UG4A THRU UG4D

ULTRAFAST EFFICIENT PLASTIC RECTIFIER

Reverse Voltage - 50 to 200 Volts Forward Current - 4.0 Amperes

FEATURES
DO-201AD
♦ Plastic package has Underwriters Laboratories
Flammability Classification 94V-0
♦ Ideally suited for use in very high frequency switching
power supplies, inverters and as free wheeling diodes
1.0 (25.4)
♦ Ultrafast recovery time for high efficiency
MIN. ♦ Soft recovery characteristics
0.210 (5.3)
♦ Excellent high temperature switching
0.190 (4.8)
DIA.
♦ Glass passivated junction
♦ High temperature soldering guaranteed:
0.375 (9.5) 250°C/10 seconds, 0.375" (9.5mm) lead length,
0.285 (7.2)
5 lbs. (2.3kg) tension

MECHANICAL DATA
0.052 (1.32)
0.048 (1.22) 1.0 (25.4) Case: JEDEC DO-201AD molded plastic body over
DIA. MIN.
passivated chip
Terminals: Plated axial leads, solderable per MIL-STD-750,
Method 2026
Polarity: Color band denotes cathode end
Mounting Position: Any
Dimensions in inches and (millimeters)
Weight: 0.045 ounce, 1.2 grams

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Ratings at 25°C ambient temperature unless otherwise specified.

SYMBOLS UG4A UG4B UG4C UG4D UNITS

Maximum repetitive peak reverse voltage VRRM 50 100 150 200 Volts
Maximum RMS voltage VRMS 35 70 105 140 Volts
Maximum DC blocking voltage VDC 50 100 150 200 Volts
Maximum average forward rectified current
I(AV) 4.0 Amps
0.375" (9.5mm) lead length at TL=75°C
Peak forward surge current
8.3 ms single half sine-wave superimposed IFSM 150.0 Amps
on rated load (JEDEC Method) at TL=75°C
Maximum instantaneous forward voltage at 4.0A VF 0.95 Volts
Maximum DC reverse current TA=25°C 5.0
IR µA
at rated DC blocking voltage TA=100°C 300.0
Maximum reverse recovery time (NOTE 1) trr 20.0 ns
Maximum reverse recovery time TJ=25°C 30.0
trr ns
(NOTE 2) TJ =100°C 50.0
Maximum recovered stored charge TJ=25°C 15.0
Qrr nC
(NOTE 2) TJ=100°C 30.0
Typical junction capacitance (NOTE 3) CJ 20.0 pF
Typical thermal resistance (NOTE 4) RΘJA 25.0 °C/W
Operating junction and storage temperature range TJ, TSTG -55 to +150 °C
NOTES:
(1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A
(2) trr and QRR measured at tester: IF=4.0A, VR=30V, di/dt=50A/µs, Irr=10% IRM for measurement of trr
(3) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts
(4) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead length

4/98
 RATINGS AND CHARACTERISTIC CURVES UG4A THRU UG4D
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
FIG. 1 - FORWARD CURRENT
DERATING CURVE 200
TL=75°C
AVERAGE FORWARD RECTIFIED CURRENT,

PEAK FORWARD SURGE CURRENT,

6.0 8.3ms SINGLE HALF SINE-WAVE
RESISTIVE OR INDUCTIVE LOAD
100 (JEDEC Method)
TL, LEAD TEMPERATURE
5.0 0.375" (9.5mm) LEAD LENGTH

AMPERES
4.0
AMPERES

TA, AMBIENT
TEMPERATURE
3.0 P.C.B. MOUNTED 10
0.5 x 0.5” (12 x 12mm)
COPPER PADS
2.0

1.0
1
1 10 100
0 NUMBER OF CYCLES AT 60 HZ
0 25 50 75 100 125 150 175
TEMPERATURE, °C

FIG. 3 - TYPICAL INSTANTANEOUS FIG. 4 - TYPICAL REVERSE LEAKAGE

FORWARD CHARACTERISTICS CHARACTERISTICS

INSTANTANEOUS REVERSE LEAKAGE CURRENT,

100 1,000
INSTANTANEOUS FORWARD CURRENT,

TJ=100°C
TJ=25°C
PULSE WIDTH=300µs 100
10 1% DUTY CYCLE TJ=100°C
MICROAMPERES
AMPERES

10
1
1

TJ=25°C
0.1
0.1

0.01 0.01
0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0 20 40 60 80 100
INSTANTANEOUS FORWARD VOLTAGE, PERCENT OF RATED PEAK REVERSE
VOLTS VOLTAGE, %

FIG. 6 - TYPICAL JUNCTION CAPACITANCE

FIG. 5 - REVERSE SWITCHING 100
CHARACTERISTICS TJ=25°C
RECOVERED STORED CHARGE/REVERSE

60 f=1.0 MHz
IF=4.0A di/dt=150A/µs Vsig=50mVp-p
JUNCTION CAPACITANCE, pF

VR=30V
50
RECOVERY TIME, nC/ns

di/dt=100A/µs
di/dt=20A/µs
40
di/dt=50A/µs
10
30 di/dt=150A/µs
di/dt=50A/µs
20 di/dt=20A/µs

10 trr
Qrr
0 1
0 25 50 75 100 125 150 175 0.1 1 10 100
JUNCTION TEMPERATURE, °C REVERSE VOLTAGE, VOLTS