THE MOBILE LINE

by
LIFT SYSTEMS, INC.

Global Leaders in Specialized

Lifting Equipment!
 MOBILE
MODEL CAPACITY PAGES
EQUIPMENT

WALK BEHIND CRANE

7.5 Ton 1-5
(WBC15)

MOBILIFT MBL033 33 Ton 7-14

MOBILIFT MBL075 75 TON 15-22

MOBILIFT MBL110 110 Ton 23-31

TWINLIFT TWL040 40 Ton 33-39

TWINLIFT TWL075 75 Ton 41-47

TWINLIFT TWL110 110 Ton 49-56

TF45/60 30 Ton 57-66

OTHER

STANDARD ON ALL
CARL CONTROL SYSTEM MOBILE EQUIPMENT 68-69
EXCEPT FOR WBC15

RECERTIFICATION PROGRAM 70
 7.5 Ton WALK BEHIND CRANE
by
LIFT SYSTEMS, INC.

Global Leaders in Specialized

Lifting Equipment!
1
 WALK BEHIND CRANE
7.5 TON

STANDARD EQUIPMENT
ENGINE: BOOM TELESCOPE CYLINDER:
Kubota, 3 cylinder, 17 hp, water cooled, propane Single cylinder capable of telescoping the boom
engine in and out with a full load. Integral safety
PUMP: holding valve.
Gear Pump rated at 7.56 GPM @ 2,000 PSI WINCH:
CONTROLS: High performance hydraulic winch. Integral, full
Separate controls for each function. load brake. 110’ of 7/16” wire rope standard.
Hydraulic lever controls allow for multiple functions BLOCK:
to be performed at the same time. 10 ton single sheave block standard.
DRIVE: Low profile with swivel hook.
Full hydrostatic drive system powers all wheels. POWER BOOM AND MAIN BOOM
WHEELS: LIFTING EYES:
Front: qty. (4) Qty. (1) located on power boom and qty. (1)
Diameter: 10” located on main boom each with 3 ton capacity.
Width: 5” WEIGHT:
Rear: qty. (2) 16,346 lbs base unit + counterweights
Diameter: 10” 11,622 lbs without counterweights
Width: 5” TIE DOWN EYES:
Replaceable polyurethane composition Tie down eyes installed for securing unit during
STEERING: transport of the unit.
90 degree steering with electric over hydraulic, ANTI-TWO-BLOCK DEVICE:
push button control. Safety device installed to prevent hook block
FLOOR LOADING: from contacting boom.
788 PSI with maximum load. OTHER STANDARD FEATURES:
HYDRAULIC RESERVOIR: Travel alarm, horn, and strobe light.
15 gallons
BOOM ROTATION:
220 degree slewing capability. Outriggers must be OPTIONAL EQUIPMENT
in the out and down position when slewing.
Boom is locked from rotation when outriggers are RADIO REMOTE CONTROL:
not extended. Radio remote control allows full machine
BOOM ANGLE RANGE: functionality from a wireless radio remote.
-5 degrees to +74 degrees Allows operator optimal view of load.
BOOM LIFT CYLINDERS: Emergency safety shutdown switch is standard.
Dual cylinders capable of lifting and lowering with a JIB EXTENSION:
full load. Integral safety holding valve. Consult factory for available capacities and
lengths.

2
WALK BEHIND CRANE
7.5 TON

DIMENSIONAL DATA

3
 WALK BEHIND CRANE
7.5 TON

RANGE DIAGRAM

NOTE
1. The above chart is for reference purposes only.
2. Never use the above chart for lift planning calculations
3. Lift plan calculations are to be determined solely by the load charts and range diagrams that are issued for
the specific serial numbered machine that is to be used for the specific planned lift.

4
 WALK BEHIND CRANE
7.5 TON

LOAD CHARTS FOR BASE UNIT WITH FULL COUNTERWEIGHT

NOTE:
Specifications are provided in imperial dimensions. All equipment dimensions, designs, specifications, calculations, etc., as described, are subject to change at manufacturer’s
discretion at any time and without notice. Weights are approximate and may vary. Data herein is for informational purposes only and will not be construed to guarantee
suitability of equipment for any particular as performance my vary with conditions encountered. Warranty will apply as written in standard contract form upon purchase of
equipment. Capacities are for reference only and must not be used for any serial numbered machine. Serial numbered load charts may be obtained from Lift Systems, Inc.

LIFT SYSTEMS, INC. TEL: +1-309-764-9842

OFFICE: MAILING ADDRESS: FAX: +1-309-764-9848
1505 - 7th Street P.O. Box 906 EMAIL: [email protected]
East Moline, IL 61244 Moline, IL 61266 WEB: www.lift-systems.com

5
THIS PAGE INTENTIONALLY LEFT BLANK

6
 33 TON MOBILIFT
by
LIFT SYSTEMS, INC.

Global Leaders in Specialized

Lifting Equipment!
7
 MOBILIFT
33 TON

STANDARD EQUIPMENT
ENGINE: BOOM TELESCOPE CYLINDER:
GM 3.0L, 4 cylinder, 75 hp (56 Kw) propane engine Single cylinder capable of telescoping the boom in and
PUMP: out with a full load. Integral safety holding valve.
Sundstrand 40 series drive pump WINCH:
CONTROL SYSTEM: High performance hydraulic winch. Integral, full load
CARL (Computer Assisted Remote Lifting) Control System. brake. 400’ of high capacity 5/8” wire rope standard.
Monitors Boom Angle, Boom Extension, Pressure, BLOCK:
Counterweight Load Pin. Automatic Shutdown for overload 35 (31.5) ton block standard. Low profile with swivel
conditions. Large easy to read display screen with push hook.
button navigation and dial adjustment. POWER BOOM LIFTING EYE:
CONTROLS: Qty. (1) located on boom with
Separate controls for each function. 33 ton capacity.
Combination of foot pedal, joystick, and push WEIGHT:
button controls allows for multiple functions to be 32,000 lbs base unit
performed at the same time. Standard “A” counterweight included
DRIVE: COUNTERWEIGHTS:
Rockwell planetary drive axle. Full hydrostatic system with “A” - non-removable counterweight installed in unit
spring applied brakes. Four (4) additional counterweight plates included with
WHEELS: fork lift loops standard. Weight of each plate is 5,500 lbs.
Front: qty. (4) Total of additional counterweight is 22,000 lbs.
Diameter: 28” TIE DOWN / LIFTING EYES:
Width: 12” Tie down / lifting eyes installed for securing unit during
Rear: qty. (2) transport and for lifting of the unit.
Diameter: 28” DRIVER PROTECTION GUARD:
Width: 12” Structural overhead guard for operator protection.
Replaceable polyurethane composition
OTHER STANDARD FEATURES:
OSCILLATING REAR STEERING BOX: Back up alarm, horn, strobe light, operator seat
Keeps all steering wheels in contact with ground. complete with safety belt and electric switch.
GRADABILITY:
Unloaded maximum grade is 26%
Loaded maximum grade is 15%
18,000 lbs of draw bar pull unloaded
TRAVEL SPEED UNLOADED:
High Gear: 2.75 mph
Low Gear: 0.75 mph
OPTIONAL EQUIPMENT
TELESCOPING COUNTERWEIGHT: RADIO REMOTE CONTROL:
Standard counterweight section telescopes 4’ Radio remote control allows full machine functionality
using a hydraulic cylinder. Push button control. from a wireless radio remote. Allows operator optimal
HYDRAULIC RESERVOIR: view of load. Emergency safety shutdown switch is
90 gallons (340 liters) standard.
BOOM: ANTI-TWO-BLOCK DEVICE:
High strength three section telescoping boom with powered Safety device installed to prevent hook block from
first section and manually extended second section . contacting boom.
Replaceable wear pads on all sliding sections. JIB EXTENSION:
BOOM LIFT CYLINDER: Consult factory for available capacities
Single cylinder capable of lifting and lowering with a full load.
Integral safety holding valve. Spherical bearing ensures
constant alignment with the boom.

8
 MOBILIFT
33 TON

DIMENSIONAL DATA

9
 MOBILIFT
33 TON

REFERENCE CAPACITY / RANGE DIAGRAM

NOTE
1. The above chart is for reference purposes only.
2. Never use the above chart for lift planning calculations
3. Lift plan calculations are to be determined solely by the load charts and range diagrams that are issued for
the specific serial numbered machine that is to be used for the specific planned lift.

10
 MOBILIFT
33 TON

RANGE DIAGRAM

NOTE
1. The above chart is for reference purposes only.
2. Never use the above chart for lift planning calculations
3. Lift plan calculations are to be determined solely by the load charts and range diagrams that are issued for
the specific serial numbered machine that is to be used for the specific planned lift.

11
 MOBILIFT
33 TON
LOAD CHARTS FOR BASE UNIT WITH NO COUNTERWEIGHT

LOAD CHARTS FOR BASE UNIT WITH 1 COUNTERWEIGHT SLAB

NOTE:
Specifications are provided in metric dimensions. All equipment dimensions, designs, specifications, calculations, etc., as described, are
subject to change at manufacturer’s discretion at any time and without notice. Weights are approximate and may vary. Data herein is for informational purposes only and will
not be construed to guarantee suitability of equipment for any particular as performance my vary with conditions encountered. Warranty will apply as written in standard con-
tract form upon purchase of equipment. Capacities are for reference only and must not be used for any serial numbered machine. Serial numbered load charts may be obtained
from Lift Systems, Inc.

12
 MOBILIFT
33 TON
LOAD CHARTS FOR BASE UNIT WITH 2 COUNTERWEIGHT SLABS

LOAD CHARTS FOR BASE UNIT WITH 3 COUNTERWEIGHT SLABS

NOTE:
Specifications are provided in metric dimensions. All equipment dimensions, designs, specifications, calculations, etc., as described, are
subject to change at manufacturer’s discretion at any time and without notice. Weights are approximate and may vary. Data herein is for informational purposes only and will
not be construed to guarantee suitability of equipment for any particular as performance my vary with conditions encountered. Warranty will apply as written in standard con-
tract form upon purchase of equipment. Capacities are for reference only and must not be used for any serial numbered machine. Serial numbered load charts may be obtained
from Lift Systems, Inc.

13
 MOBILIFT
33 TON
LOAD CHARTS FOR BASE UNIT WITH FULL COUNTERWEIGHT (4 SLABS)

LOAD CHARTS FOR POWER BOOM PICKING EYE + FULL COUNTERWEIGHT (4 SLABS)

LIFT SYSTEMS, INC. TEL: +1-309-764-9842

OFFICE: MAILING ADDRESS: FAX: +1-309-764-9848
1505 - 7th Street P.O. Box 906 EMAIL: [email protected]
East Moline, IL 61244 Moline, IL 61266 WEB: www.lift-systems.com

14
 75 TON MOBILFT
by
LIFT SYSTEMS, INC.

Global Leaders in Specialized

Lifting Equipment!
15
 MOBILIFT
75 TON

STANDARD EQUIPMENT
ENGINE: BOOM:
Cummins Diesel Engine: QSB3.3P High strength three section telescoping boom with powered
108 hp (81 Kw) intermittent @ 2200 rpm first section and manually extended second section.
U.S. EPA Tier 3 Replaceable wear pads on all sliding sections.
CARB Tier 3 BOOM LIFT CYLINDERS:
EU Stage III Twin cylinders capable of lifting and lowering with a full
Torque @ 1600 rpm, 306 ft-lbs (415 N-m) load. Safety holding valves installed on both cylinders.
PUMP: Spherical bearings ensure constant alignment with the
Sundstrand 90 series drive pump boom.
CONTROL SYSTEM: BOOM TELESCOPE CYLINDER:
CARL (Computer Assisted Remote Lifting) Control System. Single cylinder capable of telescoping the boom in and out
Monitors Boom Angle, Boom Extension, Pressure, with a full load. Safety holding valve is installed on the
Counterweight Load Pin. Automatic Shutdown for overload cylinder.
conditions. Large easy to read display screen with push LIFTING EYES:
button navigation and dial adjustment. Qty. one (1) centrally located on main boom and one (1)
CONTROLS: located on power boom both with 75 ton capacity.
Separate controls for each function. WINCH:
Combination of foot pedal, joystick, and push Two speed high performance hydraulic winch. Integral, full
button controls allows for multiple functions to be capacity load brake. Wide, low profile drum. 580’ - 5/8”
performed at the same time. wire rope capacity.
DRIVE: WEIGHT:
Poclain MK35 drive motors (qty. 3) 48,000 lbs.
(2) in front, (1) in rear steering box. Standard “A” counterweight included
WHEELS: COUNTERWEIGHTS:
Front: qty. (4) “A” - non-removable counterweight installed in unit
Diameter: 28” “B” - qty. (2) - 7,300 lbs each. - 14,600 lbs total
Width: (2) @ 16” and (2) @ 10” “C” - qty. (1) - 8,450 lbs
Rear: qty. (2) “D” - qty. (1) - 8,050 lbs
Diameter: 28” TIE DOWN / LIFTING EYES:
Width: 16” Tie down / lifting eyes installed for securing unit during
Replaceable polyurethane composition transport and for lifting of the unit.
STEERING: DRIVER PROTECTION GUARD:
90 degree steering of rear wheels. Structural overhead guard for operator protection.
OSCILLATING REAR STEERING BOX: OTHER STANDARD FEATURES:
Keeps all steering wheels in contact with ground. Back up alarm, horn, strobe light, operator seat
GRADABILITY: complete with safety belt and electric switch.
Unloaded maximum grade is 20%
Loaded maximum grade is 10%
GROUND BEARING PRESSURE:
OPTIONAL EQUIPMENT
Loaded Front Tires: 360 psi maximum RADIO REMOTE CONTROL:
Unloaded Rear Tires: 440 psi maximum Radio remote control allows full machine functionality from
TRAVEL SPEED UNLOADED: a wireless radio remote. Allows operator optimal view of
Travel Mode - High Gear = 0.0 to 1.70 mph load. Emergency safety shutdown switch is standard.
Travel Mode - Low Gear = 0.0 to 0.86 mph 65 TON SPINNER:
Work Mode - Low Gear = 0.0 to 0.42 mph Allows for 360 degree rotation of load from picking eye.
TELESCOPING COUNTERWEIGHT: EXHAUST PURFIER:
Standard counterweight section telescopes 5’ Reduces diesel particulate matter.
using (2) hydraulic cylinders. Push button control. JIB EXTENSION:
HYDRAULIC RESERVOIR: Consult factory for available capacities
200 gallons (757 liters)

16
 MOBILIFT
75 TON

DIMENSIONAL DATA

17
 MOBILIFT
75 TON

REFERENCE CAPACITY / RANGE DIAGRAM

NOTE
1. The above chart is for reference purposes only.
2. Never use the above chart for lift planning calculations
3. Lift plan calculations are to be determined solely by the load charts and range diagrams that are issued for
the specific serial numbered machine that is to be used for the specific planned lift.

18
 MOBILIFT
75 TON

RANGE DIAGRAM

NOTE
1. The above chart is for reference purposes only.
2. Never use the above chart for lift planning calculations
3. Lift plan calculations are to be determined solely by the load charts and range diagrams that are issued for
the specific serial numbered machine that is to be used for the specific planned lift.

19
 MOBILIFT
75 TON
LOAD CHARTS FOR “A” COUNTERWEIGHT (HOOK BLOCK)

LOAD CHARTS FOR “A” AND “B” COUNTERWEIGHT (HOOK BLOCK)

NOTE:
Specifications are provided in imperial dimensions. All equipment dimensions, designs, specifications, calculations, etc., as described, are subject to change at manufacturer’s
discretion at any time and without notice. Weights are approximate and may vary. Data herein is for informational purposes only and will not be construed to guarantee
suitability of equipment for any particular as performance my vary with conditions encountered. Warranty will apply as written in standard contract form upon purchase of
equipment. Capacities are for reference only and must not be used for any serial numbered machine. Serial numbered load charts may be obtained from Lift Systems, Inc.

20
 MOBILIFT
75 TON
LOAD CHARTS
LOAD CHARTS FOR
FOR “A”, “A”
“B”, COUNTERWEIGHT
AND (HOOK (HOOK
“C” COUNTERWEIGHT BLOCK)BLOCK)

LOADCHARTS
LOAD CHARTS FOR
FOR “A”
“A”, AND
“B”, “C”,“B”
ANDCOUNTERWEIGHT (HOOK
“D” COUNTERWEIGHT (HOOKBLOCK)
BLOCK)

NOTE:
Specifications are provided in imperial dimensions. All equipment dimensions, designs, specifications, calculations, etc., as described, are subject to change at manufacturer’s
discretion at any time and without notice. Weights are approximate and may vary. Data herein is for informational purposes only and will not be construed to guarantee
suitability of equipment for any particular as performance my vary with conditions encountered. Warranty will apply as written in standard contract form upon purchase of
equipment. Capacities are for reference only and must not be used for any serial numbered machine. Serial numbered load charts may be obtained from Lift Systems, Inc.

21
 MOBILIFT
75 TON
POWER BOOM MAIN BOOM
LIFTING EYE LOAD CHARTS LIFTING EYE LOAD CHARTS

NOTE:
The power section boom must be fully
retracted.
The ratings above the bold line are based
upon machine's hydraulic or structural
strength and not stability.
Ratings below bold line are based on 85% of
tipping.
All capacities are in pounds.

CAUTION!
Do not extend or retract counterweight with any load suspended on hook.

LIFT SYSTEMS, INC. TEL: +1-309-764-9842

OFFICE: MAILING ADDRESS: FAX: +1-309-764-9848
1505 - 7th Street P.O. Box 906 EMAIL: [email protected]
East Moline, IL 61244 Moline, IL 61266 WEB: www.lift-systems.com

22
 110 TON MOBILIFT
by
LIFT SYSTEMS, INC.

Global Leaders in Specialized

Lifting Equipment!
23
 MOBILIFT
110 TON

STANDARD EQUIPMENT
ENGINE: BOOM:
Cummins Diesel Engine: QSB4.5P High strength three section telescoping boom with powered
160 hp (116 Kw) intermittent @ 2500 rpm first section and manually extended second section.
U.S. EPA Tier 3 Replaceable wear pads on all sliding sections.
CARB Tier 3 BOOM LIFT CYLINDERS:
EU Stage III Twin cylinders capable of lifting and lowering with a full
Torque @ 1500 rpm, 466 ft-lbs (632 N-m) load. Safety holding valves installed on both cylinders.
PUMP: Spherical bearings ensure constant alignment with the
Sundstrand 90 series drive pump boom.
CONTROL SYSTEM: BOOM TELESCOPE CYLINDER:
CARL (Computer Assisted Remote Lifting) Control System. Single cylinder capable of telescoping the boom in and out
Monitors Boom Angle, Boom Extension, Pressure, with a full load. Safety holding valve is installed on the
Counterweight Load Pin. Automatic Shutdown for overload cylinder.
conditions. Large easy to read display screen with push LIFTING EYES:
button navigation and dial adjustment. Qty. one (1) centrally located on main boom and one (1)
CONTROLS: located on power boom both with 110 ton capacity.
Separate controls for each function. WINCH:
Combination of foot pedal, joystick, and push Two speed high performance hydraulic winch. Integral, full
button controls allows for multiple functions to be capacity load brake. Wide, low profile drum. 500’ - 1” wire
performed at the same time. rope capacity.
DRIVE: WEIGHT:
Poclain MK35 drive motors (qty. 3) 58,200 lbs.
(2) in front, (1) in rear steering box. Standard “A” counterweight included
WHEELS: COUNTERWEIGHTS:
Front: qty. (4) “A” - non-removable counterweight installed in unit
Diameter: 28” “B” - qty. (2) - 8,270 lbs each. - 16,540 lbs total
Width: (2) @ 24” and (2) @ 16” “C” - qty. (1) - 9,200 lbs
Rear: qty. (2) “D” - qty. (1) - 9,200 lbs
Diameter: 28” “E” - qty. (1) - 9,200 lbs
Width: 16” TIE DOWN / LIFTING EYES:
Replaceable polyurethane composition Tie down / lifting eyes installed for securing unit during
STEERING: transport and for lifting of the unit.
90 degree steering of rear wheels. DRIVER PROTECTION GUARD:
OSCILLATING REAR STEERING BOX: Structural overhead guard for operator protection.
Keeps all steering wheels in contact with ground. OTHER STANDARD FEATURES:
GRADABILITY: Back up alarm, horn, strobe light, operator seat
Unloaded maximum grade is 20% complete with safety belt and electric switch.
Loaded maximum grade is 8%
GROUND BEARING PRESSURE:
Loaded Front Tires: 634 psi maximum
OPTIONAL EQUIPMENT
Unloaded Rear Tires: 502 psi maximum RADIO REMOTE CONTROL:
TRAVEL SPEED UNLOADED: Radio remote control allows full machine functionality from
Travel Mode - High Gear = 0.0 to 1.70 mph a wireless radio remote. Allows operator optimal view of
Travel Mode - Low Gear = 0.0 to 0.86 mph load. Emergency safety shutdown switch is standard.
Work Mode - Low Gear = 0.0 to 0.42 mph 110 TON SPINNER:
TELESCOPING COUNTERWEIGHT: Allows for 360 degree rotation of load from picking eye.
Standard counterweight section telescopes 5’ EXHAUST PURFIER:
using (2) hydraulic cylinders. Push button control. Reduces diesel particulate matter.
HYDRAULIC RESERVOIR: JIB EXTENSION:
200 gallons (757 liters) Consult factory for available capacities
24
 MOBILIFT
110 TON

DIMENSIONAL DATA

25
 MOBILIFT
110 TON

REFERENCE CAPACITY / RANGE DIAGRAM

NOTE
1. The above chart is for reference purposes only.
2. Never use the above chart for lift planning calculations
3. Lift plan calculations are to be determined solely by the load charts and range diagrams that are issued for
the specific serial numbered machine that is to be used for the specific planned lift.

26
 MOBILIFT
110 TON

RANGE DIAGRAM

NOTE
1. The above chart is for reference purposes only.
2. Never use the above chart for lift planning calculations
3. Lift plan calculations are to be determined solely by the load charts and range diagrams that are issued for
the specific serial numbered machine that is to be used for the specific planned lift.

27
 MOBILIFT
110 TON
LOAD CHARTS FOR “A” COUNTERWEIGHT (HOOK BLOCK)

LOAD CHARTS FOR “A” AND “B” COUNTERWEIGHT (HOOK BLOCK)

NOTE:
Specifications are provided in imperial dimensions. All equipment dimensions, designs, specifications, calculations, etc., as described, are subject to change at manufacturer’s
discretion at any time and without notice. Weights are approximate and may vary. Data herein is for informational purposes only and will not be construed to guarantee
suitability of equipment for any particular as performance my vary with conditions encountered. Warranty will apply as written in standard contract form upon purchase of
equipment. Capacities are for reference only and must not be used for any serial numbered machine. Serial numbered load charts may be obtained from Lift Systems, Inc.

28
 MOBILIFT
110 TON
LOAD CHARTS
LOAD CHARTS FOR
FOR “A”, “A”
“B”, COUNTERWEIGHT
AND (HOOK (HOOK
“C” COUNTERWEIGHT BLOCK)BLOCK)

LOADCHARTS
LOAD CHARTS FOR
FOR “A”
“A”, AND
“B”, “C”,“B”
ANDCOUNTERWEIGHT (HOOK
“D” COUNTERWEIGHT (HOOKBLOCK)
BLOCK)

NOTE:
Specifications are provided in imperial dimensions. All equipment dimensions, designs, specifications, calculations, etc., as described, are subject to change at manufacturer’s
discretion at any time and without notice. Weights are approximate and may vary. Data herein is for informational purposes only and will not be construed to guarantee
suitability of equipment for any particular as performance my vary with conditions encountered. Warranty will apply as written in standard contract form upon purchase of
equipment. Capacities are for reference only and must not be used for any serial numbered machine. Serial numbered load charts may be obtained from Lift Systems, Inc.

29
 MOBILIFT
110 TON

LOAD CHARTS FOR “A”, “B”, “C”, “D”, and “E” COUNTERWEIGHT (HOOK BLOCK)

NOTE:
Specifications are provided in imperial dimensions. All equipment dimensions, designs, specifications, calculations, etc., as described, are subject to change at manufacturer’s
discretion at any time and without notice. Weights are approximate and may vary. Data herein is for informational purposes only and will not be construed to guarantee
suitability of equipment for any particular as performance my vary with conditions encountered. Warranty will apply as written in standard contract form upon purchase of
equipment. Capacities are for reference only and must not be used for any serial numbered machine. Serial numbered load charts may be obtained from Lift Systems, Inc.

30
 MOBILIFT
110 TON

POWER BOOM LIFTING EYE

LOAD CHARTS WITH FULL COUNTERWEIGHT (A,B,C,D,E WEIGHTS)

NOTE:
The ratings above the bold line are based upon machine's hydraulic or structural
strength and not stability.
Ratings below bold line are based on 85% of tipping.
All capacities are in pounds.

CAUTION!
Do not extend or retract counterweight with any load suspended on hook.

LIFT SYSTEMS, INC. TEL: +1-309-764-9842

OFFICE: MAILING ADDRESS: FAX: +1-309-764-9848
1505 - 7th Street P.O. Box 906 EMAIL: [email protected]
East Moline, IL 61244 Moline, IL 61266 WEB: www.lift-systems.com

31
THIS PAGE INTENTIONALLY LEFT BLANK

32
 40 TON TWINLIFT
by
LIFT SYSTEMS, INC.

Global Leaders in Specialized

Lifting Equipment!
33
 TWINLIFT
40 TON

STANDARD EQUIPMENT

ENGINE: BOOM LIFT CYLINDERS:

GM Industrial 4.3L Propane Engine Twin cylinders capable of lifting and lowering with a full
105HP load. Safety holding valves installed on both cylinders.
U.S. EPA Tier 3 Spherical bearings ensure constant alignment with the
CARB Tier 3 boom.
EU Stage III BOOM TELESCOPE CYLINDERS:
CONTROL SYSTEM: Twin cylinders capable of telescoping the boom in and
CARL (Computer Assisted Remote Lifting) Control System. out with a full load. Safety holding valves are installed on
Monitors Boom Angle, Boom Extension, Counterweight both cylinders.
Extension, Pressure, Counterweight Load Pin. Automatic LIFTING EYES:
Shutdown for overload conditions. Large easy to read display Qty. (1) centrally located on boom with
screen with push button navigation and dial adjustment. 40 ton capacity
CONTROLS: Qty. (2) located on corners of boom with
Separate controls for each function. 20 ton capacity each
Combination of foot pedal, joystick, and push WINCH MOUNT:
button controls allows for multiple functions to be Standard mount for optional winch
performed at the same time. WEIGHT:
DRIVE: 36,000 lbs.
Brevini drive motors (qty. 3) Standard “A” counterweight included
(2) in front, (1) in rear steering box. COUNTERWEIGHTS:
WHEELS: “A” - non-removable counterweight installed in unit
Front: qty. (4) “B” - qty. (2) - 4,850 lbs each. - 9,700 lbs total
Diameter: 28” “C” - qty. (1) - 8,500 lbs
Width: 10” TIE DOWN / LIFTING EYES:
Rear: qty. (2) Tie down / lifting eyes installed for securing unit during
Diameter: 28” transport and for lifting of the unit.
Width: 10”
Replaceable polyurethane composition DRIVER PROTECTION GUARD:
Structural overhead guard for operator protection.
STEERING:
90 degree steering of rear wheels. OTHER STANDARD FEATURES:
Back up alarm, horn, strobe light, operator seat
OSCILLATING REAR STEERING BOX: complete with safety belt and electric switch.
Keeps all steering wheels in contact with ground.
GRADABILITY:
Unloaded maximum grade is 17%
OPTIONAL EQUIPMENT
Loaded maximum grade is 3.5% RADIO REMOTE CONTROL:
GROUND BEARING PRESSURE: Radio remote control allows full machine functionality
Loaded Front Tires: 780 psi maximum from a wireless radio remote. Allows operator optimal
Unloaded Rear Tires: 660 psi maximum view of load. Emergency safety shutdown switch is
TELESCOPING COUNTERWEIGHT: standard.
Standard counterweight section telescopes 5’ HYDRAULIC WINCH:
using (2) hydraulic cylinders. Push button control. Consult factory for available capacities
HYDRAULIC RESERVOIR: FORKLIFT ATTACHMENT:
100 gallons (378 liters) Consult factory for available capacities
JIB EXTENSION:
Consult factory for available capacities

34
 TWINLIFT
40 TON

DIMENSIONAL DATA

35
 TWINLIFT
40 TON

REFERENCE CAPACITY / RANGE DIAGRAM

NOTE
1. The above chart is for reference purposes only.
2. Never use the above chart for lift planning calculations
3. Lift plan calculations are to be determined solely by the load charts and range diagrams that are issued for
the specific serial numbered machine that is to be used for the specific planned lift.

36
 TWINLIFT
40 TON

RANGE DIAGRAM

NOTE
1. The above chart is for reference purposes only.
2. Never use the above chart for lift planning calculations
3. Lift plan calculations are to be determined solely by the load charts and range diagrams that are issued for
the specific serial numbered machine that is to be used for the specific planned lift.

37
 TWINLIFT
40 TON
LOAD CHARTS FOR “A” COUNTERWEIGHT

LOAD CHARTS FOR “A” AND “B” COUNTERWEIGHT

NOTE:
Specifications are provided in imperial dimensions. All equipment dimensions, designs, specifications, calculations, etc., as described, are subject to change at manufacturer’s
discretion at any time and without notice. Weights are approximate and may vary. Data herein is for informational purposes only and will not be construed to guarantee
suitability of equipment for any particular as performance my vary with conditions encountered. Warranty will apply as written in standard contract form upon purchase of
equipment. Capacities are for reference only and must not be used for any serial numbered machine. Serial numbered load charts may be obtained from Lift Systems, Inc.

38
 TWINLIFT
40 TON

LOAD CHARTS FOR “A”, “B”, AND “C” COUNTERWEIGHT

NOTE:
Specifications are provided in imperial dimensions. All equipment dimensions, designs, specifications, calculations, etc., as described, are subject to change at manufacturer’s
discretion at any time and without notice. Weights are approximate and may vary. Data herein is for informational purposes only and will not be construed to guarantee
suitability of equipment for any particular as performance my vary with conditions encountered. Warranty will apply as written in standard contract form upon purchase of
equipment. Capacities are for reference only and must not be used for any serial numbered machine. Serial numbered load charts may be obtained from Lift Systems, Inc.

LIFT SYSTEMS, INC. TEL: +1-309-764-9842

OFFICE: MAILING ADDRESS: FAX: +1-309-764-9848
1505 - 7th Street P.O. Box 906 EMAIL: [email protected]
East Moline, IL 61244 Moline, IL 61266 WEB: www.lift-systems.com

39
THIS PAGE INTENTIONALLY LEFT BLANK

40
 75 TON TWINLIFT
by
LIFT SYSTEMS, INC.

Global Leaders in Specialized

Lifting Equipment!
41
 TWINLIFT
75 TON

STANDARD EQUIPMENT
ENGINE: BOOM LIFT CYLINDERS:
Cummins Diesel Engine: QSB3.3P Twin cylinders capable of lifting and lowering with a full
108 hp (81 Kw) intermittent @ 2200 rpm load. Safety holding valves installed on both cylinders.
U.S. EPA Tier 3 Spherical bearings ensure constant alignment with the
CARB Tier 3 boom.
EU Stage III BOOM TELESCOPE CYLINDERS:
Torque @ 1600 rpm, 306 ft-lbs (415 N-m) Twin cylinders capable of telescoping the boom in and
PUMP: out with a full load. Safety holding valves are installed on
Sundstrand 90 series drive pump both cylinders.
CONTROL SYSTEM: LIFTING EYES:
CARL (Computer Assisted Remote Lifting) Control System. Qty. (1) centrally located on boom with
Monitors Boom Angle, Boom Extension, Pressure, 75 ton capacity
Counterweight Load Pin. Automatic Shutdown for overload Qty. (2) located on corners of boom with
conditions. Large easy to read display screen with push 37.5 ton capacity each
button navigation and dial adjustment. WINCH MOUNT:
CONTROLS: Standard mount for optional winch
Separate controls for each function. WEIGHT:
Combination of foot pedal, joystick, and push 48,000 lbs.
button controls allows for multiple functions to be Standard “A” counterweight included
performed at the same time. COUNTERWEIGHTS:
DRIVE: “A” - non-removable counterweight installed in unit
Poclain MK35 drive motors (qty. 3) “B” - qty. (2) - 7,300 lbs each. - 14,600 lbs total
(2) in front, (1) in rear steering box. “C” - qty. (1) - 8,450 lbs
WHEELS: “D” - qty. (1) - 8,050 lbs
Front: qty. (4) TIE DOWN / LIFTING EYES:
Diameter: 28” Tie down / lifting eyes installed for securing unit during
Width: (2) @ 16” and (2) @ 10” transport and for lifting of the unit.
Rear: qty. (2) DRIVER PROTECTION GUARD:
Diameter: 28” Structural overhead guard for operator protection.
Width: 16”
Replaceable polyurethane composition OTHER STANDARD FEATURES:
Back up alarm, horn, strobe light, operator seat
STEERING: complete with safety belt and electric switch.
90 degree steering of rear wheels.
OSCILLATING REAR STEERING BOX:
Keeps all steering wheels in contact with ground.
OPTIONAL EQUIPMENT
GRADABILITY: RADIO REMOTE CONTROL:
Unloaded maximum grade is 20% Radio remote control allows full machine functionality
Loaded maximum grade is 10% from a wireless radio remote. Allows operator optimal
GROUND BEARING PRESSURE: view of load. Emergency safety shutdown switch is
Loaded Front Tires: 360 psi maximum standard.
Unloaded Rear Tires: 440 psi maximum 65 TON SPINNER:
TRAVEL SPEED UNLOADED: Allows for 360 degree rotation of load
Travel Mode - High Gear = 0.0 to 1.70 mph HYDRAULIC WINCH:
Travel Mode - Low Gear = 0.0 to 0.86 mph Consult factory for available capacities
Work Mode - Low Gear = 0.0 to 0.42 mph FORKLIFT ATTACHMENT:
TELESCOPING COUNTERWEIGHT: Consult factory for available capacities
Standard counterweight section telescopes 5’ JIB EXTENSION:
using (2) hydraulic cylinders. Push button control. Consult factory for available capacities
HYDRAULIC RESERVOIR:
140 gallons (530 liters)

42
 TWINLIFT
75 TON

DIMENSIONAL DATA

43
 TWINLIFT
75 TON

REFERENCE CAPACITY / RANGE DIAGRAM

NOTE
1. The above chart is for reference purposes only.
2. Never use the above chart for lift planning calculations
3. Lift plan calculations are to be determined solely by the load charts and range diagrams that are issued for
the specific serial numbered machine that is to be used for the specific planned lift.

44
 TWINLIFT
75 TON

RANGE DIAGRAM

NOTE
1. The above chart is for reference purposes only.
2. Never use the above chart for lift planning calculations
3. Lift plan calculations are to be determined solely by the load charts and range diagrams that are issued for
the specific serial numbered machine that is to be used for the specific planned lift.

45
 TWINLIFT
75 TON
LOAD CHARTS FOR “A” COUNTERWEIGHT

LOAD CHARTS FOR “A” AND “B” COUNTERWEIGHT

NOTE:
Specifications are provided in metric dimensions. All equipment dimensions, designs, specifications, calculations, etc., as described, are
subject to change at manufacturer’s discretion at any time and without notice. Weights are approximate and may vary. Data herein is for informational purposes only and will
not be construed to guarantee suitability of equipment for any particular as performance my vary with conditions encountered. Warranty will apply as written in standard con-
tract form upon purchase of equipment. Capacities are for reference only and must not be used for any serial numbered machine. Serial numbered load charts may be obtained
from Lift Systems, Inc.

46
 TWINLIFT
75 TON
LOAD CHARTS FOR “A”, “B”, AND “C” COUNTERWEIGHT

LOAD CHARTS FOR “A”, “B”, “C”, AND “D” COUNTERWEIGHT

LIFT SYSTEMS, INC. TEL: +1-309-764-9842

OFFICE: MAILING ADDRESS: FAX: +1-309-764-9848
1505 - 7th Street P.O. Box 906 EMAIL: [email protected]
East Moline, IL 61244 Moline, IL 61266 WEB: www.lift-systems.com

47
THIS PAGE INTENTIONALLY LEFT BLANK

48
 110 TON TWINLIFT
by
LIFT SYSTEMS, INC.

Global Leaders in Specialized

Lifting Equipment!
49
 TWINLIFT
110 TON

STANDARD EQUIPMENT
ENGINE: BOOM LIFT CYLINDERS:
Cummins Diesel Engine: QSB4.5P Twin cylinders capable of lifting and lowering with a full
160 hp (116 kW) intermittent @ 2500 rpm load. Safety holding valves installed on both cylinders.
U.S. EPA Tier 3 Spherical bearings ensure constant alignment with the
CARB Tier 3 boom.
EU Stage III BOOM TELESCOPE CYLINDERS:
Torque @ 1500 rpm, 466 ft-lbs (632 N-m) Twin cylinders capable of telescoping the boom in and
PUMP: out with a full load. Safety holding valves are installed on
Sundstrand 90 series drive pump both cylinders.
CONTROL SYSTEM: LIFTING EYES:
CARL (Computer Assisted Remote Lifting) Control System. Qty. (1) centrally located on boom with
Monitors Boom Angle, Boom Extension, Counterweight 110 ton capacity
Extension, Pressure, Counterweight Load Pin. Automatic Qty. (2) located on corners of boom with
Shutdown for overload conditions. Large easy to read display 55 ton capacity each
screen with push button navigation and dial adjustment. WINCH MOUNT:
CONTROLS: Standard mount for optional winch
Separate controls for each function. WEIGHT:
Combination of foot pedal, joystick, and push 58,200 lbs. (26,400 kg)
button controls allows for multiple functions to be Standard “A” counterweight included
performed at the same time. COUNTERWEIGHTS:
DRIVE: “A” - non-removable counterweight installed in unit
Poclain MK35 drive motors (qty. 3) “B” - qty. (2) - 8,270 each. - 16,540 lbs total
(2) in front, (1) in rear steering box. “C” - qty. (1) - 9,200 lbs
WHEELS: “D” - qty. (1) - 9,200 lbs
Front: qty. (4) “E” - qty. (1) - 9,200 lbs
Diameter: 28” TIE DOWN / LIFTING EYES:
Width: (2) @ 24” and (2) @ 16” Tie down / lifting eyes installed for securing unit during
Rear: qty. (2) transport and for lifting of the unit.
Diameter: 28” DRIVER PROTECTION GUARD:
Width: 16” Structural overhead guard for operator protection.
Replaceable polyurethane composition
OTHER STANDARD FEATURES:
STEERING: Back up alarm, horn, strobe light, operator seat
90 degree steering of rear wheels. complete with safety belt and electric switch.
OSCILLATING REAR STEERING BOX:
Keeps all steering wheels in contact with ground.
GRADABILITY:
OPTIONAL EQUIPMENT
Unloaded maximum grade is 20% RADIO REMOTE CONTROL:
Loaded maximum grade is 8% Radio remote control allows full machine functionality
GROUND BEARING PRESSURE: from a wireless radio remote. Allows operator optimal
Loaded Front Tires: 634 psi view of load. Emergency safety shutdown switch is
Unloaded Rear Tires: 502 psi standard.
TRAVEL SPEED UNLOADED: 110 TON SPINNER:
Travel Mode - High Gear = 0.0 to 1.70 mph Allows for 360 degree rotation of load
Travel Mode - Low Gear = 0.0 to 1.38 mph HYDRAULIC WINCH:
Work Mode - Low Gear = 0.0 to 0.42 mph Consult factory for available capacities
TELESCOPING COUNTERWEIGHT: FORKLIFT ATTACHMENT:
Standard counterweight section telescopes 5’ Consult factory for available capacities
using (2) hydraulic cylinders. Push button control. JIB EXTENSION:
HYDRAULIC RESERVOIR: Consult factory for available capacities
160 gallons (606 liters)

50
 TWINLIFT
110 TON

DIMENSIONAL DATA

51
 TWINLIFT
110 TON

REFERENCE CAPACITY / RANGE DIAGRAM

NOTE
1. The above chart is for reference purposes only.
2. Never use the above chart for lift planning calculations
3. Lift plan calculations are to be determined solely by the load charts and range diagrams that are issued for
the specific serial numbered machine that is to be used for the specific planned lift.

52
 TWINLIFT
110 TON

RANGE DIAGRAM

NOTE
1. The above chart is for reference purposes only.
2. Never use the above chart for lift planning calculations
3. Lift plan calculations are to be determined solely by the load charts and range diagrams that are issued for
the specific serial numbered machine that is to be used for the specific planned lift.

53
 TWINLIFT
110 TON

LOAD CHARTS FOR “A” COUNTERWEIGHT

LOAD CHARTS FOR “A” AND “B” COUNTERWEIGHT

54
 TWINLIFT
110 TON

LOAD CHARTS FOR “A”, “B”, AND “C” COUNTERWEIGHT

LOAD CHARTS FOR “A”, “B”, “C”, AND “D” COUNTERWEIGHT

55
 TWINLIFT
110 TON

LOAD CHARTS FOR “A”, “B”, “C”, “D”, AND “E” COUNTERWEIGHT

NOTE:

Specifications are provided in imperial dimensions. All equipment dimensions, designs, specifications, calculations, etc., as described, are
subject to change at manufacturer’s discretion at any time and without notice. Weights are approximate and may vary. Data herein is for
informational purposes only and will not be construed to guarantee suitability of equipment for any particular as performance my vary with
conditions encountered. Warranty will apply as written in standard contract form upon purchase of equipment. Capacities are for reference
only and must not be used for any serial numbered machine. Serial numbered load charts may be obtained from Lift Systems, Inc.

LIFT SYSTEMS, INC. TEL: +1-309-764-9842

OFFICE: MAILING ADDRESS: FAX: +1-309-764-9848
1505 - 7th Street P.O. Box 906 EMAIL: [email protected]
East Moline, IL 61244 Moline, IL 61266 WEB: www.lift-systems.com

56
 TF45/60
by
LIFT SYSTEMS, INC.

Global Leaders in Specialized

Lifting Equipment!
57
 TF45/60
GENERAL SPECIFICATIONS

STANDARD EQUIPMENT
ENGINE: FORKS:
GM 3.0L, 4 cylinder, 75 hp (56 Kw) propane engine 8’ self leveling forks. Tilt angle controlled from operating
PUMP: station.
Sundstrand 40 series drive pump WEIGHT:
CONTROL SYSTEM: 32,000 lbs base unit
CARL (Computer Assisted Remote Lifting) Control System. Standard “A” counterweight included
Monitors Boom Angle, Boom Extension, Pressure, COUNTERWEIGHTS:
Counterweight Load Pin. Automatic Shutdown for overload “A” - non-removable counterweight installed in unit
conditions. Large easy to read display screen with push Four (4) additional counterweight plates included with fork lift
button navigation and dial adjustment. loops standard. Weight of each plate is 5,500 lbs.
CONTROLS: Total of additional counterweight is 22,000 lbs.
Separate controls for each function. TIE DOWN / LIFTING EYES:
Combination of foot pedal, joystick, and push Tie down / lifting eyes installed for securing unit during
button controls allows for multiple functions to be transport and for lifting of the unit.
performed at the same time. DRIVER PROTECTION GUARD:
DRIVE: Structural overhead guard for operator protection.
Rockwell planetary drive axle. Full hydrostatic system with OTHER STANDARD FEATURES:
spring applied brakes. Back up alarm, horn, strobe light, operator seat
WHEELS: complete with safety belt and electric switch.
Front: qty. (4)
Diameter: 28”
Width: 12”
Rear: qty. (2)
Diameter: 28” OPTIONAL EQUIPMENT
Width: 12”
Replaceable polyurethane composition
OSCILLATING REAR STEERING BOX:
Keeps all steering wheels in contact with ground.
GRADABILITY: RIGGERS BOOM:
Unloaded maximum grade is 26% Hydraulic riggers boom attaches to fork attachment with the
Loaded maximum grade is 15% forks removed.
18,000 lbs of draw bar pull unloaded MOBILIFT BOOM:
TRAVEL SPEED UNLOADED: 7’ boom pins on end of power section in place of fork
High Gear: 2.75 mph attachment. Requires winch and block.
Low Gear: 0.75 mph WINCH:
TELESCOPING COUNTERWEIGHT: High performance hydraulic winch. Integral, full load brake.
Standard counterweight section telescopes 4’ 250’ of high capacity 5/8” wire rope standard.
using a hydraulic cylinder. Push button control. BLOCK:
HYDRAULIC RESERVOIR: 30 (27) ton block standard. Low profile with swivel hook.
90 gallons (340 liters) ANTI-TWO-BLOCK DEVICE:
BOOM: Safety device installed to prevent hook block from contacting
High strength two section telescoping boom. Replaceable boom.
wear pads on all sliding sections. RADIO REMOTE CONTROL:
BOOM LIFT CYLINDER: Radio remote control allows full machine functionality from a
Single cylinder capable of lifting and lowering with a full load. wireless radio remote. Allows operator optimal view of load.
Integral safety holding valve. Spherical bearing ensures con- Emergency safety shutdown switch is standard.
stant alignment with the boom. JIB EXTENSION:
BOOM TELESCOPE CYLINDER: Consult factory for available capacities
Single cylinder capable of telescoping the boom in and out
with a full load. Integral safety holding valve.
58
 TF45/60
AS A FORKLIFT

DIMENSIONAL DATA

59
 TF45/60
AS A FORKLIFT

LOAD CHARTS FOR FORKLIFT WITH COUNTERWEIGHT EXTENDED

LOAD CHARTS FOR FORKLIFT WITH COUNTERWEIGHT RETRACTED

60
 TF45/60
WITH RIGGERS BOOM OPTION

DIMENSIONAL DATA

61
 TF45/60
WITH RIGGERS BOOM OPTION
RANGE DIAGRAM / LOAD CHART WITH COUNTERWEIGHT EXTENDED

62
 TF45/60
WITH RIGGERS BOOM OPTION
RANGE DIAGRAM / LOAD CHART WITH COUNTERWEIGHT RETRACTED

63
 TF45/60
WITH MOBILIFT BOOM OPTION

DIMENSIONAL DATA

64
 TF45/60
WITH MOBILIFT BOOM OPTION

RANGE DIAGRAM

NOTE
1. The above chart is for reference purposes only.
2. Never use the above chart for lift planning calculations
3. Lift plan calculations are to be determined solely by the load charts and range diagrams that are issued for
the specific serial numbered machine that is to be used for the specific planned lift.

65
 TF45/60
WITH MOBILIFT BOOM OPTION
LOAD CHART WITH COUNTERWEIGHT EXTENDED

LOAD CHART WITH COUNTERWEIGHT RETRACTED

LIFT SYSTEMS, INC. TEL: +1-309-764-9842

OFFICE: MAILING ADDRESS: FAX: +1-309-764-9848
1505 - 7th Street P.O. Box 906 EMAIL: [email protected]
East Moline, IL 61244 Moline, IL 61266 WEB: www.lift-systems.com

66
THIS PAGE INTENTIONALLY LEFT BLANK

67
 CARL
LOAD MANAGEMENT SYSTEM
MOBILE EQUIPMENT
WHAT IS CARL?
CARL (Computer Assisted Remote Lifting) is the standard control
platform for all of Lift Systems’ current Mobile Equipment Line. Using
state-of-art-technology, the operator is informed of all important aspects
of the unit and lift such as boom angle, boom extension, and system
pressures, at all times.

The CARL display module interacts with all functions of the machine
and provides feedback to the operator in an easy to read and easy to
navigate platform. Radio Remote Control is also an option with the
CARL System. All functions of the unit can be performed from a belly
pack—emergency stop button standard.

Engine speed is controlled through the CARL Control System

automatically to save fuel, yet provides additional power when needed.
Manual throttle adjustment control is retained to allow the operator to
regulate engine speed if desired. Additionally, the electric over
hydraulic nature of the CARL System allows the operator to change the
speed of certain functions to best suit the task at hand.

Unsafe situations are prevented with the CARL System. A load

sensing pin in the counterweight box prevents tipping and unsafe
conditions based on the amount of counterweight added and
counterweight position.

Most existing Lift Systems’ Mobile Equipment can be retrofitted with the
CARL System. Contact your representative for details and pricing!

DISPLAY ON 75 TON MOBILIFT

68
CARL FOR MOBILE EQUIPMENT— MAIN DISPLAY PAGE

CARL FOR MOBILE EQUIPMENT— SERVICE PAGE

LIFT SYSTEMS, INC. TEL: +1-309-764-9842

OFFICE: MAILING ADDRESS: FAX: +1-309-764-9848
1505 - 7th Street P.O. Box 906 EMAIL: [email protected]
East Moline, IL 61244 Moline, IL 61266 WEB: www.lift-systems.com

69
 RECERTIFICATION PROGRAM
MOBILE EQUIPMENT

MOBILE EQUIPMENT INSPECTIONS AND ACTIONS

 Visual inspection of all welds

 Visual inspection for any physical damage to the machine
 Visual inspection of cylinders for external leaks and meter tested for internal
leakage
 Counterbalance valves, safety valves, and relief valves are pulled, cleaned,
inspected, and reset to factory specifications
 Visual inspection of all hydraulic lines and connections while under pressure
 Hydraulic oil sample is drawn and sent to an independent laboratory for testing
and analysis
 Check drive system pressure, drive speed in forward and reverse, and
drive chain tension (if applicable)
 Inspect wire rope, sheaves, and hook block for wear and damage (if applicable)
 Inspect tires for wear and damage
 Lubricate all bearings and slider pads
 Change all hydraulic oil filters
 Change engine oil and filters
 Coolant tested
 Change spark plugs (if applicable)
 Certified Load Test completed

Upon successful completion of the program, the mobile equipment owner will
receive an Official Recertification Letter and Testing Certification Document

LIFT SYSTEMS, INC. TEL: +1-309-764-9842

OFFICE: MAILING ADDRESS: FAX: +1-309-764-9848
1505 - 7th Street P.O. Box 906 EMAIL: [email protected]
East Moline, IL 61244 Moline, IL 61266 WEB: www.lift-systems.com

70