Classic 2K
Automotive Acrylic 2K PU Topcoat
Product Description
Classic 2K topcoats are premium Automotive topcoats based on polyurethane chemistry. It offers a hard, chemical resistant paint film with superior
gloss that lasts long. The product is available in various shades. It can be stoved at lower temperatures to enhance productivity without compromising
quality. This product has excellent gloss retention, adhesion, hardness, scratch resistance and extremely durable with non-yellowing characteristics.
Typical Use
This product is recommended to use for protection and decoration of all automotive metal substrates.
Technical Data
% Solids By Weight (NVM) 70 +/- 2
% Solids By Volume 59 +/- 2
Colour Brilliant White & Pestle Shades
Gloss @ 60 G. H. Above 90 (After Application)
Specific Gravity (Density/WPL) kg/L 1.25 +/- 0.02
Flash Point Base: ≥26°C Catalyst : ≥15°C
VOC gm/L ≤420
Max Min STD Actual coverage may vary due to
Theoretical Coverage m2/L 19.5 11.8 14.7 the factors like, type of wood, wind
flow, applicators skills and
Dry Film Thickness (DFT in microns) 30 50 40 atmospheric conditions.
Wet Film Thickness (WFT in microns) 50 85 70
Mixing Ratio by Volume 2 Parts Base : 1 Part Catalyst
Thinner Intake 20 – 30% (Acrylic Thinner #45)
Pot Life @ 30°C 5 Hours
Drying Characteristics @ 30°C & ≤85% Humidity
Dust Free 30 Minutes
Tack Free 4 Hours
Full Cure/Packing (Min.) 24 Hours
Recoating Time (Min.) 8 hours
Recoating Time (Max.) Infinite
Base : 12 Months
Catalyst : 6 Months
Shelf Life & Storage
Keep the containers in a dry, cool, well ventilated space and away from direct
sunlight, sources of heat and ignition. Containers must be always kept tightly closed.
Pack Size 3.6L, 18L, 20L
Page 1 of 2
Issued on : Jan’20
Revision : 0
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Material Safety Data Sheet (SDS) for this product.
Classic 2K
Automotive Acrylic 2K PU Topcoat
Application Guidelines
Surface Preparation:
Sand wood surface (New or previously coated) initially with emery paper No. 180 and followed by emery paper No. 220 or 320. Properly
remove all the dust by applying air or using rags and later wipe with PU Thinner. Make sure all the traces oil, dust and grease like
materials removed before application.
Paint System:
Epoxy Primer/ NC Primer/ PU primer – 1 Coat
Polyester Putty / NC Putty – 1 Coat
Classic 2K – 1 or 2 coats
Always sand the surface with fine emery paper before application of subsequent coat until smooth uniform finish is achieved.
Application Tools:
1. Conventional Air Spray: Recommended
2. Brush or Roller : Only where application with spray gun is not possible, but care should be taken to achieve
recommended DFT.
Air Pressure: 40 – 50 bar
Tip Size of spray gun: 1.2mm
Ensure adequate ventilation while spraying and drying
Substrate temperature must be 3°C above dew point
Recommended to mix thinner first with base and then add catalyst
Health & Safety Measures
(Recommended to Read this section before application)
Keep out of reach of children
Recommended to wear overalls, safety goggles and solvent mask while spraying
Avoid contact with skin and eyes.
First-Aid
Eyes : Immediately flush eyes with water and seek medical help
Skin : Use soap & water or appropriate cleaner
Inhalation : Allow to breath fresh air, loose the neckline and keep him/her rested
Ingestion : Obtain medical help without asking for omitting
Disclaimer
The data provided in this sheet is given to the best of our knowledge and based on laboratory testing and practical experience. We
cannot guarantee anything but the product since the conditions and methods during application vary. We reserve the right to
change the given data without prior notice. The product data sheet supersedes those previously issued.
For more information, contact our Liberty Paints Representative or go to www.libertypaintsarabia.com or reach to us on
[email protected]
Page 2 of 2
Issued on : Jan’20
Revision : 0
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Material Safety Data Sheet (SDS) for this product.
