0% found this document useful (0 votes)
32 views17 pages

Siemens Hipath 4000 Release 1.0 To A Cisco Iad243X Using E1-Isdn Net5 With Sip

This application note details the connectivity setup between a Siemens HiPath 4000 Release 1.0 and a Cisco IAD243X Gateway using E1-ISDN NET5 with SIP. It outlines hardware and software requirements, supported and unsupported features, and provides configuration instructions for both the HiPath 4000 PBX and the Cisco IAD2432. Limitations of the system are also discussed, particularly regarding call forwarding and connected number interoperability.

Uploaded by

eltonkiprono528
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
32 views17 pages

Siemens Hipath 4000 Release 1.0 To A Cisco Iad243X Using E1-Isdn Net5 With Sip

This application note details the connectivity setup between a Siemens HiPath 4000 Release 1.0 and a Cisco IAD243X Gateway using E1-ISDN NET5 with SIP. It outlines hardware and software requirements, supported and unsupported features, and provides configuration instructions for both the HiPath 4000 PBX and the Cisco IAD2432. Limitations of the system are also discussed, particularly regarding call forwarding and connected number interoperability.

Uploaded by

eltonkiprono528
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 17

Application Note

Siemens HiPath 4000 Release 1.0 to a Cisco IAD243X using E1-


ISDN NET5 with SIP
January 11, 2007 Initial Version
Table of Contents
Introduction .............................................................................................................................................................................................................. 1
Network Topology.................................................................................................................................................................................................... 2
Limitations................................................................................................................................................................................................................ 2
Hardware Requirements ...................................................................................................................................................................................... 3
Software Requirements ....................................................................................................................................................................................... 3
Features .................................................................................................................................................................................................................... 3
Features Supported .............................................................................................................................................................................................. 3
Features Not Supported ....................................................................................................................................................................................... 3
Configuration............................................................................................................................................................................................................ 3
Configuring the Siemens HiPath 4000 PBX........................................................................................................................................................ 3
Configuring the Hipath 4000 PBX ...................................................................................................................................................................... 4
Configuring the Cisco IAD2432 24FXS ........................................................................................................................................................... 11
Acronyms ............................................................................................................................................................................................................... 15

Introduction

This is an application note for connectivity to a Siemens HiPath 4000 Release 1.0 with a Cisco IAD243X Gateway via E1 ISDN NET5-
to-SIP communication (10/100baseT).

The network topology diagram (Figure 1) shows the test setup for end-to-end interoperability with the Cisco IAD243X Gateway
connected to the PBX via NET5 (E1 PRI). IP trunk connectivity between the Cisco IAD243X’s is achieved by using SIP protocol.

© 2007 Cisco Systems, Inc. All right reserved.


Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 1 of 17
EDCS#565420 Rev # Initial Version
Network Topology
Figure 1. Basic Call Setup

Limitations

On Call Forward No Answer local (e.g. Phone A calls Phone C CFNA to Phone D); the Cisco IAD243X must be set to Q921/Q931
Network side. If the Cisco IAD 243X is set to Q921/Q931 user side CFNA will not work.

Connected number (COLP) does not interoperate This is an Cisco IAD2432 limitation.

© 2007 Cisco Systems, Inc. All right reserved.


Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 2 of 17
Hardware Requirements
2 Cisco IAD2432 24FXS

1 Cisco Catalyst switch (CAT6500)

(1) Siemens HiPath 40000

DIU-N2
Software Requirements
Siemens HiPath 4000 Release 1.0

Cisco IOS Release: c2430-ik9o3s-mz-124-9.T1

Features

Features Supported
Basic end-to-end calls with CLIP (Calling Number)

Calling Number Restricted

Overlap Receiving

Call Transfer – Local and Network/External

Call on-hold

Call Forward (Unconditional, Busy and No answer) – local and network/external

3-way Conference
DTMF end-to-end
Features Not Supported
Calling Name and Connected Name presentation

Connected Number presentation

Configuration

Configuring the Siemens HiPath 4000 PBX

1. Add the new access code to Dialing Plans using WABE + LDPLN.
2. Add the new trunk board using BCSU.
3. Configure Class of Trunk using COT.
4. Configure Class of Parameter for device handler using COP.
5. Configure Class of Service using COSSU.
6. Add the new trunk group access code using BUEND.
7. Configure trunk using TDCSU.
8. Configure Reference Clock using REFTA.
9. Configure trunk Least Cost Routing using LDAT + RICHT.
10. Configure LCR Out-dial Rules using LODR.
11. Enable In-Band DTMF signaling for the Digital Stations using SBCSU.

© 2007 Cisco Systems, Inc. All right reserved.


Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 3 of 17
Configuring the Hipath 4000 PBX
DPLN
<dis-wabe:gen;
DIS-WABE:GEN;
H500: AMO WABE STARTED
------------------------------------------------------------------------------
| DIGIT INTERPRETATION VALID FOR ALL DIAL PLANS |
------------------------------------------------------------------------------
| | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT |
| CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO |
| |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE |
------------------------------------------------------------------------------
| 0 |. .**** ..*** **... ..... .*| CO | R |
| 001 - 009 |* ..... ..... ..... ..... ..| NETRTE | |
| 111 |. .**** ***** **... ..... .*| TIE | |
| 12 |. .**** ***** **... ..... .*| TIE | R |
| 13 - 14 |. .**** ***** **... ..... .*| TIE | |
| 21 |. ..... ..... ..... ....* ..| KNOVRKY | |
| 22 |. ..... ..... ..... ....* ..| DNDKY | |
| 222 |. .**** ***** **... ..... .*| TIE | |
| 23 |. ..... ..... ..... ....* ..| FWDKY | |
| 24 |. ..... ..... ..... ....* ..| MBKY | |
| 25 |. ..... ..... ..... ....* ..| MSGRKY | |
| 26 |. ..... ..... ..... ....* ..| DAKY | |
| 27 |. ..... ..... ..... ....* ..| DSSKY | |
| 28 |. ..... ..... ..... ....* ..| VCRKY | |
| 29 |. ..... ..... ..... ....* ..| VCKY | |
| 30 |. ..... ..... ..... ....* ..| CONFKY | |
------------------------------------------------------------------------------
| DIGIT INTERPRETATION VALID FOR ALL DIAL PLANS |
------------------------------------------------------------------------------
| | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT |
| CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO |
| |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE |
------------------------------------------------------------------------------
| 3000 - 3010 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 30 |
| | | |DNNO 0- 0-222 |
| 3011 - 3020 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 31 |
| | | |DNNO 0- 0- 31 |
| 3021 - 3030 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 32 |
| | | |DNNO 0- 0- 32 |
| 3031 - 3040 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 33 |
| | | |DNNO 0- 0- 33 |
| 3041 - 3050 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 35 |
| | | |DNNO 0- 0- 35 |
| 31 |. ..... ..... ..... ....* ..| NAMEKY | |
| 32 |. ..... ..... ..... ....* ..| PARKKY | |
------------------------------------------------------------------------------
| DIGIT INTERPRETATION VALID FOR ALL DIAL PLANS |
------------------------------------------------------------------------------
| | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT |
| CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO |
| |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE |
------------------------------------------------------------------------------
| 33 |. ..... ..... ..... ....* ..| CCKY | |
| 34 |. ..... ..... ..... ....* ..| HTKY | |
| 35 |. ..... ..... ..... ....* ..| STKY | |
| 36 |. ..... ..... ..... ....* ..| REMKY | |
| 36 - 37 |. .**** ..*** **... ..... .*| CO | |
| 38 |. ..... ..... ..... ....* ..| TIMEKY | |

© 2007 Cisco Systems, Inc. All right reserved.


Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 4 of 17
| 39 |. .**** ***** **... ..... .*| TIE | |
| 4000 - 4050 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 111 |
| | | |DNNO 0- 0-111 |
| 4051 - 4566 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 222 |
| | | |DNNO 0- 0-222 |
| 4567 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 34 |
| | | |DNNO 0- 0-200 |
------------------------------------------------------------------------------
| DIGIT INTERPRETATION VALID FOR ALL DIAL PLANS |
------------------------------------------------------------------------------
| | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT |
| CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO |
| |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE |
------------------------------------------------------------------------------
| 4568 - 4999 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 222 |
| | | |DNNO 0- 0-222 |
| 5000 - 5040 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 0 |
| | | |DNNO 0- 0-555*|
| 5500 - 5501 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 56 |
| | | |DNNO 0- 0-560 |
| 555 |. .**** ***** **... ..... .*| OWNNODE | |
| 560 |. .**** ***** **... ..... .*| TIE | |
| 59 |. .**** ***** **... ..... .*| TIE | |
| 6000 - 6009 |. .**** ***** **... ..... .*| STN | R |
| | | |DESTNO 0 |
| | | |DNNO 0- 0-555*|
------------------------------------------------------------------------------
| DIGIT INTERPRETATION VALID FOR ALL DIAL PLANS |
------------------------------------------------------------------------------
| | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT |
| CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO |
| |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE |
------------------------------------------------------------------------------
| 7000 - 7002 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 56 |
| | | |DNNO 0- 0-560 |
| 8000 - 8050 |. .**** ***** **... ..... .*| STN | |
| | | |DESTNO 222 |
| | | |DNNO 0- 0-222 |
| 8060 |. .**** ***** **... ..... .*| TIE | |
| 8070 |. .**** ***** **... ..... .*| TIE | |
| 83 |. .**** ..*** **... ..... .*| SPDC1 | |
| 84 |. .**** ..*** **... ..... .*| SPDC2 | |
| 88 |. ..... ..*.. ..... ..... .*| SCONSI | R |
| 89 |. ..... ...*. ..... ..... ..| SCONSCO | R |
| 9 |. .**** ***** **... ..... .*| TIE | |
| *13 |. ....* ..... ..... ..... ..| AHTVCE | |
| *15 |. *.... ..**. ..... ..... .*| SPLIT | |
| *16 |. ....* ..... ....* ..... ..| AREM | |
| *17 |. *.... ..**. ..... ..... ..| TRACE | |
------------------------------------------------------------------------------
| DIGIT INTERPRETATION VALID FOR ALL DIAL PLANS |
------------------------------------------------------------------------------
| | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT |
| CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO |
| |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE |
------------------------------------------------------------------------------
| *18 |. ....* ..... ..... ..... ..| ACOSX | |
| *19 |. *.... ..... ..... ..... ..| KNOVR | |
| *20 |. ....* ..... ..... ..... ..| ADND | |
| *25 |. ....* ..... ..... ..... ..| FWDTERM | |

© 2007 Cisco Systems, Inc. All right reserved.


Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 5 of 17
| *29 |. ....* ..... ....* ..... ..| AFFWDVCE | |
------------------------------------------------------------------------------

AMO-WABE -111 DIALLING PLANS, FEATURE ACCESS CODES


DISPLAY COMPLETED;

BCSU

PRI Board

<DISPLAY-BCSU:TYPE=TBL,LTG=1,LTU=2,SLOT=49;
DISPLAY-BCSU:TYPE=TBL,LTG=1,LTU=2,SLOT=49;
H500: AMO BCSU STARTED

ADDRESS : LTG 1 LTU 2 SOURCE GROUP 1


-----+-----------+---------+---+---+-+------------+-----+--------+------------+
| ASSIGNED | MODULE |FCT|HWY| | INSERTED | | | MODULE |
PEN | MODULE | TYPE |ID |BDL| | MODULE |STATE| HW-INFO| STATUS |
-----+-----------+---------+---+---+-+------------+-----+--------+------------+
49 | Q2196-X DIU-N2 1 A | | Q2196-X | 1 | -06 - | READY |

AMO-BCSU -111 BOARD CONFIGURATION, SWITCHING UNIT


DISPLAY COMPLETED;

Class of Trunk, COT

<dis-cot:21;
DIS-COT:21;
H500: AMO COT STARTED

COT: 21 INFO:
DEVICE: INDEP SOURCE: DB
PARAMETER:
PRIORITY FOR AC WILL BE DETERMINED FROM MESSAGE PRI
RECALL IF USER HANGS UP IN CONSULTATION CALL RCL
TRUNK CALL TRANSFER XFER
TRUNK SIGNALING ANSWER ANS
CHANGEOVER FROM HOLD TO RING TONE CHRT
KNOCKING OVERRIDE POSSIBLE KNOR
CALL EXTEND FOR BUSY, RING OR CALL STATE CEBC
NETWORKWIDE AUTOMATIC CALLBACK ON BUSY CBBN
NETWORKWIDE AUTOMATIC CALLBACK ON FREE CBFN
DON'T RELEASE CALL TO BUSY HUNT GROUP BSHT
CONNECTION TO ROUTE OPTIMIZATION NODE ROPT
TSC-SIGNALING FOR NETWORKWIDE FEATURES (MANDATORY) TSCS
INCOMING CDR BY ZONE OR FROM LINE ICZL
AOC PER CALL (AUTOMATICAL OR ON REQUEST), MAND. CORNET-NQ AOCC
LINE WITH IMPLICIT NUMBERS LINO
NO TONE NTON

AMO-COT -111 CLASS OF TRUNK FOR CALL PROCESSING


DISPLAY COMPLETED;

© 2007 Cisco Systems, Inc. All right reserved.


Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 6 of 17
Class of Parameter for Device Handler, COP

<DISPLAY-COP:COPNO=21;
DISPLAY-COP:COPNO=21;
H500: AMO COP STARTED

COP: 21 INFO:
DEVICE: INDEP SOURCE: DB
PARAMETER:
LINE WITH END-OF-DIAL EOD
SPECIAL MODE SFRM
CODE CALLING RELEASE AFTER EVERY TASK CCR
REGISTRATION OF LAYER 3 ADVISORIES L3AR
MAKE/BREAK RATIO FOR DTMF 1 (PULSE=80MS,PAUSE=80MS) DTM1

CO TRUNK ACCESS:
TRUNK ACCESS TA

TOLL ACCESS:
TRUNK ACCESS TA

AMO-COP -111 CLASS OF PARAMETER FOR DEVICE HANDLER


DISPLAY COMPLETED;

Class of Service, COSSU

<DISPLAY-COSSU:TYPE=COS,COS=10;
DISPLAY-COSSU:TYPE=COS,COS=10;
H500: AMO COSSU STARTED
+------+-----------------+---------------+-----------------+
| COS | VOICE | FAX | DTE |
+------+-----------------+---------------+-----------------+
| 10 |> |
| | TA | NOCO | NOCO |
| | TSUID | NOTIE | NOTIE |
| | TNOTCR | | |
| | RKOABS | | |
| | CDRINT | | |
| | CDRS | | |
| | CDRC | | |
| | COSXCD | | |
| | VCE | | |
| | FWDNWK | | |
| | MSN | | |
| | FWDECA | | |
| | CFB | | |
| | CFNR | | |
| | FWDEXT | | |
| | | | |
+------+-----------------+---------------+-----------------+
AMO-COSSU-111 CLASSES OF SERVICE
DISPLAY COMPLETED;

© 2007 Cisco Systems, Inc. All right reserved.


Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 7 of 17
<DISPLAY-COSSU:TYPE=LCOSV,LCOSV=1;
DISPLAY-COSSU:TYPE=LCOSV,LCOSV=1;
H500: AMO COSSU STARTED
+----+----------------------------------------------------------------+-----+
|LCOS| LAUTH | |
| V | 1 2 3 4 5 6 | |
| |1234567890123456789012345678901234567890123456789012345678901234|COPIN|
| |>SERVICE INFORMATION | NUM |
+----+----+----|----+----|----+----|----+----|----+----|----+----|----+-----+
| 1|X...............................................................| 0 |
| |>LCR ATTENDANT FOR VOICE |
+----+----------------------------------------------------------------+-----+

AMO-COSSU-111 CLASSES OF SERVICE


DISPLAY COMPLETED;
<DISPLAY-COSSU:TYPE=LCOSD,LCOSD=1;
DISPLAY-COSSU:TYPE=LCOSD,LCOSD=1;
H500: AMO COSSU STARTED
+----+----------------------------------------------------------------+-----+
|LCOS| LAUTH | |
| D | 1 2 3 4 5 6 | |
| |1234567890123456789012345678901234567890123456789012345678901234|COPIN|
| |>SERVICE INFORMATION | NUM |
+----+----+----|----+----|----+----|----+----|----+----|----+----|----+-----+
| 1|X...............................................................| . |
+----+----------------------------------------------------------------+-----+

AMO-COSSU-111 CLASSES OF SERVICE


DISPLAY COMPLETED;

Trunk Group Access Code, BUEND

<DISPLAY-BUEND:TGRP=20,FORMAT=L;
DISPLAY-BUEND:TGRP=20,FORMAT=L;
H500: AMO BUEND STARTED

+------------------------------- FORMAT = L -----------------------------------+


| TGRP NUMBER : 20 TGRP NAME : PRI PSSV1 MAXIMUM NO. : 70 |
| CHARCON : NEUTRAL |
| SUBGROUP NO.: 3 DEVICE TYPE : S2CONN TRACENO : 0 |
| RESERVED : N SEARCH MODE : ASCENDING ACD THRESHOLD : * |
| NUMBER OF ASSOCIATED ROUTES : 2 PRIORITY : 2 |
| TDDRFLAG : ON TDDRTHRESHOLD: 3 SOURCEGROUPIDX : 1 |
| GDTRRULE : 0 ACDPMGRP : 0 |
| THE FOLLOWING TRUNKS (LTG-LTU-SLOT-CCT) HAVE BEEN ALLOCATED: |
+------------------------------------------------------------------------------+
| 1- 2- 49-0 1 | 1- 2- 49-0 2 | 1- 2- 49-0 3 |
| 1- 2- 49-0 4 | 1- 2- 49-0 5 | 1- 2- 49-0 6 |
| 1- 2- 49-0 7 | 1- 2- 49-0 8 | 1- 2- 49-0 9 |
| 1- 2- 49-0 10 | 1- 2- 49-0 11 | 1- 2- 49-0 12 |
| 1- 2- 49-0 13 | 1- 2- 49-0 14 | 1- 2- 49-0 15 |
| 1- 2- 49-0 16 | 1- 2- 49-0 17 | 1- 2- 49-0 18 |
| 1- 2- 49-0 19 | 1- 2- 49-0 20 | 1- 2- 49-0 21 |
| 1- 2- 49-0 22 | 1- 2- 49-0 23 | 1- 2- 49-0 24 |
| 1- 2- 49-0 25 | 1- 2- 49-0 26 | 1- 2- 49-0 27 |
| 1- 2- 49-0 28 | 1- 2- 49-0 29 | 1- 2- 49-0 30 |
+------------------------------------------------------------------------------+

AMO-BUEND-111 TRUNK GROUP


DISPLAY COMPLETED;

© 2007 Cisco Systems, Inc. All right reserved.


Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 8 of 17
Trunk Configuration, TDCSU

For Master-side Configuration

<DISPLAY-TDCSU:PEN1=1-2-49-0;
DISPLAY-TDCSU:PEN1=1-2-49-0;
H500: AMO TDCSU STARTED
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2CONN PEN = 1-02-049-0 TGRP = 20 |
|---------------------------------------------------------------------------|
| PROTVAR = ETSI INS = Y SRCHMODE = ASC |
| COTNO = 21 COPNO = 21 DPLN = 0 |
| ITR = 1 COS = 10 LCOSV = 1 |
| LCOSD = 1 CCT = HICOM S2 DESTNO = 1 |
| SEGMENT = 1 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
| TRTBL = GDTR SIDANI = N ATNTYP = TIE |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 1 -1 -300 |
| ALARMNO = 0 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 21 FWDX = 5 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = CCHDL = |
| UUSCCX = 16 UUSCCY = 8 FNIDX = 1 |
| CLASSMRK = EC & G711 & G729OPT SRCGRP = |
| TCCID = |
|---------------------------------------------------------------------------|
| BCNEG = N BCGR = 1 LWPAR = 1 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| SVCDOM = |
| BCHAN = 1 && 30 |
| |
+---------------------------------------------------------------------------+
AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 30

AMO-TDCSU-111 DIGITAL TRUNKS


DISPLAY COMPLETED;

<DISPLAY-LWPAR:FORMAT=L,TYPE=DIUS2,BLNO=1;
DISPLAY-LWPAR:FORMAT=L,TYPE=DIUS2,BLNO=1;
H500: AMO LWPAR STARTED

+-----------------------------------------------------------------------+
| LOADWARE PARAMETERS CIRCUIT TYPE: DIUS2 SOURCE:DB BLOCK: 1 |
+-----------------------------------------------------------------------+
| LNTYPE = COPPER VERSION = S2 QUAL = ON |
| MASTER = Y DCHAN1 = 16 DCHAN2 = 0 |
| PATTERN = D5H QUAL1 = 10 SEC. QUAL2 = 10 MIN. |
| SMD = Y PERMACT = Y FCBAB = DFH |
| CDG = N FIXEDTEI = 0 CNTRNR = 255 |
| TEIVERIF = N CRC4REP = N |
| DEV = INDEP |
| INFO = |
+-----------------------------------------------------------------------+

AMO-LWPAR-111 LOADWARE PARAMETERS FOR NETWORKING MODULES


DISPLAY COMPLETED;

© 2007 Cisco Systems, Inc. All right reserved.


Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 9 of 17
For Slave-side Configuration

<DISPLAY-TDCSU:PEN1=1-2-49-0;
DISPLAY-TDCSU:PEN1=1-2-49-0;
H500: AMO TDCSU STARTED
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2CONN PEN = 1-02-049-0 TGRP = 20 |
|---------------------------------------------------------------------------|
| PROTVAR = ETSI INS = Y SRCHMODE = ASC |
| COTNO = 21 COPNO = 21 DPLN = 0 |
| ITR = 1 COS = 10 LCOSV = 1 |
| LCOSD = 1 CCT = HICOM S2 DESTNO = 1 |
| SEGMENT = 1 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
| TRTBL = GDTR SIDANI = N ATNTYP = TIE |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 1 -1 -300 |
| ALARMNO = 0 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 21 FWDX = 5 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = CCHDL = |
| UUSCCX = 16 UUSCCY = 8 FNIDX = 1 |
| CLASSMRK = EC & G711 & G729OPT SRCGRP = |
| TCCID = |
|---------------------------------------------------------------------------|
| BCNEG = N BCGR = 1 LWPAR = 0 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| SVCDOM = |
| BCHAN = 1 && 30 |
| |
+---------------------------------------------------------------------------+
AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 30

AMO-TDCSU-111 DIGITAL TRUNKS


DISPLAY COMPLETED;

<DISPLAY-LWPAR:FORMAT=L,TYPE=DIUS2,BLNO=0;
DISPLAY-LWPAR:FORMAT=L,TYPE=DIUS2,BLNO=0;
H500: AMO LWPAR STARTED

+-----------------------------------------------------------------------+
| LOADWARE PARAMETERS CIRCUIT TYPE: DIUS2 SOURCE:DB BLOCK: 0 |
+-----------------------------------------------------------------------+
| LNTYPE = COPPER VERSION = S2 QUAL = ON |
| MASTER = N DCHAN1 = 16 DCHAN2 = 0 |
| PATTERN = D5H QUAL1 = 10 SEC. QUAL2 = 10 MIN. |
| SMD = N PERMACT = Y FCBAB = DFH |
| CDG = N FIXEDTEI = 0 CNTRNR = 255 |
| TEIVERIF = N CRC4REP = N |
| DEV = INDEP |
| INFO = |
+-----------------------------------------------------------------------+

AMO-LWPAR-111 LOADWARE PARAMETERS FOR NETWORKING MODULES


DISPLAY COMPLETED;

© 2007 Cisco Systems, Inc. All right reserved.


Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 10 of 17
Configuring the Cisco IAD2432 24FXS

Ericsson-1#sh run
Building configuration...

*Mar 6 19:04:55.133: %SYS-5-CONFIG_I: Configured from console by vty0 (172.20.1


10.100)
Current configuration : 2367 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Ericsson-1
!
boot-start-marker
boot system flash:c2430-ik9o3s-mz-124-9.T1.bin
boot-end-marker
!
card type e1 1
logging buffered 10000000 debugging
no logging console
enable secret 5 $1$WJPz$ZoIKHvDdxxTEDUc2AwOoM0
!
no aaa new-model
!
resource policy
!
network-clock-participate E1 1/0
network-clock-participate E1 1/1
network-clock-select 1 E1 1/0
!
!
no ip domain lookup
!
!
!
isdn switch-type primary-qsig
isdn gateway-max-interworking
!
voice-card 0
!
!
!
!
!
voice service voip
notify redirect ip2pots
!
controller E1 1/0
pri-group timeslots 1-31
!
controller E1 1/1

© 2007 Cisco Systems, Inc. All right reserved.


Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 11 of 17
mode cas
framing NO-CRC4
!
!
!
!
!
!
interface FastEthernet0/0
ip address 172.20.8.40 255.255.255.0
ip broadcast-address 0.0.0.0
duplex auto
speed auto
!
interface FastEthernet0/1
no ip address
ip broadcast-address 0.0.0.0
shutdown
duplex auto
speed auto
!
interface Serial1/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn overlap-receiving
isdn protocol-emulate network
isdn incoming-voice voice
isdn T310 120000
no cdp enable
!
ip default-gateway 172.20.8.1
ip http server
no ip http secure-server
!
ip route 0.0.0.0 0.0.0.0 172.20.8.1
!
!
!
tftp-server flash:c2430-is-mz.sb93109
!
!
control-plane
!
!
!
voice-port 1/0:15
!
voice-port 2/0
!
voice-port 2/1
!
voice-port 2/2
!
voice-port 2/3
!
voice-port 2/4
!
voice-port 2/5

© 2007 Cisco Systems, Inc. All right reserved.


Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 12 of 17
!
voice-port 2/6
!
voice-port 2/7
!
voice-port 2/8
!
voice-port 2/9
!
voice-port 2/10
!
voice-port 2/11
!
voice-port 2/12
!
voice-port 2/13
!
voice-port 2/14
!
voice-port 2/15
!
voice-port 2/16
!
voice-port 2/17
!
voice-port 2/18
!
voice-port 2/19
!
voice-port 2/20
!
voice-port 2/21
!
voice-port 2/22
!
voice-port 2/23
!
!
!
!
dial-peer voice 1100 pots
destination-pattern 11..
supplementary-service pass-through
direct-inward-dial
port 1/0:15
forward-digits all
!
dial-peer voice 4200 voip
destination-pattern 42..
session protocol sipv2
session target ipv4:172.20.8.41
dtmf-relay rtp-nte
supplementary-service pass-through
!
!
gateway
timer receive-rtp 1200
!
sip-ua

© 2007 Cisco Systems, Inc. All right reserved.


Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 13 of 17
!
!
!
line con 0
password cisco
login
line aux 0
line vty 0 4
exec-timeout 0 0
password cisco
login
!
end

Ericsson-1#

© 2007 Cisco Systems, Inc. All right reserved.


Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 14 of 17
Acronyms
Acronym Definitions
IAD Integrated Access Device
SIP Session Initiation Protocol

© 2007 Cisco Systems, Inc. All right reserved.


Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 15 of 17
Important Information
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE

WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO

BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE

FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR

INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA

ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

© 2007 Cisco Systems, Inc. All right reserved.


Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 16 of 17
Corporate European Americas Asia Pacific
Headquarters Headquarters Headquarters Headquarters
Cisco Systems, Inc. Cisco Systems International Cisco Systems, Inc. Cisco Systems, Inc.
170 West Tasman Drive BV 170 West Tasman Drive Capital Tower
San Jose, CA 95134-1706 Haarlerbergpark San Jose, CA 95134-1706 168 Robinson Road
USA Haarlerbergweg 13-19 USA #22-01 to #29-01
www.cisco.com 1101 CH Amsterdam www.cisco.com Singapore 068912
Tel: 408 526-4000 The Netherlands Tel: 408 526-7660 www.cisco.com
800 553-NETS (6387) www-europe.cisco.com Fax: 408 527-0883 Tel: +65 317 7777
Fax: 408 526-4100 Tel: 31 0 20 357 1000 Fax: +65 317 7799
Fax: 31 0 20 357 1100
Cisco Systems has more than 200 offices in the following countries and regions. Addresses, phone numbers, and fax numbers are listed on
the Cisco Web site at www.cisco.com/go/offices.

Argentina • Australia • Austria • Belgium • Brazil • Bulgaria • Canada • Chile • China PRC • Colombia • Costa Rica • Croatia • Czech
Republic • Denmark • Dubai, UAE • Finland • France • Germany • Greece • Hong Kong SAR • Hungary • India • Indonesia • Ireland •
Israel • Italy • Japan • Korea • Luxembourg • Malaysia • Mexico • The Netherlands • New Zealand • Norway • Peru • Philippines •
Poland • Portugal • Puerto Rico • Romania • Russia • Saudi Arabia • Scotland • Singapore • Slovakia • Slovenia • South Africa • Spain •
Sweden • Switzerland • Taiwan • Thailand • Turkey Ukraine • United Kingdom • United States • Venezuela • Vietnam • Zimbabwe
© 2007 Cisco Systems, Inc. All rights reserved.
CCVP, the Cisco Logo, and the Cisco Square Bridge logo are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of
Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo,
Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step,
Follow Me Browsing, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, iPhone, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick
Study, LightStream, Linksys, MeetingPlace, MGX, Networking Academy, Network Registrar, Packet, PIX, ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet,
StackWise, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and
certain other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship
between Cisco and any other company. (0612R)
Printed in the USA

© 2007 Cisco Systems, Inc. All right reserved.


Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com
Page 17 of 17

You might also like