Product Introduction
The ZP930-A product adopts a 3.1-inch LCD VA black film color screen, with light
buttons,matte textured black . The functional area distribution of the instrument interface
is clear and intuitive, and the high-brightness LED backlight is selected, and the display
content is still clearly visible in the sun. The product adopts nylon buckle, ABS shell,
hardened PC mirror waterproof glass, the product can be used normally in the
temperature of -25℃-80℃, and can ensure good electrical performance and mechanical
performance.
⚫ FUNCTION：
1. Display function
Battery indicator, Malfunction indicator ,Gear indicator,
Speed indicator, Cruise indicator, Headlight icon,
6KM boost indicator, Unit indicator and Bluetooth icon display.
2. Communication protocol：UART
3. Contents on the display
Display content introduction
1) Speed & Power display,The Maximum display to 199KM/H
2) Voltage status level
From bottom to top, the battery level increases sequentially, the lowermost display grid represents
low battery, and the uppermost display grid represents high battery. The left side displays the corresponding remaining
battery percentage (percentage example display)
3)Multifunctional display area
Display: total mileage, single mileage, real-time voltage display, running time prompt, fault prompt, switch handle
voltage value
4).Fault status display area
The number corresponding to the multi-function area represents the corresponding fault content. The specific status is
as follows:
ERRO 1：Motor failure
ERRO 2：Accelerator throttle failure
ERRO 3：Controller failure
ERRO 4: Brake failure
ERRO 5：Undervoltage protection
ERRO 6：Communication failure, the display cannot receive the output from the controller
ERRO 7：Communication failure, the controller cannot receive the output from the display
5).Gear display
6).Single/dual drive riding mode selection, the default mode is single drive
S-drive: One motor drive D-drive: Two motors drive
7).Starting mode of the scooter
ECO: Non-zero startup mode NORMAL: Zero startup mode
8).Accessibility display
Cruise mode / 6KM boost mode / Headlights on reminder
USB charging prompt (Not supported) /
Bluetooth connection status prompt USB (Not supported)
⚫ INTRODUCTION TO KEY FUNCTIONS：
UP
DW
ON/OFF
1)ON/OFF Button : POWER ON/POWER OFF
1.1 Press and hold the ON, OFF button for 3 seconds to turn on/off.
1.2 Short press the ON/OFF button to turn on/off the headlight.
2)UP Button： GEAR UP
2.1：Short press the UP button to increase the gear
2.2: Press and hold the UP button to enable/disable dual drive mode.
3)DW Button：GEAR DOWN
3.1 Short press the DW button to downshift
3.2 Long press the DW button to enter/exit the 6KM boost mode (need to be supported by a controller)
4)Function menu settings
Press the UP button&DW button at the same time to enter the function menu interface. Short press the ON/OFF button
to switch function options, short press the UP button or DW button to set the corresponding parameter value. After the
setting is completed, press the UP& DW button at the same time to exit.
5)Parameter setting and definition
P02：mileage unit，0：KM；1：MILE； default: 0
P03：Voltage mode； default: 60V
P04：Sleep time： from 0-60mins（0 means always on ,default: 5mins)
P06: Wheel diameter：calculated by inch；precision：0.1； default: 10
P07:Number of tachometer magnets：Range：1-100； Default: 30
P09：Zero start/non-zero start settings，0：Zero start；1：Non-zero start ；Default: 1
P10：Smart speed limit settings, 0:Speed released, 1:Speed locked；Default: 1
P12：Activate strength setting.Range:from 0 to 5， 5 most power；Default: 5
P15：Motor drive signal percentage setting， Range：from 1 to 100; Default: 100
P16：Auto cruise setting， 1:Auto cruise Activated 0 Auto cruise Locked ； Default: 0
P99：Restore to initial settings
Enter the menu, short press the plus or minus key, the value 00099 flashes, and the display returns to the main
interface after long-pressing the plus key for 5 seconds, the setting is successfully done.
ODO: To clear ODO
In the ODO parameter setting interface, briefly press the + button and then press and hold for 5-6 seconds until the
number is zero.
⚫ INTRODUCTION OF CONNECTORS AND DEFINITIONS
1 2
5 4
Connector 1: 3P-accelerator interface Connector 2: 4P-Three-position button interface
GND DW(-) UP(+)
ZB ) )
(转把电压）
VCC ON/OFF GND
)
Connector 3: 6p-Instrument connection controller interface Connector 4&5: 2P-brake interface
BAT+ BAT- SL
DS ZB
TX RX GND
Note: Due to the upgrade of the company's products, the displayed content of the product you get may be
different from the manual, but it will not affect your normal use.
