Scribd
Upload
9 views

Notes

Uploaded by

sujadilip73
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
9 views

Notes

Uploaded by

sujadilip73
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

Department of Electronics and Communication Engineering

23EEE184 Basic Electrical and Electronics Engineering Practice

Inverting and Non-Inverting Amplifier

Name of the Student

Registration Number

Due Date of Submission: Date of Submission:

Assessment Rubrics
Description Mark Allotted Mark
Secured
Apparatus required and Important definitions 10

Experimentation: Connection, Conduction and 35


Verification
Theoretical Calculations 25

Results and Inference 10

Viva questions 20

Late Submission/Plagiarism Mark Deduction 10

Total Marks 100

Signature of Lab in-charge


Activity Sheet
Inverting and Non-Inverting Amplifier
1. Aim: To realize the Inverting and Non-inverting amplifier using 741 Op-amp

2. Apparatus Required: CRO, Function Generator, Bread Board, 741 IC,

±15V supply, Resistors 1KΩ, 10KΩ, and connecting wires.

3. Theory:

An inverting amplifier using opamp is a type of amplifier using opamp


where the output waveform will be phase opposite to the input waveform. The
input waveform will be amplifier by the factor Av (voltage gain of the amplifier)
in magnitude and its phase will be inverted. In the inverting amplifier circuit the
signal to be amplified is applied to the inverting input of the opamp through the
input resistance R1. Rf is the feedback resistor. Rf and Rin together determine the
gain of the amplifier. Inverting operational amplifier gain can be expressed
using the equation Av = – Rf/R1. Negative sign implies that the output signal is
negated. The circuit diagram of a basic inverting amplifier using opamp is
shown in Fig.1
Fig1: Inverting
Amplifier

In non-inverting operational amplifier configuration, the input voltage signal,


( VIN ) is applied directly to the non-inverting ( + ) input terminal which means
that the output gain of the amplifier becomes “Positive” in value in contrast to
the “Inverting Amplifier” circuit. The result of this is that the output signal is
“inphase” with the input signal. Feedback control of the non-inverting
operational amplifier is achieved by applying a small part of the output voltage
signal back to the inverting ( – ) input terminal via a Rƒ – R1 voltage divider
network, again producing negative feedback. This closed-loop configuration
produces a noninverting amplifier circuit with very good stability, a very high
input impedance, Rin approaching infinity, as no current flows into the positive
input terminal, (ideal conditions) and a low output impedance shown in Fig2.

``
Fig2: Non-Inverting Amplifier
4. Procedure:
1. Assemble the circuit shown in Figure 1 and 2. Use oscilloscope CH1 to
measure Vi and CH2 to measure Vo.
2. Observe and record the input and output voltages using the oscilloscope
noting the phase relationship, peak-to-peak voltages and period. Plot the
graph.
3. Calculate the gain of the amplifier using the corresponding formula.

5. Observation:

Gain= Vout/Vin
6. Model Graph:
Inverting Amplifier:
7. Results & Inference

Viva Questions:
1. Define an integrated circuit and classify them.

2. What is an op-amp and what are its types?


3. Draw the symbol
of op-amp?

4. What are the various terminals of op-amp 741 IC?

5. What is the operating voltage range of IC 741?

You might also like