q

ICF-C1O3L
SERVICE MANUAL AEP Model
UK Model

SPECIFICATIONS
Frequency range FM : 87.5 — 108 MHz
MW : 531 — 1,602 kHz
LW : 153 -— 281 kHz
Intermediate frequency
FM : 10.7 MHz
AM : 450 kHz
Scan step FM : 0.05* MHz (fixed)
MW : 9 kHz (fixed)
LW: 2 kHz == 7 kHz
* The frequency display is raised or lowered by steps of
0.1 MHz. (Example: Frequency 88.05 MHz is
displayed as “88.0 MHz”.)
Antennas FM: FM wire antenna
MW/LW: Built-in ferrite bar antenna
Speaker Approx. 6.6 cm (2 °/e inches) dia.
Power output 120 mW (at 10% harmonic distortion)
Power requirements 240 V AC, 50 Hz
Dimensions Approx. 115 x 110 x 105 mm (w/h/d)
(4 5/s x 4 5/s x 4 ‘Ya inches) incl. projecting parts and
controls:
Weight Approx. 590 g (1 Ib 5 oz)

Design and specifications are subject to change without notice.

Note
This appliance conforms with EEC Directive 87/308/EEC regarding
interference Suppression.

-FM/MW/LW PLL SYNTHESIZED

CLOCK RADIO
SONY.
ICF-C103L

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK /\ OR DOTTED
LINE WITH MARK /\ ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
 ICF-C103L
SECTION 1
GENERAL This section is extracted
from instruction manual.

|Wevers|i(e) ame)mmOre) alice) (>

(1 (2)13. ALARM RESET/RADIO
[OFF] button
SLEEP/RADIO [ON button
[3] BAND button
TIME SET/TUNE (tuning) + and — buttons
VOL (volume) control (right side)
ia [6] ALARM MODE button
TIMER (count down timer) button
[8] REPEAT ALARM/SLEEP OFF bar
aN
oe [9] Display window -
Speaker
iS ALARM button
ALARM (WAKE UP STATION) button
Preset number 1 — 5 buttons
ENTER/CLOCK button
a
Bae AC power cord
fié| FM wire antenna

Display window
Band indication
FA RADIO Jalarm indication
Display window alarm indication
TIMER indication
PRESET number indication
[6] Time/frequency indication
AM/PM indication

1 Connect the AC power cord to a wail outlet.

Time indication appears
- and flashes in the display
window.

While keeping the ENTER/CLOCK button pressed,

press the TIME SET/TUNE + or — button to set the time.
The + button advances the
hour and minute digits and mr, PRESET
the — button reverses them. mm
Keep pressing the + or — LG Lf.
button to advance or
reverse the digit rapidly.

Release the ENTER/CLOCK button.

The clock starts operating.

Note on the time indication

the
When the radio is on, “:” of the time indication is lit, and when
radio is off, the “:” is flashing.

Radio is on. Radio is off.

rm A ml PRESET
—_

Lf a —

Zero second adjustment

At step 3, release the ENTER/CLOCK button with the time signal.

8
ICF-C103L

atz\o/(om@)ercie-licelamiiiiclaer-l mlb laliare)

a Turn the VOL control a little to get sound.

3 Press the BAND button to select the band.

Each press of the BAND button changes the band in the
ALARM RESET/ following order.
RADIO
akee MW mde

(The display window shows

7 7 war ~PRESET
the last frequency chosen
in each band.) mt) 1, 0

4 Tune in the station you want by pressing the TIME SET/

TUNE + or — button.
The FM tuning interval is set to 0.05 MHz and the AM
tuning interval is set to 9 kHz.
(The FM frequency indication changes every 0.1 MHz.) The
1 Press the SLEEP/RADIO ‘ON; button. LW tuning interval alternates between 2 kHz and 7 kHz.
The band, frequency and the preset number of the station A beep sounds at the band edge.
before the radio was turned off appear in the display
window. After 10 seconds, the indication becomes the
current time.

5 Adjust volume.

10 11

atzlol(om@lel-e-1 (elem (utcleltrclMmeelaliace))

To turn off the radio To check the station you are listening to
Press the ALARM RESET/RADIO.OFF button. Press the + button lightly. The band and frequency appear for 10
seconds.
To improve reception
FM: Extend the FM wire antenna fully to increase the FM
sensitivity. e When you turn on the radio or change the frequency, the display
MW/LW: Since the reception is affected by the position of the shows the band and frequency for 10 seconds, then it shows the
radio, rotate the unit horizontally for optimum reception. current time.
¢ When you tune in the frequency which is not included in the preset
For the customers supplied with an FM antenna coupler stations, the PRESET number in the display shows{J (out).
Pinch the FM wire antenna and the AC power cord together with the
coupler supplied and connect it to a wall FM antenna terminal for
optimum FM reception.

¢ If the EAL RADIO] alarm time comes while listening to the radio, the
FM antenna coupler station chariges to that preset in number 1.
AC power cord--—..

to wall outlet
FM wire
antenna

to FM antenna
terminal

12 13
 a tz(e|(om@)e-lr-ltColam (atm [einliele))
You can preset up to five FM/MW/LW stations (one station for 1 Tune in the MW 1,260 kHz (see “Radio Operation
each number button 1 to 5). (Manual! Tuning)”).

When you use the radio alarm, preset the station you want for the
alarm in preset button 1, as the PRESET 1 station is the wake up
Station.

Press the ENTER/CLOCK button.

The P indication flashes for 10 seconds.

Presetting the Station

Example: To set MW 1,260 kHz in preset button 2

While P is flashing, press the 2 button.

The P indication becomes 2 (the preset number) and the -
beeps sound.
The station is preset.
Though the indication becomes the current time after 10
seconds, the preset number remains.

! ay I m PRESET c%

MY De |

4 Repeat steps 1 to 3 for each stations to be preset.

To change the preset station

Preset a new station in the number of which you want to change the
station. The previous station is canceled.
14. : 15

Radio Operation (Preset Tuning) setting the Alarm

: 7 : You can set the radio and buzzer alarms. The wake up station is
Tuning in a Preset Station that preset in number 1.

y) Press the preset number button of the station. To set the alarm time at 7:00 AM
The band, frequency and preset number appear in the
display window. After 10 seconds, the indication
becomes the current time.
The preset number remains.

To turn off the radio =

Press the RADIO [OFF] button. i os REPEAT ALARM/
| 4 8 SLEEP OFF
To check the station you are listening to
Press the preset number button.
The band and frequency appear for 10 seconds.
Turn off the radio.

While keeping the £:9 RADIO| ALARM button

pressed, set the time by pressing the TIME SET/
TUNE + or ~ button.

Release the £-9 RADIO! ALARM button.

The alarm time is set. The indication becomes the
current time.

16
 SECTION 2
ELECTRICAL ADJUSTMENTS
AM IF ADJUSTMENT
MW/LW Section Adjust for a maximum reading on VTVM.

Seta Note: Receive 531kHz.

MW antenna close to Frequency

the set. Part Display voltmeter
——— (confirmation) 531kHz More than 1.5V
‘| (Standard 1.7V)
30 % amplitude
: 1,602kHz 8.5V
400Hz signal Note: Not use the AM RF signal generator in this adjustment.
Output level: as low as possible
MW TRACKING ADJUSTMENT
Adjust for a maximum reading on VTVM.

1,404kHz 621kHz
FM RF signal

—
Part Display voltmeter

(C.- FM ANT (Receive 281kHz)

terminal (confirmation) 153kHz More than 1.0V
+22.5kHz frequency deviation (Standard 1.1V)
by 400Hz signal Note : Not use the AM signal generator in this adjustment.
Output level: as low as possible
LW TRACKING ADJUSTMENT
Adjust for a maximum reading on VTVM.

cra
FM VCO VOLTAGE ADJUSTMENT

speaker terminal Adjustment Frequency Reading on Digital

Part Display voltmeter

e Repeat the procedures in each adjustment several times,

87.5MHz More than 1.8V
and the tracking adjustments should be fimally the trimmer (Standard 2,2V)

capacitors. . Note: Not use the FM signal generator in this adjustment.

FM TRACKING ADJUSTMENT
Adjustment Location : Adjust for a maximum reading on VTVM.

108MHz 87.5MHz

(MAIN BOARD] —COMPONENT SIDE— [KEY BOARD] —CONDUCTOR SIDE—

a Late ac ote 1 digital voltmeter

IC1
L5
MW VCO
VOLTAGE
Adjustment
FM
~Y) Ld F=~—— 3-1 > TRACKING
FM VCO Adjustment
VOLTAGE eee
©&) Adjustment (S)

MW LW nanan ne
LW VCO MW LW
TRACKING TRACKING TRACKING —————
VOLTAGE TRACKING | Adjustment Adjustment
Adjustment Adjustment Adjustment
 | | ICF-C103L
SECTION 3
PIN DESCRIPTION

© =,oOaxl,= \e)ond~] NO is G) w o1 oO Ke] sad> ~J

Uv

Pin Name Signal Name 1/0

1-10 LCD10-LCD1 LCD10-LCD1

12-14 COM3-COMI1 COM3-COM1

VSS3
oeNin
on
Pin for doubler circuit capacitor connection to develop LCD drive voltage
ean
—~~)
—

— 8 VSS2
Audio signal mute. Active : Low. LOW when MUTE ON.
— PT
—_—_\O VDP MUTE
f-—MUTE—>|
Nocm) CGP BEEP Activates buzzer.

bo <“Ale V power supply input terminal

23 VCOH “ or wn°«)Qu Zz.jen]

4 VCOM FM VCO M VCO input
|]
N
de — VCOL AM VCO boomed >|M VCO input
ayw
Mi

6 VSS1
Ny~] EO}
PLL error output pin
NOo
¢)

Detects power supply line status.

No\O Q tr tr Power supply line OFF : Low

Power supply line ON : High

we© to
sd
Crystal oscillator connection pin
~
Pin for regulator circuit capacitor connection to attain stable drive voltage
oy)to
— VSS4
of the oscillator |
AC/DC — AC/DC sellect input AC:High DC: Low
| Se
WwW
Go ALARM OUT
>|
>)
> me
wir1m] TV OUT
PAO BATT/BAND 1 1/O BATTERY CHECK input, BAND output FM:Low MW/LW: High
PB3 LIGHT
PB2 POWER 3 =)
=)S Noa.
a. sS ~3
oSopmae
punt

|
Oo
Goa}
G
2
GI} PB1 INITIALIZE oe Y IN control output
Cc
‘a
f. PBO BAND 2 BAND output FM/MW:Low LW: High
f

f — -44 PC3-PCO KEY SOURCE Conducts Key Scan

45-48 K3-KO KEY RETURN Key Return input
49, 50 Z, ©
51-56 LCD16-LCD11 LCD16-LCD11 a Ct) o¥ -

7)| o|
rt.
~]
ICF-C103L
SECTION 4
DIAGRAMS

4-1. SEMICONDUCTOR LEAD LAYOUTS 4-2. PRINTED WIRING BOARDS

CXA1019S 2SC2001-LK 1$$133

-1OE2

cathode

@ Semiconductor Location

Location
(Top view)

anode. D-4 TIME SET

KV1560 S101 0: / TUNING
uPD1724GB-589-1A7 MA152WK D-2 ALARM RESET SLEEP/
D-3 /RADIO OFF RADIO. ON

NTT
D-3
GL3EG8
C-3
—— 28 Os
3
a

AT
C-8
long short B-8
182835 Crt [MAIN BOARD]

NTT
1S
1S2836 C-8
Onode cathode. D-6 ALARM —{8
8UZZeR]
D-6
I

D-6
MARKING SIDE VIEW
D-6

2SA1162-G C-3
2SC1623-L5L6 By ee
2SC2059K-N
2$C2223-F13
2SC2223-F14
jens
l

pO8 94,
2SD596DV345

ANODE. |
CATHODE

2SK238-K16
EES sai th
|-644-050-

|l!

1 Drain
2. Gate
Lek
otok:
Rolo
Reloleletetol
neo?
pe
ES
ees
Eee
Es.
Heeb
Gon
etss

3. Source

Note:
@ oO——: parts extracted from the component side.
 ICF-C103L
4-3. SCHEMATIC DIAGRAMS

1 2 S 4 #5 6 7 8 — g 10 mn NO
e IC Block Diagram

QI
D3
1IS2835
Pe
Se
Q2
aoe [KEY BOARD ) _ LCD101
LIQUID CRYSTAL DISPLAY PANEL
IC1 CXA1019S
FM/AM

A est SWITCH D2 AF R ippteAF

F I\LTERIN
OET AFC AFC IF FM AM BANO

s=
OUT AGC AGC GNO METER N.C IF INIF IN SELECT
A aes KVI560-TROO i [A]RADIO|[B]BUZZER| BATT TIMER
ees Q3
ANT0 FM <= <==
MW 2SC1623-TIL6 LW/MW || | |‘ | | | |
LW SWITCH | /\ AM Tun inc
ING METER
METE ||
| RS4 10k (0) Ql 0 PM i e WY
MHz tot
2SC2223-TIF13 {(O> 2SA8I2-TIMS —-, emma oR ® cme Zz
FM OSC MUTE

KK MIMOIOLGE®)
EXE) Sidi : ALARM RESET
RADIO OFF

IC101 $102 :
t
Q101 BeoI724 89-187 $103 * | REPEAT ALARM/SLEEP OFF
2SC2223-TIFI3
VCO BUFFER AMP Cope ee GNO GNO FM NF VOL AM AFC FM REQ FM AM N.C FM~ FE FM/AM
SLEEP OISCRI osc OSC OUT RF RF IN RF EN GND IF OUT
$104 RADIO ON

S105 : ALARM 8: BUZZER

| $106
.
BAND
D101 F
ef ISS133 $107 TIME SET TUNE -
0416, 2 (1, cDIt
5 1.2.(1.4) ake ey— $108 :
+ ALARM A: RADIO
1 WAKE UP STATION
L
MW/ LW LCD13 Dyer,
C FERRITE $109 ALARM MODE
ROD B ee LCD14 (63) al
ANTENNA LCDIS @}—
7 $110 TIME SET TUNE +
Lep16

: nc GE
el—
$111

S¥12 :
ENTER / CLOCK

z|2 <20 | | 182835

ofé Se ae ed
Sie: TIMER

28 00
& - K2 Cree a

C9 |5p cn l2p C6 I3p T I6p

cs
=
2
2
=
oo os
uu _ DIIO-Dil2
1S2837-Tl
| a Few zd
D 1.0k SZ ESBZE
Q4 Li-l <<
oO “f
@@ia6a
qvos
2
2SC1623-TIL6 oO I R23 RNB |C123 R121
| LW SWITCH re wae ne ff 2 82 6
07 oe_ (13) OOO)
al 0,7
2SC1623-TIL6
MW/LW SWITCH

Sil
- C30 220p

R28 2.2K
SP!
SPEAKER
Q104, Q105
2SCI623-TIL6
LOWPASS FILTER Q102
1 Note:
2SA8I12-TIMS
VOLTAGE DETECTOR e All capacitors are in wF unless otherwise noted. pF: uwuF
[ R113 $106 S109 Sii2 Sil3 SOWV or less are not indicated except for electrolytics
Q103 12k and tantalums.
a
2SC1625-TILS
VOLTAGE DETECTOR @ All resistors are in 2 and '/,W or less unless otherwise
specified.
RiI2z6 =©D103 e & : internal component.
fF Ik 1S2835-T!
=
an Note:
2SC1623-TIL6 The components identi-
AM/FM SWITCH a fied by mark or dot-
res ted line with mark
are critical for safety.
Replace only with part
number specified.

e Voltage and waveforms are dc with respect to ground

under no-signal (detuned) conditions.
Ql2 no mark: FM
2SC1623-TILE ( ): MW
LW SWITCH
< = OLVV
_@ Voltages are taken with a VOM (Input Impedance 10M 2).
Voltage variations may be noted due to normal produc-
D105, D106 RN2 47k Q106 Di02 tion tolerances.
SLH-34MC3 2SC2001TP-K2 roPiGoa | ® Signal path.
RIPPLE FILTER
cS :FM
ICF-C103L
SECTION 5
EXPLODED VIEWS

NOTE: * Items marked ” * ” are not stocked

The components identified by
* -XX, -X mean standardized parts, so since they are seldom required for mark A or dotted line with mark
they may have some differences from routine service. Some delay should be are Critical for safety.
the original one. anticipated when ordering these items. eplace only with part number
specified.
* Color Indication of Appearance Parts * The mechanical parts with no reference
Example: number in the exploded views are not
AE9: French model
KNOB, BALANCE(WHITE)...(RED) supplied. 5AEQ9 : Swiss, Belgian model
D t * hardware (#mark) list is given in the
Parts color Cabinet’s color last of this parts list.

Ref. No. Part No. Description Remark Ref.No. Part No. — Description Remark

1 A-3635-751-A CABINET (UPPER) ASSY (UK) * 8 A-3661-574-A MAIN BOARD, COMPLETE (UK)
1 A-3635-781-A CABINET (UPPER) ASSY (AE9, 5AE9) + 8 A-3661-623-A MAIN BOARD, COMPLETE (AE9, 5AF9)
2 3-377-637-01 PANEL g 3-377-643-21 CABINET (LOWER)
3 1-692-143-11 SWITCH, RUBBER KEY 10 7-685-154-19 SCREW +P 3X35 TYPE2 NON-SLIT
4 7-685-648-79 SCREW +P 3X12 TYPE2 NON-SLIT 11 3-368-852-01 FOOT

#5 A-3679-396-A KEY BOARD, COMPLETE (UK) A\12 1-556-035-00 CORD, POWER (UK)
#5 A-3679-420-A KEY BOARD, COMPLETE (AE9, 5AE9) AM13 1-555-795-00 CORD, POWER (AE9, 5AE9)
* 6 3-377-644-01 CHASSIS SP1 1-503-082-00 SPEAKER
7 3-368-840-21 KNOB (VOL)
 SECTION 6
ELECTRICAL PARTS LIST KEY

NOTE:
@ Due to standardization, replacements in @ Items marked "*" are not stocked since The components identified by
yD

the parts list may be different from the they are seldom required for routine service. mark A\ or dotted line with mark.
parts specified in the diagrams or the Some delay should be anticipated A\ are critical for safety.
components used on the set. when ordering these items. Replace only with part number
@ -XX and -X mean standardized parts, so e SEMICONDUCTORS specified.
they may have some difference from the In each case, u:yt, for example:
original one. uA ..: “A. uPA. : sePA..
@ RESISTORS uPB..: PB. uPC..: gePC.. uPD..: sePD.. When indicating parts by
All resistors are in ohms. @ CAPACITORS . reference number, please
METAL: Metal-film resistor. uF: uF include the board.
METAL OXIDE: Metal oxide-film resistor. @ COILS
F :nonflammable uH: x2H :French model
AE9
5AE9 : Swiss, Belgian model

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

* A-3679-396-A KEY BOARD, COMPLETE (UK) C126 =©1-124-473-11 ELECT 1000uF 20% 10V
* A-3679-420-A KEY BOARD, COMPLETE (AE9, 5AE9) C127 =1-163-038-00 CERAMIC CHIP 0. luF 25V
Felooooiioooo ie ttoitoik C129 1-163-117-00 CERAMIC CHIP 100PF 5% 50V
C130 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V
* 3-377-639-01 HOLDER (LCD)
3-380-732-01 HOLDER (CRYSTAL) < JACK >

< CAPACITOR > * CNJ101 1-695-232-11 PIN, CONNECTOR (PC BOARD) 12P

C101 1-163-038-00 CERAMIC CHIP 0. 1uF 25V < DIODE >

C102 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
C103 1-163-038-00 CERAMIC CHIP 0. luF 25V D101 8-719-028-22 DIODE 188133
C104 1-163-117-00 CERAMIC CHIP 100PF 5% 50V D102 8-719-976-94 DIODE MA8051-M
C105 1-162-638-11 CERAMIC CHIP 1uF 16V Di03. =©8-719-104-34 DIODE 182836
D104 «=. 8- 719-200-682 DIODE 10E2
C106 1-125-701-11 CAP, DOUBLE LAYEYER 0. 047F (UK) D105 8-719-938-67 LED GL-3EG8
C106 1-125-733-31 CAP, DOUBLE LAYEYER 0. 047F (AES, 5AES)
C107 1-163-141-00 CERAMIC CHIP 0.00luF 5% 50V Di06 §=—.8- 719-938-67 LED GL-3EG8
C108 1-164-232-11 CERAMIC CHIP 0. OluF 10% dSO0V D107 +=©8-719-104-34 DIODE DAP202K-T-146
C109 1-163-008-11 CERAMIC CHIP 0.001uF 10% 50V D109 8-719-104-34 DIODE DAP202K-T-146 (AES, 5AE9)
D110 «=©.8-719- 400-18 DIODE MA152WK
C110 1-163-106-00 CERAMIC CHIP 36PF 5% 50V Di1i 8-719-400-18 DIODE MA152WK
C111. 1-163-096-00 CERAMIC CHIP 13PF Of 50V
C112 1-164-004-11 CERAMIC CHIP 0.tuF 10% 25V D112 8-719-400-18 DIODE MALS2WK
C113 =1-164-232-11 CERAMIC CHIP 0. OluF 10% 5S0V
C114 =41-164-232-11 CERAMIC CHIP 0. OluF 10% 50V < Ie >

C115 1-163-009-11 CERAMIC CHIP 0.00iuF 10% S0V 10101 8-759-073-89 IC uPD1724GB-589-1A7
C116 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C117. 1-163-009-11 CERAMIC CHIP 0.001uF 10% d0V < JUMPER RESISTOR >
C118 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C119 1-163-031-11 CERAMIC CHIP 0. OluF IOV JRiO2 1-216-295-00 METAL CHIP 0 OM 1/10¥
JRIG3 1-216-295-00 METAL CHIP 0 ay 1/10¥
Ci20 1-128-483-11 ELECT 220uF 20% 25V JR104 1-216-296-00 METAL CHIP 0 5% 1/8W
C121 1-163-031-11 CERAMIC CHIP 0. OluF 50V JR105 1-216-295-00 METAL CHIP 0 5% 1/10W
C122 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V JRi06 1-216-295-00 METAL CHIP —0 5% 1/10¥
C123 1-164-006-11 CERAMIC CHIP 0. 33uF 10% 16¥
C124 1-164-232-11 CERAMIC CHIP 0. OiuF 10% 50V JRi07 1-216-295-00 METAL CHIP 0 o% 1/10W
JR1i08 1-216-295-00 METAL CHIP 0 On 1/108.
C125 1-126-176-11 ELECT 220uF 20% 10V JRI09 1-216-295-00 METAL CHIP 0 5% 1/10W
KEY

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

JR110 1-216-296-00 METAL CHIP 0 oO” 1/8W SW103 1-692-143-11 RUBBER SWITCH (REPEAT ALARM/SLEEP.OFF)
JRI11 1-216-295-00 METAL CHIP 0 oO” 1/10W SW104 1-692-143-11 RUBBER SWITCH (SLEEP/RADIO ON)
JR112 1-216-296-00 METAL CHIP 0 5% 1/8W SW105 1-692-143-11 RUBBER SWITCH (ALARM B BUZZFR/P2)
JR113 1-216-286-00 METAL CHIP 0 5% 1/8W SW106 1-692-143-11 RUBBER SWITCH (BAND)
JR114 1-216-296-00 METAL CHIP 0 o% 1/8W SW107 1-692-143-11 RUBBER SWITCH (-)

JR115 1-216-295-00 METAL CHIP 0 Om 1/10¥ SW108 1-692-143-11 RUBBER SWITCH (ALARM A RADIO/
JRi16 1-216-295-00 METAL CHIP 0 ay4 1/10¥ Pi WAKE UP STATION)
JRIi7 1-216-296-00 METAL CHIP 0 ay4 1/8W ~ SWi09 1-692-143-11 RUBBER SWITCH (ALARM MODE/P5)
JR118 1-216-296-00 METAL CHIP 0 ay4 1/8¥ SW110 1-692-143-11 RUBBER SWITCH (+)
SW111 1-554-088-00 SWITCH, KEY BOARD (ENTER/CLOCK)
< LCD >
SW112 1-682-143-11 RUBBER SWITCH (P4)
LCD101 1-809-707-11 DISPLAY PANEL, LIQUID CRYSTAL SW113 1-692-143-11 RUBBER SWITCH (TIMER)

< TRANSISTOR > < TRANSFORMER >

Q102 8-729-216-22 TRANSISTOR 2SA1162-G AT101 = 1-450-923-11 TRANSFORMER, POWER

Q103 8-729-120-28 TRANSISTOR 2S8C1623-L5L6
Q104 8-729-120-28 TRANSISTOR 2S8C1623-L5L6 < AC TERMINAL >
Qi05 8-729-120-28 TRANSISTOR 2SC1623-L5L6 TP1 = 1-535-771-11 AC TERMINAL (AE9, 5AE9)
Q106 8-729-142-46 TRANSISTOR 2SC2001-LK TP1 = 1-535-771-21 AC TERMINAL (UK)
TP2 = 1-535-771-11 AC TERMINAL (AES, 5AE9)
< RESISTOR > ee
&
TP2 1-535-771-21 AC TERMINAL (UK)

R101 1-216-049-00 METAL CHIP 1K 65% 1/10¥ | < VIBRATOR >

R102 1-216-081-00 METAL CHIP 22K = O% 1/10W
R103) =.1-216-065-00 METAL CHIP 4.7K 5% 1/10¥ X101 1-567-769-11 VIBRATOR, CRYSTAL
R104 1-216-001-00 METAL CHIP 10 5Y 1/10W SEC IO III TOR II I III OIG RO IIo a iaik
R106 =©1-216-087-00 METAL CHIP 100K 5% 1/10W
| * A-3661-574-A MAIN BOARD, COMPLETE (UK)
R107 1-216-113-00 METAL CHIP 470K 5% 1/10W * A-3661-623-A MAIN BOARD, COMPLETE (AE9, 5AE9)
R108 1-216-113-00 METAL CHIP 470K 5% 1/10W FESSORak
R109 1-216-059-00 METAL CHIP 2.7K 5% 1/10¥
R110 =.1-216-220-00 METAL GLAZE 8.2K 5% 1/8¥ | < CAPACITOR >
R112 1-216-089-00 METAL CHIP 47K 5% 1/10W
C1 1-163-125-00 CERAMIC CHIP 220PF 0% o0V
R113 = 1-216-051-00 METAL CHIP 1.2K 5% 1/10¥ C2 1-163-127-00 CERAMIC CHIP 270PF 0% © O0V
R114 =.1-216-067-00 METAL CHIP 9.6K 5% 1/10¥ | C3 1-163-121-00 CERAMIC CHIP 150PF 0% SOV
R115 = 1-216-067-00 METAL CHIP 0.6K 5% 1/10¥ 04 1-164-232-11 CERAMIC CHIP 0.01uF 10% 50V
Ri16 = =©1-216-067-00 METAL CHIP 0.6K 5% 1/108 05 1-164-232-11 CERAMIC CHIP 0.01uF 10% 50V
R117 =.1-216-067-00 METAL CHIP 9.6K 5% 1/10¥
C6 1-163-096-00 CERAMIC CHIP 13PF 3% d0V
R118 = =1-216-073-00 METAL CHIP 10K 65%) /10W C8 1-163-098-00 CERAMIC CHIP 16PF 3% = SOV
R119 = =1-216-246-00 METAL GLAZE 100K 5% 1/8W C9 1-163-087-00 CERAMIC CHIP 15PF 0% o0V
Ri20 = 1-216-065-00 METAL CHIP 4.7K 5% 1/10W Cid} 1-163-096-00 CERAMIC CHIP 13PF 0% = S0V
R121 1-216-073-00 METAL CHIP i0K 5% = 1/10W C11 = 1-163-095-00 CERAMIC CHIP 12PF 0% d0V
R123 1-216-049-00 METAL CHIP 1K 5% 1/10W
: Ci2 1-163-097-00 CERAMIC CHIP 15PF § 5% 5OV
R124 1-216-023-00 METAL CHIP 82 5% =~ /10W C13. =:1-163-117-00 CERAMIC CHIP 100PF 3% ©30V
R125 = 1-216-023-00 METAL CHIP 82 5% 1/108 C14 = 1-164-346-11 CERAMIC CHIP uF 16V
R126 =.1-216-049-00 METAL CHIP 1K 5% ©=©61/10W C15 = 1-163-117-00 CERAMIC CHIP 100PF 0% = 00V
RiZ7 = 1-216-198-00 METAL CHIP 1K 865%) ~—O1/8W C17 =: 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V

< SWITCH > 7 C18 = 1-163-141-00 CERAMIC CHIP 0.00iuF 5% 50V

C19 = 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
SW101 1-692-143-11 RUBBER SWITCH (ALARM RESET/RADIO OFF) C20 1-163-089-00 CERAMIC CHIP 6PF Q.25PF 50V
SWi02 = 1-692-143-11 RUBBER SWITCH (P3) C21 1-163-085-00 CERAMIC CHIP 2PF o0V

The components identified by

mark A\ or dotted line with mark.
A\ are critical for safety.
Replace only with part number
specified.
 ICF-C103L

KEY

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

C22 1-164-232-11 CERAMIC CHIP 0.01uF 10% DOV < IC >

623 1-164-232-11 CERAMIC CHIP 0.01uF 10% o0V
C24 1-163-130-00 CERAMIC CHIP 360PF [C1 8-752-035-2838 I¢ CXA1019S
C25 1-163-017-00 CERAMIC CHIP 0.0047uF 5% o0V
C26 1-163-128-00 CERAMIC CHIP 300PF 5% o0V < JUMPER REST STOR >

C27 1-163-009-11 CERAMIC CHIP 0.00iuF 10% 30V Rt 1-216-296-00 METAL CHIP 1/8W
628 1-163-031-11 CERAMIC CHIP 0. OluF . o0V JR2 1-216-296-00 METAL CHIP 1/8W
¢29 1-124-927-11 ELECT 4. TuF 20% 100V JR3 1-216-296-00 METAL CHIP 1/8W
C30 1-163-125-00 CERAMIC CHIP 220PF o% 30V JRA 1-216-296-00 METAL CHIP 1/8¥
C31 1-164-232-11 CERAMIC CHIP 0.01uF =10% o0V IRS 1-216-296-00 METAL CHIP 1/8¥

C32 1-124-9$27-11 ELECT 4, 7uF 20% 100V JR? 1-216-296-00 METAL CHIP 1/8W
C33 1-124-907-11 ELECT 10uF 20% o0V JR 1-216-296-00 METAL CHIP 1/8W
C34 1-163-986-00 CERAMIC CHIP 0.027uF 10% 25V JRI0 1-216-295-00 METAL CHIP 1/10W
C35 1-163-809-11 CERAMIC CHIP 0.047uF 10% 20V JR12Z 1-216-295-00 METAL CHIP 1/10W
C37 1-126-233-11 ELECT . 22uF 20% o0V JR13 1-216-296-00 METAL CHIP 1/8W

038 1-164-004-11 CERAMIC CHIP 0. luF 10% 25V JR14 1-216-295-00 METAL CHIP 1/10W
C39 1-124-472-11 ELECT 470uF 20% 10V JRIS 1-216-296-00 METAL CHIP 1/8W
C41 1-164-346-11 CERAMIC CHIP uf 16V JR16 1-216-296-00 METAL CHIP 32
ae
ae
ay
oT
on 1/8W
C42 1-163-092-00 CERAMIC CHIP 9PF —Q. 25PF o0V JR17 1-216-296-00 METAL CHIP 1/8W
C43 1-126-176-11 ELECT 220uF 20% 10V JR18 1-216-296-00 METAL CHIP eco
ao
co
&
oo
ao
Qo
&
oo 1/8W

C44 1-124-907-11 ELECT 10uF 20% o0V JRI9 1-216-296-00 METAL CHIP 1/8W
C45 1-164-232-11 CERAMIC CHIP 0. OluF o0V JR20 1-216-296-00 METAL CHIP onae 1/8W
C46 1-163-059-00 CERAMIC CHIP 0.O0luF 10% o0V JR21 1-216-295-00 METAL CHIP 1/10¥
C47 1-164-232-11 CERAMIC CHIP 0. OluF o0V JR22 1-216-296-00 METAL CHIP &
2]
oo 1/8W
C48 1-164-232-11 CERAMIC CHIP 0. OluF o0V
< COIL >
C49 1-124-$10-11 ELECT ATuF 20% o0V
C50 1-163-117-00 CERAMIC CHIP 100PF o% o0V L2 1-402-615-11 ANTENNA, FERRITE-ROD (MW/LW)
L3-1 1-402-654-11 COIL, AIR-COR E
< FILTER > L3-2 1-402-653-11 COIL, AIR-COR E
L4 1-460-335-11 COIL (WITH CO RE)
CF1 1-578-677-21 FILTER, CERAMIC L5 1-406-485-11 COIL (OSC)
CF2 1-579-312-81 FILTER, CERAMIC
CF3 1-579-312-81 FILTER, CERAMIC < TRANSISTOR >

< CONNECTOR > Qi 8-729-141-75 TRANSISTOR 28D596DV345

Q2 8-729-123-86 TRANSISTOR 25K238-K16
CNJ1 1-580-181-11 SOCKET, CONNECTOR 2P Q3 8-729-120-28 TRANSISTOR 2801623-L5L6
CNP 1-695-237-11 SOCKET, CONNECTOR(PC BOARD) 12P Q4 8-728-120-28 TRANSISTOR 2861623-LOL6
QI 8-729-120-28 TRANSISTOR 2S801623-L5L6
< TRIMMER >
Q8 8-729-102-07 TRANSISTOR 2802223-F13
CT1 1-141-304-21 TRIMMER, CERAMIC Q9 8-729-102-07 TRANSISTOR 2862223-F13
CT2 1-141-443-11 TRIMMER, CERAMIC Q10 8-729-216-22 TRANSISTOR 2SA1162-G
CT3 1-141-304-21 TRIMMER, CERAMIC Qi1 8-729-120-28 TRANSISTOR 2861623-L5L6
CT4 1-141-444-91 TRIMMER, CERAMIC Q12 8-729-120-28 TRANSISTOR 2801623-L5L6

< DIODE > < RESISTOR >

D1 8-719-951-05 DIODE KV1560 1-216-049-00 METAL CHIP 1K 3% 1/10W

D2 8-719-951-05 DIODE KV1560 1-216-039-00 METAL CHIP 390 5% 1/10W
D3 8-719-104-34 DIODE 182835 1-216-174-00 METAL GLAZE 100 5% 1/8W
D4 8-719-948-46 DIODE 1732 1-216-133-00 METAL CHIP 3.3M 5% 1/10W
DS 8-719-949-46 DIODE 1732 1-216-133-00 METAL CHIP 3. 3M 5% 1/10W
ICF-C103L

KEY

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

R6 1-216-057-00 METAL CHIP 2. 2K 5% 1/10¥ ACCESSORIES & PACKING MATERIALS

R7 1-216-009-00 METAL CHIP 22 5% 1/10¥ AO OR ok foiiookoitototok
tok doioiiok

R8 1-216-198-00 METAL CHIP 1K 5% 1/8W

R9 1-216-073-00 METAL CHIP 10K 5% 1/10¥ 1-501-499-11 COUPLER, ANTENNA (5AES)
Ri0 1-216-073-00 METAL CHIP 10K 5% 1/10W * 3-378-685-01 INDIVIDUAL CARTON
3-755-140-11 MANUAL, INSTRUCTION
R11 1-216-097-00 METAL CHIP 100K 5% 1/10¥ (ENGLISH, FRENCH, GERMAN)
R12 1-216-097-00 METAL CHIP 100K 5% 1/10¥ 3-755-140-41 MANUAL, INSTRUCTION
R13 1-216-097-00 METAL CHIP 100K 5% 1/10W (SPANISH, DUTCH, ITALTAN) (5AES)
Ri4 1-216-097-00 METAL CHIP 100K 5% 1/10W
R15 1-216-061-00 METAL CHIP 3. 3K 5% 1/10W

R16 1-216-077-00 METAL CHIP 15K 5% 1/10¥

Ri7 1-216-186-00 METAL GLAZE 330
R18 1-216-121-00 METAL CHIP iM 5% 1/10¥
R19 1-216-057-00 METAL CHIP 2. 2K 5% 1/10¥
R20 1-216-049-00 METAL CHIP 1K 5% 1/10W

R21 1-216-220-00 METAL GLAZE 8. 2K 5% 1/8W

R23 1-216-081-00 METAL CHIP 22K 5% 1/10¥
R24 1-216-017-00 METAL CHIP 47 5% 1/10¥
R25 1-216-081-00 METAL CHIP 22K 5% 1/10¥
R26 1-216-073-00 METAL CHIP 10K 5% 1/10¥

R27 1-216-033-00 METAL CHIP 220 5% 1/10¥

R28 1-216-057-00 METAL CHIP 2. 2K 5% 1/10W
R29 1-216-121-00 METAL CHIP 1M 5% 1/10¥
R32 1-216-049-00 METAL CHIP 1K 5% 1/10W
R33 1-216-073-00 METAL CHIP 10K 5% 1/10W

R34 1-216-073-00 METAL CHIP 10K 5% 1/10W

R35 1-216-001-00 METAL CHIP 10 5% 1/10W

< VARIABLE RESISTOR >

RV1 1-241-586-11 RES, VAR, CARBON 50K

< TRANSFORMER >

Ti 1-404-790-11 TRANSFORMER, IF
OR ik ioitokkokiodiokkokiok doi ioiok dokloiokoiiokokktoiokoiougokoioktoiotokotokk
tok tok tok

MISCELLANEOUS
Ak kok kf fof fefok

3 1-692-143-11 SWITCH, RUBBER KEY

Al2 1-556-035-00 CORD, POWER (UK)
A\13 1-555-795-00 CORD, POWER (AE9, 5AE9)
SPI 1-503-082-00 SPEAKER

folosoioiobo i doloii doi i ilo doiidioid olla i iiol a iio ioioi i dokioioiciolaii dg ioioiok

The components identified by

mark A\ or dotted line with mark.
A\ are critical for safety.
Replace only with part number
specified.

English

Sony Corporation
ne
Becta ae
‘Printed in Japan
9-957-293-11 Personal Telecommunication Group ©1992.7
Published by Customer Relations and Service Group
— 18—