PHYSICS INVESTIGATORY PROJECT

SUBMITTED BY:- Kaustubh Tripathi

TH
A (Science)
CLASS:- XII
SUBMITTED TO:- Mr. Anil Kumar Bharat Sir
 CERTIFICATE
This is to certify that Pratibha Singh, a
student of class XII-A has successfully
completed the research on the below
mentioned project under the guidance of
Mr. Amit Parashar (subject teacher)
during the year 2018 – 2019 in partial
fulfillment of physics practical examination.
 ACKNOWLEDGEMENT
Primarily I would thank god for being able to complete
this success. Then I would like to thank my physics
teacher Mr. Amit Parashar, whose valuable guidance
has been the ones that helped me patch this project and
make it full proof success his suggestions and his
instructions has served as the major contributor towards
the completion of the project.
Then I would like to thank my parents and friends who
have helped me with their valuable suggestions and
guidance has been helpful in various phases of the
completion of the project.
Last but not least I would like to thank my classmates
who have helped me a lot.
 ACKNOWLEDGEMENT

1. Certificate of Excellence
2. Aim Of Project
3. Introduction
4. Theory
5. Apparatus Required
6. Procedure Follwed
7. Observation
8. Conclusion
9. Precaution
 I‌
NTRODUCTION
The transformer is a device used for
converting a low alternating voltage
to a high alternating voltage or vice
versa. A Transformer based on the
principle of mutual induction
according to this principle , the
amount of magnetic flux linked with
a coil changing, an E.M.F is induced
in the neighboring coil.
A transformer is an electrical device
which is used
As such transformer are built in an
amazing strength of sizes. In electronic,
measurement and control circuits,
transformer size may be so small that it
weight only a few tones of gram where
as in high voltage power circuits, it may
weight hundred of tones.
In a transformer, the electrical energy transfer from one
circuit to another circuit takes place without the use of
moving parts.

A transformer which increases the voltage is called a

step-up transformer.
A transformer which decreases the A.C. voltages is
step-down transformer.
Tranformer is therefore, an essential piece of apparatus
both for high and low current circuits.
OBJECTIVE

To investigate the relation between

the ratio of:-
1. Input and output voltage.
2. Number of turnings in the secondary
coil and primary coil of a self made
transformer.
 THEORY‌
When an alternating e.m.f. is supplied to the
primary coil P1 P2 , an alternating current
starts falling in it.
The alternating current in the primary
produces a
changing magnetic flux, which induces
alternating voltage in the primary as well as
in the secondary. In a good-transformer,
whole of the magnetic flux linked with
primary is also linked with the secondary is
equal to that induced in each turn of the
primary.
 Thus if Ep and Es be the instantaneous values f the e.m.f’s
induced in the primary secondary coils of the transformer
and
dϕ/dt= rate of change of flux in each turnoff the
coil at this instant, we have
Ep= -Np dϕ/dt………………. (1)
And
Es = -Nsdϕ/dt………………….(2)
Since the above relations are true at every instant, so
by diving 2 by 1 , we get
E/Es =p -N/N……………….(3)
s p

As pEis the instantaneous value of back e.m.f induced

inthe primary coil P 1 ,so the instantaneous current in
primary coil is due to the difference
(E
p – E) in the instantaneous value of the applied
and back
e.m.f. further if R p is the resistance o, P 1P 2 coil
is given by
Ip = E-Ep /Rp
E-Ep= IpRp
Thus back e.m.f = input e.m.f
Hence equation 3 can be written as
Es/Ep = Es/E
= output e.m.f = input e.m.f
= Ns/Np = K
Where K is constant turn or transformation ratio.
In a Step Down
Transformer
Es˂E so K ˂ 1, HenceS N ˂N P

If
Ip = value of secondary primary current at same
instant
And
Is = value of secondary current at this instant , then
Input power at the instant = EpIp
And
Output power at the same instant = EsIs
If there are no losses of power in the transformer, then
input power = output power
Or
Ep Ip=Es Is

Or
E s/Ep=Ip/Is=K
Illustration
In a Step Up Transformer

Es˃E so K˃1 , hence Ns˃N p As , K ˃1 , so Ip˃Is is or

Is > Ip
i.e. current in secondary is weaker when secondary voltage is
higher.
Hence, what ever we gain in voltage, we lose in current in
the same ratio.
Similarly it can be shown, that in a step down transformer,
whatever we lose in voltage, we gain in current in the same
ratio.
Thus a step up transformer in reality steps down the current
& a step down transformer steps up the current
Illustration
 Efficiency
Efficiency of a transformer is defined as the ratio of output power to
the input power.
i.e. η=output power/input power= Es Is/Ep Ip
Thus in an ideal transformer, where there is no power losses, η=1.
But in actual practice, there are many power losses; therefore the
efficiency of transformer is less than one.
Efficiency = 1 - = 1 - I21R1+W1/V1I1cosϕ1

η = 1- I1R /V
1 cosϕ
1 – W/ V1I1cosϕ1
differentiating above equation with respect to I1
= 0 – R/1 Vcosϕ+
1 1W/ V1I 1 cosϕ1
2

η will be maximum at =0

Hence efficiency η will be maximum at

R1/ V1cosϕ1 =+ W/ V1I
1 cosϕ1
2

I21R1=W1
 Energy Losses
1. Copper Loss is the energy loss in the form of heat in
the copper coils of a transformer. This is due to joule
heating of conducting wires.
2. Iron Losses is the energy loss in the form of heat in the
iron core of the transformer.This is due to formation of
eddy currents in iron core.It is minimized by taking
laminated cores.
3. Leakage of magnetic flux occurs inspite of best
insulations.There,rate of change of magnetic flux
linked with each turn of S1 S2 is less than the rate of
change of magnetic flux linked with each turn of
P1 P2 .
4. Hysteresis Loss is the loss of energy due to repeated
magnetization and demagnetization of the iron core
when A.C. is fed to it.
5. Magneto striation i.e. humming noise of a
transformer
Apparatus Required
 Circuit Diagram
The mutual inductance term in the primary circuit
represents the load of the secondary. It has the
negative sign because it helps the source to produce
more current in response to increasing load in the
secondary circuit.

Vp = IpR1 + L1∆Ip / ∆t – M(∆Is/t)

M(∆Ip/t) = Is R2 + L2∆Is/∆t
The mutual inductance term in the secondary
represents the couping from the primary and acts as
the primary and acts as the voltage source that drives
source that drives the secondary circuit.
 Procedure Followed
1. Take thick iron rod and cover it with a thick paper and wind
a large number of turns of thin Cu wire on thick paper(say
60) . This constitutes primary coil of transformer.
2. Cover the primary coil with a sheet of paper and wound
relatively smaller number of turns ( say 20) of thick copper
wire on it. This constitutes the secondary coil. It is a step down
transformer.
3. Connect P1 ,P2 to A.C main and measure the input voltage
and current using A.C voltmeter and ammeter respectively.
4. Similarly,measure the output voltage and current through S1
and S2.
5. Now connect S1 and S2 to A.C main and again measure
voltage and current through primary and secondary coil of
step up transformer.
6. Repeat all steps for other self made transformer by changing
number of turns in primary and secondary coil.
 Uses Of Transformers
1. In voltage regulator for T.V. , refrigerator, computer,
air conditioner, etc.
2. A step down transformer in used for welding purposes.
3. A step down transformer is used for obtaining large
current.
4. A step up transformer is used for the production of X –
Rays and NEON advertisement.
5. Transformer are used in voltage regulators and
stabilizied power supplies.
6. Transformer are used in the transmission of a.c. over
long distances.
7. Small transformer are used in radio sets, telephones
,loud speakers and electric bells etc
 Conclusion
1. The output voltage of the transformer across the
secondary coil depends upon the ratio ( Ns/ Np)
with respect to the input voltage.
2. There is a loss of power between input and output
coil of a transformer .
 Precautions
1. Keep safe yourself from high voltage.
2. While taking the readings of current and voltage
the A.C should remain constant.

Sources of error
1. Values of current can be changed due o heating
effect
2. Eddy current can change the readings.
 Bibiliography
1.Ncert textbook class 12
2.Ncert physics lab manuel
3. Internet
4. www.yahoo .com
5. www.scribd.com
6. www.google.com