PROJECT:- DATE:
BLDG. NAME:- DETAIL NO.
CLIENT:- NODE NO.
LOCATION:- FRAME NO.
DESIGN CODE: IS 800: 2007-LSM REVISION NO.
a1/d1
ANCHOR BOLT AND BASE PLATE DESIGN (FIXED BASE) ###
###
MATERIAL PROPERTIES ###
###
Concrete : ###
Grade of concrete = M30 30.0 MPa ###
Maximum Bearing Pressure = (0.6 FCK) 18.00 MPa IS 800:2007; Cl. 7.4.1 ###
###
Steel Section : ###
Yield Sress fy = 240 MPa ###
Ultimate Stress fu = 410 MPa ###
###
Anchor Bolts : Grade 5.8 ###
Ultimate Tensile Stress of Bolt fub = 500 MPa IS 1367 (Part 3) : 2002, Table 3 ###
Yeild Stress of Bolt fyb = 400 MPa IS 1367 (Part 3) : 2002, Table 3 ###
Total number of Anchor bolt N = 8 NOS. ###
###
COLUMN SECTION DETAILS ###
Outer Diameter 323.9 ###
Side of Inscribed Squar dw = 220 mm ###
Flange Thickness tf = 6.3 mm ###
###
BASE PLATE DETAILS ###
Assume Dimentions ###
Length of Base Plate, L = 600 mm ###
Width of Base Plate, B = 600 mm ###
Cantilever along Length, a or c = 190 mm ###
Cantilever along Width, b or c = 190 mm ###
Thickness of baseplate ts = 16 mm ###
###
CONNECTION DETAILS ###
Assume ###
Diameter of Bolts to be used, db = 20.0 mm ###
Diameter of Hole, dh = (d+6) = 22.0 mm ###
Spacing of Bolts Provided along width g = 50 mm ≥ 2.5*d O.K. ###
Spacing of Bolts Provided along length p = 50 ###
M0DULUR RATIO n = 9.00 ###
###
LOADS FROM STAAD OUTPUT ###
###
FACTOR LOAD COMBINATION VERTICAL SHEAR MOMENT ###
(KN) (KN) (KN-m) ###
571.4 7.911 15.5 ###
-227.0 2.670 6.3 ###
###
###
CHECK FOR BEARING PRESSURE UNDER BASE PLATE ###
AS PER IS 800:2007; Cl. 7.4.3
Area of base Plate, Aeff = 360000 mm2
MAXMIMUM BEARING PRESSURE UNDER BASE PLATE
w = (P / Aeff) + (6 M / B L2)
w= 2.02 N/mm2 < 18 N/mm2
[HENCE SAFE]
IS 800:2007;
MINIMUM BEARING PRESSURE UNDER BASE PLATE fig.9
w = (P / Aeff) - (6 M / B L2)
w= 1.1576 N/mm2
PROJECT:- DATE:
BLDG. NAME:- DETAIL NO.
CLIENT:- NODE NO.
LOCATION:- FRAME NO.
DESIGN CODE: IS 800: 2007-LSM REVISION NO.
a1/d1
ANCHOR BOLT AND BASE PLATE DESIGN (FIXED BASE) ###
###
CHECK FOR THICKNESS OF BASE PLATE FOR VERTICLE PRESSURE (DL+LL)
Eccentricity e = Moment/Axial force f(y)
e= 27.1 mm f'(y)
D/3 = 200.0 mm
Check for e<=D/3 or e>D/3 k1
SINCE e<=D/3 NO TENSION IN THE BASEPLATE THE FOLLOWING PROCUDURE ARE AS FOLLOWS k2
k3
The depth of neutral axis (y), as shown in the diagram, is given by the cubic equation: K1
y3 + K1.y2 + K2.y + K3 = 0 y0
Where K1 = 3 (e-0.5D)
K1 = -818.81 n
K2 = 6 n As (0.5D-c-e)/B ###
K2 = 15502 ###
K3 = K2 (c-D) ###
K3 = -6355641 ###
The equation is y3 + -819 y2 +15501.6 y -6355641=0 ###
Solving the Equation using Newton Raphson Algorithm ###
y= -192.9 mm ###
P (e + y/3 - D/2) ###
T=
(D - c - y/3) ###
Total tension in bolt on one side T= 0.00 Kn ###
Tension per bolt T= 0.00 Kn ###
Tensile stress in Bolt σs = T/As As = area of bolt ###
Tensile stress in Bolt σs = 0.00 Mpa ###
Stress in concrete σs.y ###
σc =
n (D - y - c) ###
Stress in concrete σc = 0.000 Mpa < 18 N/mm2 ###
[HENCE SAFE] ###
###
The thickness of baseplate is determined using the stiffner, which are as follows: ###
The baseplate behaves as a plate supported on three side. The critical point in such a plate ###
is the middle of its free edge (refer book "Design of Metal structure" by "K K Mukhanov") ###
The moment in this section is determined from the equaction:
For exterior panel
2.02 Mpa Maximum bearing pressure due to 0.00
Maximum bearing pressure in the base plate q = σc =
tension in bolt q = σc =
a1 = 150 mm a1 = 150 mm
d1 = 225 mm d1 = 225 mm
a1/d1 = 0.67 a1/d1 =
α3 = 0.082 α3 = 0.082
M1 = α3 q d12 M1 = α3 q d12
M1 = 8412.30 N-mm M1 = 0.00 N-mm
tm = SQRT ((6*Mm*Ymo)/(1.2*fy)) tm = SQRT ((6*Mm*Ymo)/(1.2*fy))
tm = 13.88 mm tm = 0.00 mm
Hence, Provide Thickness of Base Plate ts = 16 SAFE
Pt
CHECK FOR THICKNESS OF BASE PLATE FOR UPLIFT (DL+WL)
CHECK FOR UPLIFT
Spacing of Bolts Provided along width = g= 220 mm Lb= 226
Spacing of Bolts Provided along length = p= 220 mm
Lb = C/C OF Bolt group length Lb = 226 mm
Tension in bolts on one side due to uplift T = Mt + Pt Mt /2
& moment is Lb 2
T = 141.12 KN
Plate moment due to the uplift force in web M= T(p-0.5db)/8 Pt /2
M= 3704353 N-MM
Thickness of Base plate required due to Uplift ts = (6*M*Ymo)/(1.2*fy*B)
ts = 11.89 mm
Hence, Provide Thickness of Base Plate ts = 16 mm SAFE
PROJECT:- DATE:
BLDG. NAME:- DETAIL NO.
CLIENT:- NODE NO.
LOCATION:- FRAME NO.
DESIGN CODE: IS 800: 2007-LSM REVISION NO.
a1/d1
ANCHOR BOLT AND BASE PLATE DESIGN (FIXED BASE) ###
###
CHECK FOR BOLTS SUBJECTED TO COMBINED SHEAR AND TENSION
Gross Area of Bolts (Asb) Asb = 314 mm2
Net Tensile/Shear Stress Area of Bolts (An) An = 245 mm2 Where bf = Width of baseplate
Partial saftey factor for material Ymo = 1.1
Partial saftey factor for bolt Ymb = 1.25
Factored shear force acting on each bolt Vsb = V/N where N = Total Number of Bolts
Vsb = 1.0 Kn
Factored Tensile force acting on each bolt Tb = T/N where N = Number of Bolts on each side
Tb = 35.3 Kn
Nominal tensile capacity of bolt Tnb = Partial saftey factor for material
= 110.27 Kn
= 142.80 Kn
Tnb = 110.27 Kn
Design Tensile capacity of bolt Tdb =
Tdb = 88.22 Kn
Nominal shear capacity of bolt Vnsb = 1
0
= 70.74 Kn
Design shear capacity of bolt Vdsb =
Vdsb = 56.59 Kn
Design shear capacity of bolt Vdb = 56.59 Kn
Design Tensile capacity of bolt Tdb = 88.22 Kn
Factored shear force acting on each bolt Vsb = 0.99 Kn SAFE
Factored Tensile force acting on each bolt Tb = 35.28 Kn SAFE
A Bolt subjected to Combined IS 800:2007; Cl. 10.3.6
Shear & Tension shall satisfy
A Bolt subjected to Combined = 0.16024 < 1 SAFE
Shear & Tension shall satisfy
Grade of Con
Design Bond
CALCULATION OF ANCHOR BOLT LENGTH Characterist
Anchor Length required = T/(π*d*ζbd) IS 456:2000, Cl. 26.2.1
T= Tension per Bolt 35.3 kn
d= Diameter of Bolt
ζbd = Design Bond Strength of Concrete thk
###
###
For M30 Grade of Concrete, Bond Strength ζbd = 1.5 IS 456:2000, Cl. 26.2.1.1 ###
###
###
Anchor Length required = 374 mm ###
###
Stiff. ht at L ht =
stiff
C/S
