Scribd
Upload
7 views6 pages

EXAM PART 1 a320

Uploaded by

adrian
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
7 views6 pages

EXAM PART 1 a320

Uploaded by

adrian
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

EXAM PART 1

24 Questions 36 MINUTES

1. The main objective of MPD document is to provide maintenance planning information


necessary for each operator to develop a customized
A. Maintenance program
B. Aircraft maintenance manual
C. Minimum equipment list

Ref : ATA 05 PG 4

2. There are how many major zones for the aircraft?


A. 7
B. 8
C. 9

Ref : ATA 06 PG 16

3. Which jacking point is located forward of the nose landing gear?


A. Point A
B. Point B
C. Point C

Ref : ATA 07 PG 26

4. What is the longitudinal angle corresponds to D4 position in the attitude monitor?


A. 0 degree
B. 45 degrees
C. 90 degrees

Ref : ATA 08 PG 28

5. What is the maximum permitted steering angle on each side of the A/C centerline?
A. 35 degree
B. 45 degree
C. 95 degrees

Ref : ATA 09 PG 35

6. On the overhead panel 25VU, on the CABIN PRESS section, which pushbutton switch
needs to to be push to close the ventilation skin valves and the outflow valves?
A. MAN V/S CTL
B. MODE SL
C. DITCHING

Ref : ATA 10 PG 42

7. Placards and markings are required by the regulation used for the Airbus aircraft type
certification (JAR 25) are identified by a flag note
A. REQUIRED BY REGULATION
B. REQUIRED BY AUTHORITY
C. REQUIRED BY IATA

Ref : ATA 11 PG 2

8. If engine reverser cowls have to be opened for maintenance action, the slats must be
A. Extended
B. Neutral
C. Retracted

Ref : ATA 12 PG 68

9. Purpose of airplane grounding is to electrostatically balance the aircraft during


A. Jacking
B. Towing
C. Refuelling

Ref : ATA 20 PG 2

10. Which one is a damage assessment process follows different carried out on the aircraft:?
A. Damage geographical location
B. Structure identification
C. Allowable damage information,

Ref : ATA 51 PG 300

11. Which area of the fuselage lies between Fr 24 and Fr 35?


A. Forward
B. Center
C. Rear

Ref : ATA 53 PG 52

12. Which frames section comprises the un-pressurized part of the rear fuselage?
A. Fr 70 to Fr 87
B. Fr 77 to Fr 87
C. Fr 70 to Fr 80

Ref : ATA 53 PG 70

13. Which pylon structure is attached to the wing and supported the engine?
A. Primary
B. Secondary
C. Tertiary

Ref : ATA 54 PG 118

14. The center joint of a spar box is made from


A. Steel
B. Composite
C. Titanium

Ref : ATA 55 PG 134

15. There are how many fixed windows installed in the cockpit?
A. Two
B. Four
C. Six

Ref : ATA 56 PG 200

16. Which part of the wing is installed in between the main frames (Fr) 36 and 42 to make an
integral fuel tank?
A. Left outer wing
B. Center wing box
C. Right outer wing

Ref : ATA 57 PG 214

17. Which flight controls is used to achieved roll control?


A. Elevator
B. Ailerons
C. Rudder

Ref : ATA 27A (S) PG 2

18. Which axis is in the direction of the wing span?


A. X
B. Y
C. Z

Ref : ATA 06A PG 2

19. Which locking mechanism blocks the door even if a double mechanical failure in the
locking mechanism?
A. Locking hook
B. Safety pin
C. Spring rod

Ref : ATA 52 PG 24

20. How many exit doors are located in each wing?


A. One
B. Two
C. Three

Ref : ATA 52 PG 40

21. Which mode allows the door to be manually opened without escape slide operation?
A. ARMED
B. NORMAL
C. DISARMED
Ref : ATA 52 PG 52

22. Which hydraulic system is used to operate cargo door?


A. Green
B. Blue
C. Yellow

Ref : ATA 52 PG 60

23. Which component is used to notify cockpit crew of a request for entry or to open the
door in case of confirmed incapacitation of both pilots?
A. Code pad
B. Door switch
C. Buzzer

Ref : ATA 52 PG 110

24. What is the colour of the door symbol on the ECAM DOOR page when the door is
locked?
A. White
B. Amber
C. Green

Ref : ATA 52 PG 134

Extra 30% Question for Set 2&3

1. Where is the location for station 0 for all structural measurements for the X axis?
A. 100 in forward of the A/C nose
B. 254 in forward of the A/C nose
C. 100 in forward of the A/C wing

Ref : ATA 06 PG 02

2. Which jacking point is located outboard of the engine pylons?


A. Point A
B. Point B
C. Point C

Ref : ATA 07 PG 26

3. What is the lateral angle corresponds to D4 position in the attitude monitor?


A. 0 degree
B. 45 degrees
C. 90 degrees

Ref : ATA 08 PG 28

4. When towing using the front fittings to push the A/C rearwards with engine at idle, towing
angle is limited to
A. 20 degrees.
B. 40 degrees
C. 90 degrees

Ref : ATA 09 PG 35

5. Mooring is necessary, if the aircraft points into the wind and wind speed is
A. Between 10 and 30 kts
B. Between 30 and 50 kts
C. Between 50 and 70 kts

Ref : ATA 10 PG 42

6. Where is the location of engine oil access door?


A. Right side of fancowl
B. Left side of fancowl
C. Bottom of fancowl\

Ref : ATA 12 PG 68

7. Which area of the fuselage lies between Fr 35 and Fr 47?


A. Forward
B. Center
C. Rear

Ref : ATA 53 PG 60

8. Which area of the fuselage lies between Fr 47 and Fr 70?


A. Forward
B. Center
C. Rear

Ref : ATA 53 PG 52

9. Which pylon structure is composed of the pylon to wing center fillets?


A. Primary
B. Secondary
C. Tertiary

Ref : ATA 54 PG 128

10. Which of the following enables the adjustment of the angle of incidence of the
Trimmable Horizontal Stabilizer?
A. Hydromechanical actuator
B. Ball nut and jack crew
C. Stabilzer hinge arms

Ref : ATA 55 PG 136

11. Windshields are installed with


A. De-icing system
B. Defogging system
C. Anti-fogging system
Ref : ATA 56 PG 202

12. Top and the bottom surfaces of the outer wing box are made of skin panels machined
from
A. Aluminum alloy
B. Reinforced fiber
C. Composite material

Ref : ATA 57 PG 222

You might also like