CHRYSO® ELASTOTHANE PUR

Spray Applied Fast setting Polyurea Based Elastomeric

Description tunnel lining, swimming pool, Green roof, etc. Using suitable
primer, CHRYSO ELASTOTHANE-PUR can be applied on concrete,
CHRYSO ELASTOTHANE-PUR is a spray applied 2 component steel, aluminium, GRP Plastics, wood, SPF, etc.
fast curing hybrid polyurea system for high performance
waterproofing and protective system. CHRYSO ELASTOTHANE- Method of Application
PUR is free from solvent with 100% solid with zero VOC. Part A Surface Preparation
consists of Isocyanate and Part B consists of Resin
Indicative Characteristics Surface Preparation - Concrete
The surfaces to be applied should be dry, cleaned and free from
Appearance of cured film Grey other color may also oil and grease. Loose particles should be removed and damaged
be available on request spots repaired first. Cracks should be filled up using CHRYSO
Specific Gravity at 27⁰C 1.0-1.1 ARMOURCRETE cement MORTAR / epoxy mortar. BITUTHANE
Solid content, % (w/w) 100 –PU/ ARMOURCOTE PRIMER is recommended to improve the
Mixing Ratio, by volume 1:1 adherence of CHRYSO ELASTOTHANE PUR membrane on the
Gel time, Sec 5-20 substrate as a primer coat. Ensure the surface moisture is not
Tack free time < 2 minutes more than 6% and relative humidity is not more than 80% prior
to application of primer and coating. Ensure that the substrate
Handling 40-90 minutes
must be protected against rising damp where CHRYSO
Elongation at break, %, ASTM 350±50
ELASTOTHANE –PUR is to be applied.
D412
Tensile Strength, N/mm2, ASTM >15
Mixing
D 412
Tear Resistance, N/mm, ASTM >225 N/2.5mm
Stir well before using of ELASTOTHANE –PUR. For pigmented
D 624C
system, add and mix pigment paste with Part B (Amine) with a
Taber Abrasion, ASTM D4060 < 18 mg, (CS 17 wheel)
help of barrel stirrer to uniform color.
(1kg, 1000 cycle)
Water Absorption < 1% Application
Crack bridging Capacity >2.5mm
Pull off adhesion, ASTM D 4541 2MPa (concrete failure) A suitable high pressure plural component spray equipment
Shore D 40±5 fitted with temperature controller is used to apply CHRYSO
Service temperature -40°C to +180 °C ELASTOTHANE PUR. Recoating should be carried out within 1-3
Recommended thickness and 1.5-3mm; 1kg/mm/m2 hours after the application of previous coat
Coverage
Top Coat
Domains of Application
CHRYSO ELASTOTHANE-PUR is not a color stable system when
High performance waterproofing of bridge deck, basement, exposed to UV rays. For color stable appearance in exposed
waste water tank lining, roof, terrace, podium, truck bed lining, condition use Color fast CHRYSO ELASTOTHANE – EPU as top
coat (0.1-0.2mm) over the CHRYSO ELASTOTHANE PUR.
(For more information and choice of top coat consult CHRYSO
Technical team)

The information contained in this technical data sheet is given to the best of our knowledge and the results from extensive testing in order to remain as objective as possible.
AB/25/02/2020

However, it cannot, in any case be considered as a warranty involving our liability in case of misuse or any different use of our products from the “Application” paragraph of this
technical data sheet. Some application tests should be carried out before using the product to ensure that the methods of use and conditions of application of the product are
satisfactory. Our technical assistance is at the disposal of the users.
Consult the latest update of the technical data sheet on our website www.chryso.com

CHRYSO India Private Limited | Registered & Corporate Office : Plot No. D -30/7, TTC Industrial Area, M.I.D.C. Turbhe, Navi
Mumbai – 400705. Maharashtra, INDIA. Tel : +91 22 27685991/2
CHRYSO® ELASTOTHANE PUR
Spray Applied Fast setting Polyurea Based Elastomeric
Protective / Waterproofing Coating

Advantages Precautions

 Green product – 100% solid with zero VOC  Store the material at the 5⁰ to 35⁰C temperature range
in shaded cool place and keep it away from fire and any
 Being a fast setting system installation time is
heated body. Clean all tools with MEK or any standard
minimum solvent.
 Do not keep left over material in open condition.
 Seamless system – no joints
 Dot not apply the coating if the rain is expected within
 Very high mechanical properties 3-4 hours.
 Excellent crack bridging capacity.
Safety
 Resistant to most of chemicals and solvent
 Wear hand gloves, safety shoes and safety goggles
 Excellent low and high temperature flexibility
while using and handling the product.
 Fully bonded with substrate
 In case eyes or mouth are affected wash with plenty of
 No sagging on vertical and overhead application
clean water and seek medical treatment immediately.

Before use, refer to the Material Safety Data Sheet.

6 months from the date of manufacturing when stored in un-

Packing

200L drum of each Resin and Hardener.

The information contained in this technical data sheet is given to the best of our knowledge and the results from extensive testing in order to remain as objective as possible.
However, it cannot, in any case be considered as a warranty involving our liability in case of misuse or any different use of our products from the “Application” paragraph of this
AB/25/02/2020

technical data sheet. Some application tests should be carried out before using the product to ensure that the methods of use and conditions of application of the product are
satisfactory. Our technical assistance is at the disposal of the users.
Consult the latest update of the technical data sheet on our website www.chryso.com

CHRYSO India Private Limited | Registered & Corporate Office : Plot No. D -30/7, TTC Industrial Area, M.I.D.C. Turbhe, Navi
Mumbai – 400705. Maharashtra, INDIA. Tel : +91 22 27685991/2