GMA 347

Audio Panel
Installation Manual

190-00325-01 June, 2010 Revision F

 © Copyright 2010
Garmin Ltd. Or its subsidiaries
All Rights Reserved

Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted,
disseminated, downloaded or stored in any storage medium, for any purpose without the express prior
written consent of Garmin. Garmin hereby grants permission to download a single copy of this manual
and of any revision to this manual onto a hard drive or other electronic storage medium to be viewed and
to print one copy of this manual or of any revision hereto, provided that such electronic or printed copy of
this manual or revision must contain the complete text of this copyright notice and provided further that
any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.

Garmin International, Inc.

1200 E. 151st Street
Olathe, KS 66062 USA
Telephone: 913.397.8200
Aviation Panel-Mount Technical Support Line (Toll Free) 1.888.606.5482
www.garmin.com

Garmin (Europe) Ltd.

Liberty House, Bulls Copse Road
Hounsdown Business Park
Southampton, SO40 9RB U.K.
+44/ (0) 870.8501241

Garmin AT, Inc.

2345 Turner Rd., SE
Salem, OR 97302 USA
Telephone: 503.581.8101

RECORD OF REVISIONS

Revision Revision Description

Date
A 8/24/05 Initial Release
B 6/06/06 Revised for DO-178B Level C
C 11/02/07 Added info for DO-254 and GMA 347 White LED units
D 10/10/08 Updated Mod Table for 011-00807-30 units
Added marker beacon antenna cable termination
E 9/25/09
instructions and volume configuration
F 06/18/10 Updated Appendix B

Page A GMA 347 Installation Manual

Revision F 190-00325-01
 CURRENT REVISION DESCRIPTION

Page Section
Revision Description of Change
Number(s) Number
1-7 1.6 Updated warranty statement
F
B-1 – B-6 Appdx B Updated Figures B-1, B-2, & B-3

DOCUMENT PAGINATION

Section Page Range

Table of Contents i – vi
Section 1 1-1 – 1-8
Section 2 2-1 – 2-10
Section 3 3-1 – 3-16
Section 4 4-1 – 4-14
Appendix A A-1 – A-4
Appendix B B-1 – B-6
Appendix C C-1 – C-12

GMA 347 Installation Manual Page i

190-00325-01 Revision F
This manual reflects the operation of software version 4.00 or later. Some differences in operation may
be observed when comparing the information in this manual to earlier or later software versions.

INFORMATION SUBJECT TO EXPORT CONTROL LAWS

This document may contain information which is subject to the Export Administration Regulations
("EAR") issued by the United States Department of Commerce (15 CFR, Chapter VII, Subchapter C) and
which may not be exported, released, or disclosed to foreign nationals inside or outside of the United
States without first obtaining an export license. The preceding statement is required to be included on
any and all reproductions in whole or in part of this manual.

WARNING

This product, its packaging, and its components contain chemicals known to the state of
California to cause cancer, birth defects, or reproductive harm. This notice is being
provided in accordance with California’s proposition 65. If you have any questions or
would like additional information, please refer to our web site at
www.garmin.com/prop65.

Page ii GMA 347 Installation Manual

Revision F 190-00325-01
 TABLE OF CONTENTS

PARAGRAPH PAGE

1 GENERAL DESCRIPTION..............................................................................................................1-1
1.1 Introduction........................................................................................................................................1-1
1.2 Equipment Description ......................................................................................................................1-1
1.3 Technical Specifications ...................................................................................................................1-3
1.4 Certification .......................................................................................................................................1-5
1.5 Reference Documents ........................................................................................................................1-6
1.6 Limited Warranty...............................................................................................................................1-7

2 INSTALLATION OVERVIEW ........................................................................................................2-1

2.1 Introduction........................................................................................................................................2-1
2.2 Wiring ................................................................................................................................................2-1
2.3 Cooling Air ........................................................................................................................................2-1
2.4 Installation Materials .........................................................................................................................2-2
2.5 GMA 347 Wiring and Software Configuration Options....................................................................2-3
2.6 Marker Beacon Antenna Installation .................................................................................................2-6
2.7 Installation Approval Considerations for Pressurized Aircraft..........................................................2-8
2.8 Electrical Noise..................................................................................................................................2-8
2.9 GMA 347 Mounting ..........................................................................................................................2-9

3 INSTALLATION PROCEDURE......................................................................................................3-1
3.1 Unpacking Unit..................................................................................................................................3-1
3.2 Marker Beacon Antenna Installation .................................................................................................3-1
3.3 Marker Beacon Antenna Cable Connectors.......................................................................................3-1
3.4 Electrical Connections .......................................................................................................................3-1
3.5 Backshell Assembly and D-Subminiature Connectors ......................................................................3-3
3.6 Circuit Breaker Placard....................................................................................................................3-11
3.7 GMA 347 Unit Installation ..............................................................................................................3-11
3.8 Post Installation Configuration ........................................................................................................3-11
3.9 Post Installation Checkout ...............................................................................................................3-13

4 SYSTEM INTERCONNECTS..........................................................................................................4-1
4.1 Connector Description .......................................................................................................................4-1
4.2 Connectors J3471 and J3472 .............................................................................................................4-1
4.3 J3472 Connector Pin Assignments ....................................................................................................4-6
4.4 J3471 Connector Pin Assignments ..................................................................................................4-10

GMA 347 Installation Manual Page iii

190-00325-01 Revision F
PARAGRAPH PAGE

APPENDIX A CERTIFICATION DOCUMENTS

A.1 Airworthiness Approval.................................................................................................................... A-1
A.2 Continued Airworthiness .................................................................................................................. A-1

APPENDIX B ASSEMBLY AND INSTALLATION DRAWINGS

APPENDIX C INTERCONNECT DRAWINGS

LIST OF ILLUSTRATIONS

FIGURE PAGE

2-1 GMA Marker Beacon Coaxial Cable D-Sub Termination.................................................................2-7

2-2 GMA 347 Unit Rack .........................................................................................................................2-9

3-1 Shield Block Install onto Backshell Connector Assembly ................................................................3-4

3-2 Shielded Cable Preparation................................................................................................................3-5
3-3 Daisy Chain Method for Shield Termination.....................................................................................3-8
3-4 Parallel Shield Termination ...............................................................................................................3-8
3-5 Configuration Module Installation...................................................................................................3-10

4-1 Backshell Rear Connector Plate.........................................................................................................4-1

4-2 Rear Connectors J3471 and J3472, Viewed From Back of Unit .......................................................4-1
4-3 GMA 347 Configuration Upload Connections ..................................................................................4-7

B-1 GMA 347 Outline Drawing .............................................................................................................. B-1

B-2 GMA 347 Connector/Rack Assembly Drawing ............................................................................... B-3
B-3 GMA 347 Recommended Panel Cutout Dimensions ...................................................................... B-5

C-1 GMA 347 Power, Antenna, and Speaker Interconnect Wiring Diagram.......................................... C-1
C-2 Mic and Phone Jack Connections, Interconnect Wiring Diagram .................................................... C-3
C-3 Transceiver Analog Connections, Interconnect Wiring Diagram..................................................... C-5
C-4 GMA 347 Typical Garmin Integrated Flight Deck Digital Interconnect Wiring Diagram .............. C-7
C-5 Discrete Lines, Interconnect Wiring Diagram .................................................................................. C-9
C-6 GMA 340 to GMA 347 Comparison .............................................................................................. C-11

Page iv GMA 347 Installation Manual

Revision F 190-00325-01
 LIST OF TABLES

TABLE PAGE

2-1 Pin and Crimp Tool Part Numbers.....................................................................................................2-7

3-1 Pin Contact Part Numbers (Hi Density).............................................................................................3-1
3-2 Recommended Crimp Tools (Hi Density) .........................................................................................3-2
3-3 Backshell Assembly (011-00812-00) ................................................................................................3-3
3-4 Shield Block Components .................................................................................................................3-4
3-5 Shielded Cable Preparation................................................................................................................3-5
3-6 Configuration Module Kit – 011-00979-00.......................................................................................3-9
3-7 Configuration Module Wire Color Reference Chart .......................................................................3-10
3-8 GMA 347 System Configuration.....................................................................................................3-11
4-1 J3471 Pin Assignments......................................................................................................................4-2
4-2 J3472 Pin Assignments......................................................................................................................4-4

GMA 347 Installation Manual Page v

190-00325-01 Revision F
 GMA 347 HARDWARE MOD LEVEL HISTORY
The following tables identify hardware modification (Mod) Levels for the GMA 347 Audio Panel. Mod
Levels are listed (for each GMA 347 part number) with the associated service bulletin number, service
bulletin date, and the purpose of the modification. The tables are current at the time of publication of this
manual (see date on front cover) and are subject to change without notice. Authorized Garmin Sales and
Service Centers are encouraged to access the most up-to-date bulletin and advisory information on the
Garmin Dealer Resource web site at www.garmin.com using their Garmin-provided user name and
password.

GMA 347 P/N 011-00807-00 HARDWARE MOD LEVEL HISTORY

MOD SERVICE SERVICE PURPOSE OF MODIFICATION

LEVEL BULLETIN BULLETIN
NUMBER DATE

GMA 347 P/N 011-00807-10 HARDWARE MOD LEVEL HISTORY

MOD SERVICE SERVICE PURPOSE OF MODIFICATION

LEVEL BULLETIN BULLETIN
NUMBER DATE

GMA 347 P/N 011-00807-20 HARDWARE MOD LEVEL HISTORY

MOD SERVICE SERVICE PURPOSE OF MODIFICATION

LEVEL BULLETIN BULLETIN
NUMBER DATE

GMA 347 P/N 011-00807-30 HARDWARE MOD LEVEL HISTORY

MOD SERVICE SERVICE PURPOSE OF MODIFICATION

LEVEL BULLETIN BULLETIN
NUMBER DATE

Increase LED brightness, improve manual squelch

1 SB0839 10/20/08 adjustment sensitivity, and improve gain of telephone
interface circuitry

Page vi GMA 347 Installation Manual

Revision F 190-00325-01
1 GENERAL DESCRIPTION
1.1 Introduction
This manual presents mechanical and electrical installation requirements for installing the Garmin
GMA 347 Audio Panel. The GMA 347 can be installed into a variety of airframes by means of an STC,
TC, or Field Approval. Each airframe installation may vary. Use only approved data for specific
installation instructions in a particular aircraft. After installation of the GMA 347, FAA Form 337 must
be completed by an appropriately certificated agency to return the aircraft to service.

1.2 Equipment Description

CAUTION

The operation of cellular telephones or other cellular mobile devices aboard aircraft while
airborne is prohibited by FCC rules. Due to the potential for interference with onboard
systems, the operation of cellular communication devices while onboard an aircraft that is
on the ground is subject to (FAA) 14 CFR 91.21.

(FCC) 47 CFR 22.925 prohibits airborne operation of cellular telephones installed in or

carried aboard aircraft. Cellular telephones must not be operated aboard any aircraft
while the aircraft is off the ground. When any aircraft leaves the ground, all cellular
telephones on board that aircraft must be turned off.

Cellular telephones that are on, even in a monitoring state, can disrupt GPS performance.

The GMA 347 (unit only) is available in four different part numbers (Section 2.4.1) that are referred to as
the GMA 347 (in Black or Grey bezel), GMA 347H (Helicopter), and the GMA 347 White LED. The
GMA 347 is the standard version audio panel, which is available with a black or a grey bezel. The GMA
347H (Helicopter) version has the pilot and copilot control knobs on the front panel reversed from the
standard GMA 347 positions, and is available only with a black bezel. The GMA 347 White LED
version has white LEDs that illuminate the keys (as opposed to the green LEDs on the standard version),
and is available only with a black bezel.

The Garmin GMA 347 is a horizontally oriented panel-mounted audio control panel and marker beacon
system. The system delivers reliability and versatility for all audio controlling functions. LED-
illuminated pushbuttons and logical panel layout allow audio selection of NAV, COM, ADF, Marker
Beacon, and TEL. LED annunciator brightness is adjusted to an appropriate level for ambient cockpit
light conditions automatically by photocell dimming. Key brightness is controlled manually with the
radio lighting dimming bus. A failsafe circuit connects the pilot’s left headset channel and microphone
directly to COM 1 in case power is interrupted or the unit is turned off.

The Garmin GMA 347 Audio Panel incorporates a microcontroller for processing front panel key
commands, annunciator control, input/output functions, and communication.

The GMA 347 includes a six-position intercom system (ICS) with electronic cabin noise de-emphasis,
two stereo music inputs, and combined pilot, copilot, and passenger volume controls. The intercom
provides four selectable modes of isolation (All, Crew, Pilot, Copilot). A pilot-selectable cabin speaker
output can be used to listen to the selected aircraft radios or to broadcast PA announcements. The PA
function is pilot selectable.

GMA 347 Installation Manual Page 1-1

190-00325-01 Revision F
The GMA 347 provides a digital voice recorder with playback capability. Recording is automatic when a
COM signal is received. Playback is controlled by pressing the PLAY button or a remote mounted
switch.

The Recorder can be disabled using an external switch. The digital recorder can playback up to two and a
half minutes of recording. Refer to the GMA 347 Pilot’s Guide (190-00325-00) for complete system
operation.

A marker beacon receiver with dual sensitivity and audio muting with automatic re-arming is included in
the unit. Operating voltage range is 14/28 Vdc.

The GMA 347 provides two stereo auxiliary entertainment inputs; MUSIC 1 and MUSIC 2. Two 3.5 mm
stereo phone jacks should be installed in a convenient location for this purpose. These inputs are
compatible with popular portable entertainment devices such as MP3 and CD players. The headphone
outputs of these devices are plugged into the MUSIC 1 or MUSIC 2 jacks.

Only the pilot and copilot hear MUSIC 1. MUSIC 2 is a non-muted input heard only by the passengers.
MUSIC 1 and MUSIC 2 characteristics are affected by the active intercom mode. Refer to the GMA 347
pilot’s manual for details.

MUSIC 1 is soft-muted when an interruption occurs from an aircraft radio. Soft muting is the gradual
return of MUSIC 1 to its original volume level. MUSIC 1 can also be configured to mute during ICS
activity. MUSIC 2 is a non-muted input.

1.2.1 Features Summary

• Logical front panel layout

• LED annunciators indicate selected function
• Six position intercom: pilot, copilot, four passengers
• Three stereo headset amplifiers: one for pilot, one for copilot, and one for the passengers
• Two stereo music source inputs
• Four selectable intercom operational modes
• Independent pilot, copilot, and passenger volume control
• VOX control for mic inputs
• Automatic selection of radio audio source when corresponding mic is selected
• MASQTM Processing
• Split COM transceiver function. Copilot may transmit and receive on COM 2 while pilot
transmits and receives on COM 1
• COM swap function
• TX indication
• SmartMuteTM marker audio muting
• Autosquelch
• Speaker output for radios or PA function
• Power-off fail safe connection for Pilot PTT, mic and Pilot’s Headset-Left to COM 1
• Voice Recorder with Playback
• Configurable Options. See Sections 3 and 4 for connection and configuration details.
Page 1-2 GMA 347 Installation Manual
Revision F 190-00325-01
1.2.2 Interface Summary
The following is an interface summary for the GMA 347. See Section 4 and Appendix C for connection
details.

• 3 Transceiver Inputs/Outputs (Figure C-3)

• 1 Speaker Output (Figure C-1)
• 3 Headset Outputs (Figure C-1)
• 5 Receiver Inputs (Figure C-3)
• 4 Unswitched Inputs (Figures C-3)
• 2 Aircraft Power Inputs (Figure C-1)
• Discrete Inputs/Outputs (Figure C-4)
• Marker Beacon Antenna Input (Figure C-1)
• External Marker Beacon Lamp Driver Outputs (Figure C-4)

1.3 Technical Specifications

It is the responsibility of the installing agency to obtain the latest revision of the GMA 347 Environmental
Qualification Form. This form is available directly from Garmin under the following part number:

GMA 347 Environmental Qualification Form, Garmin part number 005-00155-79

To obtain a copy of this form, see the dealer/OEM portion of the Garmin web site (www.garmin.com).

1.3.1 Physical Characteristics

Specification Characteristic
Bezel Height 1.30 inches (33 mm)
Bezel Width 6.29 inches (160 mm)
Rack Height 1.33 inches (34 mm)
Rack Width 6.30 inches (160 mm)
Depth Behind Panel with Connectors 7.79 inches (198 mm)
(measured from face of aircraft panel to rear
of connector backshells)
GMA 347 Unit Weight 1.7 lbs. (0.8 kg)
GMA 347 Rack Weight (Installed with rack 2.4 lbs. (1.1 kg)
and connectors)

GMA 347 Installation Manual Page 1-3

190-00325-01 Revision F
1.3.2 Electrical Characteristics
Specification Characteristic
Regulatory Compliance RTCA/DO-160D Environmental Conditions and EUROCAE/ED-14D

Temperature Range -45°C to +70°C

Altitude 55,000 Feet

Audio Panel Transceiver inputs: 3

Receiver inputs: 5
Unswitched inputs: 4
Input impedance: 500 Ω
Input isolation: 60 dB minimum
TM
Special functions: Failsafe operation, MASQ
processing
Maximum Input: COM, NAV, DME, AUX, Failsafe, Unswitched inputs 1-3,
Altitude Warning; 4 V rms
TEL; 3.5 V rms
Intercom Positions: 6 (pilot, copilot, 4 passengers)
Volume controls: 3 (pilot, copilot, passengers)
VOX level controls: 2 (pilot, copilot/passengers)
VOX circuits: 6 (one per mic input)
Music inputs (stereo): 2 (one input mutable)
Music input impedance: 5 kΩ
Music input level: Less than 500 mVac RMS for full output (typical).
1 Vac RMS MAX (3 Vp-p)
Microphone signal processing: 9 pole characteristic and special cabin noise
band de-emphasis
Intercom isolation modes: 4 (All, Pilot Isolate, Copilot Isolate, Crew Isolate)
Special functions: Recorder with playback (automatic recording of selected
COMs) up to 2.5 minutes of recording time.
Automatic squelch: 6 (one per mic input) pilot selectable between auto and
manual.
Headphone Outputs Output amplifiers: 3, stereo (pilot, copilot, passengers)
Fidelity: Power into 150 Ω Distortion
50 mW <0.5%
100 mW <5%
Frequency response: music; 50 Hz to 20 kHz nominal
Aircraft radio: 200 Hz to 6 kHz nominal
ICS mic: (Special cabin noise band de-emphasis)
Speaker Outputs Outputs selectable: 1, pilot selectable
Output power: 10 watts into 4 Ω or 8 Ω, @ any normal supply voltage.
Frequency response: 350 Hz to 6 kHz nominal
Special functions: PA Mode, pilot selectable, including split operation
Marker Beacon Receiver Frequency: Crystal controlled at 75 MHz
Sensitivity: LO 1000 µV hard; HI 200 µV hard
Selectivity: 6 dB @ ±10 kHz min, 40 dB @ ±200 kHz max.
Input impedance: 50 Ω
External lamp drive: 125 mA max each output
Other outputs: Middle MKR sense
TM
Special functions: SmartMute marker audio muting

Page 1-4 GMA 347 Installation Manual

Revision F 190-00325-01
1.3.3 Power Requirements

Characteristic Specification
Input Voltage Range 14/28 Vdc. See the Environmental Qualification Form for details
on surge ratings and minimum/maximum operating voltages.
Power Input Operating Current:
3.75 amps max at 13.75 V
1.75 amps max at 27.5 V

1.4 Certification
The conditions and tests required for TSO approval of this article are minimum performance standards. It
is the responsibility of those installing this article either on or within a specific type or class of aircraft to
determine that the aircraft installation conditions are within the TSO standards. TSO articles must have
separate approval for installation in an aircraft. The article may be installed only if performed under 14
CFR part 43 or the applicable airworthiness requirements.

1.4.1 TSO/ETSO Compliance

Function TSO/ETSO Classification

Audio Selector Panels TSO-C50c
Not Applicable
And Amplifiers ETSO-C50c
Airborne Radio Marker TSO-C35d
Class A
Receiving Equipment ETSO-2C35d

1.4.1.1 Software Level Qualifications

Applicable Image P/N Standard Qualification Level Applicable LRU Part

Numbers
006-B0203-33 011-00807-00
006-B0203-35 DO-178B C 011-00807-10
006-B0203-4 () 011-00807-20
006-B0203-4 () DO-178B C 011-00807-30
011-00807-00
006-B0203-0 ()
DO-178B D 011-00807-10
006-B0203-1 ()
011-00807-20

1.4.1.2 Complex Hardware Level Qualifications

Applicable Image Standard Qualification Level Applicable LRU

P/N Part Numbers
006-B0203-4 () DO-254 C All

GMA 347 Installation Manual Page 1-5

190-00325-01 Revision F
1.4.2 TSO/ETSO Deviations
The following table provides a list of applicable TSO/ETSO deviations for the GMA 347.

TSO Deviation
Garmin was granted a deviation from TSO-C35d to use RTCA DO-160D instead
of RTCA DO-138 as the standard for Environmental Conditions and Test
TSO-C35d Procedures for Airborne Equipment.
Garmin was granted a deviation from TSO-C35d to use FAR §21.607(d) instead
of FAR §37.7 as the general rules governing holders of the TSO authorizations.
Garmin was granted a deviation from TSO-C50d to use RTCA DO-178B instead
of RTCA DO-178A as the standard for Software Considerations in Airborne
Systems and Equipment Certification.
TSO-C50d
Garmin was granted a deviation from TSO-C50d to use RTCA DO-160D instead
of RTCA DO-160A as the standard for Environmental Conditions and Test
Procedures for Airborne Equipment.

1.5 Reference Documents

The following publications are sources of additional information for installing the GMA 347. Before
installing the unit, the technician should read all referenced materials along with this manual.

Part Number Document

190-00325-00 GMA 347 Pilot’s Guide

Page 1-6 GMA 347 Installation Manual

Revision F 190-00325-01
1.6 Limited Warranty
All Garmin avionics products are warranted to be free from defects in materials or workmanship for: two
years from the date of purchase for new Remote-Mount and Panel-Mount products; one year from the
date of purchase for new portable products and any purchased newly-overhauled products; six months for
newly-overhauled products exchanged through a Garmin Authorized Service Center; and 90 days for
factory repaired or newly-overhauled products exchanged at Garmin in lieu of repair. Within the
applicable period, Garmin will, at its sole option, repair or replace any components that fail in normal use.
Such repairs or replacement will be made at no charge to the customer for parts or labor, provided that the
customer shall be responsible for any transportation cost. This warranty does not apply to: (i) cosmetic
damage, such as scratches, nicks and dents; (ii) consumable parts, such as batteries, unless product
damage has occurred due to a defect in materials or workmanship; (iii) damage caused by accident, abuse,
misuse, water, flood, fire, or other acts of nature or external causes; (iv) damage caused by service
performed by anyone who is not an authorized service provider of Garmin; or (v) damage to a product
that has been modified or altered without the written permission of Garmin. In addition, Garmin reserves
the right to refuse warranty claims against products or services that are obtained and/or used in
contravention of the laws of any country.
THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF
ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING
ANY LIABILITY ARISING UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE, STATUTORY OR OTHERWISE. THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO STATE.
IN NO EVENT SHALL GARMIN BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR
CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE OR
INABILITY TO USE THE PRODUCT OR FROM DEFECTS IN THE PRODUCT. SOME STATES DO
NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
Garmin retains the exclusive right to repair or replace (with a new or newly-overhauled replacement
product) the product or software or offer a full refund of the purchase price at its sole discretion. SUCH
REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF
WARRANTY.
Online Auction Purchases: Products purchased through online auctions are not eligible for warranty
coverage. Online auction confirmations are not accepted for warranty verification. To obtain warranty
service, an original or copy of the sales receipt from the original retailer is required. Garmin will not
replace missing components from any package purchased through an online auction.
International Purchases: A separate warranty may be provided by international distributors for devices
purchased outside the United States depending on the country. If applicable, this warranty is provided by
the local in-country distributor and this distributor provides local service for your device. Distributor
warranties are only valid in the area of intended distribution. Devices purchased in the United States or
Canada must be returned to the Garmin service center in the United Kingdom, the United States, Canada,
or Taiwan for service.

Garmin International, Inc. Garmin (Europe) Ltd.

1200 E. 151st Street Liberty House
Olathe, KS 66062, U.S.A. Bulls Copse Road
Phone: 800/800.1020 Hounsdown Business Park
FAX: 913/397.0836 Southampton, SO40 9RB, UK
Telephone: 44 (0) 8708501241

GMA 347 Installation Manual Page 1-7

190-00325-01 Revision F
 This page intentionally left blank

Page 1-8 GMA 347 Installation Manual

Revision F 190-00325-01
2 INSTALLATION OVERVIEW
2.1 Introduction
This section provides hardware equipment information for installing the GMA 347 Audio Panel, related
hardware and suggestions relating to the marker beacon antenna. The guidance of FAA advisory circulars
AC 43.13-1B and AC 43.13-2B, where applicable, may be found useful for making retro-fit installations
that comply with FAA regulations.

2.2 Wiring
Use AWG #22 or larger wire for all connections unless otherwise specified in the interconnect diagrams
in Appendix C. The standard pin contacts supplied in the connector kit are compatible with up to AWG
#22 wire. In cases where some installations have more than one unit sharing a common circuit breaker,
sizing and wire gauge is based on aircraft circuit breaker layout, length of wiring, current draw of units,
and internal unit protection characteristics. Do not attempt to combine more than one unit on the same
circuit breaker unless it is specified on aircraft manufacturer approved drawings.

In some cases, a larger gauge wire such as AWG #18 or #16 may be needed for power connections.
Extended barrel contacts for AWG #16 and #18 wire are available from Garmin, if required. Special thin-
wall heat shrink tubing is also provided to insulate the extended barrels inside the backshell. If using #16
or #18 barrel contacts, ensure that no two contacts are mounted directly adjacent to each other. This
minimizes the risk of contacts touching and shorting to adjacent pins and to ground.

Ensure that routing of the wiring does not come in contact with sources of heat, RF or EMI interference.
Check that there is ample space for the cabling and mating connectors. Avoid sharp bends in cabling and
routing near aircraft control cables.

2.3 Cooling Air

The GMA 347 does not have provisions for attaching cooling air and does not generate an excessive
amount of heat during typical operations, however the thermal characteristics of the installation should
always be assessed. An undesirable thermal condition could be created due to the unit's own internal
power dissipation combined with restricted ventilation, or due to heat generated by adjacent equipment.
Limiting thermal build up, by means of fan or natural convection is always a good practice and is
recommended to increase the product life.

GMA 347 Installation Manual Page 2-1

190-00325-01 Revision F
2.4 Installation Materials
2.4.1 Configurations Available

The GMA 347 is available in different versions under the following part numbers. Catalog part numbers
are shown with and without the installation kit.

Model Front Panel Unit P/N Catalog P/N Installation

Color Kit
GMA 347 Black 011-00807-00 010-00275-00 No
GMA 347 Black 011-00807-00 010-00275-01 Yes
GMA 347 Gray 011-00807-10 010-00275-10 No
GMA 347 Gray 011-00807-10 010-00275-11 Yes
GMA 347H Black 011-00807-20 010-00275-20 No
GMA 347H Black 011-00807-20 010-00275-21 Yes
GMA 347
Black 011-00807-30 010-00275-30 No
White LED
GMA 347
Black 011-00807-30 010-00275-31 Yes
White LED

2.4.2 Equipment Available

Each of the following accessories is provided separately or in kit form for the GMA 347. The installation
kit includes the unit and the following hardware:

Item Garmin P/N

Sub Assy, Connector Kit, GMA 347 011-00813-01
SMP, Install Rack, GMA 347 115-00427-00
Sub Assy, Backplate, GMA 347 011-00812-00
Configuration Module Kit 011-00979-00
Garmin Marker Beacon Antenna Kit** 010-10175-00

** Note: A marker beacon antenna approved to TSO-C35d that has been installed to meet the
requirements of this manual may be approved for use with the GMA 347.

2.4.3 Additional Equipment Required

• Antenna sealant (use manufacturer’s instructions, install according to FAA Advisory Circular
AC 43.13-2B).
• Cables: The installer will fabricate and supply all system cables. Interconnect wiring
diagrams are detailed in Appendix C.
• Hardware #6-32 x 100° Flat Head SS Screw [(MS24693, AN507R or other approved
fastener) (6 ea.)] and #6-32 Self-Locking Nut [MS21042 or other approved fastener (6 ea.)].
Hardware required to mount the installation rack is not provided.
• Stereo headphone jacks (up to 6), microphone jacks (up to 6), 3.5 mm stereo jacks (up to 2),
and insulating washers for all.

Page 2-2 GMA 347 Installation Manual

Revision F 190-00325-01
2.5 GMA 347 Wiring and Software Configuration Options
The GMA 347 can be configured in different ways for the flight crew. Consideration of options should
be discussed with the end user(s) of the aircraft before wiring begins. While Section 4 and Appendix C
contain connection details, the actual features employed or omitted are dependent on the wiring options
and the Software configuration selected. Refer to Section 3 for configuration instructions.

2.5.1 Hard Wiring Configuration Options

The following list shows the hard wiring configuration options available for the GMA 347.

Function and Purpose Hard Wiring Configuration Options

Com Swap. Transfers the active
Com Swap Pushbutton Switch
microphone between Com 1 and Com 2.
External lamps. Provides an extra set of
Marker Beacon indicators located away External Marker Beacon Lights
from the GMA 347.
Two Playback Options:
An external pushbutton activates voice Playback Pushbutton Switch
recorder playback.
A toggle switch enables or disables Record Toggle Switch
recording.
PA MUTE is an output from the GMA that
is pulled low when active. It is used to
PA mute
trigger the mute function of an external PA
system.
A remote switch can be used to enable or
Remote Auxiliary Switch
disable the auxiliary input.

GMA 347 Installation Manual Page 2-3

190-00325-01 Revision F
2.5.2 Software Configuration Options

The following list shows the software configurations available for the GMA 347. Refer to 005-00155-99
for configuration program instructions.

Function and Purpose Software Configuration

Audio Inputs. Allow or disable Enable or Disable DME, ADF, COM3, Play, PA, SPKR,
the use of external receivers TEL, and Split COM
Defeat the (MASQ) Master Deactivate MASQ
Squelch feature
Telephone. Remove telephone Disable Telephone Channel
capability
Sidetone. Disable the sound of Enable or Disable Sidetone
transmission in the headset
COM MUTE ON TX Can be disabled. Audio on unselected COMs is muted
while the selected COM is transmitting audio
COM MUTE ON RX Can be disabled. Audio on unselected COMs is muted
while the selected COM is receiving audio
Audio level. Volume control Adjust Audio level of Music 1 and Music 2, Unswitched 1,
adjustment Unswitched 2, Unswitched 3 and Altitude Warning,
SPKR, Pilot and Copilot Mic Volume, Master Squelch
Threshold, and Marker volume
Marker Threshold Marker Beacon threshold levels are adjustable for HI and
LO sense
ICS Mute ICS Muting of Music 1 can be enabled or disabled
Record COM2 Pilot or Copilot COM recording. During the Split Com
mode, COM 1 or COM 2 audio can be selected for voice
recording and playback
Disable key press beep. Disable beep heard when pressing keys.
Speaker On Power On Always turn the speaker on when the unit powers up.
Allow Music Mute Toggle When enabled, allows the pilot to turn music muting on
incoming radio off by holding the MKR/Mute key for three
seconds.

Page 2-4 GMA 347 Installation Manual

Revision F 190-00325-01
2.5.3 Transmit Interlock and Split COM Operation

NOTE
Garmin makes no expressed or implied guarantees regarding the
suitability of the Split COM feature in any given installation.

In small aircraft, COM and Nav receiver interference is affected by both the distance between antennas
and the tuned frequency separation.

With transmit interlock activated in either the GMA 347 or the COM transceivers, Split COM operation
between a flight crew of more than one pilot is affected.

In aircraft that have a transmit interlock feature, when either transmitter is keyed, all other receivers are
muted so that they won’t pick up interference from the active COM transmitter. This is the preferred
option for single pilot operation.

For aircraft with two flight crew members, transmit-interlock would likely interfere with communications.
When the pilot or the copilot transmit, no audio is heard on any other receiver. This means that if the
pilot is communicating with ATC while the copilot transmits on another radio, all pilot reception is cut
off during the time of copilot transmission.

If the installation does not have transmit-interlock activated, all the receivers are listening all the time
whether any radio is transmitting or not. Split COM performance varies significantly across installations.

If the transceivers interfere with each other, transmission by one radio produces static or squeal, thus loss
of communication from any other radio.

GMA 347 Installation Manual Page 2-5

190-00325-01 Revision F
2.6 Marker Beacon Antenna Installation
2.6.1 Location Considerations
The marker beacon antenna should be mounted on a flat surface on the underside of the aircraft body.

NOTE
Do not install the antenna inside the aircraft. Installing the antenna
inside the aircraft limits the antenna reception and increases the antennas
susceptibility to radiation from components inside the aircraft.

Mount the antenna so that there is a minimum of structure between it and the ground radio stations.
Locate it as far away as possible from transmitter antennas. Best results with split COM mode will be
obtained when the COM 1 and COM 2 antennas are mounted on opposite sides of the aircraft
(top/bottom).

2.6.2 Marker Beacon Antenna Mounting

Install the antenna according to the antenna manufacturer’s instructions. If the antenna is being installed
on a composite aircraft, ground planes must sometimes be added. Conductive wire mesh, radials or thin
aluminum sheets embedded in the composite material provide the proper ground plane allowing the
antenna pattern (gain) to be maximized for optimum performance.

2.6.3 Marker Beacon Antenna Cable Installation

Use coaxial cable meeting the applicable aviation regulation for the marker beacon antenna. Any cable
meeting specifications is acceptable for the installation. When routing antenna cables, observe the
following precautions:

• All cable routing should be kept as short and as direct as possible

• Avoid sharp bends

• Avoid routing cables near power sources (e.g., 400 Hz generators, trim motors, etc.) or near
power for fluorescent lighting

• Allow a 12 inch minimum separation between any other cables, including antenna cables (e.g
ADF, COM, NAV, GS, MARKER)

Page 2-6 GMA 347 Installation Manual

Revision F 190-00325-01
2.6.4 Marker Beacon Antenna Cable Termination
This section provides guidance for terminating the coaxial cable into the D-Sub connector. See the
system interconnect section for pin assignments.

NOTE
Use coaxial cable meeting the applicable aviation regulation for the marker beacon
antenna. Route the cable to the D-Sub as described in Section 2.6.3.

When terminating the coaxial cable into the D-Sub, observe the following guidance (refer to Figure 2-1):

• Keep the distance from the end of the exposed shield to D-Sub as short as possible.
• Ensure the distance from the beginning of the exposed shield to D-Sub is no more than
1.5 inches long.
• Terminate the center conductor by directly connecting it to the D-sub through a crimp pin
without a pigtail.

Figure 2-1 below represents a suggested method for terminating the marker beacon coaxial cable using
M17/128-RG400 terminated into a 78 Pin high density D-Sub connector. Refer to Table 2-1 for Crimp
Tool, Pin, and Crimp Tool Insert part numbers.

Figure 2-1. GMA Marker Beacon Coaxial Cable D-Sub Termination

Table 2-1. Pin and Crimp Tool Part Numbers

CRIMP TOOL PIN CRIMP TOOL INSERT
Garmin Part Number
DANIELS MANUFACTURING CORP K42
336-00021-00
DMC M22520/2-01 GAGE
AFM8 CRIMPING TOOL Garmin Part Number
K774
336-00044-00

GMA 347 Installation Manual Page 2-7

190-00325-01 Revision F
2.7 Installation Approval Considerations for Pressurized Aircraft
Antenna and cable installations on pressurized cabin aircraft require FAA approved installation design
and engineering substantiation data whenever such installations incorporate alteration (penetration) of the
cabin pressure vessel by connector holes and/or mounting arrangements.

For needed engineering support pertaining to the design and approval of such pressurized aircraft antenna
installations, it is recommended that the installer proceed according to any of the following listed
alternatives:

1. Obtain approved antenna installation design data from the aircraft manufacturer.

2. Obtain an FAA approved Supplemental Type Certificate (STC) pertaining to and valid for the
subject antenna installation.

3. Contact the FAA Aircraft Certification Office in the appropriate Region and request identification
of FAA Designated Engineering Representatives (DERs) who are authorized to prepare and
approve the required antenna installation engineering data.

4. Obtain FAA Advisory Circular AC-183C and select (and contact) a DER from the roster of
individuals listed in that document.

5. Contact an aviation industry organization such as the Aircraft Electronics Association and request
their assistance.

2.8 Electrical Noise

Because the audio panel is a point in the aircraft where signals from many pieces of equipment are
brought together, take care to minimize effects from coupled interference and ground loops.

Coupled interference can creep into audio system interconnecting cables when they are routed near large
AC electric fields, AC voltage sources and pulse equipment (strobes, spark plugs, magnetos, EL displays,
CRTs, etc). Interference can also couple into audio system interconnecting cables by magnetic induction
when they are routed near large AC current-carrying conductors or switched DC equipment (heaters,
solenoids, fans, autopilot servos, etc).

Ground loops are created when there is more than one path in which return currents flow or when signal
returns share the same path as large currents from other equipment. These large currents create
differences in ground potential between the various equipment operating in the aircraft. These differences
in potential can produce an additive effect on audio panel input signals.

The audio panel may “see” the desired input signal plus an unwanted component injected by ground
differentials, a common cause of alternator-related noise. This is the main reason why all audio jacks
should be isolated from ground. Terminating audio shields just at one end eliminates another potential
ground loop injection point.

Single-point grounding cannot be overstressed for the various avionics producing and processing audio
signals. Single-point, in this context, means that the various pieces of equipment share a single common
ground connection back to the airframe. Good aircraft electrical/charging system ground bonding is also
important.

The wiring diagrams and accompanying notes in this manual should be followed closely to minimize
noise effects.

Page 2-8 GMA 347 Installation Manual

Revision F 190-00325-01
2.9 GMA 347 Mounting

The GMA 347 mounting surface must be capable of providing structural support and electrical bond to
the aircraft to minimize radiated EMI and provide protection from High-Intensity Radiation Fields
(HIRF).

The GMA 347 is mounted using its own system rack. Figure 2-2 shows the GMA 347 unit rack.

1 Slide the unit into the rack until the front lobe of the unit touches the rack.
2 Insert a 3/32 inch hex wrench into the access hole on the faceplate.
3 Turn the hex wrench clockwise until the unit is secured in the rack. Continue turning until
tight. Do not over-tighten the screw.
4 To remove the unit from the rack, turn the hex wrench counterclockwise until it disengages
from the rack.

NOTE
Rear support is recommended to ensure a sturdy mount.

Figure 2-2. GMA 347 Unit Rack (115-00427-00)

GMA 347 Installation Manual Page 2-9

190-00325-01 Revision F
 This page intentionally left blank

Page 2-10 GMA 347 Installation Manual

Revision F 190-00325-01
3 INSTALLATION PROCEDURE
3.1 Unpacking Unit
Carefully unpack the equipment and make a visual inspection of the unit for evidence of damage incurred
during shipment. If the unit is damaged, notify the carrier and file a claim. To justify a claim, save the
original shipping container and all packing materials. Do not return the unit to Garmin until the carrier
has authorized the claim.

Retain the original shipping containers for storage. If the original containers are not available, a separate
cardboard container should be prepared that is large enough to accommodate sufficient packing material
to prevent movement of the item within the container.

3.2 Marker Beacon Antenna Installation

Install the marker beacon antenna according to the antenna manufacturer’s instructions and FAA
Advisory Circulars AC 43.13-1B and AC 43.13-2B Chapters 2 and 3, as applicable.

3.3 Marker Beacon Antenna Cable Connectors

The marker beacon antenna cable requires a BNC or similar coax connector on the antenna end. Follow
connector manufacturer instructions for assembly of the antenna connector.

3.4 Electrical Connections

All electrical connections to the GMA 347, including the marker beacon antenna and shield ground, are
made through two 78-pin D-subminiature connectors (see Figure 4-1). Tables in Section 4 define the
electrical characteristics of all input and output signals. Required connector and associated hardware are
supplied in the connector kit (P/N 011-00813-01). See figures in Appendix C for interconnect wiring
diagrams.

CAUTION
Check wiring connections for errors before inserting the GMA 347 into
the rack. Incorrect wiring could cause internal component damage.

Table 3-1. Pin Contact Part Numbers (Hi Density)

78 pin D-Subminiature Connectors (P3471, 3472)
Manufacturer
16 AWG 18-20 AWG 22-28 AWG
(Power Only)
Garmin P/N 336-00044-01 336-00044-00 336-00021-00
Military P/N N/A N/A M39029/58-360
AMP N/A N/A 204370-2
Positronic N/A N/A MC8522D
ITT Cannon N/A N/A 030-2042-000

GMA 347 Installation Manual Page 3-1

190-00325-01 Revision F
 Table 3-2. Recommended Crimp Tools (Hi Density)
18-20 AWG 22-28 AWG
Manufacturer Hand
Positioner Insertion/ Positioner Insertion/
Crimping Tool
Extraction Tool Extraction
(Note 2) Tool
Military P/N M22520/2-01 N/A M81969/1-04 M22520/2-09 M81969/1-04
Positronic 9507 9502-11 M81969/1-04 9502-4 M81969/1-04
ITT Cannon 995-0001-584 N/A N/A M22520/2-09 274-7048-000
AMP 601966-1 N/A 91067-1 601966-6 91067-1
Daniels AFM8 K774 M81969/1-04 K42 M81969/1-04
Astro 615717 N/A M81969/1-04 615725 M81969/1-04

NOTES
1. Non-Garmin part numbers shown are not maintained by Garmin and
consequently are subject to change without notice.
2. Extracting the #16, #18 and #20 contact requires that the expanded wire
barrel be cut off from the contact. It may also be necessary to push the
pin out from the face of the connector when using an extractor due to the
absence of the wire. A new contact must be used when reassembling the
connector.
3. For applications using 16 AWG wire, contact Garmin for information
regarding connector crimp positioner tooling.

Page 3-2 GMA 347 Installation Manual

Revision F 190-00325-01
3.5 Backshell Assembly and D -Subminiature Connectors
The GMA 347 connector kit (011-00813-01) includes two Garmin backshell assemblies. Backshell
connectors give the installer the ability to terminate shield grounds at the backshell housing using the
Shield Block ground kit. The term ‘D-Sub’ (D-Subminiature) connectors have a letter "D" physical
shape. D-Sub refers only to the polarized shell that holds the contacts (pins or sockets) in place. Table
3-3 lists Garmin part numbers for the GMA 347 D-Sub Connectors and the Backshell Assembly.

Table 3-3. Backshell Assembly (011-00812-00)

Figure Ref Description Garmin P/N

1 Cast Housing (From Garmin Backshell kit.) 125-00085-00
2 Shield block 117-00147-xx
3 Screw, 4-40 x.250, FLHP100°, SS/P, Nylon. 211-63234-08
4 Multiple Conductor Shielded Cable As Required
(See Interconnect Diagrams, Appendix C)
5 Shield Termination As Required
6 Braid, Flat (19 – 20 AWG equivalent, tinned plated copper As Required
strands 36 AWG, Circular Mil Area 1000 – 1300)
7 Shrink Tubing As Required
8 Pins 336-00021-00
9 Ring terminal, #8, insulated, 18-22 AWG, 14-16 AWG, 10-12 MS25036-149,
AWG MS25036-153,
MS25036-156
10 Screw, PHP, 8-32x.312", Stainless or Cad Plated Steel MS51957-42,
MS35206-242
11 Split Washer, #8, (.045" compressed thickness) Stainless or MS35338-137,
Cad-plated steel MS35338-42
12 Flat Washer, #8, .032" thick, .174"ID, .375" OD, Stainless or NAS1149CN832R,
Cad Plated Steel NAS1149FN832P
13 Silicon Fusion Tape 249-00114-00
14 Strain Relief 115-00499-xx
15 Screw,4-40x.375,PHP,SS/P,w/Nylon 211-60234-10
16 Lid 115-00500-xx
17 Screw,4-40x.187,FLHP100,SS/P,w/Nylon 211-63234-06

GMA 347 Installation Manual Page 3-3

190-00325-01 Revision F
3.5.1 Shield Block Assembly Procedure
The parts for the connector and backshell assembly, GMA 347 installations, are listed in Table 3-3 and
shown in Figure 3-1.

16 15
17
14

13
1
2

3 7
6 5
9
4
12
11
10
Figure 3-1. Shield Block Install onto Backshell Connector Assembly

Table 3-4. Shield Block Components

Backshell Assembly Shield Block

Garmin P/N Garmin P/N
011-00950-04
011-01169-01
(78 Pin High Density)

Page 3-4 GMA 347 Installation Manual

Revision F 190-00325-01
1. Attach the Shield Block(s) (2) to the backshell (1) by inserting the flathead screws (3) through the
holes on the Shield Block and threading into the tapped holes on the backshell (1). (See Figure 3-1).
The appropriate number of Shield Block kits is included in the GMA 347 connector kit.

Table 3-5. Shielded Cable Preparation

Float Float Ideal Window Window Ideal

Min Max Float Min Max Window
1.5” 2.5” 2.0” 3.0” 5.5” 4.5”

Figure 3-2. Shielded Cable Preparation

2. At one end of a shielded cable (4) measure back a distance between “Window Min” to “Window
Max” (Table 3-5) and cut a window (max size 0.35”) in the jacket to expose the shield. (See Figure
3-2). Use caution when cutting the jacket to avoid damaging the individual braids of the shield.
When dealing with a densely populated connector with many cables it may prove beneficial to
stagger the windows throughout the “Window Min” to “Window Max” range. If staggering is not
needed the “Ideal Window” length is recommended.

Tools needed to Accomplish the Window Cut:

• Coaxial Cable Stripper
• Thermal Stripper
• Sharp Razor Blade

3. Connect a Flat Braid (6) to the shield exposed through the window of the prepared cable assembly
(4). The Flat Braid goes out the front of the termination towards the connector. Do not allow wires
to exit the rear of the termination and loop back towards the connector. (See Figure 3-2). Make this
connection using an approved shield termination technique. Refer to FAA Advisory Circular AC
43.13 as a reference for termination techniques.

Preferred Method, Solder Sleeves:

Slide a solder sleeve (5) onto the prepared cable assembly (4) and connect the Flat Braid (6) to the shield
using a heat gun approved for use with solder sleeves. It may be easier to use a solder sleeve with a pre-
installed Flat Braid versus having to cut a length of Flat Braid to be used. The chosen size of solder
sleeve must accommodate both the number of conductors present in the cable and the Flat Braid (6) to be
attached.

GMA 347 Installation Manual Page 3-5

190-00325-01 Revision F
 NOTE
Solder Sleeves with pre-installed Flat Braid: A preferred solder sleeve
is the Raychem S03 Series with the thermochromic temperature
indicator. These solder sleeves come with a pre-installed braid and
effectively take the place of items 5 and 6. For detailed instructions on
product use, refer to Raychem installation procedure RCPS 100-70.

Raychem Recommended Heating Tools:

• HL1802E
• AA-400 Super Heater
• CV-1981
• MiniRay
• IR-1759

Individual Solder Sleeves and Flat Braid

Solder Sleeves:
Reference the following MIL-Specs for general solder sleeves:
(M83519/1-1, M83519/1-2, M83519/1-3, M83519/1-4, M83519/1-5).

Flat Braid:
If the preferred Raychem sleeves are not being used, the individual flat braid selected should conform to
ASTMB33 for tinned copper and be made up of 36 AWG strands to form an approximately 19-20 AWG
equivalent flat braid. A circular mil area range of 1000 to 1300 is required. The number of individual
strands in each braid bundle is not specified.

NOTE
Flat Braid as opposed to insulated wire is specified in order to insure
continuing airworthiness by allowing for visual inspection of the
conductor.

Secondary Method, Heat Shrink instead of Solder Sleeves:

Solder a Flat Braid (6) to the shield exposed through the window of the prepared cable assembly (4).
Ensure a solid electrical connection through the use of acceptable soldering practices. Use care to avoid
applying excessive heat that burns through the insulation of the center conductors and shorts the shield to
the signal wire. Slide a minimum 0.75” of Teflon heat shrinkable tubing (5) onto the prepared wire
assembly and shrink using a heat gun. The chosen size of heat shrinkage tubing must accommodate both
the number of conductors present in the cable and the Flat Braid (6) to be attached.

Page 3-6 GMA 347 Installation Manual

Revision F 190-00325-01
4. At the same end of the shielded cable (4) and ahead of the previous shield termination, strip back
“Float Min” to “Float Max” (Table 3-5) length of jacket and shield to expose the insulated center
conductors. (See Figure 3-2). It may be best to build the “Ideal Float” length optimally.

Preferred Method:
The jacket and shield should be cut off at the same point so no shield is exposed. Slide 0.75” minimum of
Teflon heat shrinkable tubing (7) onto the cable and use a heat gun to shrink the tubing. The chosen size
of heat shrinkage tubing must accommodate the number of conductors present in the cable

Secondary Method:
Leave a max 0.35” of shield extending past the jacket. Fold this 0.35” of shield back over the jacket.
Slide a solder sleeve (7) over the end of the cable and use a heat gun approved for solder sleeves to secure
the connection. The chosen size of solder sleeve must accommodate the number of conductors present in
the cable.

5. Strip back 1/8” of insulation and crimp a pin (8) to each of the conductors in the shielded cable.

6. Insert newly crimped pins and wires into the appropriate connector housing location as specified by
the installation wiring diagrams.

7. Cut the Flat Braid (6) to a length with the addition of a ring terminal that will reach one of the tapped
holes of the Shield Block (2). (See Figure 3-1). An appropriate amount of excess length without
looping should be given to the Flat Braid (6) to allow it to move freely with the wire bundle. Note
that the maximum distance from the backshell allowed for the window splice should keep the Flat
Braid (6) to a worst case length of approximately 4”.

8. Guidelines for terminating the newly cutoff Flat Braid(s) (item 6) with insulated ring terminals (9):

• Each tapped hole on the Shield Block (2) may accommodate only two ring terminals (9).
• It is preferred that only two Flat Braids (6) be terminated per ring terminal. Two Flat Braids per
ring terminal will necessitate the use of a Ring terminal, #8, insulated, 14-16 AWG
(MS25036-153).
• If only a single Flat Braid is left or if only a single Flat Braid is need for this connector, a Ring
terminal, #8, insulated, 18-22 AWG (MS25036-149) can accommodate this single Flat Braid.
• If more braids exist for this connector than two per ring terminal, it is permissible to terminate
three braids per ring terminal. This will necessitate the use of a Ring terminal, #8, insulated,
10-12 AWG (MS25036-156).
• In rare situations where more braids need to be terminated for this connector than three per ring
terminal it is allowable to daisy chain a maximum of two shields together before coming to the
ring terminal. (See Figure 3-3).

GMA 347 Installation Manual Page 3-7

190-00325-01 Revision F
 WINDOW MAX.
WINDOW MIN.
6 5

6 5
FLOAT MIN. TO FLOAT MAX. 7

0.75 INCHES MIN. 0.35 INCHES MAX.

0.17 INCHES
FOR REF. ONLY
SEE FIGURE 13-3

Figure 3-3: Daisy Chain Method for Shield Termination

9. Repeat steps 2 through 8 as needed for the remaining shielded cables.

10. Terminate the ring terminals to the Shield Block (2) by placing items on the Pan Head Screw (10) in
the following order: Split Washer (11), Flat Washer (12), first Ring Terminal, second Ring Terminal
if needed, before finally inserting the screw into the tapped holes on the Shield Block. Do not violate
the guidelines presented in Step 8 regarding ring terminals.

11. It is recommended to wrap the cable bundle with Silicone Fusion Tape (13) (GPN: 249-00114-00 or a
similar version) at the point where the backshell strain relief and cast housing will contact the cable
bundle. Note: Choosing to use this tape is at the discretion of the installer.

12. Place the smooth side of the backshell strain relief (14) across the cable bundle and secure using the
three screws (15). Warning: Placing the grooved side of the strain relief across the cable bundle may
risk damage to wires.

13. Attach the cover (16) to the backshell (1) using two screws (17).

7
9

6
Figure 3-4: Parallel Shield Termination
Page 3-8 GMA 347 Installation Manual
Revision F 190-00325-01
3.5.2 Configuration Module Installation
Table 3-6 lists part numbers for the Configuration Module Kit.

Table 3-6. Configuration Module Kit – 011-00979-00

Item Description Garmin P/N

Configuration Module PCB Board Assembly w/EEPROM 012-00605-00
Cable 4-Conductor Harness 325-00122-00
Crimp Pins #22 AWG (HD) 336-00021-00
Spacer Spacer, Config Module 213-00043-00

GMA 347 Installation Manual Page 3-9

190-00325-01 Revision F
3.5.3 Configuration Module Assembly Procedure

Table 3-7. Configuration Module Wire Color Reference Chart

Color Function J3472 Pin

Black Ground 1
Red Vcc 21
Yellow Data 40
White Clock 60

1. Crimp pins (4) onto each wire of the four-conductor wire harness (3). Strip 1/8” of insulation
from each wire prior to crimping.
2. Insert newly crimped pins and wires (3, 4) into the appropriate connector housing (5) location
shown in the figure below.
3. Apply the spacer (2) by wrapping it around the PCB Board (1) making sure to insert the plastic
connector mounted on the board into the hole provided in the spacer.
4. Plug the four-conductor wire harness (3) into the connector on the PCB Board (1).
5. Insert into the backshell (6) recess, PCB Board (1) with pad (2) in position.
6. Attach cover (7) to backshell (6) using screws (8).

Figure 3-5. Configuration Module Installation

Page 3-10 GMA 347 Installation Manual

Revision F 190-00325-01
3.6 Circuit Breaker Placard
Install a Circuit Breaker Placard labeled Audio Panel, Audio Panel 1 or Audio Panel 2 as appropriate as
indicated in FAA Advisory Circular AC 43.13-2B, Paragraph 207f(4).

3.7 GMA 347 Unit Installation

CAUTION
Do not use excessive force when inserting the GMA 347 into the rack.
This may damage the connectors, unit, and/or unit rack. If heavy
resistance is felt during installation, stop! Remove the GMA 347 and
identify the source of resistance.

For final installation and assembly, refer to the outline and installation drawings shown in Appendix B of
this manual.

1. Assemble the backshell as described in Section 3.5.

2. Connect both backshells to the rear plate using the screws provided in the connector kit.
3. Mount the unit rack to a suitable mounting location on the panel using the provided nutplates.
4. Assemble the rear plate into the GMA 347 unit rack.
5. Insert the GMA 347 into the rack, noting proper orientation as shown on the installation
drawing in Appendix B.
6. Lock the GMA 347 in place using a 3/32 hex wrench.

3.8 Post Installation Configuration

CAUTION
Check wiring connections for errors before inserting the GMA 347 into
the tray. Incorrect wiring could cause internal component damage.

For GMA 347 system configuration refer to Table 3-8. Refer to Figure 4-3 for GMA 347
configuration upload connections.
Table 3-8. GMA 347 System Configuration

Garmin Product GMA 347 Configuration Tool

GMA 347, GMA 347H, GMA 347 2ADF,
Used for:
GMA 347 White LED
Program Archive 006-A0115-00
GMA Configuration Tool Manual 005-00155-99
File Name GMA_CONFIG.EXE
GMA_CONFIG.EXE version at time of this
document 2.04

GMA 347 Installation Manual Page 3-11

190-00325-01 Revision F
3.8.1 Volume Configuration

NOTE
For best results, adjust the signal level for the audio source as high as practical without
overdriving the audio panel inputs. This will result in the best overall performance and a
good signal to noise ratio.

When the audio level can be controlled at the audio source and the audio panel has an input gain control
for the audio source, perform the following procedure:

1. Adjust the source audio level to the minimum and the audio panel input gain control to the
minimum.
2. Adjust the user gain controls on the audio panel for normal operation.
3. Increase the audio source level until the desired audio level is reached or the audio source is
close to the maximum specified input level for the audio panel input.

If the audio from the audio source is not loud enough, increase the audio panel input gain until the desired
audio level is reached. Repeat this setup for each audio source and audio panel input with adjustable
gains.

If the audio source does not have adjustable gain then adjust the gain for the audio panel input until the
desired audio level is reached.

If the audio panel input does not have adjustable gain then adjust the audio source gain until the desired
audio level is reached.

Page 3-12 GMA 347 Installation Manual

Revision F 190-00325-01
3.9 Post Installation Checkout
Except for marker beacon operation, an in-aircraft checkout may be performed in the aircraft on the ramp
with a known good microphone, headset, speaker and avionics receivers.

For testing the marker beacon, use a ramp tester that transmits a 75 MHz marker beacon test signal.

For installation checkout procedures refer to the GMA 347 Pilot’s Guide (190-00325-00) for GMA 347
operation. Verify that every function of the GMA 347 operates correctly.

NOTE
In the following procedural steps outlined below, allow for variations in
configuration settings for the particular unit under test.

3.9.2 Lamp Test

Apply power to the unit by rotating the Pilot’s intercom volume knob clockwise out of the detent.

During power-up, the unit undergoes a self-test, illuminating all panel annunciator lights for
approximately two seconds (between 1/2 and 2 seconds).

Confirm the operation of the GMA 347 internal LED annunciators and marker beacon LED’s. Cover the
photocell with a finger and observe that the LED annunciators dim automatically. Check the front panel
key backlighting and dimming function. Key brightness is controlled with the aircraft radio lights
dimming bus.

3.9.3 Failsafe Operation Check

1. Turn the unit off by rotating the Pilot’s intercom volume knob counter clockwise.
2. Check the failsafe operation by exercising the COM 1 microphone, microphone key and audio
over the headphones. A stereo headset connected to the Pilot headphone jack will provide audio
in the left earphone only.
3. Turn the unit back on to continue testing.

3.9.4 Transceiver Operational Check

1. Perform a ramp test radio check by exercising the installed transceivers, microphone, microphone
key, and audio over the headphones and speaker.
2. Verify that communications are loud and clear and PTT operation is correct.

NOTE
Split COM performance varies significantly across installations and is
affected by both the distance between the antennas and the separation of
the tuned frequencies.

3. In appropriate installations, check for Pilot/Copilot microphone operation when using the Split
COM (COM 1/2 key) function.

GMA 347 Installation Manual Page 3-13

190-00325-01 Revision F
3.9.5 Intercom System (ICS) Check

NOTE
If a monaural headset is plugged into any stereo phone jack position, no
damage will occur to the GMA 347. In the case of plugging a monaural
headset into any passenger position, any stereo listener will lose one
channel when another passenger plugs in a monaural headset.

1. Set the intercom to the ALL mode (Pilot and Copilot LED’s off.)
2. Plug in headsets at each ICS position.
3. Adjust squelch and volume for each position and verify that the ICS is working properly.
4. Check Pilot and Copilot ICS positions for isolation and proper operation of volume and squelch
controls.
5. Press and hold the SPKR key for two seconds. Verify that the SPKR key annunciator flashes,
indicating the PA mode, and that microphone audio is heard over the speaker.

3.9.6 Aircraft Receivers Check

1. Select the audio source for each avionics unit installed in the aircraft and check for audio over the
headsets.
2. Check for Pilot/Copilot audio isolation when pressing the Split COM (COM 1/2) key.
3. Press the SPKR key and verify that any selected audio is heard over the speaker.

3.9.7 Clearance Recording Check

1. Allow COM 1 receiver to operate for at least two and one half (2.5) minutes of active operation.
2. Press the PLAY key once to play back the latest recorded memory block of COM 1 audio.
3. Press the PLAY key again to play the previous memory block of COM 1 audio. Continue
stepping backward into the memory blocks until listening to the first block of audio. A total of
2.5 minutes of audio is recorded.
4. Verify that after playing back the full 2.5 minutes of stored audio, that the playback system audio
stops.

3.9.8 Music System Check

1. Set the intercom to the ALL mode (Pilot and Copilot LED’s off).
2. Connect a stereo audio source to MUSIC 1. Verify that stereo audio is heard over the Pilot and
Copilot headset positions.
3. Tune a station on COM 1 and verify that the sound is muted by active COM 1 audio (break
squelch on COM 1 if necessary).
4. Connect a stereo music source to MUSIC 2. Verify that stereo audio is heard in the passenger
headsets.

Page 3-14 GMA 347 Installation Manual

Revision F 190-00325-01
3.9.9 Flight Check

CAUTION
Be sure to check all aircraft control movements before flight is attempted
to insure that the wiring harness does not touch any moving part. Verify
proper operation of the marker beacon during a flight test under VFR
conditions.

Perform a flight test after installing the unit to ensure satisfactory performance of the audio and marker
beacon receiver functions. Verify proper operation of the marker lamps and marker audio, including the
marker audio mute function. Check proper operation of the sensitivity selection, using the SENS key, by
flying towards the outer marker (OM) position initially using HI sensitivity. When the OM audio is just
barely audible in the headset, switching to LO sensitivity should reduce or eliminate the audio.

This completes the in-aircraft post installation checkout.

GMA 347 Installation Manual Page 3-15

190-00325-01 Revision F
 This page intentionally left blank

Page 3-16 GMA 347 Installation Manual

Revision F 190-00325-01
4 SYSTEM INTERCONNECTS

NOTE
When installations that have a Garmin GMA 340 audio panel are being
upgraded to a GMA 347, refer to figure C-5 in Appendix C for a pin-to-
pin comparison of the two units.

4.1 Connector Description

The GMA 347 has two 78-pin connectors located at the rear of the unit designated P3471 and P3472.
P3471 and P3472 are clearly marked on the back of the rack. P3471 and P3472 pins are configured as
shown in the following illustration:

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78

21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59
40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39

60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Figure 4-1. Backshell Rear Connector Plate

60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78

40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59

21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Figure 4-2. Rear Connectors J3471 and J3472, Viewed From Back of Unit

4.2 Connectors J3471 and J3472

J3471 and J3472 pin assignments are given in Tables 4-1 and 4-2.

Following the pin assignment table, additional tables group pin connections by function.

An asterisk (*) following a signal name denotes that the signal is an Active Low. Active Low inputs
require a ground to activate. Active Low outputs sink current to ground when active.

GMA 347 Installation Manual Page 4-1

190-00325-01 Revision F
 Table 4-1. J3471 Pin Assignments
Pin Pin Name I/O
1 FAIL SAFE WARN AUDIO IN In
2 RESERVED --
3 TEL RINGER AUDIO IN HI In
4 TEL RINGER AUDIO IN LO In
5 RESERVED --
6 ON-SIDE NAV AUDIO IN HI In
7 ON-SIDE COM AUDIO IN HI In
8 ON-SIDE COM AUDIO LO I/O
9 PILOT HEADSET AUDIO OUT LEFT Out
10 PILOT HEADSET AUDIO OUT RIGHT Out
11 PILOT HEADSET AUDIO OUT LO Out
12 CROSS-SIDE COM AUDIO IN HI In
13 CROSS-SIDE COM AUDIO LO I/O
14 CROSS-SIDE NAV AUDIO IN HI In
15 DME AUDIO IN HI In
16 DME AUDIO IN LO In
17 MUSIC IN 1 LEFT In
18 MUSIC IN 1 RIGHT In
19 UNSWITCHED AUDIO IN 1 HI In
20 UNSWITCHED AUDIO IN 2 HI In
21 RESERVED --
22 RESERVED --
23 TEL MIC AUDIO OUT HI Out
24 PASS ICS KEY* In
25 ON-SIDE NAV AUDIO IN LO In
26 ON-SIDE COM MIC AUDIO OUT HI Out
27 ON-SIDE COM MIC KEY* Out
28 PILOT MIC AUDIO IN HI In
29 PILOT MIC KEY* IN In
30 PILOT MIC IN LO In
31 PILOT ICS KEY* In
32 CROSS-SIDE COM MIC AUDIO OUT HI Out
33 CROSS-SIDE COM MIC KEY* Out
34 CROSS-SIDE NAV AUDIO IN LO In
35 ADF AUDIO IN HI In
36 ADF AUDIO IN LO In
37 MUSIC IN 1 LO In
*Denotes Active Low (Inputs: ground to activate; Outputs: grounded when active).

Page 4-2 GMA 347 Installation Manual

Revision F 190-00325-01
 Table 4-1. J3471 Pin Assignments (Continued)
Pin Pin Name I/O
38 UNSWITCHED AUDIO IN 3 HI In
39 UNSWITCHED AUDIO IN LO In
40 RESERVED --
41 RESERVED --
42 TEL AUDIO IN HI In
43 TEL AUDIO IN LO In
44 PASS 3 MIC AUDIO IN HI In
45 PASS 3 MIC AUDIO IN LO In
46 PASS 1 MIC AUDIO IN HI In
47 PASS 1 MIC AUDIO IN LO In
48 PASS HEADSET AUDIO OUT LO Out
49 COPILOT MIC AUDIO IN HI In
50 COPILOT MIC KEY* IN In
51 COPILOT MIC IN LO In
52 COPILOT ICS KEY* In
53 RESERVED --
54 ALTITUDE WARN AUDIO IN HI In
55 ALTITUDE WARN AUDIO IN LO In
56 MUSIC IN 2 LEFT In
57 MUSIC IN 2 RIGHT In
58 COM 3 AUDIO IN HI In
59 COM 3 AUDIO LO I/O
60 RESERVED --
61 RESERVED --
62 TEL MIC AUDIO OUT LO Out
63 PASS 4 MIC AUDIO IN HI In
64 PASS 4 MIC AUDIO IN LO In
65 PASS 2 MIC AUDIO IN HI In
66 PASS 2 MIC AUDIO IN LO In
67 PASS HEADSET AUDIO OUT LEFT Out
68 PASS HEADSET AUDIO OUT RIGHT Out
69 COPILOT HEADSET AUDIO OUT LEFT Out
70 COPILOT HEADSET AUDIO OUT RIGHT Out
71 COPILOT HEADSET AUDIO OUT LO Out
72 RESERVED --
73 RESERVED --
74 AUX AUDIO IN HI In
75 AUX AUDIO IN LO In
76 MUSIC IN 2 LO In
77 COM 3 MIC AUDIO OUT HI Out
78 COM 3 MIC KEY* Out
*Denotes Active Low (Inputs: ground to activate; Outputs: grounded when active).

GMA 347 Installation Manual Page 4-3

190-00325-01 Revision F
 Table 4-2. J3472 Pin Assignments
Pin Pin Name I/O
1 CONFIG MODULE GROUND --
2 RESERVED --
3 PROGRAM GROUND --
4 RECORDER PLAY* In
5 PROGRAM GROUND --
6 RS-232 OUT 1 Out
7 RS-232 IN 1 In
8 RESERVED --
9 RESERVED --
10 RESERVED --
11 PROGRAM GROUND --
12 RESERVED --
13 RESERVED --
14 POWER GROUND --
15 RESERVED --
16 POWER GROUND --
17 COM SWAP* In
18 PROGRAM GROUND --
19 RESERVED --
20 RESERVED --
21 CONFIG MODULE POWER OUT Out
22 RESERVED --
23 PROGRAM GROUND --
24 RECORDER OFF SELECT* In
25 PROGRAM GROUND --
26 AUX SOURCE SELECT* In
27 RESERVED --
28 RESERVED --
29 RESERVED --
30 AIRCRAFT POWER 2 In
31 RESERVED --
32 AIRCRAFT POWER 2 In
33 RESERVED --
34 MIDDLE MARKER SENSE Out
35 RESERVED --
36 RESERVED --
37 GROUND RETURN --
*Denotes Active Low (Inputs: ground to activate; Outputs: grounded when active).

Page 4-4 GMA 347 Installation Manual

Revision F 190-00325-01
 Table 4-2. J3472 Pin Assignments (Continued)
Pin Pin Name I/O
38 RS-232 OUT 2 Out
39 RS-232 IN 2 In
40 CONFIG MODULE DATA I/O
41 SPEAKER AUDIO OUT LO Out
42 SPEAKER AUDIO OUT HI Out
43 RESERVED --
44 PROGRAM GROUND --
45 RESERVED --
46 PROGRAM GROUND --
47 RESERVED --
48 RESERVED --
49 RESERVED --
50 RESERVED --
51 14 V LIGHTING HI In
52 28 V LIGHTING HI In
53 AIRCRAFT POWER 1 In
54 RESERVED --
55 AIRCRAFT POWER 1 In
56 RESERVED --
57 GROUND RETURN --
58 RESERVED --
59 MARKER ANTENNA LO In
60 CONFIG MODULE CLOCK Out
61 RESERVED --
62 RESERVED --
63 RESERVED --
64 PA MUTE* OUT Out
65 RESERVED --
66 RESERVED --
67 PROGRAM GROUND --
68 RESERVED --
69 POWER GROUND --
70 RESERVED --
71 POWER GROUND --
72 RESERVED --
73 RESERVED --
74 AIRWAY/INNER MARKER EXT LAMP OUT Out
75 MIDDLE MARKER EXT LAMP OUT Out
76 OUTER MARKER EXT LAMP OUT Out
77 RESERVED --
78 MARKER ANTENNA HI In
*Denotes Active Low (Inputs: ground to activate; Outputs: grounded when active).

GMA 347 Installation Manual Page 4-5

190-00325-01 Revision F
4.3 J3472 Connector Pin Assignments
This section covers the pin connections of J3472 only.

4.3.1 Aircraft Power and Lighting

Power Input requirements and Lighting Bus inputs are listed in the following tables. The power-input
pins accept 14/28 Vdc. AIRCRAFT POWER 2 is for connecting to an alternate power source, such as on
aircraft with two electrical buses. Refer to Figure C-1 for power interconnections.

NOTE
The current rating for the rear connector pins is 2 A DC. For installations with an aircraft
power voltage of 14 V DC, both AIRCRAFT POWER 1 pins must be connected to the
power source and two or more AIRCRAFT GROUND pins must be connected to the
return of the power source. If an alternate power source with a nominal voltage of 14 V
DC is used, both AIRCRAFT POWER 2 pins must be connected to the alternate power
source and two AIRCRAFT GROUND pins must be connected to the return of the
alternate power source.

Pin Pin Name Description I/O

53 AIRCRAFT POWER 1 Unit power In
55 AIRCRAFT POWER 1 Unit power In
30 AIRCRAFT POWER 2 Unit power In
32 AIRCRAFT POWER 2 Unit power In
69 POWER GROUND Aircraft ground --
71 POWER GROUND Aircraft ground --
14 POWER GROUND Aircraft ground --
16 POWER GROUND Aircraft ground --

4.3.2 Lighting Bus

The GMA 347 can be configured to track a 28 Vdc or 14 Vdc lighting bus using these inputs. Refer to
Figure C-1 for lighting interconnections.

Pin Pin Name Description I/O

51 14 V LIGHTING HI 14V Backlighting input, 0 to 14 Vdc In
52 28 V LIGHTING HI 28V Backlighting input, 0 to 28 Vdc In

Page 4-6 GMA 347 Installation Manual

Revision F 190-00325-01
4.3.3 RS -232 Serial Input/Output

Pin Pin Name Description I/O

6 RS-232 OUT 1 Output level greater than ±5 Volts Out
7 RS-232 IN 1 Input level up to ±25 Volts In
38 RS-232 OUT 2 Output level greater than ±5 Volts Out
39 RS-232 IN 2 Input with level up to ±25 Volts In

The RS-232 outputs conform to EIA/TIA-232C with an output voltage swing of at least ±5 V when
driving a standard RS-232 load. The RS-232 IN/OUT 1 connections are used to upload configuration
data into the unit. The unit is configured out of the aircraft, before final installation. Refer to
005-00155-99 for configuration instructions.

Figure 4-3. GMA 347 Configuration Upload Connections

GMA 347 Installation Manual Page 4-7

190-00325-01 Revision F
4.3.4 Marker Beacon Functions
Marker Beacon connections are listed in the following table. The antenna input is connected to pins 78
(HI or Center Conductor) and 59 (LO or Shield).

Pin Pin Name Description I/O

34 MIDDLE MARKER SENSE 2.5-8 Vdc into 4.7 kΩ Out
AIRWAY/INNER MARKER EXT
74 MKR I-HI white 2.5-8 Vdc into 56 Ω Out
LAMP OUT
MKR M-HI amber. 2.5-8 Vdc into
75 MIDDLE MARKER EXT LAMP OUT Out
56 Ω
76 OUTER MARKER EXT LAMP OUT MKR O-HI blue. 2.5-8 Vdc into 56 Ω Out
78 MARKER ANTENNA HI Marker antenna input, 50 Ω In
59 MARKER ANTENNA LO Ground reference for pin 78 --

4.3.5 Installation Selection Inputs

The following table shows the Installation Selection Inputs of J3472. The selection inputs have an input
and a program ground. When the input is grounded, the input function is selected.

Pin Pin Name Description I/O

4 RECORDER PLAY* An external pushbutton switch activates In
5 PROGRAM GROUND voice recorder playback. --
17 COM SWAP* When enabled, COM 1 and COM 2 are In
swapped. This is used with a switch tied to
18 PROGRAM GROUND ground for momentary operation. --
24 RECORDER OFF SELECT* When enabled, the voice recorder is In
25 PROGRAM GROUND disabled. --
AUXILIARY SOURCE This input is used for an external switch tied
26 In
SELECT* to ground to control the auxiliary audio.
*Denotes Active Low (Inputs: ground to activate; Outputs: grounded when active).

Page 4-8 GMA 347 Installation Manual

Revision F 190-00325-01
4.3.6 External Configuration Module
The configuration module contains an I2C temp sensor and EEPROM. The configuration module is
located in the connector backshell. The configuration module stores a backup of the unit configuration.

Pin Pin Name Description I/O

1 CONFIGURATION MODULE
Ground --
GROUND
21 CONFIGURATION MODULE
+3.3 Vdc In
POWER
40 CONFIGURATION MODULE DATA Bi-directional data line In/Out
60 CONFIGURATION MODULE CLOCK Signal used to clock data input\output Out

4.3.7 Speaker
The speaker output is capable of driving up to 10 Watts into a 4 Ω or 8 Ω speaker.

Pin Pin Name Description I/O

41 SPEAKER AUDIO OUT LO Ground reference for speaker audio --
42 SPEAKER AUDIO OUT HI Speaker audio output Out

4.3.8 PA MUTE
PA MUTE is an output that when pulled low is active. It is used to trigger the mute function on an
external PA system.

Pin Pin Name Description I/O

64 PA MUTE* OUT Output capable of sinking 500 mA to ground Out
*Denotes Active Low (Inputs: ground to activate; Outputs: grounded when active).

GMA 347 Installation Manual Page 4-9

190-00325-01 Revision F
4.4 J3471 Connector Pin Assignments
This section covers the pin connections of J3471 only.

4.4.1 Mic Audio Inputs and Mic Keys

Pin Pin Name Description I/O

29 PILOT MIC KEY* IN Enables audio into the respective In
50 COPILOT MIC KEY* IN transceiver unit In
28 PILOT MIC AUDIO IN HI In
Pilot Mic audio input and ground reference
30 PILOT MIC IN LO --
49 COPILOT MIC AUDIO IN HI In
Copilot Mic audio input and ground
51 COPILOT MIC IN LO reference --
46 PASS 1 MIC AUDIO IN HI Passenger 1 Mic audio and ground In
47 PASS 1 MIC AUDIO IN LO reference --
65 PASS 2 MIC AUDIO IN HI Passenger 2 Mic audio and ground In
66 PASS 2 MIC AUDIO IN LO reference --
44 PASS 3 MIC AUDIO IN HI Passenger 3 Mic audio and ground In
45 PASS 3 MIC AUDIO IN LO reference --
63 PASS 4 MIC AUDIO IN HI Passenger 4 Mic audio and ground In
64 PASS 4 MIC AUDIO IN LO reference --
*Denotes Active Low (Inputs: ground to activate; Outputs: grounded when active).

4.4.2 ICS Keys

Pin Pin Name Description I/O

31 PILOT ICS KEY* In
52 COPILOT ICS KEY* Enables audio into the intercom system In
24 PASS ICS KEY* In
*Denotes Active Low (Inputs: ground to activate; Outputs: grounded when active).

Page 4-10 GMA 347 Installation Manual

Revision F 190-00325-01
4.4.3 Com Audio and Mic Keys

Pin Pin Name Description I/O

27 ON-SIDE COM MIC KEY* Out
Enables audio into the respective
33 CROSS-SIDE COM MIC KEY* transceiver unit Out
78 COM 3 MIC KEY* Out
7 ON-SIDE COM AUDIO IN HI COM 1 audio input In
26 ON-SIDE COM MIC AUDIO OUT HI COM 1 audio output Out
8 ON-SIDE COM AUDIO LO Ground reference for COM 1 audio --
12 CROSS-SIDE COM AUDIO IN HI COM 2 audio input In
32 CROSS-SIDE COM MIC AUDIO OUT HI COM 2 audio output Out
13 CROSS-SIDE COM AUDIO LO Ground reference for COM 2 audio --
58 COM 3 AUDIO HI COM 3 audio input In
77 COM 3 MIC AUDIO OUT HI COM 3 audio output Out
59 COM 3 AUDIO LO Ground reference for COM 3 audio --
*Denotes Active Low (Inputs: ground to activate; Outputs: grounded when active).

4.4.4 Nav Audio

Pin Pin Name Description I/O

6 ON-SIDE NAV AUDIO IN HI Nav 1 audio input In
25 ON-SIDE NAV AUDIO IN LO Nav 1 ground reference --
14 CROSS-SIDE NAV AUDIO IN HI Nav 2 audio input In
34 CROSS-SIDE NAV AUDIO IN LO Nav 2 ground reference --

4.4.5 Headset Outputs

Pin Pin Name Description I/O

9 PILOT HEADSET AUDIO OUT LEFT Out
10 PILOT HEADSET AUDIO OUT Pilot headset audio output Out
RIGHT
11 PILOT HEADSET AUDIO OUT LO Ground reference for pilot headset --
69 COPILOT HEADSET AUDIO OUT Out
LEFT
70 COPILOT HEADSET AUDIO OUT Copilot headset audio output Out
RIGHT
71 COPILOT HEADSET AUDIO OUT LO Ground reference for copilot --
headset
67 PASS HEADSET AUDIO OUT LEFT Out
Passenger headset audio output
68 PASS HEADSET AUDIO OUT RIGHT Out
Ground reference for passenger
48 PASS HEADSET AUDIO OUT LO --
headset

GMA 347 Installation Manual Page 4-11

190-00325-01 Revision F
4.4.6 Music Inputs

Pin Pin Name Description I/O

17 MUSIC IN 1 LEFT In
Music 1 input
18 MUSIC IN 1 RIGHT In
37 MUSIC IN 1 LO Ground reference for music 1 --
56 MUSIC IN 2 LEFT In
Music 2 input
57 MUSIC IN 2 RIGHT In
76 MUSIC IN 2 LO Ground reference for music 2 --

4.4.7 Unswitched Audio Inputs

Pin Pin Name Description I/O

19 UNSWITCHED AUDIO IN 1 HI Unmuted/unswitched input In
20 UNSWITCHED AUDIO IN 2 HI Unmuted/unswitched input In
38 UNSWITCHED AUDIO IN 3 HI Unmuted/unswitched input In
39 UNSWITCHED AUDIO IN LO Ground reference for unswitched audio --
54 ALTITUDE WARN AUDIO IN HI Unmuted/unswitched input In
55 ALTITUDE WARN AUDIO IN LO Ground reference for altitude warning --

4.4.8 Telephone I/O

Pin Pin Name Description I/O

3 TEL RINGER AUDIO IN HI Ringtone audio input In
Ground reference for telephone ringer
4 TEL RINGER AUDIO IN LO In
audio input
23 TEL MIC AUDIO OUT HI Transmitted telephone audio output Out
62 TEL MIC AUDIO OUT LO Ground reference for telephone Mic audio --
42 TEL AUDIO IN HI Received telephone audio input In
43 TEL AUDIO IN LO Ground reference for telephone input --

Page 4-12 GMA 347 Installation Manual

Revision F 190-00325-01
4.4.9 AUX, DME and ADF Audio

Pin Pin Name Description I/O

74 AUX AUDIO IN HI Extra switched audio input In
75 AUX AUDIO IN LO Ground reference for extra switched audio input --
15 DME AUDIO IN HI Distance measuring equipment audio input In
16 DME AUDIO IN LO Ground reference for DME audio input --
35 ADF AUDIO IN HI Automatic direction finder audio input In
Ground reference for automatic direction finder
36 ADF AUDIO IN LO --
audio input

4.4.10 Failsafe Audio

Pin Pin Name Description I/O

Audio summed to the pilot’s headset left
1 FAIL SAFE WARN AUDIO IN In
when power fails

GMA 347 Installation Manual Page 4-13

190-00325-01 Revision F
 This page intentionally left blank

Page 4-14 GMA 347 Installation Manual

Revision F 190-00325-01
APPENDIX A CERTIFICATION DOCUMENTS
A.1 Airworthiness Approval
Airworthiness approval of the GMA 347 may be acquired by the use of FAA Form 337. The following is
provided as sample wording for Form 337, when replacing an existing audio panel with a Garmin
GMA 347 Audio Panel. Modify appropriately for new installations.

Removed the existing [model] audio panel and replaced with a Garmin GMA 347 Audio Panel
and Marker Beacon, P/N 010-00275-xx in [aircraft location].

The GMA 347 is FAA TSO Approved to TSO-C50c and TSO-C35d Class A. The GMA 347
meets RTCA DO-160D or RTCA DO-160C environmental qualifications for this installation.
See Section 1 of the GMA 347 Installation Manual.

Installed in accordance with the Garmin GMA 347 Installation Manual 190-00325-01, Revision
[ ], and AC 43.13-2, Chapters 2, and 3.

The GMA 347 interfaces with existing aircraft radios per the Installation Manual instructions.
The Installation Manual provides detailed installation instructions and wiring diagrams (Sections
2, 3, and 4 and Appendices B and C).

Power is supplied to the GMA 347 through an existing [AUDIO 5] 5-Amp circuit breaker that
was previously used by the existing audio panel. The net electrical load is unchanged.

Aircraft equipment list, weights and balance amended. Compass compensation checked and
found to conform to applicable regulations.

A.2 Continued Airworthiness

Maintenance of the GMA 347 is “on condition” only. Refer to the GMA 347 Maintenance Manual
(Garmin P/N 190-00325-02). Periodic maintenance of the GMA 347 is not required.

The following sample Instructions for Continued Airworthiness (ICA) provides assistance in preparing
ICA for the Garmin GMA 347 unit installation as part of an FAA Type Certificate (TC) or Supplemental
Type Certificate (STC) project, to comply with 14 CFR §§23.1529 and 25.1529, “Instructions for
Continued Airworthiness”.

Items that may vary by aircraft make and model are shown in braces (“[ ]”) and should be filled in as
appropriate. Some of the checklist items do not apply, in which case they should be marked “N/A” (Not
Applicable).

GMA 347 Installation Manual Page A-1

190-00325-01 Revision F
 Instructions For Continued Airworthiness, Garmin GMA 347 Audio Panel In An
Aircraft [Make And Model]

1. Introduction
[Aircraft that has been altered: Registration (N-) number, Make, Model and Serial Number]

Content, Scope,
Purpose and Arrangement: This document identifies the Instructions for Continued Airworthiness
for a Garmin GMA 347 installed in an [aircraft make and model].
Applicability: Applies to a Garmin GMA 347 installed in an [aircraft make and
model].
Definitions/Abbreviations: None, N/A.
Precautions: None, N/A.
Units of Measurement: None, N/A.
Referenced Publications: Garmin GMA 347 Audio Panel Installation Manual,
P/N 190-00325-01
Garmin GMA 347 Audio Panel Maintenance Manual,
P/N 190-00325-02
Garmin GMA 347 Audio Panel Pilot’s Guide, P/N 190-00325-00
STC/TC # [applicable STC/TC number for the specific aircraft
installation]
Distribution: This document should be a permanent aircraft record.

2. Description of the System

Garmin GMA 347 Audio Panel with interface to external transceivers and [include other
equipment/systems as appropriate]. Refer to Appendix C and Figures C-1 through C-5 of this manual
for interconnect information. Refer to aircraft manufacturer approved interconnect for actual
installation. Marker Beacon antenna installation, removal and replacement should be in accordance
with applicable provisions of AC 43.13-1B and AC 43.13-2B.

3. Control, Operation Information

Refer to the GMA 347 Audio Panel Pilot’s Guide, P/N 190-00325-00.

4. Servicing Information
N/A

5. Maintenance Instructions
Maintenance of the GMA 347 Audio Panel is ‘on condition’ only. Periodic maintenance is not
required. Refer to the GMA 347 Audio Panel Maintenance Manual.

6. Troubleshooting Information
Refer to the GMA 347 Audio Panel Maintenance Manual.

7. Removal and Replacement Information

Refer to Sections 2 and 3 of the GMA 347 Audio Panel Installation Manual. If the unit is removed
and reinstalled, a functional check of the equipment should be conducted.

Page A-2 GMA 347 Installation Manual

Revision F 190-00325-01
 8. Diagrams
Refer to Appendices B and C of the GMA 347 Audio Panel Installation Manual for installation
drawings and interconnect examples.

9. Special Inspection Requirements

N/A

10. Application of Protective Treatments

N/A

11. Data: Relative to Structural Fasteners

GMA 347, antenna and appropriate mounting hardware installation, removal and replacement should
be in accordance with applicable provisions of AC 43.13-1B and AC 43.13-2B.

12. Special Tools

N/A

13. This Section is for Commuter Category Aircraft Only

A. Electrical loads: Refer to Sections 1 and 4 of the GMA 347 Audio Panel Installation Manual.
B. Methods of balancing flight controls: N/A.
C. Identification of primary and secondary structures: N/A.
D. Special repair methods applicable to the airplane: Antenna installation, removal, and replacement
should be in accordance with applicable provisions of AC 43.13-1B and AC 43.13-2B.

14. Overhaul Period

No additional overhaul time limitations.

15. Airworthiness Limitation Section

N/A.

GMA 347 Installation Manual Page A-3

190-00325-01 Revision F
 This page intentionally left blank

Page A-4 GMA 347 Installation Manual

Revision F 190-00325-01
APPENDIX B ASSEMBLY AND INSTALLATION DRAWINGS
1.30 33.0 1.59 40.5

6.29 159.8 6.30 160.0

3.15 80.0

.13 3.2

3.65 92.7

6.39 162.4

7.79 197.8

.35 8.9

.65 16.5

.95 24.1

.66 16.8
1.325 33.66

.437 11.10
.60 15.2

3.925 99.70

5.600 142.24

Figure B-1. GMA 347 Outline Drawing

GMA 347 Installation Manual Page B-1 (Page B-2 blank)
190-00325-01 Revision F
APPENDIX B ASSEMBLY AND INSTALLATION DRAWINGS

PART OF
011-00812-XX

115-00427-00

PART OF
011-00813-XX

011-00812-XX

011-00813-XX

Figure B-2. GMA 347 Connector/Rack Assembly Drawing

GMA 347 Installation Manual Page B-3 (Page B-4 blank)
190-00325-01 Revision F
APPENDIX B ASSEMBLY AND INSTALLATION DRAWINGS

OPTION 1:
STACK CUTOUT (RACK INSTALLED
FROM FRONT OF AIRCRAFT PANEL)

6.30 160.0

OPTION 2:
RADIO CUTOUT (RACK INSTALLED
FROM FRONT OF AIRCRAFT PANEL)

1.33 33.8
.05 1.3

2.78 70.5 2.78 70.5

.75 19.1
6.30 160.0

OPTION 3:
RADIO CUTOUT (RACK INSTALLED
FROM BACK OF AIRCRAFT PANEL ONLY)
MAXIMUM AIRCRAFT PANEL THICKNESS
IS .125 INCH [3.2 mm]
1.25 31.8 NOTES:
.05 1.3 1. DIMENSIONS: INCH [mm]
2. IF THE FRONT LIP OF THE
MOUNTING RACK IS BEHIND
THE SURFACE OF THE AIRCRAFT
2.72 69.0 2.72 69.0 PANEL THE UNIT CONNECTORS
MAY NOT FULLY ENGAGE.
.75 19.1
6.18 157.0
Figure B-3. GMA 347 Recommended Panel Cutout Dimensions
GMA 347 Installation Manual Page B-5 (Page B-6 blank)
190-00325-01 Revision F
APPENDIX C INTERCONNECT DRAWINGS

Figure C-1. GMA 347 Power, Antenna, and Speaker Interconnect Wiring Diagram
GMA 347 Installation Manual Page C-1 (Page C-2 blank)
190-00325-01 Revision F
APPENDIX C INTERCONNECT DRAWINGS

Figure C-2. Mic and Phone Jack Connections, Interconnect Wiring Diagram
GMA 347 Installation Manual Page C-3 (Page C-4 blank)
190-00325-01 Revision F
APPENDIX C INTERCONNECT DRAWINGS

Figure C-3. Transceiver Analog Connections, Interconnect Wiring Diagram

GMA 347 Installation Manual Page C-5 (Page C-6 blank)
190-00325-01 Revision F
APPENDIX C INTERCONNECT DRAWINGS

Figure C-4. GMA 347 Typical Garmin Integrated Flight Deck Digital Interconnect Wiring Diagram
GMA 347 Installation Manual Page C-7 (Page C-8 blank)
190-00325-01 Revision F
APPENDIX C INTERCONNECT DRAWINGS

Figure C-5. Discrete Lines, Interconnect Wiring Diagram

GMA 347 Installation Manual Page C-9 (Page C-10 blank)
190-00325-01 Revision F
APPENDIX C INTERCONNECT DRAWINGS

(Note 7) (Note 7)

This tone may be

disabled via the GMA 347 configuration program.

configuration program.
(Note 8) (Note 8)

configuration program.

Figure C-6. GMA 340 to GMA 347 Comparison

GMA 347 Installation Manual Page C-11 (Page C-12 blank)
190-00325-01 Revision F