O R D E R DATA S H E E T

DTW™ de-energized tap changer Reset Form

Customer name Customer PO Project name Date

Transformer data
Please provide the following transformer data as it pertains to the application of the DTW™ de-energized tap changer.

Type: Single phase (1 coil) Single phase (2 coils) Three phase

Is additional documentation being included with this form? e.g. nameplate, wiring, etc. Yes No

Switch application data

Switch electrical requirements Number of tap positions
Please indicate the number of operating positions.
Phase to ground = kV BIL
With appropriate shielding, the maximum suggested BIL is 1050 kV Standard (5 positions)

Between phases = kV BIL If less than 5 positions, please select the contact locations.
With appropriate shielding, the maximum suggested BIL is 1050 kV
A B C D E F
Between adjacent contacts = kV BIL
The maximum suggested voltage is 75 kV and 180 kV BIL. If application requires
B
greater than 180 kV BIL, please refer to the Technical Guide (1ZUA4643-211) or contact C
Hitachi ABB Power Grids. A

Maximum through current: Total = A

Per deck = A
Nominal current rating is 845 A. The maximum continuous overload rating is 1014 A at 15° rise
F
D
Decks per phase
E
Please select one of the following options:
01 View from tank wall

Single
Operation side
Double
Please select one of the following options:
Refer to Figure 03.
Shielding
Please select one of the following options: Left hand
For more information, please contact your Hitachi
Right hand
ABB Power Grids representative.

None Position indication

Please select one of the following options:
Level 1
Numerical (1, 2, 3, 4, 5)
Level 2
Alphabetical (A, B, C, D, E)
Special (no antlers)
Series-Parallel (S-P)
Labels and warnings
Please select one of the following options:

English

Spanish

French

HITACHI ABB POWER GRIDS

Contact support options Shaft dimensions
The standard DTW tap changer stationary contact supports are tin Please populate the following fields with the appropriate
plated. If silver plating is prefered, please select the following dimensions and unit of measure.
option: Refer to Figure 03.
NOTE: Upper dimensions are only required for double deck
Silver plated stationary contact supports (special)
configurations when shaft lengths are not identical.

Operating mechanism handle style Please specifiy unit of measure: in mm

Please select one of the following options:
Alower =
Hand bar (Standard)
Aupper =
10 inch hand wheel (Special) Minimum allowable A dimension is 15.75 inches (400 mm)

16 inch hand wheel (Special) B1lower =

B1upper =
Handle drive rotation
By default, the handle rotation to change the tap from position 1 to B2lower =
position 2 is clockwise (CW). Unless otherwise specified, Hitachi
B2upper =
ABB Power Grids will select the rotation best suited for the
Minimum allowable B1 or B2 dimension is 22.64 inches (575 mm)
application
C=
No preference (Standard)
C2 =
Clockwise “CW”
The C2 dimension is only required if handle is not at Position 1 or 4

Counterclockwise “CCW” Minimum allowable C2 dimension is 15.75 inches (400 mm).

For handles mounted directly to the gearbox, C2 = 0.

Lower deck rotation Refer to Figures 04 and 05.

Please select one of the following options:

TK =
Refer to Figure 02.
L=
Clockwise “CW”
Standard mounting boss is L = 6.50 inches (165 mm)

Counterclockwise “CCW” For the ABB boss, please provide L dimension in 0.25 inch (6 mm) increments

Hitachi ABB Power Grids to provide mounting boss:

Upper deck rotation (double bridging only)
Please select one of the following options: Yes No
Refer to Figure 02. This will be ordered separately but is required for engineering purposes.

Clockwise “CW”
Operation mechanism orientation
Counterclockwise “CCW” These diagrams indicate potential locations for handle drives.
Locations 1 and 4 represent the locations of the decks as well.
Please select the desired location of the handle. Additional notes
B
C may be provided in the Comments section.
A Refer to Figures 04 and 05.

Handle position location: Not Selected

Please indicate location by the number shown on Figure 4 or 5.

F
D
E

E
D
F

A
C
B
02 View from tank wall
Upper: Clockwise rotation shown in Position 1
Lower: Counterclockwise rotation shown in Position 1

02 DTW order data sheet 1ZUA4643-202 r4 7.7.2021

 Level 2 shielding

Level 1 shielding Right hand side

Handle in Position 1
Antlers
No shielding

Upper deck

Left hand side

Handle in Position 6

Lower deck

TK A
C
B2

B1

A
C2

L
03 DTW mechanism as mounted within a transformer
3

7 4 8

5 1 6 5 1 6

2 2

04 Single deck operation mechanism configuration 05 Double deck operation mechanism configuration

7.7.2021 1ZUA4643-202 r4 DTW order data sheet 03

Comments

7.7.2021

Hitachi ABB Power Grids We reserve the right to make technical changes We reserve all rights in this document and in ABB is a registered trademark of ABB
Alamo, Tennessee 38001, USA or modify the contents of this document with- the subject matter and illustrations contained Asea Brown Boveri Ltd. Manufactured
out prior notice. With regard to purchase or- therein. Any reproduction, disclosure to third by/for a Hitachi Power Grids company.
ders, the agreed particulars shall prevail. ABB parties or utilization of its contents – in whole or
1ZUA4643-202 r 4

Inc. does not accept any responsibility whatso- in parts – is forbidden without prior written con-
ever for potential errors or possible lack of in- sent of ABB Inc. Copyright © Hitachi Power
formation in this document. Grids, All rights reserved.

https://www.hitachiabb-powergrids.com/offering/product-and-system/transformer/tap-changers-and-switches