Scribd
Upload
51 views2 pages

PIS 102505 EDGE 2K Primer Surfacer 03.2023 1

The 2K Primer Surfacer is a two-component, high-solids primer that offers excellent filling, adhesion, and gloss retention, suitable for various substrates including treated steel and aluminum. It requires proper mixing and application techniques, with specific drying and sanding recommendations. Safety precautions are essential, as the product must be mixed before use and proper protective gear should be worn during application.

Uploaded by

papakadyan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
51 views2 pages

PIS 102505 EDGE 2K Primer Surfacer 03.2023 1

The 2K Primer Surfacer is a two-component, high-solids primer that offers excellent filling, adhesion, and gloss retention, suitable for various substrates including treated steel and aluminum. It requires proper mixing and application techniques, with specific drying and sanding recommendations. Safety precautions are essential, as the product must be mixed before use and proper protective gear should be worn during application.

Uploaded by

papakadyan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

PRODUCT: 2K Primer Surfacer

PART
NUMBER: 102505 Gallon 4 units/case 24 lbs/case

DESCRIPTION: 2K Primer Surfacer is a two-component, high-solids primer surfacer that has


excellent filling characteristics. It provides excellent adhesion and gloss / color
holdout. 2K Primer Surfacer sands easily without clogging the sandpaper, while
providing excellent resistance to sand scratch swelling.

SUBSTRATES:
• Treated Steel • Refinish Lacquers,
• Treated Aluminum Enamels and Urethanes
• Fiberglass/SMC • Self-Etch Primers
• OEM Finishes • Body Filler/Putty

NOTE: Steel and Aluminum must be properly treated with an Etch Primer
or Metal Etch.

CLEANING:
• Surface must be clean and free of dirt, oil, grease and wax
• To solvent clean raw, exposed fiberglass, it is recommended to clean
exposed area with acetone.

MIXING:
4 Parts 1 Part
#2505 to #2507
2K Primer Surfacer 2K Primer Catalyst

• Shake and stir the primer and catalyst thoroughly before mixing

POTLIFE:
1 hour @ 70°F (21°C)
45 min. @ 80°F (27°C)
30 min. @ 90°F (32°C)

• Clean spray gun immediately after use

APPLICATION:

a division of Illinois Tool Works Inc. | 6600 Cornell Road | Cincinnati, OH 45242 | (513) 489-7600
©2023 Evercoat
evercoat.com
• Use a primer gun with a 1.4 to 1.8 fluid nozzle/air cap at a recommended air
pressure of 5-7 psi at the cap
• Apply 2-3 medium wet coats allowing 3-5 minutes flash time between coats

DRYING:
Air Dry: 1.5 – 3 hours @ 70°F (21°C)
Force Dry: 30 min. @ 140°F (60°C)
Dry-to-Sand: 2 hours air dry; upon cool down for force dry.

NOTE: Dry times may vary based on film build and ambient air temperature.

FINISH:
• Initial Sand: 180 – 320 grit
• Final Sand to Seal: 400 grit
• Final Sand to Topcoat: 600 grit

TECHNICAL
SPECIFICATIONS:
Appearance Gray liquid
VOC Refer to Section 9 of the Safety Data
Sheet
Recommended Dry-Film-Thickness
(DFT) after Sanding 2.0 – 2.5 mils
Maximum DFT after Sanding 6.0 mils

SAFETY &
HANDLING:

IMPORTANT: The contents of these packages must be mixed with other components before the products
can be used. Before opening the packages, be sure to understand the warnings on all labels of all
components since the resulting product will have the warnings and cautions of all its parts. Improper spray
technique may result in hazardous conditions. Follow the spray equipment manufacturer's instructions to
prevent injury or fire. Follow respirator manufacturer's directions for respirator use. Always wear eye and
skin protection. Observe all precautions. Consult MSDS for further safety information and/or handling
instructions. In case of emergency, contact your local emergency room or poison control center
immediately. For professional use only.

a division of Illinois Tool Works Inc. | 6600 Cornell Road | Cincinnati, OH 45242 | (513) 489-7600
©2023 Evercoat
evercoat.com

You might also like