2.

Thermistor:
 Thermistor is a resistive transducer whose resistivity depends upon
surrounding temperature. For this reason it can be used as
Temperature sensor.
 The term Thermistor is a combination of “thermal” and “resistor”
 It is made up of semiconductor material. Thermistor devices are
generally made from oxides of certain metals like Manganese,
Cobalt & Nickel etc.
 There are two types of thermistors: Negative Temperature
Coefficient (NTC) and Positive Temperature Coefficient (PTC).
With an NTC thermistor.
o NTC Type:
In this type when temperature increases, resistance decreases.
Similarly, when temperature decreases, resistance increases.
This type of thermistor is used the most.

o PTC Type:
In this type when temperature increases, the resistance
increases, and when temperature decreases, resistance
decreases.

 Working Principle:
o As the temperature of a thermistor increases its resistance
decreases exponentially.
o The mathematical expression for the relationship between
resistance of thermistor and temperature is
 𝟏 𝟏
𝑹𝑻𝟏 = 𝑹𝑻𝟐 𝐞𝐱𝐩⁡[𝜷 ( − )]
𝑻𝟏 𝑻𝟐
Where,
𝑅𝑇1 = resistance of the thermistor at temperature T1
𝑅𝑇2 = resistance of the thermistor at given temperature T2
β = constant, its value depends upon the material used in the
construction of thermistor, typically its value ranges from
3500 to 4500.
This above equation is known as characteristic equation
of Thermistor
 Thermistor can be made in different shape and sizes. It is available
in the form of the bead, probe, rod and disc etc. The different types
of the thermistor are shown in the figure below.

The bead form of the thermistor is smallest in

shape.

Bead type is enclosed inside the solid glass

rod to form probes.

The disc shape is made by pressing material under

high pressure with diameter range from 2.5 mm to 25mm

It is shaped as a long vertical rod

0.250-2.0 inches (0.63-5.1 centimetres) long and 0.050-0.110
inch (0.13-0.28 centimetre) in diameter, of oxide-binder mix
and sintered; ends are coated with conducting paste and leads
are wrapped on the coated area.
 Advantages
o They are compact and inexpensive.
o They have good stability and high sensitivity.
o Their response is very fast.
 o They are not affected by stray magnetic and electric fields.
Due to all these advantages, thermistors are preferred over
other temperature detecting devices like RTDs and
thermocouples.

3. Resistance Thermometer:
 Resistance thermometers are based on the principle that the
electrical resistance of a metal wire varies with temperature.
 The resistance thermometer is also known as Resistance
Temperature Detector (RTD)
 It uses the resistance of electrical conductor for measuring the
temperature.
 If R0 is the resistance at 0 °C, then the resistance RT at T °C is:

RT = R0 (1 +αT)

Where, α = temperature coefficient of resistance of a particular

material.
 The resistance thermometer uses a sensitive element made of
extremely pure metals like platinum, copper or nickel.
 RTD is a PTC type transducer.

 Construction of Resistive Thermometer

 o The resistance thermometer is placed inside the protective
tube for providing the protection against damage.
o The resistive element is formed by placing the platinum wire
on the ceramic bobbin.
o This resistance element is placed inside the tube which is
made up of stainless steel or copper steel.
o The lead wire is used for connecting the resistance element
with the external lead. The lead wire is covered by the
insulated tube which protects it from short circuit.
o The ceramic material is used as an insulator for high-
temperature material and for low-temperature fibre or glass is
used.
 Advantages:
o It provides highly accurate results.
o RTD provides a vast operating range.
o Due to its high accuracy
o RTD is used in all such applications where precise results are
needed.
 Disadvantages:
o The sensitivity of platinum RTD is very less for the minor
variation in temperature.
o RTD possess slower response time.

4. Strain Gauge:
 A strain gauge is a device used to measure strain on an object.
 Resistance of the device varies with respect to applied force. It
converts force, pressure, tension, weight, etc., into a change in
electrical resistance which can then be measured.
 When an external force is applied on an object, due to which there is a
deformation occurs in the shape of the object. This deformation in the
shape is both compressive or tensile is called strain, and it is measured
by the strain gauge.
 Working Principle:
 Resistance of any conductor wire is directly dependent on the
length and the cross-sectional area of the conductor, given by:

R=ρL/A
Where,
R = Resistance
L = Length
A = Cross-Sectional Area
ρ= Resistivity of the material
The change in the shape and size of the conductor also alters its length and
the cross-sectional area which eventually changes its resistance.

If ΔL is the change in length of the wire by the application of force or

stress then strain (𝜀) is given by:
ΔL
Strain (𝜀) =
𝐿
 Sensitivity of the strain gauge material is given by a parameter
known as Gauge factor (G). The Gauge Factor is the sensitivity
coefficient of strain gauges
 Gauge factor is defined as the ratio of fractional change in electrical
resistance to the fractional change in length (strain):

𝚫𝐑⁄ 𝚫𝐑
𝑹 𝑹
𝑮= 𝚫𝐋⁄ =
𝑳 𝜺

Where,
R=original Resistance of wire
ΔR= change in Resistance
L=original Length of wire
ΔL= change in Length
ΔL
𝜀=
𝐿
 Construction:
The metallic strain gauge consists of a very fine wire or, more commonly,
metallic foil arranged in a grid pattern.
The grid is bonded to a thin backing, called the carrier, which is attached
directly to the test specimen (object). Therefore, the strain experienced by the
test object is transferred directly to the strain gauge and changes the resistance
of the strain gauge.

Backing

Figure: Wire type bonded strain gauge

 Measurement by using Bridge circuit:

The change in resistance in strain gauge can be measured in terms of change
in voltage by connecting the strain gauge in a Wheatstone bridge circuit.

o In this circuit, R1 and R3 arms are equal to each other, and R2 is the
rheostat arm and its value equal to the strain gauge initial resistance.
 o When no force is applied, the gauge is unstrained and the bridge is
balanced. Voltmeter shows zero value at this condition
o When force is applied on the strain gauge resistance of the gauge
changes. As there is a change in resistance of strain gauge, the bridge
gets unbalanced and produces a voltage indication at the voltmeter.
 Application:
o It can be used as Weight, Force, Pressure or Stress sensor.

I. Inductive Transducers
The transducer whose inductance changes with respect to change in input
parameter is known as inductive transducer.
1. LVDT(Linear Variable Differential Transformer):
 The Linear Variable Inductive Transformer converts the linear
displacement into an electrical signal.
 It works on the principle of mutual induction, i.e., the flux of the
primary winding is induced to the secondary winding. The output of
the transformer is obtained because of the difference of the
secondary voltages, and hence it is called a differential transformer.

 Construction of LVDT:

 The basic construction of the LVDT is shown above in the figure.

LVDT consist of a primary winding and two secondary windings S1
and S2. The secondary winding is wound on the cylindrical former.
 The secondary windings have an equal number of turns, and it is
placed identically on both the side of the primary winding.
 The output voltage of the secondary winding S1 is ES1 and that of
the S2 is ES2.
 The secondary voltage signal is converted into an electrical signal
by connecting the secondary winding in series opposition as shown
in the figure above.
 The output voltage of the transducer is determined by subtracting the
voltage of the secondary windings.
Output voltage (E0) = ES1 - ES2
 Working:
The change in output voltage is directly proportional to the
displacement of the core. Any displacement will increase the flux of
one of the secondary winding and on the other hand, reduces the
other which develops a differential voltage at the output. There could
be three possible conditions which are described below:
Condition-I:
o When the soft core moved towards left, the flux linked in S1
is more as compared to S2.
o The output voltage of the winding S1 is more than the S2.
o Since ES1 >ES2, E0 is positive. So E0 is in phase with the
primary voltage.

Condition-II:
o When the soft iron core move towards right the magnitude
of the flux linked S2 is more than S1.
o The output voltage of the winding S1 is less than the S2.
o Since ES1 <ES2, E0 is negative. The output voltage E0 is
180º out of phase with the primary winding.
Condition-III:
o When the soft iron core is at the centre of S1 and S2, the flux
linked in S1 and S2 are same.
o The output voltage of the winding S1 is equal to S2.
o So E0= ES1 -ES2
=0 V
Figure: LVDT Characteristics

The curve between the output voltage and the input displacement is
shown in the figure above.
The curve is linear for small displacement between A & B.

 Uses of LVDT:
o It is used for measuring the displacement having a range from few
mm to cm. The LVDT directly converts the displacement into an
electrical signal.
o The LVDT is used as a device for measuring the force, weight and
pressure. Some of the LVDT used for measuring the load and
pressure.

II. Capacitive Transducers

The transducer whose capacitance changes with respect to change in input
parameter is known as capacitance transducer.
 The working principle of a capacitive transducer is variable
capacitance. It consists of two parallel metal pates which are
separated by dielectric medium (such as air).
  The capacitance of the variable capacitor can be measured by this
formula.

𝝐𝟎 𝝐𝒓
𝑪=𝑨
𝒅
𝝐
𝑪=𝑨
𝒅

C = capacitance of the variable capacitor

𝝐𝟎 = permittivity of free space
𝝐𝒓 = relative permittivity
𝝐 =𝜖0 𝜖𝑟
A = overlapping area between the two plates
d = distance between the two plates
By varying the parameters like A, d & 𝝐𝑟 of the variable capacitor
the capacitance can be changed.
So the capacitive transducer is of three types:
1. Variable Area(A) Capacitive Transducer
2. Variable distance between two plates (d) type capacitive
Transducers
3. Variable dielectric constant (𝝐 )type capacitive Transducers

1. Variable Area Capacitive Transducer:

 In this type capacitive transducer the overlapping area (A) between the
two plates changes due to the application of Displacement, Force or
Pressure.
 Since parameter ‘A’ changes, the capacitance ‘C’ also changes, as ‘C’is
directly proportional to ‘A’.
 𝝐⁡(A−wx)
𝑪=
𝒅

Where, ‘x’ is the displacement of the plate and ‘w’ is the width of the
plate

 It can be used as Displacement, Force or Pressure sensors.

2. Variable distance between two plates type capacitive

Transducers
In this type capacitive transducer the distance (d) / separation between the
two plates changes due to the application of Displacement, Force or
Pressure.

 Since parameter ‘d’ changes, the capacitance ‘C’ also changes, as

‘C’ is inversely proportional to ‘d’.
𝝐⁡
𝑪=𝑨
𝒅+𝒙

Where, ‘x’ is the displacement of the plate

 It can be used as Displacement, Force or Pressure sensors.
Active Transducers
The transducers which do not require any external power supply for the
generation of electrical output (V or I) is known as Active Transducer.
I. Piezoelectric Transducers
 A piezoelectric transducer is a device which can convert mechanical
energy like Force or Pressure into an electrical energy.
 It uses piezoelectric effect for the generation of electric charge.
 It is an active transducer.
Construction and Working:
 Piezoelectric materials like Quartz, Rochelle salt etc can be used to
make the transducer.

 The faces of piezoelectric material, usual quartz, is coated with a

thin layer of conducting material such as silver known as Electrode.
 When stress is applied, the ions in the material move towards one of
the conducting surface while moving away from the other. This
results in the generation of charge.
 This charge is used for calibration of stress. The polarity of the
produced charge depends upon the direction of the applied stress/
force.
 If F is the applied force and Q is the charge developed due to it then
Q ∝ F.
⇒Q = d x F
Where, d is known as piezoelectric coefficient of the material.
 Due to the charge Q, potential difference Vo developed between the
electrodes which can be taken as output.
 This transducer is used as Force, Pressure or Stress sensor.

II. Hall effect Transducers

  A Hall Effect sensor is a transducer that varies its output voltage in
response to a magnetic field.
 This transducer works on the principle of Hall Effect.
 Hall Effect: If a current carrying strip of the conductor is placed in a
transverse magnetic field, then an EMF is developed on the edge of the
conductor. The magnitude of the developed voltage depends on the
density of flux. This property is known as Hall Effect.

𝑩×𝑰
The output voltage of Hall Effect sensor 𝑽𝑯 = 𝑲
𝒕
Where, K= Hall Effect coefficient
B=Magnetic flux density
I= Circuit current
t = Thickness of the conductor strip (Hall Element)
The strip of the conductor is called as Hall element.
Applications of Hall Effect Transducer:
a. Magnetic to Electric Transducer – The Hall effect element is
used for converting the magnetic flux into an electric signal.
b. Measurement of Displacement – The Hall Effect element
measures the displacement of the structural element.
 Consider the ferromagnetic structure which has a permanent magnet.
The hall effect transducer placed between the poles of the permanent
magnet. The magnetic field strength across the Hall Effect element
changes by changing the position of the ferromagnetic field. So
output voltage of the transducer changes with respect to input
displacement.
c. Measurement of Current – The Hall Effect transducer is also used
for measuring the current.
The AC or DC is applied across the conductor for developing the
magnetic field. The strength of the magnetic field is directly
proportional to the applied current. The magnetic field develops the
EMF across the strips.

***************************************************

Chapter-8: OSCILLOSCOPE
CATHODE RAY OSCILLOSCOPE (CRO)
 The cathode ray oscilloscope (CRO) is an electrical instrument which is
used for display, measurement and analysis of waveforms and others and
electrical phenomenon.
 A cathode ray oscilloscope is a very fast X-Y plotter that can display an
input voltage signal versus time.
Working:
 The CRO has the cathode ray tube which acts as a heart of the oscilloscope.
  In an oscilloscope, the CRT produces the electron beam which is
accelerated, decelerated and focus with the help of accelerating and
focusing anode at a high velocity and brings to the focal point on a
fluorescent screen.
 After the collision of the electron on the screen, it produces a visible spot
where the electron beam strikes with it and this spot is seen on another side
of the screen.
 This collision or bombarding of electrons continually done on the screen
which shows the electrical signal, this electron beam like an electrical
pencil of light which produces a light where it collides with the screen.

Major Components of Cathode Ray Oscilloscope

The main blocks of CRO are

 Cathode Ray Tube (CRT)

 Vertical amplifier
 Delay Line
 Trigger circuit
 Time base generator
 Horizontal amplifier
 Blanking circuit
 Power supply

Figure: Block diagram of CRO

1. Cathode Ray Tube (CRT):

 CRT Produces a sharply focused beam of electrons and accelerate it to

a very high velocity.
 CRT consist of the following parts:
 Electron gun
 Deflection plate assembly
 Glass envelope
 Fluorescent screen
 Base, for connections
 This electron beam travels from the electron gun to the screen. The
electron gun consists of a filament, cathode, control grid, accelerating
anodes and focusing anode.
 While travelling to the screen, electron beams passes between a set of
vertical deflecting plates and a set of horizontal deflection plates.
Voltages applied to these plates can move the beam in vertical and
horizontal plane respectively.
 The electron beam then strikes the fluorescent material (phosphor)
deposited on the screen with sufficient energy to cause the screen to
light up in a small spot.
2. Vertical Amplifier:
The input signal is applied to the vertical amplifier. The gain of this amplifier
can be controlled by VOLT/DIV knob. Output of this amplifier is applied to
the delay line.
3. Delay Line:
The delay Line delays the arrival of the input waveform at the vertical
deflection plates until the trigger and time base circuits start the sweep of the
beam.
4. Trigger Circuit:
A sample of the input waveform is fed to a trigger circuit which produces a
trigger pulse at some selected point on the input waveform. This trigger pulse
is used to start the time base generator.
5. Time base (Sweep) Generator:
 This produces a saw-tooth waveform that is used as horizontal deflection
voltage of CRT.
 The rate of rise of a positive going part of the sawtooth waveform is
controlled by TIME/DIV knob.
 The sawtooth voltage is fed to the horizontal amplifier if the switch is in
the INTERNAL position. If the switch is in EXT. position, an external
horizontal input can be applied to the horizontal amplifier.

Figure: Sawtooth Waveform

 It is responsible for horizontal sweep of CRT spot from left hand side of
the screen to right hand side.
 When a sawtooth voltage is applied to horizontal plates and an input signal
is applied to vertical plates, display of vertical input signal is obtained on
the screen as a function of time.
6. Horizontal Amplifier:
This amplifies the saw-tooth voltage. As it includes a phase inverter two
outputs are produced. Positive going sawtooth and negative going sawtooth
are applied to right – hand and left – hand horizontal deflection plates of CRT.
7. Blanking Circuit:
The blanking circuit is necessary to eliminate the retrace that would occur
when the spot on CRT screen moves from right side to left side.
This retrace can cause confusion if it is not eliminate. The blanking voltage is
produced by sweep generator. Hence a high negative voltage is applied to the
control grid during retrace period.
 8. Power Supply:
A high voltage (HV supply) section is used to operate CRT and a low voltage
section (LV supply) is used to supply electronic circuit of the oscilloscope.
Measurement of Voltage, Current, frequency, phase by CRO
Measurement of Voltage:
 The oscilloscope is mainly a voltage measuring device.
 The number of divisions on the voltage axis (Y-axis) is measured and it is
multiplied by the value indicated by the Volts/Div knob on the CRO.
Voltage measured= Total no of Y-axis division × Volts/Div
AC Voltage:
 It is measured from peak-to-peak amplitude which measures the absolute
difference between the maximum point of signal and its minimum point of
the signal
 The sine wave is supplied to the Y input of CRO. By adjusting the Volt/div
knob, obtain a sufficiently large display of signal on the CRO screen.
 The vertical length of the waves from the negative maximum to the positive
maximum is read on the graphic scale of the screen.
 This reading (in div.) is multiplied by the volt/div knob reading to give
peak to peak voltage Vp-p.
 The voltage Vp-p is divide by 2 to give peak ac voltage of the signal.
DC Voltage:
 The DC power supply is connected to Y input of CRO taking care that
positive lead of the cable is connected to +ve terminal and negative to the
–ve of the dc power supply.
 The Volt/div knob is set and the dc power supply is switched ON. A
sufficiently large display of signal (vertical line) on the CRO screen is
obtained by setting Volt/div knob.
 The vertical length of the waves is read on the graphic scale of the screen.
 This reading (in div.) is multiplied by the volt/div knob reading to get the
DC voltage.
Measurement of Current :
 Electrical current cannot be measured directly by an oscilloscope.
However, it could be measured indirectly within scope by attaching probes
or resistors.
  Resistor measures the voltage across the points and then substituting the
value of voltage measured and resistance in Ohm’s law formula and
calculates the value of electrical current.
𝑀𝑒𝑎𝑠𝑢𝑟𝑒𝑑⁡𝑉𝑜𝑙𝑡𝑎𝑔𝑒
𝐶𝑢𝑟𝑟𝑒𝑛𝑡 =
𝑅𝑒𝑠𝑖𝑠𝑡𝑎𝑛𝑐𝑒
Measurement of frequency (Direct Method):
 The sine wave is given to the Y input of CRO whose frequency is to be
measured.
 By adjusting the time/div knob, obtain a sufficiently large display of signal
on the CRO screen.
 Measure the width of one full wave in no of divisions.
 Multiply this measured division with reading of time /div knob. This gives
the time period of applied signal.
Time Period= Total no of X-axis division × Time/Div
 Reciprocal of time period will be the frequency of the applied signal.
𝟏
𝑭𝒓𝒆𝒒𝒖𝒆𝒏𝒄𝒚 =
𝑻𝒊𝒎𝒆⁡𝒑𝒆𝒓𝒊𝒐𝒅

Measurement of Phase & frequency by Lissajous figure method

 A Lissajous figure is displayed pattern on the screen when sinusoidal
signals are applied to both horizontal & vertical deflection plates of CRO.
 This Lissajous figure pattern can be used for the measurement of Phase
difference and frequency of applied signals.
Measurement of Phase:
 When two equal voltages of equal frequency but with a different phase shift
(ϕ) are applied to a CRO we obtain different patterns of Lissajous figure in
the below figure.

Figure: Lissajous figure for 0o phase shift

 When two sinusoidal voltages of equal frequency which are in phase with
each other are applied to the horizontal and vertical deflection plates, the
pattern appearing on the screen is a straight line.

Figure: Lissajous figure for 90o phase shift

 Thus when two equal voltages of equal frequency but with 90° phase
difference are applied to a CRO, the trace on the screen is a circle
 Similarly for different phase differences different type of pattern appears.
Some of them are given below.
  The ellipse pattern of Lissajous figure provides a simple means of
measuring phase difference between two voltages.

Referring to figure, the sine of the phase angle between the voltages is given by:
𝑌1 𝑋1
𝑆𝑖𝑛𝜙 = =
𝑌2 𝑋2
𝑌1 𝑋1
⇒ 𝜙 = sin−1 ( ) = sin−1
𝑌2 𝑋2

Measurement of Frequency Lissajous Patterns

 Lissajous patterns may be used for accurate measurement of frequency.
 The signal, whose frequency is to be measured, is applied to the Y plates.
An accurately calibrated standard variable frequency source is used to
supply voltage to the X plates.
 Suppose sine waves are applied to X and Y plates as shown in the figure
below. Let the frequency of wave applied to Y plates is twice that of the
voltage applied to X plates. This means that the CRT spot travels two
complete cycles in the vertical direction against one in the horizontal
direction.
 In the above case Frequency of Y signal is 2 times (twice) of the X signal
so two loop of pattern appear on the CRO screen.
 Similarly number of loop increases if Y signal frequency increases, which
is indicated below.

The ratio of frequency can be calculated by drawing tangent at top/bottom

and left/right sides.
The ratio of the two frequencies can be given by:
𝑓𝑥 𝑁𝑢𝑚𝑏𝑒𝑟⁡𝑜𝑓⁡𝑡𝑖𝑚𝑒𝑠⁡𝑡𝑎𝑛𝑔𝑒𝑛𝑡⁡𝑡𝑜𝑢𝑐ℎ𝑒𝑠⁡𝑡𝑜𝑝⁡𝑜𝑟⁡𝑏𝑜𝑡𝑡𝑜𝑚
=
𝑓𝑦 𝑁𝑢𝑚𝑏𝑒𝑟⁡𝑜𝑓⁡𝑡𝑖𝑚𝑒𝑠⁡𝑡𝑎𝑛𝑔𝑒𝑛𝑡⁡𝑡𝑜𝑢𝑐ℎ𝑒𝑠⁡𝑒𝑖𝑡ℎ𝑒𝑟⁡𝑙𝑒𝑓𝑡⁡𝑜𝑟⁡𝑟𝑖𝑔ℎ𝑡⁡𝑠𝑖𝑑𝑒

𝑓𝑥 𝑁𝑢𝑚𝑏𝑒𝑟⁡𝑜𝑓⁡ℎ𝑜𝑟𝑖𝑧𝑜𝑛𝑡𝑎𝑙⁡𝑡𝑎𝑛𝑔𝑒𝑛𝑐𝑖𝑒𝑠
⇒ =
𝑓𝑦 𝑁𝑢𝑚𝑏𝑒𝑟⁡𝑜𝑓⁡𝑣𝑒𝑟𝑡𝑖𝑐𝑎𝑙⁡𝑡𝑎𝑛𝑔𝑒𝑛𝑐𝑖𝑒𝑠

Where, 𝑓𝑥 = frequency of signal applied to X

𝑓𝑦 =⁡frequency of signal applied to Y
 The ratio of frequencies when open-ended Lissajous patterns are
obtained can also be found by treating the open ends as half tangencies
as shown in the below


***********************************************************
 ELECTRICAL MEASUREMENT &
INSTRUMENTATION

CHAPTER WISE MODEL QUESTION SET

Prepared by Lect. Rashmita Gouda, Govt. polytechnic, Bargarh

CHAPTER-1
Long Questions
1. Explain deflecting, controlling and damping torque in indicating type
instrument.
2. Explain two type of controlling arrangement in Indicating type Instrument.
3. State the various methods for obtaining damping torque.
4. Explain the damping arrangement in Indicating type Instrument
Short Questions
1. Differentiate between the spring control and gravity control.
2. Why is damping required for an electromechanical measuring instrument
3. Define Reproducibility.
4. What is Deflecting torque?
5. What do you understand by calibration of a measuring instrument?
6. Define precision of measuring instruments.
7. Define sensitivity.
8. Define Accuracy.
9. Define Resolution.
10.Define tolerance of measuring instruments.
11.What is controlling torque?
12. What is the importance of controlling torque in electro-mechanical type
instrument?

CHAPTER-2
Long Questions
1. Explain the operating principle of PMMC type instruments.
2. With a neat diagram explain in detail the construction of PMMC
instrument.
3. Discuss the errors in PMMC type instrument.
 4. What are the shunts and multiplier? Derive the expression for both, with
reference to meters used in electrical circuits.
5. Sketch and explain the working of moving-coil instrument.
6. With necessary diagram explain the working principle of Induction type
Instrument.
7. Explain the working of Dynamometer type Instruments with proper
diagram.
8. Explain the working principle of Rectifier type Instrument.
9. State with example how can you extend the range of voltmeters and
ammeters?
10. A milliammeter of range 0-50 mA is require to measure a load current of
6A. The milliammeter has an internal resistance of 0.35 ohm. Calculate the
value of shunt resistance necessary for it.
11. An ammeter having a range of 0-20A, having an internal resistance of 0.08
ohm is to be used to measure up to a range of 0-200 A. Calculate the value
of shunt resistance required. Show the connection diagram.
12. You have an ammeter of internal resistance 100 ohm, which can measure
a maximum current of 30A. How can you extend the range to measure a
maximum current of 100A. Show the circuit with ammeter.
13. How will you use a PMMC instrument which gives full scale deflection at
50mV potential difference and 10mA current as
i. Ammeter 0-10 A range
ii. Voltmeter 0-250 V range

Short Questions
1. What are the main advantages and disadvantages of PMMC instruments?
2. Why an ammeter should have a low resistance value.
3. What are the advantages of Shunt and Multipliers?
4. What are the advantages of Rectifier type Instrument?
5. What is Rectifier type Instrument?
6. State the purpose of using multipliers in measuring instruments.
7. Why voltmeter is connected in parallel and ammeter is connected in
series?
8. How can the range of ammeter be extended?
9. How can the range of voltmeter be extended?
10.Indicating type instrument converts Electrical energy to which energy
form?

CHAPTER-3
 Long Questions
1. Draw the possible methods of connecting the pressure coil of a wattmeter
and compare the errors. Explain the meaning of ‘compensating winding’
in a wattmeter and show how they help to reduce the error.
2. Explain the working of Dynamometer type Wattmeter with necessary
diagram.
3. Explain the working of Induction type Wattmeter with necessary diagram.
4. What are the errors in Dynamometer type Wattmeter and specify the
methods of their corrections?
5. State different types of errors in Dynamometer type Wattmeter.

Short Questions
1. What is Wattmeter?
2. What is UPF Dynamometer type Wattmeter?
3. What are the errors in dynamometer type Wattmeter?
4. Show the connection diagram of 1-phase wattmeter.

CHAPTER-4
Long Questions
1. Discuss with block diagram, the principle of operation of 1-phase energy
meter.
Short Questions
1. What is creeping error in energy meter?
2. What is Energy meter? What do you mean by 1 Unit in domestic energy
meters?
3. What is the major cause of creeping error in an energy meter?

CHAPTER-5
Long Questions
1. With necessary block diagram explain the principle of operation of
electrical resonance type frequency meter.
2. Explain the working of Mechanical resonance type frequency meter.
3. Explain the working principle of Tachometer.
4. With neat sketch explain the working of a power factor meter.
Short Questions
1. What is the use of tachometer?
2. What is power factor meter?
 3. What is frequency meter?

CHAPTER-6
Long Questions
1. Discuss about an AC bridge used for measurement of capacitance.
2. Explain the measurement of resistance by Loss of Charge method.
3. Explain the working principle of Megger.
4. Explain the working principle of digital multimeter.
5. Explain the measurement of medium resistance by Wheatstone bridge
method.
6. Explain the measurement of capacitance by Schering bridge method.
7. Derive the expression for measurement of unknown inductance by
Maxwell bridge method.
Short Questions
1. What is the function of Multimeter?
2. Classify Resistance.
3. Classify low, medium and high resistance.
4. State two applications of Megger.
5. State the advantage of digital multimeter over analog type.
6. State the balanced equation used in AC Bridges.
7. For measurement of which parameter Schering bridge is used?

CHAPTER-7
Long Questions
1. Derive an expression for gauge factor in terms of Poisson’s ration.
2. What is the use of LVDT? Discuss its basic principle of operation.
3. Explain how LVDT can be used for measurement of displacement.
4. Define Transducer. Discuss the classification of transducer.
5. Explain linear and angular motion potentiometer working principle.
6. What is thermistor? What are the different types of thermistor available
according to shape and size?
7. Explain the working principle of wire Strain gauge with proper diagram.
8. Define Capacitive Transducer and its working principle. Enlist the types of
capacitive type transducers.
9. Explain the working Principle of Variable area type Capacitive Transducer.
10.Explain the working Principle of Variable distance between the plates type
Capacitive Transducer.
 11.Explain the working principle of piezoelectric transducer.
12.Explain the working principle of Hall-effect transducer.

Short Questions
1. What are active and passive transducers? Give examples.
2. What is piezoelectric effect?
3. What is gauge factor?
4. What is the application of LVDT?
5. What is Resistive transducer? Give two examples.
6. What is capacitive transducer? Give two examples.
7. What is Inductive transducer? Give example.
8. What are the application of Strain gauge transducer?
9. What is NTC type temperature sensor?

CHAPTER-8
Long Questions
1. With a block diagram, explain the working of CRO.
2. Explain the working of CRT.
3. How the frequency and phase measured in CRO.
4. Describe the measurement of frequency, phase angle and time delay using
oscilloscope with suitable diagrams and mathematical expressions.
Short Questions
1. What is the function of time base generator in CRO?
2. What is Lissajous figure? Write two application of Lissajous figure