Your Company Name Project: Page # ___

Engineer: 24/02/2025
Descrip: F-1
ASDIP Foundation 5.0.0.1 SPREAD FOOTING DESIGN www.asdipsoft.com

GEOMETRY SOIL PRESSURES (D+0.75L+0.75S+0.525E)

Footing Length (X-dir) ....... 2.25 m Gross Allow. Soil Pressure .. 125.0 KN/m²
Footing Width (Z-dir) ......... 2.25 m Soil Pressure at Corner 1 .... 106.3 KN/m²
Footing Thickness ............. 40.0 cm OK Soil Pressure at Corner 2 .... 63.0 KN/m²
Soil Cover ......................... 1.00 m Soil Pressure at Corner 3 .... 19.7 KN/m²
Column Length (X-dir) ...... 30.0 cm Soil Pressure at Corner 4 .... 63.0 KN/m²
Column Width (Z-dir) ........ 50.0 cm Bearing Pressure Ratio .......... 0.85 OK
Offset (X-dir) ..................... 0.00 cm OK Ftg. Area in Contact with Soil .. 100.0 %
Offset (Z-dir) ..................... 0.00 cm OK X-eccentricity / Ftg. Length ...... 0.06 OK
Pedestal Height .................. N. A. Z-eccentricity / Ftg. Width ......... 0.06 OK

APPLIED LOADS
Dead Live RLive Snow Wind Seismic
Axial Force P ............. 140.0 40.0 0.0 0.0 0.0 70.0 KN
Moment about X Mx .. 10.0 10.0 0.0 0.0 0.0 45.0 KN-m
Moment about Z Mz .. 10.0 10.0 0.0 0.0 0.0 45.0 KN-m
Shear Force Vx ......... 0.0 0.0 0.0 0.0 0.0 0.0 KN
Shear Force Vz ......... 0.0 0.0 0.0 0.0 0.0 0.0 KN

OVERTURNING CALCULATIONS (Comb: 0.6D+0.7E)

OVERTURNING RESISTING
Force Arm Moment Force Arm Moment
- About X-X KN m KN-m - About X-X KN m KN-m
Moment Mx ........... --- --- 37.5 Footing Weight .. 29.2 1.13 32.8
Shear Force Vz .... 0.0 0.40 0.0 Column Weight .. 0.0 1.13 0.0
Passive Pressure 0.0 0.16 0.0 Soil Cover .......... 50.1 1.13 56.4
Rh = 0.0 OTM = 37.5 Axial Force P ..... 133.0 1.13 149.6
- About Z-Z Water Buoyancy . -11.9 1.13 -13.4
Moment Mz ........... --- --- 37.5 Rv = 200.3 RM = 225.4
Shear Force Vx .... 0.0 0.40 0.0 - About Z-Z
Passive Pressure 0.0 0.16 0.0 Footing Weight .. 29.2 1.13 32.8
Rh = 0.0 OTM = 37.5 Column Weight .. 0.0 1.13 0.0
Soil Cover .......... 50.1 1.13 56.4
X-X Z-Z Axial Force P ..... 133.0 1.13 149.6
Arm of Vertical Resultant = 0.94 0.94 m Water Buoyancy . -11.9 1.13 -13.4
Overturning Safety Factor = 6.01 6.01 > 1.1 Rv = 200.3 RM = 225.4
OK

1 of 4
 Your Company Name Project: Page # ___
Engineer: 24/02/2025
Descrip: F-1
ASDIP Foundation 5.0.0.1 SPREAD FOOTING DESIGN www.asdipsoft.com

SLIDING (combDlg. 0.6D+0.6W)

Footing-Soil Friction Coeff. ..... 0.45
Friction Force at Base ............. 68.1 KN
Passive Pressure Coeff. Kp .... 4.33
X-X Z-Z
Passive Force @ Ftg ... 79.4 79.4 KN
Horiz. Resisting Force 147.5 147.5 KN
Horiz. Sliding Force ..... 0.0 0.0 KN
Sliding Safety Factor ... 99.99 99.99 > 1.5 OK

UPLIFT (Comb: 0.6D+0.6W)

Uplift Force P .................... 0.0 KN
Pedestal Selfweight ............ 0.0 KN
Footing Selfweight .............. 29.2 KN
Soil Cover Weight ............... 50.1 KN
Downward Force W ........... 79.3 KN
Uplift Safety Factor ............. 99.99 > 1.0 OK

PUNCHING SHEAR (Comb: 1.2D+0.5L+0.2S+E)

Unbalanced Moment Factor Ɣvx ... 0.43
Unbalanced Moment Factor Ɣvz ... 0.37
Punching Shear due to Axial .... 271.2 KPa
Punching Shear due to Mx ....... 120.4 KPa
Punching Shear due to Mz ....... 116.4 KPa
Punching Shear Stress Vu ...... 508.0 KPa
Effective Perimeter bo ............. 282.0 cm
Average Effective Depth d ...... 30.5 cm
Column Location Factor αs .... 40 (Interior)
Column Aspect Ratio β ........... 1.67
Punching Shear Strength ϕVc .. 1134.2 KPa
Punching Shear Ratio Vu/ϕVc ..... 0.45 OK

2 of 4
Your Company Name Project: Page # ___
Engineer: 24/02/2025
Descrip: F-1
ASDIP Foundation 5.0.0.1 SPREAD FOOTING DESIGN www.asdipsoft.com

ONE-WAY SHEAR (Comb: 1.2D+0.5L+0.2S+E) TRANSFER (Comb: 1.2D+0.5L+0.2S+E)

- Side + Side Bearing Under-strength ϕ Factor ....... 0.65
One-way Shear Vux ... 42.0 111.6 KN Use 12 #6 x 0.91 m hooked dowels , As = 34.06 cm²
One-way Shear Vuz ... 33.9 96.8 KN Bearing Stress Pbu .................. 14.9 MPa
Under-strength ϕ Factor ............. 0.75 Column Bearing Strength ϕPn ... 15.7 MPaOK
One-way Shear Strength ϕVcx 275.9 KN OK Footing Bearing Strength ϕPn ... 27.3 MPaOK
One-way Shear Strength ϕVcz 264.6 KN OK Shear Force Transfer Vu ........... 0.0 KN
Max. One-way Shear Ratio Vu/ϕVc .. 0.40 OK Shear Friction Strength ϕVn ...... 423.1 KN OK
Min. Steel Area As = 0.005 A1 ... 15.00 cm² OK
FLEXURE (Comb: 1.2D+0.5L+0.2S+E) Develop. Length Ratio at Column ..... 0.37 OK
- Top Bars - - Side + Side Develop. Length Ratio at Footing ..... 0.87 OK
Bending Moment -Mux ... 0.0 0.0 KN-m
Bending Moment -Muz ... 0.0 0.0 KN-m
No Top Reinforcement Provided at the Footing
Use Plain Concrete Flexural Strength at Top
X-Bars Development Length Ratio .. N.A.
Z-Bars Development Length Ratio .. N.A.
Min. Top Steel Area Ratio ............... N.A.
Under-strength ϕ Factor .................. 0.60
Bending Strength -ϕMnx ........ 69.3 KN-m OK
Bending Strength -ϕMnz ........ 69.3 KN-m OK
Max. Bending Ratio -Mu/ϕMn ........... 0.00 OK
Max. Bar Spacing Ratio ................... N.A.
- Bottom Bars - - Side + Side
Bending Moment +Mux ... 23.4 65.0 KN-m
Bending Moment +Muz ... 30.0 79.6 KN-m
Use 12 #6 Bars Parallel to X (Bot) , d = 31.4 cm
Use 12 #6 Bars Parallel to Z (Bot) , d = 29.5 cm
X-Bars Development Length Ratio .. 0.33 OK
Z-Bars Development Length Ratio .. 0.37 OK
Min. Bottom Steel Area Ratio ........... 0.48 OK
Under-strength ϕ Factor .................. 0.90
Bending Strength +ϕMnx ........ 240.0 KN-m OK
Bending Strength +ϕMnz ........ 256.2 KN-m OK
Max. Bending Ratio +Mu/ϕMn ........... 0.31 OK
Max. Bar Spacing Ratio ................... 0.42 OK

3 of 4
Your Company Name Project: Page # ___
Engineer: 24/02/2025
Descrip: F-1
ASDIP Foundation 5.0.0.1 SPREAD FOOTING DESIGN www.asdipsoft.com

DESIGN CODES
Concrete Design ................ ACI 318-19
Load Combinations ............ ASCE 7-10/16

MATERIALS
Column Concrete f'c ........ 21.0 MPa
Column Dowels fy ............ 276.0 MPa
Column Ties fy ................. 276.0 MPa
Footing Concrete f'c ......... 21.0 MPa
Footing Rebars fy ............. 276.0 MPa
Soil Cover Density ............ 17.0 KN/m³

COLUMN (Comb: 1.2D+0.5L+0.2S+E)

Axial Load Pu ...................... 258.0 KN
Bending Moment Mu ............ 87.7 KN-m
Axial Strength ϕPn ............... 1849.6 KN
Flexural Strength ϕMn ......... 139.4 KN-m
Biaxial Strength Ratio ................. 0.63 OK

4 of 4