A.

GENERAL NOTES
1.IN THE INTERPRETATION OF THIS DRAWINGS,INDICATEDDIMENSIONSSHALL 7.THE REQUIREDLENGTH OF LAP FOR COMPRESSIONSPLICES SHALL BE AS LEGEND:
SHOWN IN TABLE 4. TABLE 6
GOVERNAND DISTANCESOR SIZES SHALL NOT BE SCALEDFOR CONSTRUCTION 100 150
PURPOSES.THE STRUCTURAL DRAWINGS WITH
SHALL BE USED IN CONJUNCTION SCHEDULE OF CONCRETE HOLLOW BLOCK REINFORCEMENT Sj = 100mm O.C.
MECHANICAL,ELECTRICALAND CIVIL
THE ARCHITECTURAL,
THE SPECIFICATIONS, TABLE 4 REINFORCEMENTS
DRAWINGS. THICKNESS NOTE
LENGTH OF LAP COMPRESSION (mm) (mm) Sh = 100mm O.C. (SEE COLUMN SCHEDULE FOR TIES)
HORIZONTAL VERTICAL
2-10mm∅ HOR. BAR 2-12mmØ HOR. BAR (APPLICABLE ONLY FOR Sj AND Sh)
2.THE CONTRACTOR SHALL COORDINATEWITH THE AR, ME, SE, EE AND OTHER BAR SIZE f'c = 28.0 MPa f'c = 34.5 MPa f'c = 21 MPa A. MINIMUM LAP SPLICE - 30mmØ
UTILITIESAND EQUIPMENTPLANS FOR THE EXACTSIZE, NUMBERAND LOCATIONS (mm) (4000 psi) (5000 psi) 3000 psi B. PROVIDE 1-180mm VERTICAL BAR @ Sw = 150mm O.C. (SEE COL. SCHEDULE FOR TIES)
OF ALL THE SLEEVESOR OPENINGTHRU FLOORSLABS,BEAMSAND WALLSAND 100 10mmØ @ 600mm O.C. 10mmØ @ 400mm O.C. CORNERS INTERSECTION END OF
ALSO DIMENSIONS. 16Ø 320 320 320 Lv = PART OF COLUMN BEYOND CONFINEMENT REGION
WALLS AND EACH SIDE OF OPENING.

400

400
3.ALL REINFORCEDCONCRETEWORK SHALL BE DONE IN ACCORDANCE WITHTHE 20Ø 600 600 600 C. WHERE CHB WALLS ADJOIN COLUMNS 10mmØ @150mm O.C.
RC BEAMS & WALLS DOWELS WITH 10mmØ @150mm O.C. Lo = CONFINEMENT REGION
ACI-318-95 BUILDINGCODE, AND ALL STRUCTURALSTEEL WORK SHALL BE (TYPICAL) ALTERNATELY
25Ø 750 750 750 THE SAME SIZE AS VERTICAL OR (TYPICAL) = MAXIMUM COLUMN DIMENSION BUT NOT LESS THAN ONE-SIXTH
DONE IN ACCORDANCE (LATESTEDITION)IN SO FAR
WITH AISC SPECIFICATIONS 150 10mmØ @ 600mm O.C. 12mmØ @ 400mm O.C. PLACED (FOR 3m CMU
HORIZONTAL REINFORCEMENT SHALL ALTERNATELY CLEAR HEIGHT OF COLUMN FOR 450mm
AS THEY DO NOT CONFLICT WITH THE LOCAL BUILDING CODE REQUIREMENTS. 28Ø 820 820 820 WALL HEIGHT)
BE PROVIDED. PLACED (FOR 3m CMU
32Ø 950 950 950 D. LINTEL SHALL BEAR AT LEAST 18 WALL HEIGHT)
4.THE CONTRACTORSHALL PROVIDEALL MEASURESNECESSARY TO PROTECTNEW
THIS SHALL INCLUDEBUT NOT LIMITEDTO BRACING
EXISTINGCONSTRUCTION. 36Ø 1050 1050 1050 INCHES (400mm) ON EACH SIDE OF
AND SHORING FOR LOADS IMPOSED DURING CONSTRUCTION. 200 12mmØ @ 600mm 12mmØ @ 400mm MASONRY WALL OPENINGS.
O.C. O.C. E. PROVIDE POST AND LINTEL BEAM
8. CLEAR CONCRETE COVER FOR REINFORCING BARS SHALL BE AS FOLLOWS:
5.ALL DIMENSIONSSHALL TAKE PRECEDENCEOVER SCALE SHOWN ON @3000mm O.C. STAGGERED SPLICES STAGGERED SPLICES
SECTIONS AND DETAILS. A. CONCRETE CAST AGAINST EARTH - 75mm FOR COLUMN BARS FOR COLUMN BARS

6.GENERALNOTES AND TYPICALDETAILSAPPLY TO ALL DRAWINGSOTHERWISE

B. CONCRETE EXPOSED TO EARTH
20mmØ TO 36mmØ BARS - 50mm
04 TYP. CHB STIFFENER BEAM DETAIL
SCALE NTS FIN. FLR. LEVEL
SHOWN OR NOTED. 16mmØ BARS AND SMALLER - 40mm FIN. FLR. LEVEL
C. CONCRETE NOT EXPOSED TO EARTH OR WEATHER 1 1 1
7. ALL DIMENSIONS ARE IN METRIC UNLESS OTHERWISE NOTED. SLABS, WALLS,JOINTS - 20mm CONCRETE POST 6
6 6
BEAMS ANDCOLUMNS - 40mm
B. NOTES ON CONCRETE MIXES AND PLACING: D. NOTES ON FOUNDATION 1in 6 OFFSET 1in 6 OFFSET
1.UNLESS OTHERWISEINDICATEDIN PLANS OR NOTED IN THE SPECIFICATIONS, CONCRETE POST MAXIMUM MAXIMUM
THE MINIMUM28-DAYS CYLINDERCOMPRESSIVESTRENGTHOF CONCRETE 1.PROVIDE TEMPORARYREMOVAL OF WATER FROM ANY SOURCE DURING 400
SHALL BE AS FOLLOWS: CONSTRUCTION DEWATERINGSHALL BE CAREFULLYAND PROPERLYPERFORMED CONT. L-SHAPED DOWEL BARS TO 2-16mmØ VERT. BAR
TO AVOID DISTURBING THE FOUNDATIONS AND SLAB BEARING SURFACES. MATCH CHB HOR. BARS
1.1. FOUNDATION 24 MPa ( 3500 psi ) (b) TYPICAL SPLICE & OFFSET DETAIL OF COLUMN BARS

100
CONT. L-SHAPED DOWEL
1.2. COLUMNS & RC WALLS 2.CONTRACTOR SYSTEMSAS
SHALL DESIGN,INSTALLAND MONITOREXCAVATIONS
REQUIREDFOR PROTECTIONOF ADJACENTPROPERTIESAND PROVIDE ALL ALTERNATELY INSTALLED
1.2.1. FOUNDATION TO ROOF BEAMS
LEVEL 24 MPa ( 3500 psi ) 90 DEG HOOK
MEASURES AND PRECAUTIONSNECESSARYTO MINIMIZE SETTLEMENTAND TO MATCH CHB HOR. 10mmØ TIES @150mm O.C. TO C.L (TYP.)
FOR SIZE AND SPACING BARS
1.3. SLAB-ON-GRADE ,HALLWAY,AND OTHER STRUCTURAL ELEMENTS PREVENT DAMAGE TO ADJACENT EXISTING OR NEW CONSTRUCTION. OF HOR. & VERT. BARS, CHB VERT. ALTERNATELY PLACED (FOR 5m CMU WALL HEIGHT)
REINFORCEMENT
SEE SCHEDULE OF FOR SIZE AND SPACING OF HOR. &
21 MPa ( 3000 psi )
3.PREPARE CONDITIONSOF CONCRETE SUPPLY AND PLACEMENTOF THE CONCRETE HOLLOW VERT. BARS, SEE SCHEDULE OF
BLOCK REINF. 400 40
COMPLETE FOUNDATIONFOR THE FULL THICKNESS AS A CONTINUOUS CONCRETE HOLLOW BLOCK
MONOLITHIC CASTING. Sh
C. NOTES ON REINFORCING STEEL BARS: REINF.

CHB WALL 50
STEEL BARS SHALL BE NEW BILLET, HOT ROLLED,WELDABLE,
1.ALL REINFORCING

150
4.SEE TYPICALDETAILOF LIMITINGSLOPE OF ADJACENTFOOTINGAT DIFFERENT Sh Io
DEFORMEDBARS CONFORMING TO THE SPECIFICATIONSOF PNS 49;2001 (ASTM CHB WALL
615) WHOSE GRADE IS SHOWN ON TABLE BELOW. ELEVATION. (REFER TO DRAWING 1) 40mm COVER TO
(a) CORNER WALL (b) INTERSECTION WALL 4-16mmØ VERT. BARS W/ 1-10mmØ TIES COL. TIES (TYPICAL)
@150mm TO CL. (TYPICAL)
TABLE 1 (FOR 4m CMU WALL HEIGHT) COLUMN VERTICAL
GRADE BARS REINFORCEMENT
GRADE 33
(fy = 227 MPa) 10mmØ & LARGER
CONCRETE CHB WALL
FOR SIZE AND SPACING OF TYPICAL STIFFENER (c) DETAIL OF REINFORCEMENTS OF TIED COLUMN AT TOP
POST HOR. & VERT. BARS, SEE
SCHEDULE OF CONCRETE
05 COLUMN DETAIL ON CHB WALLS
SCALE NTS
2.THE SUPPLEMENTARY OF WELDABLEDEFORMEDREINFORCING
REQUIREMENTS HOLLOW BLOCK REINF. 06 TYPICAL COLUMN BAR DETAILS
SCALE NTS
BARS SHALL BE AS FOLLOWS: (c) END WALL
1
2.1. THE MAXIMUM YIELD STRENGTH OF WELDABLE
BARS = 276 MPa (FOR GRADE 40) CONT. DOWEL BARS TO MATCH CHB HOR. BARS
G. NOTES ON COLUMNS: 2. LAP SPLICES,WHEN REQUIRED,ARE PERMITTEDONLY WITHINTHE CENTEROF THE COLUMN
2 LENGTHAND SHALL BE PROPORTIONED AS TENSIONSPLICES.IN NO CASESHALL THE LAP
2.2.THE TENSILE STRENGTHSHALL NOT BE LESS THAN 1.25 TIMES THE 1. WHERE COLUMNS CHANGE IN SIZE, VERTICAL REINFORCEMENTS SHALL BE OFFSET AT A SLOPE NOT
ACTUAL YIELD STRENGTH. SPLICE BE LOCATEDCLOSERTHAN A DISTANCEEQUALTO THE MAXIMUMCOLUMNDIMENSION
MORE THAN 1 IN 6. PROVIDE TRANSVERSE REINFORCEMENT AS PER ITEM BELOW FOR JOINTS WITH FROM THE FACE OF THE BEAM-COLUMNJOINT. PROVIDEEXTRATRANSVERSEREINFORCEMENT
3.ALL CONCRETEREINFORCEMENT SHALL BE DETAILED,FABRICATED,LABELED, DETAIL OF LIMITING BAR OFFSET (AS SHOWN ON DRAWING 1). OF THE SAME SIZE AND ARRANGEMENT INDICATEDIN THE COLUMNSCHEDULESPACED
MOST ONE-FOURTHTHE MINIMUMCOLUMNSECTIONDIMENSIONTHROUGHOUT THE LENGTH
SUPPORTEDAND SPACEDIN FORMS,SECUREDIN THE REQUIREDLOCATIONIN
ACCORDANCE WITH THE PROCEDURESAND REQUIREMENTS OUTLINEDIN THE
01 SLOPE OF ADJACENT FOOTINGS
SCALE NTS DOWEL DOWEL STEEL RATIO AT ANY SECTION WITHIN THIS
PROVIDE EXTRA TIES
@100mm O.C. ON SPLICES THE SPLICE OR 100mm.
LATEST EDITION OF THE BUILDING CODE AND THE MANUAL OF STANDARD REGION SHOULD NOT EXCEED 8% 3. FOR ALL TIED COLUMNS,PROVIDETRANSVERSEREINFORCEMENT OF THE SAME SIZE AND
PRACTICE FOR DETAILING REINFORCED CONCRETE STRUCTURES, ACI-315. E. NOTES ON SLAB-ON-GRADE (d) INTERSECTING R.C. COLUMN OR WALL ARRANGEMENT INDICATEDIN THE COLUMNSECTIONSCHEDULEAND SPACEDNO GREATERTHAN
BARS SHALL BE CLEANEDTHOROUGHLY
4.ALL REINFORCING OF ALL LOOSERUST, CLASS B ONE-QUARTERTHE MINIMUMCOLUMNSECTIONDIMENSIONNOR 100mm, OVERA DISTANCE
1.THE SOIL SUBGRADEAND FILL LAYERSBELOWALL SLABS ON GRADE,PAVING TENSION SPLICE FROMEACH JOINT FACE OF NOT LESS THANTHE LARGEROF THE MAXIMUMCOLUMNSECTION
SOIL OR OTHER MATERIAL IMMEDIATELY PRIOR TO PLACING CONCRETE. IN LAYERS.
AND PIT SLABS SHALL BE WELL COMPACTED DIMENSION, OR ONE-SIXTH OF THE CLEAR HEIGHT OF THE COLUMN OR 450mm.
WHEN USED LOCATE LAP SPLICE NEAR MID
5.THE REQUIREDLENGTH OF LAP FOR TENSION SPLICES IS BASED ON THE 2.ALL SLABS ON GRADESHALL BE PROVIDEDWITH A MINIMUMOF 100mm THK HEIGHT OF COLUMN BUT NOT CLOSER THAN MAX. 3. UNLESS OTHERWISEDETAILED,TYPICALBAR DETAILSFOR TIED COLUMNSARE AS SHOWNIN
DEVELOPMENTLENGTH,LD. SHOWN IN THE TABLE 2 AND TABLE 3 FOR RC
BEAMS AND GIRDERS, RESPECTIVELY AND ON THE FOLLOWING CLASSIFICATIONS:
COMPACTED CLEAN COARSE SAND BED. TYP. CONNECTION DETAIL OF CONCRETE COLUMN DIMENSION FROM FACE TO JOINT Sh DRAWING 1.
3.UNLESS OTHERWISENOTED, ALL BEDDED SLABS SHALL BE REINFORCEDWITH
MASONRY UNITS AT COLUMN AND/OR WALLS

Lo
02
10mm BARS AT 300mm O.C. EACH WAY AT THE CENTER OF SLAB. SCALE NTS Sh/2 Sj = 100mm O.C.
TENSILE SPLICES
CLASSIFICATION SPLICE LENGTH Sj

LI
4.PLACECONCRETEFOR ALL SLABSON GRADEIN CHECKERBOARD FASHIONBETWEEN Sh = 100mm O.C. (USE COLUMN SCHEDULE FOR TIES)
CLASSA 1.0 LD CONSTRUCTIONJOINTSIN AREASNOTTOEXCEED 300 sq. m. WITH A MINIMUMOF
CLASSB 1.3 LD Sh/2 (APPLICABLE ONLY FOR Sj AND Sh)
24 HOURS BETWEENADJACENTAREAS OF PLACEMENT.CONSTRUCTIONJOINTS MINIMUM STAGGERED SPACING WHEN

Lo
SHALL NOTBE FARTHER APART THAN 8m IN ANY DIRECTION. ALL SLABS ON GRADE Sh
WELDED SPLICES OR MECHANICAL Sw = 150mm O.C. (SEE COLUMN SCHEDULE FOR TIES)
SHALL BE SAW CUT ON EACH GRID LINE AND MID BAY LINE (IN BOTH DIRECTION) ELASTIC SEALANT CONNECTOR ARE USED
WITHIN 24 HOURS AFTER CASTING.
CHB WALL Lv = PART OF COLUMN BEYOND CONFINEMENT REGION

H
POLYURETHANE
BACKING
BARS WITH AT LEAST300mm OF CONCRETECAST
6.TOP BARS ARE HORIZONTAL F. NOTES ON MASONRY WALLS Lo = CONFINEMENT REGION

MIN.
600

Lv
BELOW IT. R.C. COLUMN/ = MAXIMUM COLUMN DIMENSION BUT NOT LESS THAN ONE-SIXTH
Sw = SPACING INDICATED ON CLEAR HEIGHT OF COLUMN OR 450
1.ALLMATTERSAND WORKMANSHIP SHALLBE IN ACCORDANCEWITH THE APPLICABLE R.C. WALL

MIN.
COLUMN SCHEDULE

Sw
OF THE NATIONALCONCRETEMASONRYASSOCIATION
AND SPECIFICATIONS
BUILDING CODE. CHB VERT. REINF.
TABLE 2 (SEE SCHED. OF REINF.) Sh = ONE-FOURTH OF THE MINIMUM COLUMN
2. CONCRETE MASONRY UNITS SHALL CONFORM TO ASTM C90 GRADE N. 1-16mmØ EXTRA

Lo
DIMENSION BUT NOT MORE THAN 100mm
DEVELOPMENT LENGTH, Ld, IN TENSION VERT. REINF. Sh/2
CHB HOR. REINF.
f'c = 28.0 MPa f'c = 34.5 MPa f'c = 21 MPa 3. MORTAR AND GROUT FOR ALL REINFORCED MASONRY SHALL CONFORM TO (SEE SCHED. OF REINF.)
(4000 psi) (5000 psi) (3000 psi) ASTM-270 TYPE SHALL HAVE A MINIMUM 28-DAYS STANDARD CYLINDER
BAR SIZE COMPRESSIVEOF 17.5 MPa psi.
(mm) TOP BARSOTHER BARSTOP BARSOTHER BARSTOP BARSOTHER BARS
(mm) (mm) (mm) (mm) (mm) (mm) 4. ALL MASONRY WALL SHALL BE REINFORCED ACCORDING TO THE FOLLOWING
03 WALL REINFORCING AT R.C.COLUMN/WALL
SCALE NTS
Sj = Sh

H/2
SCHEDULE OF CONCRETE HOLLOW BLOCK REINFORCEMENT UNLESS OTHERWISE BUNDLED COLUMN REINF. CONSISTING OF
16Ø 592 300 529 300 684 275 INDICATED IN THE PLANS PLANTED REINF. CUT-OFF BUNDLED BAR REINF.
5.ALL CELLS CONTAININGREINFORCINGBARS OR INSERTS SHALL BE SOLIDLY FILLED WITH AS SHOWN
20Ø 740 500 662 450 854 425 CONCRETE GROUT.
25Ø 925 780 827 700 1026 650
6.FOR TYPICAL CONNECTIONDETAILS ON MASONRYUNITS, REFER TO DRAWINGS3 TO (a) TYPICAL TIED COLUMN BAR DETAIL
28Ø 1036 980 927 870 1196 835 RESPECTIVELY.

1 CONSTRUCTION NOTES AND MASONRY DETAILS

S-1 SCALE NTS

ARCHITECT OF RECORD: PROJECT NAME: APPROVED BY: CONFORMED BY: NO. DATE ISSUE / REVISION SHEET CONTENTS: DWG NUM:
1 00-00-00 FOR REVIEW & COMMENTS - 1
RUSSELL M. DERECHO
CIVIL ENGINEER
PROPOSED THREE (3)-STOREY RESIDENTIAL BUILDING WITH MS. GRACE MERCADO 2 FOR BIDDING / PROJECT PACKAGING
SHEET CONTENTS:
ST
TIN :
PRC. No. 0089359 Date: APR. 09, 2022
TWO (2)-STOREY MAID AND DRIVER'S QUARTER OWNER DEVELOPER
3 - FINAL ISSUE AND PERMIT 001

PTR No. 6493600 Date: Jan. 13, 2022 SHEET

LOCATION: BANGKAL, DAVAO CITY DATE: DATE:
IAPOA No. Location: DAVAO CITY SCALE: OF