https://www.quisure.

com

TL-702-Single Tower Lanp 70mm Siemens APT

Selection principles for tower lamp

Based on the usage and working environment, etc., the tower lamps shall be selected according to the following factors:
● Surrounding brightness
● Distance from the observation point
● Service life and use cost of the light source

m
● Noise level and pollution level of the service environment; if there are violent vibrations or shocks
● Influence on the safety caused by the emergent problems, such as light source damage
● Convenience in usage and maintenance
Therefore, different products are selected based on the operating requirements and the environmental characteristics, while the

co
maintenance convenience and economy shall be considered in any case.

Light source
1. Lamp bulb
The lamp bulb glows by heating the resistance wire during current flows.

.
The helical tungsten filament is normally used and the inert gas is injected into the bulb.

re
In general, the lamp bulb is featured by:
(1) If the voltage is 10% lower than the rated voltage of the lamp bulb, the service life can be increased by four times, the
consumption power reduces to 85% and the brightness drops to around 30%.
(2) If the voltage is 10% higher than the rated voltage, the service life can be shortened by 30%, the consumption power increases
around 16% and the brightness rises around 40%. Normally, the standard service life of the lamp bulb is 1,000 – 1,500 hours.
su
2. LED
Light-emitting diode (LED) is a solid light-emitting device by use of the semi-conductor electroluminescent effect, mainly made of
semi-conductor materials such as GaAs and GaP.
Like the normal semi-conductors, the service life of LED is affected by various factors such as overvoltage and surrounding
temperature, etc. However, unlike the lamp bulb whose filament will be thinner caused by volatilization and which will be subject to
ui

mechanical wear, it is shock and vibration resistance and longer service life without special aseismic structure. Furthermore, LED
has higher photoelectric conversion efficiency, which shall be deemed as an energy-saving clean light source with longer service
life.
Normally, the standard service life of LED is 100,000 hours.
.q

3. Xenon lamp
The xenon lamp glows by the gas excited by instantaneous high-energy, with higher brightness.
Compared with the common lamp bulb, xenon lamp requires bringing in extremely high electric energy instantly and letting out
enormous light intensity. As the low voltage for exciting xenon and the available accessory materials, Xe gas is used by this light
source, hence the name.
w

The bulb of xenon lamp can be fixed by seismic restraint method, with good seismic resistance. The spectrum of xenon lamp is
similar to that of natural light. Its working mode is explosion flashing, which is same with the camera’s flash lamp. Therefore, it has
extremely strong visuality.
w

Human perceptive volume

Human perceptive volume is different from the physical intensity of sound pressure (dB).
Under the same sound intensity (dB), if the tone (audio frequency, amplitude) is different, the perceptive volume is different.
w

Generally, the higher the audio frequency is, the more fidget people will get. Therefore, the stronger the sound intensity (dB) is and
the higher the tone (vibration and frequency) is, the louder the sound will be. That is, the higher the sound wave frequency is and
the larger the amplitude is, the louder the human perceptive volume will be.
The company also provides the products with sound intensity of 115dB. The warning tone with higher frequency is louder, and
vice versa.

1
TL-702 Single Signal Tower Lamp 70mm Siemens APT

TL-702 Acousto-optical single tower lamp

m
co
Performance features
● Acousto-optical combination
● Glowing forms include permanent, flashing, rotating
● The lampshade is made of panlite which is heat-resisting and anti-knock

.
Product Specifications

re
Appearance Model Specification Rated voltage/current Color

TL-702L permanent
su
TL-702F Flashing
Red
Yellow
TL-702S rotating
Green
ui

Blue
permanent, intermittent White
TL-702LI(C)
(continuous) sound
.q

TL-702FI(C) flashing, intermittent

(continuous) sound

TL-702SI(C) rotating, intermittent

w

(continuous) sound

Note: 24V and 110V are available for AC and DC; while 220V is only available for AC.
w

Model

Product height no marks: 137mm H1: 157mm H2: 187mm

w

Voltage class 23: AC/DC 24V

26: AC/DC 110V
31: AC 220V
Color red: r green: g yellow: y blue: b white: w
Sound forms No marks: silent I: intermittent C: continuous Three heights are available.
Glowing forms L: permanent F: flashing S: rotating Please specify when ordering

2
Side mounted base TL-CZ-1
Appearance Appearance Dimension

m
co
For side installation

.
re
su
ui
.q
w
w
w