SNC10HW Series

10W 4:1 Regulated Single & Dual output

Features
 Reinforced Insulation for 250Vrms Working Voltage
 Compact DIP-24 Package
 Wide 4:1 Input Range
 Isolation Voltage up to 5000VAC
 Over Voltage Protection
 Over Load Protection
 Continuous Short Circuit Protection
 Remote On/Off Control
 Under Voltage Protection
 Soft Start
 No minimum load required
 Efficiency up to 89%
 -40~100°C Operation Temperature Range

PART NUMBER STRUCTURE

SNC 10 H W - 24 05 S
⑴ ⑵ ⑶ ⑷ ⑸ ⑹ ⑺

(1) Series (5) Input Voltage Range (7) Output Type

12 - 4.5-18 V S - Single Output
(2) Watt 24 - 9-36 V D - Dual Output
10 - 10 W 48 - 18-75 V

(3) High Isolation (6) Output Voltage

05 - 5.0 V
(4) Wide Input Range 12 - 12 V
W - 4：1 15 - 15 V

Schmid Multitech GmbH Weinbergstraße 60b, 93105 Tegernheim - Germany www.schmid-m.com

The Copyright and authority for the interpretation of the products are reserved by SCHMID-M. Specifications subject to change without notice.
 ALL SPECIFICATIONS ARE TYPICAL AT 25°C, NOMINAL INPUT AND FULL LOAD UNLESS OTHERWISE NOTED
INPUT INPUT Current OUTPUT OUTPUT Current EFFICIENCY Capacitive

MODEL NUMBER Voltage Range No-Load Full Load Voltage Min. load Full load @FL Load @FL

(Vdc) (mA, typ.) (mA, typ.) (Vdc) (mA) (mA) (%, typ.) (μF, max.)

SNC10HW-1205S 12 (4.5-18) 20 987 5 0 2000 84.5 3300

SNC10HW-1212S 12 (4.5-18) 20 964 12 0 833 86.5 470

SNC10HW-1215S 12 (4.5-18) 20 947 15 0 666 88 390

SNC10HW-1205D 12 (4.5-18) 20 987 ±5 0 ±1000 84.5 ±1470

SNC10HW-1212D 12 (4.5-18) 20 962 ±12 0 ±416 86.5 ±680

SNC10HW-1215D 12 (4.5-18) 20 947 ±15 0 ±333 88 ±390

SNC10HW-2405S 24 (9-36) 6 488 5 0 2000 85.5 3300

SNC10HW-2412S 24 (9-36) 6 474 12 0 833 88 470

SNC10HW-2415S 24 (9-36) 6 468 15 0 666 89 390

SNC10HW-2405D 24 (9-36) 6 488 ±5 0 ±1000 85.5 ±1470

SNC10HW-2412D 24 (9-36) 6 473 ±12 0 ±416 88 ±680

SNC10HW-2415D 24 (9-36) 6 468 ±15 0 ±333 89 ±390

SNC10HW-4805S 48 (18-75) 4 244 5 0 2000 85.5 3300

SNC10HW-4812S 48 (18-75) 4 237 12 0 833 88 470

SNC10HW-4815S 48 (18-75) 4 237 15 0 666 88 390

SNC10HW-4805D 48 (18-75) 4 244 ±5 0 ±1000 85.5 ±1470

SNC10HW-4812D 48 (18-75) 4 237 ±12 0 ±416 88 ±680

SNC10HW-4815D 48 (18-75) 4 237 ±15 0 ±333 88 ±390

Schmid Multitech GmbH Weinbergstraße 60b, 93105 Tegernheim - Germany www.schmid-m.com

The Copyright and authority for the interpretation of the products are reserved by SCHMID-M. Specifications subject to change without notice.
INPUT SPECIFICATIONS
Parameter Conditions Min. Typ. Max. Unit

12V Input 4.5 12 18

Input Voltage Range 24V Input 9 24 36 VDC
48V Input 18 48 75
Module ON 4.2
12V Input
Module OFF 3.5
Module ON 8.6
Under Voltage Protection 24V Input VDC
Module OFF 7
Module ON 17.8
48V Input
Module OFF 16
Input Filter Pi Type
Input Reflected Ripple Current (1) 20 mApk-pk
Start up Time Nominal Vin and constant resistive load 30 ms
Module ON (Open Circuit) 0 1.2
VDC
Module OFF 2.2 12
Remote ON/OFF Control (2)
OFF Idle Current 2.5
mA
CTRL Pin Input Current -0.5 1.0
12V Input 5
Recommended input fuse ( slow blow ) 24V Input 2 A
48V Input 1
Note：
1. Measured with a simulated source inductance of 12μH and a source capacitor Cin ( 47μF, ESR<1.0Ω at 100kHz ).
2. The remote on/off control pin is referenced to –Vin ( pin2 ).

ABSOLUTE MAXIMUM RATINGS

Parameter Conditions Min. Typ. Max. Unit
12V Input 25
Input Surge Voltage ( 100 ms ) 24V Input 50 VDC
48V Input 100
Soldering Temperature 1.5mm from case 10sec max. 260 °C
Note：These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability.

Schmid Multitech GmbH Weinbergstraße 60b, 93105 Tegernheim - Germany www.schmid-m.com

The Copyright and authority for the interpretation of the products are reserved by SCHMID-M. Specifications subject to change without notice.
OUTPUT SPECIFICATIONS
Parameter Conditions Min. Typ. Max. Unit

Output Voltage Accuracy -1 +1 %

Output Voltage Adjustability ( Trim ) -10 +10 %
Line Regulation -0.5 +0.5 %
Single Output -0.5 +0.5
Load Regulation From 0% to 100% Load %
Dual Output -1 +1
Cross Regulation Asymmetrical Load 25% / 100% for Dual Output -5 +5 %
5V Output 30
Ripple & Noise (1) 20MHz bandwidth mVpk-pk
12V & 15V Output 40
5V Output 6.2
Over Voltage Protection
12V Output 15 VDC
(Zener diode clamp)
15V Output 18
Over Current Protection 160 % of FL
Short Circuit Protection Indefinite ( hiccup ) ( Automatic Recovery )
Temperature Coefficient -0.02 +0.02 %/°C
Capacitive Load Minimum Vin and constant resistive load See Table
Transient Recovery Time All models 250 μs
Nominal Vin and
25% load step change 5V Output -5 +5
Transient Response Deviation ( 75%-50%-25% of Io ) %
12V & 15V Output -3 +3
Note：
1. Measured with a 10μF ceramic capacitor.

GENERAL SPECIFICATIONS
Parameter Conditions Min. Typ. Max. Unit
Isolation Voltage Input-output, and rated for 60sec 5000 VAC
Isolation Resistance Input-output 1 GΩ
Isolation Capacitance Input-output 17 pF
Leakage Current 240VAC, 60Hz 2.0 μA
Clearance/Creepage 8 mm
Switching Frequency 300 kHz
MTBF MIL-HDBK-217 F @ 25°C 650 k hours
Safety Standard IEC / EN / UL 62368-1 DK-133116-UL, E252573
Insulation System Reinforced Insulation
Environmental compliance RoHS

ENVIRONMENT SPECIFICATIONS
Parameter Conditions Min. Typ. Max. Unit
Operating Temperature See the Derating Curve -40 100 °C
Maximum Case Temperature 105 °C
Thermal Impedance 18 °C/W
Storage Humidity 95 % rel. H
Storage Temperature -55 125 °C
Cooling Natural Convection 30-65 LFM

Schmid Multitech GmbH Weinbergstraße 60b, 93105 Tegernheim - Germany www.schmid-m.com

The Copyright and authority for the interpretation of the products are reserved by SCHMID-M. Specifications subject to change without notice.
EMC SPECIFICATIONS
Parameter Standard Condition Criterion
Conducted Emissions EN55032 without external components A
Radiated Emissions EN55032 without external components A
ESD IEC 61000-4-2 Air ± 15kV, Contact ± 8kV A
RS IEC 61000-4-3 10V/m A
EFT IEC 61000-4-4 ±2kV with external components A
Surge IEC 61000-4-5 ±2kV with external components A
CS IEC 61000-4-6 10Vrms A
PFMF IEC 61000-4-8 100A/m A

PHYSICAL SPECIFICATIONS
Parameter Value

Case Material Non-conductive Black Plastic ( UL94V-0 rated )

Base Material Non-conductive Black Plastic ( UL94V-0 rated )
Pin Material Ø 0.5mm Brass Solder-coated
Potting Material Silicone ( UL94V-0 rated )
Weight 14.0 g, typ.
Dimensions 1.25" x 0.80" x 0.41"

Schmid Multitech GmbH Weinbergstraße 60b, 93105 Tegernheim - Germany www.schmid-m.com

The Copyright and authority for the interpretation of the products are reserved by SCHMID-M. Specifications subject to change without notice.
ELECTRICAL CHARACTERISTIC CURVES

SNC10HW-2405S、SNC10HW-2405D
SNC10HW-1205S、SNC10HW -1205D SNC10HW-4805S、SNC10HW-4805D

Derating Curve Derating Curve

120 120

OUTPUT POWER
OUTPUT POWER

100 100

75 75

50
S.O.A. 50
S.O.A.
25 25

0 0
-40 -20 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 120
72 74
AMBIENT TEMPERATURE(°C) AMBIENT TEMPERATURE(°C)

SNC10HW-1215S、SNC10HW-1215D、SNC10HW-2412S、SNC10HW-2412D
SNC10HW-1212S、SNC10HW-1212D SNC10HW-4812S、SNC10HW-4812D、SNC10HW-4815S、SNC10HW-4815D

Derating Curve Derating Curve

120 120
OUTPUT POWER
OUTPUT POWER

100 100

75 75

50
S.O.A. 50
S.O.A.
25 25

0 0
-40 -20 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 120
77
AMBIENT TEMPERATURE(°C) AMBIENT TEMPERATURE(°C)

SNC10HW-2415S、SNC10HW-2415D

Derating Curve
120
OUTPUT POWER

100

75

50
S.O.A.
25

0
-40 -20 0 20 40 60 80 100 120
82
AMBIENT TEMPERATURE(°C)

Schmid Multitech GmbH Weinbergstraße 60b, 93105 Tegernheim - Germany www.schmid-m.com

The Copyright and authority for the interpretation of the products are reserved by SCHMID-M. Specifications subject to change without notice.
TEST CONFIGURATIONS

Input Reflected Ripple Current Test Step

Input reflected ripple current is measured with a source inductor Lin(12μH) and a source capacitor
Cin(47μF, ESR<1.0Ω at 100KHz) at nominal input and full load.

+Vout
+Vin
Lin Current
Probe DC/DC Load
Cin Converter

-Vin -Vout

DESIGN & FEATURE CONFIGURATIONS

Over Current Protection

The module includes an internal over current protection circuit, which will endure current limiting for
an unlimited duration during output over load condition. If the output current exceeds the OCP set point,
the module will shut down automatically (hiccup).The module will try to restart after shut down. If the
over load condition still exists, the module will shut down again.

Over Voltage Protection

The module includes an internal output over voltage protection circuit, which monitors the voltage on
the output terminals. If this voltage exceeds the over voltage set point, the module will activate the
control loop of internal circuit to clamp the output voltage.

Remote Module ON / OFF

Negative logic turns on the module during low logic and off during high logic. For negative logic if the
Remote feature is not used, please leave the Remote pin floating or connected -Vin.

Schmid Multitech GmbH Weinbergstraße 60b, 93105 Tegernheim - Germany www.schmid-m.com

The Copyright and authority for the interpretation of the products are reserved by SCHMID-M. Specifications subject to change without notice.
 EMC Filter
The Circuit is used to meet Surge & EFT test.

Single

+Vin +Vout
DC/DC
Vin Load
C1 D1 Converter
-Vin -Vout

Dual

+Vin +Vout Load

DC/DC
Vin Com
C1 D1 Converter
-Vin -Vout Load

C1 D1

NIPPON chemi-con KY series Littelfuse

SNC10HW-12XXO
470μF, 100V SMDJ26A
NIPPON chemi-con KY series Littelfuse
SNC10HW-24XXO
330μF, 100V SMDJ58A
NIPPON chemi-con KY series Littelfuse
SNC10HW-48XXO
330μF, 100V SMDJ120A

Schmid Multitech GmbH Weinbergstraße 60b, 93105 Tegernheim - Germany www.schmid-m.com

The Copyright and authority for the interpretation of the products are reserved by SCHMID-M. Specifications subject to change without notice.
MECHANICAL SPECIFICATIONS

PIN CONNECTIONS
PIN
SINGLE DUAL
31.8 2.54 2.54 NUMBER
(1.25) (0.10) (0.10)
1 CTRL CTRL
1.93 20.32 4.47
DC-DC CONVERTER (0.08) (0.18)
SNC10HW-1205S
(0.80) 2 -Vin -Vin
Input：4.5-18Vdc 2878mA
20.3 2.53
Output：5Vdc 2000mA
(0.80)
SCHMID-M (0.10) 10 Trim Trim
1 2 10 11
2209
15.24
(0.60) 11 N.C. -Vout
Top view 23 22 16 14
2.53
(0.10)
14 +Vout +Vout
15.24
10.2
4.47
(0.60)
4.47 16 -Vout COM
(0.18) (0.18)
(0.41)
3.0
2.54 5.08
22 +Vin +Vin
(0.12)
(0.10) (0.20)

Side view Bottom view 23 +Vin +Vin

PIN CONNECTIONS
Output can be externally trimmed by using the
method as below.
Rtrim-up Rtrim-down
10 10

16 14

Single Output Models

Notes：All dimensions are typical in millimeters ( inches ).
Rtrim-up Rtrim-down
1. Pin diameter: 0.5±0.05 ( 0.02±0.002 ) 10 10
2. Pin pitch and length tolerance: ±0.35 ( ±0.014 )
3. Case tolerance: ±0.5 ( ±0.02 ) 11 14

Dual Output Models

RECOMMEND FOOTPRINT DETAILS

2.54 5.08
(0.10) (0.20)

4.77 15.24 4.77

(0.19) (0.60) (0.19)

2.83
(0.11)
Notes：1. All dimensions are typical in millimeters (inches).
23 22 16 14 Through hole(Black) 2, 3, 10, 11, 14, 16, 22, 23 : Ø 0.90 (0.035)
15.24 Top view pad(Green) 2, 3, 10, 11, 14, 16, 22, 23 : Ø 1.10 (0.044)
(0.60) Bottom view pad(Pink) 2, 3, 10, 11, 14, 16, 22, 23 : Ø 1.80 (0.071)
1 2 10 11 2. There should be at least 8mm distance between primary and secondary circuit.
2.83
(0.11)

2.23 20.32 4.77

(0.09) (0.80) (0.19)

2.54 2.54
(0.10) (0.10)
Top view

Schmid Multitech GmbH Weinbergstraße 60b, 93105 Tegernheim - Germany www.schmid-m.com

The Copyright and authority for the interpretation of the products are reserved by SCHMID-M. Specifications subject to change without notice.