Downloaded from SAE International by Univ of Toronto, Friday, July 30, 2021

FEDERAL SUPPLY CLASS

5935

REV.
C
RATIONALE

REVISION IS REQUIRED TO IMPROVE DRAWINGS, MOVE NOTES TO DESIGN PARAGRAPH TO FOLLOW C1 AS

AS85049™/78

STANDARD FORMAT, REMOVE IMAGES, ADD FINISH TABLE, CLARIFY RESTRICTIONS AND ADD METRIC
EQUIVALENTS .660 (16.76), .020 (0.51) TO FIGURES, AND ADD WASHER – POLYTETRAFLUOROETHYLENE (PTFE)
UNDER MATERIALS REQUIREMENT.

NOTICE

THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS
DOCUMENT AND THE LATEST ISSUE OF AS85049. SEE APPLICATION NOTE 1.
SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.
SAE Executive Standards Committee Rules provide that: “ This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is
entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.”

REAFFIRMED 2021-07
REVISED 2016-11
FIGURE 1 – ACCESSORY CONFIGURATION AND DIMENSIONS
ISSUED 2000-06

THIRD ANGLE PROJECTION

For more information on this standard, visit

https://www.sae.org/standards/content/AS85049/78C/

CUSTODIAN: AE-8/AE-8C1 PROCUREMENT SPECIFICATION: AS85049

AEROSPACE STANDARD
(R) CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, AS85049™/78 REV.
ENVIRONMENTAL, 45°, SHIELD TERMINATION,
CATEGORY 2B, NONSELF-LOCKING SHEET 1 OF 4 C
(MIL-DTL-38999 SERIES III AND IV CONNECTORS)

Copyright © 2021 SAE International

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of SAE.
TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)
Fax: 724-776-0790 Email: [email protected] SAE WEB ADDRESS: http://www.sae.org
 Downloaded from SAE International by Univ of Toronto, Friday, July 30, 2021

FIGURE 1 - ACCESSORY CONFIGURATION AND DIMENSIONS (CONTINUED, SAFETY WIRE HOLES)

TABLE 1 - CONNECTOR SHELL SIZE AND CLAMP SIZE

A MAX. DIA.
ACCESSORY CLAMP SIZE OF
SHELL (SEE TABLE 2) COUPLING B C D L
SIZE 1/ RING ±.062 (1.57) ±.062 (1.57) MAX. (REF.)
09 01 THROUGH 02 .75 (19.1) .398 (10.1) 3.088 (78.4) 3.06 (77.72) 3.31 (84.07)
11 01 THROUGH 03 .85 (21.6) .458 (11.6) 3.148 (80.0) 3.20 (81.28) 3.45 (87.63)
13 02 THROUGH 04 1.00 (25.4) .518 (13.2) 3.208 (81.5) 3.34 (84.84) 3.59 (91.19)
15 02 THROUGH 05 1.15 (29.2) .588 (14.9) 3.298 (83.8) 3.49 (88.65) 3.74 (95.00)
17 02 THROUGH 06 1.25 (31.8) .678 (17.2) 3.408 (86.6) 3.71 (94.23) 3.96 (100.58)
19 03 THROUGH 07 1.40 (35.6) .868 (22.0) 3.598 (91.4) 4.01 (101.85) 4.32 (109.73)
21 03 THROUGH 08 1.55 (39.4) .868 (22.0) 3.598 (91.4) 4.13 (104.90) 4.38 (111.25)
23 03 THROUGH 09 1.65 (41.9) .958 (24.3) 3.748 (95.2) 4.36 (110.74) 4.61 (117.09)
25 04 THROUGH 10 1.85 (47.0) .958 (24.3) 3.748 (95.2) 4.41 (112.01) 4.66 (118.36)

1/ SEE REQUIREMENT 2.

TABLE 2 - CLAMP SIZE AND DIMENSIONS

WIRE BUNDLE
CLAMP ACCOMMODATION RANGE Y DIM.
SIZE MIN. 1/ MAX. 1/ MAX.
01 .062 (1.57) .125 (3.18) .80 (20.3)
02 .125 (3.18) .250 (6.35) 1.00 (25.4)
03 .250 (6.35) .375 (9.53) 1.10 (27.9)
04 .375 (9.53) .500 (12.70) 1.20 (30.5)
05 .500 (12.70) .625 (15.88) 1.25 (31.8)
06 .625 (15.88) .750 (19.05) 1.40 (35.6)
07 .750 (19.05) .875 (22.23) 1.50 (38.1)
08 .875 (22.23) 1.000 (25.40) 1.65 (41.9)
09 1.000 (25.40) 1.125 (28.58) 1.75 (44.5)
10 1.125 (28.58) 1.250 (31.75) 1.90 (48.3)

1/ SEE REQUIREMENT 2.

AEROSPACE STANDARD
(R) CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, AS85049™/78 REV.
ENVIRONMENTAL, 45°, SHIELD TERMINATION,
CATEGORY 2B, NONSELF-LOCKING
SHEET 2 OF 4 C
(MIL-DTL-38999 SERIES III AND IV CONNECTORS)