Scribd
Upload
47 views5 pages

Manual de Instrucciones Separador Magnético Húmedo de Tambor CRS 400X300

Uploaded by

Carolina González
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
47 views5 pages

Manual de Instrucciones Separador Magnético Húmedo de Tambor CRS 400X300

Uploaded by

Carolina González
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Address：Guzhang Industrial Park, Shicheng, Ganzhou, Jiangxi, China

CRS400×300 Lab Magnetic Separator


Operation Manual
1.Application
The CRS drum wet weak magnetic separator is mainly used in metal mineral
processing laboratories. It uses wet method to magnetically separate
fine-grained strong magnetic ore, and the sorting form is downstream. The
CRS drum wet weak magnetic separator is small in size, light in weight, simple
in operation and convenient in maintenance. This equipment is not suitable for
beneficiation test with corrosive liquid.

2.Technical Parameter

Technical Parameters
Drum Size(mm) Φ400*300
Drum surface magnetic field strength(mT) 125 adjustable in stepless
Drum speed(r/min) 25
Rated operating current(A) -3.5
Pole coil temperatureries(℃） <100
Maximum feed size(mm) 2
Power supply(V) 380V/50Hz
Power(Kw) 0.37
Dimensions(mm) 783*600*120
Total weight(kg) 260
Capacity(kg/h) 20-60

3.Structure Introduction and Characteristics


The CRS drum wet weak magnetic separator is composed of the main body of
the magnetic separator and the drum power supply.

Jiangxi Victor International Mining Equipment Co.,Ltd


Address：Guzhang Industrial Park, Shicheng, Ganzhou, Jiangxi, China

The main body of the magnetic separator mainly includes: (1) frame (2)
magnetic drum (3) mining tank (4) spray pipe (5) transmission device (6)
feeding box

The drum power supply is a separate silicon bridge rectifier power supply, and
its output is adjusted through the regulator handle.

1. Frame: Welded by angle steel, it is the supporting part of the whole


machine.

2. Magnetic drum: It is equipped with four excitation coils and magnetic cores,
and an additional magnetic pole without excitation coil is installed on the
discharge side to facilitate the discharge. These five magnetic poles are
fan-shaped and fixed on the mandrel. The cylinder is made of non-magnetic
material aluminum and stainless steel. The fan-shaped coils are connected to
cause the alternating magnetic field polarity on the palm of each magnetic pole.
The mineral particles will flip up to 180 each time they pass through a magnetic
pole. Under the action of magnetic stirring, the quality of magnetic products
can be improved. At one end of the mandrel, there is a square outstretching
structure, which can be used to make the magnetic poles in the drum rotate
around the axis with a hand plate to meet the needs of different minerals.

3. Transmission device: installed on the bottom side of the frame. In order to


reduce the center of gravity of the whole machine, the transmission part is
composed of three-phase AC motor and worm gear and worm gearbox. The
output of the gearbox is transmitted to the drum through the chain to drive the
magnet. The drum rotates (the magnetic poles do not rotate with it), the
rotation speed of the drum is a constant speed of 25 rpm, and the direction of
the drum rotation force is consistent with the direction of the mine.

4. Ore tank: It is welded from aluminum and stainless steel plates and fixed on
the frame with screws; there is an overflow port to maintain the liquid level on
the feeding side of the ore tank, and a connection is provided at the lower part
of the concentrate discharge tank. Concentrate mouth for ore access.

5. Water spray pipe: a copper pipe with holes installed on the frame,
connected with the indoor water source, used for washing the concentrate on
the magnetic drum; the spray angle can be adjusted by rotating the water
spray pipe.

6. Feeding box: The box body is welded by stainless steel plates, and its
function is to ensure the uniformity of feeding.

Jiangxi Victor International Mining Equipment Co.,Ltd


Address：Guzhang Industrial Park, Shicheng, Ganzhou, Jiangxi, China

4.Installation, Use and Maintenance


(1) Installation

After the machine is unpacked, it can be placed on the flat ground in a general
workshop or laboratory, and the packaging grease should be cleaned first, and
the fasteners and electrical components welded in the transportation should be
checked for looseness and fall. After considering the inspection and
maintenance of other supporting equipment Convenient, but also consider the
discharge of power, tap water and waste water. After connecting the
three-phase four-wire power supply, test drive, make the magnetic cylinder
rotate in the direction shown by the red arrow, and observe that each part is
normal. If it is found that the conveying direction of the magnetic cylinder is
opposite, the three wires of the drive motor can be arbitrarily exchanged for
two of them.

(2) use

1. Turn on the power and turn on the power switch. At this time, there is
excitation current output and the power indicator light is on.

2. Turn on the operating switch and the drum will rotate in the normal direction.

3. Rotate and adjust the position of the magnetic pole to make the fan-shaped
magnetic pole set to the desired position, and adjust the voltage regulator
handle to make the output DC current at the desired value. (The limit value is
3.5A)

4. Feed the mine and turn on the spray pipe at the same time. (Water pressure
<0.1Mpa).

5. After feeding the ore, set the operation knob switch to the "off" position to
stop the rotating drum, close the recoil water pipe and spray pipe, and then
drain the tailings.

6. Drain the concentrate.

7. Cut off the excitation power supply and demagnetize.

8. Rinse the tailing tank again and combine these two products into
concentrate products.

9. After the operation is completed, perform a thorough flushing; return the


regulator handle to zero, cut off the power switch, and then cut off the power of

Jiangxi Victor International Mining Equipment Co.,Ltd


Address：Guzhang Industrial Park, Shicheng, Ganzhou, Jiangxi, China

the whole machine, and the test is over.

(3) Maintenance:

1. Before use, carefully check the rotating parts of the equipment, electrical
components, etc., and make sure that the equipment is in a normal state
before use.

2. The continuous working time of this equipment should not exceed 3 hours.

3. Replace the lubricant in the gearbox every six months.

4. During the use of the equipment, if the fuse is blown, it must be checked for
short circuit before replacing it; it is strictly forbidden to use unqualified fuse or
use copper wire to connect directly.

Jiangxi Victor International Mining Equipment Co.,Ltd


Address：Guzhang Industrial Park, Shicheng, Ganzhou, Jiangxi, China

Jiangxi Victor International Mining Equipment Co.,Ltd

You might also like