedback reference lost - - - - - - - - - - - - - - - - - - - 7-8, 7-17
power ON- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-3

Q
quick programming mode - - - - - - - - - - - - - - - - - - - - - 3-5, 3-8

R
radio interference - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2-20
rated current - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6-58
RJOG - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6-84
run command - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6-10

S
S-curve characteristics - - - - - - - - - - - - - - - - - - - - - - - - - -6-21
setting speed limit bias - - - - - - - - - - - - - - - - - - - - - - - - - 6-132
slip compensation function - - - - - - - - - - - - - - - - - - - - - - -6-36
speed control with PG - - - - - - - - - - - - - - - - - - - - - - - - - 6-158
stabilizing speed - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6-41
stall prevention function - - - - - - - - - - - - - - - - 6-23, 6-25, 6-50
standard connection diagrams - - - - - - - - - - - - - - - - - - - - - -2-15
standard inverter specifications - - - - - - - - - - - - - - - - - - - - - 9-2
stopping methods - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6-12
straight solderless terminals - - - - - - - - - - - - - - - - - - -2-23, 2-38
surge absorber - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2-17
switching motors when the power supply is ON - - - - - - - - - - 6-149

T
terminal block - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-5
thermal overload relay - - - - - - - - - - - - - - - - - - - - - - - - - -2-19
tightening torque - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2-38
timer function - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-105
torque compensation - - - - - - - - - - - - - - - - - - - - - - - - - - -6-38
torque limit function - - - - - - - - - - - - - - - - - - - - - - - - - - -6-46
trial operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-1
troubleshooting - - - - - - - - - - - - - - - - - - - - - - - - - - 7-1, 7-24

U
undertorque 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7-16

Index-2
Revision History

The revision dates and numbers of the revised manuals are given on the bottom of the back cover.

MANUAL NO.‫ޓ‬TOEP C710616 13B

Published in Japan August 200807-12 1
Revision number
Date of Date of original
publication publication

Date of Rev.
Publication No. Section Revised Content

December 2007 − First edition

August 2008 1 Chapter 4, 5, 6, 10 Revision: A1-00, C6-11, F4-01, F4-03, H4-01, H4-04, L2-07, L8-41, T1-05, T1-07
Chapter 5 Addition: Factory Settings that Change with the Control Method (A1-02)
C6-02
Chapter 10 Revision: Low Voltage Directive and EMC Directive
Back cover Revision: Address
Varispeed G7
INSTRUCTION MANUAL
IRUMA BUSINESS CENTER (SOLUTION CENTER)
480, Kamifujisawa, Iruma, Saitama 358-8555, Japan
Phone 81-4-2962-5696 Fax 81-4-2962-6138
YASKAWA ELECTRIC AMERICA, INC.
2121 Norman Drive South, Waukegan, IL 60085, U.S.A.
Phone 1-847-887-7000 Fax 1-847-887-7370
YASKAWA ELETRICO DO BRASIL LTDA.
Avenida Fagundes Filho, 620 Sao Paulo-SP CEP 04304-000, Brazil
Phone 55-11-3585-1100 Fax 55-11-5581-8795
YASKAWA ELECTRIC EUROPE GmbH
Hauptstraβe 185, 65760 Eschborn, Germany
Phone 49-6196-569-300 Fax 49-6196-569-398
YASKAWA ELECTRIC UK LTD.
1 Hunt Hill Orchardton Woods Cumbernauld, G68 9LF, United Kingdom
Phone 44-1236-735000 Fax 44-1236-458182
YASKAWA ELECTRIC KOREA CORPORATION
7F, Doore Bldg. 24, Yeoido-dong, Youngdungpo-Ku, Seoul 150-877, Korea
Phone 82-2-784-7844 Fax 82-2-784-8495
YASKAWA ELECTRIC (SINGAPORE) PTE. LTD.
151 Lorong Chuan, #04-01, New Tech Park 556741, Singapore
Phone 65-6282-3003 Fax 65-6289-3003
YASKAWA ELECTRIC (SHANGHAI) CO., LTD.
No.18 Xizang Zhong Road. Room 1702-1707, Harbour Ring Plaza Shanghai 200001, China
Phone 86-21-5385-2200 Fax 86-21-5385-3299
YASKAWA ELECTRIC (SHANGHAI) CO., LTD. BEIJING OFFICE
Room 1011A, Tower W3 Oriental Plaza, No.1 East Chang An Ave.,
Dong Cheng District, Beijing 100738, China
Phone 86-10-8518-4086 Fax 86-10-8518-4082
YASKAWA ELECTRIC TAIWAN CORPORATION
9F, 16, Nanking E. Rd., Sec. 3, Taipei, Taiwan
Phone 886-2-2502-5003 Fax 886-2-2505-1280

YASKAWA ELECTRIC CORPORATION

YASKAWA

In the event that the end user of this product is to be the military and said product is to be
employed in any weapons systems or the manufacture thereof, the export will fall under
the relevant regulations as stipulated in the Foreign Exchange and Foreign Trade
Regulations. Therefore, be sure to follow all procedures and submit all relevant
documentation according to any and all rules, regulations and laws that may apply. MANUAL NO. TOEP C710616 13B
Specifications are subject to change without notice
for ongoing product modifications and improvements. Published in Japan August 2008 07-12 1
08-5-10
© 2007-2008 YASKAWA ELECTRIC CORPORATION. All rights reserved.